Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 72 views

    Extech 382270 Quad PSU Manual

    Uploaded by

    bo cephus

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Extech 382270 Quad PSU Manual

    Uploaded by

    bo cephus
    72 views6 pages

    Original Title

    extech 382270 Quad PSU manual

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    72 views6 pages

    Extech 382270 Quad PSU Manual

    Uploaded by

    bo cephus

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 6

    User's Guide

    High Precision Quad Output


    DC Power Supply
    Model 382270
    Introduction
    Thank you for selecting the Extech Model 382270. This device is shipped fully tested and calibrated
    and, with proper use, will provide years of reliable service. Please visit the Extech Instruments website
    (www.extech.com) to check for the latest version of this User Guide.

    Safety Information
    International Safety Symbols
    This symbol, adjacent to another symbol or terminal, indicates the user must refer to the
    manual for further information.

    This symbol, adjacent to a terminal, indicates that, under normal use, hazardous voltages
    may be present

    Double insulation

    Safety Precautions
    To ensure safe operation of the equipment and eliminate the danger of serious injury due to short-
    circuit (arcing), the following safety precautions must be observed.
     Prior to connection of the equipment to the mains outlet, check that the available mains
    voltage corresponds to the voltage setting of the equipment.
     Connect the mains plug of the equipment only to a mains outlet with an earth ground
    connection.
     Do not place the equipment on damp or wet surfaces.
     Do not subject the equipment to direct sunlight or extreme temperatures.
     Do not subject the equipment to extreme humidity or dampness
     Replace a defective fuse only with a fuse of the original rating. Never short circuit the fuse or
    the fuse housing
     Do not exceed the maximum permissible input rating.
     Comply with the warning labels and other info on the equipment.
     Do not insert metal objects into the equipment by way of the ventilation slots
     Do not place water-filled containers on the equipment
     Do not operate the equipment near strong magnetic fields (motors, transformer etc.)
     Do not subject the equipment to shocks or strong vibrations
     Keep hot soldering irons away from the equipment
     Allow the equipment to stabilize at room temperature before use
     Do not modify the equipment in any way
     All service and repair must be performed by qualified service personal.

    Cleaning the meter housing


    Prior to cleaning the meter housing, disconnect the mains plug from the power outlet. Clean only
    with a damp, soft cloth and a commercially available mild household cleaner. Ensure that no water
    gets inside the equipment to prevent possible shorts and damage to the equipment.

    2 382270-EU-EN V2.3 9/12


    Power Supply Description
    7 8 9 10

    1. POWER button
    2. Channel 4 Voltage adjustment
    3. Channel 4 overload status LED
    4. Channel 2 Current adjust knob
    11
    5. Constant Current / Voltage status 6
    LED for CH 4 5 12
    6. Channel 2 Voltage adjust knob 4 13
    7. Voltage output display (CH 2/4) 3 14
    2 15
    8. Current output display (CH 2/4)
    9. Current output display (CH 1/3) 1
    10. Voltage output display (CH 1/3)
    11. Channel 1 voltage output adjust knob
    29 26 24 22 20 18 16
    12. Constant Voltage / Current status
    LED for Channel 1 30 28 27 25 23 21 19 17
    13. Current output adjust knob for Channel 1
    14. Channel 4 overload status LED
    15. Voltage output adjust knob for Channel 3
    16. Positive terminal CH 3
    17. CH1 / CH 3 display select button
    18. Negative terminal CH 3
    19. Positive terminal CH 1
    20. SERIES / PARALLEL / INDEPENDENT tracking select button
    21. Negative terminal CH 1
    22. GND terminal
    23. SERIES / PARALLEL / INDEPENDENT tracking select button
    24. Positive terminal CH 2
    25. Output ON-OFF status LED
    26. Negative terminal CH 2
    27. Output ON-OFF button
    28. Positive terminal CH 4
    29. Negative terminal CH 4
    30. CH2 / CH 4 display select button

    3 382270-EU-EN V2.3 9/12


    Operation
    Independent Connections (Channels 1 and 2, adjustable outputs)
    Set the tracking switches (19) and (22) to the spring OUT position (INDEP). Set the Output On/Off
    switch (27) to the ON position.

    Constant Voltage (CV) Mode


    1. Rotate the CC knob (4) for CH 2 or (13) for CH 1 to maximum and then turn on the power
    supply.
    2. Adjust CV knob (6) or (11) for the desired output.
    3. The color of the CV/CC status LED (5) or (12) will turn green.
    4. Current Limiting Note: For CV outputs in general, the CC adjustment should be set to
    maximum, but, for this unit, the current limiting protection point can also be set arbitrarily. To
    do so:
    a) Turn on power
    b) Rotate CC adjustment counter-clockwise to minimum
    c) Short the positive and negative terminals
    d) Rotate the CC adjustment clockwise to the desired current-limiting protection point.

    Constant Current (CC) Mode


    1. Turn on the power supply.
    2. Rotate the CV knob (6) or (11) to maximum.
    3. Rotate the CC adjustment (4) or (13) to minimum
    4. Connect the required load.
    5. Rotate CC adjust knob clockwise to reach the desired current value.
    6. The color of the CV/CC status LED (5) or (12) will turn red.

    4 382270-EU-EN V2.3 9/12


    Series Connection (Channels 1 and 2, adjustable outputs)
    1. Set the tracking switch (20) to the spring OUT position. Press in tracking switch (23).
    2. In Series mode, the slave output will strictly track the master output voltage when the user
    turns the master voltage adjust knob (11). The output voltage in Series mode can be set up to
    double the maximum voltage available in Independent mode (voltage between terminals 19 &
    26).
    3. Ensure that both channels’ negative terminals are NOT connected to case ground. If they are,
    a short circuit will occur.
    4. When the two outputs are configured in Series, the voltage is controlled by the master output
    knob (11), but the current adjustment for the two outputs is still independent. Therefore, ensure
    that the CC adjust knobs (4 and 13) are rotated fully clockwise to maximum for the Series
    circuit to work correctly.
    5. The user must physically short the negative terminal of the Master output (CH1-) with the
    positive terminal of the Slaved output (CH2+).

    Parallel Connection (Channels 1 and 2 adjustable outputs)


    1. Press in both tracking switch (20) and tracking switch (23).
    2. In Parallel mode, the two outputs will always be the same for any setting of the master voltage
    knob (11). The slave CC indicator (5) will switch on.
    3. In Parallel mode the CC adjustment (4) for the slave is not active. The user must adjust the CC
    for the master (CH1) output (13). The current available in parallel mode is up to twice the
    amount available in other modes.
    4. The user must short the two positive terminals. (CH1+ to CH2+)
    5. The user must also short the two negative terminals. (CH1- to CH2-)
    6. Use CH1 voltage control knob (11) to control the voltage level.
    7. Use CH1 CC knob (13) to control current.

    5 382270-EU-EN V2.3 9/12


    Specifications
    Range Specifications

    Output1 Output2 Output3 Output4


    (CH1) (CH2) (CH3) (CH4)
    0~30V/0~5A 0~30V/0~5A 3~6.5V/3A 8~15V/1A

    Electrical Specifications
    Input voltage: 110~127VAC±10%; 220~240VAC±10% (switchable)
    Output voltage and current: See table above
    Line regulation:
    For Two adjustable outputs:
    4
    CV: ≤ 1 x 10¯ + 3mV
    3
    CC ≤ 2 x 10¯ + 3mA
    Two semi-adjustable outputs: ≤ 5mV
    Load regulation:
    Two adjustable outputs:
    4
    CV ≤ 5 x 10¯ + 5mV
    3
    CC ≤ 2 x 10¯ + 5mA
    CH3 ≤30mV
    CH4 ≤15mV
    Ripple and noise:
    Two adjustable outputs:
    CV ≤ 1mV rms
    CC ≤ 3mA rms
    Fixed output: ≤ 2mV rms
    Protection: current-limit
    Display accuracy:
    Volt-indication: LED ± (0.5%rdg+2 digits)
    Amp-indication: LED ± (0.5%rdg+2 digits)
    General Specifications
    Display: Four 3-digit color-coded LED displays and four status LED lights
    Dimensions: 260 x 160 x 370mm (10.2 x 6.3 x 14.6") (W x H x D)
    Weight: 12 kg (26.4lbs)

    Copyright © 2013 FLIR Systems, Inc. 
    All rights reserved including the right of reproduction in whole or in part in any form 
    www.extech.com 
    ISO‐9001 Certified 

    6 382270-EU-EN V2.3 9/12

    You might also like