R-410A

60Hz

AUMR + CADX-A
Series
Split Air Conditioners

Range 5 TR to 25 TR
(18 kW to 88 kW)

facebook.com/skmaircon www.skmaircon.com @ skmaircon

 SKM Split Air Conditioners
AUMR + CADX-A Series - R-410A

Contents

Introduction................................02 Typical Wiring Diagram .........................11

Introduction
Legend........................................02 ElectricaL Data.....................................12
Nomenclature.............................02 Dimensional Data ...............................13
Component Features.......................03 Loading Points & Line Sizes..................17
Optional Features............................05 Recommended Clearances ................18
The new series of SKM air cooled split
Specifications..................................06 system air conditioner has been developed to
Installation and commissioning .........19
Capacity Ratings..............................08 satisfy the needs in air conditioning practices,
Guide Specifications..........................21
meet high quality of job requirements every
Fan Performance..............................10
time and to deliver the best in split system
performance.

Legend SKM air cooled split air conditioners consist

of ceiling suspended indoor air handler
(CADX-A) matched with floor mounted
The following legends are used throughout this manual:
outdoor air cooled condensing unit (AUMR)
cfm......... Cubic feet per minute PI........... Power Input of Compressor series.
Hz.......... Hertz TR.......... Tons of Refrigeration
SKM air cooled split air conditioners available
kW......... Kilowatts V............ Volts
in 11 variations to cover the range from 5 TR
kg........... Kilogram kPa ....... Kilopascal
to 25 TR (18 kW to 88 kW) in 60Hz at nominal
lbs.......... Pounds EWB...... Evaporator Wet Bulb air AHRI conditions. It is suitable to operate in
l/s .......... Liters per second entering temperature a wide range of ambient temperatures from
MBh....... BTUH x 1000 BPF....... By Pass Factor 50 °F (10°C) to 125°F (51.7°C).
Ph.......... Phase
SKM split units are internally wired and all
that is required to be done on site is ducting,
refrigerant piping, power wiring for CADX-A
Nomenclature motor from AUMR, thermostat wiring and
power supply connection which reduces
A U M R - 060 E installation work and consequently keeps
costs to a minimum. Two independent
refrigeration circuits are provided when two
compressors are used.
Air Cooled Power Suppy Code
E: 460V/3Ph/60Hz
R: 380V/3Ph/60Hz SKM provides qualified service and stock
Condensing Units
T: 220V/3Ph/60Hz of replacement parts in all major cities of
Hermetic Scroll Compressor the G.C.C. countries, Egypt, Jordan, and
Nominal Capacity (MBh) Pakistan. See back cover for details or call
R-410A
SKM.

CA DX - 060 A E
SKM Airconditioning LLC

Comfort Air Conditioner Power Suppy

E: 460V/3Ph/60Hz
Direct Expansion Cooling Coil R: 380V/3Ph/60Hz
T: 220V/3Ph/60Hz

Applicable for R-410A

Model Designatioin

SKM reserves the right to change, in part or in You name it.....We cool it
whole the specifications of its Air Conditioning
Equipment at any time in order to add the latest
technology. Therefore, the enclosed information
may change without any prior notice.

2
SKM Split Air Conditioners
AUMR + CADX-A Series - R-410A
General Features Condenser Coils
SKM split system air conditioners incorporate many features Condenser coils are manufactured from cross fin Waffle Louvre
and benefits in both the air handler and condensing units, which and Hi-X seamless copper tubes mechanically bonded to
together provides a heavy duty, robust and long lasting commercial aluminium fins to ensure optimum heat transfer. All coils are
unit’s application. tested against leakage by high air pressure under water. An
integral subcooling circuit is incorporated in the lower section
SKM split air conditioners combined high efficiency components of the condenser to increase system capacity. The additional
to provide an extremely rugged and energy efficient split system condenser surface provides more cooling using less energy at
that will provide cooling with higher efficiency for a long and no additional cost.
extended period of time.

SKM split system AUMR + CADX-A is yet another model in the Condenser Fans
top class range of SKM products which uses the following basic
components: Condenser fans are propeller type with aluminium alloy blades
and are directly driven by electric motors. Motors are Totally
• High efficiency totally sealed scroll hermetic compressor. Enclosed Air Over (TEAO), six pole or four pole with Class F
insulation and minimum IP-54 protection. The TEAO and Class
• Totally enclosed,Class F insulated, condenser and evaporator
fan motors. F insulation features ensure long life and are unique to SKM.
The condenser fans are individually statically and dynamically
• Heavy duty condenser and evaporator coils optimized and
balanced at the factory. Complete fan assembly is mounted
designed for a long life maintenance free operation.
downward on the strong and acrylic coated fan guard for the
• Cabinet construction specifically for gulf climate condition. smaller units. For larger units fan, assembly is separate and
• Electronic control board for the unit operation. provided with suitable acrylic coated fan guard.
• Factory matched performance and reliable output to minimize
field decisions.
• Many standard features which are not included in residential Control Panel
domestic type split systems.
• Typically, much heavier gauge tubing and thicker fins for The AUMR series Condensing units are provided with IP-54
ruggedness and long life. control panel enclosure comprising all starting, operating and
safety controls.

Main Component Features The following are the standard components used in all AUMR
control panel:
AUMR Condensing Unit
• Starting contactors for compressors and motors.
Compressors • Internal overload protection for compressors.
Compressors used in the AUMR series condensing units are • Internal OR External overload protection for the motors
hermetically sealed, hi-efficiency, low noise, and compact scroll (depending on the model).
with the following features: • Electronic control board for unit operation.
• Diagnostic LEDs on the control board for easy
• High Efficiency.
troubleshooting .
• Quiet operation, Low Sound levels.
• Compressor short cycling protection.
• Compact and light.
• Control switch for unit on/off.
• Limited wear.
• Control circuit breaker.
• 70% fewer moving parts than comparably sized reciprocating
• Power and control circuit terminal blocks.
compressors.
• High pressure protection.
• Unique ability to hadle liquid refrigerant.
• Low pressure protection.
• Suction gas motor cooling.
• Starter (contactor & overload relay) for CADX-A evaporator
• Suction screen. fan motor.
• Centrifugal oil pumps with filter and magnet. (Power wiring from AUMR control panel to CADX-A
• Brazed fittings or Rotalock options. motor to be done at site by others)

• Two refrigerant circuits on larger units provides efficient

part load.
• No internal valves.

3
 SKM Split Air Conditioners
AUMR + CADX-A Series - R-410A
Casing and Structure Refrigerant R- 410A
The unit casing used in AUMR series is made of hot dip Why 410A?
galvanized (zinc coated) steel sheets, conforming to JIS-G 3302
R-410A has a higher volumetric cooling capacity compared to
and ASTMA525, which is phosphatized and baked after an
R-22 and has better thermal exchange properties. This results
electrostatic powder coat of approx. 60 microns. This finish and
in overall performance gains in terms of system efficiency. The
coating can pass a 1000 hour in 5% salt spray testing at 95°F
greater density of the vapour in R-410A permits higher system
(35°C) and 95% relative humidity as per ASTM B117. velocities, reduces pressure drop losses and allows smaller
diameter tubing to be used. In other words a smaller unit can
be developed using a smaller displacement compressor, less
CADX-A Air Handling Unit coil and less refrigerant while maintaining system efficiencies
comparable to current day R-22 equipment.

Evaporator Coils Benefits

• No ozone depletion potential or phase-out date
All evaporator coils are made of inner grooved copper tubes
mechanically bonded into cross wave aluminum fins to ensure Using chlorine-free R-410A with zero Ozone Depletion
optimum heat transfer. Coils conform to AHRI-410. All evaporator Potential (ODP) helps protect both the environment and your
coils are tested against leakage by 450 psig high pressure under investment. That’s because new equipment using R-410A
water. Each evaporator coil is supplied with a factory sized and faces no mandated phase-out date over a 20 to 30 year
matched thermostatic expansion valves and 4 mounting holes equipment life expectancy.
for ceiling suspension.
• Reduced service costs
R-410A refrigerant has no significant “glide.” If a leak occurs,
Evaporator Fan & Drive only the lost refrigerant must be replaced.

Attention points
Evaporator fans are forward curved centrifugal double inlet, double
width, statically and dynamically balanced. Bearings used in the • Pressure level: 1.6 times of R-22.
fans are self aligning and lubricated for life. Evaporator fans are • Lubricating oil: Ester Oil absorb moisture easily
belt driven and use “V” belts with an adjustable variable pitch (Never mix with mineral oil).
motor pulley resulting in an accurate fan air flow adjustment. • Tools exclusive for R-410A.
• Never mix R410A with other refrigerant.
Fans are driven by Totally Enclosed, IP-55 Protected, 4 pole • Driers, valves and even copper tube must be approved for
Class F insulated electric motors. The motors are factory wired to use with R-410A.
the control panel where the motor starters are located to control
• Never allow refrigerant cylinders to exceed (60°C).
the operation of the motors. The motors conform to relevant IEC
standards.

Optional Features
Filter
As with all SKM air conditioning units, the AUMR Series
All CADX-A units are supplied as standard with 1” (25mm) Split Units are available with multitude of optional features
thick permanent washable expanded aluminum flat filter having available on request:
average dust arrestance 54% according to ASHRAE standard Alternative Condenser Material
52-76.
Made of copper tubes and alternative fin material and/or
protective coats.
• For Pre Coated aluminum fins, specify (FAP).
Casing \ Structure
• For Aluminum Fins with Aeris Coat Protection, specify (FAA).
The unit casing for CADX-A is made of zinc coated galvanized • For Copper Fins, specify (FC).
steel sheets conforming to JIS-G3302 and ASTM A525 which • For Copper Fins with Aeris Coat Protection, specify (FCA).
is phosphatized and baked after an electrostatic powder coat
of approximately 60 microns. This finish and coating can pass
a 1000 hour in 5% salt spray testing at 95°F (35°C) and 95% Alternative Evaporator Material
relative humidity as per ASTM B117. Panels and casing are Made of copper tubes and alternative fin material and/or
insulated with 1” (25mm) thick fiberglass (with BGT coating) protective coats.
thermal and acoustic insulation having density of 2 lb/ft³. (32
kg/m³) and thermal conductivity of 0.23 BTU.in/ft²°Fh (0.033 • For Copper Fins specify (EFC) .
W/m°K). Insulation meets the requirements of NFPA 90A and • For Precoated Aluminum Fins, specify (EFAP) .
90B for fire resistance. • For Aluminum Fins with Aeris Coat Protection, specify (EFAA).
• For Copper Fins with Aeris Coat Protection, specify (EFCA).

4
SKM Split Air Conditioners
AUMR + CADX-A Series - R-410A
Voltage Monitoring Module (VMM) Heater
Provides protection to AUMR Series Condensing unit in the Stages
(kW)
event of:
• Phase burn-out. 060 060A 6
• Phase reversal. 070 070A 7.5
• Under / over voltage on the incoming line voltage.
090 090A 9
100 100A 1
High & Low Pressure Gauges (SDG1)
105 105A 12
Unit mounted for each compressor to monitor the high and
low-side operating pressure. 120 120A
150 150A 15
2” (50mm) Flat Filter Section (FFS)
For heavy filtration, need a section, can be provided without or
180 180A 18
with aluminium cleanable filter 2” filter add 2AF). 215 215A
2
240 240A 24
Liquid Line Controls (CRSP)
Refrigeration specialties comprising solenoid valve, filter drier, 300 300A
Table 1
sight glass and ball valve. Factory sizing and selection ensures
correctly sized and selected components to complete the field
installation. Pump Down Facility with solenoid valve (PDS)
The compressors will switch off each time with a Pumpdown Cycle
Electric Heating (HTR1) inorder to prevent Liquid refrigerant migration to the compressor
Eectric heating batteries are made up of finned heating during Off Cycle periods.
elements, constructed from high quality 80/20 nickel chrome With this option, each circuit will be provided with an additional
resistance wire centred in metal tube by compressed discharge check valve to prevent Refrigeration Migration from
magnesium oxide. Helical fins are tightly wound around the High side to Low side when the compressor is off.
tubular heating element.
Heater batteries when ordered comes with CADX-A mounted
control panel consisting of stage contactors, primary auto reset Low voltage thermostat (CHTS)
thermal safety cut-out, secondary manual reset thermal safety Wall mounted 24 volts cooling/heating thermostats, supplied
cut-out and air flow switch. Control of the heater stages will be loose for field installation.
from AUMR control panel through heating/cooling thermostat
(either supplied by SKM or by customer). Circuit Breaker for Compressor (CBC)
Following are the optional kW ratings for electric heater. For those electrical specification which requires additional short
circuit and overload protection for the compressors.
BMS Interface Volt free Contacts (BMVF)
Pressure Relief Valve (PRV)
Volt free contacts for run status, common fault status, auto
mode status and provision for remote on/off shall be provided To protect the unit from being over-pressurized.
as option if required.

Rotalock Valves on compressors (RVC)
For additional requirements, please contact SKM.
For additional facilitation of maintenance of unit.
Manual Reset Type High Pressure Switch (MHP)
Condenser Coil Guard (CGP)
To replace standard auto reset, capsule type pressure switch.
Wire mesh guard, in painted finish for condenser coils.
Recommended on ground level installations where coil needs
Run Hour Meter(s) (RHM)
to be protected against vandalism.
To monitor operating hours of each compressor.
External Overload Protection (EOP)
Anti-Freeze Thermostat (AFT) For those electrical specification requires additional overload
For evaporator coil freeze-up protection. protection for the compressors.

Stainless Steel Drain Pan (SDP) Double Skin Insulation (DSI)

Stainless Steel Drain Pan 304 Inner skin in the evaporator section is provided with foam board
insulation.

Up size motor (USM)

Unit with one up size evaporator motor.

5
 SKM Split Air Conditioners
AUMR + CADX-A Series - R-410A
CONDENSING UNIT SPECIFICATIONS - OUTDOOR
CONDENSING UNIT SPECIFICATIONS

Condensing Unit AUMR 060 070 090 100 105 120
Matched Air Handling Unit CADX A 060A 070A 090A 100A 105A 120A
MBh 66.9 73.9 91.4 103.6 105.9 131.2
Cooling Capacity (1)
kW 19.6 21.7 26.8 30.4 31.0 38.4
MBh 60.4 66.2 80.9 93.8 94.0 118.5
Cooling Capacity (2)
kW 17.7 19.4 23.7 27.5 27.5 34.7
Capacity Steps % 100-0 100-0 100-0 100-0 100-50-0 100-50-0
Type Hermetic - Scroll
Compressor
Qty. 1 1 1 1 2 2
Type Waffle louver fins and Hi-X tubes 3/8'' OD
Qty. 1 1 1 1 2 2
Outdoor Coil
ft² 20.0 20.0 26.7 26.7 40.0 40.0
Face Area
m² 1.86 1.86 2.48 2.48 3.72 3.72
No. Refrigerant Circuits 1 1 1 1 2 2
Liquid in 1/2 1/2 1/2 5/8 1/2 ( 2x ) 1/2 ( 2x )
Connections (3)
Suction in 7/8 7/8 1 1/8 1 1/8 7/8 ( 2x ) 7/8 ( 2x )
Type Propeller Direct Drive
Code/Qty 550 / 1 550 / 1 723 / 1 723 / 1 550 / 2 550 / 2
Outdoor Fan
cfm 5390 5390 8500 8410 10940 10780
Air Flow
l/s 2544 2544 4011 3969 5163 5087
Type Totally Enclosed Air Over, Class-F insulation, 4 pole or 6 pole, IP54 protected
Motor
Size / Qty. kW / # 0.36 / 1 0.36 / 1 1.1 / 1 1.1 / 1 0.36 / 2 0.36 / 2
Refrigerant Operating Charge lbs 9.7 9.8 8.6 13.9 12.4 19.1
R-410A (4) kg 4.4 4.4 3.9 6.3 5.6 8.7
lbs 332 346 343 427 567 641
Operating Weight Approximate
kg 151 157 156 194 257 291

Condensing Unit AUMR 150 180 215 240 300

Matched Air Handling Unit CADX A 150A 180A 215A 240A 300A
MBh 154.0 183.1 213.0 240.7 304.8
Cooling Capacity (1)
kW 45.1 53.6 62.4 70.5 89.3
MBh 138.2 164.1 189.0 215.7 270.0
Cooling Capacity (2)
kW 40.5 48.1 55.4 63.2 79.1
Capacity Steps % 100-50-0 100-50-0 100-50-0 100-50-0 100-50-0
Type Hermetic - Scroll
Compressor
Qty. 2 2 2 2 2
Type Waffle louver fins and Hi-X tubes 3/8'' OD
Qty. 2 2 2 2 2
Outdoor Coil
ft² 40.00 40.00 40.00 54.67 54.67
Face Area
m² 3.72 3.72 3.72 5.08 5.08
No. Refrigerant Circuits 2 2 2 2 2
Liquid in 1/2 ( 2x ) 1/2 ( 2x ) 5/8 ( 2x ) 5/8 ( 2x ) 5/8 ( 2x )
Connections (3)
Suction in 7/8 ( 2x ) 1 1/8 ( 2X ) 1 1/8 ( 2X ) 1 1/8 ( 2X ) 1 1/8 ( 2X )
Type Propeller Direct Drive
Code/Qty 630 / 2 630 / 2 723 / 2 729 / 2 823 / 2
Outdoor Fan
cfm 11600 11600 16600 18680 23940
Air Flow
l/s 5474 5474 7834 8815 11298
Type Totally Enclosed Air Over, Class-F insulation, 4 pole or 6 pole, IP54 protected
Motor
Size / Qty. kW / # 0.48 / 2 0.48 / 2 1.1 / 2 1.5 / 2 1.5 / 2
Refrigerant Operating Charge R- lbs 19.3 20.1 24.1 28.4 30.0
410A (4) kg 8.8 9.1 10.9 12.9 13.6
lbs 675 668 821 874 890
Operating Weight Approximate
kg 306 303 372 396 404
Table 2

Notes:
(1) Capacity ratings are based on AHRI Standard 210/240 & 340/360. Evaporator entering air conditions of 80°/67°F (27°/19.5°C)
dry bulb/wet bulb and condenser entering air temperature of 95°F (35°C) dry bulb.
(2) Evaporator entering air conditions of 80°/67°F (27°/19.5°C) dry bulb/wet bulb and condenser entering air temperature of
115°F (46°C ) dry bulb.
(3) Connections are based on 25 ft maximum linear distance between the outdoor & indoor unit and 66 ft maximum lift.

Capacity for condition (1)&(2) is gross which does not include the effect of evaporator fan motor heat.

6
SKM Split Air Conditioners
AUMR + CADX-A Series - R-410A
AIR HANDLING
AIR HANDLING UNIT SPECIFICATIONS - INDOOR
UNIT SPECIFICATIONS

Air Handling Unit CADX A 060A 070A 090A 100A 105A 120A
Matched Condensing Unit AUMR 060 070 090 100 105 120
MBh 66.9 73.9 91.4 103.6 105.9 131.2
Cooling Capacity (1)
kW 19.6 21.7 26.8 30.4 31.0 38.4
MBh 60.4 66.2 80.9 93.8 94.0 118.5
Cooling Capacity (2)
kW 17.7 19.4 23.7 27.5 27.5 34.7
Type Hi-X tubes 3/8'' OD
Indoor Coil ft² 5.8 5.8 8.0 8.0 8.0 8.0
Face Area
m² 0.54 0.54 0.74 0.74 0.74 0.74
Refrigerant Control Thermostatic Expansion Valve(s)
Liquid in 1/2 1/2 1/2 5/8 1/2 ( 2x ) 1/2 ( 2x )
Connections (3)
Suction in 7/8 7/8 1 1/8 1 1/8 7/8 ( 2x ) 7/8 ( 2x )
Type Centrifugal DIDW Belt Drive
Code 10/10 10/10 12/12 12/12 12/12 12/12
Indoor Fan
cfm 2000 2400 3000 3400 3400 3600
Air Flow
l/s 944 1133 1416 1605 1605 1699
Type Totally Enclosed Fan Cooled, Class-F insulation, 4-pole, IP55 Protected.
Motor
Size / Qty. kW / # 0.55 / 1 0.75 / 1 1.1 / 1 1.1 / 1 1.1 / 1 1.5 / 1
lbs 226 226 305 312 310 334
Operating Weight Approximate
kg 102 102 138 141 141 151

Air Handling Unit CADX A 150A 180A 215A 240A 300A

Matched Condensing Unit AUMR 150 180 215 240 300
MBh 154.0 183.1 213.0 240.7 304.8
Cooling Capacity (1)
kW 45.1 53.6 62.4 70.5 89.3
MBh 138.2 164.1 189.0 215.7 270.0
Cooling Capacity (2)
kW 40.5 48.1 55.4 63.2 79.1
Type Hi-X tubes 3/8'' OD
Indoor Coil ft² 11.7 14.2 19.4 19.4 19.4
Face Area
m² 1.08 1.32 1.80 1.80 1.80
Refrigerant Control Thermostatic Expansion Valve(s)
Liquid in 1/2 ( 2x ) 1/2 ( 2x ) 5/8 ( 2x ) 5/8 ( 2x ) 5/8 ( 2x )
Connections (3)
Suction in 7/8 ( 2x ) 1 1/8 ( 2X ) 1 1/8 ( 2X ) 1 1/8 ( 2X ) 1 1/8 ( 2X )
Type Centrifugal DIDW Belt Drive
Code 15/15 12/12 R2 15/15 R2 15/15 R2 15/15 R2
Indoor Fan
cfm 4800 6200 7200 8000 8000
Air Flow
l/s 2265 2926 3398 3775 3775
Type Totally Enclosed Fan Cooled, Class-F insulation, 4-pole, IP55 Protected.
Motor
Size / Qty. kW / # 1.5 / 1 2.2 / 1 2.2 / 1 2.2 / 1 3.0 / 1
lbs 442 470 673 678 712
Operating Weight Approximate
kg 200 213 305 307 323
Table 3

Notes:

(1) Capacity ratings are based on AHRI Standard 210/240 & 340/360. Evaporator entering air conditions of 80°/67°F (27°/19.5°C)
dry bulb/wet bulb and condenser entering air temperature of 95°F (35°C) dry bulb.
(2) Evaporator entering air conditions of 80°/67°F (27°/19.5°C) dry bulb/wet bulb and condenser entering air temperature of
115°F (46°C ) dry bulb.
(3) Connections are based on 25 ft maximum linear distance between the outdoor & indoor unit and 66 ft maximum lift.

Capacity for condition (1)&(2) is gross which does not include the effect of evaporator fan motor heat.

7
 SKM Split Air Conditioners
AUMR + CADX-A Series - R-410A
GROSS CAPACITY RATINGS
AFR Condenser Entering Air Temperature
AUMR EWB 95°F (35°C) 105°F (40.6°C) 115°F (46.1°C) 118.4°F (48°C) 125°F (51.7°C)
cfm
+
CADX-A l/s Total Capacity Sensible Capacity PI* Total Capacity Sensible Capacity PI* Total Capacity Sensible Capacity PI* Total Capacity Sensible Capacity PI* Total Capacity Sensible Capacity PI*
(BPF) °F °C MBh kW MBh kW kW MBh kW MBh kW kW MBh kW MBh kW kW MBh kW MBh kW kW MBh kW MBh kW kW
1597 62 16.7 59.4 17.4 49.8 14.6 4.2 55.8 16.4 48.2 14.1 4.9 52.1 15.3 46.6 13.7 5.6 50.9 14.9 46.1 13.5 5.8 48.5 14.2 45.1 13.2 6.3
754 67 19.4 64.5 18.9 41.7 12.2 4.3 61.5 18 40.6 11.9 4.9 58.2 17.1 39.3 11.5 5.6 57.1 16.7 38.9 11.4 5.9 55 16.1 38 11.1 6.3
0.17 72 22.2 69.6 20.4 33.5 9.8 4.3 66.3 19.4 32.3 9.5 5 62.9 18.4 31.1 9.1 5.7 61.7 18.1 30.7 9 5.9 59.4 17.4 29.9 8.8 6.3
060 2000 62 16.7 60.4 17.7 55.2 16.2 4.2 57 16.7 53.8 15.8 4.9 53.4 15.7 52.3 15.3 5.6 52.2 15.3 51.8 15.2 5.8 49.9 14.6 49.9 14.6 6.3
+ 944 67 19.4 66.9 19.6 46.1 13.5 4.3 63.8 18.7 44.9 13.2 4.9 60.4 17.7 43.6 12.8 5.6 59.2 17.3 43.2 12.6 5.9 56.4 16.5 42.1 12.3 6.3
060A 0.19 72 22.2 72.1 21.1 36.2 10.6 4.3 68.6 20.1 35 10.3 5 65 19.1 33.8 9.9 5.7 63.8 18.7 33.4 9.8 5.9 58.5 17.1 42.9 12.6 6.0
3193 62 16.7 63.1 18.5 63.1 18.5 4.3 59.8 17.5 59.8 17.5 4.9 56.2 16.5 56.2 16.5 5.6 55 16.1 55 16.1 5.8 52.7 15.4 52.7 15.4 6.3
1507 67 19.4 70.8 20.8 57.3 16.8 4.3 66.7 19.5 55.9 16.4 5 62.4 18.3 54.4 16 5.7 61.1 17.9 53.9 15.8 5.9 58.4 17.1 53 15.5 6.3
0.26 72 22.2 76.4 22.4 43.3 12.7 4.4 - - - - - - - - - - - - - - - - - - - -
1597 62 16.7 64.1 18.8 51.9 15.2 5.1 60.7 17.8 50.4 14.8 5.7 56.4 16.5 48.5 14.2 6.5 54.9 16.1 47.8 14 6.7 52.1 15.3 46.6 13.7 7.2
754 67 19.4 69.2 20.3 43.7 12.8 5.1 65.7 19.3 42.3 12.4 5.8 62.1 18.2 40.8 12 6.5 60.9 17.8 40.3 11.8 6.7 58.5 17.1 39.4 11.5 7.2
0.17 72 22.2 74.6 21.9 35.3 10.3 5.2 71 20.8 34 10 5.8 67.1 19.7 32.6 9.6 6.6 65.7 19.3 32.1 9.4 6.8 63 18.5 31.2 9.1 7.3
070 2400 62 16.7 67 19.7 62.8 18.4 5.1 62.9 18.4 61.1 17.9 5.7 58.7 17.2 58.7 17.2 6.5 57.3 16.8 57.3 16.8 6.7 54.7 16 54.7 16 7.2
+ 1133 67 19.4 73.9 21.7 52 15.2 5.2 70.1 20.6 50.6 14.8 5.8 66.2 19.4 49.2 14.4 6.6 64.8 19 48.7 14.3 6.8 61.6 18 47.5 13.9 7.3
070A 0.22 72 22.2 79.5 23.3 40.5 11.9 5.2 75.4 22.1 39.2 11.5 5.9 71 20.8 37.8 11.1 6.7 69.5 20.4 37.3 10.9 6.9 64.0 18.8 48.4 14.2 6.9
3193 62 16.7 68.6 20.1 68.6 20.1 5.1 64.5 18.9 64.5 18.9 5.8 60.4 17.7 60.4 17.7 6.5 59 17.3 59 17.3 6.7 56.4 16.5 56.4 16.5 7.2
1507 67 19.4 76.7 22.5 59.4 17.4 5.2 72.6 21.3 58 17 5.9 67.5 19.8 56.2 16.5 6.6 65.9 19.3 55.6 16.3 6.8 62.7 18.4 54.5 16 7.3
0.26 72 22.2 82.3 24.1 45.1 13.2 5.3 78 22.9 43.8 12.8 6 - - - - - - - - - - - - - - -
2196 62 16.7 79.9 23.4 67.7 19.9 6.6 74.8 21.9 65.5 19.2 7.6 69.7 20.4 63.3 18.5 8.6 68 19.9 62.6 18.3 8.9 65 19 61.3 18 9.5
1036 67 19.4 87.1 25.5 56.8 16.6 6.8 82.6 24.2 55 16.1 7.8 78 22.9 53.2 15.6 8.8 76.4 22.4 52.6 15.4 9.1 75.7 22.2 52.4 15.4 9.3
0.17 72 22.2 93.7 27.5 45.4 13.3 7.1 88.8 26 43.6 12.8 8 83.9 24.6 41.9 12.3 9 82.3 24.1 41.4 12.1 9.2 81.4 23.9 41.1 12.0 9.4
090 3000 62 16.7 82 24 78.5 23 6.7 77.1 22.6 76.5 22.4 7.7 72.2 21.2 72.2 21.2 8.7 70.6 20.7 70.6 20.7 9 67.5 19.8 67.5 19.8 9.5
+ 1416 67 19.4 91.4 26.8 65.2 19.1 7 86.6 25.4 63.4 18.6 8 80.9 23.7 61.3 18 8.9 78.9 23.1 60.6 17.8 9.2 78 22.8 60.3 17.7 9.3
090A 0.21 72 22.2 97.9 28.7 50.5 14.8 7.2 92.7 27.2 48.8 14.3 8.2 - - - - - - - - - - - - - - -
4392 62 16.7 85.1 24.9 85.1 24.9 6.8 80.1 23.5 80.1 23.5 7.8 75.2 22 75.2 22 8.7 73.5 21.5 73.5 21.5 9.1 72.7 21.3 72.7 21.3 9.2
2073 67 19.4 94.7 27.8 77.9 22.8 7.1 88.7 26 75.8 22.2 8 83 24.3 73.8 21.6 8.9 81.1 23.8 73.2 21.5 9.2 80.2 23.5 72.9 21.4 9.3
0.26 72 22.2 - - - - - - - - - - - - - - - - - - - - - - - - -
2196 62 16.7 89.1 26.1 71.9 21.1 6.7 85 24.9 70 20.5 7.5 80.2 23.5 67.9 19.9 8.5 78.3 23 67 19.6 8.8 74.7 21.9 65.5 19.2 9.5
1036 67 19.4 96.3 28.2 60.5 17.7 6.8 92.1 27 58.8 17.2 7.6 87.5 25.7 57 16.7 8.6 85.9 25.2 56.3 16.5 9 82.8 24.3 55.1 16.1 9.6
0.17 72 22.2 104.2 30.5 49.1 14.4 6.9 99.5 29.2 47.4 13.9 7.8 94.6 27.7 45.7 13.4 8.7 92.8 27.2 45 13.2 9.1 89.5 26.2 43.9 12.9 9.7
100 3400 62 16.7 93.8 27.5 88.2 25.8 6.7 88.6 26 86 25.2 7.6 83.4 24.4 83.4 24.4 8.6 81.6 23.9 81.6 23.9 8.9 78.2 22.9 78.2 22.9 9.5
+ 1605 67 19.4 103.6 30.4 73.1 21.4 6.9 98.8 29 71.3 20.9 7.7 93.8 27.5 69.4 20.4 8.7 92 27 68.8 20.2 9.1 88.1 25.8 67.4 19.8 9.7
100A 0.22 72 22.2 111.6 32.7 57 16.7 7 106.3 31.2 55.2 16.2 7.9 100.8 29.6 53.4 15.7 8.8 99 29 52.8 15.5 9.2 95.4 27.9 51.7 15.1 9.8
4392 62 16.7 95.7 28.1 95.7 28.1 6.8 90.7 26.6 90.7 26.6 7.6 85.5 25.1 85.5 25.1 8.6 83.7 24.5 83.7 24.5 8.9 80.3 23.5 80.3 23.5 9.5
2073 67 19.4 107.2 31.4 82.3 24.1 6.9 102.1 29.9 80.5 23.6 7.8 95.9 28.1 78.3 23 8.8 93.7 27.5 77.6 22.7 9.1 89.5 26.2 76.1 22.3 9.7
0.26 72 22.2 115.1 33.7 62.7 18.4 7 109.5 32.1 60.9 17.9 7.9 - - - - - - - - - - - - - - -
2196 62 16.7 91.3 26.8 72.9 21.4 7.6 86.2 25.3 70.6 20.7 8.7 80.2 23.5 67.8 19.9 9.9 77.8 22.8 66.8 19.6 10.2 73.5 21.5 64.9 19 10.9
1036 67 19.4 98.5 28.9 61.4 18 7.7 93.4 27.4 59.3 17.4 8.8 87.7 25.7 57.1 16.7 9.9 85.8 25.2 56.3 16.5 10.3 82.3 24.1 54.9 16.1 11
0.17 72 22.2 106.3 31.2 49.9 14.6 7.8 100.8 29.5 47.9 14 8.9 94.8 27.8 45.7 13.4 10 92.7 27.2 45 13.2 10.4 88.7 26 43.6 12.8 11.1
105 3400 62 16.7 96.6 28.3 89.3 26.2 7.7 90.2 26.4 86.7 25.4 8.8 83.5 24.5 83.5 24.5 9.9 81.3 23.8 81.3 23.8 10.3 77.4 22.7 77.4 22.7 11
+ 1605 67 19.4 105.9 31 74 21.7 7.8 100.2 29.4 71.8 21 8.9 94 27.5 69.5 20.4 10 91.9 26.9 68.7 20.2 10.4 87.3 25.6 67.1 19.7 11.1
105A 0.22 72 22.2 114.1 33.4 57.8 16.9 7.8 107.7 31.6 55.7 16.3 8.9 100.6 29.5 53.4 15.6 10.1 98.2 28.8 52.6 15.4 10.5 90.8 26.6 68.4 20 10.6
4392 62 16.7 98.4 28.8 98.4 28.8 7.7 92.2 27 92.2 27 8.8 85.7 25.1 85.7 25.1 9.9 83.5 24.5 83.5 24.5 10.3 79.6 23.3 79.6 23.3 11
2073 67 19.4 109.5 32.1 83.1 24.4 7.8 103.5 30.3 81 23.7 8.9 96.1 28.2 78.4 23 10 93.4 27.4 77.5 22.7 10.4 88.6 26 75.8 22.2 11.1
0.26 72 22.2 117.6 34.5 63.5 18.6 7.8 110.8 32.5 61.3 18 9 - - - - - - - - - - - - - - -
2196 62 16.7 109.8 32.2 84.6 24.8 8.5 104.5 30.6 82 24 9.7 98.7 28.9 79.2 23.2 11.1 96.7 28.3 78.3 22.9 11.6 92.6 27.1 76.4 22.4 12.5
1036 67 19.4 118.1 34.6 71.9 21.1 8.5 112.8 33.1 69.6 20.4 9.7 107 31.4 67.1 19.7 11.2 104.9 30.8 66.2 19.4 11.6 101 29.6 64.6 18.9 12.6
0.09 72 22.2 127.7 37.4 59.4 17.4 8.5 122 35.8 57.2 16.8 9.8 115.9 34 54.8 16.1 11.2 113.7 33.3 54 15.8 11.7 109.6 32.1 52.4 15.4 12.6
120 3600 62 16.7 119.6 35.1 107.3 31.5 8.5 112.6 33 104.3 30.6 9.7 105.4 30.9 101.3 29.7 11.1 102.9 30.2 100.3 29.4 11.6 98.3 28.8 98.3 28.8 12.6
+ 1699 67 19.4 131.2 38.5 89.5 26.2 8.6 125.1 36.7 87.1 25.5 9.8 118.5 34.7 84.6 24.8 11.2 116.2 34.1 83.8 24.5 11.7 111.7 32.7 82.1 24.1 12.6
120A 0.13 72 22.2 141.5 41.5 70.7 20.7 8.7 134.8 39.5 68.3 20 9.9 127.7 37.4 65.9 19.3 11.3 125.3 36.7 65.1 19.1 11.8 120.7 35.4 63.6 18.6 12.7
4392 62 16.7 121.7 35.7 118.6 34.8 8.5 114.9 33.7 114.9 33.7 9.7 107.9 31.6 107.9 31.6 11.2 105.4 30.9 105.4 30.9 11.6 100.9 29.6 100.9 29.6 12.6
2073 67 19.4 135.5 39.7 98.3 28.8 8.6 129.1 37.8 95.9 28.1 9.9 121.9 35.7 93.2 27.3 11.3 118.9 34.9 92.1 27 11.7 113.4 33.2 90.1 26.4 12.6
0.14 72 22.2 145.8 42.7 76.1 22.3 8.7 138.8 40.7 73.8 21.6 10 131.5 38.5 71.4 20.9 11.4 - - - - - - - - - -
Table 4

8
SKM Split Air Conditioners
AUMR + CADX-A Series - R-410A
GROSS CAPACITY RATINGS
AFR Condenser Entering Air Temperature
AUMR EWB 95°F (35°C) 105°F (40.6°C) 115°F (46.1°C) 118.4°F (48°C) 125°F (51.7°C)
cfm
+
CADX-A l/s Total Capacity Sensible Capacity PI* Total Capacity Sensible Capacity PI* Total Capacity Sensible Capacity PI* Total Capacity Sensible Capacity PI* Total Capacity Sensible Capacity PI*
(BPF) °F °C MBh kW MBh kW kW MBh kW MBh kW kW MBh kW MBh kW kW MBh kW MBh kW kW MBh kW MBh kW kW
3208 62 16.7 134 39.3 106.7 31.3 10.9 127.1 37.3 103.6 30.4 12.3 119.8 35.1 100.3 29.4 14 116.7 34.2 98.9 29 14.5 110.8 32.5 96.3 28.2 15.6
1514 67 19.4 144.1 42.2 89.8 26.3 11.1 137.2 40.2 87 25.5 12.6 129.8 38 84 24.6 14.2 127.3 37.3 83 24.3 14.7 122.3 35.8 81 23.7 15.8
0.17 72 22.2 155.4 45.5 72.9 21.4 11.3 147.9 43.3 70.2 20.6 12.8 140 41 67.3 19.7 14.4 137.2 40.2 66.4 19.5 14.9 131.8 38.6 64.4 18.9 15.9
150 4800 62 16.7 141.3 41.4 128.6 37.7 11 132.5 38.8 125 36.6 12.5 123.8 36.3 121.4 35.6 14.1 120.9 35.4 120.2 35.2 14.6 115.3 33.8 115.3 33.8 15.6
+ 2265 67 19.4 154 45.1 106.4 31.2 11.2 146.3 42.9 103.5 30.3 12.7 138.2 40.5 100.5 29.5 14.3 135.4 39.7 99.5 29.2 14.9 129.9 38.1 97.5 28.6 15.9
150A 0.22 72 22.2 165.6 48.5 83.3 24.4 11.4 157.2 46.1 80.5 23.6 12.9 148.3 43.5 77.6 22.7 14.5 145.2 42.6 76.6 22.4 15.1 139.2 40.8 74.6 21.9 16.1
6417 62 16.7 144.1 42.2 144.1 42.2 11.1 135.6 39.8 135.6 39.8 12.5 127.1 37.3 127.1 37.3 14.1 124.3 36.4 124.3 36.4 14.7 118.8 34.8 118.8 34.8 15.7
3028 67 19.4 159.9 46.9 121.4 35.6 11.3 151.8 44.5 118.5 34.7 12.8 142.4 41.7 115.2 33.8 14.4 138.8 40.7 114 33.4 15 132 38.7 111.6 32.7 15.9
0.26 72 22.2 171.5 50.3 92.7 27.2 11.4 162.6 47.6 89.8 26.3 12.9 - - - - - - - - - - - - - - -
4604 62 16.7 161.4 47.3 137.4 40.3 12.7 151.7 44.5 133.1 39 14.6 141.2 41.4 128.7 37.7 16.6 137.8 40.4 127.2 37.3 17.3 131.4 38.5 124.6 36.5 18.5
2173 67 19.4 174.8 51.2 114.6 33.6 13 166.2 48.7 111.2 32.6 15 157 46 107.7 31.6 17 153.9 45.1 106.5 31.2 17.7 148 43.4 104.3 30.6 18.8
0.19 72 22.2 188.6 55.3 91.4 26.8 13.4 179.1 52.5 88.1 25.8 15.4 169.3 49.6 84.7 24.8 17.3 166 48.6 83.6 24.5 17.9 159.7 46.8 81.5 23.9 19
180 6200 62 16.7 165.5 48.5 158 46.3 12.8 155.5 45.6 153.9 45.1 14.7 145.5 42.7 145.5 42.7 16.7 142.2 41.7 142.2 41.7 17.4 135.9 39.8 135.9 39.8 18.6
+ 2926 67 19.4 183.1 53.7 130.7 38.3 13.3 173.8 50.9 127.3 37.3 15.2 164.1 48.1 123.8 36.3 17.2 160.5 47 122.5 35.9 17.8 152.8 44.8 119.8 35.1 18.9
180A 0.22 72 22.2 196.7 57.7 101.4 29.7 13.7 186.6 54.7 98.1 28.8 15.6 176.3 51.7 94.8 27.8 17.5 172.9 50.7 93.7 27.5 18.1 171.4 50.2 93.2 27.3 18.3
7792 62 16.7 168.5 49.4 168.5 49.4 12.8 158.8 46.5 158.8 46.5 14.8 148.8 43.6 148.8 43.6 16.8 145.5 42.6 145.5 42.6 17.5 139.2 40.8 139.2 40.8 18.7
3677 67 19.4 188.4 55.2 145.4 42.6 13.4 178.6 52.4 141.9 41.6 15.4 166.5 48.8 137.7 40.4 17.2 162.5 47.6 136.3 40 17.8 155.1 45.4 133.7 39.2 18.9
0.26 72 22.2 201.9 59.2 110.5 32.4 14 191.4 56.1 107.2 31.4 15.8 - - - - - - - - - - - - - - -
6292 62 16.7 187.3 54.9 173.4 50.8 13.9 177.1 51.9 169.2 49.6 15.7 166.7 48.9 164.9 48.3 17.6 163.2 47.8 163.2 47.8 18.3 156.4 45.9 156.4 45.9 19.5
2969 67 19.4 208.8 61.2 145 42.5 14.2 198.8 58.3 141.2 41.4 16 187.3 54.9 136.9 40.1 18 182.9 53.6 135.3 39.7 18.6 174.6 51.2 132.2 38.8 19.8
0.19 72 22.2 224.2 65.7 113.4 33.2 14.5 213.2 62.5 109.7 32.1 16.3 202.1 59.2 106 31.1 18.2 - - - - - - - - - -
215 7200 62 16.7 189.9 55.7 185.8 54.4 13.9 179.7 52.7 179.7 52.7 15.7 169.3 49.6 169.3 49.6 17.7 165.8 48.6 165.8 48.6 18.3 159 46.6 159 46.6 19.5
+ 3398 67 19.4 213 62.4 154.3 45.2 14.3 201.9 59.2 150.2 44 16.1 189 55.4 145.5 42.6 18 184.6 54.1 144 42.2 18.6 176.5 51.7 141.1 41.3 19.8
215A 0.2 72 22.2 228.2 66.9 119.2 34.9 14.5 217 63.6 115.5 33.9 16.4 - - - - - - - - - - - - - - -
10649 62 16.7 197.6 57.9 197.6 57.9 14 187.2 54.9 187.2 54.9 15.8 176.5 51.7 176.5 51.7 17.8 172.9 50.7 172.9 50.7 18.4 165.8 48.6 165.8 48.6 19.6
5026 67 19.4 219.4 64.3 185.3 54.3 14.4 206.8 60.6 181 53 16.2 194.3 57 176.7 51.8 18.1 190.2 55.7 175.3 51.4 18.7 182.3 53.4 172.5 50.6 19.9
0.26 72 22.2 - - - - - - - - - - - - - - - - - - - - - - - - -
6292 62 16.7 213.4 62.5 184.6 54.1 15.1 200.1 58.6 178.9 52.4 17.2 186.4 54.6 173.1 50.7 19.5 181.8 53.3 171.2 50.2 20.3 173.3 50.8 167.6 49.1 21.8
2969 67 19.4 232 68 153.9 45.1 15.4 220.7 64.7 149.5 43.8 17.5 208.4 61.1 144.8 42.5 19.9 204.1 59.8 143.3 42 20.7 196.2 57.5 140.3 41.1 22.2
0.19 72 22.2 249.9 73.3 122.2 35.8 15.6 237.4 69.6 117.9 34.6 17.8 224.3 65.7 113.4 33.2 20.3 219.8 64.4 111.9 32.8 21.1 211.5 62 109.1 32 22.6
240 8000 62 16.7 217.2 63.7 206.7 60.6 15.1 204.5 59.9 201.5 59 17.2 191.2 56 191.2 56 19.6 186.7 54.7 186.7 54.7 20.4 178.3 52.3 178.3 52.3 21.9
+ 3776 67 19.4 240.7 70.6 171.3 50.2 15.5 228.7 67 166.8 48.9 17.7 215.7 63.2 162.1 47.5 20.1 210.3 61.6 160.1 46.9 20.8 200.2 58.7 156.5 45.9 22.3
240A 0.22 72 22.2 258.3 75.7 132.9 39 15.7 245.2 71.9 128.6 37.7 18 231.7 67.9 124.2 36.4 20.4 227.1 66.6 122.8 36 21.3 - - - - -
10649 62 16.7 222.6 65.2 222.6 65.2 15.2 210.1 61.6 210.1 61.6 17.3 196.9 57.7 196.9 57.7 19.7 192.4 56.4 192.4 56.4 20.5 183.9 53.9 183.9 53.9 22
5026 67 19.4 249.5 73.1 195.9 57.4 15.6 235.1 68.9 190.9 55.9 17.8 219.2 64.2 185.3 54.3 20.1 213.9 62.7 183.4 53.8 20.9 204.2 59.8 180.1 52.8 22.4
0.26 72 22.2 266.6 78.1 148.1 43.4 15.9 - - - - - - - - - - - - - - - - - - - -
6292 62 16.7 269.2 78.9 218.8 64.1 20.3 254 74.4 211.8 62.1 23.4 234.5 68.7 203 59.5 26.7 227.9 66.8 200.1 58.6 27.8 215.7 63.2 194.7 57.1 29.8
2969 67 19.4 290.5 85.1 184.2 54 20.7 274.9 80.6 177.7 52.1 23.8 258.2 75.7 170.9 50.1 27.2 252.4 74 168.6 49.4 28.3 241.5 70.8 164.2 48.1 30.3
0.1 72 22.2 313.1 91.8 149 43.7 21.2 296.2 86.8 142.7 41.8 24.3 278 81.5 136.2 39.9 27.7 271.8 79.7 134 39.3 28.8 260.1 76.2 129.8 38.1 30.7
300 8000 62 16.7 279.2 81.8 245.8 72.1 20.5 260.1 76.2 237.6 69.6 23.5 241 70.6 229.5 67.3 26.8 234.7 68.8 226.9 66.5 27.9 223 65.4 222 65.1 29.9
+ 3776 67 19.4 304.8 89.3 205.1 60.1 21 287.9 84.4 198.5 58.2 24.1 270 79.2 191.7 56.2 27.5 264 77.4 189.4 55.5 28.6 251 73.6 184.5 54.1 30.5
300A 0.12 72 22.2 327.7 96.1 162.3 47.6 21.4 309.1 90.6 155.8 45.7 24.6 289.6 84.9 149.1 43.7 28 283.1 83 146.9 43.1 29.1 270.9 79.4 142.8 41.9 31
10649 62 16.7 286.3 83.9 283.9 83.2 20.6 268.1 78.6 268.1 78.6 23.7 249.5 73.1 249.5 73.1 27 243.2 71.3 243.2 71.3 28.1 231.4 67.8 231.4 67.8 30.1
5026 67 19.4 319 93.5 234.7 68.8 21.3 300.8 88.1 227.9 66.8 24.4 278 81.5 219.6 64.4 27.7 270.4 79.3 217 63.6 28.7 256.5 75.2 212 62.1 30.6
0.14 72 22.2 341.5 100.1 180.6 52.9 21.7 321.6 94.3 174.1 51 24.9 - - - - - - - - - - - - - - -
Table 5
Notes:
1. See Page 2 for legend.
2. Ratings are based on 80°F (27°C) DB evaporator air entering temperature.
3. Direct interpolation is permissible. Do not extrapolate.
4. SKM Computer Selection Software are available for quick and accurate selections.
5. Shaded area in gray are at 120°F (49°C) condenser entering air temperature.
6. Capacity is gross capacity which does not include the effect of evaporator fan motor heat.
* Power input mentioned in this page should not be used for cable or fuse selection. MCA and MFA values given in the electrical data
(page 11) should be referred for the same.

9
 SKM Split Air Conditioners
AUMR + CADX-A Series - R-410A
Fan Performance
Internal Static External Static Pressure - in.wg(Pa)
AirFlowRate RPM
AUMR + CADX Pressure 0.2(50) 0.4(100) 0.5(125) 0.6(150) 0.8(200) 1.0(250) 1.25(313)
Range
cfm l/s in.wg Pa RPM kW RPM kW RPM kW RPM kW RPM kW RPM kW RPM kW
1597 754 0.24 59.75 630 0.18 736 0.23 785 0.25 833 0.28 926 0.33 1017 0.39 1129 0.47 869
060 + 060A 2000 944 0.36 90.18 731 0.31 821 0.37 863 0.4 905 0.43 984 0.5 1060 0.56 1153 0.65 to
1084
3193 1507 0.96 239.18 1085 1.15 1145 1.24 1175 1.29 1204 1.34 1261 1.43 1315 1.53 1382 1.65
1597 754 0.24 59.75 630 0.18 736 0.23 785 0.25 833 0.28 926 0.33 1017 0.39 1129 0.47 928
070 + 070A 2400 1133 0.53 131.35 844 0.51 922 0.58 960 0.62 996 0.66 1066 0.73 1133 0.8 1214 0.9 to
1157
3193 1507 0.96 239.18 1085 1.15 1145 1.24 1175 1.29 1204 1.34 1261 1.43 1315 1.53 1382 1.65
2196 1036 0.24 59.71 - - 656 0.32 699 0.35 740 0.39 818 0.46 893 0.54 982 0.64
090 +090A 3000 1416 0.43 107.54 700 0.55 774 0.65 809 0.69 843 0.74 908 0.83 970 0.93 1045 1.05
4392 2073 0.96 239.14 973 1.6 1026 1.74 1052 1.8 1077 1.87 1127 2.01 1176 2.15 1234 2.32 780
to
2196 1036 0.24 59.71 - - 656 0.32 699 0.35 740 0.39 818 0.46 893 0.54 982 0.64 973
100 + 100A 3400 1604 0.56 139.76 776 0.78 843 0.88 875 0.94 906 0.99 966 1.1 1024 1.2 1092 1.33
4392 2073 0.96 239.14 973 1.6 1026 1.74 1052 1.8 1077 1.87 1127 2.01 1176 2.15 1234 2.32
2196 1036 0.24 59.71 - - 656 0.32 699 0.35 740 0.39 818 0.46 893 0.54 982 0.64
782
105 + 105A 3400 1604 0.56 139.76 776 0.78 843 0.88 875 0.94 906 0.99 966 1.1 1024 1.2 1092 1.33 to
4392 2073 0.96 239.14 973 1.6 1026 1.74 1052 1.8 1077 1.87 1127 2.01 1176 2.15 1234 2.32 975

2196 1036 0.28 69.69 - - 674 0.33 716 0.37 756 0.4 834 0.48 907 0.55 996 0.66 882
120 + 120A 3600 1699 0.74 185.52 851 0.97 913 1.09 942 1.14 972 1.2 1028 1.31 1082 1.42 1148 1.56 to
1099
4392 2073 1.13 282.67 1019 1.72 1071 1.86 1096 1.92 1121 1.99 1170 2.13 1217 2.27 1274 2.44
3208 1514 0.24 59.71 472 0.35 549 0.45 585 0.5 619 0.55 683 0.65 744 0.76 817 0.92 670
150 + 150A 4800 2265 0.52 130.04 632 1 690 1.14 717 1.21 744 1.27 795 1.42 844 1.56 902 1.75 to
835
6417 3028 0.96 239.21 816 2.29 861 2.46 882 2.55 904 2.64 946 2.82 966 2.91 1034 3.24
4604 2173 0.29 71.1 621 0.62 714 0.78 758 0.86 799 0.93 879 1.09 955 1.26 1045 1.49 785
180 + 180A 6200 2926 0.53 132.42 781 1.37 855 1.58 891 1.68 925 1.79 991 1.99 1054 2.2 1129 2.47 to
979
7792 3677 0.87 215.67 954 2.6 1015 2.86 1044 2.99 1073 3.12 1129 3.39 1183 3.65 1249 3.97
6292 2969 0.29 71.09 513 0.77 593 0.98 629 1.08 665 1.19 732 1.42 796 1.67 873 2 600
215 + 215A 7200 3398 0.38 93.5 565 1.09 637 1.32 671 1.44 703 1.56 765 1.81 824 2.07 895 2.41 to
748
10649 5025 0.87 215.67 785 3.23 837 3.55 863 3.72 887 3.88 935 4.22 981 4.56 1036 5.01
6292 2969 0.29 71.09 513 0.77 593 0.98 629 1.08 665 1.19 732 1.42 796 1.67 873 2
240 + 240A 8000 3775 0.47 117 614 1.45 680 1.7 712 1.83 742 1.96 800 2.22 855 2.5 921 2.87
10649 5025 0.87 215.67 785 3.23 837 3.55 863 3.72 887 3.88 935 4.22 981 4.56 - - 672
to
6292 2969 0.34 84.79 536 0.83 613 1.03 649 1.14 683 1.25 750 1.49 813 1.74 889 2.08 838
300 + 300A 8000 3775 0.56 139.89 645 1.56 709 1.82 740 1.95 769 2.08 826 2.35 880 2.64 945 3.01
10649 5025 1.04 259.21 831 3.51 881 3.84 905 4.01 929 4.18 975 4.52 1020 4.87 - -
Table 6

Notes:

1. Areas shaded in blue indicate factory setting of RPM.

2. Areas shaded in grey indicate operating range outside the standard motor. Shift to larger motor size in this area.
3. Internal static pressure is based on pressure drops through evaporator coil, fan casing and 1” flat filter.
4. The shown RPM range is with standard pulleys combination.

10
 SKM Split Air Conditioners
AUMR + CADX-A Series - R-410A
Typical Wiring Diagram
Typical Wiring
AUMR Models Diagram
: 060 ~ 100
AUMR Models : 060 - 100
Typical Wiring Diagram
PTB * POWER SUPPLY ( V/Ph/Hz )
* * L1
L2
L3
AUMR Models : 060 ~ 100 LEGEND
N
C2
C1
FIELD WIRING & FIELD SUPPLIED DEVICES
PTB * POWER SUPPLY ( V/Ph/Hz
OL
) PTB POWER TERMINAL BLOCK
* * L1
LEGEND
R Y B
L2
L3 FIELD WIRING C CONTACTOR
N ( BY OTHERS )
T3C1
C2 CM COMPRESSOR MOTOR
T1 T2 FIELD WIRING & FIELD SUPPLIED DEVICES
OL
PTB CFMTERMINAL
POWER CONDENSER
BLOCK FAN MOTOR
CM CFM
R Y B
FIELD WIRING C OL ROVERLOAD RELAY
CONTACTO
( BY OTHERS )
OL

EFM EVAPORATOR FAN MOTOR

HPS

LPS
T1
T3
T2
CM COMPRESSOR MOTOR
CS
CM CFM THERMOSTAT ( BY OTHERS )
CFM MCB MINIATURE
CONDENSER FAN MOTOR CIRCUIT BREAKER
C R G Y OL OVERLOAD
CCH RELAY
CRANK CASE HEATER
EFM
OL

EFM EVAPORATOR FAN MOTOSWITCH

R
HPS

HP 2LPS

CS CONTROL
ON / OFF

HP 1

LP 1

LP 2
(ON / OFF)

(LP 1)

(LP 2)
(HP 1)

(HP 2)

CS
CADX - A
MCB MINIATURE CIRCUIT BREAKER
THERMOSTAT ( BY OTHERS )
HPS HIGH PRESSURE SWITCH
C R G Y
EFM
CCH CRANK CASE HEATER
(HP 1) RLY1

LPS LOW PRESSURE SWITCH

R

CS CONTROL SWITCH
C
ON / OFF
FAN2

HP 1

HP 2

LP 1

LP 2
(ON / OFF)

(LP 1)

(LP 2)
(HP 2)
OUT

TFR TRANSFORMER
RLY2

CADX - A
G

MCB HPS HIGH PRESSURE SWITCH

W2 W1 Y2 Y1
FAN1
OUT

6A
LOWCTB CONTROL
SWITCHTERMINAL BLOCK
CTB
RLY3
RLY1

LPS PRESSURE
R

C1
C
X2
FAN2
OUT

ECB ELECTRONIC CONTROL BOARD

RLY4

TFR TRANSFORMER
RLY2

MCB
W2 W1 Y2 Y1
X1
FAN1
OUT

6A
CTB
CTB CONTROL TERMINAL BLOCK
RLY3
RLY5

*
TYPICAL WIRING DIAGRAM SHOWN IS SUITABLE FOR 380/3Ph/60Hz ONLY.
HTR2

C1
X2

P-COM1

ECB ELECTRONIC CONTROL BOARD

RLY4
RLY6

FOR 460V/3Ph/60Hz AND 220V/3Ph/60Hz , PLEASE CONSULT SKM.

HTR2 HTR1

ECB
X1

RLY5
RLY7

* TYPICAL WIRING DIAGRAM SHOWN IS SUITABLE FOR 380/3Ph/60Hz ONLY.

HTR1 INFAN

P-COM1

** PROVIDE OVERCURRENT,
220V/3Ph/60Hz EARTH
, PLEASEFAULT PROTECTION, SHORT CIRCUIT AND
RLY6

FOR 460V/3Ph/60Hz AND CONSULT SKM.

OD

ECB
RLY8

DISCONNECT MEANS AS REQUIRED BY LOCAL & NATIONAL ELECTRIC CODE.

CM1 P1CM2 P2 P1INFAN P2

RLY7

1234

(BY OTHERS)
** PROVIDE OVERCURRENT, EARTH FAULT PROTECTION, SHORT CIRCUIT AND
RLY9

OD

ID
RLY8

S1

DISCONNECT MEANS AS REQUIRED BY LOCAL & NATIONAL ELECTRIC CODE.

RLY11 RLY10

1234

(BY OTHERS)
RLY9
CCH

ID
S1
RLY11 RLY10
CM2
CCH

CM+ CFM

L1
CM1

T5A L250V
EFM

F1

SEC1
CM+ CFM

N1
PRI1
L1

T5A L250V

C2 C1
EFM

F1

SEC1
N1
PRI1

C2 C1 CONTROL CIRCUIT
BLACK
10V

CONTROL CIRCUIT RED BLACK

220V

BLACK
10V

WHITE
24V

RED
RED BLACK
220V

TFR WHITE WHITE

24V

RED

TFR WHITE

AUMR
AUMR Models
AUMR Models:: :105
Models 105
105 ~
~ 300
300
- 300
PTB PTB * PO
* WER SUPPLY
POWER ( V/Ph/Hz
SUPPLY ( V/Ph/Hz))
* * L1 * * L1
LEGEND LEGEND
L2 L2
L3 L3
N N
C5
C5
C3 C4 FIELD WIRING & FIELD SUPPLIED DEVICES
C1
C1
C2
C2 C3 C4
OL
FIELD WIRING & FIELD SUPPLIED DEVICES
OL PTB POWER TERMINAL BLOCK
R Y B PTB POWER TERMINAL BLOCK
R Y B
C CONTACTOR
C CONTACTOR
T3 T3 R Y B
T1 T2 T1 T2
FIELD WIRING
CM COMPRESSOR MOTOR
T3 T3 R Y B
T1 T2 T1 T2 ( BY OTHERS ) WIRING
FIELD
CM1 CM2 CFM1 CFM2
( BY OTHERS )
CFM
CM COMPRESSOR MOTOR
CONDENSER FAN MOTOR
CM1 CM2 CFM1 CFM2
OL CFMRELAY
OVERLOAD CONDENSER FAN MOTOR
EFM OL FAN
EVAPORATOR OVERLOAD
MOTOR RELAY
OL HPS1

HPS2

LPS1

LPS2
OL

MCB EFM CIRCUIT

MINIATURE EVAPORATOR
BREAKER FAN MOTOR
CS
HPS1

HPS2

LPS1

LPS2

THERMOSTAT ( BY OTHERS ) CCH CRANKMCB

CASE HEATER
MINIATURE CIRCUIT BREAKER
CS C R G Y1 Y2 EFM CS CONTROL
CCHSWITCH
CRANK CASE HEATER
THERMOSTAT ( BY OTHERS )
G CADX - A HPS HIGH PRESSURE SWITCH
ON / OFF

C R Y1 Y2 EFM CS CONTROL SWITCH

LP 1

LP 2
HP 1

HP 2
(ON / OFF)

(HP 1)

(HP 2)

(LP 1)

(LP 2)

LPS LOW PRESSURE SWITCH

CADX - A HPS HIGH PRESSURE SWITCH
ON / OFF

LP 1

LP 2
HP 1

HP 2
(ON / OFF)

(HP 1)

(HP 2)

(LP 1)

(LP 2)
RLY1

TFR TRANSFORMER
R

LPS LOW PRESSURE SWITCH

C
FAN2
OUT

CTB CONTROL TERMINAL BLOCK

RLY2

MCB
6A
RLY1

W2 W1 Y2 Y1

TFR CONTRO
TRANSFORMER
FAN1
OUT

ECB ELECTRONIC L BOARD

RLY3

C1 C2
FAN2

CTB
OUT

CTB CONTROL TERMINAL BLOCK

RLY2
X2

MCB
RLY4

6A
W2 W1 Y2 Y1

* TYPICAL WIRING DIAGRAM SHOWN IS SUITABLE FOR 380/3Ph/60Hz ONLY.

FAN1
OUT
X1

ECB ANDELECTRONIC
220V/3Ph/60HzCONTRO L BOARDSKM.
RLY3
RLY5

FOR 460V/3Ph/60Hz , PLEASE CONSULT

FCS1

FCS2

C1 C2 CTB
INFAN HTR1 HTR2

P-COM1
X2

RLY4
RLY6

ECB
** * TYPICAL EARTH
PROVIDE OVERCURRENT, WIRING DIAGRAM
FAULT SHOWN
PROTECTION, IS SUITABLE
SHORT FOR 380/3Ph/60Hz ONLY.
CIRCUIT AND
X1

RLY7

RLY5

DISCONNECT MEANS AS REQUIRED BY LOCAL

FOR 460V/3Ph/60Hz & NATIONAL ELECTRIC
AND 220V/3Ph/60Hz CODE.
, PLEASE CONSULT SKM.
FCS1

FCS2

INFAN HTR1 HTR2

OD

P-COM1

(BY OTHERS)
RLY8

RLY6
P2

ECB
** PROVIDE OVERCURRENT, EARTH FAULT PROTECTION, SHORT CIRCUIT AND
1234
RLY9
P1

RLY7

ID

DISCONNECT MEANS AS REQUIRED BY LOCAL & NATIONAL ELECTRIC CODE.

S1
RLY11 RLY10
CM2

OD

(BY OTHERS)
RLY8
P2
CCH1

CCH2

CM1

1234
RLY9
P1

ID
L1

T5A L250V

S1
CFM1
CFM2

CM2

CM1
EFM

F1

RLY11 RLY10
CM2

SEC1
N1
PRI1

C4 C3 C5 C2 C1
CCH1

CCH2

CM1

CONTROL CIRCUIT
BLACK
10V
L1

T5A L250V

RED
CFM1

BLACK
CFM2

220V
CM2

CM1
EFM

F1

WHITE
24V

SEC1

RED
N1
PRI1

TFR WHITE

C4 C3 C5 C2 C1

CONTROL CIRCUIT
BLACK
10V

RED BLACK
220V

WHITE
24V

RED

TFR WHITE

11
 DATA
AUMR + CADX-A
SKM Split Air Conditioners
AUMR + CADX-A Series - R410A
ELECTRICAL Series - R410A
ELECTRICAL
AUMR DATA
+ CADX-A
AUMR + CADX-A Series
Series - R410A
Power-Supply:
R-410A380V/3Ph/60Hz

ELECTRICAL
Model DATA
Unit Characteristic Compressor Condenser Fan Motor Power Supply:
Model 380V/3Ph/60Hz
Evapoartor Fan Motor
ELECTRICAL
AUMR DATA CADX
Model MFA Unit Characteristic
MCA ICF QTY Compressor
RLA LRA FLAFan MotorLRA Power
QTYCondenser Supply:Evapoartor
Model 380V/3Ph/60Hz
FLA FanLRA
Motor
AUMR
060 25 15 99 1 10 94 1 1.0 3.0 CADX
060-A 1.5 5.8
Model MFA Unit Characteristic
MCA ICF QTY Compressor
RLA LRA QTYCondenser
FLAFan MotorLRA Model Evapoartor
FLA FanLRA Motor
070 32 18 93 1 12 88 1 1.0 3.0 070-A 1.9 7.8
AUMR
060 25 15 99 CADX
060-A
090 50
MFA 25
MCA 108
ICF 11
QTY
10
16
RLA
94
94
LRA
11
QTY
1.0
2.8
FLA
3.0
11.0
LRA 090-A 1.5
2.4
FLA
5.8
10.6
LRA
070
100 32
50 18
29 93
136 11 12
19 88
123 11 1.0
2.8 3.0
11.0 070-A
100-A 1.9
2.4 7.8
10.6
060
090 25
50 15
25 99
108 1 10 94 11 1.0 3.0 060-A
090-A 1.5 5.8
105 40 25 81 1 +1 1 9 16
+9 66 94
+ 66 2 2.8
1.0 11.0
3.0 105-A 2.4
2.4 10.6
10.6
070
100 32
50 18
29 93
136 11 12 88 1 1.0 3.0 070-A
100-A 1.9 7.8
120 40 28 111 1+1 10 19
+ 10 94123
+ 94 21 2.8
1.0 11.0
3.0 120-A 2.4
3.4 10.6
14.6
090
105 50
40 25
25 108
81 1 169 6694 1 2.8 11.0 090-A
105-A 2.4 10.6
150 63 38 95 11 ++ 11 149 ++ 14 73 ++ 73
66 22 1.0
1.3 3.0
3.6 150-A 2.4
3.4 10.6
14.6
100
120 50
40 29
28 136
111 1 19 123 12 2.8 11.0 100-A
120-A 2.4 10.6
180 63 43 120 11 ++ 11 10 ++ 16
16 10 94 ++ 94
94 94 2 1.0
1.3 3.0
3.6 180-A 3.4
4.8 14.6
19.2
105
150 40
63 25
38 81
95 1+1 9 ++ 914 66 ++ 66 22 1.0 3.0 105-A
150-A 2.4 10.6
215 80 53 161 11 ++ 11 14
19 + 19 73 73
123 + 123 2 1.3
2.8 3.6
11.0 215-A 3.4
4.8 14.6
19.2
120
180 40
63 28
43 111
120 11 ++ 11 10
16 +++ 21
10
16 94
94 +++ 140
94
94 2 1.0 3.0 120-A
180-A 3.4 14.6
240 80 59 185 1+1 21 140 22 1.3
3.5 3.6
16.0 240-A 4.8
4.8 19.2
19.2
150
215 63
80 38
53 95
161 1+1 14 + 14 73 + 73 22 1.3 3.6 150-A
215-A 3.4 14.6
300 100 72 197 11 ++ 11 19 +
26 + 26 19 123 + 123
145 + 145 2 2.8
3.5 11.0
16.0 300-A 4.8
6.5 19.2
27.3
180
240 63
80 43
59 120
185 11 ++ 11 16
21 ++ 1621 94 ++ 94
140 140 22 1.3
3.5 3.6
16.0 180-A
240-A 4.8
4.8 19.2
19.2
215
300 80
100 53
72 161
197 11 ++ 11 19 +
26 + 2619 123 + 123
145 + 145 22 2.8
3.5 11.0
16.0 215-A
300-A 4.8
6.5 19.2
27.3
240 80 59 185 1+1 21 + 21 140 + 140 2 3.5 16.0 240-A 4.8 19.2
300 100 72 197 1+1 26 + 26 145 + 145 2 3.5 16.0 Power Supply: 460V/3Ph/60Hz
300-A 6.5 27.3
Table 7

Model Unit Characteristic Compressor Condenser Fan Motor Power Evapoartor

Supply:
Model Fan Motor
460V/3Ph/60Hz
AUMR CADX
Model MFA Unit Characteristic
MCA ICF QTY RLA
Compressor LRA QTYCondenser
FLAFan MotorLRA Power
Model FLA
Supply:Evapoartor FanLRA
460V/3Ph/60HzMotor
060
AUMR 32 16 80 1 11 75 1 1.0 3.0 060-A
CADX 1.5 6.4
Model MFA Unit Characteristic
MCA ICF QTY RLA
Compressor LRA QTYCondenser
FLAFan MotorLRA Model FLA FanLRA
Evapoartor Motor
070 32 18 80 1 12 75 1 1.0 3.0 070-A 1.9 9.4
060
AUMR 32 16 80 1 11 75 1 1.0 3.0 060-A
CADX 1.5 6.4
090 40
MFA 23
MCA 115
ICF 1
QTY 14
RLA 100
LRA 1
QTY 2.8
FLA 13.0
LRA 090-A 2.3
FLA 12.6
LRA
070 32 18 80 1 12 75 1 1.0 3.0 070-A 1.9 9.4
100
060 50
32 25
16 110
80 11 16
11 95
75 11 2.8
1.0 13.0
3.0 100-A
060-A 2.3
1.5 12.6
6.4
090 40 23 115 1 14 100 1 2.8 13.0 090-A 2.3 12.6
105
070 40
32 22
18 66
80 1 +1 1 812+8 5275
+ 52 21 1.0
1.0 3.0
3.0 105-A
070-A 2.3
1.9 12.6
9.4
100 50 25 110 1 16 95 1 2.8 13.0 100-A 2.3 12.6
120
090 50
40 30
23 93
115 1 +1 1 1114+ 11 75100
+ 75 21 1.0
2.8 3.0
13.0 120-A
090-A 3.2
2.3 18
12.6
105 40 22 66 1+1 8+8 52 + 52 2 1.0 3.0 105-A 2.3 12.6
150
100 50
50 35
25 96
110 1 +1 1 1316+ 13 7595
+ 75 21 1.3
2.8 3.6
13.0 150-A
100-A 3.2
2.3 18
12.6
120 50 30 93 1+1 11 + 11 75 + 75 2 1.0 3.0 120-A 3.2 18
180
105 63
40 39
22 123
66 11 ++ 11 148 ++ 14 100 + 100 22 1.3 3.6 180-A
105-A 4.4 24.7
150 50 35 96 1+1 13 + 813 52
75 ++ 52
75 2 1.0
1.3 3.0
3.6 150-A 2.3
3.2 12.6
18
215
120 63
50 46
30 131
93 11 ++ 11 16
11 + 16 95
75 ++ 95
+ 22 2.8 13.0 215-A
120-A 4.4 24.7
180 63 39 123 1+1 14 ++ 11
14 100 75
100 2 1.0
1.3 3.0
3.6 180-A 3.2
4.4 18
24.7
240
150 80
50 54
35 159
96 11 ++ 11 19
13 + 19 114 + 114 22 3.5 18.0 240-A
150-A 4.4 24.7
215 63 46 131 1+1 16 ++ 13
16 75
95 ++ 75
95 2 1.3
2.8 3.6
13.0 215-A 3.2
4.4 18
24.7
300
180 100
63 60
39 173
123 11 ++ 11 21
14 + 21 125 + 125 22 3.5 18.0 300-A
180-A 5.6 33.1
240 80 54 159 1+1 19 ++ 14
19 100 + 100
114 + 114 2 1.3
3.5 3.6
18.0 240-A 4.4
4.4 24.7
24.7
215
300 63
100 46
60 131
173 11 ++ 11 16
21 ++ 16
21 95 ++ 95
125 125 22 2.8
3.5 13.0
18.0 215-A
300-A 4.4
5.6 24.7
33.1
240 80 54 159 1+1 19 + 19 114 + 114 2 3.5 18.0 240-A 4.4 24.7
Table 8

300 100 60 173 1+1 21 + 21 125 + 125 2 3.5 300-A

18.0 Power Supply: 220V/3Ph/60Hz
5.6 33.1

Model Unit Characteristic Compressor Condenser Fan Motor Power Supply:

Model Evapoartor Fan Motor
220V/3Ph/60Hz
AUMR CADX
Model MFA Unit Characteristic
MCA ICF QTY Compressor
RLA LRA QTYCondenserFLAFan MotorLRA Power
Model FLA
Supply:Evapoartor FanLRA
220V/3Ph/60HzMotor
060
AUMR 63 33 163 1 23 155 1 1.7 5.2 060-A
CADX 2.6 9.8
Model MFA Unit Characteristic
MCA ICF QTY Compressor
RLA LRA QTYCondenserFLAFan MotorLRA Model FLA FanLRA
Evapoartor Motor
070 63 36 157 1 25 149 1 1.7 5.2 070-A 3.3 13.7
060
AUMR 63 33 163 1 23 155 1 1.7 5.2 060-A
CADX 2.6 9.8
090 80
MFA 45
MCA 185
ICF 1
QTY 28
RLA 164
LRA 1
QTY 5.4
FLA 16.7
LRA 090-A 4.2
FLA 18.5
LRA
070 63 36 157 1 25 149 1 1.7 5.2 070-A 3.3 13.7
100
060 100
63 51
33 216
163 11 33
23 195
155 11 5.4
1.7 16.7
5.2 100-A
060-A 4.2
2.6 18.5
9.8
090 80 45 185 1 28 164 1 5.4 16.7 090-A 4.2 18.5
105
070 80
63 48
36 139
157 1 +1 1 1825
+ 18 110149
+ 110 21 1.7
1.7 5.2
5.2 105-A
070-A 4.2
3.3 18.5
13.7
100 100 51 216 1 33 195 1 5.4 16.7 100-A 4.2 18.5
120
090 100
80 61
45 191
185 1 +1 1 2328
+ 23 155164
+ 155 21 1.7
5.4 5.2
16.7 120-A
090-A 5.8
4.2 24.4
18.5
105 80 48 139 1+1 18 + 18 110 + 110 2 1.7 5.2 105-A 4.2 18.5
150
100 100
100 69
51 205
216 1 +1 1 26 33
+ 26 164 + 164 21 2.3 6.9 150-A
100-A 5.8 24.4
120 100 61 191 1+1 23 + 23 155195+ 155 2 5.4
1.7 16.7
5.2 120-A 4.2
5.8 18.5
24.4
180
105 125
80 76
48 209
139 11 ++ 11 28
18 + 28 164 + 164 22 2.3 6.9 180-A
105-A 8.1 35
150 100 69 205 1+1 26 ++ 18
26 110
164 ++ 110
164 2 1.7
2.3 5.2
6.9 150-A 4.2
5.8 18.5
24.4
215
120 160
100 93
61 258
191 1 + 1
11 ++ 11 33
23 + 33 195 + 195 2 5.4 16.7 215-A
120-A 8.1 35
180 125 76 209 28 ++ 23
28 155
164 ++ 155
164 22 1.7
2.3 5.2
6.9 180-A 5.8
8.1 24.4
35
240
150 160
100 97
69 297
205 11 ++ 11 34
26 ++ 34
26 225
164 ++ 225
164 22 6.4
2.3 23.7
6.9 240-A
150-A 8.1
5.8 35
24.4
215 160 93 258 1+1 33 + 33 195 + 195 2 5.4 16.7 215-A 8.1 35
300
180 200
125 145
76 340
209 11 ++ 11 54
28 + 54 245 + 245 22 6.4 23.7 300-A
180-A 10.7 49
240 160 97 297 1+1 34 ++ 28
34 164
225 ++ 164
225 2 2.3
6.4 6.9
23.7 240-A 8.1
8.1 35
35 9
Table
Legend
215 160 93 258 1 + 1 33 + 33 195 + 195 2 5.4 16.7 215-A 8.1 35
300 200 145 340 1+1 54 + 54 245 + 245 2 6.4 23.7 300-A 10.7 49
MFA 240 Maximum
160 Fuse97Amps 297 1+1
(for fuse/circuit 34 + 34 225
breaker + 225
sizing), 2 RLA 6.4Rated 23.7 240-A (at worst
Load Amps. 8.1 operating
35 condition)
300 complies
200 with NEC
145 Article 340 440-221 + 1& 430-52.
54 + 54 245 + 245 2 LRA 6.4Locked23.7 300-A
Rotor Amps 10.7 49
MCA Minimum Circuit Amps.(for wire sizing), complies with FLA Full Load Amps
NEC article 440-33. Note :
ICF Maximum Instantaneous Current Flow Voltage imbalance not to exceed ± 2 % of the rated voltage

12
SKM Split Air Conditioners
AUMR + CADX-A Series - R-410A
Condensing Unit Dimensional Data
AUMR Models : 060
MODEL: & 070
AUMR- 060 & 070
.7
[19] LEGEND
MODEL: AUMR-1 060 & 070
2
MOUNTING HOLES
.7 Ø0.5 x 4 NOS. 1 CONDENSER COIL
[19] 1 LEGEND
A1
2 A3 MOUNTING HOLES
2 CONDENSER FAN
Ø0.5 x 4 NOS. 31 CONTROL PANEL
CONDENSER COIL
[102]
4

A1 A3 42 COMPRESSOR
CONDENSER FAN
[102]

3 CONTROL PANEL
[102]
4

ALL4DIMENSIONS
COMPRESSORARE IN INCHES [mm]
A2 A4 A1-A4 ARE LOADING POINTS
[102]
4

ALL DIMENSIONS ARE IN INCHES [mm]

A2 A4 A1-A4 ARE LOADING POINTS
28 30
[711] [762]
28 30
[711] [762]

3
3
ACCESS FOR
[1147]
45.1

[1024]
40.31

COMPRESSOR
ACCESS FOR
POWER SOURCE
[1147]

SUC.Ø
45.1

[1024]
40.31

COMPRESSOR
HOLE Ø1 [25]
SUC.Ø POWER SOURCE
HOLE Ø1 [25] CIRCUIT
CONTROL
LIQ.Ø
HOLE Ø0.75
CONTROL [19]
CIRCUIT
LIQ.Ø
HOLE Ø0.75 [19]

4 8 2
4 8 2
[50]

[203] [50]
2

[50]

[203] [50]
2

AUMR Models :MODELS:

090AUMR-
MODELS: & 100090090
AUMR- & 100
& 100
.7 .7
1 2 2
[19] 1 2 2
[19]
[51] [51] LEGEND
LEGEND

A3 A3 CONDENSER COIL
11 CONDENSER COIL
A1 A1
CONDENSER FAN
22 CONDENSER FAN
[102]
[102]

CONTROL PANEL
33 CONTROL
4

PANEL
4

4 COMPRESSOR
4 COMPRESSOR
ALL DIMENSIONS ARE IN INCHES [mm]
MOUNTING HOLES ALL DIMENSIONS ARE IN INCHES [mm]
[102]

MOUNTING HOLES A1-A4 ARE LOADING POINTS

4

Ø0.5 x 4 NOS.
[102]

A1-A4 ARE LOADING POINTS

4

Ø0.5
A4
x 4 NOS.
A2
A2 A4

38 38
38 [965] [965]
38
[965] [965]

3
[1024] [1219]
40.31 47.99

POWER SOURCE
[1024]
40.31

SUC.Ø HOLE Ø1[25]

LIQ.Ø
[1219]
47.99

POWER CIRCUIT
CONTROL SOURCE
SUC.Ø HOLE
HOLE Ø1[25]
Ø0.75 [19]
LIQ.Ø CONTROL CIRCUIT
HOLE Ø0.75 [19]

4 ACCESS FOR
11 2
[50]

COMPRESSOR
2

[279] [50]
4 ACCESS FOR
11 2
[50]

COMPRESSOR
2

[279] [50]

13
 SKM Split Air Conditioners
AUMR + CADX-A Series - R-410A
MODEL: AUMR- 105 & 120

.7
MOUNTING HOLES
[19] Ø0.5 x 4 NOS. LEGEND
Condensing Unit Dimensional
A1
Data A3 1 CONDENSER COIL
MODEL: AUMR- 105 & 120
AUMR Models : 105 & 120

[102]
2 CONDENSER FAN

4
2 .7 3 CONTROL PANEL
MOUNTING HOLES
[19] Ø0.5 x 4 NOS. LEGEND 4 COMPRESSOR
A3 1 CONDENSER COIL
A1 ALL DIMENSIONS ARE IN INCHES [mm]

[102]
2 CONDENSER
A1-A4 AREFAN
LOADING POINTS
4 2 3 CONTROL PANEL
ACCESS 4 COMPRESSOR

ALL DIMENSIONS ARE IN INCHES [mm]

A1-A4 ARE LOADING POINTS
1
ACCESS
[102]
4

A2 A4

1
43
[102]

74
4

A2 [1092] A4
[1880]
AIR OUT
3
43
74
[1092]
[1880]
AIR OUT
3

AIR IN
[1147]

[1024]
40.31
45.1

AIR IN
[1147]

[1024]
40.31
45.1

[366]
14.4
[366]
14.4

4
[102]

SUC. Ø#1 ACCESS SUC. Ø#2

[50]

4
2

LIQ. Ø#1 4 LIQ. Ø#2

POWER SOURCE
[102]

SUC. Ø#1 ACCESS SUC. Ø#2

[50]

HOLE Ø1 [25]
4
2

CONTROL CIRCUIT
LIQ. Ø#1 POWER SOURCE LIQ. Ø#2 HOLE Ø0.75 [19]
HOLE Ø1 [25] CONTROL CIRCUIT
HOLE Ø0.75 [19]

AUMR Models : 150

MODEL: & 180
AUMR- 150 & 180
MODEL: AUMR- 150 & 180
LEGEND
[254]
10 10

A1 LEGEND
[254]

A3
A1 A3
1 CONDENSER COIL
4-Ø0.79 [20] HOLES 1 CONDENSER COIL
4-Ø0.79 [20] HOLES 2 CONDENSER
2 CONDENSER
FOR ANCHOR BOLTS FAN
FAN
FOR ANCHOR BOLTS
22 3 CONTROL
3 CONTROL PANEL PANEL
4 COMPRESSOR
4 COMPRESSOR

ALL DIMENSIONS
ALL DIMENSIONS ARE IN
ARE IN INCHES INCHES [mm]
[mm]
ACCESS
ACCESS A1-A4 ARE LOADING
A1-A4 POINTS POINTS
ARE LOADING

1
1A2
A4
A2 A4
[254]
10 10
[254]

74
43 [1880] 74
[1092]43
[1880]
AIR OUT
[1092] 3
AIR OUT
3

AIR IN
[1024] [1024]
[1220]

40.31 40.31
48

AIR IN
[1220]
48

[416]
16.4

[416]
16.4

SUC. Ø#1 4 ACCESS SUC. Ø#2

RIGGING HOLES
[100]

[152]
3.94

Ø0.79 [20] x 4Nos. LIQ. Ø#1 LIQ. Ø#2

6

POWER SOURCE
HOLE Ø1 [25] CONTROL CIRCUIT
SUC. Ø#1 4 ACCESS SUC. Ø#2
HOLE Ø0.75 [19]
RIGGING HOLES
[100]

[152]
3.94

Ø0.79 [20] x 4Nos. LIQ. Ø#1 LIQ. Ø#2

6

POWER SOURCE
HOLE Ø1 [25] CONTROL CIRCUIT
HOLE Ø0.75 [19]

14
 SKM Split Air Conditioners
AUMR + CADX-A Series - R-410A
Condensing Unit Dimensional Data
MODEL: AUMR- 215
AUMR Model : 215
LEGEND

[254]
10
A1 A3
1 CONDENSER COIL
MODEL: AUMR- 215 4-Ø0.79 [20] HOLES 2 CONDENSER FAN
2
FOR ANCHOR BOLTS 3 CONTROL PANEL
LEGEND 4 COMPRESSOR

[254]
10 A1 A3
1 CONDENSER COIL
ALL DIMENSIONS ARE IN INCHES [mm]
4-Ø0.79 [20] HOLES 2 CONDENSER FAN
A1-A4 ARE LOADING POINTS
2
FOR
3 ANCHOR BOLTS 3 CONTROL PANEL
ACCESS
4 COMPRESSOR

ALL DIMENSIONS ARE IN INCHES [mm]

A1-A4 ARE LOADING POINTS
1 3
ACCESS
A4
A2
[254]
10

1
43 A4
74
A2 [1092]
[254]

[1880]
10

AIR OUT

43
74
[1092]
[1880]
AIR OUT

AIR IN
[1276]

[1024]
50.2

40.31

AIR IN
[1276]

[1024]
50.2

40.31

[213]
8.4

4
[213]

SUC. Ø#1 ACCESS SUC. Ø#2

8.4

RIGGING HOLES
[100] [100]

[152]
3.94 3.94

LIQ. Ø#1 LIQ. Ø#2

6

Ø0.79 [20] x 4Nos. 4 POWER SOURCE

SUC. Ø#1 ACCESSHOLE Ø1[25] SUC. Ø#2
RIGGING HOLES CONTROL CIRCUIT
[152]

LIQ. Ø#1 LIQ. Ø#2

6

Ø0.79 [20] x 4Nos. POWER SOURCE HOLE Ø0.75[19]

HOLE Ø1[25] CONTROL CIRCUIT
HOLE Ø0.75[19]

MODELS:
AUMRAUMR- 240 & 300
Models : 240 & 300 4-Ø0.79 [20] HOLES
MODELS: AUMR- 240 & 300 4-Ø0.79FOR ANCHOR BOLTS
[20] HOLES LEGEND
[254][254]

FOR ANCHOR BOLTS LEGEND

10 10

A1
A2 1 CONDENSER COIL
A1
A2 1 CONDENSER COIL
2 CONDENSER FAN
2 CONDENSER FAN
3 CONTROL PANEL
3 CONTROL PANEL
4 COMPRESSOR
4 COMPRESSOR
ALL DIMENSIONS
ALL DIMENSIONS ARE IN
ARE IN INCHES INCHES [mm]
[mm]
A1-A4
A1-A4 ARE ARE LOADING
LOADING POINTS POINTS

ACCESS
ACCESS

11

A3 A4
A4
[254]

A3
1010
[254]

43 80
[1092]43 [2032] 80
2
[1092] 3 [2032] 2
3

AIR IN
[1472] [1472]
57.96 57.96

[1227] [1227]
48.31 48.31

AIR IN
[247]
9.7

4
[247]
9.7

CONTROL CIRCUIT
[100]

[152]
3.94

RIGGING HOLES SUC.Ø #1 HOLES Ø1 [25] SUC.Ø #2

Ø0.79 [20]x 4Nos. 4
LIQ.Ø #1 LIQ.Ø #2
POWER SOURCE
1/2 [38]
HOLES Ø 1CONTROL CIRCUIT
[100]

[152]
3.94

RIGGING HOLES SUC.Ø #1 HOLES Ø1 [25] SUC.Ø #2

Ø0.79 [20]x 4Nos.
LIQ.Ø #1 LIQ.Ø #2
POWER SOURCE
HOLES Ø 1 1/2 [38]

15
 SKM Split Air Conditioners
AUMR + CADX-A Series - R-410A
Air Handling Unit Dimensional Data
MODELS: MODELS:
CADX-060A to 150A to 150A
CADX-060A
CADX Models : 060A - 180A
1.5 0.75
1.5 0.75
[38] [19]

1.97
[50]

[89]
DIMENSIONS DIMENSIONS

3.5
[38] [19]

1.97
[50]
M ODEL

[89]
3.5
M ODEL
CADX LCADX W L H W A H B A C B D C E DF EJ FG J G
ACCESS ACCESS
060A 45 48 25.2 24 38 20 17.48 17.48 1.69 11.38 13.03
[1143]
060A[1219] 45 48 25.2 24 38 20
[640] [610] [965] [508] [444] [444] 17.48 [43] 17.48
[289] 1.69
[331] 11.38 13.03
[1143] [1219] [640] [610] [965] [508] [444] [444] [43] [289] [331] A1 A3
070A 45 48
45
25.2
48
24
25.2
38
24
20 17.48 17.48 1.69
38 20
11.38
17.48
13.03
1.69
A1 A3
[1143]
070A[1219] [640] [610] [965] [508] [444] [444] 17.48 [43] [289] [331] 11.38 13.03
[1143] [1219] [640] [610] [965] [508] [444] [444] [43] [289] [331]
50 56 27.2 26 46 20 20.2 20.2 3.50 13.43 15.55
090A [1270] 50[690] 56[660] 27.2
[1168] 26[508] 46
[514] 20 20.2
[514] [89] 20.2 3.50
[395] 13.43 15.55
090A[1422]
[1270] [1422] [690] [660] [1168] [514]
[341]
[514] [89] [341]
50 56 27.2 26 46 20 20.2 [508]
20.2 3.50 13.43 15.55
[395]

B
100A [1270] 50[690] [660] [1168] [508] [514] [514] 20.2
56 27.2 26 46 20 [89] 20.2 3.50
[395] 13.43 15.55
100A[1422] [341]

B
[514] [514] [89] [341]
*105A 50 56 [1270]
27.2[1422]
26 [690]46 [660]20 [1168]
20.2 [508]
20.2 3.50 13.43 15.55
[395]
[1270]
*105A[1422] 50 56 27.2 26
[690] [660] [1168] [508] 46
[514] 20
[514] 20.2
[89] 20.2
[341] 3.50
[395] 13.43 15.55
*120A 50 56 [1270]
27.2[1422]
26 [690]46 [660]20 [1168] 20.2 [514]
20.2 [508] 3.50 [514]
13.43
[89] [341]
15.55
[395] FILTER
[1270]
*120A[1422] 50[690] 56[660] 27.2
[1168] 26[508] 46
[514] 20 [514] 20.2
[89] 20.2
[341] 3.50
[395] 13.43 15.55 REMOVAL FILTER
*150A 58 70 [1270]
30.2[1422]
29 [690]60 [660]25 [1168] 25.73 [514]
25.73 [508] 2.48 [514]
15.91 [89]
18.54 [341] [395] REMOVAL
[1474]
*150A[1778] 58[767] 70[737] 30.2
[1524] 29[635] 60
[653] 25 [653] 25.73
[63] 25.73
[404] 2.48
[653] 15.91 18.54
[1474] [1778] [767] [737] [1524] [635] [653] [653] [63] [404] [653] A2 A4
Table 10
A2
4-Ø0.5[13] A4

[165]
4-Ø0.5[13]
MOUNTING HOLES

6.5

[165]
MOUNTING HOLES

6.5
LEGEND
LEGEND
W L
W L
1 EVAPORATOR COIL
2 EVAPORATOR 1 EVAPORATOR
FAN COIL D G E
D G E 1 2 3 4
F

3 EVAPORATOR 2 EVAPORATOR
FAN MOTOR FAN
1 2 3 4
F

4 3 EVAPORATOR
1" THICK FLAT FILTER FAN MOTOR LIQ.Ø
4 1" THICK FLAT FILTER LIQ.Ø
ALL DIMENSIONS ARE IN INCHES [mm] SUC.Ø
J

S/A
SUC.Ø
A

ALL DIMENSIONS
POINTS ARE IN INCHES [mm]
H

A1-A4 ARE LOADING

J

S/A R/A

C
A
H

MODELS WITH A1-A4 ARE CIRCUITS

DOUBLE LOADING USE
POINTS
R/A

C
DRAIN SIZE 1*MODELS
[25] FOR WITH
MODELS 150 & CIRCUITS
DOUBLE 300 USE
DRAIN SIZE 1 [25] FOR MODELS 150 & 300 CABLE
ENTRY Ø
CABLE DRAIN Ø3/4[19]
[30]

[83]
1.2

3.3

2.5 ACCESS
ENTRY Ø DRAIN Ø3/4[19]
[30]

[83]
1.2

3.3

[63] 2.5 ACCESS

[63]
MO DELS: CADX-180A to 300A

CADX Models : 215A - 300A

MO DELS: CADX-180A to 300A

1.5 4-Ø0.5 [13] .7

[102]
MOUNTING HOLES
[50]

LEGEND [38] 4-Ø0.5 [13] [19] 4

2

ACCESS
1.5 .7

[102]
MOUNTING HOLES
[50]

LEGEND [38]

4
[19]
2

1 EVAPORATOR COIL ACCESS

2 EVAPORATOR FAN
1 EVAPORATOR COIL
3 EVAPORATOR FAN MOTOR FAN
2 EVAPORATOR
4 1" THICK FLAT FILTER
3 EVAPORATOR FAN MOTOR
ALL DIMENSIONS4 ARE
1" THICK FLAT[mm]
IN INCHES FILTER
A1-A4 ARE LOADING POINTS
ALL DIMENSIONS ARE IN INCHES [mm]
A1-A4 ARE LOADING POINTS
MODEL DIMENSIONS
CADX L W H A H1 B D E F J G
MODEL DIMENSIONS
B

180A 60CADX70 33.2 32 1.2 60 13.2 13.2 8.98 13.43 43.7

L W
[1524] [1778] [843] [813] H A
[30] [1524] H1 B
[334] [334] D
[228] E F
[341] [1109] J G
B

215A 61.4180A92 60 35.2 70 33.5 33.2

1.8 3282 1.2
19.86 60
19.86 6
13.2 13.2 8.98 13.43
15.91 52.28 43.7
[1560] [2337][1524]
[895] [1778]
[850] [843]
[45] [813]
[2083] [504] [1524]
[30] [504] [152]
[334] [334] [228] [341]
[404] [1328] [1109]
240A 61.4215A92 61.435.2 92 33.5 35.2
1.8 33.5
82 1.8
19.86 82
19.86 6
19.86 19.86 6
15.91 52.28 15.91 52.28
[1560] [2337][1560]
[895] [2337]
[850] [45] [850]
[895] [2083] [45] [504]
[504] [2083] [152]
[504] [404] [1328]
[504] [152] [404] [1328]
300A 61.4240A92 61.435.2 92 33.5 1.8 33.5
35.2 82 1.8
19.86 19.86
82 6
19.86 15.91 52.28
19.86 6 15.91 52.28
[1560] [2337][1560]
[895] [2337]
[850] [45] [850]
[895] [2083] [45] [504]
[504] [2083] [152]
[504] [404] [1328]
[504] [152] [404] [1328]
61.4 92 35.2 33.5 1.8 82 19.86 Table
6 11 15.91 52.28 FILTER
300A [1560] 19.86 REMOVAL
[2337] [895] [850] [45] [2083] [504] [504] [152] [404] [1328]
FILTER
REMOVAL

ACCESS
[152]
6

W 1 L
[25] ACCESS
[152]
6

D G W E 1 L
1 [25] 2 4
D G E
SUC.Ø#1 1 2 5 4
F

LIQ.Ø#1
SUC.Ø#2 SUC.Ø#1 5
F

LIQ.Ø#2 S/A
J

LIQ.Ø#1
A
H

[635]
25

SUC.Ø#2
LIQ.Ø#2 S/A
J
A
H

[635]
25

CABLE ENTRY
[83]
3.3
H1

2.5 Ø 1 [25] DRAIN Ø1[25]

[63]
CABLE ENTRY
[83]
3.3
H1

2.5 Ø 1 [25] DRAIN Ø1[25]

16 [63]
SKM Split Air Conditioners
AUMR + CADX-A Series - R-410A
Loading Points
Weights:
MODEL LOADING POINTS TOTAL MODEL LOADING POINTS TOTAL
Units Units
AUMR A1 A2 A3 A4 WEIGHT CADX A1 A2 A3 A4 WEIGHT
lbs 47 61 53 65 226
lbs 82 85 82 83 332 060A
60 kg [21] [28] [24] [29] [102]
kg [37] [39] [37] [38] [151]
lbs lbs 47 61 53 65 226
85 89 85 87 346 070A
70 kg [21] [28] [24] [29] [102]
kg [39] [40] [39] [39] [157]
lbs 84 88 84 87 343 lbs 79 83 72 71 305
90 090A
kg [38] [40] [38] [39] [155] kg [36] [37] [32] [32] [138]
lbs 105 109 105 108 427 lbs 81 84 73 73 312
100 100A
kg [48] [49] [48] [49] [194] kg [37] [38] [33] [33] [141]
lbs 141 141 142 143 567 lbs 80 84 73 72 310
105 105A
kg [64] [64] [64] [65] [257] kg [37] [38] [33] [33] [140]
lbs 159 159 161 162 [641] lbs 87 91 79 78 334
120 120A
kg [72] [72] [73] [74] [291] kg [39] [41] [36] [35] [152]
lbs 168 168 169 170 675 lbs 115 120 104 103 442
150 150A
kg [76] [76] [77] [77] [306] kg [52] [54] [47] [47] [200]
lbs 166 166 168 168 668 lbs 119 133 105 113 470
180 180A
kg [75] [75] [76] [76] [302] kg [54] [60] [48] [51] [213]
lbs 204 204 206 207 821 lbs 160 182 143 155 639
215 215A
kg [93] [93] [93] [94] [373] kg [72] [83] [65] [70] [290]
lbs 217 217 220 220 874 lbs 160 183 143 155 642
240 240A
kg [98] [98] [100] [100] [396] kg [73] [83] [65] [70] [291]
lbs 221 221 224 224 890 lbs 180 202 159 171 712
300 300A
kg [100] [100] [102] [102] [404] kg [82] [92] [72] [77] [323]
Table 12 Table 13

Recommended Suction and Liquid Line Sizes:

PIPE LENGTH - FEET (m)
Models
25 (7.6) 50 (15.2) 75 (22.9) 100 (30.5)
Circuit 1 Circuit 2 Circuit 1 Circuit 2 Circuit 1 Circuit 2 Circuit 1 Circuit 2
AUMR CADX
Liquid Suction Liquid Suction Liquid Suction Liquid Suction Liquid Suction Liquid Suction Liquid Suction Liquid Suction
060 060A 1/2 7/8 - - 1/2 1 1/8 - - 1/2 1 1/8 - - 5/8 1 1/8 - -
070 070A 1/2 7/8 - - 1/2 1 1/8 - - 5/8 1 1/8 - - 5/8 1 3/8 - -
090 090A 1/2 1 1/8 - - 5/8 1 1/8 - - 5/8 1 3/8 - - 5/8 1 3/8 - -
100 100A 5/8 1 1/8 - - 5/8 1 1/8 - - 5/8 1 3/8 - - 5/8 1 3/8 - -
105 105A 1/2 7/8 1/2 7/8 1/2 7/8 1/2 7/8 1/2 1 3/8 1/2 1 3/8 1/2 1 3/8 1/2 1 3/8
120 120A 1/2 7/8 1/2 7/8 1/2 1 1/8 1/2 1 1/8 1/2 1 1/8 1/2 1 1/8 5/8 1 1/8 5/8 1 1/8
150 150A 1/2 7/8 1/2 7/8 1/2 1 1/8 1/2 1 1/8 5/8 1 1/8 5/8 1 1/8 5/8 1 3/8 5/8 1 3/8
180 180A 1/2 1 1/8 1/2 1 1/8 5/8 1 1/8 5/8 1 1/8 5/8 1 3/8 5/8 1 3/8 5/8 1 3/8 5/8 1 3/8
215 215A 5/8 1 1/8 5/8 1 1/8 5/8 1 3/8 5/8 1 3/8 5/8 1 3/8 5/8 1 3/8 5/8 1 3/8 5/8 1 3/8
240 240A 5/8 1 1/8 5/8 1 1/8 5/8 1 3/8 5/8 1 3/8 5/8 1 3/8 5/8 1 3/8 3/4 1 3/8 3/4 1 3/8
300 300A 5/8 1 1/8 5/8 1 1/8 3/4 1 3/8 3/4 1 3/8 3/4 1 3/8 3/4 1 3/8 3/4 1 5/8 3/4 1 5/8
Table 14

Notes :
1. Pipe diameters are based on equivalent length of copper tubing sizes.
2. Pipe sizes are based on 2ºF (1.1ºC) or less temperature losses for liquid and suction line in equivalent pipe length.
3. If the condensing unit is below the evaporating unit, the maximum lift should not exceed to 66 feet.
4. Do not exceed 100 feet piping length without checking with SKM.
5. These sizes are for guidance only. For detailed proper piping, refer to recognized piping references like ASHRAE
Guide and Data Book.
The recommended or required suction and liquid line sizes do not necessarily correspond with the refrigerant
connections available on the outdoor or indoor unit. Necessary transformation may be required and it’s field performed.

17
 SKM Split Air Conditioners
AUMR + CADX-A Series - R-410A
Recommended Clearances
30 30

SPACING FOR SERVICE [762] [762]

SPACING FOR FLOW

[762]
30
ALL DIMENSIONS ARE IN INCHES [mm]

[762]
30

[1143]
45
[762]
30

30 30
[762] [762]
[762]

AUM R- 060 to 100

30

SINGLE UNIT

30 30
[762] [762]
AUM R- 060 to 100
MULTIPLE UNIT

52 52
[1321] [1321]
SPACING FOR SERVICE
[1322]

[1322]
52

52

SPACING FOR FLOW

[762]
30

ALL DIMENSIONS ARE IN INCHES [mm]

[762]
30
[1322]

[1322]
52

52

AUM R- 105 to 300

SINGLE UNIT
52 88 52
[1321] [2235] [1321]
[1322]

[1322]
52

52
[762]

[762]
30

30
[762]

[762]
30

30
[1322]

[1322]
52

52

AUM R- 105 to 300

MULTIPLE UNIT

18
SKM Split Air Conditioners
AUMR + CADX-A Series - R-410A
Installation and Commissioning
• Install the unit in such a location which is flat and strong enough to support its weight.

• All field wiring must comply with applicable local and national codes.

• Service spacing should be provided as shown in the figure. If any obstacles are around the unit, distributed air is short-circuited
so that the unit stops frequently and access to the unit is difficult for inspection and aftersales services.

SPACING FOR SERVICE SPACING FOR AIR FLOW

No obstacle

3000mm
AIR OUT

No obstacle
AIR OUT
3000mm

AIR OUT

L
RO
NT EL
CO PAN IN
A IR
L
RO
NT EL A IR
CO PAN IN

IN
AIR
A IR IN

UID ION
LIQLINE CT E
ION S U LIN AIR
CT
UID S U LINE IN
LIQLINE

L
AIR
IN
IT TROIT
CU R ON CU
RO
L CIR OWE C CIR
NT IT P IN
C OCIRCU A IR A IR
UID
IN
R LIQLINE
WE IT
POIRCU
C N
CTIO
SU LINE

AUM R- 060 & 70 AUM R- 105 to 180

No obstacle
3000mm

AIR OUT

No obstacle
AIR OUT
3000mm

L
RO
NT EL
CO PAN IN
AIR
L
CONTROEL A IR
PAN IN

IN
AIR
A IR IN

UID ION
N LIQLINE CT E
CTIO S U LIN AIR
UID S U LINE IN
LIQLINE

L
IN RO
AIR IT
CU R NT IT
L CIROWE COCIR CU
RO
NT IT P IN
C OCIR CU AIR
IN A IR
R UID
WE IT LIQLINE
POIRCU
C
ION
CT
SU LINE
AUM R- 090 & 100 AUM R- 215 to 300

19
 SKM Split Air Conditioners
AUMR + CADX-A Series - R-410A
Typical Refrigeration Piping

LEGEND
LEGEND
1-SIGHT
1-SIGHTGLASS.
GLASS.
2-SOLENOID
2-SOLENOIDVALVE.
VALVE.
3-FILTER
3-FILTERDRIER.
DRIER.
4-SHUT
4-SHUTOFF
OFFVALVE.
VALVE.
5-LIQUID
5-LIQUIDLINE.
LINE.
6-SUCTION
6-SUCTIONLINE.
LINE.
NOTE:
NOTE:
CADX EXPANSION
EXPANSIONVALVE
VALVEINSIDE
INSIDECADX
CADXA.A.
CADXA.A.
AUMR.
AUMR.

11 R/ AR/ A
66 22
55 33
44

LEGEND
LEGEND
CADX
CADXA.A. 1-SIGHT
1-SIGHTGLASS.
GLASS.
2-SOLENOID
2-SOLENOIDVALVE.
VALVE.
3-FILTER
3-FILTERDRIER.
DRIER.
4-SHUT
4-SHUTOFF
OFFVALVE.
VALVE.
R / AR / A
5-LIQUID
5-LIQUIDLINE.
LINE.
6-SUCTION
6-SUCTIONLINE.
LINE.
11
22
NOTE:
NOTE:
33 EXPANSION
EXPANSIONVALVE
VALVEINSIDE
INSIDECADX
CADXA.A.
44

**

55 66 AUMR.
AUMR.

* *INVERTED
INVERTEDTRAP
TRAPWITHOUT
WITHOUTPUMP
PUMPDOWN
DOWNCONTROL.
CONTROL.
DOTTED
DOTTEDWITH
WITHPUMP
PUMPDOWN
DOWNCONTROL.
CONTROL.

Refrigerant Piping:
Correct design and size of refrigerant piping is necessary to proper operation. The refrigerant piping generally should be
designed to accomplish the following:

a) To ensure proper refrigerant feed to the evaporator.

b) To provide practical refrigerant line sizes without excessive pressure drop.
c) To maintain uniform return of lubricating oil to the compressor.
d) To prevent refrigerant from entering the compressor and causing compressor damage due to “slugging”.

20
SKM Split Air Conditioners
AUMR + CADX-A Series - R-410A
GUIDE SPECIFICATIONS
GENERAL EVAPORATOR COIL
Spilt air conditioner shall be composed of compressor(s), Evaporator coil shall be constructed of inner grooved copper
condenser & evaporator coils with fans, refrigerant piping, tubes 3/8” OD mechanically bonded to aluminum cross wave fins.
electrical components & enclosing cabinet in one piece. These Coil consists of headers of seamless copper tubing, thermostatic
units shall be factory assembled, internally wired, fully refrigerant expansion valve(s) & multi-circuited distributor(s). These coils
charged with R410A, tested under strict quality standards & are shall be tested against leakage by 450 psig high pressure under
suitable for outdoor installation on rooftop or ground level with water, cleaned & dehydrated at the factory. Coil shall conform
ducted system. These units shall be capable to operate from to AHRI-410.
50 °F (10°C) to 125 °F (51.7°C) ambient temperature without
failure & shall be rated in accordance with AHRI-340/360 and
AHRI- 210/240 standards. Capacity as per attached schedule.
EVAPORATOR FAN & MOTOR
Fans of evaporators shall be forward curved, double inlet
CONDENSING UNIT double width (DIDW), centrifugal type, Statically & dynamically
balanced, mounted on a single heavy duty statically & shaft
The condensing unit shall be composed of compressor(s), coil(s) with permanently lubricated bearings & driven by V belt with
and condenser fan(s) and motor(s). an adjustable variable pitch motor pulley. Motor shall be Totally
Enclosed Fan Cooled (TEFC), 4 poles, class-F insulated,
minimum IP55 protection & wired to unit control panel.

COMPRESSOR(S)
Compressor shall be hermetically sealed, compact high efficiency CASING
and low noise scroll type. These compressors are refrigerant gas
cooled, furnished with advanced scroll temperature protection The unit casing for CADX-A is made of zinc coated galvanized
or internal motor protection. steel sheets conforming to JIS-G3302 and ASTM A525 which
is phosphatized and baked after an electrostatic powder coat
of approximately 60 microns. This finish and coating can pass
a 1000 hour in 5% salt spray testing at 95°F (35°C) and 95%
CONDENSER COIL(S) relative humidity as per ASTM B117. Panels and casing are
insulated with 1” (25mm) thick fiberglass (with BGT coating)
Condenser coils shall be air cooled with integral sub cooler, thermal and acoustic insulation having density of 2 lb/ft³. (32
constructed of special inner grooved seamless copper tubes kg/m³) and thermal conductivity of 0.23 BTU.in/ft²°Fh (0.033
3/8” OD mechanically expanded into waffle louver aluminum fins W/m°K). Insulation meets the requirements of NFPA 90A and
. These coils shall be tested against leakage by high pressure 90B for fire resistance.
under water, cleaned & dehydrated at the factory.

FILTER SECTION
CONDENSER FAN(S) & MOTOR(S)
Air handling units shall be provided with air filter. Filter should
The machine shall be furnished with direct driven propeller type be 1” (25mm) standard or 2” (50mm) thick optional washable
discharging air upward condenser fans. Fans shall be constructed aluminum media with average dust arrestance 54% based on
of corrosion resistant blades such as heavy gauge aluminum. The ASHRAE standards 52.1.
fan and drive shall be held in proper alignment. Fan assemblies
shall be provided with heavy gauge, rust resistant steel wire fan
guard. All condenser fans shall be individually, statically, and CONTROL PANEL
dynamically balanced for vibration free operation.Motors shall
be Totally Enclosed Air Over (TEAO), 4 pole or 6 pole, class F The panel shall be factory wired and confirm to IP-54 requirements.
insulation, minimum IP-54 protection and factory wired to unit Control panel shall contain compressor and motor starting
control panel. contactors, electronic control board for unit operation, compressor
anti-recycle time delay, control on/off switch, control circuit breaker
and power & control terminal blocks. High and Low pressure
switches should be provided for protection.

21
 SKM Split Air Conditioners
AUMR + CADX-A Series - R-410A

NOTES

22
SKM Split Air Conditioners
AUMR + CADX-A Series - R-410A

NOTES

23
 SKM Split Air Conditioners
AUMR + CADX-A Series - R-410A
HEAD OFFICE
P.O Box: 6004
Sharjah, United Arab Emirates
Tel: +971 6 514 3333
Fax: +971 6 514 3300
Email: sales@skmaircon.com
Email: info@skmaircon.com

Spare Parts Division

Email: spareparts.skm@skmaircon.com

Service Centre
Email: aftersales.skm@skmaircon.com

REGIONAL OFFICES
United Arab Emirates
Abu Dhabi Dubai
P.O Box: 27788 P.O Box: 98822
Tel: +971 2 6445223 Tel: +971 4 2940900
Fax: +971 2 6445145 Fax: +971 4 2940029
Email: abudhabisales.skm@skmaircon.com Email: dubaisales.skm@skmaircon.com
Al Ain
Tel: +971 3 7619921 Kuwait
Fax: +971 3 7619941 Dasman
Email: alainsales.skm@skmaircon.com P.O Box: 1215-PC 15463
Tel: +965 2 2492200
Saudi Arabia (Production Facility) Fax: +965 2 2494400
Email: kuwaitsales.skm@skmaircon.com
SKM Air Conditioning Factory
Eastern province
AD Dammam Algeria
2nd industrial city Aissat Idir ( EX-ENMA) City
Abqiq main road Hail Street Bldg1, Flat 2, Dar El Beida Algiers
Tel: +966 3 8123332 / 4 / 5 Tel: +213 21 508197
Fax: +966 3 8123337 / +966 3 8123092 Fax: +213 21 508197
Email: saudifactory.skm@skmaircon.com Email: algeriasales.skm@skmaircon.com

For SKM Distributors visit:

www.skmaircon.com

24 080/2016
Supersedes # 080/2015