Department of Information Science and Engineering Analog and Digital Electronics Lab Subject Code: 17Csl37 Lab Manual

DEPARTMENT OF INFORMATION
SCIENCE AND ENGINEERING
ANALOG AND DIGITAL ELECTRONICS LAB

SUBJECT CODE: 17CSL37
LAB MANUAL
FACULTY: MRS.DEEPTI C
PESIT – BANGALORE SOUTH CAMPUS
1Km before Electronics City, Hosur Road,

Bangalore-560100.
Analog and Digital Electronics Laboratory 17CSL37
ANALOG AND DIGITAL ELECTRONICS LABORATORY

[As per Choice Based Credit System (CBCS) scheme]
(Effective from the academic year 2017 -2018)
SEMESTER - III
Laboratory Code 17CSL37 IA Marks 40
Number of Lecture Hours/Week 01I + 02P Exam Marks 60
Total Number of Lecture Hours 40 Exam Hours 03
CREDITS – 02
Course objectives:
This laboratory course enable students to get practical experience in design,
assembly and evaluation/testing of
· Analog components and circuits including Operational Amplifier, Timer, etc.
· Combinational logic circuits.
· Flip - Flops and their operations
· Counters and registers using flip-flops.
· Synchronous and Asynchronous sequential circuits.
· A/D and D/A converters
Descriptions (if any)

Any simulation package like MultiSim / P-spice /Equivalent software may be used.
Faculty-in-charge should demonstrate and explain the required hardware components and
their functional Block diagrams, timing diagrams etc.
Students have to prepare a write-up on the same and include it in the Lab record and to be
evaluated.
Laboratory Session-1: Write-up on analog components; functional block diagram, Pin
diagram (if any), waveforms and description. The same information is also taught in theory
class; this helps the students to understand better.
Laboratory Session-2: Write-upon Logic design components, pin diagram (if any), Timing
diagrams, etc. The same information is also taught in theory class; this helps the students to
understand better.
Note: These TWO Laboratory sessions are used to fill the gap between theory classes and
practical sessions. Both sessions are to be evaluated for 40 marks as lab experiments.
2
Department of ISE PESIT-BSC
Laboratory Experiments:
1. a) Design and construct a Schmitt trigger using Op-Amp for given UTP and LTP values
and demonstrate its working.
b) Design and implement a Schmitt trigger using Op-Amp using a simulation package for
two sets of UTP and LTP values and demonstrate its working.
2. a) Design and construct a rectangular waveform generator (Op-Amp relaxation
oscillator) for given frequency and demonstrate its working.
b) Design and implement a rectangular waveform generator (Op-Amp relaxation
oscillator) using a simulation package and demonstrate the change in frequency when
all resistor values are doubled.
3. Design and implement an Astable multivibrator circuit using 555 timer for a given
frequency and duty cycle.
NOTE: hardware and software results need to be compared
4. Design and implement Half adder, Full Adder, Half Subtractor, Full Subtractor using
basic gates.
5. a) Given a 4-variable logic expression, simplify it using Entered Variable Map and
realize the simplified logic expression using 8:1 multiplexer IC.
b) Design and develop the Verilog /VHDL code for an 8:1 multiplexer. Simulate and
verify its working.
6. a) Design and implement code converter I)Binary to Gray (II) Gray to Binary Code using
basic gates.
7. Design and verify the Truth Table of 3-bit Parity Generator and 4-bit Parity
Checker using basic Logic Gates with an even parity bit.
8. a) Realize a J-K Master / Slave Flip-Flop using NAND gates and verify its truth
table.
b) Design and develop the Verilog / VHDL code for D Flip-Flop with positive-edge
triggering. Simulate and verify it’s working.
9. a) Design and implement a mod-n (n<8) synchronous up counter using J-K Flip-
Flop ICs and demonstrate its working.
b) Design and develop the Verilog / VHDL code for mod-8 up counter. Simulate and
verify its working.
3
10. Design and implement an asynchronous counter using decade counter IC to

count up from 0 to n (n<=9) and demonstrate on 7-segment display (using IC- 7447).
11. Generate a Ramp output waveform using DAC0800 (Inputs are given to DAC
through IC74393 dual 4-bit binary counter).
Study experiment
12. To study 4-bitALU using IC-74181.
Course outcomes:
On the completion of this laboratory course, the students will be able to:
· Use various Electronic Devices like Cathode ray Oscilloscope, Signal generators, Digital
Trainer Kit, Multimeters and components like Resistors, Capacitors, Op amp and
Integrated Circuit.
· Design and demonstrate various combinational logic circuits.
· Design and demonstrate various types of counters and Registers using Flip-flops
· Use simulation package to design circuits.
· Understand the working and implementation of ALU.
Conduction of Practical Examination:
1 . All laboratory experiments (1 to 11 nos) are to be included for practical examination.
2 . Students are allowed to pick one experiment from the lot.
3 . Strictly follow the instructions as printed on the cover page of answer script.
4 . Marks distribution:
a ) For questions having part a only- Procedure + Conduction + Viva:15 + 70 +15=100 Marks
b ) For questions having part a and b
Part a- Procedure + Conduction + Viva:09 + 42 +09= 60 Marks
Part b- Procedure + Conduction + Viva:06 + 28 +06= 40 Marks
5 . Change of experiment is allowed only once and marks allotted to the procedure
part to be made zero.
4
ADE LAB
DO’S AND DON’TS
DOs DON’TS
Be regular to the Lab Do not come late to the Lab
Follow proper Dress Code Do not throw connecting wires on the
Floor
Wear your College ID card Do not operate the IC trainer kits without
permission
Avoid unnecessary talking while doing the Avoid loose connection and short circuits
experiment
Take the signature of the lab in charge before Do not interchange the ICs while doing
taking the components the experiment
Handle the trainer kit properly Do not panic if you do not get the output
Keep your work area clean after completing the
experiment.
After completion of the experiment switch off
the power and return the components
Arrange your chairs and tables before leaving
the laboratory.
RULES AND REGULATIONS
Lab Teams: Lab teams consisting of three or four students will be formed during the first lab
session. It is expected that all team members will contribute to all the lab work.
Laboratory Preparation: Each student is responsible for maintaining his/her own
Laboratory Observation Notebook. Each student is required to perform pre-lab work and
enter it into his/her observation notebook.
Lab Work: Each lab team must enter the components taken for the experiment into the
checkout register with the lab instructor. Check-out will be used to confirm that the actual lab
work as recorded in the lab notebook has been completed and that the lab station has been
properly cleaned up. The faculty will initial and date all the data acquired during the lab
period. All pages will be signed by the allotted faculty on the same date in the lab itself.
Lab Completion: Each experiment should be completed during the lab period. If a group is
unable to complete the lab work, they may complete it in the Break time, if granted
permission by the instructor. The work must be checked to verify that all laboratory exercises
are complete.
In case a student is ABSENT for a particular lab session, he/she has to compulsorily finish
the experiment before the next lab session and get the observation signed . All lab work
should be completed before the next laboratory period.
5
Lab Grading
The faculty will examine your notebooks during lab period and assign a grade based upon the
quality and contents of your work.
There will be eleven lab experiments and a one internal lab test of 80 marks (Reduced to 20).
Each lab experiment is worth up to 20 points. Each lab contains two parts as follows.
1. Observation (10 marks per lab): Each student should read the lab material and
finish the observation before the lab. Observation should be completed before the
beginning of each lab session. Late observations will not be accepted.
2. Lab record (10 marks per lab): Students will write a lab record according to the
format specified and turn it in at the beginning of the next lab session. Late lab reports
will not be accepted.
At the end of the semester all notebooks will be collected for a final grade by the faculty.
Penalty for incomplete work: If any of the 2 parts is missed, a score of zero will be reported
by the faculty for that lab.
10 Marks will be deducted from the record for the particular experiment if the student
is absent for the lab.
10 Marks will be deducted from the observation for the particular experiment if the
student is absent for the tutorial.
6
Rules for Maintaining Laboratory Record
1. Put your name, USN and subject on the outside front cover of the record. Put that
same information on the first page inside.
2. Update Table of Contents every time you start each new experiment or topic
3. Always use black pen and write neatly and clearly
4. Start each new topic (experiment, notes, calculation, etc.) on a right-side (odd
numbered) page
5. Obvious care should be taken to make it readable, even if you have bad handwriting
6. Date to be written every page on the top right side corner
7. On each right side page
Title of experiment
Aim/Objectives
Components Required
Theory
Procedure described clearly in steps
Result
8. On each left side page
Pin diagrams
Circuit diagram
Tables
Graphs
Use labels and captions for figures and tables
9. Do not use jargon. Avoid the use of slang or obscure language.
10. Use the correct (i.e., IEEE standard) abbreviations for all units.
11. Attach printouts and plots of data as needed. Stick printouts(A4 Size)on the right side
of the lab record
12. All pages signed by the allotted faculty before the next lab session
13. Strictly observe the instructions given by the Teacher/ Lab Instructor.
7
Rules for Maintaining Observation Book
1. Put your name, USN and subject on the outside front cover of the record. Put that same
information on the first page inside.
2. Start each new topic (experiment, notes, calculation, etc.) on a right-side (odd
numbered) page
3. Obvious care should be taken to make it readable, even if you have bad handwriting
4. Date to be written every page on the top right side corner
5. Observation Notebook Format
Cover: "17CSL37"
“Analog and Digital Electronics Laboratory”
"Observation book",
Your name
Semester
USN, Lab Batch and Group Number
Year
1st page: Table of Contents -- Experiment #, Title, Date
2nd page:
6. Pre-Lab Work for each experiment
On each right side page
Title of experiment, Date
Aim/Objectives
Equipment required
Completed Theoretical Data
Result
7. On each left side page
8. Pin diagrams (Write captions for all figures and tables)
Circuit diagram
Tables
8
OBSERVATION BOOK CONTENTS

Sl. Exp Date Title of the Marks(5) Page Faculty
No No Experiment No Sign
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
9
INTRODUCTION TO ADE LAB
ELECTRONIC COMPONENTS
1. RESISTORS
A resistor is a component of an electrical circuit that resists the flow of electrical current. A
resistor has two terminals across which electricity must pass, and is designed to drop the
voltage of the current as it flows from one terminal to the next. A resistor is primarily used to
create and maintain a known safe current within an electrical component.
Resistance is measured in ohms, after Ohm's law. A 1000 Ohm resistor is typically shown as
1K-Ohm (kilo Ohm), and 1000 K-Ohms is written as 1M-Ohm (mega ohm).
Resistor Colour Code:
2. Capacitors
The capacitor's capacitance (C) is a measure of the amount of charge (Q) stored on each plate
for a given potential difference or voltage (V) which appears across the plates. In SI units, a
capacitor has a capacitance is measured in farad (F).
10
Picofarad Nanofarad Microfarad Picofarad Nanofarad Microfarad

Code Code
(pF) (nF) (uF) (pF) (nF) (uF)
10 0.01 0.00001 100 4700 4.7 0.0047 472
15 0.015 0.000015 150 5000 5.0 0.005 502
22 0.022 0.000022 220 5600 5.6 0.0056 562
33 0.033 0.000033 330 6800 6.8 0.0068 682
47 0.047 0.000047 470 10000 10 0.01 103
100 0.1 0.0001 101 15000 15 0.015 153
120 0.12 0.00012 121 22000 22 0.022 223
130 0.13 0.00013 131 33000 33 0.033 333
150 0.15 0.00015 151 47000 47 0.047 473
180 0.18 0.00018 181 68000 68 0.068 683
220 0.22 0.00022 221 100000 100 0.1 104
330 0.33 0.00033 331 150000 150 0.15 154
470 0.47 0.00047 471 200000 200 0.2 254
560 0.56 0.00056 561 220000 220 0.22 224
680 0.68 0.00068 681 330000 330 0.33 334
750 0.75 0.00075 751 470000 470 0.47 474
820 0.82 0.00082 821 680000 680 0.68 684
1000 1.0 0.001 102 1000000 1000 1.0 105
1500 1.5 0.0015 152 1500000 1500 1.5 155
2000 2.0 0.002 202 2000000 2000 2.0 205
2200 2.2 0.0022 222 2200000 2200 2.2 225
3300 3.3 0.0033 332 3300000 3300 3.3 335
3. Breadboard
A breadboard is a material or a device used to build a prototype of an electronic circuit.
The breadboard has many strips of metal (copper usually) which run underneath the board.
The metal strips are laid out as shown These strips connect the holes on the top of the board.
This makes it easy to connect components together to build circuits. To use the bread board,
the legs of components are placed in the holes (the sockets). The holes are made so that they
will hold the component in place. Each hole is connected to one of the metal strips running
underneath the board. The long top and bottom row of holes are usually used for power
supply connections.
11
4. Power Supply
A power supply is a separate unit or part of a circuit that supplies power to the rest of the
circuit or to a system. The power supply takes the current from your wall electrical socket
and converts it into the various voltages your circuit needs.
5. Multimeter
A meter is a measuring instrument. An ammeter measures current, a voltmeter measures the
potential difference (voltage) between two points, and an ohmmeter measures resistance. A
multimeter combines these functions and possibly some additional ones as well, into a single
instrument.
6. Signal/Function Generator
A function generator is a device that can produce various patterns of voltage at a variety of
frequencies and amplitudes. It is used to test the response of circuits to common input signals.
The electrical leads from the device are attached to the ground and signal input terminals of
the device under test.
Most function generators allow the user to choose the shape of the output from a small
number of options.
• Square wave - The signal goes directly from high to low voltage.
• Sine wave - The signal curves like a sinusoid from high to low voltage.
• Triangle wave - The signal goes from high to low voltage at a fixed rate.
The amplitude control on a function generator varies the voltage difference between the high
and low voltage of the output signal. The frequency control of a function generator controls
the rate at which output signal oscillates.
Most function generators allow the user to choose the shape of the output from a small
number of options.
• Square wave - The signal goes directly from high to low voltage.
• Sine wave - The signal curves like a sinusoid
from high to low voltage.
• Triangle wave - The signal goes from high to
low voltage at a fixed rate.
12
The amplitude control on a function generator varies the voltage difference between the high
and low voltage of the output signal. The frequency control of a function generator controls
the rate at which output signal oscillates.
Switch on the function generator and adjust the output level to produce a visible signal on the
oscilloscope screen. Adjust TIME/DIV and VOLTS/DIV to obtain a clear display and
investigate the effects of pressing the waveform shape buttons.
The rotating FREQUENCY control and the RANGE switch are used together to determine
the frequency of the output signal.
7. Oscilloscope
An oscilloscope is easily the most useful instrument available for testing circuits because it
allows you to see the signals at different points in the circuit. The best way of investigating an
electronic system is to monitor signals at the input and output of each system block, checking
that each block is operating as expected and is correctly linked to the next.
The screen of this oscilloscope has 8 squares or

divisions on the vertical axis, and 10 squares or divisions on the horizontal axis. Usually,
these squares are 1 cm in each direction:
13
Setting up the CRO
i. Before you switch the oscilloscope on, check that all the controls are in their
'normal' positions.
a) all push button switches are in the OUT position

b) all slide switches are in the UP position
c) all rotating controls are CENTRED
ii. Check through all the controls and put them in these positions:
iii. Set both VOLTS/DIV controls to 1 V/DIV and the TIME/DIV control to 2 s/DIV,
its slowest setting:
VOLTS/DIV TIME/DIV
iv. Switch ON, red button, top center:
The green LED illuminates and, after a few moments, you should see a small bright spot, or
trace, moving fairly slowly across the screen.
v. Find the Y-POS 1 control:
The Y-POS 1 allows you to move the spot up and down the screen. For the present, adjust the
trace so that it runs horizontally across the center of the screen.
vi. Now investigate the INTENSITY and FOCUS controls:
When these are correctly set, the spot will be reasonably bright but not glaring, and as sharply
focused as possible. (The TR control is screwdriver adjusted. It is only needed if the spot
moves at an angle rather than horizontally across the screen with no signal connected.)
14
Adjusting the INTENSITY control changes the brightness of the oscilloscope display. The
FOCUS should be set to produce a bright clear trace. If required, TR can be adjusted using a
small screwdriver so that the oscilloscope trace is exactly horizontal when no signal is
connected.
vii. The TIME/DIV control determines the horizontal scale of the graph which
appears on the oscilloscope screen.
viii. The VOLTS/DIV controls determine the vertical scale of the graph drawn on the
oscilloscope screen.
The diagram shows a lead with a BNC plug at one end and crocodile clips at the
other. Adjust VOLTS/DIV and TIME/DIV until you obtain a clear picture of the
signal, which should look like this:
DC/AC/GND slide switches: In the DC position, the signal input is connected

directly to the Y-amplifier of the corresponding channel, CH I or CH II. In the AC
position, a capacitor is connected into the signal pathway so that DC voltages are
blocked and only changing AC signals are displayed.
In the GND position, the input of the Y-amplifier is connected to 0 V. This allows you
to check the position of 0 V on the oscilloscope screen.
Trace selection switches: The settings of these switches control which traces
appear on the oscilloscope screen.
15
STUDY OF LOGIC GATES

AIM:
To study about logic gates and verify their truth tables.
COMPONENTS REQUIRED:
SL No. COMPONENT SPECIFICATION
1. AND GATE IC 7408
2. OR GATE IC 7432
3. NOT GATE IC 7404
4. NAND GATE 2 I/P IC 7400
5. NOR GATE IC 7402
6. X-OR GATE IC 7486
7. NAND GATE 3 I/P IC 7410
8. IC TRAINER KIT -
9. PATCH CORD -
THEORY:
Circuit that takes the logical decision and the process are called logic gates. Each gate
has one or more input and only one output. OR, AND , NOT are basic gates. NAND, NOR
and X-OR are known as universal gates. Basic gates form these gates.
AND GATE:
The AND gate performs a logical multiplication commonly known as AND function.
The output is high when both the inputs are high. The output is low level when any one of the
inputs is low.
OR GATE:
The OR gate performs a logical addition commonly known as OR function. The output is
high when any one of the inputs is high. The output is low level when both the inputs are low.
16
NOT GATE:
The NOT gate is called an inverter. The output is high when the input is low. The
output is low when the input is high.
NAND GATE:
The NAND gate is a contraction of AND-NOT. The output is high when both inputs
are low and any one of the input is low .The output is low level when both inputs are high.
NOR GATE:
The NOR gate is a contraction of OR-NOT. The output is high when both inputs are
low. The output is low when one or both inputs are high.
X-OR GATE:
The output is high when any one of the inputs is high. The output is low when both
the inputs are low and both the inputs are high.
PROCEDURE:
(i) Connections are given as per circuit diagram.

(ii) Logical inputs are given as per circuit diagram.
(iii) Observe the output and verify the truth table.
17
AND GATE:
SYMBOL: PIN DIAGRAM:
OR GATE:
18
NOT GATE:
X-OR GATE :
SYMBOL : PIN DIAGRAM :
19
2-INPUT NAND GATE:
3-INPUT NAND GATE :
20
NOR GATE:
RESULT:
The truth tables of logic gates is verified.
21
EXPERIMENT 1
SCHMITT TRIGGER
AIM: Design and construct a Schmitt trigger circuit using op-amp for the given UTP
and LTP values and demonstrate its working..
COMPONENTS REQUIRED: IC μA741, Resistor of 10KΩ, 100KΩ, DC regulated power

supply, Signal generator, CRO
DESIGN :
1)Let given UTP = 2.5 V, LTP= 1V. Assume Vsat = 12 V
R1Vref R2Vsat
UTP   where Vsat is the positive saturation of the opamp cc
R1  R2 R1  R2
R1Vref R2Vsat
& LTP  
R1  R2 R1  R2
Hence given the LTP & UTP values to find the R1 , R2 & Vref values, the following design is used.
2 R1Vref
UTP  LTP  - - - - - -(1)
R1  R2
2 R1Vsat
UTP  LTP  - - - - - -(2)
R1  R2
Let Vsat  12V, UTP  2.5 V & LTP  1V, then equation (2) yields R1  15 R2
Let R2  1K, then R1  15 K
(UTP  LTP)( R1  R2 )
From equation (1) we have Vref   1.88V
2 R1
Circuit Diagram and actual connections of Schmitt Trigger Circuit
22
DESIGN 2)
Let given UTP = 2 V, LTP= -1V. Assume Vsat = 12 V

R1Vref RV
UTP   2 sat where Vsat is the positive saturation of the opamp cc
R1  R2 R1  R2
R1Vref R2Vsat
& LTP  
R1  R2 R1  R2
2 R1Vref
UTP  LTP  - - - - - -(1)
R1  R2
2 R1Vsat
UTP  LTP  - - - - - -(2)
R1  R2
Let Vsat  12V, UTP  2 V & LTP  - 1V, then equation (2) yields R1  7 R2
Let R2  1K, then R1  7 K
(UTP  LTP)( R1  R2 )
2 R1
Design 3) Let given UTP = 4V, LTP= 2V. Assume Vsat = 12 V
R1Vref RV
UTP   2 sat where Vsat is the positive saturation of the opamp
R1  R2 R1  R2
R1Vref R2Vsat
& LTP  
R1  R2 R1  R2
2 R1Vref
UTP  LTP  - - - - - -(1)
R1  R2
2 R1Vsat
UTP  LTP  - - - - - -(2)
R1  R2
Let Vsat  12V, UTP  4 V & LTP  2V, then equation (2) yields R1  9 R2
R2  10 K, then R1  90 K
(UTP  LTP)( R1  R2 )
2 R1
23
THEORY:
Schmitt Trigger converts an irregular shaped waveform to a square wave or pulse.

Here, the input voltage triggers the output voltage every time it exceeds certain voltage levels
called the upper threshold voltage VUTP and lower threshold voltage VLTP. The input voltage
is applied to the inverting input. Because the feedback voltage is aiding the input voltage, the
feedback is positive. A comparator using positive feedback is usually called a Schmitt
Trigger. Schmitt Trigger is used as a squaring circuit, in digital circuitry, amplitude
comparator, etc.
PROCEDURE:
1. Before doing the connections, check all the components using multimeter.
2. Make the connection as shown in circuit diagram.
3. Using a signal generator apply the sinusoidal input waveform of peak-to-peak
amplitude of 10V, frequency 1kHz.
4. Keep the CRO in dual mode; apply input (Vin) signal to the channel 1 and observe the
output (Vo) on channel 2 which is as shown in the waveform below. Note the
amplitude levels from the waveforms.
5. Now keep CRO in X-Y mode and observe the hysteresis curve.
WAVEFORMS:
CRO in DUAL mode CRO in X-Y mode showing the Hysteresis curve
RESULT: Hysteresis is UTP-LTP=______V
24
EXPERIMENT 2
OP-AMP AS A RELAXATION OSCILLATOR
AIM: Design and construct a rectangular waveform generator (op-amp relaxation oscillator)
for a given frequency and demonstrate its working.
Op-amp μA741, Resistor of 1KΩ, 10KΩ, 20 kΩ Potentiometer, Capacitor of 0.1 μF,

Regulated DC power supply, CRO
THEORY:
Op-Amp Relaxation Oscillator is a simple Square wave generator which is also called
as a Free running oscillator or Astable multivibrator or Relaxation oscillator. In this figure
the op-amp operates in the saturation region. Here, a fraction (R1/(R1+R2)) of output is fed
back to the non-inverting input terminal. Thus reference voltage is (R1/(R1+R2)) Vo and
may take values as +(R1/(R1+R2)) Vsat or - (R1/(R1+R2)) Vsat. The output is also fed back
to the inverting input terminal after integrating by means of a low-pass RC combination.
Thus whenever the voltage at inverting input terminal just exceeds reference voltage,
switching takes place resulting in a square wave output.
If R1 = R2, we have T = 2RC ln (3)
Another example, if R2=1.16 R1, then T = 2RC ----------(2)
DESIGN:
1  
The period of the output rectangular wave is given as T  2RC ln   -------(1)
1  
R1
Where,   is the feedback fraction
R1  R2
25
1 1
Example: Design for a frequency of 1 kHz (implies T   3  10 3  1ms )
f 10
Use R2=1.16 R1,
Let R1 = 10kΩ, then R2 = 10 kΩ (use 20kΩ potentiometer)
Choose next a value of C and then calculate value of R from equation (2).
T 10 3
Let C=0.1µF (i.e., 10-7), then R    5K
2C 2  10 7
R1
The voltage across the capacitor has a peak voltage of Vc  Vsat
R1  R2
Values
C=0.1μF
R2
R1 = 10kΩ, R2 = 11.6 kΩ,R = 4.7k/5.1kΩ
R1
26
PROCEDURE:
1. Before making the connections check all the components using multimeter.
2. Make the connections as shown in figure and switch on the power supply.
3. Observe the voltage waveform across the capacitor on CRO.
4. Also observe the output waveform on CRO. Measure its amplitude and frequency.
WAVEFORMS
RESULT:
The frequency of the oscillations = …………Hz.
27
EXPERIMENT 3
ASTABLE MULTIVIBRATOR USING 555 TIMER
AIM: Design and implement an astable multivibrator using 555 Timer for a given frequency
and duty cycle.
a) Duty cycle = 75 % and f = 1 KHz
b) Duty cycle = 50% and f = 1 KHz
COMPONENTS REQUIRED: 555 Timer IC, Resistors of 3.3KΩ, 6.8KΩ, Capacitors of

0.1 μF, 0.01 μF, Regulated power supply, CRO.
THEORY:
Multivibrator is a form of oscillator, which has a non-sinusoidal output. The output

waveform is rectangular. The multivibrators are classified as: Astable or free running
multivibrator: It alternates automatically between two states (low and high for a rectangular
output) and remains in each state for a time dependent upon the circuit constants. It is just an
oscillator as it requires no external pulse for its operation. Monostable or one shot
multivibrator: It has one stable state and one quasi stable. The application of an input pulse
triggers the circuit time constants. After a period of time determined by the time constant, the
circuit returns to its initial stable state. The process is repeated upon the application of each
trigger pulse. Bistable Multivibrators: It has both stable states. It requires the application of
an external triggering pulse to change the output from one state to other. After the output has
changed its state, it remains in that state until the application of next trigger pulse. Flip flop is
an example.
28
DESIGN:
Case i) For Duty Cycle > 50%
Given frequency (f) = 1 KHz and duty cycle = 75% (=0.75)
Therefore T=1/f=1ms=Ton+Toff=1ms
Capacitor charges through RA and RB there for charging time is given by
Ton=0.693(RA+RB) C
during this time the output is High, so
Ton=0.693(RA+RB) C = 0.75 ms -------------------------------(1)
Capacitor discharges through R2 only there for discharging time is given by
Toff=0.693 RB C,
During this time the output is Low, so
Toff=0.693 RB C = 0.25 ms -------------------------------------(2)
T = Ton + Toff = 0.693 (RA +2 RB) C=1ms
Duty Cycle is calculated by the following manner=Ton/Ton+Toff=0.75
Duty cycle = Ton / T = 0.75. Hence Ton = 0.75T = 0.75 ms and Toff = T – TC = 0.25ms.
Let C=0.1μF and substituting in the above equations,
RB = 3.6 KΩ (from equation 2) and
RA = 7.2KΩ (from equation 1 & RB values).
Choose RA = 6.8kΩ and RB = 3.3kΩ.
The Vcc determines the upper and lower threshold voltages (observed from the capacitor
2 1
voltage waveform) as VUT  VCC & VLT  VCC .
3 3
29
Note: The duty cycle determined by RA & RB can vary only between 50 & 100%. If RA is
much smaller than RB, the duty cycle approaches 50%.
Circuit Diagram and actual connections
Case ii) For Duty Cycle = 50%
Therefore T=1/f=1ms=Ton+Toff=1ms
Given frequency (f) = 1 KHz and duty cycle = 50% (=0.5)
To achieve a duty cycle of less than or equal to 50% is to connect a diode D across resistor
RB
The time for which the output is high is given by
tON = tC = 0.693 ( RA )*C
tOFF = td= 0.693 ( RB )*C
Thus the total period of the output waveform is
T = tON + toff = 0.693 ( RA + RB )*C=1ms
For duty cycle equal to 50% RA needs to be equal to resistor RB.

30
For RA=RB=R,
T=0.693*2RA*C=1ms
Therefore 2RA=14.4 kΩ.
Hence RA=7.2 kΩ =RB
Astable Multivibrator using 555 for 50% Duty Cycle
For RA < RB , the duty cycle is less than 50%.
In this case, the capacitor C charges through RA and diode D to approximately 2/3 Vcc and
discharges through RB until the capacitor voltage equals approximately 1/3 Vcc, after which
the cycle repeats.
PROCEDURE:
1. Before making the connections, check the components using multimeter.

2. Make the connections as shown in figure and switch on the power supply.
3. Observe the capacitor voltage waveform at 6th pin of 555 timer on CRO.
4. Observe the output waveform at 3rd pin of 555 timer on CRO (shown below).
5. Note down the amplitude levels, time period and hence calculate duty cycle.
31
WAVEFORMS
Results:
An astable multivibrator of given duty cycle and frequency is designed. A comparison of the
experimental values with the given ones is represented below:
The frequency of the oscillations = ………….Hz.
Quantity Theoretical Experimental

measured value value
Frequency
Duty Cycle
32
EXPERIMENT NO.4
DESIGN OF ADDER AND SUBTRACTOR

AIM:
To design and construct half adder, full adder, half subtractor and full subtractor
circuits and verify the truth table using logic gates.
Sl.No. COMPONENT SPECIFICATION
1. AND GATE IC 7408

2. X-OR GATE IC 7486
3. NOT GATE IC 7404
4. OR GATE IC 7432
3. IC TRAINER KIT -
4. PATCH CORDS -
THEORY:
HALF ADDER:
A half adder has two inputs for the two bits to be added and two outputs one from the
sum ‘ S’ and other from the carry ‘ c’ into the higher adder position. Above circuit is called as
a carry signal from the addition of the less significant bits sum from the X-OR Gate the carry
out from the AND gate.
FULL ADDER:
A full adder is a combinational circuit that forms the arithmetic sum of input; it
consists of three inputs and two outputs. A full adder is useful to add three bits at a time but a
half adder cannot do so. In full adder sum output will be taken from X-OR Gate, carry output
will be taken from OR Gate.
33
HALF SUBTRACTOR:
The half subtractor is constructed using X-OR and AND Gate. The half subtractor has
two input and two outputs. The outputs are difference and borrow. The difference can be
applied using X-OR Gate, borrow output can be implemented using an AND Gate and an
inverter.
FULL SUBTRACTOR:
The full subtractor is a combination of X-OR, AND, OR, NOT Gates. In a full
subtractor the logic circuit should have three inputs and two outputs. The two half subtractor
put together gives a full subtractor .The first half subtractor will be C and A B. The output
will be difference output of full subtractor. The expression AB assembles the borrow output
of the half subtractor and the second term is the inverted difference output of first X-OR.
HALF ADDER TRUTH TABLE:
A B CARRY SUM
0 0 0 0
0 1 0 1
1 0 0 1
1 1 1 0
K-Map for SUM: K-Map for CARRY:
SUM = A’B + AB’ CARRY = AB
34
35
FULL ADDER
LOGIC DIAGRAM:
FULL ADDER USING TWO HALF ADDER
TRUTH TABLE:
A B C CARRY SUM
0 0 0 0 0
0 0 1 0 1
0 1 0 0 1
0 1 1 1 0
1 0 0 0 1
1 0 1 1 0
1 1 0 1 0
1 1 1 1 1
36
K-Map for SUM: K-Map for CARRY:
SUM = A’B’C + A’BC’ + ABC’ + ABC CARRY = AB + BC + AC
LOGIC DIAGRAM:
37
HALF SUBTRACTOR
TRUTH TABLE:
A B BORROW DIFFERENCE
0 0 0 0
0 1 1 1
1 0 0 1
1 1 0 0
K-Map for DIFFERENCE: K-Map for BORROW:
DIFFERENCE = A’B + AB’ BORROW = A’B
38
LOGIC DIAGRAM:
39
FULL SUBTRACTOR
FULL SUBTRACTOR USING TWO HALF SUBTRACTOR:
40
TRUTH TABLE:
A B C BORROW DIFFERENCE
0 0 0 0 0
0 0 1 1 1
0 1 0 1 1
0 1 1 1 0
1 0 0 0 1
1 0 1 0 0
1 1 0 0 0
1 1 1 1 1
K-Map for Difference: K-Map for Borrow
Difference = A’B’C + A’BC’ + AB’C’ + ABC Borrow = A’B + BC + A’C
41
PROCEDURE:
(i) Connections are given as per circuit diagram.

(ii) Logical inputs are given as per circuit diagram.
(iii) Observe the output and verify the truth table.
RESULT:
42
EXPERIMENT 5
REALISATION OF LOGIC EXPRESSION USING 8:1 MULTIPLEXER
AIM: To simplify a given 4-variable logic expression using Entered Variable Map and to
realize the simplify logic expression using 8:1 multiplexer IC.
Sl.No Components
1. Trainer Kit
2. Patch Chords
3. IC 74151
4. IC 7404
THEORY:
Multiplex means many into one. A multiplexer is a circuit with many inputs but only one
output. The inputs of the multiplexer are divided into two categories namely, data inputs and
select inputs. A multiplexer having ‘n’ data inputs have ‘m’ control signals such that n≤ 2m.
Depending on the value of the select inputs, data on one of the ‘n’ inputs is steered to the
output. The figure shows the block diagram of a multiplexer.
Multiplexer can be used to implement any logic expression. Commercial multiplexer ICs
come in integer power of 2, e.g. 2-to-1, 4-to-1, 8-to-1, 16-to-1 multiplexers. Hence to
implement a logic expression with ‘n’ variables, a multiplexer with ‘n’ select inputs is needed
i.e. 2n – to-1 multiplexer. Hence it is called as universal logic circuit.
43
PIN DIAGRAM 74151
DESIGN:
Consider the 4-variable logic expression
Example 1) Y= F (A, B, C, D) = Σ m(0, 2, 3, 4,

5, 8, 9, 10, 11, 12, 13, 15)
This expression is equivalent to the following

truth table.
44
To realize this expression using as 8-to-1 multiplexer:
Step 1: Any 3 variables are fed as select inputs. The fourth variable is then the data input. In
the example, variables A, B and C are selected as the select inputs and D the data input.
Step 2:
i. Write all the combinations of 3 select inputs (row 1)
ii. For each value of the 4th variable D, write the corresponding output. (Row 2 & 3)
iii. Write Y as a function of d (row 4)

iv. Assign data input values for 8-to-1 MUX by copying Y values obtained in row 4.
Note: The data inputs of a 8:1 MUX are labelled D0 to D7
Example 2) Simplify the function using MEV technique
f(A,B,C,D)= Σm (2,4,5,12,15) + d(0,1,10,11).
45
Method 2)
f (A,B,C,D) = Σm(2,3,4,5,13,15) + d(8,9,10,11).
Rules to obtain implementation table:

If both A’ and A are not marked (ie. circled), then the output of D0=0.
If both A’ and A are marked then the output of D1=1.
If 2 is marked and 10 is not circled , then take the value of that row which is circled. In this
example, 2 is circled ∴ consider its corresponding row =A’ as value of D2.∴D2 = A’
11 is marked and 3 is not marked. Hence take 11’s value = A . ∴ D3 =A.
PROCEDURE:
1. Simplify the given logic expression using Map entered variable map.
2. Check all the IC components using digital IC tester.
3. Make connections as per the circuit diagram.
4. Give supply to the trainer kit.
5. Provide input data to the circuit via switches
6. Verify the truth table sequence. Observe the outputs.
RESULT:
A four-variable logic expression is simplified using entered variable map and is verified
using 8:1 multiplexer.
46
EXPT NO. :6
DESIGN AND IMPLEMENTATION OF CODE CONVERTOR

AIM:
To design and implement 4-bit
(i) Binary to Gray code converter

(ii) Gray to binary code converter
Sl.No. COMPONENT SPECIFICATION QTY.

1. X-OR GATE IC 7486 1
2. AND GATE IC 7408 1
3. OR GATE IC 7432 1
4. NOT GATE IC 7404 1
5. IC TRAINER KIT - 1
6. PATCH CORDS - 35
THEORY:
A code converter is a circuit that makes the two systems compatible even though each
uses a different binary code. Each one of the four maps represents one of the four outputs of
the circuit as a function of the four input variables. A two-level logic diagram may be
obtained directly from the Boolean expressions derived by the maps.
The input variable are designated as B3, B2, B1, B0 and the output variables are
designated as C3, C2, C1, Co. from the truth table, combinational circuit is designed. The
Boolean functions are obtained from K-Map for each output variable.
47
BINARY TO GRAY CODE CONVERSION
Steps: The example shows the steps involved in conversion of a binary code to its gray code.
Binary code taken for the example is 1011. In the conversion process the most significant bit
(MSB) of the binary code is taken as the MSB of the Gray code. The bit positions G2, G1 and
G0 is obtained by adding (B3, B2),(B2, B1) and (B1, B0) respectively, ignoring the carry
generated. From the K-Map simplification
TRUTH TABLE:
Binary input Gray code output
B3 B2 B1 B0 G3 G2 G1 G0
0 0 0 0 0 0 0 0
0 0 0 1 0 0 0 1
0 0 1 0 0 0 1 1
0 0 1 1 0 0 1 0
0 1 0 0 0 1 1 0
0 1 0 1 0 1 1 1
0 1 1 0 0 1 0 1
0 1 1 1 0 1 0 0
1 0 0 0 1 1 0 0
1 0 0 1 1 1 0 1
1 0 1 0 1 1 1 1
1 0 1 1 1 1 1 0
1 1 0 0 1 0 1 0
1 1 0 1 1 0 1 1
1 1 1 0 1 0 0 1
1 1 1 1 1 0 0 0
48
K-Map for G3: K-Map for G2:
G3 = B3
K-Map for G1: K-Map for G0:
49
For binary to Gray code conversion the following Boolean expressions are obtained,
LOGIC DIAGRAM:
BINARY TO GRAY CODE CONVERTOR
Gray to Binary Code Conversion Steps:
The example shows the steps involved in conversion of a Gray code to binary code.
Gray code taken for the example is 1110
50
TRUTH TABLE:
| Gray Code | Binary Code |
G3 G2 G1 G0 B3 B2 B1 B0
0 0 0 0 0 0 0 0
0 0 0 1 0 0 0 1
0 0 1 1 0 0 1 0
0 0 1 0 0 0 1 1
0 1 1 0 0 1 0 0
0 1 1 1 0 1 0 1
0 1 0 1 0 1 1 0
0 1 0 0 0 1 1 1
1 1 0 0 1 0 0 0
1 1 0 1 1 0 0 1
1 1 1 1 1 0 1 0
1 1 1 0 1 0 1 1
1 0 1 0 1 1 0 0
1 0 1 1 1 1 0 1
1 0 0 1 1 1 1 0
1 0 0 0 1 1 1 1
51
K-Map for B3: K-Map for B2:
B3 = G3
K-Map for B1: K-Map for B0:
52
LOGIC DIAGRAM:
GRAY CODE TO BINARY CONVERTOR
In the conversion process the most significant bit (MSB) of the Gray code is taken as the
MSB of the binary code. The bit positions B2, B1 and B0 is obtained by adding (B3, G2),
(B2, G1) and (B1, G0) respectively, ignoring the carry generated. From the K-Map
simplification for Gray code to binary code conversion the following Boolean expressions are
obtained,
PROCEDURE:
(i) Connections were given as per circuit diagram.

(ii) Logical inputs were given as per truth table
(iii) Observe the logical output and verify with the truth tables.
RESULT:
Binary to Gray and Gray to Binary converters are designed, constructed using logic gates
and their truth table was verified.
53
EXPERIMENT 7
PARITY GENERATOR AND PARITY CHECKER
AIM:
Design and verify the Truth Table of 3-bit Parity Generator and 4-bit Parity Checker using
basic Logic Gates with an even parity bit.
COMPONENTS REQUIRED
IC7404, IC7410, IC7432, IC7486, Trainer kit, Patch chords.
THEORY:
Parity Generator: It is combinational circuit that accepts an n-1 bit stream data and generates
the additional bit that is to be transmitted with the bit stream. This additional or extra bit is
termed as a parity bit. In even parity bit scheme, the parity bit is ‘0’ if there are even number
of 1s in the data stream and the parity bit is ‘1’ if there are odd number of 1s in the data
stream. In odd parity bit scheme, the parity bit is ‘1’ if there are even numbers of 1s in the
datastream and the parity bit is ‘0’ if there are odd number of 1s in the data stream. Let us
discuss both even and odd parity generators.
Parity Checker: It is a logic circuit that checks for possible errors in the transmission. This
circuit can be an even parity checker or odd parity checker depending on the type of parity
generated at the transmission end. When this circuit is used as even parity checker, the
number of input bits must always be even. When a parity error occurs, the ‘sum even’ output
goes low and ‘sum odd’ output goes high. If this logic circuit is used as an odd parity
checker, the number of input bits should be odd, but if an error occurs the ‘sum odd’ output
goes low and ‘sum even’ output goes high.
54
DESIGN:
Even Parity Generator
Let us assume that a 3-bit message is to be transmitted with an even parity bit. Let the three
inputs A, B and C are applied to the circuits and output bit is the parity bit P. The total
number of 1s must be even, to generate the even parity bit P. The figure below shows the
truth table of even parity generator in which 1 is placed as parity bit in order to make all 1s as
even when the number of 1s in the truth table is odd.
Even Parity Generator Truth Table
The K-map simplification for 3-bit message even parity generator is
K map for Even Parity Generator
From the above truth table, the simplified expression of the parity bit can be written as
55
The above expression can be implemented by using two Ex-OR gates. The logic diagram of
even parity generator with two Ex – OR gates are shown below.
The three bit message along with the parity generated by this circuit which is transmitted to
the receiving end where parity checker circuit checks whether any error is present or not.
Even Parity Checker
Consider that three input message along with even parity bit is generated at the transmitting
end. These 4 bits are applied as input to the parity checker circuit which checks the
possibility of error on the data. Since the data is transmitted with even parity, four bits
received at circuit must have an even number of 1s.
If any error occurs, the received message consists of odd number of 1s. The output of the
parity checker is denoted by PEC (parity error check).
The below table shows the truth table for the even parity checker in which PEC = 1 if the
error occurs, i.e., the four bits received have odd number of 1s and PEC = 0 if no error
occurs, i.e., if the 4-bit message has even number of 1s.
Even Parity Checker Truth Table
56
The above truth table can be simplified using K-map as shown below.
K map for Even Parity Checker
The above logic expression for the even parity checker can be implemented by using three
Ex-OR gates as shown in figure.
Even Parity Checker Logic Circuit
RESULT:
3-bit Parity generator and 4-bit parity checker using even parity is implemented using basic
gates. And truth table is verified.
57
EXPERIMENT NO 8
J-K MASTER/SLAVE FF USING NAND GATES
AIM: To realize a J-K Master/Slave flip flop using NAND gates and verify its truth table.
Sl.No Components Quantity

1. Trainer kit. 01
2. Patch chords 30
3. IC 74LS00 01
4. IC 74LS10 02
THEORY:
The Q and Q' outputs will only change state on the falling edge of the CLK signal, and
the J and K inputs will control the future output
If both the J and K inputs are held at logic 1 and the CLK signal continues to change, the
Q and Q' outputs will simply change state with each falling edge of the CLK signal.
(The master latch circuit will change state with each rising edge of CLK.)
Master Slave Flip Flop:
A JK master flip flop is positive edge triggered, whereas slave is negative edge triggered.
Therefore master first responds to J and K inputs and then slave. If J=0 and K=1, master
resets on arrival of positive clock edge. High output of the master drives the K input of the
slave. For the trailing edge of the clock pulse the slave is forced to reset. If both the inputs are
high, it changes the state or toggles on the arrival of the positive clock edge and the slave
toggles on the negative clock edge. The slave does exactly what the master does.
58
Pin Details of the ICs:
Clk J K Q --- comment

Q
0 0 Q0 ---- No change
Q0
0 1 0 1 Reset
1 0 1 0 Set
1 1 Q0 Q0 toggle
59
RESULT:
The J-K Master / Slave Flip Flop is designed using NAND gates and its truth table is verified
60
EXPERIMENT NO 9:
SYNCHRONOUS UP COUNTER
AIM:
Design and implement a mod n (n<8) synchronous up counter using JK FF IC’s and
demonstrate its working.
COMPONENTS USED:
IC 74LS76, IC 74LS08, Patch chords, power chords, and Trainer kit.
THEORY:
In digital logic and computing, a counter is a device which stores and displays the number of
times a particular event or process has occurred, often in relationship to a clock signal.
A synchronous counter is one whose output bits change state simultaneously. Such a
counter circuit can be built from JK flip-flop by connecting all the clock inputs together, so
that each and every flip-flop receives the exact same clock pulse at the exact same time. This
results in all the individual output bits changing state at exactly the same time in response to
the common clock signal with no ripple effect i.e. with no propagation delay.
By examining the four-bit binary count sequence, it noticed that just before a bit toggles, all
preceding bits are "high". That is a synchronous up-counter can be implemented by toggling
the bit when all of the less significant bits are at a logic high state. For example, bit 1 toggles
when bit 0 is logic high; bit 2 toggles when both bit 1 and bit 0 are logic high; bit 3 toggles
when bit 2, bit 1 and bit 0 are all high; and so on.
61
Pin diagram of 7476
IC 7476 contains 2 JK flip-flops with pre-set and clear signals.
PR CLR CLK J K Q Q’
L H X X X H L
H L X X X L H
L L X X X H H
H H L L Q0 Q0’
H H H L H L
H H L H L H
H H H H Toggle
IC: 7408
62
Transition Table: Qn Qn+1 J K

0 0 0 X
0 1 1 X
1 0 X 1
1 1 X 0
63
64
Mod-5 Counter Synchronous Counter: This have five counter states. The counter design table
for such counter shows the three flip-flop and their states also (0 to 4 states). 6 inputs needed
for the three flip-flops.
Present State Next State Jc Kc Jb Kb Ja Ka
Qc Qb Qa Qc+1 Qb+1 Qa+1
0 0 0 0 0 1 0 x 0 x 1 x
0 0 1 0 1 0 0 x 1 x x 1
0 1 0 0 1 1 0 x x 0 1 x
0 1 1 1 0 0 1 x x 1 x 1
1 0 0 0 0 0 x 1 0 x 0 x
1 0 1 x x x x x x x x x
1 1 0 x x x x x x x x x
1 1 1 x x x x x x x x x
Jc = QbQa, Kc=1, Jb=Qa,Kb=Qa, Ja=Qc’ ,Ka=1
65
PROCEDURE:
1. Verify all the components and patch cords for good working condition.
2. Make connection as shown in the circuit diagram.
3. Give supply to the trainer kit
4. Provide input data to circuit via switches and verify the truth table.
RESULT:
The mod-n synchronous counter is successfully implemented by using the JK Flip Flop.
66
EXPERIMENT NO 10
AIM: Design and implement asynchronous counter using decade counter IC to count up from
0 to n (n≤9) and demonstrate its working.
COMPONENTS USED: IC 74LS90, Patch chords, Power chords and Trainer kit.
THEORY:
Asynchronous counter is a counter in which the clock signal is connected to the clock input
of only first stage flip flop. The clock input of the second stage flip flop is triggered by the
output of the first stage flip flop and so on. This introduces an inherent propagation delay
time through a flip flop. A transition of input clock pulse and a transition of the output of a
flip flop can never occur exactly at the same time. Therefore, the two flip flops are never
simultaneously triggered, which results in asynchronous counter operation.
PIN DIAGRAM
67
CIRCUIT DIAGRAM:
Function Table:
Clock Qa Qb Qc Qd
0 0 0 0 0
1 0 0 0 1
2 0 0 1 0
3 0 0 1 1
4 0 1 0 0
5 0 1 0 1
6 0 1 1 0
8 0 1 1 1
9 1 0 0 0
RESULT:
An asynchronous counter using a decade counter is designed and the truth table is verified for
the same.
68
EXPERIMENT NO 11
AIM: - To Study 4 Bit ALU (IC74181).
APPARATUS REQUIRED: IC 74181, etc.
THEORY:
The 74181 is a 7400 series medium-scale integration (MSI) TTL integrated circuit,
containing the equivalent of 75 logic gates and most commonly packaged as a 24-pin DIP.
The 4-bit wide ALU can perform all the traditional add / subtract / decrement operations with
or without carry, as well as AND / NAND, OR / NOR, XOR, and shift. Many variations of
these basic functions are available, for a total of 16 arithmetic and 16 logical operations on
two four-bit words. Multiply and divide functions are not provided but can be performed in
multiple steps using the shift and add or subtract functions. Shift is not an explicit function
but can be derived from several available functions including (A+B) plus A.
69
70
VIVA QUESTIONS
1. Draw the basic structure of an N channel junction field effect transistor.
2. Why is FET known as a unipolar device?
3. What are the advantages and disadvantages of JFET over BJT?
4. What is a channel?
5. Distinguish between JFET and MOSFET.
6. What is an effect of cascading?
7. What are all the factors affecting the bandwidth of the RC Coupled amplifier?
8. Explain bypass capacitor?
9. What is meant by coupling capacitor?
10. Why does amplifier gain reduce?
11. Explain the different regions in frequency response?
12. State the types of distortions in amplifier?
13. What is cross over distortion? How it can be eliminated?
14. Define noise?
15. Draw the symbol of JFET and MOSFET.
16. What are the two modes of MOSFET?
17. Define pinch-off voltage
18. What is feedback and what are feedback amplifiers?
19. What is meant by positive and negative feedback?
20. What are the advantages and disadvantages of negative feedback?
21. Differentiate between voltage and current feedback in amplifiers?
22. What is the type of feedback used in an op- amp Schmitt trigger?
23. Give the expression for the frequency of oscillations in an op-amp sine wave oscillator?
24. What are the conditions for sustained oscillations or or what is Barkhausen criterion
25. What are the classifications of Oscillators?
26. What are the types of feedback oscillators?
27. Define Piezo-electric effect?
28. Draw the equivalent circuit of crystal oscillator?
29. How does an oscillator differ from an amplifier?
71
VIVA QUESTIONS ON LOGIC DESIGN
1. Why NAND & NOR gates are called universal gates?

2. Realize the EX – OR gates using minimum number of NAND gates.
3. Give the truth table for EX-NOR and realize using NAND gates?
4. Compare TTL logic family with CMOS family?
5. Which logic family is fastest and which has low power dissipation?
6. What are the different methods to obtain minimal expression?
7. What is a Min term and Max term
8. State the difference between SOP and POS.
9. What is meant by canonical representation?
10. What is K-map? Why is it used?
11. What is a multiplexer?
12. What is a de-multiplexer?
13. What are the applications of multiplexer and de-multiplexer?
14. Derive the Boolean expression for multiplexer and de-multiplexer.
15. In a 2n to 1 multiplexer how many selection lines are there?
16. Implement an 8:1 mux using 4:1 mux?
17. What is a comparator?
18. What are the applications of comparator?
19. Derive the Boolean expressions of one bit comparator and two bit comparators.
20. How do you realize a higher magnitude comparator using lower bit comparator?
21. Design a 2 bit comparator using a single Logic gates?
22. Design an 8 bit comparator using a two numbers of IC 7485?
23. What are the applications of decoder?
24. What is the difference between decoder & encoder?
25. For n- 2n decoder how many i/p lines & how many o/p lines?
26. Using 3:8 decoder and associated logic, implement a full adder
27. What is the difference between decoder and de-mux?
28. What are the different types of LEDs?
29. What are the applications of LEDs?
30. What is a priority encoder?
31. What is the difference between Flip-Flop & latch?
32. Give examples for synchronous & asynchronous inputs?
33. What are the applications of different Flip-Flops?
72
34. What is the advantage of Edge triggering over level triggering?

35. What is the relation between propagation delay & clock frequency of flip-flop?
36. What is race around in flip-flop & how to overcome it?
37. Convert the J K Flip-Flop into D flip-flop and T flip-flop
38. List the functions of asynchronous inputs?
39. What is the necessity for sequence generation?
40. What are PISO, SIPO, and SISO with respect to shift register?
41. Differentiate between serial data & parallel data
42. What is the significance of Mode control bit?
43. What is a ring counter?
44. What is a Johnson counter?
45. How many Flip-flops are present in IC 7495?
46. What is an asynchronous counter?
47. How is it different from a synchronous counter?
48. Realize asynchronous counter using T flip-flop
49. What are synchronous counters?
50. What are the advantages of synchronous counters?
51. What is an excitation table?
52. Write the excitation table for D, T FF
53. Design mod-5 synchronous counter using T FF
54. What is a presettable counter?
55. What are the applications of presettable counters?
56. Write the circuit for preset value of 0100 and N=5 (up counter)
57. What is a decade counter?
58. What do you mean by a ripple counter?
73

Department of Information Science and Engineering Analog and Digital Electronics Lab Subject Code: 17Csl37 Lab Manual

Uploaded by

Copyright:

Available Formats

Department of Information Science and Engineering Analog and Digital Electronics Lab Subject Code: 17Csl37 Lab Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Department of Information Science and Engineering Analog and Digital Electronics Lab Subject Code: 17Csl37 Lab Manual

Uploaded by

Copyright:

Available Formats

DEPARTMENT OF INFORMATION

SCIENCE AND ENGINEERING

ANALOG AND DIGITAL ELECTRONICS LAB

PESIT – BANGALORE SOUTH CAMPUS

1Km before Electronics City, Hosur Road,

ANALOG AND DIGITAL ELECTRONICS LABORATORY

Descriptions (if any)

10. Design and implement an asynchronous counter using decade counter IC to

RULES AND REGULATIONS

Rules for Maintaining Laboratory Record

Rules for Maintaining Observation Book

OBSERVATION BOOK CONTENTS

INTRODUCTION TO ADE LAB

Resistor Colour Code:

Picofarad Nanofarad Microfarad Picofarad Nanofarad Microfarad

The screen of this oscilloscope has 8 squares or

Setting up the CRO

a) all push button switches are in the OUT position

v. Find the Y-POS 1 control:

vi. Now investigate the INTENSITY and FOCUS controls:

DC/AC/GND slide switches: In the DC position, the signal input is connected

STUDY OF LOGIC GATES

1. AND GATE IC 7408

3. NOT GATE IC 7404

4. NAND GATE 2 I/P IC 7400

5. NOR GATE IC 7402

6. X-OR GATE IC 7486

7. NAND GATE 3 I/P IC 7410

(i) Connections are given as per circuit diagram.

SYMBOL: PIN DIAGRAM:

SYMBOL: PIN DIAGRAM:

SYMBOL : PIN DIAGRAM :

2-INPUT NAND GATE:

SYMBOL: PIN DIAGRAM:

3-INPUT NAND GATE :

and LTP values and demonstrate its working..

COMPONENTS REQUIRED: IC μA741, Resistor of 10KΩ, 100KΩ, DC regulated power

1)Let given UTP = 2.5 V, LTP= 1V. Assume Vsat = 12 V

Circuit Diagram and actual connections of Schmitt Trigger Circuit

Let given UTP = 2 V, LTP= -1V. Assume Vsat = 12 V

Schmitt Trigger converts an irregular shaped waveform to a square wave or pulse.

RESULT: Hysteresis is UTP-LTP=______V

OP-AMP AS A RELAXATION OSCILLATOR

Op-amp μA741, Resistor of 1KΩ, 10KΩ, 20 kΩ Potentiometer, Capacitor of 0.1 μF,

If R1 = R2, we have T = 2RC ln (3)

Another example, if R2=1.16 R1, then T = 2RC ----------(2)

Use R2=1.16 R1,

Let R1 = 10kΩ, then R2 = 10 kΩ (use 20kΩ potentiometer)

The frequency of the oscillations = …………Hz.

ASTABLE MULTIVIBRATOR USING 555 TIMER

a) Duty cycle = 75 % and f = 1 KHz

b) Duty cycle = 50% and f = 1 KHz

COMPONENTS REQUIRED: 555 Timer IC, Resistors of 3.3KΩ, 6.8KΩ, Capacitors of

Multivibrator is a form of oscillator, which has a non-sinusoidal output. The output

Case i) For Duty Cycle > 50%

Given frequency (f) = 1 KHz and duty cycle = 75% (=0.75)

Capacitor charges through RA and RB there for charging time is given by

during this time the output is High, so

Ton=0.693(RA+RB) C = 0.75 ms -------------------------------(1)