Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 185 views

    1 3 B.E / B.Tech. Practical End Semester Examinations, April / May 2019

    Uploaded by

    Maheswari
    This document outlines the practical end semester examinations for a fourth semester circuits design and simulation laboratory course. It lists 20 examination questions, each worth 100 marks, involving designing, constructing, and simulating various circuit designs including feedback amplifiers, oscillators, filters, and signal processing circuits. Students are instructed to complete one of the listed circuit design, analysis, and simulation assignments within the allotted 3 hour examination period.

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd

    1 3 B.E / B.Tech. Practical End Semester Examinations, April / May 2019

    Uploaded by

    Maheswari
    185 views3 pages
    This document outlines the practical end semester examinations for a fourth semester circuits design and simulation laboratory course. It lists 20 examination questions, each worth 100 marks, involving designing, constructing, and simulating various circuit designs including feedback amplifiers, oscillators, filters, and signal processing circuits. Students are instructed to complete one of the listed circuit design, analysis, and simulation assignments within the allotted 3 hour examination period.

    Original Description:

    ADC QP

    Original Title

    EC8461 - 22.4 (set 4)

    Copyright

    © © All Rights Reserved

    Available Formats

    DOC, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document outlines the practical end semester examinations for a fourth semester circuits design and simulation laboratory course. It lists 20 examination questions, each worth 100 marks, involving designing, constructing, and simulating various circuit designs including feedback amplifiers, oscillators, filters, and signal processing circuits. Students are instructed to complete one of the listed circuit design, analysis, and simulation assignments within the allotted 3 hour examination period.

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    185 views3 pages

    1 3 B.E / B.Tech. Practical End Semester Examinations, April / May 2019

    Uploaded by

    Maheswari
    This document outlines the practical end semester examinations for a fourth semester circuits design and simulation laboratory course. It lists 20 examination questions, each worth 100 marks, involving designing, constructing, and simulating various circuit designs including feedback amplifiers, oscillators, filters, and signal processing circuits. Students are instructed to complete one of the listed circuit design, analysis, and simulation assignments within the allotted 3 hour examination period.

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    of 3

    Page 1 of 3

    B.E / B.Tech. PRACTICAL END SEMESTER EXAMINATIONS, APRIL / MAY 2019

    Fourth Semester

    EC 8461 – CIRCUITS DESIGN AND SIMULATION LABORATORY


    (Regulations – 2017)

    Time: 3 Hours Maximum Marks: 100


    Answer any one Question

    Aim/Principle/Apparatus Tabulation/Circuit / Calculation Viva-Voce Record Total


    required/Procedure Program/Drawing & Results

    20 30 30 10 10 100

    1. Design a current series feedback amplifier and determine the frequency response, gain,
    bandwidth and calculate the input impedance and output impedance with and without
    Feedback. Assume Ic = 1mA, VRE = 1V, R2 = 10KΩ, VCC = 12 V. (100)
    2. Design a voltage shunt feedback amplifier and determine the frequency response, gain,
    bandwidth and calculate the input impedance and output impedance. Assume I C = 1 mA,
    VRE = 1V, R2 = 10 KΩ, VCC = 12 V. (100)
    3. Design a current shunt feedback amplifier and determine the frequency response, gain,
    bandwidth and calculate the input impedance and output impedance with and without
    Feedback. Assume Ic = 1mA, VRE = 1V, R2 = 10KΩ, VCC = 12 V. (100)
    4. Design a voltage series feedback amplifier and determine the frequency response, gain,
    bandwidth and calculate the input impedance and output impedance. Assume I C = 1 mA,
    VRE = 1V, R2 = 10 KΩ, VCC = 12 V. (100)
    5.
    Construct a Wien bridge oscillator to obtain the sine wave for a frequency of 1kHz. (100)
    6. Design and construct a RC phase shift oscillator to obtain the sine wave for a frequency of
    1kHz. Assume C = 0.01 μF. (100)
    7. Design and construct a Hartley oscillator to get a sine wave output of 2 KHz frequency.
    (100)
    8. Design and construct a Colpitts oscillator to get a sine wave output of 2 KHz frequency.
    (100)
    9. Design and construct a single tuned amplifier for a resonant frequency of 2 KHz and
    determine the frequency response of the amplifier. (100)
    Page 2 of 3
    10. (i) Design and construct a Differentiator circuit and obtain the output waveforms for the
    square and sine waveform as input. (50)
    (ii) Simulate a flip flop multivibrator circuit and obtain the corresponding waveform.
    (50)

    11. (i) Design and construct a Integrator circuit and obtain the output waveforms for the
    square and sine waveform as input. (50)
    (ii) Simulate a double tuned amplifier circuit and obtain the corresponding waveform. (50)

    12. (i) Construct the following clipper circuit and obtain the corresponding output if the input
    is a sine wave of 12 V(p-p).
    a. Positive clipper b. Negative Clipper (50)
    (ii) Simulate a Schmitt trigger circuit with predictable hysteresis waveform. (50)
    13. Construct the clipper and clamper circuit for both positive and negative and obtain the
    corresponding waveform, if the input is a sine waveform of amplitude 10 V(p-p). (100)
    14. (i) Construct the following clamper circuit and obtain the corresponding output if the
    input is a sine wave of 12 V(p-p).
    a. Positive clamper b. Negative Clamper (50)
    (ii) Simulate a Twin-T oscillator circuit and obtain the corresponding waveform. (50)
    15. (i) Design and construct a free running multivibrator to get an output square waveform
    and calculate its TON and TOFF. (50)
    (ii) Simulate a Bistable multivibrator circuit and obtain the corresponding waveform.
    (50)
    16. (i) Design and construct a one-shot multivibrator to get an output pulse waveform and
    calculate its TON and TOFF. (50)
    (ii) Simulate a stagger tuned amplifier circuit and obtain its corresponding waveform.
    (50)
    17. (i) Construct the positive clamper circuit and obtain the corresponding waveform, if the
    input is a sine waveform and a square waveform of amplitude 5 V(p-p). (50)
    (ii) Simulate a Wien bridge Oscillator circuit and obtain the corresponding waveform.
    (50)
    18. (i) Construct the following clipper circuit and obtain the corresponding output if the input
    is a sine wave of 12 V(p-p).
    a. Biased positive clipper with VR = + 5V
    b. Biased negative clipper with VR = - 5V (50)
    (ii) Simulate a Twin-T Oscillator circuit and obtain the corresponding waveform. (50)
    Page 3 of 3
    19. (i) Construct the negative clamper circuit and obtain the corresponding waveform, if the
    input is a sine waveform and a square waveform of amplitude 5 V(p-p). (50)
    (ii) Simulate and analyze the power amplifier circuit and obtain the corresponding
    waveform. (50)
    20. (i) Design and construct an Integrator circuit and obtain the output waveforms for the
    square and sine waveform as input. (50)
    (ii) Simulate a Tuned Collector Oscillator circuit and obtain the corresponding waveform.
    (50)

    You might also like