Tecnodue PT250 User Manual

I.T.S.
by Tecnodue
PT 250
Edition 1208
Operating Manual
I.T.S. Ital Trade Services PT 250 Operating Manual
The technical data and information contained on this manual can be changed without any notice
2
PT 250
The machine has been designed and constructed for the welding of PE, PP, PVDF and other thermoplastics pipes and fittings.
I.T.S. Ital Trade Services S.r.l.

Via Scarsellini 77 , 16149 Genova Italy
Phone : +39-010-6423396
Fax : +39-010-6423513
E Mail : info@its-tecndoue.com
Web Site : www.its-tecnodue.com
Standard Components
1. Hydraulic Unit
2. Facing Tool
3. Basic machine
4. Heating Mirror
5. Support for facing tool and heating mirror
On request can be supplied:
6. Light weight alloy reducing rings for pipes and fittings d. 63,50,75,90,110,125,140,160,180,200,225mm
7. Stub End Device
8. MDD (PT automatic mirror device)
• Short spigot fittings clamp d. 250mm
• Wooden transport box according to ISPM 15
• LDU (printing and storing data machine)
• Electric board with automatic circuit breaker
• Rollers
3
SAFETY RULES ACCORDING TO DIRECTIVES CEE

( To be read carefully and apply while utilizing the PT 250 )
Due to the specific use, this machine cannot be supplied with all kind of fix and removable protections suitable to avoid any risk of accident.
The machine, therefore, must be utilized, adjusted and keep in the perfect functioning conditions by skill operators.
Warning - Rules – Obligations
The use of machines composed by electrical components and movable parts, it's always a potential danger. In order to avoid any kind of accident caused by
electrical or mechanical sources it' strongly suggested to read and follow carefully the following safety rules before operating the machine.
TRANSPORT
-.Basic Machine , Keep the maximum care while moving and it's suggested to utilize mechanical aids.
-.Facing Tool ,supplied with transport's hook.
Keep the maximum care while moving it and it's compulsory to utilize the handle also take care about the blades mounted in, it's compulsory use gloves.
-.Heating Mirror ,supplied with transport's handles
Keep the maximum care while moving it also keep the maximum care while utilizing it due to the high temperature involved always more than 200°C ,
it's strongly suggested to use suitable gloves.
In order to move from one working place to the other , the facing tool and the mirror must located into the special support , this support is heavy therefore
it's necessary to utilize the maximum care to move it
-.Hydraulic unit, supplied with transport's frame.
Keep the maximum care while moving it and in case utilize two person.
Avoid to transport the components by holding from the cable and remember to use suitable gloves.
ELECTRIC CONNECTIONS
The machine is operated by 230 Volts therefore be sure that the power supply plug is supplied with the safety devices according to the standard
requirements , also check that the power supply will be on the range of maximum 10% of the machine's nominal tension.
While the facing tool is connected to the power supply do not leave it into the basic machine but place it into the special support. In this position, even if the
start bottom is pushed the engine does not start.
Check regularly the cables and the plug and in case substitute by qualify personnel.
In case the heating mirror cable must be substitute the cable must be H07RN-F
Before carry out a reparation or maintenance all the plugs must with plug out from the power supply
ENVIRONMENTAL CONDITIONS
The working area must be clean and duly lighted. It's very dangerous to utilize the machine in case of rain or in wheat conditions or close to flammable agents.
CLOTHES
Keep the maximum care while utilizing the machine due to the high temperature involved on the heating mirror always more than 200°C , it's strongly
suggested to use suitable gloves. Avoid long clothes and avoid bracelets , necklaces that might be hooked into the machine.
CORRECT MACHINE'S OPERATION
Remember to check and read carefully the operating manual before utilizing the machine and the accessories.
KEEP ALWAYS THE MAXIMUN ATTENTION
After the heating mirror has been disconnected temperature will be hot for some minutes.
Keep the maximum care while utilizing the facing tool. Be careful to the blades , it's strongly suggested to use suitable gloves. During the facing operation
( facing tool in movement ) it's forbidden to take out the shavings
Avoid utilizing the machine after drinking or drugs use
Take care that all the people around the machine are at safety distance
While starting operating take care to avoid leave arms between the movable and fix trolleys.
SQUASHING DANGER
While starting operating take care to avoid leave legs or arms between the movable and fix trolleys. It's compulsory to be far from the basic machine
ACOUSTIC POLLUTION
The acoustic pollution of the drill engine is less than 85 dB ( value measured at 1 meter distance from the operator)
Due to some particular cases such as too much pressure during the facing the noise should be increased , therefore it's suggested to utilize some
protections.
IMPORTANT !!!!
Keep the maximum care reading and following the above Warning - Rules - Obligations the Ital Trade Services S.r.l. decline all responsibilities if are not
followed totally
Label on machine’s components

showing potential dangers
WEAR BURNS ELECTRIC SQUASHING

GLOVES DANGER DANGER DANGER
4
1. Technical data
Operating data
Ambient temperature 0…50°C
Humidity (without condensation) 95 RH%
Transport and storing Temperature -10…60°C
Electrical data
Voltage 230 V
Frequency 50 Hz
Total power installed 3.92 KW 17 A
Heating mirror IP 54 2.3 KW
Facing tool IP 20 1.02 KW
Hydraulic unit IP 44 0.6 KW
Hydraulic data
Maximum working pressure 100 bar
Cylinder’s section 5,89 cm2
Pressure gauge 0 - 100 bar
Pressure gauge precision class Cl. 1.0
Hydraulic unit engine revolutions 1400 rpm
Volumetric pump’s capacity 1,2 cc/rev.
Pump’s capacity 1.68 l/min
Hydraulic oil ISO 46
Oil tank’s capacity 1.5 liter
Mechanical Data
Facing tool transmission system Gear drive
Trolley maximum stroke 145 mm
Trolley slide bar diameter 35 mm
Distance between the cylinders centre 360 mm
Dimensions
Basic machine 900 x 510 x 520 mm
Facing tool 650 x 480 x 85 mm
Heating mirror 465 x 550 x 65 mm
Hydraulic unit 445 x 320 x 270 mm
Support for facing tool and heating mirror 415 x 510 x 370 mm
Weights
Basic machine 45 Kg
Facing tool 14,5 Kg
Heating mirror 10 Kg
Hydraulic unit 26 Kg
Support for facing tool and heating mirror 12 Kg
Wooden transport box 55 Kg
Stub end device 6.5 Kg
Reducing inserts complete set 63.5 Kg
5
2. General description and application field

Hydraulic operated butt welding machines suitable for PE,PP,PVDF and other thermoplastics pipes and fittings.
The self aligning frame and the compact dimensions make the machines highly suited for working in road constructions, ditches , aqueducts,
gas ducts , sewers and irrigation systems.
The machine is supplied complete of:
1) Basic machine d. 250 mm complete with a tools blue bag
2) Removable electric facing tool with safety switch
3) Removable PTFE coated heating mirror with a temperature control box.
4) Electro-hydraulic motor with accumulator and flexible hoses with quick couplings.
5) Support for facing tool and heating mirror
2.1 Basic machine
The basic machine is composed by:

• Two cylinders on which heads are mounted two complete
clamps d. 250 mm
• One movable clamp d.250 mm sliding on cylinder's stem and
fixable in different positions by means of using the clamps
connecting rods.
• A stiffening bar
• One side support clamp d.250 mm
• A frame including the hydraulic circuit with the anti-drop
quick couplings.
• A heating mirror disconnecting device
2.2 Facing Tool

The electric facing tool is composed by:
• The facing tool body
• Two disks where are mounted the blades
• A drill engine with a safety pin that , while connected keep the facing tool
hooked to the machine.
• An handle with safety micro-switch allowing the engine starts only
when the facing tool is fit into the machine, avoiding the start of the
engine out of this position.
2.3 Heating Mirror

The heating mirror is composed by:
• The heating mirror coated with green color PTFE complete with
thermometer (the thermometer does not depend upon the power supply
and always survey the real temperature of the heating plate) and
connecting box
• The support suitable for the heating mirror and the facing tool
where is located the connecting box
• The electronic thermostat located on the connecting box .
• LDU connector. (The below figure shows where the LDU connector is
located ).
LDU Connector
6
2.3.1 Electronic thermostat – different functions
At each startup on the display will blink the writing ‘TEST’. This means that the
thermostat is testing the connection between the probe and the heating mirror.
If the test fails, the display will show 4 blinking upper scores (as per figure aside),
in this case the probe or the connection between the thermostat and the heating
mirror could be interrupted.
If the test success, the display will show the real temperature of the heating mirror and the
heating mirror warms up (the OUT1 red led is switched on) until the set point value (the selected
temperature) has been achieved (central green light led).
To display the actual set point value of the temperature stored by the thermostat, push the key P. The display will show alternately the
writing ‘SP1’ and the set point value of the temperature. After 5 seconds the display will show again the real value of the heating
mirror temperature
To select a new value for the thermostat set point value (default value = 220°C):
1. Push the key P (The display will show alternately the writing ‘SP1’ and the set point value of the temperature)
2. By acting on the arrow keys UP and DOWN it is possibile to increase or decrease the set point value.
3. When you reach the desired value push the key P to confirm.
4. The display will show again the real value of the heating mirror temperature
5. When the heating mirror will reach the set point value on the display the central green light led will be switched on.
Warning: On the thermostat display is always shown the actual value of the heating mirror temperature (and never the set
point value!)
Temperature of the welding mirror for welding PE DVS 2207-1 norm
225
220
Mirror temperature (°C)
215 PE 100
210
205
PE80
200
0
195
0 10 20 30 40 50 60 70
pipe wall thickness (mm)
Remember
When welding PVDF, the temperature of the welding mirror should be adjusted for every wall thickness at 240°C +/- 8°C
When welding PP, the temperature of the welding mirror should be adjusted for every wall thickness at 210°C +/-10°C
7
2.4 Hydraulic Unit
The basic components of the hydraulic unit are the following:

• Electric engine
• Hydraulic pump
• Oil tank
• Hydraulic unit controls
• Pressure accumulator
• Pressure gauge
• Metal frame
2. 4.1 Hydraulic Unit Controls
The control lever A open and close the machine's trolley according to the
position selected.
Bring the lever A into position A2 (position with automatic return) the trolley
is opening with the maximum pressure set up into the hydraulic unit
In position A1 the lever shut down automatically the engine ( release position ).
Bring the lever A into the position A3 ( position with hooking) the trolley is
closing, the hooking of such position allow the operator handling.
The hand wheel F of the pressure control allow the setting up of the
pressure at the requested values by turning anti clockwise the
pressure release , while turning clockwise the pressure increase .
The pressure by pass lever E allow ,by turning anti clockwise the
pressure releasing , while turning clockwise allow the pressure
increasing by means of using the hand wheel F and fixing. If you
completely clockwise turn the by pass valve, the pressure will be
blocked and the hydraulic unit will maintain the same pressure in case
of engine switched off.
8
2.4.2 How to use the hydraulic unit
Operating Instructions
In order to make easy the learning we shall proceed to the description step
by step of all operations need in order to complete a welding according to
the following description:
Important !
Before begin the following operation be sure that:
- The lever A is fixed into the special housing
- Substitute the metal plug with the plastic black and red plug the
plastic plug is supplied with the machine into a plastic bag.
01. Fit the two pipes to be weld ( see relative instructions )
02. By turning the lever E anticlockwise bring the pressure to zero,
checking the pressure gauge D
03. Turn clockwise the lever E until closing ( please avoid using an
excessive strength )
04. Bring the lever A into position A3
05. By turning clockwise the hand wheel F achieve the inertial pressure
value ( value of pressure need in order to allow the trolley moving )
note the value of inertial pressure read into the pressure gauge D,
then by still operating the hand wheel F , increase the inertial pressure
value by the welding theoretical pressure value as per attached table.
06. Achieved the true welding pressure value ( inertial pressure plus
theoretical welding pressure ) bring the lever A into position A2.
07. Fit the facing tool (see relative instructions )
08. By acting on lever E anticlockwise achieve a pressure value of approx 5 bar more than the inertial pressure value checked and
then proceed to the facing tool operation (taking care that the engine's overloading).
09. At the end of the facing operation bring the lever A into position A3 and remove the facing tool.
10. Fit the heating mirror taking care that the temperature of the surfaces is the one selected (see relative instructions)
11. Bring the lever A into A3 in order to have the bead formation as per attached table, this operation must be done with the true
welding pressure value.
12. After bead formation act on lever E anticlockwise in order to bring the pressure to zero and proceed to the heating time as per
attached table.
13. Elapsed the heating time at pressure zero bring the lever A into position A2 and remove the heating mirror and immediately
bring the lever A into position A3 and acting on lever E clockwise put in contact the two pipes until achieving the true welding
pressure value by checking the pressure gauge D. These operations must be done according to the time indicated into the
attached table.
14. Bring the lever A into position A1 and keep such situation for all the cooling time indicated into the attached table, taking care
that the pressure will not decrease too much, in case bring for a little while the lever A into position A3 and put back into position A1
15. Elapsed the cooling time by acting on lever E anticlockwise bring the pressure to zero.
16. Take away the pipes welded
WE STRONGLY SUGGEST TO TRY MANY TIMES AND GET FAMILIAR TO THE UNIT BEFORE CARRYING ON WITH COMPLETE WELDING.
A WRONG USE OF THE HYDRAULIC UNIT COULD COMPROMISE YOUR WELDINGS..
9
3. Heating mirror disconnecting device

You can configure the machine according to the kind of welding to be executed as per the following different ways:
• Two fixed clamps and two moveable clamps Fig. 1
• One fixed clamp and three moveable clamps Fig. 2
You can change from a configuration to another in a quick way by simply acting on the two spacers and on the disconnecting device.
In the first configuration of the machine the disconnecting devices is between the two moveable clamps and the two fixed clamps.
The spacers are between the two fixed clamps.
In the second configuration of the machine the disconnecting devices is between the three moveable clamps and the fixed clamp.
The spacers are between the second and third moveable clamps.
Figure 1.Configuration 2 moveable clamps + 2 fixed clamps Figure 2.Configuratione 3 moveable clamps + 1 fixed clamp
Figure 3.
On the left: The special shape of the spacers let a quick configuration of the machine.
You can easily chage the spacer position without using any kind of tool.
You can modify the distance between the clamps connected by the spacers.
Fix the first clamp to the hole D and the second clamp in one of the holes A,B,C
On the right (from above) Upper and lower spacer (interchangeable) and
disconnecting device
WARNING !
Only in two confirgurations you can use the disconnecting device with spacer! In the other configuration use only the spacer to
avoid serious damages to the basic machine!
10
How to change the configuration from two fixed clamps and two sliding clamps into one fixed clamp and three sliding clamps
WARNING!
You can only place the upper and lower spacers in the same clamps and using the same holes. It is strictly forbidden to put the
spacer in different clamps and in different holes.
1. Configuration 2 moveable clamps + 2 fixed clamps

2. Not completely close the trolleys
3. Remove the heating mirror disconnecting device
4. Lift the spacers as shown in the figure above
5. By using your hands translate the third clamps as in the figure above
6. Remove the spacers
7. Place the spacers between the two central clamps
8. By using your hands translate the moveable clamps until the clamp reaches the limit stop.
9. Fix the spacers by pushing them down
10. Place the heating mirror disconnecting device
11. To fix the heating mirror disconnecting device open the trolleys
12. Configuration 3 moveable clamps + 1 fixed clamp
To configure the again the machine with 2 moveable clamps you must repeat the procedure above in a reverse sense.
11
3.1 Beep-beep inserts reductions
To use a beep-beep insert reduction
To use a beep-beep reduction, fix it by lightly pushing

the reduction in the direction shown as per figure
aside. As you hear a ‘click’ sound the reduction is
properly fixed.
To remove the beep-beep reduction
To safely remove the beep-beep reduction by means

of a screwdriver turn to left the screw shown in the
figure aside. As soon as the reduction is not anymore
hooked to the clamp you can remove it.
12
4. Butt welding in brief

4.1 Introduction
Stated that the basic machine it's suitable for all kinds of pipe, fittings and stub end available on the nowadays market. Here follows all the
different welding configurations of the machine:
1) Pipe with Pipe, standard configuration of the machine
2) Pipe with long spigot fitting, standard configuration of the machine
3) Pipe with short spigot fitting, to achieve this kind of welding it is strongly suggested to configure the machine with three moveable
clamps and 1 fixed clamp. Furthermore you must use the upper fittings clamp to fix better the fittings to the fixed clamp
4) Fitting with short spigot stub end, to achieve this kind of welding it is strongly suggested to configure the machine with three
moveable clamps and 1 fixed clamp. To fix the stub end you must use a special accessory called stub end device. Place the 4
brackets at the appropriate size punched on the stub end device. Fix the stub end by tighten the bolt of each bracket. The stub
end device is supplied with a fixing ring and you can install it on each clamp of the machine.
5) Pipe with short spigot stub end, to achieve this kind of welding you can use two different configuration of the machine (5 or 6)
6) Pipe with short spigot stub end, to achieve this kind of welding you can use two different configuration of the machine (5 or 6)
1. PIPE WITH PIPE 2. PIPE WITH LONG SPIGOT FITTING 3. PIPE WITH SHORT SPIGOT FITTING
4. FITTING WITH SHORT SPIGOT STUB END 5. PIPE WITH SHORT SPIGOT STUB END 6. PIPE WITH SHORT SPIGOT STUB END
4.2 Machine's preparation

It's strongly suggested to use pipe rollers for the sliding of the pipes to be welded and if it's possible positioning the machine
with wooden table below, such cares will avoid additional efforts to the machine.
a) Set up the working area so that welding is protected from the weather. Position the machine's components as per following figure
and eventually utilize wooden panels
b) Connect the flexible hoses of the hydraulic unit to the machine

13
c) Connect the plugs to the power supply (Hydraulic unit, Facing tool and Heating mirror) after checking that the main power
supply is within a 10% of the specified one “ Warning Heating Mirror start to warm up ! “
d) Select the correct temperature on the heating mirror
e) In case fit the inserts of the diameter to be welded into the machine
4.3 Pipes positioning into the machine and facing operation

a) Open the movable trolley of the machine by means of acting the lever A (hyd. Unit) and take
it in position A2
b) Position the pipes into the machine taking care to leave enough space for the facing tool inserting
c) Check the pipes alignment, in case adjust it by means of tighten or loosing the clamps bolts.
The maximum misalignment could be lesser than 10% of the pipe or fittings wall thickness.
In any case the misalignment cannot be over than 2mm.
d) Clean the pipe ends
e) Fit in the facing tool between the two pipe's ends to be faced, by means of connecting the facing
tool into the special supports. Connect the safety pin and start the facing tool engine
f) On the facing tool there is a facer stopper (see the figure aside). In case of one of the pipe ends
has a small projection; the facer stopper let you select the only pipe to face. Put the facer stopper in
the left or in the right hole to prevent the right or left facing. To face all the pipes put the facer stopper
in the central hole.
Warning!!!: Always check that the speed selector of the drill engine is in position 1 (lower
speed)
g) Slowly approach the pipes ends towards the facing tool by means of acting on the hydraulic control unit (lever A Table V ) keeping
a value of pressure allowing the facing of the surfaces and avoiding an overload of the drill engine (a too much high pressure could
burnt out the drill engine). When shavings from both sides will appear continuous and homogeneous , the facing operation is
completed.
h) Put in contact the two pipes ends to be welded and check if the eventual disjunction is within the values of the following table:
Outside diameter Port

mm mm
< 400 0,5
> 400 1,0
In case the above values cannot be fulfilled the facing operation must be repeat.
4.4 Inertial pressure measurement

Before begin a welding cycle it is necessary to measure the inertial pressure. This value must be added to the pressure value shown in our
welding tables. The inertial pressure value depends on welding operating conditions (ex.: length and weight of the pipe to drag, general
condition of the machine, ambient temperature, etc.). To measure the inertial pressure follow these steps:
a) Completely open the movable trolley of the machine by means of acting the lever A and take it in position A2
b) By turning the lever F (Hyd. Unit) anticlockwise bring the pressure to zero, checking the pressure gauge
c) Turn clockwise the lever E (Hyd. Unit) until closing
d) Bring the lever A (Hyd. Unit) into position A3 (the trolleys do not move because there is no pressure)
e) By turning clockwise the hand wheel F note the inertial pressure value ( value of pressure need in order to allow the trolley moving ) by
reading it into the pressure gauge
14
4.5 Welding cycle
To obtain the best result we strongly suggest allowing the use of the machine only to experienced operators
The welding phase is composed by 5 phases with 5 different times:

PHASE 1 = t1 = Time requested for the bead formation with the specified wall thickness
PHASE 2 = t2 = Time requested for the continual heating
PHASE 3 = t3 = Time requested for the change over
PHASE 4 = t4 = Time requested for bringing up the pressure
PHASE 5 = t5 = time requested for cooling down
Pressure-Time diagram for butt welding
PHASE 1 = Heating up t1
a) Fit the heating mirror taking care that the temperature of the surfaces is the one selected
b) Bring the lever A (Hyd. Unit) into position A3 in order to have the bead formation as per attached table, this operation must be done
with the true welding pressure value: ( Inertial pressure + P1 ).
c) Check the Bead formation wall thickness according to the attached welding table
PHASE 2 = Heating up t2
a) After bead formation act on lever E (Hyd. Unit) anticlockwise in order to bring the pressure nearly to zero and proceed to the heating
time t2 at pressure P2
PHASE 3 = Change over t3
a) Elapsed the heating time at pressure P2 bring the lever A (Hyd. unit) into position A2 and remove the heating mirror and immediately
bring the lever A into position A3 and acting on lever E clockwise put in contact the two pipes
PHASE 4 = Bringing up pressure t4
a) Achieve the true welding pressure value: (Inertial pressure + P1 = P5 ) by checking the pressure gauge, This operation must be done
according to the time indicated into the attached welding table.
PHASE 5 = Cooling Down t5
a) Bring the lever A into position A1 and keep such situation for all the cooling time indicated into the attached welding table, taking care
that the pressure will not decrease too much
b) Elapsed the cooling time by acting on lever E anticlockwise bring the pressure to zero.
c) Take away the pipes welded
Important !!!
In case of any doubt please refer to the specific instructions
15
5. Welding Parameters for PE pipes & fittings DVS norm version 2207-1
Pressure-Time diagram for butt welding
t1 = Time requested for the bead formation with the specified wall thickness
t2 = Time requested for the continual heating
t3 = Time requested for the change over
t4 = Time requested for bringing up the pressure
t5 = time requested for cooling down
P1 = Pressure during the bead formation and the cooling down, this value is the result of the formula:
Pipe section( cm2 ) x Material thrust coefficient( Kg./cm2 )
____________________________________________________________ = bar
Total machine cylinders section( cm2 )
Material thrust coefficient for PE s 63 1,5 Kg./cm2

Material thrust coefficient for PP 1,0 Kg./cm2
Total PT 250 cylinders section 5,89 cm2
P2 = Pressure during the continual heating, this value either for HDPE and PP is 0,1 Kg./cm2.
Optical checking of butt welding result
16
5.1 Welding Parameters for PE & PP sheets,pipes & fittings according to DVS 2207-1 – 2207-11
Nominal Wall thickness Alignment Heating-up Changeover time Joining pressure Cooling time under
joining pressure p=0.15
Bead height on heater Heating-up time= 10 x N/mm2 0.01
plate at the end of the wallthickness (heating-
alignment time (alignment up 0.02 N/mm2)
under 0.15 N/mm2)
mm mm (minimum values) s S (maximum time) s Min (minimum values)

MATERIAL PE
Until 4.5 0.5 45 5 5 6
4.5 … 7 1.0 45 … 70 5…6 5…6 6 … 10
7 … 12 1.5 70 … 120 6…8 6…8 10 … 16
12 … 19 2.0 120 … 190 8 … 10 8 … 11 16 … 24
19 … 26 2.5 190 … 260 10 … 12 11 … 14 24 … 32
26 … 37 3.0 260 … 370 12 ... 16 14 … 19 32 … 45
37 … 50 3.5 370 … 500 16 … 20 19 … 25 45 … 60
50 ... 70 4.0 500 … 700 20 … 25 25 … 35 60 … 80
MATERIAL PP
Until 4.5 0.5 135 5 6 6
4.5 … 7 0.5 135 … 175 5…6 6…7 6 … 12
7 … 12 1.0 175 … 245 6…7 6 … 11 12 … 20
12 … 19 1.0 245 … 330 7…9 11 … 17 20 … 30
19 … 26 1.5 330 … 400 9 … 11 17 … 22 30 … 40
26 … 37 2.0 400 … 485 11 ... 14 22 … 32 40 … 55
37 … 50 2.5 485 … 560 14 … 17 32 … 43 55 … 70
Example on how to calculate the cooling down (t5) time following the DVS NORM
As per drawing above the time T corresponds to wall thickness value X in

mm. To calculate this time (t5 in minutes) please follow the formula below:
10 − 6
T = 6+ ⋅ ( x − 4,5)
7 − 4,5
Example:
If you want to calculate the cooling down time for a 6mm wall thickness pipe, you must simply substitute the variable X with the value 6:
10 − 6
T =6+ ⋅ (6 − 4,5) = 8,4 min
7 − 4,5
To calculate the other times (t3 and t4) you must use the same principle of linear interpolation.
To obtain the t2 (in seconds) value use the formula below where the variable wt corresponds to the nominal wall thickness
T2 (sec) = 10 ⋅ wt( mm )
17
6. Welding Table for PE pipes DVS norm version 2207-1

The following tables show the values to be applied during the welding cycle as per previous instructions and graph.
However in order to clarify once again the meaning of these values please kindly note:
t1 = Time requested for the bead formation to be done with pressure value = P1 + inertial pressure
t2 = Time requested for the continual heating to be done with pressure value = P2 + inertial pressure
t3 = Time requested for the change over
t4 = Time requested for bringing up the pressure at the value of pressure = P1 + inertial pressure
t5 = time requested for cooling down to be done with pressure value = P1 + inertial pressure
Important: Remember always to add the value checked of inertial pressure to the P1 and P2 values !!!!!!!
2
PT 250 - DVS 2207-1 Cyl. section cm 5,88 Welding range 90-250 mm
material PE80-100 SDR 41
D S T P1 bead P2 t2 t3 t4 P5 t5
DIAMETER WALL THICK. TEMP. BEAD FORMATION HEATING UP CHANGEOV. RAMP COOLING
mm mm °C bar mm bar sec sec sec bar min

90 2,2 220 1,5 0,5 0.. 0,1 22 0.. 5 5 1,5 6
110 2,7 220 2,3 0,5 0.. 0,2 27 0.. 5 5 2,3 6
125 3,0 220 3, 0,5 0.. 0,2 30 0.. 5 5 3, 6
140 3,4 220 3,7 0,5 0.. 0,2 34 0.. 5 5 3,7 6
160 3,9 220 4,9 0,5 0.. 0,3 39 0.. 5 5 4,9 6
180 4,4 220 6,2 0,5 0.. 0,4 44 0.. 5 5 6,2 6
200 4,9 219 7,6 1,0 0.. 0,5 49 0.. 5 5 7,6 7
225 5,5 218 9,6 1,0 0.. 0,6 55 0.. 5 5 9,6 8
250 6,1 217 11,9 1,0 0.. 0,8 61 0.. 6 6 11,9 9
PT 250 - DVS 2207-1 Cyl. section cm2 5,88 Welding range 90-250 mm

90 2,7 220 1,9 0,5 0.. 0,1 27 0.. 5 5 1,9 6
110 3,3 220 2,8 0,5 0.. 0,2 33 0.. 5 5 2,8 6
125 3,8 220 3,7 0,5 0.. 0,2 38 0.. 5 5 3,7 6
140 4,2 220 4,6 0,5 0.. 0,3 42 0.. 5 5 4,6 6
160 4,8 219 6, 1,0 0.. 0,4 48 0.. 5 5 6, 7
180 5,5 218 7,6 1,0 0.. 0,5 55 0.. 5 5 7,6 8
200 6,1 218 9,4 1,0 0.. 0,6 61 0.. 6 6 9,4 8
225 6,8 216 11,9 1,0 0.. 0,8 68 0.. 6 6 11,9 10
250 7,6 215 14,7 1,5 0.. 1,0 76 0.. 6 6 14,7 11
material PE80-100 SDR 27,6

63 2,3 220 1,1 0,5 0.. 0,1 23 0.. 5 5 1,1 6
75 2,7 220 1,6 0,5 0.. 0,1 27 0.. 5 5 1,6 6
90 3,3 220 2,3 0,5 0.. 0,2 33 0.. 5 5 2,3 6
110 4,0 220 3,4 0,5 0.. 0,2 40 0.. 5 5 3,4 6
125 4,5 220 4,4 1,0 0.. 0,3 45 0.. 5 5 4,4 6
140 5,1 219 5,5 1,0 0.. 0,4 51 0.. 5 5 5,5 7
160 5,8 218 7,2 1,0 0.. 0,5 58 0.. 6 6 7,2 8
180 6,5 217 9,1 1,0 0.. 0,6 65 0.. 6 6 9,1 9
200 7,2 216 11,2 1,5 0.. 0,7 72 0.. 6 6 11,2 10
225 8,2 215 14,2 1,5 0.. 0,9 82 0.. 6 6 14,2 11
250 9,1 214 17,5 1,5 0.. 1,2 91 0.. 7 7 17,5 12
Warning!: in case of PE100 welding, temperature T must be increased to 220°c
18


63 2,4 220 1,2 0,5 0.. 0,1 24 0.. 5 5 1,2 6
75 2,9 220 1,7 0,5 0.. 0,1 29 0.. 5 5 1,7 6
90 3,5 220 2,4 0,5 0.. 0,2 35 0.. 5 5 2,4 6
110 4,2 220 3,6 0,5 0.. 0,2 42 0.. 5 5 3,6 6
125 4,8 220 4,6 1,0 0.. 0,3 48 0.. 5 5 4,6 6
140 5,4 219 5,8 1,0 0.. 0,4 54 0.. 5 5 5,8 7
160 6,2 217 7,6 1,0 0.. 0,5 62 0.. 6 6 7,6 9
180 6,9 216 9,6 1,0 0.. 0,6 69 0.. 6 6 9,6 10
200 7,7 215 11,8 1,5 0.. 0,8 77 0.. 6 6 11,8 11
225 8,7 214 15, 1,5 0.. 1,0 87 0.. 7 7 15, 12
250 9,6 213 18,5 1,5 0.. 1,2 96 0.. 7 7 18,5 13


63 2,9 220 1,4 0,5 0.. 0,1 29 0.. 5 5 1,4 6
75 3,4 220 2, 0,5 0.. 0,1 34 0.. 5 5 2, 6
90 4,1 220 2,8 0,5 0.. 0,2 41 0.. 5 5 2,8 6
110 5,0 219 4,2 1,0 0.. 0,3 50 0.. 5 5 4,2 7
125 5,7 218 5,4 1,0 0.. 0,4 57 0.. 5 5 5,4 8
140 6,4 217 6,8 1,0 0.. 0,5 64 0.. 6 6 6,8 9
160 7,3 216 8,9 1,5 0.. 0,6 73 0.. 6 6 8,9 10
180 8,2 215 11,3 1,5 0.. 0,8 82 0.. 6 6 11,3 11
200 9,1 214 13,9 1,5 0.. 0,9 91 0.. 7 7 13,9 13
225 10,2 213 17,6 1,5 0.. 1,2 102 0.. 7 7 17,6 14
250 11,4 212 21,7 1,5 0.. 1,4 114 0.. 8 8 21,7 15


63 3,0 220 1,4 0,5 0.. 0,1 30 0.. 5 5 1,4 6
75 3,6 220 2, 0,5 0.. 0,1 36 0.. 5 5 2, 6
90 4,3 220 2,9 0,5 0.. 0,2 43 0.. 5 5 2,9 6
110 5,2 219 4,4 1,0 0.. 0,3 52 0.. 5 5 4,4 7
125 6,0 218 5,7 1,0 0.. 0,4 60 0.. 6 6 5,7 8
140 6,7 217 7,1 1,0 0.. 0,5 67 0.. 6 6 7,1 9
160 7,6 215 9,3 1,5 0.. 0,6 76 0.. 6 6 9,3 11
180 8,6 214 11,8 1,5 0.. 0,8 86 0.. 7 7 11,8 12
200 9,5 213 14,5 1,5 0.. 1,0 95 0.. 7 7 14,5 13
225 10,7 212 18,4 1,5 0.. 1,2 107 0.. 7 7 18,4 14
250 11,9 211 22,7 1,5 0.. 1,5 119 0.. 8 8 22,7 16
19


63 3,6 220 1,7 0,5 0.. 0,1 36 0.. 5 5 1,7 6
75 4,3 220 2,4 0,5 0.. 0,2 43 0.. 5 5 2,4 6
90 5,1 219 3,5 1,0 0.. 0,2 51 0.. 5 5 3,5 7
110 6,3 217 5,2 1,0 0.. 0,3 63 0.. 6 6 5,2 9
125 7,1 216 6,7 1,5 0.. 0,4 71 0.. 6 6 6,7 10
140 8,0 215 8,4 1,5 0.. 0,6 80 0.. 6 6 8,4 11
160 9,1 214 11, 1,5 0.. 0,7 91 0.. 7 7 11, 13
180 10,2 213 13,9 1,5 0.. 0,9 102 0.. 7 7 13,9 14
200 11,4 212 17,2 1,5 0.. 1,1 114 0.. 8 8 17,2 15
225 12,8 210 21,7 2,0 0.. 1,4 128 0.. 8 8 21,7 17
250 14,2 209 26,8 2,0 0.. 1,8 142 0.. 9 9 26,8 19


63 3,7 220 1,8 0,5 0.. 0,1 37 0.. 5 5 1,8 6
75 4,4 220 2,5 0,5 0.. 0,2 44 0.. 5 5 2,5 6
90 5,3 219 3,6 1,0 0.. 0,2 53 0.. 5 5 3,6 7
110 6,5 217 5,4 1,0 0.. 0,4 65 0.. 6 6 5,4 9
125 7,4 216 6,9 1,5 0.. 0,5 74 0.. 6 6 6,9 10
140 8,2 215 8,7 1,5 0.. 0,6 82 0.. 6 6 8,7 11
160 9,4 214 11,4 1,5 0.. 0,8 94 0.. 7 7 11,4 13
180 10,6 212 14,4 1,5 0.. 1,0 106 0.. 7 7 14,4 14
200 11,8 211 17,7 1,5 0.. 1,2 118 0.. 8 8 17,7 16
225 13,2 210 22,5 2,0 0.. 1,5 132 0.. 8 9 22,5 17
250 14,7 209 27,7 2,0 0.. 1,8 147 0.. 9 9 27,7 19


63 4,6 220 2,2 1,0 0.. 0,1 46 0.. 5 5 2,2 6
75 5,5 218 3,1 1,0 0.. 0,2 55 0.. 5 5 3,1 8
90 6,6 217 4,4 1,0 0.. 0,3 66 0.. 6 6 4,4 9
110 8,1 215 6,6 1,5 0.. 0,4 81 0.. 6 6 6,6 11
125 9,2 214 8,5 1,5 0.. 0,6 92 0.. 7 7 8,5 13
140 10,3 213 10,7 1,5 0.. 0,7 103 0.. 7 7 10,7 14
160 11,8 211 14, 1,5 0.. 0,9 118 0.. 8 8 14, 16
180 13,2 210 17,7 2,0 0.. 1,2 132 0.. 8 9 17,7 17
200 14,7 209 21,8 2,0 0.. 1,5 147 0.. 9 9 21,8 19
225 16,5 208 27,6 2,0 0.. 1,8 165 0.. 9 10 27,6 21
250 18,4 206 34,1 2,0 0.. 2,3 184 0.. 10 11 34,1 23
20


63 5,7 218 2,6 1,0 0.. 0,2 57 0.. 5 5 2,6 8
75 6,8 216 3,7 1,0 0.. 0,2 68 0.. 6 6 3,7 10
90 8,2 215 5,4 1,5 0.. 0,4 82 0.. 6 6 5,4 11
110 10,0 213 8, 1,5 0.. 0,5 100 0.. 7 7 8, 14
125 11,4 212 10,3 1,5 0.. 0,7 114 0.. 8 8 10,3 15
140 12,7 210 13, 2,0 0.. 0,9 127 0.. 8 8 13, 17
160 14,5 209 16,9 2,0 0.. 1,1 145 0.. 9 9 16,9 19
180 16,4 208 21,4 2,0 0.. 1,4 164 0.. 9 10 21,4 21
200 18,2 207 26,5 2,0 0.. 1,8 182 0.. 10 11 26,5 23
225 20,5 205 33,5 2,5 0.. 2,2 205 0.. 10 12 33,5 26
250 22,7 204 41,4 2,5 0.. 2,8 227 0.. 11 13 41,4 28


63 7,0 216 3,1 1,0 0.. 0,2 70 0.. 6 6 3,1 10
75 8,3 215 4,5 1,5 0.. 0,3 83 0.. 7 7 4,5 12
90 10,0 213 6,4 1,5 0.. 0,4 100 0.. 7 7 6,4 14
110 12,2 211 9,6 2,0 0.. 0,6 122 0.. 8 8 9,6 16
125 13,9 210 12,4 2,0 0.. 0,8 139 0.. 9 9 12,4 18
140 15,6 208 15,5 2,0 0.. 1,0 156 0.. 9 10 15,5 20
160 17,8 207 20,3 2,0 0.. 1,4 178 0.. 10 10 20,3 23
180 20,0 206 25,6 2,5 0.. 1,7 200 0.. 10 11 25,6 25
200 22,2 205 31,6 2,5 0.. 2,1 222 0.. 11 12 31,6 28
225 25,0 203 40,1 2,5 0.. 2,7 250 0.. 12 14 40,1 31
250 27,8 203 49,4 3,0 0.. 3,3 278 0.. 13 15 49,4 34


63 8,5 214 3,7 1,5 0.. 0,2 85 0.. 7 7 3,7 12
75 10,1 213 5,3 1,5 0.. 0,4 101 0.. 7 7 5,3 14
90 12,2 211 7,6 2,0 0.. 0,5 122 0.. 8 8 7,6 16
110 14,9 209 11,3 2,0 0.. 0,8 149 0.. 9 9 11,3 19
125 16,9 208 14,6 2,0 0.. 1,0 169 0.. 9 10 14,6 22
140 18,9 206 18,3 2,0 0.. 1,2 189 0.. 10 11 18,3 24
160 21,6 205 24, 2,5 0.. 1,6 216 0.. 11 12 24, 27
180 24,3 204 30,3 2,5 0.. 2,0 243 0.. 11 13 30,3 30
200 27,0 203 37,4 3,0 0.. 2,5 270 0.. 12 14 37,4 33
225 30,4 202 47,4 3,0 0.. 3,2 304 0.. 14 16 47,4 37
250 33,8 202 58,5 3,0 0.. 3,9 338 0.. 15 18 58,5 41
21
7. Welding Parameters for PP pipes & fittings DVS norm version 2207-11
material PP SDR 41 PP Cylinder section cm2 5,88
D S Temp. P1 bead P2 t2 t3 t4 P5 t5
mm mm °C bar Mm bar sec sec sec bar sec
63 1,8 210° 0,6 0,5 0,1 135 5 6 0,6 360
75 1,9 210° 0,7 0,5 0,1 135 5 6 0,7 360
90 2,2 210° 1,0 0,5 0,1 135 5 6 1,0 360
110 2,7 210° 1,5 0,5 0,2 135 5 6 1,5 360
125 3,1 210° 2,0 0,5 0,2 135 5 6 2,0 360
140 3,5 210° 2,6 0,5 0,3 135 5 6 2,6 360
160 3,9 210° 3,3 0,5 0,3 135 5 6 3,3 360
180 4,4 210° 4,1 0,5 0,4 135 5 6 4,1 360
200 4,9 210° 5,1 0,5 0,5 141 5 6 5,1 418
225 5,5 210° 6,4 0,5 0,6 151 5 6 6,4 504
250 6,1 210° 7,9 0,5 0,8 161 6 7 7,9 590
material PP SDR 33 PP Cylinder section cm 5,88
2
63 2 210° 0,7 0,5 0,1 135 5 6 0,7 360
75 2,4 210° 0,9 0,5 0,1 135 5 6 0,9 360
90 2,8 210° 1,3 0,5 0,1 135 5 6 1,3 360
110 3,5 210° 2,0 0,5 0,2 135 5 6 2,0 360
125 3,9 210° 2,5 0,5 0,3 135 5 6 2,5 360
140 4,4 210° 3,2 0,5 0,3 135 5 6 3,2 360
160 5 210° 4,1 0,5 0,4 143 5 6 4,1 432
180 5,6 210° 5,2 0,5 0,5 153 5 6 5,2 518
200 6,2 210° 6,4 0,5 0,6 162 6 7 6,4 605
225 7 210° 8,1 0,5 0,8 175 6 7 8,1 720
250 7,8 210° 10,1 1 1,0 186 6 8 10,1 797
material PP SDR 26 PP Cylinder section cm 5,88
2
63 2,5 210° 0,8 0,5 0,1 135 5 6 0,8 360
75 2,9 210° 1,1 0,5 0,1 135 5 6 1,1 360
90 3,5 210° 1,6 0,5 0,2 135 5 6 1,6 360
110 4,3 210° 2,4 0,5 0,2 135 5 6 2,4 360
125 4,9 210° 3,1 0,5 0,3 141 5 6 3,1 418
140 5,4 210° 3,9 0,5 0,4 149 5 6 3,9 490
160 6,2 210° 5,1 0,5 0,5 162 6 7 5,1 605
180 7 210° 6,5 0,5 0,6 175 6 7 6,5 720
200 7,7 210° 7,9 1 0,8 185 6 8 7,9 787
225 8,7 210° 10,0 1 1,0 199 6 8 10,0 883
250 9,7 210° 12,4 1 1,2 213 7 9 12,4 979
22
material PP SDR 17.6 PP Cylinder section cm2 5,88

mm mm °C bar mm bar sec sec sec bar sec
63 3,6 210° 1,1 0,5 0,1 135 5 6 1,1 360
75 4,3 210° 1,6 0,5 0,2 135 5 6 1,6 360
90 5,1 210° 2,3 0,5 0,2 145 5 6 2,3 446
110 6,3 210° 3,5 0,5 0,3 164 6 7 3,5 619
125 7,1 210° 4,5 1 0,4 176 6 7 4,5 730
140 8 210° 5,6 1 0,6 189 6 8 5,6 816
160 9,1 210° 7,3 1 0,7 204 6 9 7,3 922
180 10,2 210° 9,2 1 0,9 220 7 10 9,2 1027
200 11,4 210° 11,5 1 1,1 237 7 11 11,5 1142
225 12,8 210° 14,5 1 1,5 255 7 12 14,5 1269
250 14,2 210° 17,9 1 1,8 271 8 13 17,9 1389
material PP SDR 11 PE 100 Cylinder section cm 5,88
2
mm mm °C bar mm bar sec sec sec bar sec
63 5,8 210° 1,8 0,5 0,2 156 6 7 1,8 547
75 6,9 210° 2,5 0,5 0,3 173 6 7 2,5 706
90 8,2 210° 3,6 1 0,4 192 6 8 3,6 835
110 10 210° 5,3 1 0,5 217 7 9 5,3 1008
125 11,4 210° 6,9 1 0,7 237 7 11 6,9 1142
140 12,8 210° 8,7 1 0,9 255 7 12 8,7 1269
160 14,6 210° 11,3 1 1,1 276 8 13 11,3 1423
180 16,4 210° 14,3 1 1,4 298 8 15 14,3 1577
200 18,2 210° 17,7 1 1,8 319 9 16 17,7 1731
225 20,5 210° 22,4 1,5 2,2 345 9 18 22,4 1929
250 22,8 210° 27,7 1,5 2,8 368 10 20 27,7 2126
23
8. Maintenance
8.1 Basic machine
It's strongly suggested to keep always the machine clean with particular care of the bolts and the cylinder's heads .
Keep attention while insert the electric facing tool and the PTFE coated heating mirror avoiding to damage the machine's slide bars.
8.2 Facing tool

It's strongly suggested to keep always clean the blades and wash the pulleys by using a detergent.
At regular intervals carry out a complete cleaning operation with a internal lubrication as well , as per following instructions:
- Remove the carter by enlighten the screws
- Take out the shavings might be present
- Enlighten the screws and remove the pulley and carry out the cleaning and the lubrication of the bearing .
8.3 Heating mirror

Please take care on handling the heating mirror in order to avoid damages to the PTFE coating.
Keep always clean the PTFE coated surfaces, cleaning must be done with surface still warm by using a soft cloth or paper, avoiding
abrasive materials in that might damage the PTFE coated surfaces. To achieve this operation you must wear protective gloves
At regular intervals we suggest you to:
- Clean the surfaces by a quick evaporation detergent (alcohol)
- Check the tightening of the screws and the cable and plug condition
- Verify the temperature differences on the heating mirror surfaces according to the following table DVS norm 2208-1 here
following table:
WELDING SURFACE OF THE MIRROR ∆Τ1 ∆Τ2 ∆ΤΤΟΤ ∆Τ1 Maximum temperature difference on the mirror surface
< 250 cm2 5 °C 3 °C 8 °C ∆Τ2 Temperature deviation for the adjustment
250 …. 2000 cm2 7 °C 3 °C 10 °C ∆ΤΤΟΤ Maximum accepted difference on the mirror surface
2000 …. 5000 cm2 11 °C 3 °C 14 °C
5000 …. 12000 cm2 13 °C 3 °C 16 °C
> 12000 14 °C 3 °C 17 °C
8.4 Hydraulic unit

The hydraulic unit does not need particular maintenance nevertheless the following instructions must be followed:
1. Check periodically the oil level and in case add with oil type:
ESSO NUTO H 68,SHELL TELLUS 68,MOBIL DTE 26,AGIP OSO 46
The level should not be lower than 5 cm from the tank maximum level.
A checking every 15 working days it's strongly suggested.
2. Replace totally the oil every 6 months or after 500 working hours.
3. Keep clean the hydraulic unit with particular care on the tank and quick couplings.
4. Avoid to operate with rain or high humidity (95 RH %) value and temperatures below 0°C or above + 50°C.
5. During the transport it's suggested to put the metal plug instead of the plastic one.
24
9. Troubleshooting and relative solutions

9.1 Basic machine
a) The quick couplings can't be connected:
Check if there's pressure on the hoses in case bring the pressure to zero ( see relative instructions )
Check if the quick couplings are clean
b) The machine does not move in linear way:
The above mentioned situation could happen in case of clash or in case the machine with the pipe assembled in has been fiercely
moved. If the damaged part can be located proceed to the substitution, however if the trouble still remain, kindly contact the
Customer Service
c) The nut/s is/are seizure:
Replace the complete tie rod bolt
d) Oil leakage in the cylinders:
Consult the Customer Service Dept. verify if it's necessary to replace the cylinders or just the gasket
9.2 Facing tool

a) The engine does not start:
Unplug the facing tool and check the electric connections and the safety micro-switch
b) The engine is burnt out:
In case it's need to replace the engine the following operations must be done:
- Unplug the facing tool
- Enlighten the screws connecting the engine to the facing tool, disconnect the safety
micro-switch and wires
- Remove the engine by means of pulling in upper direction, remove the joint from the
drill
- Screw the joint on the new engine
- Mount the new drill engine by taking care to fix the joint gap in a proper way
- Tighten the screws connecting the engine to the facing tool, connect the safety
micro-switch and wires
c) The blades do not remove material:
Wear and tear of one cutting side enlighten the screws and turn the blades using the other side.
Wear and tear of both cutting side of the blades replace with original spare parts.
9.3 Hydraulic unit

a) The engine does not start:
Check that the hydraulic unit engine is switched on
The microswitch is damaged or wrongly adjusted
- To adjust the microswitch you must enlighten the screws show in the
- figure below and bring the lever A to position A3.
- Move the microswitch towards the internal of the hydraulic until the
engine start and tighten the fixing screw.
- Check that in position A1the engine is switched off.
- In different case adjust the microswitch position again.
b) The engine replacement:

Check that the electric plug is disconnected
Open the electric connections box and disconnect the micro-switch cable
Enlighten the screws and take out the engine
Take out the joints and insert them on the new engine
Reassemble the engine taking care that the joints are perfectly located on
the own housings
Check the anti clockwise rotation of the electric fan
25
c) If the hydraulic unit cannot increase the pressure reasons could be :

- Check the oil level
- The lever E is not closed.
- Check if they are some leakage on hydraulic circuit.
d) If the hydraulic unit cannot maintain a constant pressure reasons could be :

- The lever E is not closed.
- The accumulator is down or damaged. To replace the pressure gauge follows the below steps:
1. Bring the pressure to zero and enlighten the bolt
2. Take out the fitting and replace the damaged accumulator with the new one
3. Tighten the bolt
9.4 Hearting mirror

a) The heating mirror does not warm up:
1. Check if the light is switched off , in case check the plug
2. The light is switched on, probably a wire disconnected , check the contacts as follows:
- Take off the plug from the power
- Unscrew the nuts and take out the thermostat support
- Unscrew the screws and remove the cap
- Check all the electric connections and reassemble
- Unscrew the screws and take out the cover
- Check all the electric connections and reassemble
3. By utilizing a Tester check if all the resistances are in good condition ,if one or more are broken the heating mirror must be
changed
4. By utilizing a tester check the working of the thermostat, in case substitute
5. For additional information on electric components, please refer to our Technical Dept.
26
10. Drawings
10.1 Thermostat connection
10.2 Facing tool and hydraulic unit engines connection
27
10.3 Hydraulic plan
28
11. Exploded view and spare parts list
29
PT 250 Basic Machine , Code: PT250B PT 250 Basic Machine , Code: PT250B
Pos. Code Description Qty Pos. Code Description Qty
1 PT250B01 side support 1 29 PT250B29 Tie rod closer 8
2 PT250B02 screw TCEI UNI 5931 8.8 8x35 2 30 PT250B30 Tie rod pivot 8
3 PT250B03 Nut fixing cylinder’s tie rod 8 31 PT250B31 Screw STEI UNI 5923 45h 6x14z 8
4+5 PT250B04+05 first clamp (04+05) 1 32 PT250B32 Front nut for spacer 3
6 PT250B06 cylinder’s tie rod 8 33 PT250B33 Screw TSPEI 5933 10.9 10x45z 3
7 PT250B07 quick coupling M/F 1/4 1 34 PT250B34 H. mirror disconnecting device pin 1
8 PT250B08 Tee fitting TN 96 10 LR 2 35 PT250B35 H.mirror disconnecting dev. hooker 1
9 PT250B09 Fitting TN 126 10 LR 2 36 PT250B36 H.mirror disconnecting dev. body 1
10 PT250B10 Danger label 2 37 PT250B37 Lower Cylinder 1
11 PT250B11 Upper Cylinder 1 38 PT250B38 Oil collector hose 2
12 PT250B12 washer bonded 1/4 4 39 PT250B39 Black plastic plug 60x30 4
13 PT250B13 Technical data label 1 40 PT250B40 Covers ABS 22X2 4
14 PT250B14 Serial no. label 1 41 PT250B41 Screw TCEI UNI 5931 8.8 8x16z 4
15+16 PT250B15+16 Second clamp (15+16) 1 42 PT250B42 Fitting TN 92 10 LR (1/4) 2
17 PT250B17 35.40 FB1 bush 2 43 PT250B43 transport pipe 2
18+19 PT250B18+19 Third clamp (18+19) 1 44 PT250B44 Stop limit label 2
20 PT250B20 Back nut for spacer 3 45 PT250B45 Ground support 2
21 PT250B21 Screw TSPEI 5933 10.9 8x30z 3 46 PT250B46 rivet tt UNI 9200 3x7 all 4
22 PT250B22 Spacer 2 47 PT250B47 ITS – TECNODUE label 1
23+24 PT250B23+24 Fourth clamp c/w support (23+24) 1 48 PT250B48 blind nut UNI 5721 8 m 10 z 1
25 PT250B25 Screw TCEI UNI 5931 8.8 10x40z 2 49 PT250B49 washer UNI 6592 m 10 z 1
26 PT250B26 Beep beep coupler system 16 50 PT250B50 Third bar tie rod 1
27 PT250B27 Nut tie rods 8 51 PT250B51 Third bar 1
28 PT250B28 Washer for tie rods 8 52
PT 250 Upper Cylinder , Code: PT250B11 PT 250 Lower Cylinder , Code: PT250B37
1 PT250B1101 Gasket GHK 313 35.0 43.6 5.3 38.0 2 1 PT250B3701 Gasket GHK 313 35.0 43.6 5.3 38.0 2
2 PT250B1102 35.30 FB1 bush 2 2 PT250B3702 35.30 FB1 bush 2
3 PT250B1103 Upper cylinder head 2 3 PT250B3703 Upper cylinder head 2
4 PT250B1104 Gasket I/GR 0350 NCR 2 4 PT250B3704 Gasket I/GR 0350 NCR 2
5 PT250B1105 O-ring 3187 NBR 70 2.62x47.30 (134) 2 5 PT250B3705 O-ring 3187 NBR 70 2.62x47.30 (134) 2
6 PT250B1106 Gasket ring 2 6 PT250B3706 Gasket ring 2
7 PT250B1107 Gasket E/GR 0400 NPS 1 7 PT250B3707 Gasket E/GR 0400 NPS 1
8 PT250B1108 Cylinder’s housing 1 8 PT250B3708 Cylinder’s housing 1
9 PT250B1109 Cylinder’s stem 1 9 PT250B3709 Cylinder’s stem 1
10 PT250B1110 Stopper ring 2 10 PT250B3710 Stopper ring 2
11 PT250B1111 Screw TCEI UNI 5931 8.8 6x10 z 2
12 PT250B1112 Washer 6x12x1,5 2
Beep Beep coupler system, Code: PT250B26 PT 250 Gasket kit, Code: PT250B37KT
1 PT250B2601 Pivot for beep beep coupler system 1 1 PT250B3701 Gasket GHK 313 35.0 43.6 5.3 38.0 2
2 PT250B2602 Hook for beep beep coupler system 1 4 PT250B3704 Gasket I/GR 0350 NCR 2
3 PT250B2603 Spring for beep beep coupler system 1 5 PT250B3705 O-ring 3187 NBR 70 2.62x47.30 (134) 2
7 PT250B3707 Gasket E/GR 0400 NPS 1
30
31
PT 250 Hydraulic Unit , Code: PT160A PT 250 Hydraulic Unit , Code: PT160A
1 PT160A01 Hose R1T M 1/4 + FD 1/4 L=2500 2 39 PT160A39 Plug d. 8 1
2 PT160A02 Oil tank LT.1 1 40 PT160A40 Nipples M 1/4 1
3 PT160A03 washer ½ 1 41 PT160A41 Washer 18X1.5 1
4 PT160A04 Plug 1/2 1 42 PT160A42 accumulator L 01/8 with 20 g. oil 1
5 PT160A05 Filter UP 100 1 43 PT160A43 Hydraulic unit control label 1
6 PT160A06 Screw TCEI uni 5931 8.8 8x85 zin 2 44 PT160A44 Carter for valves protection 1
7 PT160A07 Washer grower UNI 1751 m8 z 2 45 PT160A45 Screws TBEI 10.9 6X10 z 4
8 PT160A08 Gear pump PS-1/1.25 S 1 46 PT160A46 Serial number label 1
9 PT160A09 O-ring 2037 NBR 1.78x9.25 (012) 1 47 PT160A47 Technical data label 1
10 PT160A10 O-ring 3106 NBR 2.62x26.65 (121) 1 48 PT160A48 Carter 1
11 PT160A11 O-ring 4450 NBR 3.53x113.9 (246) 1 49 PT160A49 Rivet tt uni 9200 3x7 all 4
12 PT160A12 Max pressure valve FPMDC15P35 1 50 PT160A50 ITS - TECNODUE 80X25 label 1
13 PT160A13 Pump body HY 10 K3P0-01 ¼ BB 1 51 PT160A51 Screw TC CR UNI 6954 3.5X19 zin 4
14 PT160A14 Screw TCEI uni 5931 8.8 6x35 zin 4 52 PT160A52 light switch 16A + cap 1
15 PT160A15 O-ring 2056 NBR 1.78x14.00 (015) 2 53 PT160A53 Electric danger label 1
16 PT160A16 Check valve RPC 04 / 2.5 00 00 1 54 PT160A54 Box FMA 63 / 71 1
17 PT160A17 Distributor shaft TC2 dr. C0618 1 55 PT160A55 Fan cover MEC 71 1
18 PT160A18 Distributor block HD 104 1 56 PT160A56 Fan MEC 71 1
19 PT160A19 Lever protection HD 104 1 57 PT160A57 Condenser 20MF 1
20 PT160A20 By pass valve V03/M 1 58 PT160A58 Cable H07 RNF 2G1 TITANEX 0,35
21 PT160A21 Handle 1 59 PT160A59 Engine MEC 71 HP 0.5 B14 230V 4P 1
22 PT160A22 Distributor lever HD 104 L.185 1 60 PT160A60 Cable H07 RNF 3G1 TITANEX 3
23 PT160A23 Complete distributor TC2 1 61 PT160A61 Hollow screw 1
24 PT160A24 Pressure regulating valve VEN 06 1 62 PT160A62 Plug 1/4 1
25 PT160A25 Screw TCEI UNI 5931 8.8 4x10 z 2 63 PT160A63 Pressure gauge support 1
26 PT160A26 Washer UNI 6592 m 4 zin 6 64 PT160A64 Pressure gauge D.100 range 0-100 BAR 1
27 PT160A27 Nut UNI 7473 8 m4 2 65 PT160A65 Screw TCEI UNI 5931 8.8 6x16 zin 8
28 PT160A28 Plastic cap 1 66 PT160A66 Engine flange c.a. HP 0.33/0.5 FLCA71 1
29 PT160A29 Screw TCEI UNI 5931 8.8 4x35z 2 67 PT160A67 Joint HP 0.33/0.50 1
30 PT160A30 Microswitch ASITZ 7141 1 68 PT160A68 Pump joint g. 1 x 0.27 reinf. 1
31 PT160A31 Screw STEI UNI 5923 45h 10x14 z 2 69 PT160A69 Washer fl m 10x30x2,5 zin 2
32 PT160A32 Nut UNI 5589 8 m 10 zin 1 70 PT160A70 Screw TCEI UNI 5931 8.8 10x25 zin 2
33 PT160A33 Spring latch 1 71 PT160A71 Support 18-20 4
34 PT160A34 Ball 5/16” 1 72 PT160A72 Frame 1
35 PT160A35 Washer 1/4 9 73 PT160A73 Unit model HY10 130 complete 1
36 PT160A36 Screw TCEI UNI 5931 8.8 8x70z 2 74 PT160A74 Nut DIN 6923 8 m 6 4
37 PT160A37 Generic danger label 1 75 PT160A75 quick coupling M/F 1/4 1
38 PT160A38 Connector FT 299 44 M ¼” 1
32
PT 250 Facing Tool , Code: PT250F PT 250 Facing Tool , Code: PT250F
1 PT250F01 Generic danger label 1 29 PT250F29 End connector M4 1
2 PT250F02 Electric danger label 1 30 PT250F30 Washer fl UNI m 4x12x1.5 zin 1
3 PT250F03 Plastic stub 142X3.6 2 31 PT250F31 Facing tool stopper 1
4 PT250F04 Ring UNI 7434 c70 4 2 32 PT250F32 Screw spacer 1
5 PT250F05 Bush 1 33 PT250F33 Washer fl UNI m 5x15x1,5 zin 1
6 PT250F06 Lever 1 34 PT250F34 Insulating pipe 1.5mm2 P=8MM red 3
7 PT250F07 Pivot 1 35 PT250F35 Screw TCEI UNI 5931 8.8 5x25 z 1
8 PT250F08 Nut 1 36 PT250F36 Cable H07 RNF 3G1,5 TITANEX 3,3
9 PT250F09 Spring 1 37 PT250F37 Cable stopper PG11 1
10 PT250F10 Facing tool stopper pivot 1 38 PT250F38 Screw TCEI UNI 5931 8.8 4x10 zin 5
11 PT250F11 Cable H07 RNF 3G1 0,6 39 PT250F39 Serial no. label 1
12 PT250F12 Double insulating pipe 2x2.5mm2 P=10MM blue 1 40 PT250F40 Technical data label 1
13 PT250F13 Cable stopper PG11 163/11 2 41 PT250F41 Box cover 1
14 PT250F14 Switch 1 42 PT250F42 Terminal mm2 2,5 3
15 PT250F15 Screw TCEI UNI 5931 8.8 5x35 zin 2 43 PT250F43 Terminal mm2 4 1
16 PT250F16 Cable holder 604 / 6 1 44 PT250F44 Double ins. pipe 2X1.5mm2 P=8MM black 3
17 PT250F17 Screw UNI 6107 4.8 3x8z 2 45 PT250F45 Cable stopper PG9 163/9 1
18 PT250F18 Wheel for reducing gear 1 46 PT250F46 Stopper 1
19 PT250F19 3 holes blade 2 47 PT250F47 Screw TCEI UNI 5931 8.8 8x45 zin 1
20 PT250F20 Screw tspi UNI 6109 4x12 a2 6 48 PT250F48 Right disk 1
21 PT250F21 Screw TCEI UNI 5931 8.8 8x60 2 49 PT250F49 Bearing 51100 1
22 PT250F22 Left disk 1 50 PT250F50 Bearing 6002 ZZ 1
23 PT250F23 Screw TSPEI 5933 10.9 5x12 z 6 51 PT250F51 Screw for reducing gear 1
24 PT250F24 Flange 1 52 PT250F52 Bearing 6003 ZZ 1
25 PT250F25 Bearing 16008 2 53 PT250F53 Ring UNI 7437 c 70 35 1
26 PT250F26 Rivets tt UNI 7346 2,5x6,5 brass 4 54 PT250F54 Drill joint 1
27 PT250F27 label ITS - TECNODUE 80X25 1 55 PT250F55 drill PERLES PSB 7 1
28 PT250F28 Facing tool body PT 160 1
33
PT 250 Heating Mirror , Code: PT250T PT 250 Heating Mirror , Code: PT250T
1 PT250T01 Thermometer 1 30 PT250T30 Screw TCEI UNI 5931 8.8 4x10Z 2
2 PT250T02 o-ring 2200 NBR 1.78x50.52 (033) 1 31 PT250T31 Relay 230 VAC 30A 1
3 PT250T03 Danger and compulsory label 3 32 PT250T32 Nut UNI 5588 m 4 zin 2
4 PT250T04 Screw TCEI UNI 5931 a2 5x12 2 33 PT250T33 Red female connector 6.35x0.8 2
5 PT250T05 Thermometer holder cover 1 34 PT250T34 Yellow insulating pipe 1 mm2 P=8MM 8
6 PT250T06 Insulating red pipe D.5 1.5V 0,2 35 PT250T35 Red insulating pipe 1,5 mm2 P=8MM 7
7 PT250T07 O-ring 2400 NBR 70 1.78x101.32 (045) 1 36 PT250T36 3 studs terminal 1
8 PT250T08 Screw TCEI UNI 5931 a2 5x30 8 37 PT250T37 5 studs terminal 1
9 PT250T09 Washer grower UNI 1751 m5 z 8 38 PT250T38 Black flame retardant wire 1 mm2 2
10 PT250T10 terminal mm2 2,5 7 39 PT250T39 Nut ISO M25x1.5 CE 1
11 PT250T11 terminal 4/6 mm2 3 40 PT250T40 Brass nut PG11 169/11 1
12 PT250T12 Red cap for wire 2x1mm2 6 41 PT250T41 Washer UNI 6593 m 4 4
13 PT250T13 Handle with hole for cable st. 1 42 PT250T42 Nut UNI 7473 8 m 4 4
14 PT250T14 Cable stopper M25 2 43 PT250T43 Cable stopper PG11 1
15 PT250T15 Cable H07 RNF 7G1,5 TITANEX 3,3 44 PT250T44 Cable H07 RNF 3G1,5 TITANEX 3,3
16 PT250T16 Heating plate PT 250 1 45 PT250T45 Female terminal 4
17 PT250T17 Gasket 4 46 PT250T46 Nut UNI 5588 m 3 brass 4
18 PT250T18 Probe PT100 2+2 wires 1 47 PT250T47 Connector UTG 012-8S 1
19 PT250T19 Spacer 1 48 PT250T48 Connector 8 pins 1
20 PT250T20 Gasket 4 49 PT250T49 Screw TSPI UNI 6109 3x12 brass 1
21 PT250T21 Box 1 50 PT250T50 Screw TCI UNI 6107 3x10 brass 3
22 PT250T22 Rubber handle D. 30 1 51 PT250T51 Black plastic stub 99x2.5 6
23 PT250T23 Thermostat TLK38 1 52 PT250T52 Ring 3.5 type 0 1
24 PT250T24 Electric danger label 1 53 PT250T53 Ring 3.5 type 1 5
25 PT250T25 ITS – TECNODUE 80X25 label 1 54 PT250T54 Ring 3.5 type 2 2
26 PT250T26 Technical data label 1 55 PT250T55 Ring 3.5 type 3 1
27 PT250T27 Serial no. label 1 56 PT250T56 Ring 3.5 type 5 1
28 PT250T28 Thermostat box 1 57 PT250T57 Gasket for TLK38 thermostat 33X74 1
29 PT250T29 Screw TC CR 7687 4.8 4x16 zin 4
34
PT 250 Stub Device , Code: PT250S PT 250 Stub Device , Code: PT250S
1 PT250S01 Plateau PT 250 1 6 PT250S06 Fixing stub end bracket 2
2 PT250S02 Cursor 4 7 PT250S07 Screw STEI UNI 5927 45h 5x8 zin 2
3 PT250S03 Screw STEI UNI 5927 45h 8x35 zin 4 8 PT250S08 Upper stopper 2
4 PT250S04 Bracket 2 9 PT250S09 Screw STEI UNI 5923 45h 8x20 2
5 PT250S05 screw TCEI UNI 5931 8.8 8x20 zin 4 10 PT250S10 Screw for fixing s.e. braket 2
PT 250 Tools kit, Code: PT250TK PT 250 Tools kit, Code: PT250TK
1 PT160TK01 Screw TCEI UNI 5931 8.8 6x50 zin 8 5 PT160TK05 Setscrew wrench UNI 6753 s 6 1
2 PT160TK02 Socket wrench 1 6 PT160TK06 Plug ½ for hydraulic unit 1
3 PT160TK03 Setscrew wrench UNI 6753 s 4 1 7 PT160TK07 Screw driver 1
4 PT160TK04 Setscrew wrench UNI 6753 s 5 1
PT 250 Support, Code: PT250U PT 250 Support, Code: PT250U

1 PT250U01 Support 1 2 PT250U02 Black plug 60x30 4
PT 160 Half reduction PT 250 Short spigot fit. clamp, Code: PT250G
Pos. Description Qty Pos. Code Description Qty
Half wide ring av. sizes:
1 63,75,90,110,125,140,160,180,200,225mm 1 PT250G02 Short Spigot fittings clamp 1
Half narrow ring av. sizes:
2 63,75,90,110,125,140,160,180,200,225mm
35
This manual has been printed on December 2008

The technical data and information contained in this manual can be changed without any notice
36

Tecnodue PT250 User Manual

Uploaded by

Copyright:

Available Formats

Tecnodue PT250 User Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Tecnodue PT250 User Manual

Uploaded by

Copyright:

Available Formats

I.T.S.

I.T.S. Ital Trade Services S.r.l.

SAFETY RULES ACCORDING TO DIRECTIVES CEE

Label on machine’s components

WEAR BURNS ELECTRIC SQUASHING

2. General description and application field

2.1 Basic machine

The basic machine is composed by:

2.2 Facing Tool

2.3 Heating Mirror

2.3.1 Electronic thermostat – different functions

Temperature of the welding mirror for welding PE DVS 2207-1 norm

2.4 Hydraulic Unit

The basic components of the hydraulic unit are the following:

2. 4.1 Hydraulic Unit Controls

2.4.2 How to use the hydraulic unit

3. Heating mirror disconnecting device

1. Configuration 2 moveable clamps + 2 fixed clamps

3.1 Beep-beep inserts reductions

To use a beep-beep insert reduction

To use a beep-beep reduction, fix it by lightly pushing

To remove the beep-beep reduction

To safely remove the beep-beep reduction by means

4. Butt welding in brief

4.2 Machine's preparation

b) Connect the flexible hoses of the hydraulic unit to the machine

4.3 Pipes positioning into the machine and facing operation

Outside diameter Port

4.4 Inertial pressure measurement

4.5 Welding cycle

The welding phase is composed by 5 phases with 5 different times:

Pressure-Time diagram for butt welding

Total machine cylinders section( cm2 )

Material thrust coefficient for PE s 63 1,5 Kg./cm2

Optical checking of butt welding result

mm mm (minimum values) s S (maximum time) s Min (minimum values)

As per drawing above the time T corresponds to wall thickness value X in

6. Welding Table for PE pipes DVS norm version 2207-1

mm mm °C bar mm bar sec sec sec bar min

mm mm °C bar mm bar sec sec sec bar min

mm mm °C bar mm bar sec sec sec bar min

material PE80-100 SDR 26

mm mm °C bar mm bar sec sec sec bar min

material PE80-100 SDR 22

mm mm °C bar mm bar sec sec sec bar min

material PE80-100 SDR 21

mm mm °C bar mm bar sec sec sec bar min

Warning!: in case of PE100 welding, temperature T must be increased to 220°c

material PE80-100 SDR 17,6

mm mm °C bar mm bar sec sec sec bar min

material PE80-100 SDR 17

mm mm °C bar mm bar sec sec sec bar min

material PE80-100 SDR 13,6

mm mm °C bar mm bar sec sec sec bar min

Warning!: in case of PE100 welding, temperature T must be increased to 220°c

material PE80-100 SDR 11

mm mm °C bar mm bar sec sec sec bar min

material PE80-100 SDR 9

mm mm °C bar mm bar sec sec sec bar min

material PE80-100 SDR 7,4