Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 4K views

    ZXMW NR9150 Commissioning Guide 4-0

    Uploaded by

    Jambul Is
    1. The document provides instructions for logging into and configuring the LMT and NR9150 devices. It describes how to set the IP address and subnet mask on a PC to connect to the LMT and log in via the web interface. 2. Configuration steps are outlined for the NR9150, including setting up the PLA, system, time, SNMP, radio channels, XPIC, ports, VLANs, routing, QoS, and trust modes. Frequency, bandwidth, modulation and other parameters are configured for each radio. 3. Ports 5-8 on the NR9150 can be used to remotely access the IDU if the laptop and IDU IP addresses are on the

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    ZXMW NR9150 Commissioning Guide 4-0

    Uploaded by

    Jambul Is
    4K views21 pages
    1. The document provides instructions for logging into and configuring the LMT and NR9150 devices. It describes how to set the IP address and subnet mask on a PC to connect to the LMT and log in via the web interface. 2. Configuration steps are outlined for the NR9150, including setting up the PLA, system, time, SNMP, radio channels, XPIC, ports, VLANs, routing, QoS, and trust modes. Frequency, bandwidth, modulation and other parameters are configured for each radio. 3. Ports 5-8 on the NR9150 can be used to remotely access the IDU if the laptop and IDU IP addresses are on the

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    1. The document provides instructions for logging into and configuring the LMT and NR9150 devices. It describes how to set the IP address and subnet mask on a PC to connect to the LMT and log in via the web interface. 2. Configuration steps are outlined for the NR9150, including setting up the PLA, system, time, SNMP, radio channels, XPIC, ports, VLANs, routing, QoS, and trust modes. Frequency, bandwidth, modulation and other parameters are configured for each radio. 3. Ports 5-8 on the NR9150 can be used to remotely access the IDU if the laptop and IDU IP addresses are on the

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    4K views21 pages

    ZXMW NR9150 Commissioning Guide 4-0

    Uploaded by

    Jambul Is
    1. The document provides instructions for logging into and configuring the LMT and NR9150 devices. It describes how to set the IP address and subnet mask on a PC to connect to the LMT and log in via the web interface. 2. Configuration steps are outlined for the NR9150, including setting up the PLA, system, time, SNMP, radio channels, XPIC, ports, VLANs, routing, QoS, and trust modes. Frequency, bandwidth, modulation and other parameters are configured for each radio. 3. Ports 5-8 on the NR9150 can be used to remotely access the IDU if the laptop and IDU IP addresses are on the

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 21

    1.

    Login to the LMT


    1> Set the IP address of the PC to “192.168.1.X” (X is in the range of 2–254), and set
    the subnet mask to “255.255.0.0”.

    2> Connect the PC to the LMT port.

    3> In the security mode is enabled by default, and login should be made through the
    https mode. Launch a Web browser, enter https://192.168.1.1 in the address bar,
    and press the Enter key. The security certification prompt is displayed, as shown in
    the figure below. Select “Continue to this website (not recommended). Figure 2-1
    Security Certificate Prompt Page

    4> The LMT login view appears, as shown in the figure below
    5> In the User Name area, enter ztemw. In the Password area, enter User1234, and
    then click LOGIN to enter the home page of the LMT, as shown in the figure below.

    When click “slot1” IF port, the home page will show the radio-1/1/0/1 and radio-
    1/1/0/2 information
    When click “slot4” IF port, the home page will show the radio-1/4/0/1 and radio-
    1/4/0/2 information
    2. Configure the NR9150
    1> Configure “PLA”

    Select “Basic Config>>PLA”

    Click “Add” button


    Set “Mode” as “basic” Set “PLA ID” as “pla-1/1/0/1”

    Select all port “tu-1/1/0/1,tu-1/1/0/2,tu-1/4/0/1,tu-1/4/0/2”

    then click “Apply” button, as follow”:

    2> Configure “System”


    Select “Basic Config>>System”
    Site ID: Type in the site id according to planning data

    NE Name: Type in the site id according to planning data

    NE DCN: select “Disable

    IP Type: select”IPv4”

    NE IP: Type in the site id according to planning data

    Then click “Apply” button


    3> Configure “Time”

    Select “Basic Config>>Time”

    Time Zone Mode: select “System Time Zone”

    System Time Zone Name: select “(UTC+07:00) Asia/Jakarta”

    NTP Switch: select “ON”

    Source IPv4 Address: Type in the NE’s IP


    Server Info: add 172.29.250.20 priority 5
    add 172.29.250.83 priority 4
    4> configure “SNMP”
    Select “ Basic Config>>SNMP”

    Switch : select “Enable”

    Trap Source IPv4: Type in NE’s IP

    Add SNMPV3 user: User Name is “zte” Authentication Password is “Ztesnmp2014”

    Encryption Password is “Ztesnmp2014”

    Add SNMPV3 host: Management IP is 172.29.250.99 and 172.29.250.36, User Name is


    “zte”
    5 configure “Basic Config>>Radio Channel”

    Select “Traffic Unit Name” : radio-1/1/0/1, radio-1/1/0/2, radio-1/4/0/1, radio-1/4/0/2


    Then type in “Tx Frequency(KHz)”,” Rx Frequency(KHz)”,” TX Power(dBm)”,” Channel
    Name”” “Bandwidth(MHz)” ACM select”Enable”,” Modulation”

    NOTE:frequency is 6G and 11G , Bandwidth is 40M, Modulation is 64QAM, other frequency


    Bandwidth is 28M, Modulation is 256QAM
    XPIC configuration

    XPIC-ID: Type in 1 and 2

    XPIC: Enable

    tu-1/1/0/2 and tu-1/1/0/1 must in one group


    tu-1/4/0/2 and tu-1/4/0/1 must in one group

    Recovery Mode select “Auto”


    6 configure port

    Select “Ethernet>>Port”

    Enable port and add port description


    Configure VLAN

    Select “Ethernet>>VLAN”

    Add the planning vlan on revelant port


    VLAN interface configuration

    VLAN Interface: type in DCN vlan

    Interface IP(IPv4): type in NE’s IP

    Mask: type in NE’s mask

    Then click “Apply” button


    Routing configuration

    Select “Ethernet>>Routing”

    Destination IP: type in 0.0.0.0

    Mask: type in 0.0.0.0

    Gateway: type in NE’s gateway


    QOS configuration

    Select “Ethernet>>QoS”
    Global configurtion

    Add “DS1”,then apply


    DS configuration

    Select “DSCP”

    Set 46 as “CS6”, Set 48 as “CS7”


    Port configuration

    Add port

    DS select “DS1”
    Trust select “DSCP

    Then click “Apply”

    If you want login the remote IDU, must connect your laptop to port 5 ,6,7,8

    And set your laptop IP and ID IP in the same segment, then type in NE’s IP in the browser.

    You might also like