06 DM - OC2505 - E01 - 1 OTN ODUK1+1 Protection Configuration 31P

OTN ODUK 1+1 Protection
Configuration
Networking
 A project is a ring network which is composed of three sites of

ZXONE 9700. NEC is OADM site, A and B are OTM sites
Networking Diagram
2
© ZTE Corporation. All rights reserved
Signal Flow
 Configure electrical layer ODUK 1+1 protection between NE A

and NE B
3
Configuration Steps
Preparation Create Protection Subnet
Install Boards set Protection

attribute
Wavelength
Tuning
Find Protection
Fiber Relations
Connection
Configure Service Modify

Mapping Protection
Parameters
Configure Cross
Connection
Discover Result
Service Verification
4
Install Boards
 To install the needed boards, refer to “Networking Diagram”

and “Signal Flow Diagram”.
 The boards can be discovered automatically in EMS.
5
Wavelength Tuning
6
Wavelength Tuning
 In the Topology view, right-click NE, select NE Manager, in the

Customized Resource navigation tree, select the service board.
 In the Board Operation navigation tree, select WDM Wavelength

Management > Wavelength Adjustment and Tuning, refresh and
apply.
 Notes: This step is only for line cards that support wavelength
tuning.
7
Fiber Connection
 To create fiber connection information, refer to “Networking

Diagram” and “Signal Flow Diagram” .
 The port and the order should be consistent with the equipment.
If the port is wrong, the path cannot be found, and the wrong
connection order will lead to abnormal switching.
8
Configure Service Mapping
9
 In Topology View, double-click NE, select the client service

board , right-click NE Manager, in the NE Operation navigation
tree, select WDM Service Configuration ,and set service mapping.
 Notes: Choose the Service Type, Map Mode and ODUk Type.
10
11
 In Topology View, double-click NE, select the line service board ,

right-click NE Manager, in the NE Operation navigation tree,
select WDM Service Configuration, and set the service mapping.
 Notes: Choose the Service Type, Map Mode and ODUk Type.
12
Configure FEC Mode
13
Configure FEC Mode
 In Topology View, double-click NE, select the line service board ,

right-click NE Manager, in the NE Operation navigation tree,
select WDM Service Configuration, and set FEC Mode.
 Notes: Choose the FEC Mode. For the end to end service signal,
the FEC Mode of both ends must be consistent.
14
Configure Cross Connection
15
Configure Cross Connection
 In Topology View, right-click NE. Select NE Manager. In the NE

Operation navigation tree, select Common Configuration > Cross
Connection, choose in the Group Selection and Edit, set bidirection, and
1A2Z properties for the cross connection.
 Firstly, click the client board OAC_in port, and connect to the line board
corresponding port in working path, click OK.
 Secondly, click the client board OAC_in port again, and connect to the
line board corresponding port in protection path, click OK and
ApplyPart.
 Then four lines are displayed. Three lines are green, and one line is blue.
Otherwise, check whether previous steps are correct.
 ALL the above configuration should be set on both ends of the service.
16
Discover Service
17
Discover Service
 In the Service View, select Discover Service Automatically.

 After the auto discovery, select the connection between the NEs.
All the automatic discovery paths are displayed, ensure the OTS,
OMS, OCH paths, and the configured service paths (such as
ODUK path) are there. Otherwise, check whether previous steps
are correct.
 Right-click the path from the service list, select Service Explorer,
check whether the service route information is correct. If not,
check whether previous steps are correct.
18
Set ODUK 1+1 Protection Attribute
19
Set ODUK 1+1 Protection Attribute

Connection, choose in the Group Selection and Edit. In the main
window, four lines are displayed. Click the blue line and click the
Attribute button.
 In the attribute window, set Cross connection label, the WTR times,
Enable, Return mode, Switch type, APS signal tunnel and protect
mode config. Click OK and Applypart.
 Notes: The Cross connection label and protect mode config are
default usually. The APS signal tunnel only need to be set when the
switch type is set as Bidirection.
 ALL the above configuration should be set on both ends of the
service.
20
Check SNCP Manager
21
Check SNCP Manager

Connection. In the main window, click the SNCP manager in the
bottom.
 In the SNCP manager window, some status of ODUK 1+1
protection are displayed.
 Maintenance item shows the external commands of the
Protection Group. If no external command is set, Maintenance
shows clear switch.
 Switch state shows the current actual status of the Protection
Group. In general, the state shows normal or switch. If the EMS
can not get the state, it shows not clear.
22
Check SNCP Manager
 Working /Protection channel states show the current state of two

path. The state normally shows OK. If some alarm occur in path,
it shows SF. If signal degradation occur in path, it shows SD.
 Protection effect normally shows Protection effect started. If the
protection is forbidden, it shows Protection effect Paused.
 In the light bottom of the window, the Protection effect item can
enable or disable the Protection by selecting one of the two
options.
 Notes: The protection group should be clicked firstly, or the
Protection effect item can not be handled.
23
Check SNCP Manager
 In the bottom right corner of the window, select all means to select all
the Protection groups in the window. Auto refresh means the state of
protection groups will refresh automatically. Clicking refresh item will
refresh the selected Protection groups manually.
 Switch item can give the selected Protection groups different external
commands by different options.
 Treaty Reset item can reset the Protection protocol of the selected
Protection groups when the Protection is forbidden. After the Treaty
Reset is executed, the previous state of Protection and external
commands will be cleared, and the protection will work like a new one.
 No Treaty Switch item can order PSK board directly to switch only one
selected Protection group without the APS when the Protection is
forbidden.
24
Configure ODUK 1+1 Protection
25
26
27
28
 Open Protection View, click Search PSN. IN the Search PSN

window, click Search PSN.
 In the Protection Sub-Net, the ODUk 1+1 PSN will be displayed.
Otherwise, check whether previous steps are correct.
 Select the Protection Sub-Net, and click Protection PSN. There
are three items: Attribute, Protect Parameter, Protect Relation.
 In Protect Parameter, some property of the PSN can be modified.
 In Protect Relation, some status of the working/Protecting path
are displayed, including Channel status, Command status, Switch
status and WTR status.
29
Result Verification
 1. Verify the protection subnet in Protection View.

 2. Deliver the protection switching command, and check whether
the switching is normal.
 3. Pull the fiber out of the equipment, and check whether the
switching is normal. Check whether the switching event is
correctly reported.
30

06 DM - OC2505 - E01 - 1 OTN ODUK1+1 Protection Configuration 31P

Uploaded by

Copyright:

Available Formats

06 DM - OC2505 - E01 - 1 OTN ODUK1+1 Protection Configuration 31P

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

06 DM - OC2505 - E01 - 1 OTN ODUK1+1 Protection Configuration 31P

Uploaded by

Copyright:

Available Formats

OTN ODUK 1+1 Protection

 A project is a ring network which is composed of three sites of

 Configure electrical layer ODUK 1+1 protection between NE A

Install Boards set Protection

Configure Service Modify

 To install the needed boards, refer to “Networking Diagram”

 In the Topology view, right-click NE, select NE Manager, in the

 In the Board Operation navigation tree, select WDM Wavelength

 To create fiber connection information, refer to “Networking

 In Topology View, double-click NE, select the client service

 In Topology View, double-click NE, select the line service board ,

 In Topology View, double-click NE, select the line service board ,

 In Topology View, right-click NE. Select NE Manager. In the NE

 In the Service View, select Discover Service Automatically.

 In Topology View, right-click NE. Select NE Manager. In the NE

 In Topology View, right-click NE. Select NE Manager. In the NE

 Working /Protection channel states show the current state of two

 Open Protection View, click Search PSN. IN the Search PSN

 1. Verify the protection subnet in Protection View.

You might also like