QM - 790 Service Manual V03

l
QM-790 Professional Mobile Radio
Service Manual
，LLC.
Quantun Electronics，
-0-
Contents
Revision History-------------------------------------------------------------------------------------------2
General-------------------------------------------------------------------------------------------3
Radio Overview------------------------------------------------------------------------------------------4
Software Specifications---------------------------------------------------------------------------------------9
Circuit Description------------------------------------------------------------------------------------------15
MCU PIN Function------------------------------------------------------------------------------------------19
Terminal Function------------------------------------------------------------------------------------------21
Tuning Description-----------------------------------------------------------------------------------------24
Troubleshooting Flow Chart------------------------------------------------------------------------------35
Disassembly and Assembly for Repair----------------------------------------------------------------39
Exploded View-----------------------------------------------------------------------------------------42
QM-790 Mechanical Parts List --------------------------------------------------------------------------- 43
QM-790 PCB View--------------------------------------------------------------------------------------------44
QM-790 Electronic Parts List ----------------------------------------------------------------------------52
QM-790 Block Diagram---------------------------------------------------------------------------105
QM-790 Schematic Diagram---------------------------------------------------------------------106
Specifications---------------------------------------------------------------------------------------------115
1
QM-790 Service Manual
Revision History
P/N. Date of Issue Changes Note
7130790010 2010,8,30 Initial release QM-970V PCB: P10A71V010
QM-790U PCB: P10A51U000
-2-
General
Manual Scope
This manual is intended for use by experienced technicians familiar with similar types of
communication equipment. It contains all service information required for the equipment and is current
as of the publication date.
Precautions
Safety Standards
● Do not operate your radio when someone is either touching or standing within 2 or 3 feet of
the antenna, to avoid the possibility of radio frequency burns or related physical injury.
● Do not operate the radio near electrical blasting caps or in an explosive atmosphere.
● Switch off the radio while refueling or parking at gas station.
● Turn off your radio in any place where posted notices instruct you to do so.
● Do not modify the radio for any reason.
● Do not expose the radio to direct sunlight over a long time, nor place it close to heating
source.
● Do not place the radio in excessively dusty, humid areas, nor on unstable surfaces.
● Refer the service to qualified technicians only.
Operation Safety Guidelines
● For vehicles equipped with electronic anti-skid braking systems, electronic ignition systems
or electronic fuel injection systems, interferences may occur during the radio transmission. If
the foregoing electronic equipments are installed on your vehicle, please contact your dealer
for further assistance to make sure that the radio transmission will not interfere with these
equipments.
● For radio installation in vehicles fueled by LP gas with LP gas container within interior of the
vehicles, the following precautions are recommended for personal safety.
(1) Any space containing radio equipment shall be isolated by a seal from the space in
which the LP gas container and its fittings are located.
(2) Remote (outside) fitting connections shall be used.
(3) Good ventilation is required for the container space.
Installation Safety Guidelines

● Do not mount the mobile radio overhead or on a sidewall unless you take special precautions.
● If someone were to remove the radio and fail to replace it properly, road shock could bump the
radio loose, and the falling radio could, in some circumstances, cause serious injury to the
driver or a passenger. In a crash, even when properly installed, the radio could break loose
and become a dangerous projectile.
3
Radio Overview
Front Panel
1 2 3 4
8 7 6 5
Figure 1
1. Volume Control Knob
Turn the Volume Control Knob clockwise to increase the volume, or counter-clockwise to decrease
the volume.
2. LCD
Please refer to the “LCD Display” section for details.
3. Programmable Functions Key ([▲]/[▼])
The [▲]/[▼] keys are programmable with auxiliary functions by your dealer. Please refer to the
“Programmable Auxiliary Functions” section.
4. LED Indicator
Please refer to the “LED Display” for detail.
5. Speaker
6. Power Switch
7. Programmable functions Keys ([P1]/[P2]/[P3]/[P4])
The [P1]/[P2]/[P3]/[P4] keys are programmable with auxiliary Functions by your dealer. Please
refer to the “Programmable Functions Keys” section.
8. Microphone Jack
Plug the microphone connector into this jack.
-4-
Radio Overview
Rear Panel
1 2 3 4 5
1. Antenna Pedestal
To connect the external antenna.
2. Power Inlet
Use the DC power cable supplied by Quantun to inlet 13.6v DC power supply.
3. 15PIN external interface
4. External Speaker Jack
Plug the external speaker connector (c3.5mm) into this jack.
5. GPS antenna Pedestal (Optional)
To connect the GPS antenna.
Microphone
5
Radio Overview
LCD Display
Indicator Description
1. Display zone/channel number.
2. Display zone/channel label
3. Display channel frequency
4. Display MDC1200
5. Display DTMF digit
6. Display GPS coordinates
7. Display menu, setting items, etc.
1. Appears when the selected channel is busy
2. The bar number indicate the channel RSSI
Appears when the transmitting power is low
Appears when squelch open
Appears when call transmission is selected
1. C Indicating that the selected channel is contained in the

scan list
2. C● Indicating that the selected channel is programmed as

priority channel 1
3. ●C Indicating that the selected channel is programmed as

priority channel 2
4. flashed appears when the scan function is activated
Appears when compander function is enabled
6
Radio Overview
Appears when scrambler function is enabled
Appears when GPS function is enabled
Appears when VOX function is enabled
Appears when the Aux port is activated
Programmable Auxiliary Functions
Your dealer may program the [P1]-[P4], [▲]/[▼] keys (long or short press) keys with one of the
following auxiliary functions respectively.
1. Off
2. CH Up
3. CH Down
4. Zone Up
5. Zone Down
6. Monitor A
7. Monitor B
8. Monitor C
9. Monitor D
10. Display Mode
11. User Selectable CTCSS/CDCSS(UST)
12. TX Power Select
13. 2-Tone/MDC1200/DTMF Call
14. Scan
15. Scan Add/Delete
16. Reverse Frequency
17. Talk Around
18. Select Squelch Level
19. Home Channel
20. Scrambler
21. Voice Compander
22. Emergency Call
23. VOX
24. GPS Data (optional)
25. Rent indicator
7
Radio Overview
26. Lone work
LED Indicator
Transmitting LED glows red
Receiving LED glows green when carrier

presents.
Scanning Green LED flashes once every 1

second.
Encoding (DTMF/PTT ID/2-Tone/MDC1200)
1) LED glows red while transmitting;
2) LED glows orange when
transmission ends.
Decoding (DTMF/2-Tone/MDC1200) Orange LED flashes after the
signaling is successfully decoded.
8
Software Specifications
1. Radio Modes
User Mode Conventional Mode
Panel Tuning Mode
Model Set Mode
Wired Clone Mode
Firmware Version Display Mode
PC Mode
2. Keypad Entry for Mode Startup
1) User Mode
Power on the radio to enter this mode. This is a normal mode.
2) Panel Tuning Mode
Operations:
● Press and hold down P1 to power on the radio. The radio enters Tuning Mode.
● Use ▲ / ▼ to select setting items. Press P4 to enter the sub-item of the selected item.
● Press P4 to enter the sub-item. Press ▲ / ▼ to tune the parameter. Press P4 again to
save the tuned data and move to the next item, or press P1 to return to the previous menu
without saving the tuned data.
9
＊＊＊:
＊＊＊ 1-256)
Setting Items and Display(＊＊＊
Wideband/
Setting item Main LCD Frequency Sub LCD Description
Narrowband
Center _C *** No signalling
High power
Tx HIGH Low _L *** No signalling
Wideband
Tx Power High _H *** No signalling
Low frequency
Tx LOW Low _L *** No signalling
Wideband
High _H *** No signalling
Wideband Low _L *** No signalling
Max Deviation MAX.DEV Medium band Center M_C *** No signalling
Center N_C *** No signalling
Narrow band Low N_L *** No signalling
High N_H *** No signalling
Center _C *** 100Hz square wave
Wideband
Low _L *** 100Hz square wave
CDCSS Balance CDCSS.BAL High _H *** 100Hz square wave
Medium band Center M_C *** 100Hz square wave
Narrow band Center N_C *** 100Hz square wave
10
Center _C *** CTCSS: 67.0Hz

Wideband Low _L *** CTCSS: 67.0Hz
CTC.DEV_L High _H *** CTCSS: 67.0Hz
Medium Center M_C *** CTCSS: 67.0Hz
Narrowband Center N_C *** CTCSS: 67.0Hz
CTC.DEV_
CSS Deviation High _H *** CTCSS: 151.4Hz
M
CTC.DEV_H High _H *** CTCSS: 254.1Hz
Center _C *** CDCSS: 023N
Wideband
Low _L *** CDCSS: 023N
CDCSS.DE
CDCSS Deviation High _H *** CDCSS: 023N
V
Medium Center M_C *** CDCSS: 023N
Narrowband Center N_C *** CDCSS: 023N
Center _C *** DTMF: 9
Wideband Low DTMF: 9
_L ***
DTMF Deviation DTMF.DEV High DTMF: 9
_H ***
Medium Center M_C *** DTMF: 9
Narrowband Center N_C *** DTMF: 9
Center _C *** 0XAAAQ
Wideband Low _L *** 0XAAAQ
MSK Deviation MSK.DEV High _H *** 0XAAAQ
Medium Center M_C *** 0XAAAQ
Narrowband Center N_C *** 0XAAAQ
Center _C *** 1KHz
Wideband Low _L *** 1KHz
Single Tone Deviation TONE DEV High _H *** 1KHz
Medium Center M_C *** 1KHz
Narrowband Center N_C *** 1KHz
11
- Low No signalling, SQL off

_L ***
Low-medium No signalling, SQL off
-
SENSITVITY frequency _LC ***
Rx Sensitivity
TY - Center No signalling, SQL off
_C ***
- Medium-high _HC *** No signalling, SQL off
High _H *** No signalling, SQL off

OPENSQL SQL 9
Low _L *** No signalling
9 Wideband
SQL 9 Medium Center M_C *** No signalling
SQL 9
Low N_L *** No signalling
Narrowband
SQL Open
OPENSQL SQL 3
Low No signalling
3 Wideband _L ***
SQL 3
Narrowband
SQL 9
Wideband
CLOS.SQL
9
SQL 9
Narrowband
SQL Close Center _C *** No signalling
SQL 3 Low _L *** No signalling

Wideband High No signalling
_H ***
CLOS.SQL High _H *** No signalling
3 SQL 3 Medium Center M_C *** No signalling
SQL 3
Narrowband
12
3. Model Set Mode

1) Press and hold down P2 to turn the radio on. The radio enters Model Set Mode. The frequency
range will be displayed on LCD.
2) Press ▲ / ▼ to select the band you need to reset model.
3) Press P4 to set the selected model. LED glows orange with WAIT on LCD. Then the
radio resets and enters User Mode.
Note:
1. Once the P4 key is pressed to set a new model, the previously stored channel data (frequency,
CTCSS/CDCSS, channel functions) will be cleared, and part of the functions will also change.
Therefore, do not make this operation unless it’s very necessary, such as replacing EEPROM, etc.
2. Initialization Data Table (FL: lowest frequency; FH: highest frequency; FC: center frequency) of
different models are shown in the following table.
Model Rx/Tx 1(C) 2(L) 3(H) 4 5 6 7 8

136-174 Rx(MHz) 155.15 136.15 173.85 145.55 164.50 155.00 155.20 155.40
(V) Tx(MHz) 155.00 136.00 174.00 145.50 164.50 155.00 155.20 155.40
435.15 400.15 469.85 452.50 435.00 435.20 435.40
400-470 Rx(MHz) 417.55
435.00 400.00 470.00 452.50 435.00 435.20 435.40
(U1) Tx(MHz) 417.50
485.15 450.15 519.85 497.50 485.00 485.20 485.40
450-520 Rx(MHz) 462.55
485.00 450.00 520.00 497.50 485.00 485.20 485.40
(U2) Tx(MHz) 462.50
QM-790 V: 136-174
QM-790 U1: 400-470
QM-790 U2: 450-520
1 2 3 5 6 7 8
CH 4
CTCSS Rx OFF OFF OFF OFF CTS67.0HZ DI454 151.4 DI454
CDCSS Tx OFF OFF OFF OFF CTS67.0HZ DI454 151.4 DI454
PWR Tx H H H L L L L L
CH CH 1 CH 2 CH 3 CH 4 CH 5 CH 6 CH 7 CH 8
NAME Wide Wide Wide N Wide Wide N N
4. Clone Mode
Data can be transferred from one radio to another either by wired cloning or wireless cloning.
■ Wired Clone Mode
1) Press and hold down P3 to power on the source radio. The radio enters Clone Mode with CLONE on
LCD. Or the radio enters User Mode when Clone Mode is set OFF by your local dealer.
2) Press P3 to toggle between Dealer Clone Mode and Factory Clone Mode. DEACLONE or
FACCLONE. appear on LCD when the corresponding mode is selected. The display reverts to the
original after 5 seconds. Dealer Clone Mode does not clone tuned data, embedded information, etc.
While Factory Clone Mode clones all data. The default clone mode is Dealer Clone Mode.
3) Connect the target radio with the wired clone cable and power it on.
13
4) Press P4 to start cloning. The LED of the source radio glows red and the data is transferred from the
source radio to the target radio. When receiving data, the LED of the target radio glows green with
PROGRAM on LCD. When the cloning is completed, the source radio displays END. The target radio
automatically enters User Mode after receiving all data.
5) Press P4 to return the source radio to Clone Mode. CLONE appears on LCD. Repeat the above steps
to continue wired clone.
5. Firmware Version Display Mode
Press P4 to power on the mobile radio and the firmware version appears on LCD. Release P4 to
enter User Mode automatically.
6. PC Mode
Connect the mobile radio with PC via the programming cable. Data can be sent to the radio from PC,
and then saved in EEPROM. Data programming and radio tuning are accessible via the
programming software.
1) PROGRAMM appears on LCD after data is transferred to the mobile radio from the computer. LED
glows green when data is being written to the radio and red when data is being read from the radio.
Radio will reset automatically when the programming is completed.
2) The following parameters can be tuned through the programming software.
● Tx High Power
● Tx Low Power
● Maximum Deviation
● CDCSS Balance
● CTCSS Deviation (67.0Hz)
● CDCSS Deviation (151.4Hz)
● DTMF Deviation (254.1Hz)
● MSK Deviation
● Single Tone Deviation
● Rx sensitivity
● Squelch Open 9
● Squelch Open 3
● Squelch Close 9
● Squelch Close 3
14
Circuit Description
1. Frequency Configuration
The receiver utilizes double conversion superheterodyne. The first IF is 38.85MHz and the second is
450KHz. The first local oscillator signal is supplied by the PLL circuit; and the second (38.4MHz) is
generated from the frequency tripling of TCXO (12.8MHz). The PLL circuit generates the frequencies
required for transmission. (See figure 1).
Frequency Range VHF: 136MHz—174MHz
UHF: 400MHz—470MHz
450MHz—520MHz
2. Receiver Circuit
The receiver circuit is shown as figure 1.
Figure 1 Receiver Circuit
2.1 High Frequency Bandpass Amplifier Circuit

It consists of RF amplifier (Q1201) and BPF. The range of bandpass frequency is the frequency range
of the radio itself. The signal is filtered by the BPF to eliminate unwanted signals before going to the
first mixer.
2.2 First Mixer
The signal from BPF is mixed with the first local oscillator signal from PLL circuit at the first mixer
(Q1203) to become a 38.85MHz first IF signal. The first IF signal is then fed through the crystal filter
(XF2200) to further remove spurious signals.
2.3 IF Amplifier
The first IF signal is amplified by Q2204 and then enters IC2202, where the signal is mixed again with
the second local oscillator signal (38.4MHz) to become a 450KHz second IF signal. The second IF
signal is then fed through a ceramic filter (N: CF2202; W: CF2203) to eliminate unwanted signals. The
resulting signal then is detected by IC2202 and output from Pin 9 as audio signals.
2.4 Audio Amplifier
The audio signal obtained from IC2202 is amplified and filtered by IC1402 before being amplified by
IC1401 (the received signalling is separated and input into CPU for decoding). The processed
signalling passes through Q1403 (AF MUTE) and is amplified by IC1405. The amplified signal is fed to
K301 controlling the volume on the front panel before entering audio amplifier (IC1511). The output
audio signal drives the speaker.
- 15 -
Circuit Description
2.5 Squelch Open

Part of the audio signals output from IC2202 passes through IC2202 Pin8 and is amplified by IC2202
again, then is filtered and rectified to produce an SQL level. The SQL level is compared with the existing
reference level in CPU (IC2502) to generate a level to control AF_mute and APCO, which determines
whether to output sounds from the speaker by controlling Q1403and IC1511.
3. Transmitter Circuit
The transmitter circuit is composed of the MIC circuit, modulation circuit, RF driver, final-stage power
amplification circuit and APC circuit.
Figure 2 Transmitter Circuit
3.1 MIC and Modulation Circuit

The audio signal from MIC is amplified by IC1407 before being pre-emphasized and encoded by IC1401.
The output audio signal is added into signalling and then is fed through VCO for modulation.
3.2 RF Driver and Final-Stage Power Amplification Circuit
The Tx-RF signal output from Q701 in the VCO circuit is amplified by Q703, drivers Q2102 and Q2101.
The amplified signal is then fed to IC2101 (final-stage amplifier) and passes through LPF before
reaching the antenna.
3.3 APC
The APC circuit stabilizes the output power at a predetermined level. D2107 and D1106 transform the
signal from the detector to DC voltage, which is then compared with the reference voltage from CPU in
IC1102 to output a DC voltage. The DC voltage controls the output power by controlling the grid of
IC2101.
4. PLL Circuit
The frequencies of receiving the first local oscillator signal and transmitting signal are generated by the
PLL circuit. The PLL circuit consists of Tx frequency oscillator (Q701), Rx frequency oscillator (Q702),
buffer amplifier (Q703), RF amplifier (Q708), PLL IC (IC2801), LPF and Tx/Rx VCO control switch (Q704,
Q706).
In transmit mode, IC2502 transmits the frequency data to PLL IC. Q704 is turned on to activate Tx VCO.
16
Circuit Description
The output signal is amplified by Q703 and Q104, and then divided by PLL IC into 2.5KHz, 5KHz or
6.25KHz signals. The divided signal is compared with the 2.5KHz, 5KHz or 6.25KHz reference signal
from a 12.8MHz crystal oscillator (2.5 PPM frequency stability) in the phase comparator. The frequency
control voltage output from the phase comparator is sent to Tx VCO after passing through LPF (Q2802,
Q2803). In the meantime, the modulation signal (Tx) is passed to Tx VCO for frequency modulation.
The working principle in receive mode is similar to that in transmit mode.
Figure 3
5. Control Circuit
The control circuit is composed of CPU, reset IC and power supply control circuit.
5.1 CPU
IC2502 (CPU) operates at 9.8304MHz. CPU controls the data transmission among EEPROM (IC2501),
Rx circuit, Tx circuit, control circuit, display circuit and peripheral circuits.
Figure 4 Control Circuit
17
Circuit Description
5.2 Power Supply

B+ supplies power for the radio. D1515 and D2516 are over-voltage protection diodes. Power-on/off
can be controlled via the software.
Figure 5 Power Supply Circuit
provides power for IC1601, IC1602 and IC2803, which produces 8V, 5V, 3V voltage for the circuit.
6. Display Circuit
The display circuit is comprised of CPU (IC2502), LCD, LED and other components. The radio can be
manually operated through P1 / P2 / P3 / P4 and ▲ / ▼ keys. Relevant channel information is
displayed on the 15-segment LCD in alphanumeric form.
Figure 6 Display Circuit
18
CPU PIN Function
：
PIN NO： Port Name PIN Name I/O Function
1 P94/DA1 APC/TV O RF Power control/Rx Sensitivity Output
2 P93/DA0 TONEO O DTMF/2-Tone/BEEP output
3 P92/TB2IN TONEI I 2-Tone decode pulse input
4 P91 AF_DIO I/O Baseband IC DATA I/O
5 P90 AF_SCLK O Baseband IC serial clock
6 BYTE BYTE I GND
7 CNVSS CNVSS I GND
8 P87/XCIN NC
9 P86/XCOUT SHIFT O Clock beat frequency On: H
10 RESET RESET I Reset
11 XOUT XOUT O Xtal
12 VSS GND I GND
13 XIN XIN I Xtal
14 VCC VCC I VCC
15 P85/NMI NMI I Pull UP
16 P84/INT2 AFRDF I Baseband IC MSK receive detect
17 P83/INT1 NC
18 P82/INT0 NC
19 P81 SWBC O Power switch contro，1 OFF，0 ON
20 P80 CTC_OUT O CTC _OUT (PWM) TO VCO
21 P77 AUX1 I/O (15pin ) AUX interface
22 P76/TA3O CTC_PLL O CTC_PLL (PWM)
23 P75 NC
24 P74/TA2O AF_DT O Baseband IC MSK serial data
25 P73 AF_CK I Baseband IC MSK serial clock
26 P72/TA1O AF_DIR O Baseband IC I/O control pin
27 P71/RxD2/TB5IN GPS_RXD I to GPS Module
28 P70/TxD2 GPS_TXD O to GPS Module
29 P67/TxD1 PTT/TXD O Serial data output PTT ON: L
30 P66/RxD1 HOOKOFF/RXD I Serial data input / Microphone HOOK input On: L
31 P65
32 P64
33 P63/TxD0 TXD0 O TO 15PIN Interface
34 P62/RxD0 RXD0 I TO 16PIN Interface
35 P61 NC
36 P60 NC
37 P57/RDY RDY I Pull UP
38 P56/ALE NC
39 P55/HOLD EPM I For Emulation
40 P54/HLDA FAN_C O Fan Control output
41 P53/BLCK DIR_5T O Reserved
42 P52/RD DIO_5T I/O Reserved
43 P51/BHE NC
44 P50/WR I For Emulation
45 P47/CS3 MICDAT I/O Microphone key code data input/output
46 P46/CS2 SLA_C I VOX earpiece Detect input
47 P45/CS1 LCD_SCL O LCD Driver CLK
48 P44/CS0 LCD_DA O LCD Driver DAT
49 P43/A19 LEDG O Green LED control: ON:H, off:L
50 P42/A18 LEDR O Red LED control: ON:H, off:L
51 P41/A17 LCD_LED O LCD background LED control: ON:H, off:L
52 P40/A16 P1_K I Programmble Function Key 1
56 P34/A12 DWN_K I Programmble Function Key Down
57 P33/A11 UP_K I Programmble Function Key Up
58 P32/A10 PWR_K I Power switchKey
- 19 -
CPU PIN Function
59 P31/A9 MIC_mute O Mic mute Mute: H

60 Vcc VCC I VCC
61 P30/A8 DTMF_ACK O DTMF IC
62 Vss GND I GND
63 P27/A7 DTMF_SD I DTMF IC
64 P26/A6 DTMF_EST I DTMF IC
65 P25/A5 HSET_C O Earpiece AF mute mute:L.
66 P24/A4 VOX_APCO O Earpiece PA mute mute:L.
67 P23/A3 NCON O RX W/N Band control W: H, N: L
68 P22/A2 WCON O TX W/N Band control W: H, N: L
69 P21/A1 PLL_LE O PLL IC
70 P20/A0 PLL_DT O PLL IC
71 P17/INT5 PLL_CK O PLL IC
72 P16/INT4 PLL_UL I PLL IC
73 P15/INT3 T/R_VCO O VCO T/R Toggle, Rx: L, Tx: H
74 P14 EESDA I/O E2 IC
75 P13 EESCL O E2 IC
76 P12 APCO O Speaker PA mute mute: L
77 P11 COR O COR Level Output (H/L programmble)
78 P10 AF_mute O RX Audio Mute, mute: H
79 P07/D7 IGN I Ignition sense input H: off L: on
80 P06/D6 SELF I Reset mode control
81 P05/D5 NC
82 P04/D4 NC
83 P03/D3 8TC O T8 Power control, 8T: H
84 P02/D2 NC
85 P01/D1 8RC O R8 Power control, 8R: H
86 P00/D0 NC
87 P107/AN7 NC
88 P106/AN6 NC
89 P105/AN5 VOX I VOX DET
90 P104/AN4 TEMP I Temperature detect input
91 P103/AN3 RSSI I RSSI input
92 P102/AN2 SQL I SQL signal input
93 P101/AN1 VSWR I VSWR detect input
94 AVSS GND I GND
95 P100/AN0 TI I CTCSS/CDCSS signal input
96 VREF VCC I
97 AVCC VCC I
98 P97 NC
99 P96 WDF O watch dog IC
100 P95 ALARM/AFCO I 15pin ALARM input ON: L
20
Terminal Function
1. Display Unit
Pin No. Name Description
J2301 (To MIC Jack)

1 8V 8V Power supply
2 Sla_En(CM) VOX earpiece Det input(Serial data input for the keypad
microphone).
3 HOOK/RxD Hook signal input/ Serial data input.
4 GND GND
5 MIC MIC signal input.
6 PTT/TxD PTT signal input/Serial data output.
7 MBL Backlight control signal. “H”: On, “L”: Off.
8 RX Audio Audio output for VOX earpiece
J2302 (To Tx/Rx Unit)

1 GPS_TXD Serial data output to GPS optional board.
2 LCD_LED LCD light control signal
3 GPS_RXD Serial data input from GPS optional board.
4 P1_K P1 Key on/off
5 GND Ground
7 R_LED RED light control
9 G_LED Green light control
11 LCD_SCL LCD driver IC
12 DWN_K Down key on/off
13 LCD_SDA LCD driver IC
14 UP_K UP key on/off
15 Sla_En(CM) VOX earpiece Det output(Serial data input for the keypad
microphone)
16 PWR_K Power switch key on/off
18 GND Ground
20 VLCI Audio output after volume adjustment
21 GND Ground
22 VLCO Audio input after volume adjustment
23 MIC MIC signal output.
24 GND Ground
25 RX Audio Audio input for VOX earpiece
26 GND Ground
27 NC
28 NC
29 5C 5V power supply
- 21 -
Terminal Function
2. Tx-Rx Unit
Pin No. Name Description
J502 (To Display Unit)

5 NC
6 NC
7 GND Ground
8 RX Audio Audio input for VOX earpiece
9 GND Ground
10 MIC MIC signal output.
11 VLCO Audio input after volume adjustment
12 GND Ground
13 VLCI Audio output after volume adjustment
15 GND Ground
17 PWR_K Power switch key on/off
18 Sla_En(CM) VOX earpiece Det output (Serial data input for the keypad
microphone)
19 UP_K UP key on/off
20 LCD_SDA LCD driver IC
21 DWN_K Down key on/off
22 LCD_SCL LCD driver IC
24 G_LED Green light control
26 R_LED RED light control
28 GND Ground
30 GPS_RXD Serial data input from GPS optional board.
31 LCD_LED LCD light control signal
32 GPS_TXD Serial data output to GPS optional board.
J504 (to Speaker)

1 SP1 BTL output for speaker.
2 SP2 BTL output for speaker.
J2503 (to Repeater)

1 GND Ground ( special for mic ground)
2 EXT_MIC_IN EXT_Microphone Audio input (80mV RMS @60% Deviation )
3 COR COR output ( H/L level programmable)
4 EXT_Alarm External Emergency logic input ( active :L)
5 BS 13.8V power supply
6 FLT_RX_Audio Discriminator Audio output (350mV RMS)
7 RX_AF_Output Line Audio Output （1000mV RMS）
8 FLT_Mod_IN Flat modulation input ( 150mV,RMS ctcss. 200mVp-p/CDCSS)
9 RXD0 Serial data input
10 TXD0 Serial data output
11 GND Ground
22
Terminal Function
12 NC
13 IGN Ignition sensor input
Expansion functions:
14 AUX1 1. Speaker Mute; 2. External Monitor; 3. ▲/▼ key 4. External
Hook; 5. MIC Mute;
15 EXT_PTT External PTT input
23
Tuning Description
I. Key Functions
1-1 Front Panel View
1 2 3 4
8 7 6 5
① Volume Control Knob
Rotate the knob clockwise to increase the volume and counterclockwise to decrease the
volume.
① LCD
Please refer to section LCD Display.
① Programmable Function Keys ▲ / ▼
Your local dealer can program these keys with various auxiliary functions.
Please refer to section Programmable Function Keys.
① LED Indicator
① Speaker
① Power Switch
① Programmable Function Keys P1 / P2 / P3 / P4
Your local dealer can programmed these keys with various auxiliary functions.
Please refer to section Programmable Function Keys.
① Microphone Jack
Plug the microphone into the jack.
Ⅱ Panel Tuning Mode
2-1 Basic Operations in Panel Tuning Mode

The transceiver is tuned in this mode. Operations are as follows:
1) Hold down P1 to power on the radio. The radio enters the tuning mode.
2) Use ▲ / ▼ to select setting items. Press P4 to enter the sub-item of the selected item.
3) Press P4 to enter the sub-item. Press ▲ / ▼ to tune the parameter. Press P4 again to save the tuned
data and move to next item, or press P1 to return to previous menu without saving the tuned data.
Note: Please do the model reset mode before enter panel tuning mode.
- 24 -
Tuning Descrptoin
2-2 the tuning item is as follong
No Tuning Item
1 Tx High Power
2 Tx Low Power
3 Maximum Deviation
4 CDCSS Balance
5 CTCSS Deviation (67.0Hz)
8 CDCSS Deviation
9 DTMF Deviation
10 MSK Deviation
11 Single Tone Deviation
12 Rx Sensitivity
13 Squelch Open 9
14 Squelch Open 3
15 Squelch Close 9
16 Squelch Close 3
2-3. Tuning Items and Display
Main LCD Wideband/

Setting Items Frequency Sub-LCD Description
Narrowband
High power
TxHIGH Low _L *** No signalling
Wideband
Tx Power High _H *** No signalling
Low power
Tx LOW Low _L *** No signalling
Wideband
Wideband Low _L *** No signalling
Max Deviation MAX.DEV Medium band Center M_C *** No signalling
Narrow band Low N_L *** No signalling
25
Tuning Descrptoin
Center _C *** 100Hz square wave

Wideband Low _L *** 100Hz square wave
CDCSS Balance CDCSS.BAL High _H *** 100Hz square wave
Medium band Center M_C *** 100Hz square wave
Narrow band Center N_C *** 100Hz square wave
CTC.DEV_L High _H *** CTCSS: 67.0Hz
Medium band Center M_C *** CTCSS: 67.0Hz
Narrow band Center N_C *** CTCSS: 67.0Hz
CTCSS.Deviation High _H *** CTCSS: 151.4Hz
CTC.DEV_M
Medium band Center N_C *** CTCSS: 151.4Hz
CTC.DEV_H High _H *** CTCSS: 254.1Hz
Medium band Center M_C *** CTCSS: 254.1Hz
Center _C *** CDCSS: 023N
Wideband Low _L *** CDCSS: 023N
CDCSS.Deviation CDCSS.DEV High _H *** CDCSS: 023N
Medium band Center M_C *** CDCSS: 023N
Narrow band Center N_C *** CDCSS: 023N
Center _C *** DTMF: 9
Wideband Low _L *** DTMF: 9
DTMF Deviation DTMF.DEV High _H *** DTMF: 9
Medium band Center M_C *** DTMF: 9
Narrow band Center N_C *** DTMF: 9
Center _C *** 0XAAAQ
Wideband Low _L *** 0XAAAQ
MSK Deviation MSK.DEV High _H *** 0XAAAQ
Medium band Center M_C *** 0XAAAQ
Narrow band Center N_C *** 0XAAAQ
Center _C *** 1KHz
Wideband Low 1KHz
_L ***
Single Tone Deviation TONE DEV High 1KHz
_H ***
Medium Center M_C *** 1KHz
Narrowband Center N_C *** 1KHz
26
Tuning Descrptoin
- Low No signalling, SQL off

_L ***
Low-medium No signalling, SQL off
-
SENSITVITY frequency _LC ***
Rx Sensitivity
TY - Center No signalling, SQL off
_C ***
- Medium-high _HC *** No signalling, SQL off
High _H *** No signalling, SQL off

OPENSQL SQL 9
9 Wideband
SQL 9
Narrowband
SQL Open
OPENSQL SQL 3
Low No signalling
3 Wideband _L ***
SQL 3
Narrowband
SQL 9
Wideband
CLOS.SQL
9
SQL 9
Narrowband
SQL Close Center _C *** No signalling
SQL 3 Low _L *** No signalling

Wideband High No signalling
_H ***
CLOS.SQL High _H *** No signalling
3 SQL 3 Medium Center M_C *** No signalling
SQL 3
Narrowband
27
Tuning Descrptoin
2-4. Flow Chart
The tuning flow chart is as following:
[P1]+Power ON
Tuning Mode
[▲] / [▼]
[P4] [P4]
Tx HIGH TX high power (Center) CDCSS deviation CDCSS deviation(Center)
[P4] [P4]
TX high power (Low) CDCSS deviation(Low)
[P4]
[P4]
CDCSS deviation(High)
TX high power (High)
[P4]
[P4] CDCSS deviation
[▲] / [▼] (Medium Center)
[P4]
Tx LOW TX low power (Center) [P4]
CDCSS deviation
[P4]
(Narrow Center)
TX low power (Low) [P4]
[P4] [▲] / [▼]
TX low power (High)
[P4] [P4]
[▲] / [▼]
[P4] DTMF deviation DTMF deviation(Center)
Max. deviation Max. deviation (Center)
[P4]
[P4]
Max. deviation (Low) DTMF deviation(Low)
[P4] [P4]
Max. deviation (High) DTMF deviation(High)
[P4]
[P4]
Max. deviation (Medium
Center) DTMF deviation (Medium)
[P4]
[P4]
Max. deviation (Narrow
Center) DTMF deviation (Narrow)
[P4]
Max. deviation (Narrow [P4]
Low) [▲] / [▼]
[P4] [P4]
Max. deviation (Narrow MSK deviation MSK deviation (Center)
High)
[P4] [P4]
[▲] / [▼] MSK deviation(Low)

[P4]
CDCSS Balance CDCSS Balance (Center) [P4]
[P4] MSK deviation(High)
CDCSS Balance(Low)
[P4]
[P4]
CDCSS Balance(High) MSK deviation (Medium)
[P4]
[P4]
CDCSS Balance (Medium
Center) MSK deviation (Narrow)
[P4]
CDCSS Balance (Narrow [P4]
Center) [▲] / [▼]
[P4]
[P4]
Single tone deviation
[▲] / [▼] [P4]
（Center）
CTCSS deviation(Center) [P4]
CTCSS deviation L/C/H
[P4]
CTCSS deviation(Low) Single tone deviation(Low)
[P4] [P4]
CTCSS deviation(High) Single tone
[P4] deviation(High)
CTCSS deviation [P4]
(Medium Center) [▲] / [▼]
[P4]
(Medium)
CTCSS deviation
(Narrow Center) Sensitivity [P4]
[P4] Single tone deviation
(Narrow)
[P4]
28
Tuning Descrptoin
[P4]
Sensitivity Rx Sensitivity (Low)
[P4]
Rx Sensitivity (CL)
[P4]
Rx Sensitivity (Center)
[P4]
Rx Sensitivity (HC)
[P4]
Rx Sensitivity (High)
[P4]
[▲] / [▼]
[P4]
Open Squelch 9/3 Open Squelch (Center)
[P4]
Oopen Squelch (Low)
[P4]
Open Squelch (High)
[P4]
Open Squelch (Medium
Center)
[P4]
Open Squelch (Narrow
Center)
[P4]
Low)
[P4]
High)
[P4]
[▲] / [▼]
[P4]
Close Squelch 9/3 Close Squelch (Center)
[P4]
Close Squelch (Low)
[P4]
Close Squelch (High)
[P4]
Close Squelch (Medium
Center)
[P4]
Close Squelch (Narrow
Center)
[P4]
Low)
[P4]
High)
[P4]
[▲] / [▼]
Tx HIGH
29
Tuning Descrptoin
Ⅱ. Tuning Method and Procedures:

1．Instrument:
Radio Communication Test Set 1 set
Spectrum Analyzer 1 set
20A/30V Power Supply 1 set
Digital Voltmeter 1 set
Power Meter 1 set
Test Cable 1 set
2．Tuning Procedures:
1. Initialization
It is necessary to set the frequency and initialize the radio before tuning because there is no required
information in EEPROM when the radio is manufactured.
Detail see the model set mode.
2. Tuning
Some items can be tuned in the conventional mode and the others can be tuned manually.
VCO
Measurement Tuning
Item Condition Specification/Remarks
Test Instrument Terminal Parts Method
1.CH: Tx HI QM-790 U1
5. V±0.1V QM-790 U2
2. VCO Lock
Digital Voltmeter CV TC701 QM-790 V
Voltage (Tx )
2.CH: Tx LO Check ＞1.0V
QM-790 U1
1.CH: Rx HI 5.0V±0.1V QM-790 V
3. VCO Lock Digital
CV TC702 QM-790 U2
Voltage (Rx) Voltmeter
2.CH: Rx LO Check ＞1.0V
30
Tuning Descrptoin
Transmitter
Measurement Tuning
Specification
Item Condition
Termina /Remarks
Test Instrument Part
l Method
Radio
4. Tx Not enter the tuning item,
Communication ANT Tune VR1801 Tune channel frequency Error<50Hz
Frequency but switch to CH_4
Test Set
Each channel High Power:

Tune software Check High
corresponds to a specific PO=43~45W Power
Radio setting. Press
Tx frequency. Enter items I≤11.0A
5. Tx Communication P4 to save the
“TxHIGH”, “Tx LOW” in ANT
Power Test Set setting and
turn and press P4 to enter Low Power:
Ammeter move to the Check Low
“_C”, “_L” and “_H” PO=23~25W Power
next item.
to tune high/low power. I≤7.0A
Check the deviation of Wideband:

H/M/L channel: “_C”, “_L”,
4.0±0.1KHz(W) and “_H”
Each channel
Radio Tune software
corresponds to a specific
Communication setting. Press Check the deviation of
Tx frequency. Enter item ANT Medium
6. Max. Test Set P4 to save the H/M/L channel:
“MAX.DEV” and tune MIC band: “M_C”
Deviation Filter: setting and
“_C”, “_L”, “_H”, Jack 3.2±0.1KHz(M)
0.05-15KHz move to the
“M_C”, “N_C”, "N_L"
AF: 1KHz 75mV next item.
and "N_H".
Check the deviation of Narrow band:
“N_C”, “N_L”
H/M/L channel: and “N_H”
1. 9±0.1KHz (N)
Radio Check deviation:

7.
Communication 2.7KHz-3.4KHz (W)
Modulation
2.2KHz-2.7KHz (M)
Sensitivity Each channel Test Set ANT
corresponds to a specific Filter: MIC 1.3KHz-1.7KHz (N) Check
Tx frequency. 0.05-15KHz Jack
AF: 1KHz
8. 7.5mV
Modulation ≤5%
Distortion
“_C”, “_L”
and “_H”
are
wideband of
center, low
and high
Each channel Radio Use ▲ / ▼ key
frequencies
corresponds to a specific Communication to tune software
“M_C” is
9. CDCSS Tx frequency. Enter item Test Set setting. Press
ANT medium band
Balance “CDCSS.BAL” and press Filter P4 to save and
(20K) of
P4 to enter “_C”, “_L”, <20HZ-300Hz move to the
center
“_H”, “M_C” and “N_C”. AF: OFF next item.
frequency.
“N_C” is
narrow band
(12.5K) of
center
frequency.
31
Tuning Descrptoin
“_C”, “_L”
Each channel and “_H”
corresponds to a specific are wideband
Tx frequency. Enter items Radio Use ▲ / ▼ key of each
“CTCL_DEV”, Communication to tune software Tune deviation to frequency.
10. CTCSS “CTCC_DEV ” and Test Set setting. Press 0.75KHz±0.10KHz (W) M_C” is
ANT
Deviation “ CTCH_DEV”. Tune Filter P4 to save and 0.60KHz±0.10KHz (M) medium
67Hz/151.4Hz/254.1HzC <20HZ-300Hz move to the 0.37KHz±0.05KHz (N) band. N_C” is
TCSS. Press P4 to enter AF: OFF next item. narrow band
“_C”, “_L”, “_H”, “M_C of center
“ and “N_C”. frequency.
Each channel
Radio Use ▲ / ▼ key
corresponds to a specific
Communication to tune software Tuning deviation to
Tx frequency. Enter
11. CDCSS Test Set setting. Press 0.75KHz±0.10KHz (W) Same as
item “CDCSS.DEV” and ANT
Deviation Filter P4 to save and 0.60KHz±0.10KHz (M) above
press P4 to enter “_C”,
<20HZ-300Hz move to the 0.37KHz±0.05KHz (N)
“_L”, “_H”, “M_C” and
AF: OFF next item.
“N_C”.
Use ▲ / ▼ key “_C”, “_L”

to tune software and “_H”
setting. Press are wideband
Each channel Radio P4 to save and of each
corresponds to a specific Communication move to the frequency.
3.0KHz±0.1KHz (W)
12.DTMF Tx frequency. Enter item Test Set next item. “M_C” is
ANT 2.4KHz±0.1KHz (M)
Deviation “DTMF.DEV” and press Filter medium
1.5KHz±0.1KHz (N)
P4 to enter “_C”, “_L”, 300HZ--3KHz band. “N_C”
“_H”, “M_C” and “N_C”. AF: OFF is narrow
band of
center
frequency.
Use ▲ / ▼ key “_C”, “_L”
to tune software and “_H”
setting. Press are wideband
Each channel Radio P4 to save and of each
corresponds to a specific Communication move to the frequency.
3.0KHz±0.1KHz (W)
Tx frequency. Enter item Test Set next item. “M_C” is
13. MSK ANT 2.4KHz±0.1KHz (M)
“MSK.DEV” and press P4 Filter medium
1.5KHz±0.1KHz (N)
to enter “_C”, “_L”, 300HZ--3KHz band. “N_C”
“_H”, “M_C” and “N_C”. AF: OFF is narrow
band of
center
frequency.
“_C”, “_L”
and “_H”
are wideband
Each channel Radio Use ▲ / ▼ key of each
14. Single corresponds to a specific Communication to tune software Tuning deviation to frequency.
tone Tx frequency. Enter item Test Set setting. Press 3.0KHz±0.10KHz (W) “M_C” is
ANT
(2-Tone/5-T “TONE DEV” and press Filter P4 to save and 2.4KHz±0.10KHz (M) medium
one) P4 to enter “_C”, “_L”, 300HZ--3KHz move to the 1.5KHz±0.1KHz (N) band. “ N_C”
“_H”, “M_C” and “N_C”. AF: OFF next item. is narrow
band of
center
frequency.
Radio
Communication
Test Set
Each channel
Filter S/N≥45(W)
15. Tx S/N corresponds to a specific ANT Check
0.3-3KHz S/N≥40(N)
Tx frequency.
AF: 1KHz
7.5Mv
DEV: 3KHz
32
Tuning Descrptoin
Receiver
Measurement Tuning Specification/

Item Condition
Remarks
Test Instrument Terminal Parts Method
UHF:
Use ▲ / ▼ Set the gain value

to tune the to the max. The
Enter item “SENSITVITY”. parameter. corresponding
Each channel corresponds to Press P4 frequency of VHF
16. RF
a specific Tx frequency. Scanner ANT to save the and UHF is on the
bandpass filter
Press P4 to enter _L”, ”LC”, setting and leftmost and VHF:
“_C”, “_CH” and “_H” move to rightmost of the
the next bandpass wave.
item. Press P4 to save.
Radio
Communication
Test Set
Frequency: Rx Center is SSG Output:
17. Max. tuned to CH1(C) and -47dBm ANT
Volume corresponds to a specific MOD: 1KHz SP Jack K301 Check max.
volume: 5.1V
frequency. DEV: ±3KHz(W)
±1.5KHz(N)
Filter:
0.3-3.0KHz
1. Test Mode, CH: Rx Center,

manually tuned to CH_1(C).
Radio W/N
Communication switch
Test Set (Power on
SSG Output: the radio
Tune K301. The
18. Sensitivity -118dBm ANT while SINAD:
2. Test Mode, CH: Rx LO, volume is rated
MOD: 1KHz SP Jack holding 12dB or above
manually tuned to CH_2(L). output.
DEV: ±3KHz(W) down P1 to
±2.4KHz(M) enter the
±1.5KHz(N) channel
Filter: 0.3-3.0KHz set mode.)
3. Test Mode, CH: Rx HI,

manually tuned to CH_3(H)
33
Tuning Descrptoin
Radio Press P3 and

Communication P4 respectively
Enter OPENSQL9 (Level 9 Test Set to read/write
No need to tune
on) and OPENSQL3” (Level SSG Output: SQL level
software setting at
3 on) in turn. Press P4 to -120dBm (Level 3) from/into CPU.
19. SQLOpen SQL Level 3/9.
enter “_C”, “_L”, “_H”, (Note: Do not
Press P3 and P4 to
“M_C”, “N_C” , “N_L” and press P4 until
SSG Output: save.
“N_H”. LED glows
-114dBm (Level 9)
green after P3
is pressed.
Tune
Radio ANT Press P3 and
software
Communication SP Jack P4
setting
Test Set respectively to
Enter CLOS.SQL9 (Level 9 SSG Output: read/write
No need to tune
off) and CLOS.SQL3” (Level -122dBm (Level 3) SQL level
software setting at
3 off) in turn. Press P4 to from/into
20. SQLClose SQL Level 3/9.
enter “_C”, “_L”, “_H”, CPU. (Note:
Press P3 and P4 to
“M_C”, “N_C” , “N_L” and Do not press
SSG Output: save.
“N_H”. P4 until LED
-116dBm (Level 9)
glows green
after P3 is
pressed.
Radio
20. Distortion DIS≤5%
Communication Filter:
1. Test Mode, Channel: Rx ANT
Test Set 0.3-3.0KH Check
Center SP Jack S/N≥45 (W)
21. S/N SSG Output: z
S/N≥40 (N)
-60dBm
Note: The radio must be covered with aluminum chassis during the tuning of sensitivity, Tx power,
signalling waveform, deviation, Rx Squelch. Connect an RF power meter to the antenna connector
during transmission. Connect the SINAD meter with 16ohm load to the external speaker jack.
34
Troubleshooting Flow Chart
- 35 -
MCU
Check
Normal Power- on Yes RF circuit can’t Check the

alert tone? be driven control circuit
No
Speaker works No Replace the

well? speaker
Yes
9. 8304 MHz works Yes Read available No Check read

normally? or not? circuit
`
Yes
Reset
Yes
Pin 10 is of No
Check5V
high level?
Yes
MCU works well
36
No output
power
Yes Power supply NO Check power

works well ? supply circuit
Yes The current is NO Check RF PA VGG drain NO Check VGG

normal ? voltage is supply circuit
normal ?
Check D 2101
Check drive
& low pass
stage
network
Repair the Yes

Driver stage is VCO
transmission
normal ? Check flow chart
network
NO
NO
Normal power ? Check the
suited network
Yes
Finished Yes
Normal power ?
Finished NO
Replace
Q 2101
Yes Normal power ?
NO
Finished
Replace Q 2101
37
No receive
Power supply of AF NO Check power

IC 1511 is normal? Supply circuit
Yes
Normal base NO Input of base band Yes

Check IC1401
Band IC output? IC is normal?
NO
Yes
Otput of IC2202 is Yes Check IC1402
Normal?
Check volume
Switch and speaker NO
The second local NO

Check Q1205
Oscillator is normal?
Yes
Normal CD2201 NO
Voltage? Replace CD2201
Yes
Yes Check IC 2202

IC 2202 inputs ?
status
NO
T 1 outputs in RF Yes
Input? Check VCO
NO
Check Q 1201 passage
38
Disassembly and Assembly for Repair

Disassembly
1. Power off the radio. Disconnect the power cord and screw out the antenna connector.
2. Loosen the 5 screws locking the cover and pedestal of the aluminum chassis.
3. Remove the top cover.
4. Loosen the two screws shown in the following figure, and detach the front panel from the main unit.
5. Pull out the volume control knob. Screw out the copper nut from the potentiometer tuning volume.
Then loosen the three screws fixing the front case and remove the front panel.
- 39 -
Disassembly and Assembly
6. Use an electric iron and screwdriver to separate the antenna connector, power cord, external board.
7. Loosen the screws fixing the main unit PCB and PA module.
Assembly
1. Fix the bracket (main unit) using four self-tapping screws.
40
Disassembly and Assembly
2. Tighten the four tuning screws (each with one shrapnel and one shim).
3. Plug the connector (microphone) into the jack (microphone). If the microphone is not in use, hang
it on the bracket .
41
Exploded View
33 32 31 30 29 28 27 26
25
24
23
22
39 38 37 36 35 34 21
20
40
41
42
43
44
45 19
46
18
47
48
17
49
16
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15
- 42 -
QM-790 Mechanical Parts List
No. Material No. Description Qty.
1 5079001000 Volume knob 1
2 5279001000 Knob Inner liner 1
3 6279001000 Volume switch Fixing nut 1
4 5079008000 LCD glass 1
5 6579001000 LCD 3M tape 1
6 5179001000 Panel Silica key 1
7 5079007000 PMCC light guide 1
8 6579002000 Light 3M tape 1
9 7679001010 Logo Label 1
10 6103006120 Panel fixing screw 2
11 5079002000 Front panel 1
12 6479001000 Speaker waterproof cloth 1
13 4279016050 speaker 1
14 4379002000 Speaker plug 1
15 6103018120 Top cover srew 5
16 6479002010 Front panel waterproof poron 1
17 6103010110 RF PA screw 2
18 3179210010 RF PA Module 1
19 4679001000 Mini-UHF antenna pedestal 1
20 6103006110 Antenna screw 2
21 6113001110 Antenna screw liner 2
22 5279002010 Power wire fixing part 2
23 4379001000 Power cord module 2
24 P10A51U00C PCB board 1
25 6103006010 PCB fixing screw 17
26 6479003010 Waterproof poron 2+2
27 5379002000 Top cover 1
28 6102505120 Screw(power wire fixing part) 4
29 6479004010 Speker jack poron 1
30 6102504110 Screw (GPS antenna pedestal ) 4
31 4679002010 GPS antenna pedestal 1
32 5179003000 Audio PA heat-dissipation cushion 1
33 5379001000 Aluminum chassis base 1
34 6102308010 Screw (front panel PCB) 3
35 4379003000 32PIN FFC 1
36 6103006110 Screw (GPS PCB) 4
37 P40A62001C GPS PCB 1
38 5179004000 LCD conductive rubber connector 1
39 5079009000 PMCC bracket 1
40 P30A61001C Front panel PCB 1
41 5079010000 light-guide module 1
42
43
44
45 6679001000 LCD 1
46 5279003000 LCD bracket 1
47 4005030010 Volume rotary switch 1
48 4479001000 Microphone Jack 1
49 6479005010 LCD poron 1
43
QM-790 PCB View

QM-790-U Main PCB TOP Layer
QM-790 PCB View
QM-790-U Main PCB Bottom Layer
45
QM-790 PCB View
QM-790-U VCO PCB Bottom Layer
46
QM-790 PCB View
QM-790-V Main PCB TOP Layer
47
QM-790 PCB View
QM-790-V Main PCB Bottom Layer
48
QM-790 PCB View
QM-790-V VCO PCB Bottom Layer
49
QM-790 PCB View
QM-790 Display PCB Top Layer
50
QM-790 PCB View
QM-790 Display PCB Bottom Layer
51
QM-790 Electronic Parts List
Main Board Unit

QM-790-U1 （400-470MHz）
）
No. Material No. Material Name Ref.No. Qty. Note
1 1501060590 Chip capacitor 0603 0.5PF B 50V C1133 1
3 1501044710 Chip capacitor 0402 470PF J 50V C1135 1
7 1501044730 Chip capacitor 0402 0.047UF K 25V C1141 1
8 1501041020 Chip capacito 0402 1000PF K 50V C1142 1
9 1501042240 Chip capacitor 0402 0.22UF Z 25V C1147 1
11 1701082250 Ta-capacitor 0805 2.2UF M 10V C1149 1
13 1701081050 Ta-capacitor 0805 1UF M 16V C1151 1
14 1501041020 Chip capacitor 0402 1000PF K 50V C1152 1
17 1501040500 Chip capacitor 0402 5PF B 50V C1205 1
- 52 -
53
64 1501042250 Chip capacitor 0402 2.2UF K 6.3V C1404 1
67 1501041050 Chip capacitor 0402 1UF K 6.3V C1408 1
74 1501042220 Chip capacitor 0402 2200pF K 50V C1416 1

54
No.
87 1701081060 Ta-capacitor 0805 10UF M 6.3V C1429 1
93 1101043340 Chip resistor 0402 330KΩ J 1/16W C1436 1
55

56

57

191 1501121590 Chip capacitor 501R18N1R5CV4E C2101 1
196 1501124710 Chip capacitor 631R18N471KV4E C2106 1
58

220 1501124710 Chip capacitor 631R18N471KV4E C2146 1
241 1101044720 Chip resistor 0402 4.7KΩ J 1/16W C2261 1
59

290 CF21990020 Ceramic filter 450KHz±4KH CD2201 1
60

291 CF21990010 Ceramic filter 450KHz±4.5KHz CF2202 1
292 CF21990030 Ceramic filter 450KHz±6KHz CF2203 1
293 1161041020 Array resistor 0402 1K*4 J 1/16 CP2501 1
297 D101040270 MA3J74200L D1106 1
298 D101040270 MA3J74200L D1107 1
299 D101040240 1SS355 D1108 1
300 D201050020 50BTRF-E D1202 1
301 D201050020 50BTRF-E D1203 1
302 D401050010 HSM88ASTL-E D1204 1
303 D201050020 50BTRF-E D1205 1
304 D201050020 50BTRF-E D1206 1
305 D101030020 S07700L D1209 1
306 D401040040 RB706F-40 D1401 1
307 D401040040 RB706F-40 D1403 1
308 D101040250 DSM3MA1TRF-E D1515 1
309 D101040280 P1250 3*2mm D2101 1
310 D101040230 UDZSTE(175.1B) 5 D2102 1
311 D101040270 MA3J74200L D2103 1
312 D101040240 1SS355 D2104 1
313 D101030020 S07700L D2105 1
314 D101040230 UDZSTE(175.1B) 5 D2119 1
315 D101040280 P1250 3*2mm D2201 1
316 D101040010 DAN222(TL) D2207 1
317 D101040010 DAN222(TL) D2208 1
318 D101040240 1SS355 D2511 1
319 D101040210 UDZSTE(1718B)18V D2512 1
320 D101040240 1SS355 D2513 1
321 D101040220 UDZSTE(1710B)10V D2514 1
322 1302992200 ERZV10D220 D2516 1
323 D101040240 1SS355 D2517 1
324 D101040200 UDZSTE(1715B)15V D2518 1
325 D101030030 S11100L D2801 1
326 D101040260 5ALL D2802 1
61

327 1101080000 Chip resistor 0805 0Ω J 1/8W F2501 1
328 3061130010 04M IC1102 1
329 3061130010 04M IC1103 1
330 3021040010 46-E2 IC1401 1
331 3061020010 51FU IC1402 1
332 3061020010 51FU IC1403 1
333 3061020010 51FU IC1404 1
334 3061020010 51FU IC1405 1
335 3061020010 51FU IC1407 1
336 3151180010 72FS SSOP IC1504 1
337 3031120030 3544 IC1510 1
338 3031120020 97D IC1511 1
339 3081110010 TA7808S IC1601 1
340 3081110010 TA7805F(TE16L.F IC1602 1
341 3081110010 XC6201P502PR IC1603 1
342 C110128900 12.8MHz IC1802 1
343 3179210010 4047M1 IC2101 1
344 3041020010 TA31136FNG IC2202 1
345 3071080010 24C256WI 256K IC2501 1
346 3011090010 M30GP IC2502 1
347 3121190020 13LESA 4.65V IC2503 1
348 3160200010 13BF(EL,N,F IC2512 1
349 3051150020 MB15 IC2801 1
350 3081110020 XC6201P302PR IC2803 1
351 4001021010 2PIN socket connector J2503 1
352 4003151010 15PIN connector J2503 1
353 4462990010 SPK JACK J501 1
354 4411032010 32PIN socket connector J502 1
355 2301320050 Coil E2-0.30*1.2*5TL L1202 1
356 2301320050 Coil E2-0.30*1.2*5TL L1203 1
357 2001062240 Multilayer inductor 0603 220nH L1204 1
359 2101082230 inductor 0805 22nH L1207 1
360 2301320050 Coil E2-0.30*1.2*5TL L1208 1
361 2301320050 Coil E2-0.30*1.2*5TL L1209 1
62

365 2201042210 Chip ferrite bead 0402 220Ω L1213 1
371 2001061050 Multilayer inductor 0603 1UH L1802 1
372 2301084110 Coil 0.8*3.0*11TR L2101 1
373 2301133030 Coil 1.3*2.8*3TR L2102 1
374 2301133030 Coil 1.3*2.8*3TR L2103 1
375 1501124710 Chip capacitor 631R18N471KV4E L2105 1
378 2201086000 Chip ferrite bead 0805 60Ω±25% L2108 1
379 2001101020 Multilayer inductor NLV25T-010J 10nH L2110 1
380 2001101020 Multilayer inductor NLV25T-010J 10nH L2111 1
381 2301084060 Coil 0.8*3.0*6TR L2112 1
382 2301133030 Coil 1.3*2.8*3TR L2201 1
383 2001101030 Multilayer inductor NLV25T-100J-PF L2214 1
385 1101040000 Chip resistor 0402 0Ω J 1/16W L2502 1
391 T101100010 511-TR1G Q1201 1
392 F101050010 YB-TL-E-Q Q1203 1
393 T101020010 2SC5108-Y Q1205 1
394 F101010020 1824-T1-A Q1402 1
395 F101010020 1824-T1-A Q1403 1
396 T101020030 2SC4116-GR Q1404 1
397 F101010020 1824-T1-A Q1521 1
63
No. Material No. Material

Material Name Ref.No. Qty. Note
398 T101040310 1132FD5T100R PNP Q1601 1
399 T101040050 DTC114EE(TL) Q1602 1
400 T101040310 1132FD5T100R PNP Q1603 1
401 T101040050 DTC114EE(TL) Q1604 1
402 T101040320 T1-A-RF NP Q2101 1
403 T101040320 T1-A-RF NP Q2102 1
404 T101020020 2SC4738GR Q2103 1
405 T101020010 2SC5108-Y Q2204 1
406 T101040010 DTA114EE(TL) Q2206 1
407 T101040010 DTA114EE(TL) Q2207 1
408 T101040050 DTC114EE(TL) Q2500 1
409 T101040010 DTA114EE(TL) Q2501 1
410 F101010020 1824-T1-A Q2502 1
411 T101040050 DTC114EE(TL) Q2503 1
412 T101040050 DTC114EE(TL) Q2505 1
413 T101040050 DTC114EE(TL) Q2507 1
414 T101040050 DTC114EE(TL) Q2509 1
415 T101020020 2SC4738GR Q2510 1
416 T101040330 506STR-E Q2512 1
417 T101040050 DTC114EE(TL) Q2513 1
418 T101040010 DTA114EE(TL) Q2514 1
419 T101040050 DTC114EE(TL) Q2515 1
420 T101040010 DTA114EE(TL) Q2516 1
421 T101040050 DTC114EE(TL) Q2517 1
422 T101040050 DTC114EE(TL) Q2518 1
423 T101040010 DTA114EE(TL) Q2519 1
424 T101040010 DTA114EE(TL) Q2520 1
425 T101040050 DTC114EE(TL) Q2801 1
426 T101040300 2SA1832-GR(TE85L.F Q2802 1
427 T101020020 2SC4738GR Q2803 1
428 1101042230 Chip resistor 0402 22KΩ J 1/16W R1120 1
64

437 1101040000 Chip resistor 0402 0Ω J 1/16W R1130 1
446 1101044720 Chip resistor 0402 4.7KΩ J 1/16W R1203 1
449 1101042790 Chip resistor 0402 2.7Ω J 1/16W R1206 1
65

491 1101041050 Chip resistor 0402 1MΩ J 1/16W R1431 1
503 1101049130 Chip resistor 0402 91KΩ F 1/16W R1443 1
66

67

68

69
No. Material No. Material

Material Name Ref.No. Qty. Note
622 1501041020 Chip capacitor 0402 1000PF K 50V R2246 1
70

71

705 1101061530 Thermister 0603 47KΩ J 1/10W TH1101 1
706 1501042250 Chip capacitor 0402 2.2UF K 6.3V VR1401 1
707 1401996830 Trimmer resistor 68KΩ(+25%) VR1801 1
708 C101990010 crystal 3.6864MHz X1402 1
709 C101990100 crystal 4.19MHz X1501 1
710 C101990030 crystal 9.8304MHz X2502 1
711 CF01990020 38.850MHz crystal filter XF2200 1
712 D301040010 18S02015 ZR2500 1
713 D301040010 18S02015 ZR2501 1
714 D301040010 18S02015 ZR2502 1
715 D301040010 18S02015 ZR2503 1
716 D301040010 18S02015 ZR2504 1
72

717 D301040010 18S02015 ZR2505 1
718 D301040010 18S02015 ZR2510 1
719 D301040010 18S02015 ZR2512 1
720 D301040010 18S02015 ZR2513 1
721 D301040010 18S02015 ZR2514 1
722 D301040010 18S02015 ZR2515 1
73
QM-790-V （136MHz-174MHz）
）
1 1501060590 Chip capacito 0603 0.5PF B 50V C1133 1
3 1501044710 Chip capacito 0402 470PF J 50V C1135 1
7 1501044730 Chip capacito 0402 0.047UF K 25V C1141 1
9 1501042240 Chip capacito 0402 0.22UF Z 25V C1147 1
17 1501040800 Chip capacito 0402 8PF B 50V C1205 1
74

75

73 1501042250 Chip capacito 0402 2.2UF K 6.3V C1404 1
76 1501041050 Chip capacito 0402 1UF K 6.3V C1408 1
83 1501042220 Chip capacito 0402 2200pF K 50V C1416 1
76

102 1101043340 Chip resistor 0402 330KΩ J 1/16W C1436 1
77

78

79

204 1501121500 Chip capacito 1206 15P J 250V C2101 1
205 1501120600 Chip capacito 1206 6P C 250V C2102 1
207 1501120600 Chip capacito 1206 6P C 250V C2104 1
209 1501121020 Chip capacito 1206 1000P K 250V C2106 1
237 1501121020 Chip capacito 1206 1000P K 250V C2146 1
80
No. Material No. Material Name Ref.No. Qty.

Qty. Note
258 1101044720 Chip resistor 0402 4.7KΩ J 1/16W C2261 1
81

307 CF21990020 Ceramic filter 450KHz±4KH CD2201 1
308 CF21990010 Ceramic filter 450KHz±4.5KHz CF2202 1
309 CF21990030 Ceramic filter 450KHz±6KHz CF2203 1
314 D101040270 MA3J74200L D1106 1
82

315 D101040270 MA3J74200L D1107 1
316 D101040240 1SS355(TE17) D1108 1
317 D201050060 62TRF-E D1202 1
318 D201050020 50BTRF-E D1203 1
319 D401050010 HSM88ASTL-E D1204 1
320 D201050060 62TRF-E D1205 1
321 D201050060 62TRF-E D1206 1
322 D101030020 MA2S07700L D1209 1
323 D401040040 RB706F-40 D1401 1
324 D401040040 RB706F-40 D1403 1
325 D101040250 DSM3MA1TRF-E D1515 1
326 D101040280 P1250 3*2mm D2101 1
327 D101040230 UDZSTE(175.1B) 5 D2102 1
328 D101040270 MA3J74200L D2103 1
329 D101040240 1SS355(TE17) D2104 1
330 D101030020 S07700L D2105 1
331 D101040230 UDZSTE(175.1B) 5 D2119 1
332 D101040280 P1250 3*2mm D2201 1
333 D101040010 DAN222(TL) D2207 1
334 D101040010 DAN222(TL) D2208 1
335 D101030030 S11100L D2501 1
336 D101040240 1SS355(TE17) D2511 1
337 D101040210 UDZSTE(1718B)18V D2512 1
338 D101040240 1SS355(TE17) D2513 1
339 D101040220 UDZSTE(1710B)10V D2514 1
340 1302992200 ZNR ERZV10D471 D2516 1
341 D101040240 1SS355(TE17) D2517 1
342 D101040200 UDZSTE(1715B)15V D2518 1
343 D101030030 S11100L D2801 1
344 D101040260 5ALL D2802 1
346 3061130010 04M IC1102 1
347 3061130010 04M IC1103 1
348 3021040010 46-E2 IC1401 1
349 3061020010 51FU IC1402 1
350 3061020010 51FU IC1403 1
351 3061020010 51FU IC1404 1
83

352 3061020010 51FU IC1405 1
353 3061020010 51FU IC1407 1
354 3151180010 72FS IC1504 1
355 3031120030 3544 IC1510 1
356 3031120020 97D IC1511 1
357 3081110010 TA7808S IC1601 1
358 3081110010 TA7805F(TE16L.F IC1602 1
359 3081110010 XC6201P502PR IC1603 1
360 C110128900 TCXO 12.8MHz IC1802 1
361 3179210020 1317M1 IC2101 1
362 3041020010 TA31136FNG IC2202 1
363 3071080010 24C256WI 256K IC2501 1
364 3011090010 M30GP IC2502 1
365 3121190020 13LESA 4.65V IC2503 1
366 3160200010 13BF(EL,N,F IC2512 1
367 3051150020 MB15 IC2801 1
368 3081110020 XC6201P302PR IC2803 1
369 4001021010 2PIN J2503 1
370 4003151010 15PIN connector J2503 1
371 4462990010 SPK JACK J501 1
372 4411032010 32PIN J502 1
373 2301320050 Coil E2-0.30*1.2*5TL L1202 1
374 2301320050 Coil E2-0.30*1.2*5TL L1203 1
376 2101061510 inductor 0603 15nH L1207 1
377 2301320050 Coil E2-0.30*1.2*5TL L1208 1
378 2301320050 Coil E2-0.30*1.2*5TL L1209 1
84

390 2301084110 Coil 0.8*3.0*11TR L2101 1
391 2301133050 Coil 1.3*2.8*5TR L2102 1
392 2301133050 Coil 1.3*2.8*5TR L2103 1
393 2301133050 Coil 1.3*2.8*5TR L2104 1
394 2301133050 Coil 1.3*2.8*5TR L2105 1
395 2201126000 Chip ferrite beadBLM41PG600SN1 L2106 1
396 2201126000 Chip ferrite bead BLM41PG600SN1 L2107 1
397 2201086000 Chip ferrite bead BLM18AG600SN1 L2108 1
398 2001106820 Multilayer inductor NLV25T-068J L2110 1
400 2301084060 Coil 0.8*3.0*6TR L2112 1
401 2301133050 Coil 1.3*2.8*5TR L2201 1
410 T101100010 AT-TR1G Q1201 1
411 F101050010 YB-TL-E-Q Q1203 1
412 T101020010 2SC5108-Y Q1205 1
413 F101010020 1824-T1-A Q1402 1
414 F101010020 1824-T1-A Q1403 1
415 T101020030 2SC4116-GR Q1404 1
416 F101010020 1824-T1-A Q1521 1
417 T101040310 1132FD5T100R PNP Q1601 1
418 T101040050 DTC114EE(TL) Q1602 1
419 T101040310 1132FD5T100R PNP Q1603 1
420 T101040050 DTC114EE(TL) Q1604 1
421 T101040320 T1-A-RF NP Q2101 1
422 T101040320 T1-A-RF NP Q2102 1
423 T101020020 2SC4738GR Q2103 1
424 T101020010 2SC5108-Y Q2204 1
425 T101040010 DTA114EE(TL) Q2206 1
85

426 T101040010 DTA114EE(TL) Q2207 1
427 T101040050 DTC114EE(TL) Q2500 1
428 T101040010 DTA114EE(TL) Q2501 1
429 F101010020 1824-T1-A Q2502 1
430 T101040050 DTC114EE(TL) Q2503 1
431 T101040050 DTC114EE(TL) Q2505 1
432 T101040050 DTC114EE(TL) Q2507 1
433 T101040050 DTC114EE(TL) Q2509 1
434 T101020020 2SC4738GR Q2510 1
435 T101040330 506STR-E Q2512 1
436 T101040050 DTC114EE(TL) Q2513 1
437 T101040010 DTA114EE(TL) Q2514 1
438 T101040050 DTC114EE(TL) Q2515 1
439 T101040010 DTA114EE(TL) Q2516 1
440 T101040050 DTC114EE(TL) Q2517 1
441 T101040050 DTC114EE(TL) Q2518 1
442 T101040010 DTA114EE(TL) Q2519 1
443 T101040010 DTA114EE(TL) Q2520 1
444 T101040050 DTC114EE(TL) Q2801 1
445 T101040300 2SA1832-GR Q2802 1
446 T101020020 2SC4738GR Q2803 1
86

87

88

89

90
No. Material No.

No. Material Name Ref.No. Qty. Note
644 1501041020 Chip capacito 0402 1000PF K 50V R2246 1
91

92

93

727 1101061530 Thermister 0603 47KΩ J 1/10W TH1101 1
728 1501042250 Chip capacito 0402 2.2UF K 6.3V VR1401 1
729 1401996830 Trimmer resistor 68KΩ VR1801 1
730 C101990010 crystal 3.6864MHz X1402 1
731 C101990100 crystal 4.19MHz X1501 1
732 C101990030 crystal 9.8304MHz X2502 1
733 CF01990020 crystal filter 38.850MHz XF2200 1
734 D301040010 18S02015 ZR2500 1
735 D301040010 18S02015 ZR2501 1
736 D301040010 18S02015 ZR2502 1
737 D301040010 18S02015 ZR2503 1
738 D301040010 18S02015 ZR2504 1
739 D301040010 18S02015 ZR2505 1
740 D301040010 18S02015 ZR2506 1
741 D301040010 18S02015 ZR2509 1
742 D301040010 18S02015 ZR2510 1
743 D301040010 18S02015 ZR2511 1
744 D301040010 18S02015 ZR2512 1
745 D301040010 18S02015 ZR2513 1
746 D301040010 18S02015 ZR2514 1
747 D301040010 18S02015 ZR2515 1
94
VCO Board Unit
QM-790-U1 （400-470MHz）
）
95

43 D201050030 76BTRF-E R D701 1
44 D201050020 50BTRF-E D702 1
45 D201050030 76BTRF-E R D703 1
46 D201050020 50BTRF-E D704 1
47 D201050030 76BTRF-E R D705 1
48 D201050020 50BTRF-E D706 1
49 D201050030 76BTRF-E R D707 1
50 D201050020 50BTRF-E D708 1
51 D201020020 BB1 D709 1
52 D101030030 S11100L D710 1
96

56 2001063350 Multilayer inductor 0603 3.3uH L701 1
60 2101082230 inductor 0805 22nH L705 1
63 2101061040 inductor 0603 100nH L708 1
65 2101082730 inductor 0805 27nH L710 1
66 2101061040 inductor 0603 100nH L711 1
69 T101020010 2SC5108-Y Q104 1
70 F101010010 K52-T1B-A Q701 1
71 F101010010 K52-T1B-A Q702 1
72 T101020010 2SC5108-Y Q703 1
73 T101020020 2SC4738GR Q704 1
74 T101020020 2SC4738GR Q705 1
75 T101040050 DTC114EE(TL) Q706 1
76 T101020020 2SC4738GR Q707 1
77 T101020010 2SC5108-Y Q708 1
97

104 1601991000 Trimmer capacitor 3.2*2.5*1.25mm TC701 1
98
QM-790-V （136-174MHz）
）
99

43 D201050030 76BTRF-E R D701 1
44 D201050020 50BTRF-E D702 1
45 D201050030 76BTRF-E R D703 1
46 D201050020 50BTRF-E D704 1
47 D201050030 76BTRF-E R D705 1
48 D201050020 50BTRF-E D706 1
49 D201050030 76BTRF-E R D707 1
50 D201050020 50BTRF-E D708 1
51 D201020020 BB1 D709 1
52 D101030030 S11100L D710 1
100
No. Material
Material No. Material Name Ref.No. Qty. Note
60 2101083930 inductor 0805 39nH L705 1
65 2101085630 inductor 0805 56nH L710 1
68 T101020010 2SC5108-Y Q104 1
69 F101010010 K52-T1B-A Q701 1
70 F101010010 K52-T1B-A Q702 1
71 T101020010 2SC5108-Y Q703 1
72 T101020020 2SC4738GR Q704 1
73 T101020020 2SC4738GR Q705 1
74 T101040050 DTC114EE(TL) Q706 1
75 T101020020 2SC4738GR Q707 1
76 T101020010 2SC5108-Y Q708 1
101

102
QM-790 Display Unit
No: Material No: Material Name Ref.No: Qty Note

7 1101041010 Chip resistor 0603 100Ω J 1/16W LED2309 1
27 1301040180 18S02015 Z1347 1
28 1301040180 18S02015 Z1348 1
29 1301040180 18S02015 Z1354 1
103
No: Material No: Material Name Ref.No: Qty Note

30 1301040180 18S02015 Z1319 1
34 1501041010 Chip capacitor 0402 100PF J 50V Z1301 1
35 1501041010 Chip capacitor 0402 100PF J 50V Z1355 1
38 2201040050 G21005U221TF L1301 1
39 T101040050 DTC114EE(TL) Q1303 1
40 T101040050 DTC114EE(TL) Q1304 1
41 T101040050 DTC114EE(TL) Q1301 1
42 T101040310 1132 Q1302 1
43 D501090020 1608SRC-PRV LED2300 1
44 D501090020 1608SRC-PRV LED2313 1
45 D501090010 1608SGC LED2302 1
46 D501090010 1608SGC LED2306 1
47 D501090010 1608SGC LED2307 1
48 D501090010 1608SGC LED2308 1
49 D501090010 1608SGC LED2312 1
50 D501090010 1608SGC LED2314 1
51 D501090010 1608SGC LED2315 1
52 3181200010 76DH IC2301 1
53 4411032010 FPV32VZAL-H-CN J1302 1
54 4479001000 RJ45 J2301 1
55 4005030010 RD901F K2301 1
104
QM790 Block Diagram
- 105 -
QM-790 Schematic Diagram
QM790 MCU Diagram
106
QM790 power supply schematic Diagram
107
QM-790 AF PA schematic Diagram
108
QM-790 Baseband schematic
109
QM-790 PLL Schematic
110
QM-790-U VCO Schematic
111
QM-790-U RF Schematic
112
QM790-V VCO Schematic
113
QM790-V RF Schematic
114
Specifications QM-790 Service Manual
Specifications
General
Frequency Range VHF: 136-174 MHz
UHF: 400-470 MHz 450-520 MHz
Channel Capacity 16CH/zone
Zone Capacity 8
Channel Spacing 25/20/12.5KHz
Operating Voltage 13.6V DC ±20%
Standby: 0.5A
Current
Receive: <2.0A
Drain
Transmit: <8A(25W)/<12A (45W)
Frequency Stability ±2.5ppm
Operating Temperature -30℃~+60℃
Antenna Impedance 50Ω
Dimensions (W×H×D) 152mm×44mm×143mm
Weight 1 Kg
Transmitter
RF Power Output 25W /45W
Modulation 16KΦF3E/11KΦF3E
Spurious and Harmonics 75dB
FM Noise(wide/medium/narrow) >45dB (25/20KHz)
>40dB (12.5KHz)
Audio Distortion ≤3%
Modulation limiting ±2.5@12.5KHz; ±4.0@20KHz; ±5.0@25KHz
Audio Response +1 to-3 dB
(from 6 dB/octave pre-emphasis

300-3000Hz)
- 115 -
Specification
Receiver
Sensitivity (12dB SINAD) EIA(μV) 0.28(12.5KHz) / 0.25(20/25KHz)
Selectivity(wide/medium/narrow) 70/65/60(25/20/12.5KHz)
Intermodulation(wide/medium/narrow) 75dB
Spurious Response Rejection 75dB
S/N(Signal-to-noise ratio) >45dB (25/20KHz)
>40dB (12.5KHz)
Internal Audio Power Output (Rated) 5W (less than 5% distortion)
External Audio Power Output (Rated) 10W (less than 5% distortion) /8ohm Load
Audio Response(300-3000Hz) +1 to-3 dB
116
© 2010 Quantun Electronics, LLC. All Rights Reserved

1379 Shotgrn Road, Sunrise, Florida 33326
V0.1A
P/N 7130790010
- 117 -

QM - 790 Service Manual V03

Uploaded by

Copyright:

Available Formats

QM - 790 Service Manual V03

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

QM - 790 Service Manual V03

Uploaded by

Copyright:

Available Formats

l

QM-790 Professional Mobile Radio

Installation Safety Guidelines

1. Display zone/channel number.

2. Display zone/channel label

3. Display channel frequency

5. Display DTMF digit

6. Display GPS coordinates

7. Display menu, setting items, etc.

1. Appears when the selected channel is busy

2. The bar number indicate the channel RSSI

Appears when the transmitting power is low

Appears when squelch open

Appears when call transmission is selected

1. C Indicating that the selected channel is contained in the

2. C● Indicating that the selected channel is programmed as

3. ●C Indicating that the selected channel is programmed as

4. flashed appears when the scan function is activated

Appears when compander function is enabled

Appears when scrambler function is enabled

Appears when GPS function is enabled

Appears when VOX function is enabled

Appears when the Aux port is activated

Programmable Auxiliary Functions

26. Lone work

Transmitting LED glows red

Receiving LED glows green when carrier

Scanning Green LED flashes once every 1

User Mode Conventional Mode

Panel Tuning Mode

Model Set Mode

Wired Clone Mode

Firmware Version Display Mode

2. Keypad Entry for Mode Startup

Center _C *** CTCSS: 67.0Hz

- Low No signalling, SQL off

High _H *** No signalling, SQL off

Center _C *** No signalling

SQL 3 Low _L *** No signalling

3. Model Set Mode

Model Rx/Tx 1(C) 2(L) 3(H) 4 5 6 7 8

Figure 1 Receiver Circuit

2.1 High Frequency Bandpass Amplifier Circuit

2.5 Squelch Open

Figure 2 Transmitter Circuit

3.1 MIC and Modulation Circuit

Figure 4 Control Circuit

5.2 Power Supply

Figure 5 Power Supply Circuit

Figure 6 Display Circuit

CPU PIN Function

59 P31/A9 MIC_mute O Mic mute Mute: H

Pin No. Name Description

J2301 (To MIC Jack)

J2302 (To Tx/Rx Unit)

J502 (To Display Unit)

J504 (to Speaker)

J2503 (to Repeater)

Ⅱ Panel Tuning Mode