Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 26 views

    Zurn X6915-XL Troubleshooting

    Uploaded by

    bo cephus

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Zurn X6915-XL Troubleshooting

    Uploaded by

    bo cephus
    26 views1 page

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    26 views1 page

    Zurn X6915-XL Troubleshooting

    Uploaded by

    bo cephus

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    SPECIFICATIONS OPERATION

    Voltage: 6 VDC 1.) Invisible light rays are continually emitted from the faucet
    (4 “AA” Alkaline) sensor.
    Sensor Range: 7.5" Approximate 2.) When the user’s hands come into range of the sensor’s detection
    Operating Water zone (8" approximate), the beam is reflected back to the
    Pressure: 20-80 psi sensor’s receiver and converted to a low voltage electrical
    signal activating a solenoid valve.
    Ambient
    Temperature: 32°F to 122°F (0°C to 50°C) 3.) After the user removes their hands, the absence of reflected
    Operational Water light stops the low voltage electrical signal, closing the valve.
    Temperature: 35°F to 140°F (2°C to 60°C) The circuit automatically resets for the next user.
    Aerator: 2.0 GPM Vandal-Resistant (Standard) 4.) If an object is in view continuously for thirty seconds, the
    faucet will automatically shut off. The faucet will remain off
    CARE AND CLEANING INSTRUCTIONS until the object is removed. After the object is removed, the
    DO NOT use abrasive or chemical cleaners to clean faucets as they faucet functions normally.
    will dull the luster and attack the chrome or special decorative
    finishes. Use only mild soap and water, then wipe dry with a clean
    cloth or towel. While cleaning the bathroom tile and floor, the faucet
    Battery-Powered Faucets

    and electronics should be protected from splattering of water, cleaner,


    AquaSense ‘A’

    acids, and cleaning fluids that can damage the sensor faucet.

    TROUBLESHOOTING GUIDE
    PROBLEM POSSIBLE CAUSE TO DIAGNOSE REMEDY
    FAUCET WILL NOT Water supply not turned on. Check supply stops. Turn on water.
    FLOW WATER
    Batteries not connected. Check connections. Reconnect batteries.

    Cable connection is not Check cable connection. Remove battery, and disengage the cable
    fully engaged. connection. Check cable connection for broken
    pins and reconnect cable. Check battery for
    voltage level and reinstall.

    Low battery. Flashing red light in sensor eye Remove batteries and replace with
    indicates low battery. four (4) new alkaline batteries.

    Solenoid valve inoperative. Move hand in front of faucet to If clicking, open solenoid valve
    see if solenoid valve is clicking. and clean it.

    If not clicking, replace solenoid valve.

    Sensor/electronics are Move hand in front of faucet to Remove the battery and short circuit the
    inoperative. see if solenoid valve is clicking. battery terminals with Allen wrench. This will
    See note in Step 4. reset the electronics. Replace battery.

    Filter is plugged. Shut off water supply. Remove Clean the filter and reassemble.
    clean out cap.

    FAUCET CONTINUES Solenoid valve is dirty. Open the solenoid valve and check for Shut off water supply. Disassemble solenoid
    TO RUN FOR MORE debris. Carefully observe the way and remove debris from diaphragm and/or
    THAN 30 SECONDS valve goes together for reassembly. plunger tip. Reassemble solenoid.
    OR DRIPS

    ZURN INDUSTRIES, INC. COMMERCIAL BRASS OPERATION, 5900 ELWIN BUCHANAN DRIVE, SANFORD, NC, U.S.A. 27330
    PHONE: 1-800-997-3876 FAX: 919/775-3541 WEBSITE: www.zurn.com
    ZURN INDUSTRIES LIMITED 3544 NASHUA DRIVE, MISSISSAUGA, ONTARIO L4V 1L2 PHONE: 905/405-8272 FAX: 905/405-1292

    © 2003 Zurn Industries, Inc. Printed in the U.S.A. Form No. FV254, 1/03

    You might also like