Phase (Which May Be A Gas, A Liquid or A Supercritical Fluid) - The Mobile Phase Is

Chromatography
Introduction
Few methods of chemical analysis are truly specific to a particular analyte. It is

often found that the analyte of interest must be separated from the myriad of
individual compounds that may be present in a sample. As well as providing the
analytical scientist with methods of separation, chromatographic techniques can
also provide methods of analysis.
Chromatography involves a sample (or sample extract) being dissolved in a mobile

phase (which may be a gas, a liquid or a supercritical fluid). The mobile phase is
then forced through an immobile, immiscible stationary phase. The phases are
chosen such that components of the sample have differing solubilities in each
phase. A component which is quite soluble in the stationary phase will take longer
to travel through it than a component which is not very soluble in the stationary
phase but very soluble in the mobile phase. As a result of these differences in
mobilities, sample components will become separated from each other as they
travel through the stationary phase.
Techniques such as H.P.L.C. (High Performance Liquid Chromatography) and G.C.

(Gas Chromatography) use columns - narrow tubes packed with stationary phase,
through which the mobile phase is forced. The sample is transported through the
column by continuous addition of mobile phase. This process is called elution. The
average rate at which an analyte moves through the column is determined by the
time it spends in the mobile phase.
Distribution of analytes between phases
The distribution of analytes between phases can often be described quite simply. An
analyte is in equilibrium between the two phases;
Amobile Astationary
The equilibrium constant, K, is termed the partition coefficient; defined as the molar
concentration of analyte in the stationary phase divided by the molar concentration
of the analyte in the mobile phase.
The time between sample injection and an analyte peak reaching a detector at the
end of the column is termed the retention time (tR ). Each analyte in a sample will
have a different retention time. The time taken for the mobile phase to pass
through the column is called tM.
A term called the retention factor, k', is often used to describe the migration rate of
an analyte on a column. You may also find it called the capacity factor. The
retention factor for analyte A is defined as;
k'A = t R - tM / tM
t R and tM are easily obtained from a chromatogram. When an analytes retention

factor is less than one, elution is so fast that accurate determination of the retention
time is very difficult. High retention factors (greater than 20) mean that elution
takes a very long time. Ideally, the retention factor for an analyte is between one
and five.
We define a quantity called the selectivity factor, a , which describes the separation
of two species (A and B) on the column;
a = k 'B / k 'A
When calculating the selectivity factor, species A elutes faster than species B.
The selectivity factor is always greater than one.
Band broadening and column efficiency
To obtain optimal separations, sharp, symmetrical chromatographic peaks must be

obtained. This means that band broadening must be limited. It is also beneficial to
measure the efficiency of the column.
The Theoretical Plate Model of Chromatography
The plate model supposes that the chromatographic column is contains a large
number of separate layers, called theoretical plates. Separate equilibrations of the
sample between the stationary and mobile phase occur in these "plates". The
analyte moves down the column by transfer of equilibrated mobile phase from one
plate to the next.
It is important to remember that the plates do not really exist; they are a
figment of the imagination that helps us understand the processes at work in the
column.They also serve as a way of measuring column efficiency, either by stating
the number of theoretical plates in a column, N (the more plates the better), or by
stating the plate height; the Height Equivalent to a Theoretical Plate (the smaller
the better).
If the length of the column is L, then the HETP is
HETP = L / N
The number of theoretical plates that a real column possesses can be found by
examining a chromatographic peak after elution;
where w1/2 is the peak width at half-height.
As can be seen from this equation, columns behave as if they have different
numbers of plates for different solutes in a mixture.
The Rate Theory of Chromatography
A more realistic description of the processes at work inside a column takes account
of the time taken for the solute to equilibrate between the stationary and mobile
phase (unlike the plate model, which assumes that equilibration is infinitely fast).
The resulting band shape of a chromatographic peak is therefore affected by the
rate of elution. It is also affected by the different paths available to solute molecules
as they travel between particles of stationary phase. If we consider the various
mechanisms which contribute to band broadening, we arrive at the Van Deemter
equation for plate height;
HETP = A + B / u + C u
where u is the average velocity of the mobile phase. A, B, and C are factors which
contribute to band broadening.
A - Eddy diffusion
The mobile phase moves through the column which is packed with stationary phase.
Solute molecules will take different paths through the stationary phase at random.
This will cause broadening of the solute band, because different paths are of
different lengths.
B - Longitudinal diffusion
The concentration of analyte is less at the edges of the band than at the center.
Analyte diffuses out from the center to the edges. This causes band broadening. If
the velocity of the mobile phase is high then the analyte spends less time on the
column, which decreases the effects of longitudinal diffusion.
C - Resistance to mass transfer

The analyte takes a certain amount of time to equilibrate between the stationary
and mobile phase. If the velocity of the mobile phase is high, and the analyte has a
strong affinity for the stationary phase, then the analyte in the mobile phase will
move ahead of the analyte in the stationary phase. The band of analyte is
broadened. The higher the velocity of mobile phase, the worse the broadening
becomes.
Van Deemter plots

A plot of plate height vs. average linear velocity of mobile phase.
Such plots are of considerable use in determining the optimum mobile phase flow
rate.
Resolution
Although the selectivity factor, a, describes the separation of band centres, it does
not take into account peak widths. Another measure of how well species have been
separated is provided by measurement of the resolution. The resolution of two
species, A and B, is defined as
Baseline resolution is achieved when R = 1.5
It is useful to relate the resolution to the number of plates in the column, the
selectivity factor and the retention factors of the two solutes;
To obtain high resolution, the three terms must be maximised. An increase in N, the
number of theoretical plates, by lengthening the column leads to an increase in
retention time and increased band broadening - which may not be desirable.
Instead, to increase the number of plates, the height equivalent to a theoretical
plate can be reduced by reducing the size of the stationary phase particles.
It is often found that by controlling the capacity factor, k', separations can be
greatly improved. This can be achieved by changing the temperature (in Gas
Chromatography) or the composition of the mobile phase (in Liquid
Chromatography).
The selectivity factor, a, can also be manipulated to improve separations. When a is

close to unity, optimising k' and increasing N is not sufficient to give good
separation in a reasonable time. In these cases, k' is optimised first, and then a is
increased by one of the following procedures:
1. Changing mobile phase composition
2. Changing column temperature
3. Changing composition of stationary phase
4. Using special chemical effects (such as incorporating a species which

complexes with one of the solutes into the stationary phase)

Phase (Which May Be A Gas, A Liquid or A Supercritical Fluid) - The Mobile Phase Is

Uploaded by

Copyright:

Available Formats

Phase (Which May Be A Gas, A Liquid or A Supercritical Fluid) - The Mobile Phase Is

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Phase (Which May Be A Gas, A Liquid or A Supercritical Fluid) - The Mobile Phase Is

Uploaded by

Copyright:

Available Formats

Chromatography

Few methods of chemical analysis are truly specific to a particular analyte. It is

Chromatography involves a sample (or sample extract) being dissolved in a mobile

Techniques such as H.P.L.C. (High Performance Liquid Chromatography) and G.C.

Distribution of analytes between phases

t R and tM are easily obtained from a chromatogram. When an analytes retention

Band broadening and column efficiency

To obtain optimal separations, sharp, symmetrical chromatographic peaks must be

The Theoretical Plate Model of Chromatography

If the length of the column is L, then the HETP is

where w1/2 is the peak width at half-height.

The Rate Theory of Chromatography

C - Resistance to mass transfer

Van Deemter plots

The selectivity factor, a, can also be manipulated to improve separations. When a is

1. Changing mobile phase composition

2. Changing column temperature

3. Changing composition of stationary phase

4. Using special chemical effects (such as incorporating a species which

You might also like