Pipe Support Fluor PDF Free

MIN.
150
3/4 " DIA. HILTI HIT HY 150 5/8" dia. A325 BOLTS C/W
ADHESIVE ANCHORS (TYP.) NUTS & LOCK WASHERS
SUPPORT COMPONENT SUPPORT COMPONENT SEE NOTE 1

AS SPECIFIED AS SPECIFIED
305
200 50 50
150
150
25mm dia. HOLES 18mm dia. HOLES
20mm THK. PLATE 20mm THK. PLATE
TWO-BOLT CONCRETE HANGER PLATE TWO-BOLT STEEL HANGER PLATE

13.3 kN MAX. LOAD 13.3 kN MAX. LOAD
305
200 50 50
200
200
305
305
25mm dia. HOLES 18mm dia. HOLES
20mm THK. PLATE 20mm THK. PLATE
FOUR-BOLT CONCRETE HANGER PLATE FOUR-BOLT STEEL HANGER PLATE
26.6 kN MAX. LOAD 26.6 kN MAX. LOAD
NOTES
1. WHEN ATTACHED TO UNDERSIDE OF AN EXISTING W SHAPE, SPACING BETWEEN BOLTS

SHOULD MATCH THE USUAL GAUGE OF THE BEAM.
SUPPORT HANGER PLATE /

TAG MATERIAL
758A TWO-BOLT / C.S.
758B FOUR-BOLT / C.S.
758AS TWO-BOLT / 316 S.S.
758BS FOUR-BOLT / 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
REV. BY REVISION APP. DES. DESIGNATION

J.M.D./T.G.
DATE
0 T.G. ISS’D FOR CONSTRUCTION H.L. CH. Y.T.

EXTRA STEEL- HANGER PLATE
03/28/95
1 T.G. REF. STANDARDS ADDED DESIGN STANDARD NO. REV.

SUP. H.LESKIE
10/22/04 DESIGNATION REVISED
DATE 03/28/95 DS-PS-X758 1

*DATE*TIME* CADD FILE No. PSP108\CAD\250\PIPE SUPPORT STANDARDS\DSPSX758.DGN
WHERE A PIPE SUPPORT STANDARD INDICATES THAT ELEVATIONS OR DIMENSTONS
ARE TO BE SPECIFIED "ON DWG", THIS INFORMATION SHALL BE GIVEN ON A LINE
ADJACENT TO THE FRAME.
EXAMPLE IDENTIFICATION
PS# WHERE "#" DENOTES THE PIPE SUPPORT

PS#
NUMBER ON THE ISOMETRIC.
eg. PS1, PS2, ETC.
PS-S612 SUPPORT,
PS-S612
DESIGN STANDARD NUMBER
DIM L = 250 DS-PS-S612
L DIMENSION "L" AS SPEC.

ON SUPPORT DETAIL.
3.2 MULTIPLE COMPONENT SUPPORTS
SOME SUPPORT ASSEMBLIES WILL REQUIRE TWO OR MORE FRAMES. EACH FRAME WILL
INDICATE THE DIFFERENT COMPONENT OF THE SUPPORT.
PS5 FIFTH PIPE SUPPORT

PS5
ON THE ISOMETRIC.
PS-S608 SUPPORT,
PS-S608
DS-PS-S608
PS6 SIXTH PIPE SUPPORT

PS6
ON THE ISOMETRIC.
PS-DA251 DIRECTIONAL ANCHOR,

PS-DA251
DS-PS-DA251
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS

J.M.D./T.G.
DATE
0 T.G. ISS’D FOR CONSTRUCTION H.L. CH. Y.T. SUPPORT DESIGNATION SHT. 2 OF 4
03/28/95
1 J.H. EXAMPLE 3.2 REVISED Y.T. SUP. DESIGN STANDARD NO. REV.
H.LESKIE
12/01/97
YY/MM/DD
DATE 03/28/95 DS-PS-101 1
*DATE*TIME* CADD FILE No. PSP108\CAD\250\PIPE SUPPORT STANDARDS\DSPS101.DGN
3.3 EXTRA SUPPORT STEEL
PIPE SUPPORT ASSEMBLIES INCORPORATING EXTRA STEEL ARRANGEMENTS OF THE

TYPES SHOWN IN THE PIPE SUPPORT STANDARDS SHALL HAVE A SECOND FRAME
INDICATING THE ARRANGEMENT TYPE AND STEEL DESIGNATION CODE.
X755 EXTRA STEEL,

PS-X755
DS-PS-X755
HEIGHT = 1650
DIM L = 1000
DIM A = 350 HEIGHT DIMENSION "H" AS SPEC.
ON SUPPORT DETAIL.
A, L DIMENSION "A" AND "L" AS SPEC.

ON SUPPORT DETAIL.
X702B-9 EXTRA STEEL,

PS-X702B-9
DS-PS-X702
DIM L = 2000
DIM A = 500
"B" FOR BOLTED CARBON STEEL MEMBER
"9" FOR STEEL CODE NUMBER 9
A, L DIMENSION "A" AND "L" AS SPEC.

ON SUPPORT DETAIL.
3.4 MULTIPLE PIPE SUPPORTS
WHERE SEVERAL PIPES ARE SUPPORTED BY A SINGLE EXTRA STEEL SUPPORT ASSEMBLY,
THE ISOMETRIC OF ONE PIPE WILL INCLUDE A FRAME TO CALL OUT THE EXTRA STEEL.
THE ISOMETRICS OF ALL OTHER PIPES SUPPORTED BY THIS EXTRA STEEL WILL SHOW
A FRAME DENOTING THE EXTRA STEEL AS "REF".
EXAMPLE
SUPPORT:
DS-PS-S603 PIPE 1 2 3 EXTRA STEEL:
(TYP. 3X) DS-PS-X703
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS

J.M.D./T.G.
DATE
03/28/95
H.LESKIE
12/01/97
DATE 03/28/95 DS-PS-102 1

3.4 ISOMETRIC FOR PIPE #1:
PS-S603 SUPPORT,
PS-S603
DS-PS-S603
PS-X703 EXTRA STEEL,

PS-X703
DS-PS-X703
ISOMETRIC FOR ALL OTHER PIPES:
PS-S603 SUPPORT,
PS-S603
DS-PS-S603
PS-X703 (REF) REFERENCE TO

PS-X703 (REF)
EXISTING EXTRA STEEL
3.5 SPECIAL SUPPORT DETAILS
SPECIAL PIPE SUPPORTS THAT DO NOT CONSIST OF ELEMENTS CONTAINED IN THE

SUPPORT STANDARDS SHALL BE DETAILED ON A SEPARATE SUPPORT DRAWING.
AN UNIQUE ITEM CODE WILL BE ASSIGNED TO EACH SPECIAL SUPPORT DETAIL.
IN THESE CASES, THE FRAME ON THE ISOMETRIC SHALL REFERENCE THE ITEM CODE.
SD-100 UNIQUE ITEM

SD-100
CODE ASSIGNED
TO SPECIAL SUPPORT DETAIL.
SUPPORTS CONSISTING OF COMBINATIONS OF STANDARD TYPES AND SPECIAL DETAILS

SHALL BE SHOWN COMPLETE IN THE DETAILS RATHER THAN USING FRAMES WHICH
ATTEMPT TO DENOTE THE MIXED TYPES.
AN EXCEPTION TO THE ABOVE IS MULTIPLE PIPE SUPPORT CASES SIMILAR TO 3.3

WHERE IT IS PERMISSIBLE TO HAVE A SPECIAL DETAIL OF THE SUPPORT STEEL
AND USE STANDARD FRAMES FOR THE INDIVIDUAL PIPE SUPPORTS.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS

J.M.D./T.G.
DATE
03/28/95
H.LESKIE
12/01/97
2 D.K.
11/18/05
EXAMPLE 3.5 REVISED B.C. DATE 03/28/95 DS-PS-103 2
ENGINEERING DATA
LOAD CARRYING CAPACITIES OF THREADED ASTM A 36 CARBON STEEL ROD
MAXIMUM SAFE LOADS, (kN)

NOM. ROD TEMPERATURE OF 340^C
ROD
DIA. FIELD SHOP
THREADED THREADED
3/8" 2.7
1/2" 5
5/8" 8
SEE NOTE 3
3/4" 12
7/8" 16.7
1" 22
1 1/4" 35.5
1 1/2" 51.7
1 3/4" 69.8
2" 92
2 1/4" 121
SEE
NOTE 2 149
2 1/2"
2 3/4" 185
3" 225
NOTES
1. HANGER ROD DIAMETER, IF NOT SPECIFIED WITH PIPE SUPPORT SELECTION, SHALL
BE IN ACCORDANCE WITH THE TABLE ABOVE.
2. HANGER RODS 1 3/4" dia. AND LARGER SHALL BE SHOP THREADED.
3. IN NO CASE SHALL HANGER RODS LESS THAN 3/8" dia. BE USED FOR SUPPORT OF PIPE
2" dia. AND SMALLER, OR LESS THAN 1/2" dia. ROD FOR SUPPORTING PIPE 2 1/2" dia. AND
LARGER.
4. TEMPERATURE OF HANGER ROD SHALL BE BASED ON A TEMPERATURE GRADIENT OF

37^C PER 25mm DISTANCE FROM THE OUTSIDE SURFACE OF THE PIPE.
5. WHEN SELECTING HANGER RODS FOR DOUBLE RISER LUGS & DOUBLE TRUNNIONS
ON RISERS USED FOR RIGID HANGERS, THE SIZE OF A SINGLE ROD SHALL
BE BASED ON THE TOTAL RISER LOAD AS ONLY ONE OF THE TWO RODS MAY
CARRY THE TOTAL LOAD.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS

J.M.D./T.G.
DATE
0 T.G.
03/28/95
ISS’D FOR CONSTRUCTION H.L. CH. Y.T. HANGER DATA
1 T.G. NOTES 1 & 5 REVISED SUP. DESIGN STANDARD NO. REV.
H.LESKIE
03/19/96
DATE 03/28/95 DS-PS-113 1

PIPE CLAMPS
THE FOLLOWING SHEETS CONTAIN VARIOUS CLAMP DIAGRAMS WITH SPECIFIC APPLICATIONS.
THEY ARE NOTED BY A FIGURE NUMBER. SOME ARE RELATED TO OTHER SUPPORT ITEMS
WHICH ARE TO BE FOUND IN THEIR PERTINENT DESIGN STANDARDS.
NOTES FOR THE PIPE CLAMP FIGURES IN THIS STANDARD ARE FOUND BELOW.
NOTES
1. CLAMP SHALL MATCH THE OUTSIDE DIAMETER OF PIPE AS SPECIFIED IN PIPING

CLASSIFICATION STANDARDS. FOR S.S. PIPING, A WOVEN HEAT-RESISTANT FABRIC
SUCH AS 1/16" THK "THERMOFAB" CLOTH TAPE MANUFACTURED BY ALBION
INDUSTRIAL PRODUCTS OR APPROVED EQUAL MUST BE BONDED TO INSIDE OF
CLAMP. THE WIDTH SHALL BE EQUAL TO THE CLAMP WIDTH.
2. DIMENSIONS "C" AND "D" ARE RECOMMENDED ONLY AND MAY BE MODIFIED
PROVIDING LOAD CARRYING CAPACITIES ARE MAINTAINED WITH A MINIMUM
SAFETY FACTOR OF 5.
3. HANGER ROD DIAMETER IF NOT SPECIFIED WITH PIPE SUPPORT SELECTION

SHALL BE IN ACCORDANCE WITH PIPE CLAMP SELECTION TABLES ON
DS-PS-121, DS-PS-122 & DS-PS-125.
4. HANGER RODS 1 3/4" DIA. AND LARGER SHALL BE SHOP THREADED.
5. IN NO CASE SHALL HANGER RODS LESS THAN 3/8" DIA. BE USED FOR
FOR SUPPORT OF PIPE.
6. TEMPERATURE OF HANGER ROD SHALL BE BASED ON A TEMPERATURE GRADIENT

37^C PER 25mm DISTANCE FROM THE OUTSIDE SURFACE OF THE PIPE.
7. CARBON STEEL PIPE CLAMPS MAX. LOAD RANGE GIVEN FOR 340^C. FOR HIGHER
TEMPERATURES UP TO 400^C, USE 87% OF LOAD SHOWN.
8. RISER CLAMPS PER DS-PS-123 AND 124 SHALL BE USED AS FOLLOWS:

- TO SUPPORT PIPE LINES 6" DIA. AND LARGER.
- TO SUPPORT LOADS THAT REQUIRE A ROD 3/4" AND LARGER.
9. VERTICAL STAINLESS STEEL PIPE LINES REQUIRING RISER CLAMP SUPPORTS

SHALL BE REINFORCED AS SPECIFIED OR WITH STAINLESS STEEL HALF-PIPE
SEGMENTS MADE FROM PIPE OF EQUAL DIAMETER, THICKNESS AND MATERIAL AS
THE PIPELINE ITSELF.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-121, DS-PS-122, DS-PS-123, DS-PS-124, DS-PS-125
J.M.D./T.G.
DATE
0 T.G.
03/28/95
ISS’D FOR CONSTRUCTION H.L. CH. Y.T. HANGER DATA
1 T.G. NOTES 3 REVISED Y.T. SUP. DESIGN STANDARD NO. REV.
H.LESKIE
03/19/96
2 T.G.
10/22/04
REF. STANDARDS ADDED DATE 03/28/95 DS-PS-120 2
"R"
"D"
"C" STOCK SIZE
PI
PE
O.
D.
"D"
SPACER FOR
FIG. 216 ONLY
ANVIL INTL. FIG. 212, FIG. 216 & FIG. HS-42SD.

TW0 BOLT PIPE CLAMP
CARBON STEEL ASTM A36 OR EQUAL
MODERATE LOADS HEAVY LOADS

ANVIL INTL. FIG. 212 OR EQUAL ANVIL INTL. FIG. 216, FIG. HS-42SD OR EQUAL
NOM STOCK CAPACITY RECOM. STOCK CAPACITY RECOM.

PIPE "D" SIZE IN (kN) ROD SIZE "D" SIZE IN (kN) ROD SIZE
DIA. "C" TO 340^C "R" "C" TO 340^C "R"
Note 1 Note 2 Note 2 Note 7 Note 3 Note 2 Note 2 Note 7 Note 3
1/2" 3/8" 1/8" x 1" 2.2 3/8"

3/4" 3/8" 1/8" x 1" 2.2 3/8"
1" 3/8" 1/8" x 1" 2.2 3/8"
1 1/4" 3/8" 1/8" x 1" 2.2 3/8"

1 1/2" 3/8" 1/8" x 1" 3.5 1/2"
2 3/8" 1/4" x 1" 4.6 1/2"
2 1/2" 1/2" 1/4" x 1" 4.6 1/2"

3" 1/2" 1/4" x 1" 4.6 1/2" 3/4" 3/8" x 2" 15 7/8"
4" 5/8" 1/4" x 1 1/4" 4.6 5/8" 7/8" 3/8" x 2" 15.6 7/8"
5" 5/8" 1/4" x 1 1/4" 4.6 5/8" 7/8" 3/8" x 2" 15.6 7/8"
6" 3/4" 3/8" x 1 1/2" 7.2 3/4" 1" 1/2" x 2 1/2" 21.6 1"
8" 3/4" 3/8" x 1 1/2" 7.2 3/4" 1" 1/2" x 2 1/2" 21.6 1"
10" 7/8" 1/2" x 2" 11 7/8" 1 1/4" 5/8" x 2 1/2" 26.6 1 1/8"
12" 7/8" 1/2" x 2" 11 7/8" 1 1/2" 3/4" x 3" 38.5 1 1/2"
14" 7/8" 1/2" x 2 1/2" 11 1" 1 1/2" 3/4" x 3 1/2" 40.5 1 1/2"
16" 7/8" 7/8" 11 1" 1 1/2" 3/4" x 3 1/2" 40.5 1 1/2"
18" 1" 5/8" x 2 1/2" 13.6 1" 1 1/2" 3/4" x 3 1/2" 61.3 1 3/4"
20" 1 1/8" 5/8" x 2 1/2" 13.6 1 1/4" 1 1/2" 3/4" x 3 1/2" 68 2"
24" 1 1/4" 5/8" x 3" 13.6 1 1/4" 2 1/4" 1" x 6" 72.5 2"
28" 2 1/4" 1" x 8" 80 2"
30" 1 1/2" 3/4" x 4" 15.5 1 1/2" 2 1/2" 1 1/4" x 7" 91.1 2"
32" 2 1/2" 1 1/4" x 8" 105.6 2 1/4"
34" 2 1/2" 1 1/4" x 8" 111 2 1/4"
36" 2 3/4" 1 1/2" x 8" 124.5 2 1/2"
40" 3" WIDTH= 10" 155 2 3/4"
42" 2 3/4" 1 3/4" x 10" 155 2 3/4"
48" 3" WIDTH= 10" 155 2 3/4"
FOR REFERENCE NOTES, SEE DESIGN STANDARD DS-PS-120.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-120
J.M.D./T.G.
DATE
0 T.G.
03/28/95
ISS’D FOR CONSTRUCTION H.L. CH. Y.T. PIPE CLAMP DATA
T.G. "GRINNELL" CHG’D TO "ANVIL INTL." DESIGN STANDARD NO. REV.
1 SUP. H.LESKIE
10/22/04 REF. STANDARDS ADDED
DATE 03/28/95 DS-PS-121 1

"R"
"D"
SPACER
INSULATION
PE
PI
D.
O.
"C" STOCK SIZE
"D"
ANVIL INTL. FIG. 295, FIG. 295H & FIG. HS-41SD
THREE BOLT PIPE CLAMP
MODERATE LOADS HEAVY LOADS

ANVIL INTL. FIG. 295 OR EQUAL ANVIL INTL. FIG. 295H, FIG. HS-41SD OR EQUAL
RECOM. RECOM.
STOCK CAPACITY STOCK CAPACITY
NOM ROD ROD
"D" SIZE IN (kN) "D" SIZE IN (kN)
PIPE SIZE SIZE
"C" TO 340^C "C" TO 340^C
DIA. "R" "R"
Note 1 Note 2 Note 2 Note 7 Note 3 Note 2 Note 2 Note 7 Note 3
3/4" 3/8" 3/16" x 1" 4.2 1/2"

1" 3/8" 3/16" x 1" 4.2 1/2"
1 1/4" 3/8" 3/16" x 1" 4.2 1/2"
1 1/2" 5/8" 1/4" x 1 1/4" 6.8 5/8"

2" 5/8" 1/4" X 1 1/4" 6.8 5/8"
2 1/2" 5/8" 1/4" X 1 1/4" 6.8 5/8"
3" 5/8" 1/4" X 1 1/4" 6.8 5/8"

4" 3/4" 5/16" x 2" 11.1 3/4"
5" 3/4" 5/16" x 2" 11.1 3/4"

6" 7/8" 3/8" x 2 1/2" 12.7 7/8" 1" 3/8" x 2 1/2" 15.3 1"
8" 7/8" 3/8" x 2 1/2" 12.7 7/8" 1 1/8" 1/2" x 2 1/2" 21.3 1 1/4"
10" 1" 1/2" x 2 1/2" 14.2 1" 1 1/4" 1/2" x 3 1/2" 24.4 1 1/4"
12" 1" 1/2" x 2 1/2" 14.2 1" 1 3/8" 5/8" x 3 1/2" 31.1 1 1/2"
14" 1 1/4" 5/8" x 3" 19.1 1" 1 1/2" 3/4" x 4" 42.2 1 3/4"
16" 1 1/4" 5/8" x 3" 19.1 1" 1 3/4" 3/4" x 4 1/2" 44.4 1 3/4"
18" 1 1/4" 5/8" x 3" 19.1 1" 2" 1" x 4" 61.3 1 3/4"
20" 1 3/8" 3/4" x 3" 24.4 1 1/4" 2" 1" x 5" 68.0 1 3/4"
24" 1 3/8" 3/4" x 3" 20 1 1/4" 2" 1" x 6" 72.5 2"
28" 1 1/4" 3/4" x 4" 26.6 1 1/4" 2 1/4" 1" x 7" 80 2"
30" 1 3/8" 3/4" x 5" 33.3 1 1/2" 2 1/4" 1" x 8" 91.1 2 1/4"
32" 1 1/2" 3/4" x 6" 36.7 1 1/2" 2 1/2" 1 1/4" x 8" 105.6 2 1/4"
34" 1 3/4" 1" x 5" 43.6 1 1/2" 2 1/2" 1 1/2" x 7" 111.2 2 1/4"
36" 1 3/4" 1" x 5" 46.7 1 1/2" 2 3/4" 1 1/2" x 8" 124.5 2 1/2"
40" 3" WIDTH= 10" 155 2 3/4"
42" 3" WIDTH= 10" 155 2 3/4"
48" 3 1/4" WIDTH= 12" 175 3"
FOR REFERENCE NOTES, SEE DESIGN STANDARD DS-PS-120.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-120
J.M.D./T.G.
DATE
0 T.G.
03/28/95
1 SUP. H.LESKIE
DATE 03/28/95 DS-PS-122 1

TACK WELD ONE
SIDE (TYP.)
ON STOCK 8" AND WIDER, USE

"T" 2 BOLTS "E" WITH PIPE SPACERS
"W"
LOAD BOLT "D" DIA
BAR SPACER (TYP.2)

"F" WIDE x 1/2" THK
D.
O.
PIPE SPACER (TYP)
45^
TYP. "C" STOCK SIZE
(4) TOP SHEAR LUGS "G" TO

BE SUPPLIED BY SHOP OR
FIELD FABRICATOR.
(MATERIAL SAME AS PIPE)
SEE NOTE 1
TYP. 3 SIDES
10
"A" "B" "B" "A"
DOUBLE RISER PIPE CLAMP

FIG. 414A (BASED ON ANVIL INTL. FIG. 40)
FIG. 414B, 414C, 414D (BASED ON ANVIL INTL. FIG 40SD)
FOR REFERENCE DIMENSIONS & NOTES, SEE DESIGN STANDARD DS-PS-125.
NOTES:
1. FOR RUBBER LINED OR INTERNALLY COATED PIPE, LUGS TO BE SHOP WELDED PRIOR TO
RUBBER LINING OR INTERNAL COATING. ALL OTHER PIPE SHALL HAVE LUGS WELDED
AFTER PIPE INSTALLATION.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-125
J.M.D./T.G.
DATE
0 T.G.
03/28/95
ISS’D FOR CONSTRUCTION H.L. CH. Y.T. RISER CLAMP DATA
1 T.G. CLAMP FIG. No.s REVISED Y.T. SUP. DESIGN STANDARD NO. REV.
H.LESKIE
12/01/97
2 T.G.
10/22/04
"GRINNELL" CHG’D TO "ANVIL INTL."
REF. STANDARDS ADDED
DATE 03/28/95 DS-PS-123 2
TACK WELD ONE
SIDE (TYP.)
ON STOCK 8" AND WIDER, USE

"T" 2 BOLTS "E" WITH PIPE SPACERS
"W"
LOAD BOLT "D" DIA
BAR SPACER (TYP.2)

"F" WIDE x 1/2" THK
D.
O.
PIPE SPACER (TYP)
45^
TYP. "C" STOCK SIZE
(4) TOP SHEAR LUGS "G" TO

BE SUPPLIED BY SHOP OR
FIELD FABRICATOR
SEE NOTE 2
TYP. 3 SIDES
10
"B" "A"
FIG. 415A & 415B

SINGLE RISER PIPE CLAMP
(BASED ON ANVIL INTL. FIG. 41SD OR EQUAL)
FOR REFERENCE DIMENSIONS & NOTES, SEE DESIGN STANDARD DS-PS-125.
NOTES:
1. SINGLE RISER TO BE USED ONLY WHEN DOUBLE RISER CLAMP AS PER DS-PS-123
CANNOT BE USED.
2. FOR RUBBER LINED OR INTERNALLY COATED PIPE, LUGS TO BE SHOP WELDED PRIOR TO
RUBBER LINING OR INTERNAL COATING. ALL OTHER PIPE SHALL HAVE LUGS WELDED
AFTER CLAMP INSTALLATION.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-123, DS-PS-125
J.M.D./T.G.
DATE
0 T.G.
03/28/95
1 T.G. CLAMP FIG. No.s REVISED Y.T. SUP. DESIGN STANDARD NO. REV.
H.LESKIE
12/01/97
2 T.G.
10/22/04
DATE 03/28/95 DS-PS-124 2
ENGINEERING DATA FOR RISER CLAMPS
LOAD CARRYING CAPACITY IN kN. FOR RIGID HANGER RISER CLAMP APPLICATION
AT TEMPERATURE OF PIPELINE UP TO 400^C (SEE NOTE 5 BELOW)
NOM "C" "D" "E" "F" "G"

PIPE CLAMP STOCK BOLTS BOLTS SPACER SHEAR LUG SIZE ROD
DIA. FIG. No. "A" "B" SIZE (No) DIA x LGTH (No) DIA x LGTH SIZE "W" x "T" x LGTH SIZE
6 414A, 415A 13.3 2 12" 3/4 x 4 (2) 5/8 x 4 3/4 (2) 5/8 x 4 3/4 1 1 x 3/4 x 3 7/8
8 414A, 415A 13.3 2 13 1/2 3/4 x 5 (2) 5/8 x 4 3/4 (2) 5/8 x 4 3/4 1 1 1/4 x 3/4 x 3 7/8
10 414A, 415A 24.4 2 15 1x6 (2) 7/8 x 4 (2) 7/8 x 5 1 1/2 1 1/2 x 3/4 x 4 1 1/4
12 414A, 415A 34.6 2 1/2 16 1x7 (2) 1 x 5 1/2 (2) 1 x 5 1/2 1 3/4 1 1/2 x 1 1/4 x 4 1 1/2
14 414A, 415A 34.6 2 1/2 17 1x7 (2) 1 x 5 1/2 (2) 1 x 5 1/2 1 3/4 1 3/4 x 1 1/4 x 4 1 1/2
16 414A 40.0 2 1/2 18 1 1/4 x 6 (2) 1 1/8 x 6 (2) 1 1/8 x 6 2 2 x 1 1/4 x 4 1 1/2
18 414A 40.0 2 1/2 19 1/2 1 1/4 x 7 (2) 1 1/8 x 6 1/2 (2) 1 1/8 x 6 1/2 2 2 x 1 1/2 x 5 1 1/2
20 414A 60.0 3 21 1 1/2 x 8 (2) 1 3/8 x 8 (4) 1 3/8 x 8 2 1/2 2 x 1 1/4 x 6 1 3/4
24 414A 60.0 3 22 1/2 1 1/2 x 8 (2) 1 3/8 x 9 (4) 1 3/8 x 9 2 1/2 2 1/2 x 1 1/4 x 6 1 3/4
414B 49.4 2 1/2 1 1/2 x 10 (2) 1 1/4 x 8 1/4 (4) 1 x 7 3/4 2 1/4 2 1/2 x 1 3/4 x 5 1 3/4
28
30 414C 83.8 3 1/2 2 x 12 (2) 1 3/4 x 11 (4) 1 3/8 x 10 1/4 3 2 1/2 x 1 3/4 x 6 2
414D 141.6 4 1/2 2 x 16 (2) 2 1/4 x 13 (4) 1 3/4 x 12 4 2 1/2 x 2 x 9 2 1/2
414B 40.0 2 1/4 1 1/2 x 10 (2) 1 1/8 x 7 3/4 (4) 7/8 x 7 1/4 2 2 1/2 x 1 3/4 x 4 1 1/2
31
36 414C 72.2 3 2 x 12 (2) 1 1/2 x 10 (4) 1 1/8 x 9 1/4 2 1/2 2 1/2 x 1 3/4 x 6 2
414D 158.3 4 1/2 2 x 20 (2) 2 1/4 x 13 (4) 1 3/4 x 12 4 2 1/2 x 2 x 10 2 3/4
** ALL DIMENSIONS (in)
NOTES
1. LOADS ARE BASED ON USING ASTM A36 STEEL UP TO 400^C AND A387 GR. D BEYOND.
STUDS AND NUTS ARE TO ASTM A193 B7 AND A194.
2. WHEN SELECTING HANGER RODS FOR DOUBLE RISER CLAMPS & DOUBLE RISER LUGS,
USED WITH RIGID HANGERS, THE SIZE FOR A SINGLE ROD SHALL BE BASED ON THE TOTAL
LOAD AS ONLY ONE OF THE TWO RODS MAY CARRY THE TOTAL LOAD.
3. A STRICT CONTACT TOLERANCE MUST BE GUARANTEED BETWEEN SHEAR LUGS AND RISER
CLAMP SO THAT THE RISER CLAMP HAS COMPLETE CONTACT ON ALL SHEAR LUGS
SIMULTANEOUSLY UNDER ALL LOADING CONDITIONS.
4. THREADED CONNECTIONS SHALL HAVE EITHER LOCK NUTS, DOUBLE NUTS OR COTTER PINS
TO PREVENT THEM FROM VIBRATING LOOSE.
5. THE TABLE ABOVE REFLECTS THE ANVIL INTL. HANGER STD. 40 RISER CLAMP PROGRAM.
6. VERTICAL S.S. PIPE REQUIRING RISER CLAMP SUPPORTS SHALL BE REINFORCED PER DESIGN
STANDARD DS-PS-S600 UNLESS OTHERWISE SPECIFIED ON DWG.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-S600
J.M.D./T.G.
DATE
0 T.G.
03/28/95
1 T.G. CLAMP DATA REVISED Y.T. SUP. DESIGN STANDARD NO. REV.
H.LESKIE
12/01/97
2 T.G.
10/22/04
DATE 03/28/95 DS-PS-125 2
"N" "Q"
STOCK THICKNESS "C"
"P"
"D"
"M" "L"
ANVIL INTL. FIG. 432

SPECIAL PIPE CLAMP
NOM STOCK APPROX.

PIPE "D" THICKNESS WEIGHT
DIA. "C" "L" "M" "N" "P" "Q" IN LBS.
Note 1 Note 2 Note 2
2 1/2" 5/16" 1/8" 6" 5 1/4" 4 1/4" 1/4" 4 1/2" 3

3" 5/16" 1/8" 6" 5 7/8" 5" 1/4" 4 1/2" 3
3 1/2" 5/16" 1/8" 6" 6 3/8" 5 1/2" 1/4" 4 1/2" 4
4" 5/16" 1/8" 6" 6 15/16" 6 1/16" 1/4" 4 1/2" 4
5" 5/16" 1/8" 6" 8" 7" 1/4" 4 1/2" 5
6" 3/8" 3/16" 9" 9 1/2" 8 3/8" 3/8" 6" 12
8" 3/8" 3/16" 9" 11 1/2" 10 3/8" 3/8" 6" 15

10" 3/8" 3/16" 9" 13 5/8" 12 1/2" 1/2" 6" 18
12" 3/8" 3/16" 9" 15 11/16" 14 9/16" 1/2" 6" 21
14" 1/2" 1/4" 12" 17 7/16" 16 1/16" 1/2" 8" 41

16" 1/2" 1/4" 12" 19 7/16" 18 1/16" 1/2" 8" 46
18" 1/2" 1/4" 12" 21 7/16" 20 1/16" 1/2" 8" 52
20" 1/2" 1/4" 12" 23 7/16" 22 1/16" 5/8" 8" 57
24" 1/2" 1/4" 12" 27 1/2" 26 1/4" 5/8" 8" 67
FOR REFERENCED NOTES SEE DESIGN STANDARD DS-PS-120.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-120
J.M.D./T.G.
DATE
0 T.G.
03/28/95
1 SUP. H.LESKIE
DATE 03/28/95 DS-PS-126 1

REINFORCING PAD PER
OR "H" AS SPEC.
DESIGN STANDARD
DS-PS-S600 FOR
ON DRAWING
THIN WALL ONLY
IF SPECIFIED ON DRAWING.
CARBON STEEL
OR THIN WALL
PIPE
100 WITH
12
5 REPAD
TYP
38x25
WITHOUT
5 INSULATION
REPAD
13 BAND SLOT
TYP.
TYP
6 50mm FOR ANCHORING TO
SEE NOTES
CONCRETE, OR BOLT GAUGE
4 AND 7 455 TO SUIT SUPPORT STEEL
FOR BOLTED ATTACHMENT,

12
USE (4) 5/8 " DIA. A325 BOLTS
5 C/W NUTS & LOCK WASHERS
IF ANCHORED TO STEEL OR
(4) 5/8 " DIA. x 5" LONG HILTI
HIT HY 150 ADHESIVE ANCHORS
IF ANCHORED TO CONCRETE
25 25
SEE NOTE 5.
150
NOTES:
1. THIS ANCHOR IS APPLICABLE TO LINES 3" TO 10" ONLY.
2. STAMP SHOE ASSEMBLY TAG NO. IN 6mm HIGH LETTERS IN THE CENTER OF SHOE
13mm FROM TOP EDGE OF PLATE.
3. SIZE BOLT HOLES IN BASE PLATE TO SUIT CONNECTION BOLT OR ANCHORS.
4. SUPPORT STEEL OR CONCRETE MUST BE REVIEWED BY THE STRUCTURAL ENGINEER.

5. FOR BOLTED ATTACHMENT MAXIMUM AXIAL LOAD 11.1 kN, MAXIMUM LATERAL LOAD 3.1 kN.
6. THIS ANCHOR IS NOT SUITABLE FOR RUBBER LINED OR INTERNALLY COATED PIPE.
USE DESIGN STANDARD DS-PS-A203 INSTEAD.
7. WELD TO STEEL MEMBERS OR FIELD DRILL BASEPLATE TO SUIT CONCRETE
ANCHOR DETAIL.
SUPPORT SUPPORT
TAG MATERIAL
200B BOLTED/C.S.
200W WELDED/C.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-600
J.M.D./T.G.
DATE
0 T.G. ISS’D FOR CONSTRUCTION H.L. CH. Y.T. ANCHOR

03/28/95

SUP. H.LESKIE
10/22/04 KWIK-BOLTS CHANGED TO HILTI HIT
2 D.K.
11/18/05
ADDED WELDED OPTION B.C. DATE 03/28/95 DS-PS-A200 2
*DATE*TIME* CADD FILE No. PSP108\CAD\250\PIPE SUPPORT STANDARDS\DSPSA200.DGN
REINFORCING PAD PER
DESIGN STANDARD
OR "H" AS SPEC.
DS-PS-S600 FOR
THIN WALL ONLY
ON DRAWING
CARBON STEEL IF SPECIFIED ON DRAWING.
OR THIN WALL
PIPE
100
WITH
12
6 REPAD
TYP
38x25
WITHOUT 6
INSULATION
REPAD
13 BAND SLOT
TYP.
TYP
125mm FOR ANCHORING TO
6 455
SEE NOTES
4 AND 7
TO SUIT SUPPORT STEEL
12
TYP TYP FOR BOLTED CONNECTION,

6 USE (4) 5/8 " DIA. A325
BOLTS C/W NUTS & LOCK WASHERS
165 HIT HY 150 ADHESIVE ANCHORS
( SEE NOTE 5 )
25 25
305
NOTES:
3. SIZE BOLT HOLES IN BASE PLATE TO SUIT CONNECTION BOLTS OR ANCHORS.
5. FOR BOLTED CONNECTION MAXIMUM AXIAL LOAD 22.2 kN, MAXIMUM LATERAL LOAD 11.1 kN.
USE DESIGN STANDARD DS-PS-A204.
7. WELD TO STEEL MEMBER OR FIELD DRILL BASEPLATE TO SUIT CONCRETE ANCHOR DETAIL.
SUPPORT SUPPORT
TAG MATERIAL
201B BOLTED/C.S.
201W WELDED/C.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-600
J.M.D./T.G.
DATE
0 T.G. ISS’D FOR CONSTRUCTION H.L. CH. Y.T. ANCHOR

03/28/95
1 T.G. REF. STANDARDS ADDED Y.T. DESIGN STANDARD NO. REV.

SUP. H.LESKIE
20/10/04 HILTI ANCHOR TYPE CHG’D
2 D.K.
11/18/05
OR "H" AS SPEC.
ON DRAWING
CARBON STEEL
OR THIN WALL
PIPE
38x25 INSULATION
BAND SLOT
B.O.P.
100
TYP
7 150
12
150 150
455
TYP
7 150
REINFORCING PAD PER FOR CONNECTION INFO

DESIGN STANDARD SEE NOTES 3 & 4.
DS-PS-S600
TYP
5 100-165
90
PIPE
"A"
DIA.
20" 305
TYP 24" 380

5
28" 455
"A"
TYP.
12
30" 510
32" 560
36" 610
90
13
TYP.
NOTES:
3. SUPPORT STEEL OR CONCRETE MUST BE REVIEWED BY THE STRUCTURAL ENGINEER
4. WELD TO STEEL MEMBERS OR FIELD DRILL BASEPLATE TO SUIT CONCRETE ANCHOR DETAIL.
USE DESIGN STANDARD DS-PS-A205 INSTEAD.
SUPPORT SUPPORT
TAG MATERIAL
202 C.S.
202S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-S600
J.M.D./T.G.
DATE
0 T.G.
03/28/95
ISS’D FOR CONSTRUCTION H.L. CH. Y.T. ANCHOR
1 T.G. REF. STANDARDS ADDED SUP. DESIGN STANDARD NO. REV.
H.LESKIE
10/22/04
2 D.K.
11/23/05
MODIFIED REPAD DETAIL B.C. DATE 03/28/95 DS-PS-A202 2
OR "H" AS SPEC.
PIPE
"W" "T" "W"
DIA.
ON DRAWING
3"-4" 10 50
"T"
NON-THIN WALL
S.S, ALLOY OR 6"-10" 12 75
RUBBER LINED C.S. PIPE
B.O.P. SEE
NOTE 8
100
5
TYP.
12 5
38x25
INSULATION
BAND SLOT
TYP. 13
6
SEE NOTES TYP.
5 AND 9
MIN. 455 CONCRETE, OR BOLT GAUGE
OR "L" AS SPEC. ON DRAWING TO SUIT SUPPORT STEEL
(SEE NOTE 7)
25 TYP.
(4) SHEAR LUGS PIPE CLAMP

MATERIAL SAME AS PIPE ANVIL INTL. FIG. 212
( SEE NOTE 3 ) OR EQUAL
FOR BOLTED CONNECTION,

12
USE (4) 5/8 " DIA. A325 BOLTS
C/W NUTS & LOCK WASHERS
5
(SEE NOTE 6 & 7.)
25 25
150
NOTES:
3. ONE OF THE PIPE CLAMPS SHALL BE FITTED WITH SHEAR LUGS.
4. SIZE BOLT HOLES IN BASE PLATE TO SUIT CONNECTION BOLTS OR ANCHORS. SEE NOTE 7.
5. SUPPORT STEEL OR CONCRETE MUST BE REVIEWED BY STRUCTURAL ENGINEER.
6. FOR BOLTED CONNECTION MAXIMUM AXIAL LOAD 11.1 kN, MAXIMUM LATERAL LOAD 3.1 kN,
FOR GREATER LOADS CONSULT STRUCTURAL ENGINEER.
SUPPORT SUPPORT
TAG MATERIAL
203B BOLTED/C.S.
203W WELDED/C.S.
7. BOLTS AND ASSOCIATED HARDWARE NOT APPLICABLE WHEN

USED IN CONJUCTION WITH DESIGN STANDARDS DS-PS-DA250 & DS-PS-DA252.
8. RUBBER LINED OR INTERNALLY COATED PIPE SHALL HAVE LUGS SHOP WELDED PRIOR TO
RUBBER LINING OR INTERNAL COATING. ALL OTHER PIPE SHALL HAVE LUGS FIELD WELDED.
9. WELD TO STEEL MEMBER OR FIELD DRILL BASEPLATE TO SUIT CONCRETE ANCHOR DETAIL.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS

J.M.D./T.G.
DATE
0 T.G.
03/28/95
"GRINNELL" CHG’D TO "ANVIL INTL." DESIGN STANDARD NO. REV.
2 T.G. SUP.
KWIK-BOLTS CHG’D TO HILTI HIT H.LESKIE
10/22/04
3 D.K.
11/18/05
100 SEE
NOTE 8
TYP.
7
OR "H" AS SPEC.
NON-THIN WALL
ON DRAWING
12
S.S, ALLOY OR
RUBBER LINED C.S. PIPE
B.O.P.
100
TYP.
7
12
38x25
INSULATION
TYP. 13 BAND SLOT
6
SEE NOTES TYP.
5 AND 9 125mm FOR ANCHORING TO
MIN. 455
OR "L" AS SPEC. ON DRAWING
25 TYP. (SEE NOTE 7)
(7) SHEAR LUGS

MATERIAL SAME AS PIPE
PIPE CLAMP
(SEE NOTE 3)
OR EQUAL
FOR BOLTED CONNECTION,

12
USE (4) 5/8 " DIA. A325
TYP TYP
7 BOLTS C/W NUTS & LOCK WASHERS
165
( SEE NOTE 6 & 7)
25 25
305
NOTES:
4. SIZE BOLT HOLES IN BASE PLATE TO SUIT CONNECTION BOLTS OR ANCHORS. SEE NOTE 7.
6. FOR BOLTED CONNECTION MAXIMUM AXIAL LOAD 22.2 kN, MAXIMUM LATERAL LOAD 11.1 kN,
FOR GREATER LOADS CONSULT STRUCTURAL ENGINEER.
7. BOLTS AND ASSOCIATED HARDWARE NOT APPLICABLE WHEN

USED IN CONJUCTION WITH DESIGN STANDARD DS-PS-DA251. SUPPORT SUPPORT
TAG MATERIAL
8. RUBBER LINED OR INTERNALLY COATED PIPE SHALL HAVE LUGS
SHOP WELDED PRIOR TO RUBBER LINING OR INTERNAL COATING.
204B BOLTED/C.S.
ALL OTHER PIPE SHALL HAVE LUGS FIELD WELDED.
9. WELD TO STEEL MEMBER OR FIELD DRILL BASEPLATE TO SUIT 204W WELDED/C.S.

CONCRETE ANCHOR DETAIL.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS

J.M.D./T.G.
DATE
0 T.G.
03/28/95
2 T.G. "GRINNELL" CHG’D TO "ANVIL INTL." DESIGN STANDARD NO. REV.
SUP. H.LESKIE
3 D.K.
11/18/05
*DATE*TIME* CADD FILE No. PSP108\CAD\PIPE SUPPORT STANDARDS\DSPSA204.DGN
PIPE CLAMP ANVIL INTL. OR EQUAL.
SEE TABLE FOR FIG. No.
SEE NOTE 6
SEE (7) SHEAR LUGS
"B" 100 TYP.
NOTE 7 MATERIAL SAME
TYP
AS PIPE ( SEE NOTE 3 )
7
38
NON-THIN WALL TYP.
TYP.
S.S., ALLOY, OR
OR "H" AS SPEC.
20
RUBBER LINED
ON DRAWING
C.S. PIPE
B.O.P.
12
100
38x25 TYP
INSULATION 7
BAND SLOT
150 150 FOR CONNECTION

INFO SEE NOTES 4 & 5
MIN. 455
OR "L" AS SPEC. ON DWG.
TYP
5 100-165
PIPE ANVIL INTL.

90
"A" "B"
DIA. CLAMP
SEE NOTE 6
20" 305 455 FIG. 212/212S
24" 380 455 FIG. 212/212S
TYP
5 28" 455 660 FIG. 216/216S
"A"
TYP.
30" 510 660 FIG. 216/216S

12
32" 560 660 FIG. 216/216S
36" 610 660 FIG. 216/216S

90
13
TYP.
NOTES:
5. WELD TO STEEL MEMBERS OR FIELD DRILL BASEPLATE TO SUIT CONCRETE ANCHOR DETAIL
EXCEPT WHEN USED IN CONJUCTION WITH DESIGN STANDARD DS-PS-DA251.
6. FOR BASE LENGTH EQUAL TO 455 mm, USE "B" AS SHOWN IN TABLE.
OTHERWISE, "B" = "L" (AS SPECIFIED ON DWG.) + CLAMP WIDTH (PER DS-PS-121)
7. RUBBER LINED OR INTERNALLY COATED PIPE SHALL HAVE LUGS SHOP WELDED PRIOR TO
RUBBER LINING OR INTERNAL COATING. ALL OTHER PIPE SHALL HAVE LUGS FIELD WELDED.
SUPPORT SUPPORT
TAG MATERIAL
205 C.S.
205S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS

J.M.D./T.G.
DATE
0 T.G.
03/28/95
1 C.M. PLASTIC PIPE OPTION REMOVED H.L. SUP. DESIGN STANDARD NO. REV.
H.LESKIE
03/18/96
2 T.G.
10/22/04
"GRINNELL" CHG’D TO "ANVIL INTL." DATE 03/28/95 DS-PS-A205 2
(2) U-BOLTS ANVIL INTL. FIG. No. 137 OR EQUAL
C/W (4) FINISHED HEX NUTS EA.
PIPE
"T" "W"
DIA.
3"-4" 10 50
2 REINFORCING PADS FOR THIN
6"-10" 12 75
WALL AND PLASTIC PIPE ONLY,
PER DESIGN STANDARD DS-PS-S600
W IF SPECIFIED ON DRAWING.
TYP.
25
(2) SHEAR LUGS FOR

METAL PIPE ONLY,
MATERIAL SAME AS PIPE,
( SEE NOTE 2 )
PIPE ROD MAX. LATERAL

SIZE SIZE LOAD (kN)
1/2" - 1" 1/4" 0.6
1 1/4" - 2" 3/8" 1.6
2 1/2" - 4" 1/2" 3.0
6" - 8" 5/8" 4.8
10" 3/4" 7.1

SEE
NOTE 2 12" 7/8" 10.0
"T" 5
NOTES:
1. THIS SUPPORT IS APPLICABLE TO LINES 12" AND SMALLER ONLY.
2. FOR RUBBER LINED OR INTERNALLY COATED PIPE, SHEAR LUGS SHALL BE SHOP WELDED
TO BOTTOM OF PIPE OR WEAR PAD PRIOR TO RUBBER LINING OR INTERNAL COATING.
NON RUBBER LINED OR NON COATED METAL PIPES SHALL BE FIELD WELDED.
3. SUPPORT STEEL MUST BE REVIEWED BY THE STRUCTURAL ENGINEER.
SUPPORT SUPPORT
TAG MATERIAL
209 C.S.
209S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-S600, DS-PS-S601
J.M.D./T.G.
DATE
0 T.G.
03/28/95
SUP. H.LESKIE
10/22/04 "GRINNELL" CHG’D TO "ANVIL INTL."
2 D.K.
11/23/05
REPAD DETAIL MODIFIED B.C. DATE 03/28/95 DS-PS-A209 2
(8) SHEAR LUGS TO BE
WELDED TO PIPE AFTER
CLAMP INSTALLATION
"A"
"
"T
SUPPORT FIG. 609 OR 609S
"W
SEE DESIGN STANDARD
"
DS-PS-S609
SPECIFIED ON DRAWING
STD. WT. PIPE

"L"
6
"C"
6mm dia. VENT HOLE
BASE PLATE PER DESIGN

6
STANDARD DS-PS-X756
IF SPECIFIED ON DRAWING
GROUT
CONCRETE PEDESTAL
WHERE APPLICABLE
PIPE "L" SHEAR LUG SIZE BASE PLATE MAX LAT.

"C"
DIA. MAX. "W" x "T" x "A" SIZE LOAD (kN)
3" - 4" 2" 610 20x20x50 TYPE 1 3.1
6" 3" 910 25x20x75 " 4.0
8" 4" 910 32x20x75 " 4.9
10" - 12" 4" 910 38x20x75 TYPE 2 9.3
14" 6" 910 45x20x75 " 12.2
16" 6" 910 50x35x100 " 12.2
18" 6" 910 50x35x100 " 12.2
NOTES:
SUPPORT SUPPORT
TAG MATERIAL
210 C.S.
210S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-S609, DS-PS-X756
J.M.D./T.G.
DATE
0 T.G.
03/28/95
H.LESKIE
10/22/04
DATE 03/28/95 DS-PS-A210 1

REINFORCING PAD PER
DESIGN STANDARD
DS-PS-S600 OR DS-PS-S602
FOR S.S. OR ALLOY PIPE ONLY
SEE
NOTE 2
ON DRAWING
SPECIFIED
7
STD. WT. PIPE
"L"
"C"
6mm dia. VENT HOLE

STANDARD DS-PS-X756
7
GROUT
CONCRETE PEDESTAL
WHERE APPLICABLE
MAX. LATERAL
PIPE "L"
"C" LOAD BASE PLATE
SIZE MAX.
(kN)
2" & DN SAME AS PIPE 610 3.1
3" 3" 610 4.0 TYPE 1
4" - 6" 4" 910 4.9
8" - 10" 6" 910 11.1 TYPE 2
NOTES:
2. FOR RUBBER LINED OR INTERNALLY COATED PIPE, ALL WELDING SHALL BE PERFORMED
PRIOR TO RUBBER LINING AND INTERNAL COATING.
SUPPORT SUPPORT
TAG MATERIAL
211 C.S.
211S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-S600, DS-PS-S602, DS-PS-X756
J.M.D./T.G.
DATE
0 T.G.
03/28/95
H.LESKIE
10/22/04
2 D.K.
11/23/05
REPAD DETAIL MODIFIED B.C. DATE 03/28/95 DS-PS-A211 2
METAL
PIPE
ANGLE "A"
TYP
"T"
100 MIN.
STEEL WIDTH
REINFORCING PAD PER

DESIGN STANDARD
DS-PS-S600 IF
PIPE WELD
ANGLE SIZE "A"
DIA. "T"
2"-4" L25x25x4.8x150mm LG. 5
6"-8" L38x38x6.4x150mm LG. 5
10"-12" L51x51x6.4x200mm LG. 7
14"-16" L76x76x9.5x200mm LG. 7
18"-20" L102x102x9.5x255mm LG. 7
22"-26" L127x127x9.5x255mm LG. 9
28"-32" L152x152x9.5x255mm LG. 9
NOTES:
1. THIS ANCHOR IS APPLICABLE TO UNINSULATED LINES 2" TO 32" ONLY.
SUPPORT SUPPORT
TAG MATERIAL
212 C.S.
212S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-S600
J.M.D./T.G.
DATE
0 T.G.
03/28/95
H.LESKIE
10/22/04
DATE 03/28/95 DS-PS-A212 1

BUTT WELD & GRIND
TYP. INTERNAL SURFACE SMOOTH
5
PLASTIC PIPE CLAMPS (2)

PIPE ANVIL INTL. FIG.432
OR EQUAL
SEE NOTE 3
120^
3x510
12mm PLATE RUBBER PAD
SEE NOTES 4 & 5
BOTH SIDES
MIN.
TYP.
13
10
TYP.
6mm PLATE 5
12mm PLATE
100 0
TYP. TYP.
BUTT WELD & GRIND

5

OR EQUAL
SEE NOTE 3
120^
3x510
150 MAX
RUBBER PAD
SEE NOTES 4 & 5
12mm PLATE TYP.

BOTH SIDES 10
6mm PLATE
MIN.
TYP.
6
5
12mm PLATE
100 305 0
TYP. MAX. TYP.
NOTES
1. THIS ANCHOR IS APPLICABLE TO LINES 6" TO 12" SUPPORTED ON STEEL OR ON CONCRETE

PIERS OR SLEEPERS WITH EMBEDDED PLATES.
2. CONCRETE OR STEEL SUPPORT MUST BE REVIEWED BY THE STRUCTURAL ENGINEER.
3. DESIGNER TO REFER TO STANDARD DS-PS-126 FOR CLAMP DIMENSIONS.
4. CLAMP RUBBER PAD AND PIPE TIGHT.

5. WHERE CLAMP OVERLAPS BUTT FUSION WELD BEAD, EXTERNAL BEAD IS TO BE REMOVED
PER MANUFACTURERS INSTRUCTIONS.
SUPPORT SUPPORT
TAG MATERIAL
A214 C.S.
A214S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-126
J.M.D./T.G.
DATE
0 T.G.
03/28/95
T.G. REF. STANDARDS ADDED DESIGN STANDARD NO. REV.
1 SUP. H.LESKIE
DATE 03/28/95 DS-PS-A214 1

BUTT WELD & GRIND
INTERNAL SURFACE SMOOTH
TYP. TYP.
10
5 PIPE CLAMPS (2)
PLASTIC ANVIL INTL. FIG.432
PIPE OR EQUAL
SEE NOTE 3
120^
TYP.
200
3x660
RUBBER PAD
SEE NOTES 4 & 5
HP 200x53
MIN.
13
16mm PLATE TYP.
BOTH SIDES 7
16mm PLATE
150 0
TYP. TYP.
BUTT WELD & GRIND

5

OR EQUAL
SEE NOTE 3
120^
3x660
RUBBER PAD
MAX.
200
SEE NOTES 4 & 5
TYP.
10
12
MIN.
HP 200 x 53
6
16mm PLATE 16mm PLATE TYP.
BOTH SIDES 7
150 305 0
TYP. (MAX.) TYP.
NOTES
1. THIS ANCHOR IS APPLICABLE TO LINES 14" TO 24" SUPPORTED ON STEEL OR ON CONCRETE
PIERS OR SLEEPERS WITH EMBEDDED PLATES.

2. CONCRETE OR STEEL SUPPORT MUST BE REVIEWED BY THE STRUCTURAL ENGINEER.
SUPPORT SUPPORT
TAG MATERIAL
A215 C.S.
A215S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-126
J.M.D./T.G.
DATE
0 T.G.
03/28/95
1 SUP. H.LESKIE
DATE 03/28/95 DS-PS-A215 1

3mm THK. RUBBER BUTTWELD & GRIND
PAD AROUND PLASTIC INTERNAL SURFACE SMOOTH
OR "H" AS SPEC.
PIPE
( SEE NOTE 3 )
ON DRAWING
PLASTIC PIPE
100
12
TYP.
12
TYP.
5
38x25
12mm PLATE INSULATION
BAND SLOT
12
TYP.

3" dia. & 4" dia. = 255mm CONCRETE, OR BOLT GAUGE
6" dia. - 12" dia. = 405mm TO SUIT SUPPORT STEEL
(2) PIPE CLAMPS

OR EQUAL
SEE NOTE 7
12
USE (4) 5/8" DIA. A325 BOLTS
5
(4) 5/8" DIA. x 5"
KWIK-BOLTS IF
ANCHORED TO CONCRETE
SEE NOTE 6
25 25
150
NOTES:
4. SIZE BOLT HOLES IN BASE PLATE TO SUIT CONNECTION
BOLTS OR ANCHORS.
5. SUPPORT STEEL OR CONCRETE MUST BE REVIEWED
BY STRUCTURAL ENGINEER
6. THESE ATTACHMENTS ARE FOR MAXIMUM AXIAL LOAD 11.1 kN, MAXIMUM LATERAL
LOAD 3.1 kN. FOR GREATER LOADS CONSULT STRUCTURAL ENGINEER.
SUPPORT SUPPORT
TAG MATERIAL
216 C.S.
216S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-126
J.M.D./T.G.
DATE
0 T.G.
03/28/95
1 SUP. H.LESKIE
DATE 03/28/95 DS-PS-A216 1

BUTTWELD &
GRIND INTERNAL
SURFACE SMOOTH
OR "H" AS SPEC.
PLASTIC PIPE
ON DRAWING
7
100
TYP.
7
12
12mm PLATE (TYP.)
3x660 RUBBER 38x25

PAD AROUND INSULATION
PLASTIC PIPE BAND SLOT
(SEE NOTES 3 & 8)
12
TYP.
455 125mm FOR ANCHORING TO
(2) PIPE CLAMPS

OR EQUAL
SEE NOTE 7
12
USE (4) 5/8" DIA. A325
TYP TYP
7 BOLTS C/W NUTS & LOCK WASHERS
(4) HILTI HVA M20 x 240 (3/4" dia. )
SEE NOTE 6
165
25 25
305
NOTES:
4. SIZE BOLT HOLES IN BASE PLATE TO SUIT CONNECTION BOLTS OR ANCHORS.
6. THESE ATTACHMENTS ARE FOR MAXIMUM AXIAL LOAD 22.2 kN, MAXIMUM LATERAL
LOAD 11.1 kN. FOR GREATER LOADS CONSULT STRUCTURAL ENGINEER.
SUPPORT SUPPORT
TAG MATERIAL
217 C.S.
217S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-126
J.M.D./T.G.
DATE
0 T.G.
03/28/95
1 SUP. H.LESKIE
DATE 03/28/95 DS-PS-A217 1

PIPE CLAMPS (2) ANVIL INTL.
3x660 RUBBER PAD
FIG. 432 OR EQUAL.
SEE NOTES 6 & 7
SEE NOTE 3
610 BUTTWELD & GRIND
INTERNAL SURFACE
SMOOTH
38
TYP.
TYP.
OR "H" AS SPEC.
20
ON DRAWING
PLASTIC PIPE
12
100
12mm PLATE
(TYP.)
7
38x25 TYP
INSULATION 7
BAND SLOT
150 150 FOR CONNECTION

INFO SEE NOTES 5
455
5
TYP
5 100-230
PIPE
90
"A"
DIA.
20" 305
24" 380
5
SEE TABLE
TYP
5
"A"
TYP.
12
90
12
TYP.
NOTES:
5. WELD TO STEEL MEMBERS OR FIELD DRILL BASEPLATE TO SUIT CONCRETE ANCHOR DETAIL.
SUPPORT SUPPORT
TAG MATERIAL
218 C.S.
218S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-126
J.M.D./T.G.
DATE
0 T.G.
03/28/95
1 SUP. H.LESKIE
DATE 03/28/95 DS-PS-A218 1

METAL PIPE
REINFORCING PAD
PER DESIGN STANDARD
DS-PS-S600 IF
MIN.
13
TYP.
7
WT100x23 (8" TO 10" LINES)
GAP "G" = 1.6mm (TYP.) WT75x11 (3" TO 6" LINES)
OR AS SPECIFIED
ON DRAWING.
METAL OR
PLASTIC
PIPE
PIPE SHOE PER DESIGN

STANDARD DS-PS-S603
OR DS-PS-A203 AS
MIN.
13
TYP.
7
WT100x23 (8" TO 10" LINES)
GAP "G" = 1.6mm (TYP.) WT75x11 (3" TO 6" LINES)
OR AS SPECIFIED
ON DRAWING.
NOTES
1. THIS DIRECTIONAL ANCHOR IS APPLICABLE TO LINES 3" TO 10" SUPPORTED ON STEEL ONLY.
SUPPORT SUPPORT
TAG MATERIAL
250 C.S.
250S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-S603, DS-PS-A203
J.M.D./T.G.
DATE
0 T.G.
03/28/95
ISS’D FOR CONSTRUCTION H.L. CH. Y.T. DIRECTIONAL ANCHOR
1 T.G. WT SIZES & GAP REVISED Y.T. SUP. DESIGN STANDARD NO. REV.
H.LESKIE
10/22/04
2 T.G.
10/22/04
REF. STANDARDS ADDED DATE 03/28/95 DS-PS-DA250 2
*DATE*TIME* CADD FILE No. PSP108\CAD\250\PIPE SUPPORT STANDARDS\DSPSDA250.DGN
METAL
PIPE
REINFORCING PAD
PER DESIGN STANDARD
DS-PS-S600 IF
MIN.
13
150 HP200x54
TYP. 230
TYP.
12mm PLATE 7
GAP "G" = 1.6mm (TYP.) TYP.

OR AS SPECIFIED 7
ON DRAWING.
METAL OR
PLASTIC
PIPE

STANDARD DS-PS-S604/S605
OR DS-PS-A204/A205 AS
MIN.
13
HP200x54 230
TYP.
150 12mm PLATE 7
TYP. TYP.
GAP "G" = 1.6mm (TYP.)
7
OR AS SPECIFIED
ON DRAWING.
NOTES
1. THIS DIRECTIONAL ANCHOR IS APPLICABLE TO LINES 12" TO 36"

SUPPORTED ON STEEL ONLY.
SUPPORT SUPPORT
TAG MATERIAL
251 C.S.
251S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-S600, DS-PS-S604/S605, DS-PS-A204/A205
J.M.D./T.G.
DATE
0 T.G.
03/28/95
1 T.G. LENGTH ADDED FOR HP8 Y.T. SUP. DESIGN STANDARD NO. REV.
H.LESKIE
10/22/04
2 T.G.
10/22/04
METAL PIPE
150 MAX.
REINFORCING PAD
PER DESIGN STANDARD
DS-PS-S600 IF
MIN.
6
WT100x23 (8" & 10" LINES)
WT75x11 (3" TO 6" LINES)
GAP "G" = 1.6mm (TYP.)

TYP.
OR AS SPECIFIED
7
ON DRAWING.
METAL OR
PLASTIC
PIPE
150 MAX.
STANDARD DS-PS-S603
OR DS-PS-A203 AS
MIN.
6
WT100x23 (8" & 10" LINES)
WT75x11 (3" TO 6" LINES)
GAP "G" = 1.6mm (TYP.) TYP.

OR AS SPECIFIED 7
ON DRAWING.
NOTES
1. THIS DIRECTIONAL ANCHOR IS APPLICABLE TO LINES 3" TO 10" SUPPORTED ON CONCRETE

PIERS, WALLS OR SLEEPERS ONLY.
2. CONCRETE SUPPORT MUST BE REVIEWED BY THE STRUCTURAL ENGINEER.
SUPPORT SUPPORT
TAG MATERIAL
252 C.S.
252S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-S600, DS-PS-S603, DS-PS-A203
J.M.D./T.G.
DATE
0 T.G.
03/28/95
1 T.G. WT SIZES & GAP REVISED Y.T. SUP. DESIGN STANDARD NO. REV.
H.LESKIE
10/22/04
2 T.G.
10/22/04
PIPE SUPPORT AS
SPECIFIED ON
DRAWING
C.S. PLATE
12x22x150 LG
ASTM A36
WT75x15, 50mm LG
C.S. ASTM A36
12
7
5
1.6
TYP.
NOTES:
2. THIS GUIDE CAN BE APPLIED TO THE FOLLOWING SUPPORT STANDARDS:
- DS-PS-S603 - DS-PS-S606
SUPPORT SUPPORT
TAG MATERIAL
300 C.S.
300S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-S603/S604/S605, DS-PS-606/S607/S608
J.M.D./T.G.
DATE
0 T.G.
03/28/95
ISS’D FOR CONSTRUCTION H.L. CH. Y.T. GUIDE
H.LESKIE
10/22/04
DATE 03/28/95 DS-PS-G300 1

*DATE*TIME* CADD FILE No. PSP108\CAD\250\PIPE SUPPORT STANDARDS\DSPSG300.DGN
U-BOLT ANVIL INTL.
FIG. 137 OR EQUAL
3mm GAP ALL AROUND
"
"D
REINFORCING PAD
PER DESIGN STANDARD
DS-PS-S600
FOR THIN WALL ONLY
NOM. ALTERNATE
ROD SIZE
PIPE
"B"
DIA. "D"
1/2" 3/8"
3/4" 3/8"
1" 3/8"
1 1/4" 3/8"
1 1/2" 3/8"
2" 3/8"
2 1/2" 1/2"
3" 1/2"
4" 1/2"
5" 1/2"
6" 5/8"
8" 5/8"
10" 3/4"
12" 7/8"
14" 7/8"
16" 7/8"
18" 1" DO NOT USE
20" 1" WITHOUT PERMISSION
OF STRESS ENGINEER
22" 1"
24" 1"
NOTES:
1. U-BOLTS SHOULD NOT BE CLAMPED TIGHT AT THE PIPE.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-S600
J.M.D./T.G.
DATE
0 T.G.
03/28/95
2 SUP. H.LESKIE
3 D.K.
11/18/05
ADDED ADDITIONAL SIZE B.C. DATE 03/28/95 DS-PS-G302 3
REINFORCING PADS 305mm dia.
OR 255mm SQUARE FOR
CONNECTION TO TANK WALL
MATERIAL & THICKNESS
TO MATCH TANK TANK SUPPORT STEEL
"T" 50-125
TYP.
"W" 30^ 30^
1830 MAX.
3mm dia. VENT

HOLE (TYP.)
STD. WT. PIPE

TYP. DIA. "D"
"W"
LOOSE FIT TO PERMIT
PIPE SPACER PIPE MOVEMENT
PIPE CLAMP ANVIL INTL.
"T"= TANK WALL THK. FIG. 212 OR EQUAL

SEE NOTE 2
"W"= PIPE "D"

WALL THK.
REINFORCING PADS
PER DESIGN STANDARD
NOMINAL PIPE
DS-PS-S615 FOR
PIPE SIZE "D"
PLASTIC PIPE ONLY
2 1/2" 1"
3" 1"
4" 1"
6" 1 1/2"
8" 2"
10" 3"
12" 3"
14" 4"
16" 4"
18" 4"
20" 4"
24" 4"
NOTES
1. SPECIFY C
ELEVATION OF SWAY BRACE ON SUPPORT DWG.
2. (2) PIPE CLAMPS ANVIL INTL. FIG. 212 OR EQUAL SHALL BE WELDED TOGETHER
(INTERMITTENT WELD) TO SUIT PIPE "D" FOR NOMINAL PIPE SIZE 8" & ABOVE.
SUPPORT SUPPORT
TAG MATERIAL
303 C.S.
303S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-S603/S604/S605, DS-PS-S606/S607/S608
J.M.D./T.G.
DATE
0 T.G.
03/28/95
1 SUP. H.LESKIE
DATE 03/28/95 DS-PS-G303 1

1.6
50
AS SHOWN
ON DWG.
"L"
REINFORCING PAD PER
SUPPORT SHOE IF SPECIFIED ON DWG.
DESIGN STANDARD DS-PS-600
TEE SHAPE
"T" WELDED ’W’
SHAPE
(SEE NOTE 2.) 5
STANDARD ALTERNATE
TEE
PIPE
SHAPE
SIZE
"T"
10" & DN WT75x15
12" - 24" WT100x23
26" - 36" WT155x37
NOTES:
2. WHERE SPACE BETWEEN ADJACENT PIPES, OR WIDTH OF SUPPORT STEEL

DOES NOT ALLOW FOR ADEQUATE WELDING OF 2 STAGGERED GUIDE TEES,
THE AFFECTED TEES SHALL BE REPLACED BY A FABRICATED ’W’ SECTION OF
EQUIVALENT FLANGE WIDTH AND THICKNESS.
SUPPORT SUPPORT
TAG MATERIAL
306 C.S.
306S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-S600
J.M.D./T.G.
DATE
0 T.G.
03/28/95
H.LESKIE
10/22/04
4 D.K.
11/18/05
HEIGHT DIM. ADDED B.C. DATE 03/28/95 DS-PS-G306 4
HANGER DATA
WELD LENGTH AND SIZE FOR CORRESPONDING ROD DIAMETERS

FOR UPPER HANGER ASSEMBLY.
HANGER LENGTH SIZE OF
ROD OF WELD FILLET "W"
DIA. "L" MIN. MAX.
3/8 20 3 7
1/2 20 3 7
5/8 20 5 7
3/4 20 7 10
7/8 32 7 10
1 32 10 13
1 1/8 32 10 13
1 1/4 32 13 16
1 1/2 38 16 20
1 3/4 57 16 20
2 57 20 20
2 1/4 70 20 20
2 1/2 83 20 20
2 3/4 155 16 20
3 155 16 20
3 1/4 178 20 25
3 1/2 178 20 25
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
Pe
J.M.D./T.G.
DATE
0 T.G.
03/28/95
ISS’D FOR CONSTRUCTION H.L. CH. Y.T. HANGER ASSEMBLY NOTES
1 J.H. RODS & NUTS ADDED Y.T. SUP. DESIGN STANDARD NO. REV.
H.LESKIE
12/01/97
2 T.G.
10/22/04
DATE 03/28/95 DS-PS-H400 2
*DATE*TIME* CADD FILE No. PSP108\CAD\250\PIPE SUPPORT STANDARDS\DSPSH400.DGN
SEE NOTE 6
"L"
BOTTOM OF STEEL SEE NOTE 6

OR CONCRETE "W"
HANGER PLATE WELDED ATTACHMENT ANVIL INTL.

PER DS-PS-X758 FIG. 66 OR EQUAL
IF SPEC. ON DWG.
"H" AS SHOWN IN DRAWING WELDLESS EYE NUT ANVIL INTL.

FIG. 290 OR EQUAL
FOR ROD LENGTHS GREATER THAN 3m,

ADD TURNBUCKLE ANVIL INTL. FIG. 230
OR EQUAL c/w 2 LOCK NUTS.
SIZE TO MATCH ROD DIAMETER OF UPPER &
LOWER HANGER ASSEMBLY.
HANGER ROD DIA. PER TABLES

ON DESIGN STANDARD DS-PS-121.
c/w LOCK NUTS.
WELDLESS EYE NUT ANVIL INTL.

FIG. 290 OR EQUAL
REINFORCING PADS PER

DESIGN STANDARD
DS-PS-S615 FOR
ALL PLASTIC LINES
PIPE CLAMP ( SEE NOTE 1 )

MODERATE LOADS: ANVIL INTL.
FIG. 212 OR EQUAL
HEAVY LOADS: ANVIL INTL.
FIG. 216 OR EQUAL
NOTES:
1. DESIGNER TO REFER TO DESIGN STANDARD DS-PS-113 & DS-PS-121 FOR ROD & CLAMP CAPACITIES.
2. FIELD SELECTION OF PIPE CLAMPS TO BE MADE PER HANGER SPACING TABLES
IN PIPE SUPPORT SPECIFICATION.
3. WHEN WELDING TO U/S OF A LOAD BEAM, THE WELDING BEAD "W" SHOULD ALWAYS BE
APPLIED TO A DIRECTION PARALLEL TO THE BEAM’S LONGITUDINAL CENTERLINE.
4. THIS STANDARD APPLIES TO UNINSULATED LINES ONLY.
5. ROD AND HANGER COMPONENTS SHALL BE THE SAME MATERIAL.
6. DESIGNER TO REFER TO DESIGN STANDARD DS-PS-H400 FOR ROD AND WELD SIZES.
ANVIL INTL. PIPE

SUPPORT
CLAMP TYPE OR EQ.
TAG
/ MATERIAL
410A FIG. 212 / C.S.
410B FIG. 216 / C.S.
410AS FIG. 212 / 316 S.S.
410BS FIG. 216 / 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-113/121, DS-PS-S614/S615, DS-PS-X758,DS-PS-H400
J.M.D./T.G.
DATE
0 T.G.
03/28/95
ISS’D FOR CONSTRUCTION H.L. CH. Y.T. HANGER ASSEMBLY
1 J.H. RODS & NUTS DELETED SUP. DESIGN STANDARD NO. REV.
H.LESKIE
12/01/97
2 T.G.
10/22/04
DATE 03/28/95 DS-PS-H410 2
SEE NOTE 6
"L"
BOTTOM OF STEEL SEE NOTE 6

OR CONCRETE "W"
HANGER PLATE WELDED ATTACHMENT ANVIL INTL.

PER DS-PS-X758 FIG. 66 OR EQUAL
IF SPEC. ON DWG.

FIG. 290 OR EQUAL
"H" AS SHOWN IN DRAWING FOR ROD LENGTHS GREATER THAN 3m,

HANGER ROD DIA. PER TABLES

ON DESIGN STANDARD DS-PS-122.
c/w LOCK NUTS.

FIG. 290 OR EQUAL

DESIGN STANDARDS
FOR THIN WALL PIPE WITH
CLAMP WIDTHS < 4" AND ALL
PLASTIC LINES
PIPE CLAMP ( SEE NOTE 1 )

MODERATE LOADS: ANVIL INTL.
FIG. 295 OR EQUAL
HEAVY LOADS: ANVIL INTL.
FIG. 295H OR EQUAL
NOTES:
1. DESIGNER TO REFER TO DESIGN STANDARD DS-PS-113 & DS-PS-122 FOR ROD & CLAMP CAPACITIES.
2. FIELD SELECTION OF PIPE CLAMPS TO BE MADE PER HANGER SPACING TABLES
IN PIPE SUPPORT SPECIFICATION.
ANVIL INTL. PIPE

SUPPORT
CLAMP TYPE OR EQ.
TAG
/ MATERIAL
411A FIG. 295 / C.S.
411B FIG. 295H / C.S.
411AS FIG. 295 / 316 S.S.
411BS FIG. 295H / 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-113/122, DS-PS-S614/S615, DS-PS-X758,DS-PS-H400
J.M.D./T.G.
DATE
0 T.G.
03/28/95
1 J.H. RODS & NUTS DELETED Y.T. SUP. DESIGN STANDARD NO. REV.
H.LESKIE
12/01/97
2 T.G.
10/22/04
DATE 03/28/95 DS-PS-H411 2
SEE NOTE 4 SEE NOTE 4
"L" "L"
BOTTOM OF STEEL OR CONCRETE
SEE HANGER PLATE PER DS-PS-X758

NOTE 4 IF SPEC. ON DWG.
"W"
HANGER RODS, DIA. PER TABLES

ON DESIGN STANDARD DS-PS-125
c/w LOCK NUTS.
"H" AS SHOWN IN DRAWING
SIZE OF ROD DIAMETER TO MATCH

UPPER & LOWER HANGER ASSEMBLY.


FOR THIN WALL ONLY
LENGTH "B" TO SUIT
50 MIN.

FIG. 290 OR EQUAL
C EL. SPECIFIED
ON PLAN
50 MIN.
DOUBLE RISER CLAMP

ANVIL INTL. FIG. 40/40SD OR EQUAL
C/W SHEAR LUGS
SEE NOTE 1
NOTES:
1. DESIGNER TO REFER TO DESIGN STANDARDS DS-PS-113, DS-PS-123 AND DS-PS-125
FOR ROD, CLAMP AND SHEAR LUG CAPACITIES AND DIMENSIONS.

RISER CLAMP
SUPPORT
TYPE ( SEE NOTES )
TAG
/ MATERIAL
414A FIG. 414A / C.S.
414B FIG. 414B / C.S.
414C FIG. 414C / C.S.
414D FIG. 414D / C.S.
414AS FIG. 414A / 316 S.S.
414BS FIG. 414B / 316 S.S.
414CS FIG. 414C / 316 S.S.
414DS FIG. 414D / 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-113/123/125, DS-PS-S600, DS-PS-H400
J.M.D./T.G.
DATE
0 T.G.
03/28/95
2 SUP. H.LESKIE
3 D.K.
11/23/05
REVISED REPAD DETAIL B.C. DATE 03/28/95 DS-PS-H414 3
SEE NOTE 6 SEE NOTE 6
"L" "L"
BOTTOM OF STEEL OR CONCRETE
HANGER PLATE PER DS-PS-X758

"W" SEE
IF SPEC. ON DWG.
"W" NOTE 6
HANGER ROD, 50 DIA.

c/w LOCK NUTS.
SIZE OF ROD DIAMETER TO MATCH

UPPER & LOWER HANGER ASSEMBLY.

STEEL CLEVIS ANVIL INTL.

FIG. 299 OR EQUAL
C EL. SPECIFIED
ON PLAN
WELDING LUG ANVIL INTL.

FIG. 55 OR EQUAL
REINFORCING PAD PER

DESIGN STANDARD
DS-PS-S600
NOTES:
1. THIS HANGER ASSEMBLY IS TO BE USED ONLY FOR LINES 4" dia. AND LESS.
2. REFER TO ANVIL INTL. CATALOG FOR MAXIMUM RECOMMENDED LOADS.

5. DESIGNER TO REFER TO DESIGN STANDARD DS-PS-113 FOR ROD CAPACITIES.
SUPPORT HANGER
TAG MATERIAL
416 C.S.
416S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-S600, DS-PS-113, DS-PS-H400
J.M.D./T.G.
DATE
0 T.G.
03/28/95
1 J.H. RODS & NUTS DELETED Y.T. SUP. DESIGN STANDARD NO. REV.
H.LESKIE
12/01/97
2 T.G.
10/22/04
DATE 03/28/95 DS-PS-H416 2
SEE NOTE 6
"L"
BOTTOM OF STEEL
OR CONCRETE
HANGER PLATE PER DS-PS-X758

IF SPEC. ON DWG.
"W"
WELDED ATTACHMENT ANVIL INTL.

FIG. 66 OR EQUAL

FIG. 290 OR EQUAL

HANGER ROD, DIA. "A"

PER TABLE. c/w LOCK NUTS
ADJUSTABLE CLEVIS
ANVIL INTL. FIG. 260 OR EQUAL
NOM. ROD BOLT CAPACITY LENGTH SIZE OF

PIPE DIA. DIA. IN OF WELD FILLET"W"
DIA. "A" "B" kN "L"
MIN. MAX.
"B"
3/4" 3/8" 1/4" 2.7 20 3 7
1" 3/8" 1/4" 2.7 20 3 7
1 1/2" 3/8" 1/4" 2.7 20 3 7
2" 3/8" 1/4" 2.7 20 3 7
2 1/2" 1/2" 3/8" 5.0 20 3 7
3" 1/2" 3/8" 5.0 20 3 7
4" 5/8" 3/8" 6.3 20 5 7
6" 3/4" 1/2" 8.6 20 7 10
8" 7/8" 5/8" 8.9 32 7 10
10" 7/8" 3/4" 16.0 32 7 10
12" 7/8" 3/4" 16.9 32 7 10 SEE NOTE 1
14" 1" 7/8" 18.6 32 10 13
16" 1" 1" 20.4 32 10 13
18" 1" 1 1/8" 21.3 32 10 13
20" 1 1/4" 1 1/4" 21.3 32 13 16
24" 1 1/4" 1 1/4" 21.3 32 13 16
NOTES:
1. REINFORCING PADS REQUIRED FOR PLASTIC PIPE PER DESIGN STANDARD DS-PS-S601.
SUPPORT HANGER
TAG MATERIAL
418 C.S.
418S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-S601, DS-PS-113, DS-PS-H400
J.M.D./T.G.
DATE
0 T.G.
03/28/95
1 J.H. ROD & NUTS DELETED SUP. DESIGN STANDARD NO. REV.
H.LESKIE
12/01/97
2 T.G.
10/22/04
DATE 03/28/95 DS-PS-H418 2
FOR 10mm AND
SEE NOTE 2
7 GREATER PLATE
50-125
FOR 6mm PLATE

5 50-125
FOR 3mm PLATE

3 50-125
CARBON
STAINLESS OR
ALLOY PIPE
REINFORCING PAD THICKNESS

SEE NOTE 1
"B" = 455
OR AS SPEC. ON DWG
SUPPORT SUPPORT
TAG MATERIAL
"
"T
S600 C.S.
S600S 316SS
60^ 60^ VENT HOLE
S600A ALLOY
SEE NOTE 4 SEE NOTE 4 SEE NOTE 3
NOTES:
1. REINFORCING PADS SHALL BE MADE FROM THE SAME MATERIAL AND THICKNESS
AS PIPE, SHAPED TO SUIT, O.D. OF PIPE.
2. USE INTERMITTENT FILLET WELDS ON PADS FOR STAINLESS OR ALLOY PIPE.

RUBBER LINED OR INTERNALLY COATED PIPE, LUGS TO BE SHOP WELDED PRIOR TO
RUBBER LINING/INTERNAL COATING. ALL OTHERS TO BE FIELD WELDED.
3. 3mm dia. VENT HOLE IS REQUIRED ONLY WHEN CONTINUOUS FILLET IS APPLIED.
4. PAD ANGLE TO BE 90^ FOR PIPES 4" dia. AND SMALLER.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-S601
J.M.D./T.G.
DATE
0 T.G.
03/28/95
ISS’D FOR CONSTRUCTION H.L. CH. Y.T. SUPPORT
1 T.G. TAG TABLE ADDED SUP. DESIGN STANDARD NO. REV.
H.LESKIE
10/22/04
2 D.K.
11/18/05
PAD THICKNESS REVISED DATE 03/28/95 DS-PS-S600 2
*DATE*TIME* CADD FILE No. PSP108\CAD\250\PIPE SUPPORT STANDARDS\DSPSS600.DGN
SEE NOTE 2
16^
CARBON,
STAINLESS OR
ALLOY PIPE
EXCEPT AS NOTED FOR 3" AND 4"

PIPE, REINFORCING PADS MAY BE
CUT FROM 45^ ELBOWS
(SEE NOTES 1 & 4)
29^
SUPPORT SUPPORT
TAG MATERIAL
S602 C.S.
"
"T
S602S 316SS
S602A ALLOY 60^ 60^ VENT HOLE
SEE NOTE 4 SEE NOTE 4 SEE NOTE 3
NOTES:
1. REINFORCING PADS SHALL BE MADE FROM THE SAME MATERIAL & WALL THICKNESS
AS PIPE, SHAPED TO SUIT.
2. USE INTERMITTENT FILLET WELDS ON PADS FOR STAINLESS OR ALLOY PIPE.

FILLET WELDS TO BE SAME THICKNESS AS PAD THICKNESS.
RUBBER LINED OR INTERNALLY COATED PIPE, LUGS TO BE SHOP WELDED PRIOR TO
RUBBER LINING/INTERNAL COATING. ALL OTHERS TO BE FIELD WELDED.
3. 3mm dia. VENT HOLE IS REQUIRED ONLY WHEN CONTINUOUS FILLET IS APPLIED.
4. PAD ANGLE TO BE 90^ AND LENGTH 2 x DIA. FOR PIPES 4" dia. AND SMALLER.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS

J.M.D./T.G.
DATE
0 T.G.
03/28/95
1 T.G. GENERAL REVISION SUP. DESIGN STANDARD NO. REV.
H.LESKIE
10/22/04
DATE 03/28/95 DS-PS-S602 1

REINFORCING PAD PER
OR "H" AS SPEC.
DESIGN STANDARD
DS-PS-S600 FOR
ON DRAWING
THIN WALL ONLY
CARBON STEEL
OR THIN WALL
PIPE
B.O.P.
100
WITH
12
5 REPAD
13
TYP.
TYP
38X25
WITHOUT
5 INSULATION
REPAD
BAND SLOT
455
10 12
5 3 25-50 5 3 25-60
20
20
75 150
IF REQUIRED,
INCLUDE ROD FOR
PIPES 1" TO 4" DIA. PIPES 6" TO 10" DIA.
SLOPED LINES.
SEE NOTE 3
NOTES:
1. THIS SUPPORT IS APPLICABLE TO LINES 1" TO 10" ONLY.
3. ROD SHALL BE SHIPPED LOOSE WITH SHOE.
SUPPORT SUPPORT
TAG MATERIAL
603 C.S.
603R C.S. ROD & SHOE
603S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-S600
J.M.D./T.G.
DATE
0 T.G.
03/28/95
1 SUP. H.LESKIE
10/22/04 WIDTH CHG’D FOR SMALL PIPE SHOE
2 D.K.
11/18/05
C.S. ROD OPTION ADDED B.C. DATE 03/28/95 DS-PS-S603 2
REINFORCING PAD PER
DESIGN STANDARD
OR "H" AS SPEC.
DS-PS-S600 FOR
THIN WALL ONLY
ON DRAWING
CARBON STEEL IF SPECIFIED ON DRAWING.
OR THIN WALL
PIPE
B.O.P.
100
WITH
12
7 REPAD
13
TYP.
TYP
38x25
WITHOUT
7 INSULATION
REPAD
BAND SLOT
455
12
TYP TYP
7 IF REQUIRED,
INCLUDE ROD FOR SLOPED LINES.
SEE NOTE 3
20
175
305
5 25-140
NOTES:
SUPPORT SUPPORT
TAG MATERIAL
604 C.S.
604S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-S600
J.M.D./T.G.
DATE
0 T.G.
03/28/95
H.LESKIE
10/22/04
2 D.K.
11/18/05
OR "H" AS SPEC.
ON DRAWING
TYP
CARBON STEEL PIPE 7 150
REINFORCING 38x25 INSULATION
PAD PER BAND SLOT
DS-PS-S600 TYP
7 150
B.O.P.
100
IF REQUIRED,
INCLUDE ROD
FOR SLOPED LINES.
12
SEE NOTE 3
20
"D"
150 150
455
5 "L"-"P"
TYP
5 100-165
90
PIPE
"A" "D" "L" "P"
DIA.
TYP
5 20" 305 485 50 215
"A"
TYP.
24" 380 560 50 255

12
28" 455 635 50 290
30" 510 690 50 320
32" 560 740 75 330

90
36" 610 790 75 350

13
TYP.
NOTES:
SUPPORT SUPPORT
TAG MATERIAL
605 C.S.
605S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-S600
J.M.D./T.G.
DATE
0 T.G.
03/28/95
H.LESKIE
10/22/04
2 D.K.
11/18/05
6x100 RUBBER
OR "H" AS SPEC.
PAD AROUND PLASTIC
PIPE ONLY
ON DRAWING
( SEE NOTE 3 )
NON-THIN WALL
S.S., ALLOY, PLASTIC,
RUBBER-LINED C.S. OR
INTERNALLY COATED PIPE
100
TYP.
12
5
13
TYP. 38x25
INSULATION
BAND SLOT
455
PIPE CLAMP PIPE CLAMP

ANVIL INTL. FIG. 212 ANVIL INTL. FIG. 212
OR EQUAL OR EQUAL
IF REQUIRED,
10 12 INCLUDE ROD
FOR SLOPED LINES.
3 25-50 5
5 SEE NOTE 4
20
20
75 150
3 25-60
PIPES 1" TO 4" DIA. PIPES 6" TO 10" DIA.
NOTES:
SUPPORT SUPPORT
TAG MATERIAL
606 C.S.
606S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS

J.M.D./T.G.
DATE
0 T.G.
03/28/95
1 SUP. H.LESKIE
10/22/04 WIDTH CHG’D FOR SMALL PIPE SHOE
DATE 03/28/95 DS-PS-S606 1

6x100 RUBBER
PAD AROUND PLASTIC
OR "H" AS SPEC.
PIPE ONLY
NON-THIN WALL ( SEE NOTE 3 )
ON DRAWING
S.S., ALLOY,
PLASTIC,
RUBBER-LINED C.S.,
OR INTERNALLY COATED PIPE
100
TYP.
12
7
13
TYP.
38x25
INSULATION
BAND SLOT
455
PIPE CLAMP
OR EQUAL
12
TYP TYP
7 IF REQUIRED,
INCLUDE ROD FOR SLOPED LINES.
SEE NOTE 4
20
175
305
5 25-140
NOTES:
SUPPORT SUPPORT
TAG MATERIAL
607 C.S.
607S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS

J.M.D./T.G.
DATE
0 T.G.
03/28/95
1 T.G. "GRINNELL" CHG’D TO "ANVIL INTL." SUP. DESIGN STANDARD NO. REV.
H.LESKIE
10/22/04
DATE 03/28/95 DS-PS-S607 1

"B"
6 x "C" RUBBER
PAD AROUND PLASTIC
PIPE ONLY
( SEE NOTE 3 )
NON-THIN WALL
OR "H" AS SPEC.
S.S., ALLOY,
ON DRAWING
PLASTIC,
RUBBER LINED
C.S. OR
INTERNALLY COATED PIPE
B.O.P.
100
IF REQUIRED,
INCLUDE ROD
FOR SLOPED LINES.
12
SEE NOTE 4
20
"D"
38x25 TYP
INSULATION 7
BAND SLOT
150 150
PIPE CLAMP ANVIL INTL. OR EQUAL.
SEE TABLE FOR FIG. No.
455
5 "L"-"P"
TYP
5 100-165
90
PIPE ANVIL INTL.

"A" "B" "C" "D" "L" "P"
DIA. CLAMP
TYP 20" 305 455 100 485 50 215 FIG. 212/212S

5
"A"
24" 380 455 125 560 50 255 FIG. 212/212S

TYP.
12
28" 455 660 255 635 50 290 FIG. 216/216S
30" 510 660 255 690 50 320 FIG. 216/216S
32" 560 660 255 740 75 330 FIG. 216/216S

90
13 36" 610 660 255 790 75 350 FIG. 216/216S
TYP.
NOTES:
SUPPORT SUPPORT
TAG MATERIAL
608 C.S.
608S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS

J.M.D./T.G.
DATE
0 T.G.
03/28/95
1 T.G. "GRINNELL" CHG’D TO "ANVIL INTL." SUP. DESIGN STANDARD NO. REV.
H.LESKIE
10/22/04
DATE 03/28/95 DS-PS-S608 1

PIPE CLAMP ANVIL INTL. FIG. 212 OR
EQUAL FOR PIPE SIZE 30" AND UNDER
PIPE CLAMP ANVIL INTL. FIG. 216 OR
EQUAL FOR PIPE SIZE 36"
ROTATE 25^
IF REQUIRED
"D"
CENTER END PLATE
"C"
"B"
PLATE 3
"W"
2
3 2 TEE 1
"A" "T" "E" "F"
TYP.
TEE PLATE PLATE SIZE OF

PIPE SIZE QTY QTY
"A" "B" "C" "D" "E" "F" "T" FILLET
SIZE
1 2 3 "W"
1 1/2" WT 100x13.5 38 89 93 113 - - - - - 5
2" WT 100x13.5 50 89 93 119 - - - - - 5
3" WT 100x13.5 75 89 100 133 - - - - - 5
4" WT 100x13.5 75 89 95 146 - - - - - 5
6" WT 125x16.5 114 100 112 186 - - - - - 5
8" WT 155x30 150 100 120 211 63.5 - 10 1 - 5
10" WT 155x30 175 100 118 238 63.5 - 10 1 - 5
12" WT 155x30 216 100 126 264 63.5 - 10 1 - 5
14" WT 155x30 230 100 127 279 - 125 10 - 2 5
16" WT 155x30 255 100 130 305 - 125 10 - 2 5
18" WT 155x30 280 100 130 330 - 125 10 - 2 7
20" WT 155x30 305 100 133 356 - 125 10 - 2 7
24" WT 155x30 380 100 148 406 63.5 150 10 1 2 7
28" WT 180x32 455 125 164 457 63.5 125 12 1 2 7
30" WT 180x32 510 125 199 508 63.5 125 12 1 2 7
36" WT 180x32 610 125 218 584 63.5 150 12 1 2 7
NOTES:
1. THIS SUPPORT IS NOT TO BE USED BY ITSELF.
USE WITH DS-PS-A208, DS-PS-A210, DS-PS-S610 OR DS-PS-S611 ONLY.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-A208, DS-PS-A210, DS-PS-S610
J.M.D./T.G.
DATE
0 T.G.
03/28/95
SUP. H.LESKIE
DATE 03/28/95 DS-PS-S609 1

SUPPORT FIG. 609
SEE DESIGN STANDARD
DS-PS-S609
STD. WT. PIPE
"L"
7
"C"
7mm dia. VENT HOLE
BASE PLATE
7
GROUT OR CONCRETE
PEDESTAL WHERE
WEAR PLATE PER APPLICABLE
DESIGN STANDARD
DS-PS-X757 IF
SPECIFIED ON
DRAWING
PIPE "L" BASE WEAR

"C"
SIZE MAX. PLATE PLATE
3" - 4" 2" 610 10x150x150
6" 3" 760 10x150x150

TYPE 1
8" 4" 915 10x230x230
10" - 12" 4" 915 10x230x230
14" 6" 915 12x305x305
16" 6" 915 12x305x305 TYPE 2
18" 6" 915 12x305x305
SUPPORT SUPPORT
TAG MATERIAL
610 C.S.
610S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
J.M.D./T.G.
DATE
0 T.G.
03/28/95
1 T.G. FIELD WELD ADDED H.L. SUP. DESIGN STANDARD NO. REV.
H.LESKIE
05/16/95
2 T.G.
10/22/04
REF. STANDARDS ADDED DATE 03/28/95 DS-PS-S610 2
FLANGE
MATCH FLANGE BOLT DRILLING ON (2)

HOLES FOR ATTACHMENT. CUT TEE TO
SUIT PIPE O.D.
USE TEE AS IN FIG. 609 (EXCEPT
DIM "A"=150mm FOR 3" TO 6" DIA. PIPE)
SEE DESIGN STANDARD
7
DS-PS-S609
"L"
"C" STD. WT. PIPE
7mm dia. VENT HOLE
BASE PLATE
7
GROUT OR CONCRETE
PEDESTAL WHERE
WEAR PLATE PER APPLICABLE
DESIGN STANDARD
DS-PS-X757 IF
SPECIFIED ON
DRAWING
PIPE "L" BASE WEAR

"C"
3" - 4" 2" 610 10x150x150
6" 3" 760 10x150x150

TYPE 1
8" 4" 915 10x230x230
10" - 12" 4" 915 10x230x230
14" 6" 915 12x305x305
16" 6" 915 12x305x305 TYPE 2
18" 6" 915 12x305x305
SUPPORT SUPPORT
TAG MATERIAL
611 C.S.
611S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
J.M.D./T.G.
DATE
0 T.G.
03/28/95
H.LESKIE
05/16/95
2 T.G.
10/22/04
REINFORCING PAD PER
DESIGN STANDARD
7 DS-PS-S602 OR DS-PS-S600
ON DRAWING
SPECIFIED
"L" STD. WT. PIPE
"C"
7mm dia. VENT HOLE
BASE PLATE
7
GROUT OR CONCRETE
PEDESTAL WHERE
APPLICABLE
WEAR PLATE PER
DESIGN STANDARD
DS-PS-X757 IF
SPECIFIED ON
DRAWING
PIPE "L" BASE WEAR

"C"
3" - 4" 2" 610 10x150x150
6" 3" 760 10x150x150 TYPE 1
8" 4" 915 10x230x230
10" - 12" 4" 915 10x230x230
14" 6" 915 12x305x305
16" 6" 915 12x305x305 TYPE 2
18" 6" 915 12x305x305
20" - 30" 10" 1000 20x425x425 TYPE 3
SUPPORT SUPPORT
TAG MATERIAL
612 C.S.
612S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-S600, DS-PS-S602, DS-PS-X757
J.M.D./T.G.
DATE
0 T.G.
03/28/95
H.LESKIE
05/16/95
2 T.G.
10/22/04
REINFORCING PAD PER
DESIGN STANDARD
DO NOT CUT
"T" HOLE IN PIPE
STD. WT. DUMMY

PIPE
6mm END PLATE
B.O.P. ELEV.
SPEC. ON DWG
7mm dia. VENT HOLE
"L" 305
SPEC. ON
DWG
SEE NOTE 1 NOM. DUMMY
PIPE PIPE
DIA. DIA.
3" 3"
4" 3"
"T" = DUMMY PIPE 6" 4"

WALL THK.
8" 6"
10" 6"
12" 8"
14" 10"
16" 10"
18" 12"
SUPPORT SUPPORT 20" 14"
TAG MATERIAL
24" 14"
613 C.S. 30" 16"
613S 316 S.S. 36" 20"
NOTES:
1. "L" DIMENSION TO BE CALCULATED BY STRESS ENGINEER.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-S600, DS-PS-S602
J.M.D./T.G.
DATE
0 T.G.
03/28/95
1 T.G. REF. STANDARDS ADDED H.L. SUP. DESIGN STANDARD NO. REV.
H.LESKIE
10/22/04
2 D.K.
11/18/05
NOTE 1 ADDED B.C. DATE 03/28/95 DS-PS-S613 2
PIPE CLAMP AS
PLASTIC
PIPE
= =
REINFORCING PAD
SEE NOTE 1.
B = 1/2 PIPE DIA. THICKNESS :

2"-4" dia. : "T" = 3mm
OR 150mm MIN. 6"-24" dia. : "T" = 6mm
26"-36" dia. : "T" = 10mm
"T
"
60^ 60^
TYP. TYP.
NOTES:
1. WHERE REPAD OVERLAPS BUTT FUSION WELD BEAD, EXTERNAL BEAD IS TO BE
REMOVED PER MANUFACTURERS INSTRUCTIONS.
SUPPORT SUPPORT
TAG MATERIAL
615 C.S.
615S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-H410/H411
DATE
CH. SUPPORT
SUP. DESIGN STANDARD NO. REV.
DATE DS-PS-S615 0
FOR THIN WALL ONLY
LENGTH "B" TO SUIT
50 MIN. DOUBLE RISER CLAMP

ANVIL INTL. FIG. 40 OR EQUAL
C/W SHEAR LUGS
SEE NOTE 1
LOCATION SPECIFIED
ON DRAWING
SEE NOTE 3
50 MIN.
REINFORCING PADS
PER DESIGN STANDARD
DS-PS-S614 FOR
THIN WALL ONLY
PIPE 6" dia. & LARGER IF SPECIFIED ON DRAWING

150 150
CLAMP TYPE
MAX. LOCATION SPECIFIED
ON DRAWING
SEE NOTE 3
65
6mm PLATE
RISER LUG
TYP.
TYP. OR
SEE NOTE 2
5 5
PIPE 4" dia. & SMALLER
LUG TYPE
CLAMP OR LUG
SUPPORT
TYPE ( SEE NOTES )
NOTES: TAG
/ MATERIAL
1. DESIGNER TO REFER TO DESIGN STANDARDS DS-PS-123 AND
DS-PS-125 FOR CLAMP AND SHEAR LUG CAPACITIES AND 616A FIG. 414A / C.S.
SHEAR LUG CAPACITIES AND DIMENSIONS.
616B FIG. 414B / C.S.
2. FIELD WELD APPLIES ONLY TO NON-RUBBER LINED PIPE.
616C FIG. 414C / C.S.
FOR RUBBER LINED PIPE, LUGS TO BE SHOP WELDED.
616D FIG. 414D / C.S.
3. FOR RUBBER LINED PIPE, INCLUDE 20 mm SHIM ALLOWANCE
OR AS SPECIFIED ON DRAWING. 616E LUG TYPE / C.S.
616AS FIG. 414A / 316 S.S.
616BS FIG. 414B / 316 S.S.
616CS FIG. 414C / 316 S.S.
616DS FIG. 414D / 316 S.S.
616ES LUG TYPE / S.S
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-S600, DS-PS-614, DS-PS-123, DS-PS-124
J.M.D./T.G.
DATE
0 T.G.
03/28/95
1 Y.T. SUP. H.LESKIE
2 D.K.
11/21/05
ADDED WELD NOTES FOR
RUBBER LINED PIPE
B.C. DATE 03/28/95 DS-PS-S616 2
STRUCTURAL STEEL MEMBER DETAILS
& CODE NUMBERS
MAX.
STEEL MAX.
STEEL FLANGE
CODE LAYOUT ROD
MEMBER BOLT
NUMBER DIA.
DIA.
1 L64 x 64 x 9.5 1/2
2 L102 x 102 x 9.5 3/4
3 (2) L102 x 102 x 9.5 5/8
4 C100 x 8 5/8
5 (2) C100 x 8 5/8
6 C150 x 12.2 5/8
7 (2) C150 x 12.2 3/4
8 W100 x 19.3 5/8
9 W150 x 22.5 3/4
10 W200 x 26.6 3/4
11 W250 x 32.7 3/4
12 W310 x 38.7 3/4
NOTES
1. SUPPORT STEEL MEMBERS SHALL BE SPECIFIED IN THE PIPE SUPPORT IDENTIFICATION

BLOCK USING THE SIZE DESIGNATING NUMBERS ABOVE.
2. THE STRUCTURAL MEMBERS SPECIFIED FROM THE ABOVE TABLE ARE OF THE MINIMUM
WEIGHT REQUIRED. IF A MEMBER IS NOT AVAILABLE AS SPECIFIED ABOVE, IT SHOULD
BE SUBSTITUTED WITH A MEMBER OF THE SAME SIZE BUT WITH A HEAVIER WEIGHT.
3. STRUCTURAL ANGLES WHEN REQUIRED FOR THE SUPPORT OF HANGER RODS SHALL BE
INSTALLED WITH THEIR HORIZONTAL LEG AT THE BOTTOM TO FACILITATE THE WELDING
OF A HANGER ROD BEAM ATTACHEMENT. USE MEMBERS 1 & 2 ONLY FOR LIGHT LOADS.
4. ALL WELDS TO STRUCTURAL STEEL ARE 5mm FILLET, EXCEPT 7mm FILLET FOR
MEMBERS 10, 11 AND 12. WELDS SHALL BE ALL AROUND WHERE POSSIBLE.
5. WHEN WELDING TO U/S OF A LOADED BEAM, THE WELDING BEAD SHOULD ALWAYS BE
APPLIED IN A DIRECTION PARALLEL TO THE BEAM’S LONGITUDINAL CENTERLINE.
6. WHEN A 316 S.S. MEMBER IS REQUIRED AND IS NOT AVAILABLE AS SPECIFIED ABOVE,
IT SHOULD BE FABRICATED FROM HOT-ROLLED PLATES TO DIMENSIONS SIMILAR TO
THOSE OF THE SPECIFIED STEEL MEMBER.
7. EXCEPT WHERE NOTED, THESE DETAILS ARE INTENDED FOR ATTACHMENT TO STEEL
OR CONCRETE STRUCTURES OR TANKS ONLY. SUITABILITY FOR OTHER APPLICATIONS
MUST BE CONFIRMED PRIOR TO USE.
8. ALL CARBON STEEL STRUCTURAL MEMBERS ARE TO BE PAINTED PER PROJECT STANDARDS.
9. DESIGNER IS RESPONSIBLE FOR SELECTING THE APPROPRIATE STEEL CODE NUMBER

TO SUIT PIPE LOADING.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS

J.M.D./T.G.
DATE
0 T.G.
EXTRA STEEL
ISS’D FOR CONSTRUCTION H.L. CH. Y.T.
03/28/95
SUP. DESIGN STANDARD NO. REV.

H.LESKIE
DATE 03/28/95 DS-PS-X700 0

STEEL CODE No. CLIP ANGLE
(PER DS-PS-X700) TYPE
6 - 9 - 10 - 11 - 12 "A"
2 - 4 - 8 "B"
USE 5/8" ^ A325 BOLTS
CLIP ANGLE TYPE "A" CLIP ANGLES TYPE "B"

L 102 x 102 x 9.5 21 20 2-L 152 x 102 x 9.5
18
SLOT DETAIL
DIMENSION TO SUIT 63 +
-
TYP.
SLOT. SEE 38 +
-
DETAIL TYP.
=
NEW STEEL AS SPECIFIED

ON DWG. SEE DESIGN STANDARD
No. 6 & 9
FOR STEEL CODE
FOR STEEL CODE

=
100
DS-PS-X700
No. 10, 11 & 12

63
C HOLES FOR CLIP CLIP ANGLE

ANGLE TYPE "B" TYPE "A" OR "B"
DRILL 18mm dia. HOLES

IN EXISTING STEEL
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-X700
J.M.D./T.G.
DATE
0 T.G.
EXTRA STEEL
03/28/95

H.LESKIE
10/22/04
DATE 03/28/95 DS-PS-X701 1

EXTRA STEEL MEMBER SPECIFIED
ON PIPE SUPPORT DRAWING
FOR STEEL MEMBER CODE AND
WELDING FILLET SIZE, SEE
DESIGN STANDARD DS-PS-X700 "A"
AS SPEC. ON DWG.
T.O.S. ELEV.
SPEC. ON PLAN
"L" ( MAX. )
LOCATE ADDITIONAL STEEL MEMBER AS

HIGH AS POSSIBLE BETWEEN BEAMS
FOR BOLTED ATTACHMENT

COMPONENTS AND DETAIL,
SEE DESIGN STANDARD
DS-PS-X701
STEEL CODE MAXIMUM MAXIMUM

NUMBER SPAN "L" LOAD (kN)
8 1830 22.2
9 3050 31.1
10 4270 22.2
NOTES:
1. MAXIMUM SPANS AND LOADS INDICATED REPRESENT VERTICAL LOADING ONLY,
WHERE ANCHORS, OR DIRECTIONAL ANCHORS ARE USED IN CONJUNCTION
WITH THIS DETAIL, STEEL SIZE SELECTION SHALL BE APPROVED BY THE
STRUCTURAL ENGINEER.
2. FOR SPANS OR VERTICAL LOADS GREATER THAN THOSE LISTED, STEEL SIZE SELECTION
SHALL BE APPROVED BY THE STRUCTURAL ENGINEER.
3. WHEN USED FOR SUPPORTING MULTIPLE PIPES, DESIGNER MUST PROVIDE DIMENSION "A"
FOR ONLY ONE PIPE.
SUPPORT ATTACHEMENT
TAG TYPE / MATERIAL
702B BOLTED / C.S.
702W WELDED / C.S.
702BS BOLTED / 316 S.S.
702WS WELDED / 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-X700, DS-PS-X701
J.M.D./T.G.
DATE
0 T.G.
EXTRA STEEL
03/28/95

H.LESKIE
10/22/04
DATE 03/28/95 DS-PS-X702 1

DESIGN STANDARD DS-PS-X700
"A"
AS SPEC.
ON DWG.
T.O.S. ELEV.
SPEC. ON PLAN
FOR BOLTED ATTACHMENT

COMPONENTS AND DETAIL,
SEE DESIGN STANDARD
DS-PS-X701 OR DS-PS-X753
FOR ATTACHING TO CONCRETE.
"L" ( MAX. )

8 1830 22.2
9 3050 31.1
10 4270 22.2
NOTES:
FOR ONLY ONE PIPE.
SUPPORT ATTACHEMENT
TAG TYPE / MATERIAL
703B BOLTED / C.S.
703W WELDED / C.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-X700, DS-PS-X701, DS-PS-X753
J.M.D./T.G.
DATE
0 T.G.
EXTRA STEEL
03/28/95

H.LESKIE
10/22/04
DATE 03/28/95 DS-PS-X703 1

25mm Min. CLEARANCE BETWEEN
STEEL AND PIPE MATERIAL
(INSULATION, U-BOLTS,
HANGERS, ETC)
FOR BOLTED CONNECTION

SEE DESIGN STANDARD
DS-PS-X701 TYPE "B"
"A"
AS SPEC.
ON DWG.
"B"
SEE NOTE 4
"C"
"L" ( MAX. )
"D"
WT75 x 11
FOR BOLTED CONNECTION EXTRA STEEL MEMBER SPECIFIED

SEE DESIGN STANDARD ON PIPE SUPPORT DRAWING
DS-PS-X701 FOR STEEL MEMBER CODE AND
STEEL CODE MAXIMUM MAXIMUM LOAD

NUMBER SPAN "L" PER LEVEL (kN)
4 1520 8.9
8 1520 22.2
NOTES:
3. THIS SUPPORT IS FOR A MAXIMUM OF THREE LEVELS ONLY
4. DESIGNER SHALL PROVIDE DIMENSION "A" FOR ONE PIPE ONLY.
SUPPORT ATTACHEMENT
TAG TYPE / MATERIAL
704B BOLTED / C.S.
704W WELDED / C.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
J.M.D./T.G.
DATE
0 T.G.
EXTRA STEEL
03/28/95

H.LESKIE
10/22/04
2 D.K.
11/21/05
DIMENSIONS LABELLED B.C. DATE 03/28/95 DS-PS-X704 2
BEAM LOADING TO BE
APPROVED BY THE
FOR BOLTED CONNECTION

SEE DESIGN STANDARD
DS-PS-X701 TYPE "B"
"A"
AS SPEC.
ON DWG.
"B"
SEE NOTE 4
"C"
"L" ( MAX. )
"D"
WT75 x 11
( TYP.)
EXTRA STEEL MEMBER SPECIFIED 25mm Min. CLEARANCE BETWEEN

ON PIPE SUPPORT DRAWING STEEL AND PIPE MATERIAL
FOR STEEL MEMBER CODE AND (INSULATION, U-BOLTS,
WELDING FILLET SIZE, SEE HANGERS, ETC)
STEEL CODE MAXIMUM MAXIMUM LOAD

NUMBER SPAN "L" PER LEVEL (kN)
4 1520 8.9
8 1520 22.2
NOTES:
WHERE GUIDES, ANCHORS, OR DIRECTIONAL ANCHORS ARE USED IN CONJUNCTION
3. THIS SUPPORT IS FOR A MAXIMUM OF THREE LEVELS ONLY.
4. DESIGNER SHALL PROVIDE DIMENSION "A" FOR ONE PIPE ONLY.
SUPPORT ATTACHEMENT
TAG TYPE / MATERIAL
705B BOLTED / C.S.
705W WELDED / C.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
J.M.D./T.G.
DATE
0 T.G.
EXTRA STEEL
03/28/95

H.LESKIE
10/22/04
2 D.K.
11/21/05
T.O.S. ELEV.
SPEC. ON PLAN
"A"
AS SPEC. ON DWG.
SPACER BLOCK USE 5/8" dia. A325 BOLTS
IF REQUIRED C/W NUTS & LOCK WASHERS
"L"


8 1830 22.2
9 3050 31.1
NOTES:
FOR ONLY ONE PIPE.
SUPPORT ATTACHEMENT
TAG TYPE / MATERIAL
706B BOLTED / C.S.
706W WELDED / C.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-X700,
J.M.D./T.G.
DATE
0 T.G.
EXTRA STEEL
03/28/95

H.LESKIE
10/22/04
DATE 03/28/95 DS-PS-X706 1

T.O.S. ELEV.
SPEC. ON PLAN

USE 5/8" dia. A325 BOLTS
SPACER BLOCK
IF REQUIRED
"A" 75mm MIN.
"B" "L"

STEEL CODE MAXIMUM MINIMUM MAXIMUM

NUMBER SPAN "A" SPAN "L" LOAD (kN)
8 610 3 x "A" 22.2
9 610 3 x "A" 31.1
NOTES:
SUPPORT ATTACHEMENT
TAG TYPE / MATERIAL
707B BOLTED / C.S.
707W WELDED / C.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-X700,
J.M.D./T.G.
DATE
0 T.G.
EXTRA STEEL
03/28/95

H.LESKIE
10/22/04
2 D.K.
11/18/05
DIMENSIONS RE-LABELLED B.C. DATE 03/28/95 DS-PS-X707 2
"A" "L" 610 MAX.
1220 MAX. SEE SUPPORT DWG
T.O.S. ELEV.
SPEC. ON PLAN
6mm STOP PLATE
45^ WHERE
POSSIBLE EXTRA STEEL MEMBER SPECIFIED
75
MIN.
WT 75 x 11
STEEL CODE MAXIMUM

NUMBER LOAD (kN)
8 22.2
9 31.1
NOTES:
2. FOR VERTICAL LOADS GREATER THAN THOSE LISTED, STEEL SIZE SELECTION
SUPPORT EXTRA STEEL

TAG MATERIAL
708 C.S.
708S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-X700
J.M.D./T.G.
DATE
0 T.G.
EXTRA STEEL
03/28/95

H.LESKIE
10/22/04
2 D.K.
11/18/05
WT75 x 11
45^ WHERE EXTRA STEEL MEMBER SPECIFIED

POSSIBLE ON PIPE SUPPORT DRAWING
B.O.S. ELEV.
SPEC. ON PLAN
1220 MAX. 75
"L"
STEEL CODE MAXIMUM

NUMBER LOAD (kN)
8 22.2
9 31.1
NOTES:
SUPPORT EXTRA STEEL

TAG MATERIAL
709 C.S.
709S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-X700
J.M.D./T.G.
DATE
0 T.G.
EXTRA STEEL
03/28/95

H.LESKIE
10/22/04
2 D.K.
11/18/05
SUPPORT STEEL
WELDED ATTACHMENT
ANVIL INTL. FIG. 66
OR EQUAL
"L"
WELDLESS EYE NUT
ANVIL INTL. FIG. 290 "A"
OR EQUAL
AS SPEC.
ON DWG.
HANGER ROD C/W LOCK SEE NOTE 3
NUTS
100 MIN.
"B"
T.O.S. ELEV.
SPEC. ON PLAN

STEEL CODE MAXIMUM MAXIMUM MAXIMUM

NUMBER SPAN "L" SPAN "B" LOAD (kN)
4 1520 1/3 x "L" 8.9
8 1520 1/3 x "L" 22.2
NOTES:
GUIDES, ANCHORS, AND DIRECTIONAL ANCHORS ARE NOT TO BE USED IN
CONJUNCTION WITH THIS DETAIL.
2. FOR SPANS OR VERTICAL LOADS GREATER THAN THOSE LISTED, STEEL SIZE
SELECTION SHALL BE APPROVED BY THE STRUCTURAL ENGINEER.
FOR ONLY ONE PIPE.
SUPPORT EXTRA STEEL

TAG MATERIAL
710 C.S.
710S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-110, DS-PS-112 DS-PS-X700
J.M.D./T.G.
DATE
0 T.G.
03/28/95
ISS’D FOR CONSTRUCTION H.L. CH. Y.T. EXTRA STEEL
1 Y.T. SUP. H.LESKIE
2 D.K.
11/18/05
"D"
MIN.
PIPE SHOE IF APPLICABLE

38
TYP. 12mm THK PLATE
"D"
TOP PLATE PER DETAIL
"HEIGHT" AS SPEC. ON DWG.

7
1220 MAX.
STEEL SIZE PER TABLE

STANDARD DS-PS-X756
7 IF SPECIFIED ON DRAWING
GROUT
CONCRETE PEDESTAL
WHERE APPLICABLE
PIPE DIA. STEEL BASE TOP PLATE

"D" SIZE PLATE DIM. "D"
3" - 6" W100 x 19.3 TYPE 1 150
8" - 12" W150 x 22.5 TYPE 1 200
14" - 18" W200 x 46.1 TYPE 2 255
20" - 24" W250 x 73 TYPE 2 305
NOTES:
1. THIS SUPPORT IS DESIGNED FOR VERTICAL LOADING ONLY. GUIDES, ANCHORS,
AND DIRECTIONAL ANCHORS ARE NOT TO BE USED IN CONJUNCTION WITH
THIS DETAIL WITHOUT THE APPROVAL OF THE STRUCTURAL ENGINEER.
SUPPORT EXTRA STEEL

TAG MATERIAL
713 C.S.
713S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-X756
J.M.D./T.G.
DATE
0 T.G.
EXTRA STEEL
03/28/95

H.LESKIE
10/22/04
2 D.K.
11/18/05
"W" SPEC. ON DWG.
125 MIN.
PIPE SHOE IF APPLICABLE

38
TYP. 12mm THK PLATE
125
TOP PLATE PER DETAIL
"HEIGHT" AS SPEC. ON DWG.

7
915 MAX.
STEEL SIZE PER TABLE

STANDARD DS-PS-X756
7 IF SPECIFIED ON DRAWING
GROUT
CONCRETE PEDESTAL
WHERE APPLICABLE
DIAMETER OF STEEL BASE MAX. HORIZ.

SUPPORTED PIPE SIZE PLATE LOAD (kN)
3" - 6" HSS 127 x 127 x 6.4 TYPE 1 8.9
8" - 12" HSS 127 x 127 x 6.4 TYPE 1 8.9
NOTES:
1. THIS SUPPORT IS DESIGNED FOR MAXIMUM HORIZONTAL LOADS INDICATED ONLY.
2. MAXIMUM LATERAL PIPE MOVEMENT IS 75mm AT SUPPORT POINT.
3. FOR LOADS, HEIGHTS, AND PIPE SIZES GREATER THAN THOSE LISTED, DESIGN
SUPPORT EXTRA STEEL

TAG MATERIAL
716 C.S.
716S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-X756
J.M.D./T.G.
DATE
0 T.G.
EXTRA STEEL
03/28/95

H.LESKIE
10/22/04
2 D.K.
11/21/05
"A" "L" 610 MAX.
1220 MAX. SEE SUPPORT DWG
T.O.S. ELEV.
SPEC. ON PLAN
6mm STOP PLATE
45^ WHERE
POSSIBLE
75 IF APPLICABLE
MIN.
WT75 x 11
((4) 3/4 " DIA. x 9" LONG HILTI

12mm PLATE
IF ATTACHED TO CONCRETE,
SEE NOTES 3 & 4
50
OR (4) 3/4 " DIA. A325 BOLTS
IF ATTACHED TO STRUCTURAL
STEEL. HOLE SIZE TO SUIT
MAX
38
STEEL CODE MAXIMUM
NUMBER LOAD (kN)
TO SUIT
8 22.2
9 31.1
FOR TANK
MTG. ONLY 5
NOTES:
1. MAXIMUM SPANS AND LOADS INDICATED REPRESENT VERTICAL
LOADING ONLY, WHERE ANCHORS, OR DIRECTIONAL ANCHORS ARE
USED IN CONJUNCTION WITH THIS DETAIL, STEEL SIZE SELECTION
2. FOR VERTICAL LOADS GREATER THAN THOSE LISTED, STEEL SIZE
50
3. FOR TANK MOUNTING, PLATE MATERIAL AND THICKNESS SHALL 38 38
MATCH TANK WALL; SHAPE TO SUIT.
4. TANK VENDOR MUST BE NOTIFIED OF ANTICIPATED LOADING ON TANK. 200
SUPPORT EXTRA STEEL

TAG MATERIAL
750 C.S.
750S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-X700
J.M.D./T.G.
DATE
0 T.G.
EXTRA STEEL
03/28/95

SUP. H.LESKIE
4 D.K.
11/21/05
12mm PLATE
SEE NOTES 3 & 4
WT 75x11
45^ WHERE
POSSIBLE
B.O.S. ELEV.
50
SPEC. ON PLAN
1220 MAX. 75 ((4) 3/4 " DIA. x 9" LONG HILTI
MAX.
38
"L" HIT HY 150 ADHESIVE ANCHORS
OR (4) 3/4 " DIA. A325 BOLTS
TO SUIT
FOR TANK
MTG. ONLY 5
STEEL CODE MAXIMUM
MAX.
NUMBER LOAD (kN) EXTRA STEEL MEMBER SPECIFIED
38
8 22.2 ON PIPE SUPPORT DRAWING
9 31.1
50
NOTES:
38 38
1. MAXIMUM SPANS AND LOADS INDICATED REPRESENT VERTICAL
LOADING ONLY, WHERE ANCHORS, OR DIRECTIONAL ANCHORS ARE
200
USED IN CONJUNCTION WITH THIS DETAIL, STEEL SIZE SELECTION
2. FOR VERTICAL LOADS GREATER THAN THOSE LISTED, STEEL SIZE
3. FOR TANK MOUNTING, PLATE MATERIAL AND THICKNESS SHALL
4. TANK VENDOR MUST BE NOTIFIED OF ANTICIPATED LOADING ON TANK.
SUPPORT EXTRA STEEL

TAG MATERIAL
751 C.S.
751S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-X700
J.M.D./T.G.
DATE
0 T.G.
EXTRA STEEL
03/28/95

SUP. H.LESKIE
3 D.K.
11/21/05
"L" "A" 455 MAX. FOR STEEL MEMBER CODE AND
SEE TABLE SEE SUPPORT WELDING FILLET SIZE, SEE

DWG
200
38 38
50
T.O.S. ELEV.
SPEC. ON
PLAN
MIN.
255
6mm STOP
PLATE
FOR TANK
50
MTG. ONLY 5
12mm PLATE
SEE NOTES 3 & 4
((4) 3/4 " DIA. x 9" LONG HILTI
OR (4) 3/4 " DIA. A325 BOLTS

NUMBER LOAD (kN) "A"
8 11.1 455
8 4.4 760
8 2.2 1060
NOTES:
SUPPORT EXTRA STEEL

TAG MATERIAL
753 C.S.
753S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-X700
J.M.D./T.G.
DATE
0 T.G.
EXTRA STEEL
03/28/95

SUP. H.LESKIE
4 D.K.
11/21/05
"L"
SEE TABLE
200
38 38
50
T.O.S. ELEV.
SPEC. ON PLAN
MIN.
255
FOR TANK
MTG. ONLY 5
50
12mm PLATE OR (4) 3/4 " DIA. A325 BOLTS
75
SEE NOTES IF ATTACHED TO STRUCTURAL
3 & 4 STEEL. HOLE SIZE TO SUIT

NUMBER LOAD (kN) "L"
8 11.1 455
8 4.4 760
8 2.2 1060
NOTES:

SUPPORT EXTRA STEEL

TAG MATERIAL
754 C.S.
754S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-X700
J.M.D./T.G.
DATE
0 T.G.
EXTRA STEEL
03/28/95

SUP. H.LESKIE
3 D.K.
11/21/05
STEEL "S"
"L"
AS SPEC. ON DWG.
SPEC. ON DWG
T.O.S. ELEV. "A"
25
SPEC. ON DWG 5
SUPPORT PLATE
ON DRAWING 6mm STOP PLATE
SPECIFIED
7
STD. WT. PIPE
"H"
NOM. SIZE "C"
6mm dia. VENT HOLE

7 STANDARD DS-PS-X756
GROUT OR CONCRETE
PEDESTAL IF APPLICABLE
"C"
STEEL SUPPORT MAXIMUM MAXIMUM MAXIMUM BASE
AS SPEC.
"S" PLATE HEIGHT "H" LENGTH "L" LOAD (kN) PLATE
ON DWG
3" C100 x 11 125 x 125 x 10 915 455 9.8 TYPE 1
4" W100 x 19 150 x 150 x 10 1220 610 7.1 TYPE 1
6" W100 x 19 200 x 200 x 10 1830 760 9.8 TYPE 2
8" W150 x 22 255 x 255 x 10 2430 915 8.0 TYPE 2
10" W200 x 36 305 x 305 x 10 3050 1220 5.7 TYPE 2
NOTES:
1. MAXIMUM DIMENSIONS AND LOADS INDICATED REPRESENT VERTICAL LOADING ONLY,
WITH THIS DETAIL, DESIGN SHALL BE APPROVED BY THE STRUCTURAL ENGINEER.
2. FOR DIMENSIONS OR VERTICAL LOADS GREATER THAN THOSE LISTED, DESIGN SHALL BE
APPROVED BY THE STRUCTURAL ENGINEER.
FOR ONLY ONE PIPE.
SUPPORT EXTRA STEEL

TAG MATERIAL
755 C.S.
755S 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS
DS-PS-X756
J.M.D./T.G.
DATE
0 T.G.
EXTRA STEEL
03/28/95

H.LESKIE
10/22/04
DATE 03/28/95 DS-PS-X755 1

GROUT PLATE AFTER LEVELLING
GROUT
MAX.
50
BASE PLATE
ENTIRE PAD AREA

TO BE ROUGHENED
3/4 " DIA. x 11" LONG HILTI HIT HY 150
ADHESIVE ANCHORS WITH LEVELING NUTS
SLAB-MOUNTED PLATE
115
MIN.
LEVELLING
GROUT
MAX.
BASE PLATE NUT
38
SUIT
CONC. PAD
TO
BY OTHERS
3/4 " DIA. x 11" LONG HILTI HIT HY 150

ADHESIVE ANCHORS WITH LEVELING NUTS
PAD-MOUNTED PLATE
305 SQ. 405 SQ.
38 38
TYP. TYP.
(4) 25 dia. (6) 25 dia.
HOLES HOLES
SUPPORT BASE PLATE /

TAG MATERIAL
TYPE 1 TYPE 2 756A TYPE 1 / C.S.
20mm THK 20mm THK 756B TYPE 2 / C.S.
756AS TYPE 1 / 316 S.S.
756BS TYPE 2 / 316 S.S.
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS

J.M.D./T.G.
DATE
0 T.G. ISS’D FOR CONSTRUCTION H.L. CH. Y.T. EXTRA STEEL- ANCHOR BASE PLATE
03/28/95
1 T.G. PLT. THICKNESS REV’D. J.Z. SUP. DESIGN STANDARD NO. REV.
H.LESKIE
03/19/96
2 T.G.
10/22/04
HILTI ANCHOR TYPE CHG’D DATE 03/28/95 DS-PS-X756 2
GROUT PAD AFTER LEVELLING
50 MAX
GROUT
12mm
WEAR PLATE
GRIND
SMOOTH
ENTIRE PAD AREA

TO BE ROUGHENED
DRILL AND GROUT IN
5/8" dia. THREADED RODS
SLAB-MOUNTED PLATE
LEVELLING
NUT
FULL THREADED
NOTE: RODS SAME MATERIAL
AFTER POSITIONING & LEVELLING OF AS BASE PLATE
WEAR PLATE, BOLTS SHALL BE CUT
TO 6mm BELOW T.O. PLATE & PLUG
WELDED BEFORE GROUTING PAD.
GRIND FLUSH WITH PLATE SURFACE
305 SQ. 405 SQ.
75 100
TYP. TYP.
=
(2) 20mm dia. HOLES

=
(4) 20mm dia. HOLES
TYPE 1 TYPE 2
500 SQ. SUPPORT BASE PLATE /

TAG MATERIAL
100
TYP. 757A TYPE 1 / C.S.
757B TYPE 2 / C.S.
757C TYPE 3 / C.S.
757AS TYPE 1 / 316 S.S.

(4) 20mm dia. HOLES
757BS TYPE 2 / 316 S.S.
757CS TYPE 3 / 316 S.S.
TYPE 3
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS

J.M.D./T.G.
DATE
0 T.G. ISS’D FOR CONSTRUCTION H.L. CH. Y.T.

EXTRA STEEL- WEAR PLATE
03/28/95
1 T.G. DESIGNATION REV’D. SUP. DESIGN STANDARD NO. REV.

H.LESKIE
10/22/04
DATE 03/28/95 DS-PS-X757 1

1. GENERAL
THE SYMBOLS TO BE USED AT THE PIPE SHALL INDICATE ONE OF THE FOLLOWING
TYPE OF SUPPORT:
DESIGN
STANDARD No.s
PIPE ANCHOR "A" FOR ANCHOR 200 - 249
DIRECTIONAL ANCHOR "DA" FOR DIRECTIONAL ANCHOR 250 - 299
PIPE GUIDE "G" FOR GUIDE 300 - 399
PIPE SUPPORT "H" FOR HANGER 400 - 499

"S" FOR SUPPORT 600 - 699
"X" FOR EXTRA STEEL 700 - 799
2. SUPPORT IDENTIFICATION SYMBOLS
EACH PIPE SUPPORT SHALL BE IDENTIFIED ON THE PIPING ISOMETRIC BY ONE

OR MORE FRAMES CONTAINING THE SUPPORT DESIGNATION. THE FRAMES
SHALL BE CONNECTED TO A SUPPORT SYMBOL WITH A LEADER LINE,
WITH ITS ARROW POINTING TO THE SUPPORT LOCATION.
3. SUPPORT DESIGNATION
3.1 GENERAL
GENERALLY, ONE FRAME WILL BE USED TO IDENTIFY THE METHOD OF SUPPORT.

THE FRAME SHALL BE DIVIDED IN 2 SECTIONS. THE TOP SECTION CORRESPONDS
TO THE SUPPORT NUMBER ON THE ISOMETRIC. THE BOTTOM SECTION CORRESPONDS
TO THE SUPPORT DESIGN STANDARD NUMBER OR SPECIAL SUPPORT DETAIL NUMBER.
PS# WHERE "#" DENOTES THE PIPE SUPPORT

PS#
NUMBER ON THE ISOMETRIC.
eg. PS1, PS2, ETC.
PS-S605 SHOE ASSEMBLY,

PS-S605
DS-PS-S605
DESIGN STANDARD
PIPE SUPPORT
REF. STANDARDS

J.M.D./T.G.
DATE
03/28/95
H.LESKIE
12/01/97
DATE 03/28/95 DS-PS-100 1


Pipe Support Fluor PDF Free

Uploaded by

Copyright:

Available Formats

Pipe Support Fluor PDF Free

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Pipe Support Fluor PDF Free

Uploaded by

Copyright:

Available Formats

What are the different types of pipe supports described?

What are the different types of pipe supports described?

What information is included on pipe support identification frames?

What information is included on pipe support identification frames?

MIN.

SUPPORT COMPONENT SUPPORT COMPONENT SEE NOTE 1

20mm THK. PLATE 20mm THK. PLATE

TWO-BOLT CONCRETE HANGER PLATE TWO-BOLT STEEL HANGER PLATE

20mm THK. PLATE 20mm THK. PLATE

FOUR-BOLT CONCRETE HANGER PLATE FOUR-BOLT STEEL HANGER PLATE

26.6 kN MAX. LOAD 26.6 kN MAX. LOAD

1. WHEN ATTACHED TO UNDERSIDE OF AN EXISTING W SHAPE, SPACING BETWEEN BOLTS

SUPPORT HANGER PLATE /

758A TWO-BOLT / C.S.

758B FOUR-BOLT / C.S.

758AS TWO-BOLT / 316 S.S.

758BS FOUR-BOLT / 316 S.S.

REV. BY REVISION APP. DES. DESIGNATION

0 T.G. ISS’D FOR CONSTRUCTION H.L. CH. Y.T.

1 T.G. REF. STANDARDS ADDED DESIGN STANDARD NO. REV.

DATE 03/28/95 DS-PS-X758 1

PS# WHERE "#" DENOTES THE PIPE SUPPORT

L DIMENSION "L" AS SPEC.

3.2 MULTIPLE COMPONENT SUPPORTS

PS5 FIFTH PIPE SUPPORT

PS6 SIXTH PIPE SUPPORT

PS-DA251 DIRECTIONAL ANCHOR,

REV. BY REVISION APP. DES. DESIGNATION

PIPE SUPPORT ASSEMBLIES INCORPORATING EXTRA STEEL ARRANGEMENTS OF THE

X755 EXTRA STEEL,

A, L DIMENSION "A" AND "L" AS SPEC.

X702B-9 EXTRA STEEL,

"9" FOR STEEL CODE NUMBER 9

A, L DIMENSION "A" AND "L" AS SPEC.

3.4 MULTIPLE PIPE SUPPORTS

REV. BY REVISION APP. DES. DESIGNATION

DATE 03/28/95 DS-PS-102 1

PS-X703 EXTRA STEEL,

ISOMETRIC FOR ALL OTHER PIPES:

PS-X703 (REF) REFERENCE TO

3.5 SPECIAL SUPPORT DETAILS

SPECIAL PIPE SUPPORTS THAT DO NOT CONSIST OF ELEMENTS CONTAINED IN THE

SD-100 UNIQUE ITEM

SUPPORTS CONSISTING OF COMBINATIONS OF STANDARD TYPES AND SPECIAL DETAILS

AN EXCEPTION TO THE ABOVE IS MULTIPLE PIPE SUPPORT CASES SIMILAR TO 3.3

REV. BY REVISION APP. DES. DESIGNATION

MAXIMUM SAFE LOADS, (kN)

2. HANGER RODS 1 3/4" dia. AND LARGER SHALL BE SHOP THREADED.

4. TEMPERATURE OF HANGER ROD SHALL BE BASED ON A TEMPERATURE GRADIENT OF

REV. BY REVISION APP. DES. DESIGNATION

DATE 03/28/95 DS-PS-113 1

WHICH ARE TO BE FOUND IN THEIR PERTINENT DESIGN STANDARDS.

1. CLAMP SHALL MATCH THE OUTSIDE DIAMETER OF PIPE AS SPECIFIED IN PIPING

3. HANGER ROD DIAMETER IF NOT SPECIFIED WITH PIPE SUPPORT SELECTION

4. HANGER RODS 1 3/4" DIA. AND LARGER SHALL BE SHOP THREADED.

6. TEMPERATURE OF HANGER ROD SHALL BE BASED ON A TEMPERATURE GRADIENT

8. RISER CLAMPS PER DS-PS-123 AND 124 SHALL BE USED AS FOLLOWS:

9. VERTICAL STAINLESS STEEL PIPE LINES REQUIRING RISER CLAMP SUPPORTS

ANVIL INTL. FIG. 212, FIG. 216 & FIG. HS-42SD.