Link OS v6.4ReleaseNotes

Link-OS
Release Notes
P1105470-11EN
ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corporation, registered in
many jurisdictions worldwide. All other trademarks are the property of their respective owners.
© 2021 Zebra Technologies Corporation and/or its affiliates. All rights reserved.
Information in this document is subject to change without notice. The software described in this document
is furnished under a license agreement or nondisclosure agreement. The software may be used or copied
only in accordance with the terms of those agreements.
For further information regarding legal and proprietary statements, please go to:
SOFTWARE: zebra.com/informationpolicy
COPYRIGHTS: zebra.com/copyright
WARRANTY: zebra.com/warranty
END USER LICENSE AGREEMENT: zebra.com/eula
Terms of Use
Proprietary Statement
This manual contains proprietary information of Zebra Technologies Corporation and its subsidiaries
(“Zebra Technologies”). It is intended solely for the information and use of parties operating and
maintaining the equipment described herein. Such proprietary information may not be used, reproduced,
or disclosed to any other parties for any other purpose without the express, written permission of Zebra
Technologies.
Product Improvements
Continuous improvement of products is a policy of Zebra Technologies. All specifications and designs are
subject to change without notice.
Liability Disclaimer
Zebra Technologies takes steps to ensure that its published Engineering specifications and manuals are
correct; however, errors do occur. Zebra Technologies reserves the right to correct any such errors and
disclaims liability resulting therefrom.
Limitation of Liability
In no event shall Zebra Technologies or anyone else involved in the creation, production, or delivery of the
accompanying product (including hardware and software) be liable for any damages whatsoever
(including, without limitation, consequential damages including loss of business profits, business
interruption, or loss of business information) arising out of the use of, the results of use of, or inability to
use such product, even if Zebra Technologies has been advised of the possibility of such damages. Some
jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
Publication Date
September 2, 2021
2
Version Numbers and
Printer Models
This document applies to all Link-OS printer models. Exceptions are noted as needed.
Newer releases by Link-OS version

Link-OS v6.4 Release Notes .................................................................................................................................6
Link-OS v6.3 Release Notes ...............................................................................................................................11
Link-OS v5.x Release Notes ...............................................................................................................................30
Older releases by firmware version

V68 Printer OS Release Notes............................................................................................................................33
V74 Printer OS Release Notes..........................................................................................................................103
For the printer models supported by the different firmware versions, see Table 1 on page 4.
For support, please visit zebra.com/support.
3
Version Numbers and Printer Models
Table 1 Printer Firmware Versions

Printer Models OS Branch
QLn220 V68
QLn320
QLn420
QLn220 HC
QLn320 HC
ZT210 V72
ZT220
ZT230
iMZ220 V73
iMZ320
ZD500 V74
ZD500R
ZT410 V75
ZT420
ZQ510 V76
ZQ520
ZR338 V78
ZR628 V79
ZR638
ZT510 V80
ZT610
ZT620
ZQ310 V81
ZQ320
ZR318 V82
ZR328
ZD510 V83
ZD410D V84
ZD420C
ZD420D
ZD420T
ZD620D
ZD620T
ZQ610 V85
ZQ620
ZQ630
ZR658 V86
ZR668
ZD220 V89
ZD230
ZD888
ZT411 V92
ZT421
4
Version Numbers and Printer Models
Table 1 Printer Firmware Versions (Continued)

Printer Models OS Branch
ZD421C V93
ZD421D
ZD421T
ZD621D
ZD621T
ZE511 V94
ZE521
5
Link-OS v6.4 Release Notes
This document applies to all listed Link-OS printer models. Exceptions are noted as needed.
Link-OS 6.4
Release Date: 3 September 2021
Applies to the following Link-OS printer models:
Printer Models OS Branch Build Printer Models OS Branch Build

ZT210 V72. 20.23Z ZQ610 V85. 20.23Z
ZT220 ZQ620
ZT230 ZQ630
ZD500 V74. 20.23Z ZR658 V86. 20.23Z
ZR668
ZT510 V80. 20.23Z ZD220 V89. 21.09Z
ZT610 ZD230
ZT620 ZD888
ZQ310 V81. 20.23Z ZQ511 V91. 21.09Z
ZQ320 ZQ521
ZR318 V82. 20.23Z ZT411 V92. 21.09Z
ZR328 ZT421
ZD510 V83. 20.23Z ZD421C V93. 21.09Z
ZD421D
ZD421T
ZD621D
ZD621T
ZD410D V84. 20.23Z ZE511 V94. 21.09Z
ZD420C ZE521
ZD420D
ZD420T
ZD620D
ZD620T
6
Changes
1. The Link-OS version number is now v6.4.
2. The Monarch®, Sato©, and ESC-POS© 200 dpi emulations will now be preloaded into the printer as
new printers are manufactured, with the exception of the ZT2x0 and ZR3x8 due to memory constraints.
The emulations will also continue to be available on zebra.com for download and use (only on printers
that have been updated to Link-OS v6.4).
3. The term “Virtual Device” has been replaced with the term “Emulation.”
4. Command Language can now be changed from the Color Touch Front Panel. It is located under
Program Language in the System menu.
5. Backfeed can now be changed from the Color Touch Front. It is located under Image Adjust in the
Print menu.
6. The Sato emulation now supports graphic rotation using the <ESC>% command.
7. The SGDs weblink.ip.conn1 and weblink.ip.conn2 can no longer be set to the same location.
8. The RFID Void pattern has been improved for readability.
9. The Batch Counter display on the Color Touch Front Panel has been improved to add the total number
of labels being printed.
10. A new print.xi_compatibility_adjust Set-Get-Do command has been added to the ZT5xx and
ZT6xx printer models, which will enable the user to proportionately decrease the length of a printed
label. The range of values is from 96.0 to 100.0 with a default value of 100.0. The setting will not be
changed by defaulting the printer. An example usage would be:
! U1 setvar "print.xi_compatibility_adjust" "98.6"
Frequently Asked Questions:

1. “Why should I upgrade to v6.4?”
Zebra continually revises and adapts our printer operating system to keep it current with the latest
technology trends and best practices. Version 6.4 contains both improvements, such as new Supplies
Use Visibility features, but also fixes that could otherwise positively impact your business. We
encourage updating to the latest version to take advantage of the new features and fixes.
2. “How do I get Link-OS v6.4?”
Link-OS v6.4 can be downloaded from the Zebra web site by using the link below and entering your
printer’s model name (such as “ZT411” or “ZQ620”).
zebra.com/support
You can then use one of our utilities, such as the Z-Downloader, to update your printer. For details on
using Z-Downloader, go to:
zebra.com/us/en/support-downloads/knowledge-articles/using-the-z-downloader-utility-available-from-t
he-zebra-website.html
3. “What does Link-OS v6.4 cost?”
Link-OS v6.4 is a free upgrade.
7
4. “As of Link-OS v5.1, Industrial and Desktop printers can’t be downgraded to versions earlier than v.5.1.
Why is that?”
To maintain continuity in Zebra’s manufacturing process and to address global constraints on flash
memory availability, a new set of memory components may be used as new printers are manufactured.
These new memory components are future compatible with Link-OS v5.1 and later printer Operating
System releases but will not be back-compatible with earlier Link-OS versions.
To ensure compatibility between the flash memory and printers operating systems, Industrial and
Desktop printers that are already running v5.1 or later will not support downgrading to printer’s OS
versions earlier than v5.1.
When and if an attempt is made to downgrade from v5.1 to and earlier build, the older build will not be
loaded. The printer will not accept the older operating system and will return to using the v5.1 or later
version currently loaded on the printer. The printer will provide feedback that the download is not
supported, using one of the following methods:
• On printers with a screen, the message “Download Not Supported” will be displayed. In addition, the
LED's on the printer will behave in the following way – the status LED will turn solid red. The other 4
LEDs will be cycled on 1 at a time, changing the "on" LED every second. The exception to this is the
ZD500 series printer. On that unit the Status LED will turn red.
• On printers with no screen, the status LED will turn solid red. The other 4 LEDs will be cycled on 1 at
a time, changing the "on" LED every second.
Issues Corrected
1. Holding the Feed button for 7 seconds or more now correctly places the Bluetooth radio in discovery
mode.
2. Turning off WLAN no longer disables the Bluetooth radio.
3. The "power.energy_star.enable", "power.energy_star.timeout" and "power.energy_star.active" SGDs
now function correctly on ZD4x0/ZD6x0 printers.
4. When using EPL stored forms, all of the previous label image will now be cleared properly.
5. Setting the IP protocol to Permanent on the printer's web page no longer resets the gateway to all
zeros.
6. In some circumstance when using RFID TID serialization, duplicate serial numbers could be created.
This has been corrected.
7. The EPL Black Mark command (part of the Q command) now correctly changes the value of the SGD
media.tof.
8. Mirror now correctly authenticates with AIX SFTP servers when using keyboard interactive mode.
9. The ribbon cartridge on a ZD420c now correctly authenticates when using WLAN EAP-TLS security.
10. An interaction between LPR printing and ZBI that was causing some labels to not be printed has been
corrected.
11. The value returned by the EPL êe command when printing in peel mode has been corrected to be
backward compatible.
12. Setting the SGD "device.sensor_profile" to the value "reply" now works correctly.
13. Tear off on 600 dpi ZT600 printers has been corrected to be backward compatible.
14. The ZBI system has been optimized to ensure that data is received properly.
15. The printer web page format preview feature has been enhanced to handle large formats.
8
16. Any ZBI program can now be selected for execution from the Color Touch Front Panel when more than
one is present.
17. When printing on a ZT6x0 printer in rewind mode, only one label will now be fed per press of the Feed
button.
18. Media Out condition on ZD4x0/ZD6x0 printers has been corrected to be backward compatible.
19. The calibrated media type is now correctly saved when using the two key (PAUSE + CANCEL)
calibration method.
20. The SGD "ip.dhcp.vendor_class_id" now correctly saves its value when set.
21. On ZQ5x1 printers, when connected via USB, the printer Emulation setting is now properly maintained
across a power cycle.
22. The SNMP table zebra.zbrSupplies.zbrSuppliesRibbonCartTable now correctly saves its values.
23. WLAN now correctly handles the situation when the connection is closed due to wlan.timeout.value
expiring and only a partial format has been received.
24. The printer now correctly manages very short connection/disconnect events when large numbers of
TCP/IP port 9100 connection attempts are made.
25. The battery charging process on ZQ5x1 and ZQ6x0 printers has been optimized.
26. Large numbers of repeated requests on certain SNMP OIDS now function correctly.
27. A WPA PSK passkey entered as a string on the Color Touch Front Panel is now correctly converted to
a PSK key per RFC2898.
28. WLAN process synchronization has been improved to prevent a situation where DHCP requests could
be ignored.
29. Serial Communication settings that are set with ^SC are now properly saved when a ^JUS is used.
30. Serial Communication settings set with the printer web pages are now correctly saved.
31. On 600 dpi printers, print images with data on the very first dot row no longer create extra wear on the
print head.
32. The ZQ6x0 series quad bay sustains battery temperature during charging.
33. USB Host is now compatible with additional USB scanners and keyboards.
9
Upcoming Changes
Zebra is announcing:
• SHA-1 support will be removed in the future “Version 7” of the Link-OS Printer OS. This step is being
taken to enhance product security. SHA-1 is still supported in Link-OS v6.0. It will be removed in
Link-OS v7.0 and beyond.
• The rfid.adaptive_antenna command will be removed in the future “Version 7” of the Link-OS Printer
OS.
• A new means of defining an internet firewall proxy that would apply to all Ethernet and WLAN
connections will be added in a future version of Link-OS. The settings used will be ip.firewall.proxy,
ip.firewall.authentication.add, ip.firewall.authentication.entries, and
ip.firewall.authentication.remove.
10
Link-OS 6.3
Release Date: 31 August 2020

ZT210 V72. 20.22Z ZD410D V84. 20.22Z
ZT220 ZD420C
ZT230 ZD420D
ZD420T
ZD620D
ZD620T
ZD500 V74. 20.22Z ZQ610 V85. 20.22Z
ZQ620
ZQ630
ZQ510 V76. 20.22Z ZR658 V86. 20.22Z
ZQ520 ZR668
ZT510 V80. 20.22Z ZD220 V89. 21.05Z
ZT610 ZD230
ZT620 ZD888
ZQ310 V81. 20.22Z ZQ511 V91. 21.05Z
ZQ320 ZQ521
ZR318 V82. 20.22Z ZT411 V92. 21.05Z
ZR328 ZT421
ZD510 V83. 20.22Z
11
Changes
1. The Link-OS version number is now v6.3.
2. The PDF Direct emulation, which was previously a paid option, will be no charge as of this release. The
emulation will be preloaded into the printer as new printers are manufactured. The emulation will also
be available on zebra.com for download and use (only on printers that have been updated to Link-OS
v6.3).
3. Link-OS v6.3 uses an improved method to control low-battery behavior. This method delivers more
consistent image quality when printing large amounts of black and when printing in low temperatures.
This method also has the benefit of improving battery charging reliability and avoiding premature printer
shutdown. We recommend users experiencing an inability to charge their battery or earlier than
expected printer shutdown events, update their printers to Link-OS v6.3.
4. A new "device.reset_button_enable" Set-Get-Do command has been added to the ZD4, ZD6 and
ZD888 printer models, which will enable the user to disable the physical reset button. The default for
the command will be "on", users can choose to set it to "off". The setting will not be changed by
defaulting the printer.
5. The SGD command "internal_wired.8021x.security" is now included in the list of commands covered by
Protected Mode.
6. The RFID encoding system in the ZT610R is certified for use in Cambodia, Myanmar, Pakistan, &
Ethiopia
7. The SNMP system will now log Alert Clear events. The MIB file has been updated and will be posted
along with this new release.

zebra.com/support
12
Why is that?”
• On printers with no screen, the status LED will turn solid red. The other 4 LEDs will be cycled on 1 at
a time, changing the "on" LED every second.
Issues Corrected
1. Charging management for extended battery pack used on the ZQ511, ZQ521, and ZQ600 series
printers has been updated to extend battery health over time.
2. Support for Fast BSS Transition (802.11r) has been improved.
3. The Wi-Fi system has been enhanced to ensure DHCP generated addresses are maintained over link
loss events.
4. The ZQ600 series has been enhanced to better support Wi-Fi roaming events.
5. The TCP connection system has been enhanced to properly handle, in all cases, connection requests
when the number of open connections is at the maximum limit.
6. An issue where the CPCL Font 7 printed an empty space after a 0xD6 character has been corrected.
7. It is now possible to encode a serial number in a DataMatrix barcode when the serial number ends
in “00”'.
8. GS1 Application Identifier encoding in DataMatrix barcodes has been corrected.
9. The ZBI system has been enhanced to ensure that Bluetooth will reconnect after the Bluetooth
connection is closed and a reconnection request occurs.
10. JSON responses for battery status information have been corrected so that software applications can
correctly retrieve information.
11. The Sleep system on the ZD620 has been enhanced to protect against print job loss when the printer is
entering sleep mode.
12. The Bluetooth Mode name has been changed to “Client”.
13
Upcoming Changes
OS.
14
Link-OS 6.2
Release Date: 03 March 2020

ZD500 V74 20.21Z ZD410D V84 20.21Z
ZD500R ZD420C
ZT410 V75 20.21Z ZD420D
ZT420 ZD420T
ZD620D
ZD620T
ZQ510 V76 20.21Z ZQ610 V85 20.21Z
ZQ520 ZQ620
ZQ630
ZT510 V80 20.21Z ZR658 V86 20.21Z
ZT610 ZR668
ZT620
ZQ310 V81 20.21Z ZD220 V89 21.04Z
ZQ320 ZD230
ZD888
ZR318 V82 20.21Z ZT411 V92 21.04Z
ZR328 ZT421
ZD510 V83 20.21Z
15
Changes
Sleep Mode has been disabled in the following models: ZD410D, ZD420C, ZD420D, ZD420T,
ZD620D,ZD620T in order to prevent the printer from continuing to process a print job after it has begun
entering sleep mode. Sleep mode will be reenabled in a future Printer OS release.

zebra.com/support
Why is that?”
• On printers with no screen, the status LED will turn solid red. The other 4 LEDs will be cycled on 1
at a time, changing the "on" LED every second.
16
Issues Corrected
1. JSON handling has been improved so that repeated requests to the printer via BTLE do not hold up
communications.
2. Sending larger files (larger than 20 MB) over the Bluetooth Classic connection has been optimized to
ensure all data is sent.
3. Bluetooth Low Energy communication with iOS devices improved to more reliably handle reconnect
events
4. Bluetooth version number is now being reported correctly
Upcoming Changes
OS.
17
Link-OS 6.1
Release Date: 8 November 2019

ZT210 V72 20.20Z ZD410D V84 20.20Z
ZT220 ZD420C
ZT230 ZD420D
ZD500 V74 20.20Z ZD420T
ZD500R ZD620D
ZT410 V75 20.20Z ZD620T
ZT420
ZQ510 V76 20.20Z ZQ610 V85 20.20Z
ZQ520 ZQ620
ZQ630
ZT510 V80 20.20Z ZR658 V86 20.20Z
ZT610 ZR668
ZT620
ZQ310 V81 20.20Z ZD220 V89 21.03Z
ZQ320 ZD230
ZD888
ZR318 V82 20.20Z ZT411 V92 21.03Z
ZR328 ZT421
ZD510 V83 20.20Z
18
Changes:
Summary:
• Improved ease of use for the Tap/Pair and Scan/Pair apps when using Bluetooth Security Mode 1.
• Selected Simple Network Management Protocol (SNMP) responses have been updated.
• New Supplies Use Visibility features have been added.
Details:
Improved ease of use for the Tap/Pair and Scan/Pair apps when using Bluetooth Security Mode 1
When “bluetooth.minimum_security_mode” is set to “1”, the printer will unconditionally enable Bluetooth
pairing. This allows easier use of the Tap/Pair and Scan/Pair apps when the printer is configured for
Bluetooth Security Mode 1.
Selected Simple Network Management Protocol (SNMP) responses have been updated.
• .1.3.6.1.2.1.1.1.0 – sysDescr – the response has changed to this structure:
“company name product name active print server”
Example: “Zebra Technologies ZD510-300dpi / internal wired”
Previous response: name of the active print server
• . 1.3.6.1.2.1.1.5.0 – sysName – the response has changed to this structure:
“Product name”
Example: “ZD510”
Previous response: Product Serial Number
• .1.3.6.1.2.1.25.3.2.1.3 – hrDeviceDescr – the response has changed to this structure:
“Product name model name’
Example: “Zebra Technologies ZD510
Previous response: “Zebra Printer”
New Supplies Use Visibility features have been added.

• A new “zbrOdometerNetRibbonUse” OID has been added: .1.3.6.1.4.1.10642.3.1.18.
This tracks the total net length of ribbon that has moved through the printer, with backup movement
compensated for.
• A new “odometer.net_ribbon_length” SGD command has been added.
This tracks the total net length of ribbon that has moved through the printer, with backup movement
compensated for.
• A new “zbrOdometerNetMediaUse” OID has been added: .1.3.6.1.4.1.10642.3.1.19.
This tracks the total net length of media that has moved through the printer, with backup movement
compensated for.
• A new “odometer.net_media_length” SGD command has been added.
This tracks the total net length of media that has moved through the printer, with backup movement
compensated for.
19
• A new “zbrSuppliesMediaCartTable” SNMP table has been added: .1.3.6.1.4.1.10642.48.1.3

This tracks data on the last 100 media cartridges that have been used in the printer. Data in the table
includes:
• An index value
• The number of times the cartridge has been installed
• If a media cartridge is installed or not
• The part number for the cartridge
• The serial number for the cartridge
• The total length of the media in the cartridge
• The width of the media in the cartridge
• The print speed used with the cartridge
• The darkness level used with the cartridge
• The total number of labels in a new cartridge
• The total number of labels remaining in the cartridge
• A new “zbrSuppliesRibbonCartTable” SNMP table has been added: .1.3.6.1.4.1.10642.48.2.3
This tracks data on the last 100 ribbon cartridges that have been used in the printer. Data in the table
includes:
• An index value
• The number of times the cartridge has been installed
• The part number for the cartridge
• The serial number for the cartridge
• The type of ribbon in the cartridge
• The total length of the ribbon in the cartridge
• The width of the ribbon in the cartridge
• The total length of ribbon in a new cartridge
• The total number of labels remaining in the cartridge
• A new “zbrSuppliesMediaRollTable” SNMP table has been added at .1.3.6.1.4.1.10642.48.1.4
This tracks data on the last 100 media calibration length events that occurred on the printer. Data in the
table includes:
• An index value
• If a media roll is installed or not (future use)
• The part number for the media (future use)
• The serial number for the media (future use)
• The calibrated length of the currently loaded media
• The width of the media (future use)
• The print speed used with the media (future use)
• The darkness level used with the media (future use
• The toal number of labels on a new roll (future use)
20
• The number of labels remaining on the roll (future use)

• A new “zbrTrackedAlertsTable” SNMP table has been added at .1.3.6.1.4.1.10642.10.31
This tracks data on a specific set of the last 50 alert events. Data in the table includes:
• An index value
• The Alert Severity
• The Alert “Training Level”, which identifies the training level needed to address the alert
• The Alert Group, which identifies the printer subsystem the Alert happens within.
• The value of the sysUpTime (.1.3.6.1.2.1.1.3.0) when the Alert occurred
• The Alert Code, which can include:
• ribbon-out
• head-too-hot
• head-under-temp
• head-open
• power-supply-over-temp
• motor-over-temp
• ribbon-in
• rewind-fault
• cutter-jammed
• printer-paused
• head-element-bad
• basic-runtime
• basic-forced
• power-on
• battery-low
• rfid-error
• cold-start
• ribbon-auth-error
• NOTE: The zbrTrackedAlertsTable, zbrSuppliesMediaRollTable, zbrSuppliesMediaCartTable,
zbrSuppliesRibbonCartTable contents will be deleted when the printer Decommissioning feature
is used.
• NOTE: The Zebra SNMP Management Information Base (MIB) file contains more details. It can
be downloaded from zebra.com at zebra.com/us/en/support-downloads.html
Other Changes:
• The Link-OS version has been updated to v6.1
• The V68, V73, V78 and V79 builds are deprecated, they are no longer being updated.
21

printer’s model name (such as “ZT230” or “QLn320”).
zebra.com/support
Why is that?”
• On printers with no screen, the status LED will turn solid red. The other 4 LEDs will be cycled on 1
at a time, changing the "on" LED every second.
22
Issues Corrected:
• An issue with re-establishing a Bluetooth connection to an iOS device after the printer has been power
cycled has been corrected.
• A printer in sleep mode and connected to a Windows or OSX system via USB will now correctly “wake
up” when the Windows or OSX system wakes up.
• An Aztec code with no data will now not print and not otherwise impact printer responses.
• The German translation for "Label Length Cal" has been translated to “Etikettenlängenkal”.
Security Related Items:

• CVE-2019-9506 – also known as the Bluetooth Encryption Key Size Validation issue has been
addressed. Seethe following link for more details:
zebra.com/us/en/support-downloads/lifeguard-security/lifeguard-security-alerts.html
Upcoming Changes:
OS.
23
Link-OS 6.0
Release Date: 28 June 2019

ZT210 V72 .18 ZD410D V84 .18
ZT220 ZD420C
ZT230 ZD420D
ZD500 V74 .18 ZD420T .18
ZD500R ZD620D
ZT410 V75 .18 ZD620T .18
ZT420
ZQ510 V76 .18 ZQ610 V85 .19
ZQ520 ZQ620
ZQ630
ZT510 V80 .18 ZR658 V86 .18
ZT610 ZR668
ZT620
ZQ310 V81 .18 ZD220 V89 .01
ZQ320 ZD230
ZD888
ZR318 V82 .18 ZT411 V92 .18
ZR328 ZT421
ZD510 V83 .18 .18
24
Changes:
The OS now supports several new PrintSecure v2 features. See the Printer Administration Guide for
additional details on using these new features:
• Bluetooth Discovery and Pairing Mode: The bluetooth.discoverable function is now off by default.
• Bluetooth Discovery and Pairing Mode can be activated by holding the FEED button on the printer
for 5 seconds.
• Specifically, on the ZD220, ZD230, and ZD888 models, the 4 flash LED sequence places the printer
into Bluetooth Pairing Mode.
• Specifically, on the ZD510 model, the 5 flash LED sequence places the printer into Bluetooth Pairing
Mode.
Upon entering Bluetooth Pairing Mode, the printer will provide feedback that the printer is in Pairing
Mode using one of these methods:
• On printers with a “Bluetooth” screen icon or Bluetooth LED, the printer shall flash the “Bluetooth”
screen icon or Bluetooth LED on and off every second while in pairing mode
• On printers without a “Bluetooth” screen icon or Bluetooth LED, the printer shall flash the “Data” icon
or Data LED on and off every second while in pairing mode
NOTE: In any Bluetooth Security Mode, pairing will require placing the printer into the Discovery and
Pairing Modes by pressing and holding the FEED key, as described above. This applies in all use
cases and scenarios. (Added 8 November 2019.)
NOTE: Users can disable the ability to enable Bluetooth discovery and Pairing Mode by setting
bluetooth.enable to “off”. This will turn off the ability to Discover and Pair with the printer.
! U1 setvar "bluetooth.enable" "off"
• WLAN ESSID: The default ESSID "125" setting has been removed. The new default is an empty string.
The Zebra Printer Setup Utility, available for Windows, Android or iOS can be used to set the
command. See the Printer Administration Guide for details.
NOTE: The "wlan.essid" command can also be used to configure the command :
! U1 setvar "wlan.essid" "Your ESSID"
• Automated WLAN certificate Management: This feature, when used with the Printer Profile Manager
Enterprise server software, will automate WLAN certificate updating, keeping track of certificate
expiration dates, generating new certificate signing requests, getting them signed by the users
Certificate Authority and placing them on the printer prior to the existing certificate expiring. See the
Printer Administration Guide for details.
• Protected Mode: This feature allows the user to place the printer into a mode where a specific set of
settings cannot be changed unless a user defined password is sent to the printer. We recommend
consulting the Printer Administration Guide for details on using this feature.
• OS Download Blocking: This feature allows the user to place the printer in a mode where the printer’s
OS cannot be changed. We recommend consulting the Printer Administration Guide for details on using
this feature.
25
• Decommissioning Mode: This feature allows the user to return the printer to a factory-built state,
removing user files from the printer’s memory and defaulting all settings. Optionally, the user can
choose to have the printer write over its Flash memory up to three times. We recommend consulting the
Printer Administration Guide for details on using this feature.
NOTE: This command is not the same as defaulting the printer. Using it will remove files from the
printer’s memory, including fonts, graphics and certificates.
Other Changes:
• The Link-OS version has been updated to v6.0
• The OpenSSL library has been updated to version 1.0.2
• Support for the ZQ630 has been added
• Support for the ZD220, ZD230, and ZD888 has been added
• Support for the ZT411 and ZT420 has been added
• The ~HS, ^HZ and device.host_status commands will no longer report the printers pin code as set
by the ^KP command. Instead the command will always return 0000
• Bluetooth Low Energy support on the Bluetooth only ZQ510/ZQ520 and ZT600 printers has been
removed.
• All support for the WEP 40 bit and WEP 128 bit WLAN securities has been removed.
• The telnet menu and support for port 23 have been removed.
• The Remote-Auto-Connect feature has been removed.
• The OS now supports the Color Touch Display option on the ZT600 printer
• Several other new SGD commands have been created, see the Programming Guide for details.
• The default for the command "rfid.antenna_sweep" has been changed to "off"
• Thermal Transfer Mode only mode on the ZD420C has been added.
• Installing a 600 dpi printhead into a ZT500 or ZT600 that was manufactured as 200 dpi or 300 dpi
unit is no longer supported.
• The V68, V73, V78 and V79 builds are deprecated, they are no longer being updated.
• Some Printer OS releases are being announced prior to the release of the printer, since those new
printers will release initially running Link-OS v6.
26

technology trends and best practices. Version 6.0 contains both improvements, such as new
PrintSecure features, but also fixes that could otherwise positively impact your business. We
zebra.com/support
Why is that?”
LED's on the printer will behave in the following way – the status LED will turn solid red. The other
four LEDs will be cycled on one at a time, changing the "on" LED every second. The exception to
this is the ZD500 series printer. On that unit the Status LED will turn red.
• On printers with no screen, the status LED will turn solid red. The other four LEDs will be cycled on
one at a time, changing the "on" LED every second.
27
Issues Corrected:
1. The ZQ500 battery eliminator feature has been enhanced to better handle printing thick lines on the
label.
2. Issue fixed wherein LPD port 515 would stop responding.
3. The EMAIL (EML) port in ZBI programs will now function correctly.
4. RFID encoding issue with getting voids when reading certain data from the RFID tag. This included
using a number 2 and 9 at end of an encoded string
5. RFID labels will now be voided when a incorrectly formatted ^RU command is used.
6. The EPL AutoFR feature has been enhanced to better handle variable data that could appear as if it
was an EPL command
7. Support for nested “ifs” in WML has been corrected
8. Lower case characters are now allowed in the Change Caret command (^CC)
9. The EPL Q command setting and Black Mark offset setting will now be properly retained during power
up if the printer was in Mark mode when it powered down.
10. Media sensor calibration values on Mobile printers will be properly saved across a default and power
cycle
11. The Japanese translation for the word About on the ZT410 has been corrected.
12. The SNMP Pause Alert will no longer be sent twice when the Pause button is pressed
13. Storing the printer’s configuration report to the E drive has been corrected so that the file that is created
contains the correct content.
14. File names on the USB drive are now restricted to use only ASCII characters, not including these
characters * , / ? \ space (del)
15. SFTP support for Mirror now does not attempt to use "keyboard-interactive" authentication mode when
connecting to the FTP server
16. The networking system now supports an infinite DHCP address lease
17. Issue where the printer would not reconnect via Bluetooth with a host system after a disconnect event
has been corrected
18. Sleep mode on the ZQ600 has been improved to avoid the printer not properly entering sleep mode
when the buttons on the front panel are repeatedly pressed
19. An issue wherein the Bluetooth connection can drop while printing has been corrected, an issue seen
when handling larger formats, such as those using graphics
20. Bluetooth connectivity improved to better handle connection and disconnection events
21. Bluetooth pairing when using Android Nougat has been improved
22. Bluetooth pairing on the ZQ600 is now operating correctly.
23. Print quality on the ZQ600 where darkness did not match print quality on prior models has been
improved. Addressed in both legacy and non-legacy print modes.
24. The Applicator Mode End Print signal will now be active when:
a. The media moves backwards to reach a program position (^RS,Bxx)
b. Performing an RFID operation (^RS)
c. Both forward movement and programming (^RSFxx) are happening
25. The deactivation of the Void Signal and End Print Signal in Applicator Mode have been synchronized.
28
26. The Data Ready and Service Request signaling on the ZT600 in Applicator Mode has been altered to
duplicate how they operated on the Xi4 products
27. An issue with re-establishing a connection when closing and opening a socket connection from within a
ZBI program has been corrected.
28. ZBI handling of TCP connection close events has been improved
29. ZBI performance and throughput has been enhanced
30. The ZT4x0 cover light now retains its setting after the printer is turned off.
31. 802.11r abbreviated handshakes when roaming are now supported.
32. The Japanese translation of the text "About" has been corrected on front panels.
33. The German translation of the front panel message "Battery Low" has been corrected.
34. Incorrect data in the Zebra MIB has been corrected.
35. The HTTP server now correctly closes connections in all cases.
36. Association request packets for used in 802.11r are now correctly formatted.
37. The ZD510 now retains data from an ejected media cartridge until a new cartridge is inserted, allowing
data about the previous cartridge to be read.
Upcoming Changes:
• The rfid.adaptive_antenna command will be removed in the future “Version 7” of the Link-OS
Printer OS.
29
Link-OS v5.x Release Notes
This document applies to all Link-OS printer models. Exceptions are noted as needed.
Version Number: V85.20.16 (Based on Link-OS v5.2) .......................................................................................30
Build Number: 20.16Z .........................................................................................................................................30
Build Number: 20.15Z .........................................................................................................................................31
Version Number: V85.20.16 (Based on Link-OS v5.2)

• Version number V85.20.16 for the ZQ630 & ZQ630R models
Release Date: 8 April 2019
Changes
Initial release for the ZQ630 & ZQ630R models.
Build Number: 20.16Z

• Build number V81.20.16Z for the ZQ310 & ZQ320 models
• Build number V82.20.16Z for the ZR318/ZR328 models
Release Date: 15 January 2019
Changes
The Link-OS version has been updated to v5.3.
Issues Corrected
The ZQ300 battery management system has been updated. The reason for this change is that it may not
be possible to charge a battery that has been drained significantly below the operation level. This can
happen when the battery has not been charged for a significant time duration. This release adds the
capability of charging batteries that have been discharged significantly below the operational level.
30
Build Number: 20.15Z

Release Date: 12 October 2018
Changes
• The Link-OS version has been updated to v5.2.
• The Link-OS build number appears on the printer’s front panel.
• The build number (vxx.20.15z) can be viewed by pressing the ABOUT button on the main screen.
• Support for the 802.11G radio has been removed.
• The ThingMagic RFID system has removed support for the Korea 917300 tag channel.
• The ThingMagic RFID system does not support Morocco in region 8.
• Support for WLAN Ad Hoc mode has been removed, due to a change in the underlying radio's
software.
Frequently Asked Questions

technology trends and best practices. Version 5.2 contains improvements (such as enhanced WLAN
roaming) and fixes that could otherwise impact your business. We encourage updating to the latest
version to take advantage of the new features and fixes.
Link-OS v5 can be downloaded from the Zebra web site by using the link below and entering your
zebra.com/support
Link-OS V5.2 is a free upgrade.
Why is that?”
System releases but will not be backward-compatible with earlier Link-OS versions.
Desktop printers that are already running v5.1 or later will not support downgrading to printer OS
When and if an attempt is made to downgrade from v5.1 to an earlier build, the older build will not be
31
• On printers with a display screen, the message “Download Not Supported” will be displayed.
• The lights on the printer will behave in the following way – the Status light will turn solid red. The
other lights will be cycled on one at a time, changing the “on” light every second. (Exception: on the
ZD500 series printer, only the Status light will turn solid red.)
Issues Corrected
• WLAN roaming has been enhanced in the following ways:
• The printer will perform scanning one channel at a time
• Cleaning the Access Point black list will occur more quickly, to allow for high-AP density
environments.
• The potential for a disassociation/deauthentication loop has been eliminated
• Roam timing has been tuned to better schedule roam triggers and events.
• A condition where channel scanning could stop has been addressed.
• 802.11ac radio is now more stable during long idle times (2+ hours)
NOTE: 802.11r is supported only on the 802.11ac WLAN radio.
• Checks put in place to retain the County Code setting over a power cycle in Bluetooth only units.
• The startup process has been updated to allow for networks that do not deliver an DHCP address for
an extended time.
• A self-adjusting capability has been added to the Peel sensor so that the sensors settings are
preserved through a manual calibration.
• Power save has been defaulted to “off” on the ZQ600 series.
• The QLn will now report “sb” for the battery eliminator when the “battery type” command is used.
• If usb.host.lock_out is set to a “on”, the front panel menu item, CONFIG INFO to USB shall not be
displayed.
• The sequence of the DHCP addressing protocol has been corrected that all steps happen in the
appropriate order.
Upcoming Changes
• Zebra is announcing that the WLAN securities 40-bit WEP and 128-bit WEP will be removed in the
future “Version 6” release of Link-OS. This step is being taken to enhance product security. 40-bit WEP
and 128-bit WEP are still supported in Link-OS v5.2. They will be removed in v6.0 and beyond.
• Zebra is announcing that SHA-1 support will be removed in the future “Version 7” of Link-OS. This step
is being taken to enhance product security. SHA-1 is still supported in Link-OS v5.2. It will be removed
in Link-OS v7.0 and beyond.
32
V68 Printer OS
Release Notes
This document summarizes the following printer OS releases. For support, please visit zebra.com/support.
Link-OS 5 ............................................................................................................................................................34
V68.20.10Z .................................................................................................................................................34
Link-OS 4 ............................................................................................................................................................38
V68.20.01ZB ...............................................................................................................................................38
V68.20.01Z .................................................................................................................................................38
V68.19.15Z ..................................................................................................................................................43
V68.19.13Z ..................................................................................................................................................43
V68.19.10Z ..................................................................................................................................................46
V68.19.7Z ....................................................................................................................................................48
Link-OS 2 ............................................................................................................................................................51
V68.19.6Z ....................................................................................................................................................51
Link-OS 1 ............................................................................................................................................................53
V68.19.4Z ....................................................................................................................................................53
V68.19.2Z ....................................................................................................................................................54
V68.19.1Z ....................................................................................................................................................54
Non-Link-OS Firmware Builds ............................................................................................................................56
V68.18.8Z ....................................................................................................................................................56
V68.18.7Z ....................................................................................................................................................56
V68.18.6Z ....................................................................................................................................................59
V68.18.5Z ....................................................................................................................................................59
V68.18.3Z ....................................................................................................................................................60
V68.18.1Z ....................................................................................................................................................62
V68.18.0Z ....................................................................................................................................................63
V68.16.3Z ....................................................................................................................................................66
V68.16.2ZA ..................................................................................................................................................67
V68.16.2Z ....................................................................................................................................................68
V68.16.1ZA ..................................................................................................................................................68
V68.16.1Z ....................................................................................................................................................69
V68.16.0Z ....................................................................................................................................................69
33
V68 Printer OS Release Notes
Link-OS 5
V68.20.10Z
This Printer OS release includes all features of the previous build, unless noted otherwise. It is for use with
the following printer models:
• QLn220 • QLn220 Healthcare

• QLn420
Changes
• This is Link-OS version 5.
• Support has been added for the following features (see the PrintSecure Administration Guide for
details):
• IP Address Whitelisting for incoming print connections
• 802.1x, with support for user name, password and private key password
• User supplied certificates for 802.1x
• Transport Layer Socket (TLS)
• User supplied certificates for TLS
• User control TTLS with support for “pap”, “chap”, “mschap” and “mschapv2”
• HTTPS for the printer web pages
• User supplied certificates for HTTPs
• User Defined Gateway Ping intervals
• User supplied web sockets certificates
• New Service control commands
• OpenSLL v1.0.21
• The user supplied certificates for web sockets, TLSRAW and HTTPS can now be P12 formatted.
• 802.11r, also known as “Fast Roaming”, is now supported.
• The UCODE8 and UCODE8M RFID chips are now supported.
• The Visibility Agent shall now attempt to use the Google DNS and OpenDNS systems to resolve the
address when a static IP address is used.
• The SYSLOG now supports an entry for power down/reset
• A “BATTERY MISSING” alert has been added, for those printers that support it.
34
• The default for the power.sleep.timeout and power.inactivity_timeout have been changed on selected
products:
QLn series ZQ500 series iMZ series ZQ3 series

power.sleep.timeout N/A 20 minutes N/A 20 minutes
power.inactivity_timeout No change 10 hours no change 10 hours
• The Visibility Agent has been updated (see the AppNote on “Disabling the Visibility Agent” for complete
details):
• head.serial_number has been added.
• wlan.bssid has been added.
• device.location has been added.
• interface.network.active.speed has been removed.
• The Bluetooth system has been updated. This involves several changes:
• The LE GAP Device name – this GATT attribute will require pairing before it can be read.
• Bluetooth pairing bonds will be retained across upgrades, but not across printer OS downgrades.
• Printers with radios that support 4.1 or later now support Numeric Comparison pairing for Bluetooth
Low Energy pairing events. NOTE – only used if both devices support Bluetooth 4.1 and the Secure
LE connection protocol.
• SetGetDo changes. Several commands have changed:
• bluetooth.bonding – This command now applies to both Classic and Low Energy devices.
Previously, it was only possible to completely disable bonding for Classic devices.
• bluetooth.minimum_security_mode – This SGD now applies to both Classic and Low Energy
devices. Its functionality for Classic devices remains unchanged; its value affects LE security
modes as follows:
• 1: No encryption or authentication is required to access the Zebra Parser Service.
• 2: Encryption, but not authentication is required to access the Zebra Parser Service.
MITM protection is not required.
• 3 or 4: Encryption and authentication are required to access the Zebra Parser Service.
MITM protection is required, and “Passkey Entry” is the only pairing method that will allow
access.
35
• bluetooth.allow_non_display_numeric_comparison – This command now applies to both Classic

and Low Energy devices that do not have a display. Its functionality for Classic devices remains
unchanged; its value affects LE pairing as follows:
SGD Value I/O Capabilities Affect on LE

print (default) Display Only If Passkey Pairing is used, the printer will print out a small label
with the passkey to be entered on the remote device.
If LE Numeric Comparison is used, the printer will print out the
passkey and will auto-confirm the pairing request.
noprint Display Only If Passkey Pairing is used, the printer will not print out the
passkey.
If LE Numeric Comparison is used, the printer will not print out
the passkey, but will auto-confirm the pairing request.
off No I/O Passkey pairing is not allowed. Only “Just Works” pairing can
be used, and MITM protection is not possible. It is not possible
to reject the pairing request!
• Deprecated Commands:
Command Name Use This Command Instead

bluetooth.le.print_passkey bluetooth.allow_non_display_numeric_comparison
bluetooth.le.minimum_security bluetooth.minimum_security_mode
• LE Security Changes:
LE Minimum Security Value Previous Minimum Security New Minimum Security Value
Value
unauth_key_encrypt 1 2
auth_key_encrypt 1 or 2 4
none 1, 2, 3, or 4 No change
Issues Corrected
• ZBI now correctly handles output on the serial port.
• The printer now correctly handles repeated ~WR commands.
• Printer web page rendering has been made more reliable.
• Web sockets have been improved to better handle idle time, resets, connection retries/declines and
incidents where conn1 and conn2 are set to the same address.
• The WLAN system now correctly handles scenarios where an access point offers it un-allowed mixes of
security protocols (such as TKIP and HT and VHT support).
• The Unicode system now correctly handles shaping/rendering of Khmar character, when code
combination are used.
• The WLAN radio has been updated to better handle DFS channels.
• LPR throughput has been improved.
• The Bluetooth system can now better handle complex scenarios involving multiple connects and
disconnects.
36
• The GS1 Databar implementation has been enhanced to handle more data structure scenarios.
• Mirror Feedback files are now working correctly.
• The Protected Management Frames implementation has been updated to support newer radios.
• New SGD commands added to allow users to compensate for label layout variations.
"media.tof_tune"
• Range: -50 to 50. The media.tof limit (-400 to +400) will be applied to the sum of media.tof_tune and
media.tof_adjust.
• Example:
! U1 setvar "media.tof_tune" "5"
• Followed by a carriage return/line feed.
• The total top-of-form that is used by the printer will be the sum of media.tof (assuming 0 for this
example) and media.tof_tune. Given the example command above, that would be 5.
• Suggested starting value when migrating from RW to ZQ500: “-13”.
• Not affected by a printer default.
"print.vertical_dpi_adjust"
• Range: 95.0 to 105.0.
• Default: 100.0 (no change in y-coordinate or height of print fields)
• Example:
! U1 setvar "print.vertical_dpi_adjust" "97.8"
• When a label height is specified as 2000, it will be changed to 1956 (97.8% of 2000) before printing
the label. If a field y-coordinate is specified as 1000, it will be change to 978 (97.8% of 1000) before
processing the field.
• Suggested starting value when migrating from RW to ZQ500: “98.4”.
37
Link-OS 4
V68.20.01ZB
This firmware includes all features of the previous release, except where noted otherwise. It is for use with

• QLn420
Issues Corrected
The WLAN system has been updated to fix the “Key Reinstallation Attacks” issues reported against the
WPA/WPA2 WiFi protocols.
These issues are detailed at krackattacks.com/
Zebra maintains a website with details on this issue at:
zebra.com/us/en/support-downloads/lifeguard-security/lifeguard-krack.html
V68.20.01Z
This firmware includes all features of the previous V68.19.15Z release, except where noted otherwise. It is
for use with the following printer models:

• QLn420
Changes
• Link-OS version updated to v4.0.
• Support has been added for a Visibility Agent. This new feature can connect a networked Link-OS
printer to Zebra’s Asset Visibility Service (AVS). The Asset Visibility Service is a Zebra-managed
service offering that provides Zebra partners and customers ‘at-a-glance’ visibility to analytical insights
about their device health, utilization, and performance. When Link-OS v4 printers are connected to a
wired or wireless network, they will attempt to connect to the Asset Visibility Service by default. When
successfully connected, the printer sends approximately 5 Kbytes of data per day (depending on how
many alert events happen per day).
• Data printed on any labels, tags or receipts are not transmitted to the Asset Visibility Service. The
printers only communicate predefined settings on a scheduled basis. The printer sends Discovery
Data and Settings and Alerts Data. The settings that are transmitted are listed below in the form of
Set-Get-Do commands and are detailed in the Zebra Programming Guide.
• The printer uses an encrypted, certificate-authenticated web socket connection to connect to the
ZPC. NOTE: This is the same connection type that is typically used when you connect to an
e-commerce or banking site.
38
• The Visibility Agent can be turned off using a Set-Get-Do Command. Using your preferred software
or Zebra Setup Utilities, send the commands below to configure and validate the Asset Visibility
Agent settings. You can download Zebra Setup utilities at zebra.com/setup.
weblink.zebra_connector.enable
Turns the Asset Visibility Agent on or off. Additional information can be found in the App Note. See
zebra.com/us/en/products/software/barcode-printers/link-os/application-notes.html.
Values: "on" or "off"
Default Value: "on"
To send the commands:

1. Send the following command to Opt Out (disable the connection to ZPC and the Asset Visibility
Service):
! U1 setvar "weblink.zebra_connector.enable" "off"
2. Send the following command to validate that you have opted out:
! U1 getvar "weblink.zebra_connector.enable"
The printer should respond with "off".
NOTE: Be sure to include a carriage return/line feed after sending a command to the printer.
If the Visibility Agent is on, there are two data types that the printer can send to the AVS platform –
Discovery Data and Setting/Alert Data.
Discovery Data
This information is sent when the printer connects to the ZPC. The following printer settings are
transmitted:
Printer Settings
device.unique_id media.type device.oem.model_name
ip.dns.domain media.thermal_mode appl.name
ip.active_network media.printmode device.location
mac_raw odometer.total_label_count zpl.system_status
ip.protocol odometer.media_marker_count1 ip.addr
ip.netmask odometer.media_marker_count2 ip.ftp.enable
ip.gateway label_queue.batch_label_cnt ip.lpd.enable
ip.port label_queue.format_counter ip.tcp.enable
device.pnp_option zbi.enabled ip.udp.enable
device.languages zbi.state ip.http.enable
device.cpcl_formatting_commands_disable zbi.revision ip.smtp.enable
head.resolution.in_dpmm head.width.in_dots ip.pop3.enable
zpl.label_length ip.port_json_config ip.snmp.enable
ezpl.print_width appl.link_os_version ip.telnet.enable
media.darkness.mode device.friendly_name weblink.enable
39
Settings and Alerts Data

This information is sent by the printer at the schedule listed in the table below. The following printer
settings or alerts are transmitted:
Printer Settings
At connection: At connection: When the Alert occurs:
weblink.zebra_connector.version device.bluetooth_installed PAPER OUT
device.product_name odometer.media_marker_count RIBBON OUT
print.tone_format media.type, ezpl.media_type HEAD ELEMENT BAD
power.percent_full interface.network.active.speed SUPPLY TOO HOT
power.serial_number_string HEAD OPEN
power.manufacture_date HEAD COLD
power.cycle_count Every Hour: HEAD TOO HOT
power.device_name power.percent_full CUTTER JAMMED
power.full_charge_capacity wlan.signal_strength COLD START
power.date_first_used odometer.total_print_length
interface.network.active.ip_addr interface.network.active.speed
wlan.signal_strength Once A Day:
odometer.total_print_length power.cycle_count
odometer.rfid.valid_resettable Every 6 Hours: power.device_name
odometer.rfid.void_resettable print.tone power.full_charge_capacity
memory.flash_size print.tone_zpl odometer.total_label_count
memory.flash_free media.speed odometer.rfid.valid_resettable
device.ltu_installed zpl.label_length odometer.rfid.void_resettable
device.cutter_installed memory.flash_free
device.rewinder_installed odometer.media_marker_count
media.type
ezpl.media_type
• Front Panel Batch Counters have been made available. They can be turned on by using the SGD
command display.batch_counter.
• Web sockets connections now support SHA2 certificates. The printers will continue to support SHA1
certificates until Link-OS v5 is released (in 2017). At that time, the printers will no longer support SHA1
certificates, in accordance with privacy best practices.
• Alerts are no longer displayed over the Home menu to enhance readability.
• New Set-Get-Do Commands were implemented. Refer to the Zebra Programming Guide for details on
each command.
• head.resolution.in_dpi
• file.capture_response.begin
• file.capture_response.end
• file.capture_response.destination
• device.command_override.add
• device.command_override.clear
40
• device.command_override.list
• device.command_override.active
• weblink.zebra_connector.version
• weblink.zebra_connector.enable
• weblink.zebra_connector.proxy
• weblink.zebra_connector.authentication
• weblink.zebra_connector.authentication.add
• weblink.zebra_connector.authentication.remove
• weblink.zebra_connector.authentication.entries
• wlan.wpa.timecheck
• wlan.rts_cts_enabled
• display.batch_counter
• device.set_clock_to_build_date
Issues Corrected
• The SGD command power.low_battery_timeout_alt is now read/write.
• Bluetooth connectivity has been improved so that it will not disconnect during a network reset (~WR).
• When using the Dual Radio, the Bluetooth radio will remain active even if the WLAN radio is not.
• The SNMP zbraOptUnsAlertCondition and zbrOptUnsAlertsEntry response strings have been
extended to include 1023 characters.
• The Japanese and Korean front panel menus have been adjusted to eliminate character overlaps.
• SNMP Print Job Completed reporting has been enhanced when using the Pause Alert.
• The ZBI WRITE command has been corrected to count all data written to the system.
• The EPL URH and URL commands will now return a value in meters.
• The Mirror system timing has been altered to include a retry, so as to improve file writing performance.
• EPL has been enhanced to handle images larger than the label size.
• The command zpl.zpl_override has been eliminated; use the device.command_override commands
instead.
• The printer will now come back on-line after being rebooted while in the cradle when the battery is fully
charged.
• The printer will now feed to the SET-TOF defined position when that setting has been set, and the FEED
button is pressed.
• The Mirror system will now accept the return code 125 in addition to the return code 150, in order to
support IIS7 and FileZilla servers.
• The Mirror system now supports time and date stamping used by IIS7 and FileZilla servers.
• Firmware updating when using both Profile Manager and either IIS7 or FileZilla has been optimized to
avoid conflicts.
• Wi-Fi roaming and Protected Management Frames (PMF) support have been improved.
• Charging while the printer is turned on has been optimized to eliminate unneeded charge cycles.
41
• Memory management during printing has been optimized for cases where a .TTF font, graphics, and
inverted orientation printing are being used.
• The JSON implementation of the usb.mirror.feedback.odometer and
ip.mirror.feedback.odometer commands now have values of READ_WRITE_ACCESS.
• The JSON implementation of the zbi.state command has been changed from a string type to an
enum type.
• The EPL command oR0,0 is now supported..
• The Czech menu will now use the word INCHES.
• Socket connections on ZBI have been optimized to avoid a connection not ending when it should.
• The CHARGING TEMP FAULT message system has been optimized to be more accurate.
• The JSON implementation of interface.network.active.speed is now treated as an integer.
• APPLICATOR mode will be offered and selectable, and the printer will use APPLICATOR paper
movement behavior while in the mode; however since the printer does not have an applicator option,
the printer will not wait for applicator signals.
• The label feed length after a calibration will now be updated to use the newly calibrated length.
• The range for ip.discovery.port is now 1 - 65535.
• The range for zpl.label_length has been corrected in the allconfig.
42
Link-OS 3
V68.19.15Z

• QLn420
Changes
• The wireless settings commands only support non-control ASCII characters.
• FTP PORT commands are supported when the port number requested is above 1023 and the IP
address being requested is the same as that of the device initiating the connection.
Issues Corrected
• Network Time Protocol settings syntax checking has been enhanced.
V68.19.13Z
Release Date: 31August 2015

• QLn420
NOTE: When updating from firmware V68.16.3Z or any earlier version, users must first update the printer
to V68.18.6Z, before updating to any later versions. We also recommend that users power cycle the printer
after the update to V68.18.6Z, before moving to any later versions.
In addition, when updating from firmware V68.18.1Z or any earlier version, we recommend users
default the printer after updating to a later firmware version. To default the printer, send these ZPL
commands to the unit:
^XA^JUF^XZ
^XA^JUS^XZ
Wait 5 seconds after sending these command and then power cycle the printer.
43
Changes
• Link-OS printers now support downloading PEM and DER formatted WLAN certificates in the P12
format for the TLS, TTLS and PEAP security types. Additionally, P12 formatted certificates are now
supported for downloading private keys and client certificates. For more information, see the App Note
“Direct WLAN Cert Downloading.”
• Front Panel passwords are now supported on the QLn220 and QLn320 Healthcare units – and on the
QLn420. The password level can be set from the Tools menu.
• The new Zebra logo is now used on the front panel, web pages and two-key report.
• The printers will now store information related to the state of the devices sensors and internal printer
operations which may be accessed and used by Zebra for the purpose of improving the products
performance and readability. For more information, please contact softpm@zebra.com.
Issues Corrected
• The "netmanage.avalanche.agent_addr" command will now accept a DNS value.
• The OID: .1.3.6.1.4.1.10642.200.14.5.0 (zql-power-low-battery_shutdown) response has been
corrected.
• The printers will now accept a .GRF image larger than 100KB.
• The Power Smart Print Technology version number will now report in the correct format.
• The ZPL implementation of the Datamatrix barcode has been enhanced to support more combinations
of standard ASCII and extended ASCII character strings.
• The Head Open detection system has been enhanced to avoid false head open reports.
• The Battery Authentication system has been enhanced to improve “time to ready” performance.
• TTF font handling in CPCL has been enhanced to improve performance.
• CPCL TTF character mapping now uses 1252/Latin 1 to locate characters for print events.
• Label Bar and/or Gap detection during backfeed events has been enhanced to ensure complete label
printing.
• Charging has been enhanced to optimize battery health.
• JSON parsing has been enhanced to better handle slow transmissions to the printer.
• Rendering time for ZPL generated circles, boxes with rounded corners and diagonal lines has been
enhanced.
• Font handling has been improved to ensure that when a new font replaces an existing font, the
character mapping is correctly updated.
• The ^HZO response now places a drive letter in the <OBJECT-DATA> reply.
• The ^GFA command will no longer produce a stretched image when the last line of the encoded
graphic is a “,” or a “!”.
• The time the Bluetooth system will wait for a connection has been extended to accommodate the needs
of more devices.
• ZBI program throughoput has been enhanced.
• The Cloud Connect web sockets system has been optimized to improve throughput.
• The Cloud Connect web sockets has been optimized to better handle large file (1MB+) downloads from
the printer to a host system.
• The USB implementation has been enhanced to optimize bi-directional communication.
44
• The Bluetooth system has been enhanced to support scenarios where the Master device is sending
data immediately after creating a connection.
• In order to improve throughput, the WLAN system will now use "CTS to Self" for the default HT mode.
The system can be set to use "RTS-CTS" by using the "wlan.rts_cts_enabled" command (default is
"off").
• Checksum validation during CPCL downloads has been altered to accept images from the
Multiplatform SDK.
• The printer will now stay on when the power.inactivity_timeout is set to a non-zero value and the unit is
plugged in or in a powered cradle.
45
V68.19.10Z
• QLn220 • QLn420
• QLn320 • QLn HC
^XA^JUF^XZ
^XA^JUS^XZ
Changes
• Wi-Fi certification for this model is now based on the Standard Zebra Wireless driver
• Ad-Hoc wireless is now supported.
• Opportunistic Key Caching (OKC),”Fast Roaming” is now supported on WLAN connections.
• The Network Time Protocol (NTP), which allows setting the printers clock based on a time server, is
now supported.
• Country support for RFID has been expanded.
• A secondary Bluetooth® channel for management tasks has been added.
• The total label count odometer value has been added to the configuration label .
• "Qatar" is now a supported value for the "wlan.country_code" SetGetDo command on the QLn220
and QLn320 printers.
• The Avalanche client now supports reporting a successful printer OS update.
• The printer will now validate that user-assigned network port number assignments do not conflict with
each other.
• The OpenSSL version the printers use is now v1.0.0m.
• The "device.jobs_print" SetGetDo command is now supported.
• The "power.low_battery_warning_raw" command now uses use a consistent implementation across
the Link-OS Mobile product line. If updating an existing printer, users will have to send the
! U1 setvar "device.restore_defaults" "power"
command to use this new implementation.
• The device.languages command default for the QLn220 HC and QLn320 HC printers is now
"epl_zpl" .
• The Battery Eliminator is now supported.
46
• Users can now control if the network activity LED on the QLn cradle blinks by using the SetGetDo
command "internal_wired.activity_led". There are two settings, "blink" or "solid"; "blink" is
the default.
• The Link-OS version is now v2.5.
Issues Corrected
• Throughput for small label (1.5" long and shorter) has been enhanced.
• Support for CCX is now available via the Zebra Development Services team, so that implementations
can be tailored to individual network needs.
• ^HZA responses when running ZBI programs have been corrected to include all expected data.
• WML has been corrected to consistently show messages positioned in the bottom center of the screen.
• ZBI processing of formats larger than 32K has been corrected.
• The EPL speed command ("S") will now set the print speed, slew and backfeed rates.
• The value set by the "Q" command will now be used in both ZB and ZT modes.
• The printer will now respond to an "Escape H" command, when it’s received at the end of a ZPL format.
• The WLAN MAC address will now be consistently reported after a power up event when a new main
logic board has been installed .
• The ~JP command now correctly pauses the printer.
• EPL 'p' commands will no longer effect subsequently printed ZPL formats.
• The Czech and Russian translations on the front panel of the QLn420 have been updated.
• Graphics sent to the printer using the EPL command "GM" are now supported.
• The bluetooth.bonding setting will now be returned via either a JSON Bluetooth branch or allconfig
request.
• MAC address reporting has been enhanced to ensure address is correctly reported at startup.
• Management of Bluetooth connections has been enhanced to ensure data integrity when new
connections are being made while data from a prior connection is still being processed.
• The E:SYSLOG.TXT file will only be saved to the E: drive when the
"device.syslog.save_local_file" setting is set to "yes".
• An UCC/EAN128 barcode, using mode D, which contains an odd number of digits following a subset
A/B section will now print correctly.
• Spaces are now allowed in "netmanage.avalance.set_property" SetGetDo commands.
• Recalling formats that contain serialized fields with XML is now functional.
• Media sensing calibration has been enhanced to increase accuracy.
• Media cover open (print head open) detection has been improved.
47
V68.19.7Z
This firmware is for use with the following printer models:
• QLn220 • QLn420
• QLn320 • QLn HC
This firmware includes all features of the previous V68.19.6Z release.
^XA^JUF^XZ
^XA^JUS^XZ
Changes
• Added support for the QLn HC (Healthcare) series.
• Added support for the EPL command language:
• The device.languages SetGetDo command now supports the values "epl_zpl" and "epl".
• The printer defaults to "hybrid_xml_zpl" for the device.languages setting on QLn 220, QLn 320,
QLn420 units, and to "epl_zpl" on QLn HC units.
• The setting may be changed via the COMMAND LANGUAGE menu in the LANGUAGES menu on the
QLn420 and QLn HC series units. The default password is "1234".
• An alternate Plug and Play string for EPL has been added.
• Added support for Bluetooth® connectivity to iOS devices.
• This applies to printers with SKU designators Qxx-xxNxxMxx-xx and
Qxx-xxCxxMxx-xx that are loaded with V68.19.7Z or later.
• Control panel menu changes:
• MFI CAPABILITY added to the Bluetooth menu.
• WLAN STATUS added to the QLn420 and QL HC Network menu.
• AP MAC ADDRESS added to the QLn420 and QL HC Network menu.
• COMMAND LANGUAGE added to the QLn420 and QL HC Language menu.
• BACKLIGHT TIMEOUT in the QLn420 and QL HC Tools menu is now password protected. The default
password is "1234".
• MEDIA TYPE in the QLn420 and QLn HC Settings menu is now modifiable and password protected.
The default password is "1234".
• SetGetDo commands added to control passwords on QLn420 and QLn HC series printers
48
• Bluetooth Pairing QR code:

Press the arrow up key from the printer’s home screen to display a QR code
containing the printers Bluetooth MAC address.
If Bluetooth is enabled, a QR Code containing the printers Bluetooth MAC address will display. If the
printer has an IP address and Bluetooth is enabled, pressing the up arrow will display a QR code
containing the IP address - and pressing the right or left arrow key will then display a QR Code
• IP Address Pairing QR code:
If the printer has an IP address, press the arrow up key from the printer’s home screen to display a
QR Code containing the IP address.
If the printer does not have an IP address, the QR Code containing the IP address will not display. If
the printer has an IP address and Bluetooth is enabled, pressing the up arrow will display a QR code
containing the IP address, and pressing the right or left arrow key will then display a QR Code
• The two key config report now includes a line that begins with PCC and ends with the stock keeping
unit (SKU) number of the printer as assigned at the point of manufacture.
• Syslog support added.
• The following SetGetDo commands were added or updated:
display.suppress_all_alerts Temporarily suppresses alerts.

Choices: off, on
Default: off
display.status_bar_suppress Temporarily suppresses the status bar.
Choices: off, on
Default: off
device.syslog.clear_log Clears the local syslog file.
device.syslog.configuration Specifies the location for the syslog reports to be
recorded.
device.syslog.enable Enables the syslog file to record system messages.
Choices: off, on
Default: off
device.syslog.entries Displays the contents of the local syslog file.
device.syslog.log_max_file_size Specifies the maximum size of the syslog file.
Choices: 10000-400000
Default: 10000
device.syslog.save_local_file Saves the contents of the local syslog to E:SYSLOG.TXT.,
Choices: no, yes
Default: no
display.password.current Specifies the current password on QLn420 and Qln HC
printers
Choices: 0 to 9999
display.password.length Specifies the length of the display password on QLn420
and QLn HC printers
Choices: 1 to 20
49
display.root_wml Controls which index.wml file to use:

For QLn220 and QLn320 units, the default value is
"INDEX320.WML"
For QLn420 and QLn HC units, the default value is
"INDEX420.WML"
ip.tcp.nagle_algorithm Controls the Nagle algorithm.
Default: "enable"
See RFC 896 for further details:
http://tools.ietf.org/html/rfc896
power.inactivity_timeout Now supports "up" and "down" values, for use in menus.
wlan.poor_signal_threshold Controls when the printer indicates it is receiving a poor
signal.
Range:  to 100
Default: 0
Issues Corrected
• Bluetooth passwords can now be up to 16 characters long.
• Line mode in CPCL corrected so that it does not require a carriage return/line feed after barcode fields.
• The SetGetDo command device.macro_get was corrected to support pre-pending and post-pending .
• Bluetooth radio now supports interaction with devices that use credit-based flow control.
• The SetGetDo command "input.capture" "run" now captures all incoming data.
• Bluetooth radio performance enhanced to support out of order packet streams.
• Corrected an issue where the control panel content could be temporarily display illegibly during an alert
condition.
• Corrected an issue where the printer can turn off before processing transmitted data when a serial port
DTR low event occurs.
50
Link-OS 2
V68.19.6Z
• QLn220
• QLn320
• QLn420
This firmware includes all features of the previous V68.19.4Z release.
^XA^JUF^XZ
^XA^JUS^XZ
Changes
• The Link-OS version number is now 2.0.
• Added full support for Profile Manager features. Upgrade to this firmware version to use printers with
the Profile Manager app. This firmware is embedded in the Profile Managers Resources system to
facilitate updating.
• Added support for DHCP option 43. The feature allows the printer to obtain the settings used to control
Cloud Connect weblink connections or Mirror events as part of receiving a DHCP assigned IP address.
This requires that DHCP Option 60 is not empty and that ip.dhcp.auto_provision_enable is set to
"on".
The package of Cloud Connect/weblink information sent from the DHCP server in the Option 43
response can include the:
• Server address
• Authentication server name
• User name and password for proxy logins
The package of Mirror information sent from the DHCP server in the Option 43 packet can include the:
• Server address
• Mirror path
• Mirror feedback path
• Mirror appl path
• Mirror mode
Consult the Programming Guide for more information.
51
• Added a "default" field to the "allconfig" JSON response for each setting.
• The Cloud Connect weblink connection will now send a websocket ping to the connected server every
60 seconds. If no response is received after three attempts, the connection will be closed.
• The Cloud Connect weblink connection now logs the servers certificate serial number and fingerprint.
• Additional bits added to the ~HQES response and Advanced Discovery packet.
• A new setting weblink.ip.connX.num_connections has been added. This setting shows the number
of established connections. The control channel counts as 1 as well as all other sub channels (echo,
raw_port, json_config). This is getvar only settings with a max value that is the same as the
max_number_connections. Consult the Programming Guide for more information.
• A new group of settings for position have been added. These allow users to manually set latitude,
longitude and altitude values on the printer. Consult the Programming Guide for more information. The
new settings are:
device.position.latitude in degrees min/max: -90.0/90.0
device.position.longitude in degrees man/max: -180.0/180.0
device.position.altitude in meters min/max: -10000.0/406700000.0
device.position.accuracy in meters min/max: 0.0/406700000
Issues Corrected
• JSON will now return a null instead of a "?" for settings that do not exist on the device.
• The ip.dns.domain or ip.dns.servers values can now be set while IP addressing is set to permanent.
• PCX graphics handling has been improved to handle additional scenarios.
• Scalable font field handling improved.
• Handling of Bluetooth remote device disconnect events improved.
• odometer.user_label_count can be set to "0".
• Ping response times have been enhanced.
52
Link-OS 1
V68.19.4Z
• QLn220
• QLn320
• QLn420
This firmware includes all features of the previous V68.19.2Z.
^XA^JUF^XZ
^XA^JUS^XZ
Changes
• The QLn420 battery eliminator is now supported.
• Additional 802.11n country codes supported: Bahrain, Belarus, Croatia, Lebanon, Oman, Serbia, Sri
Lanka, Uruguay, Venezuela, Vietnam
• This release includes support for simultaneous 802.11 a/b/g/n and Bluetooth Dual Radio.
NOTE: The Dual radio option is only available on the n radio configuration. By default, the Bluetooth radio
is disabled on printers that support dual radio. The Bluetooth radio can be enabled by using the
bluetooth.enable command. When both the WLAN and Bluetooth radios are enabled, the
wlan.power_save feature will be turned off.
Issues Corrected
• Peel sensor performance has been corrected to support additional use cases
• Enhanced memory management to resolve text field not printing issue.
• To support applications created for the QLPlus, if the printer is in CPCL synchronous mode with “on out
of paper” set to PURGE and Retry set to “1”, the printer will discard the current label when the printer
runs out of paper or the head is opened.
53
V68.19.2Z
Release Date: 15 February 2013
• QLn220
• QLn320
• QLn420
This firmware includes all features of the previous V68.19.1Z and V68.18.8Z.
^XA^JUF^XZ
^XA^JUS^XZ
Issues Corrected
• Printer will no longer skip labels when ^LT and ^PQ are used in a format.
V68.19.1Z
• QLn220
• QLn320
• QLn420
^XA^JUF^XZ
^XA^JUS^XZ
Issues Corrected
NA
54
Link-OS Features
Initial release of Link-OS support.
• Data Capture to SGD
• Unsolicited alerts for SGD changes
• HTTP POST transport for unsolicited alerts
• SGD change log
• ZBI events for SGD changes
• User Variables Port 9200 - SGD Channel
• Cloud Connectivity
55
Non-Link-OS Firmware Builds

V68.18.8Z
Issues Corrected
• The printer will now correctly retain and use TONE settings.
^XA^JUF^XZ
^XA^JUS^XZ
Changes
• NA
V68.18.7Z
Release Date: 3 December 2012
^XA^JUF^XZ
^XA^JUS^XZ
Enhancements
• BT: Add support for BT 3.0 radio (QNx-xxCxxxxx-xx)
• BT: Add SIG certification for BT 3.0 radio (QNx-xxCxxxxx-xx)
• BT: Updated Bluetooth driver
• BT: Add support for Bluetooth Key Bonding, see below for details
• LCD: Add support for 2-byte WML and international fonts on the display
• LCD: Add ability to flip the display, see below for details
• 802.11: Updated driver and improved roaming algorithm for 802.11 n radio (QNx-xxNxxxxx-xx)
56
• 802.11: Add WIFI certification for 802.11 n radio (QNx-xxNxxxxx-xx)

• 802.11: Add CCXv4 ASD certification for 802.11 n radio (QNx-xxNxxxxx-xx)
• 802.11: Add support for additional 802.11 n countries, see below for details
Issues Corrected
• CPCL: Form Feed character (0x0C) not processed correctly
• SGD: wlan.allowed_band parameter incorrectly reset by device.restore_defaults command
• 802.11: Incompatibility with Motorola WS5100 using WEP multicast key
• 802.11: Resource Location Server (RLS) address (option 11) is not requested in DHCP
discovery packet
Changes
• 802.11: Removed support for Ad Hoc mode
• 802.11: Removed support for WEP with 802.11 i authentication (WEP with PSK is still supported).
Bluetooth® Key Bonding

With the advent of the Bluetooth Simple Secure Pairing (SSP) algorithm, connecting two devices that both
support BT version 2.1 (or higher) may take longer. The connection time between the QLn and terminal
can take up to 8 seconds, compared with roughly 2 seconds if the terminal is BT 2.0 or earlier. The
additional delay is due to the complex, but more secure, key exchange protocol required as part of SSP.
Prior to SSP, Bluetooth devices used pre-configured PINs. Except for the first time any two devices are
paired; the key bonding feature avoids the additional delay by saving and reusing the encryption key. Up to
15 encryption keys are stored in printer memory, corresponding to 15 unique printer–terminal pairs. If the
printer is paired with a 16th terminal, the oldest key used is replaced with the new one. The entire key
cache can be cleared for security purposes.
Examples showing how to turn the key bonding feature on (default) or off, get the current status, and clear
the cache are shown below:
! U1 setvar "bluetooth bonding" "on"

! U1 setvar "bluetooth bonding" "off"
! U1 getvar "bluetooth bonding"
! U1 do "bluetooth.clear _ bonding _ cache" ""
If the key cache is cleared all previously established encryption keys are lost, and it will be necessary to go
through the key exchange protocol the first time each new terminal is paired with the printer.
Display Flip
It is now possible to invert the orientation of the display (180°) to make it easier to read in some
installations, e.g. when mounted to a wall or a fork lift. It can also be configured to automatically invert
when docked in a cradle. It is necessary to restart the printer after changing the orientation setting.
57
Examples showing how to set the display to normal (default), inverted, and automatic mode are shown
below. Remember to send the device.reset command after changing the value. The final example shows
how to read back the current status:
! U1 setvar "display.orientation" "normal"
! U1 setvar "display.orientation" "inverted"
! U1 setvar "display.orientation" "auto"
! U1 do "device.reset" ""
! U1 getvar "display.orientation"
Configuring the 802.11 n Country Code

When configuring the 802.11 n radio it is important to configure the wlan.country_code parameter in order
to define the channels allowed in that country, group of countries, or region. The list of country options is
determined by the wlan.region code parameter, which is set at the factory based on the Group designator
in the printer SKU, as indicated by the “?” as follows: QNx-xxxx?xxx-xx. The choices are shown in the table
below:
Group wlan.region_code wlan.country code choices

0 usa/canada usa/canada
J japan japan
E,L,A,B rest of world not selected, argentina, mexico, brazil, costa rica, nicaragua,
peru, europe, russia, ukraine, turkey, south africa, israel, saudi
arabia, uae, egypt, jordan, singapore, australia/nz, korea, china,
taiwan, india, malaysia, philippines, thailand, hong kong,
panama, bolivia, colombia, el salvador, guatemala, honduras,
chile
For Groups 0 and J the wlan.country code is set at the factory as shown above, and no changes are
permitted. For Groups E, L, A, and B the wlan.region_code is set to “rest of world”, and the default value for
wlan.country_code is “not selected”. In these cases it is necessary to configure the wlan.country_code
parameter for proper operation. Examples showing how to get the region and country codes, and how to
set the country code are shown below:
! U1 getvar "wlan.region _ code"

! U1 getvar "wlan.country _ code"
! U1 setvar "wlan.country _ code" "europe"
! U1 setvar "wlan.country _ code" "australia/nz"
! U1 setvar "wlan.country _ code" "brazil"
The current country code choices can be generated by sending the following command to the printer:
! U1 getvar "wlan"
Notes
• EU/EFTA countries should set the country code to “europe”
• The choices provided do not imply the printer is certified in those countries, rather that the printer knows
what channels that country, group, or region allows
• SGD conventions dictate that all choices are lower case text only
• For USA, Canada, and Japan the wlan.country_code parameter is set at the factory, no changes are
allowed
58
• If wlan.region_code is set to “rest of world”, it is not possible to configure the

wlan. country_code to usa/canada or japan.
• Setting the wlan.country_code parameter to an incorrect value based on the installed location may
result in incorrect operation
• If the wlan.country_code is not configured the 802.11 n radio will default to only use channels 1 – 11 in
the 2.4 GHz band
V68.18.6Z
^XA^JUF^XZ
^XA^JUS^XZ
Enhancements
• Improved 802.11 n noise floor performance. Affects QNx-xxNxxxxx-xx configurations only.
Issues Corrected
• Files sent from ZBI-Developer will not remain in flash after a power cycle.
V68.18.5Z
Enhancements
• Add new auto-recovery feature (see details below).
Issues Corrected
• N/A
Auto-Recovery
A new Auto-Recovery feature has been added that will reinstall the firmware if an issue is detected during
start up. If a problem is detected the printer will display “Decompressing Files”, then “Writing Files to Flash”
and then “Finishing Install” on the LCD, after which the printer will restart. The firmware version on the
printer will remain the same after Auto-Recovery.
NOTE: Data sent to the printer during Auto-Recovery may not be received or processed.
59
V68.18.3Z
Enhancements
• Add support for 802.11 n radio for EU/EFTA countries, SKU QNx-xxNxExxx-xx
• Ability to print Aztec barcode with Bluetooth mac address from LCD
• Add support for Wavelink Avalanche (over Ethernet or WLAN)
• CPCL: Add support for ESC-JRU command
• Mirror: Add ability to show progress during mirror updates
• Mirror: Add support for a common application directory (see below)
• Mirror: Improved download performance
• Mirror: Increase maximum number of download files from 100 to 300
• Increase the max top of form setting from 89 to 120 for the QLn320 (see below)
• SGD: Change default value of the usb.halt parameter from yes to no
• SGD: Added new parameter media.feed_skip (see below)
• Updated Bluetooth Stack to version 4.2.0
Issues Corrected
• CPCL: PRESENT-AT not performed on ! U1 FORM
• CPCL: 4 dot row registration error when using black bar media (see below)
• CPCL: PRESENT-AT not undone for first label after a power on
• DUMP mode not working correctly
• LCD: battery icon may falsely display fully charged status during startup
• PRINT: skipping labels with ½ inch (12 mm) label stock
• PRINT: first label printed is not registered correctly
• SERIAL: printer may turn off (using DTR) before executing all transmitted data over the serial port
• ZBI does not consume button events
• ZPL: printing cut off for internal directory and ZPL status reports on the QLn220
Common Mirror Application Directory

A new SGD parameter ip.mirror.appl_path has been added which allows a common firmware directory for
those cases when multiple applications / settings are used. This new command will define the “common
firmware directory” for printers to search as a secondary firmware location. This eliminates redundancy
and reduces the total amount of storage space required on the server when multiple mirror directories are
used.
Behavior
• If the new "ip.mirror.appl_path" is blank (i.e., not configured), then the printer’s mirror behavior is
the same as it is today. This is the default.
60
• If the value is anything other than blank the printer searches the directory defined in this path if there is
no firmware file in the standard mirror path (defined by ip.mirror. path).
• If the firmware in the "ip.mirror.path" matches what is currently on printer, then the printer does not
check for firmware in the "ip.mirror.appl_path".
Examples
! U1 getvar "ip.mirror.appl_path"
! U1 setvar "ip.mirror.appl_path" "pathname"
Increase the Maximum TOF Setting for the QLn320

The maximum Top Of Form (TOF) setting for the QLn320 (only) has been increased from 89 to 120 dot
rows. The maximum TOF setting for the QLn220 remains at 89. This new capability requires both
hardware and firmware changes, and allows printing on media with the black bar up to 120 dot rows below
the beginning edge of the label. The hardware changes are cut in on a rolling basis starting
(approximately) with printers built in November 2012. The firmware changes in this release are designed to
be backwards compatible, meaning it automatically detects which hardware is present and prints
identically on either version. Note that loading older firmware (prior to V68.18.3Z) on printers built after the
date listed above is not supported and will likely result in incorrect registration.
New SGD Parameter media.feed_skip and CPCL Registration Error

This SGD parameter controls the number of dot rows to skip after the trailing edge of the black bar or gap,
for CPCL labels only. This parameter is the saved (after a power cycle) version of the second parameter in
the CPCL SETFF command (see the SETFF command description in the CPCL programming manual for
more details). The default value is 5.
Note that in this release a 4 dot row registration error was corrected for CPCL labels when using black bar
media. Starting in this release, CPCL labels will begin printing
4 dot rows (~ 0.5mm) closer to top edge of the label. This is likely not visible to most users. However, if this
should not be the case the media.feed_skip parameter can be used to compensate. To do so set the value
to “9”, and this will add back the extra 4 dot rows removed by the firmware. Since this parameter does not
exist in earlier versions of firmware, adding this setting to a configuration file would have no impact for
those versions. Such a change would allow for common registration behavior across firmware versions.
! U1 getvar "media.feed_skip"
! U1 setvar "media.feed_skip" "9"
Potential Issue When Updating Firmware to V68.18.3Z

Updating printers that were initially built with firmware prior to this release may cause the printer to feed a
label on power up. Printers originally built with the V68.18.3Z release will not have this behavior. To
correct this issue such that no feed is performed at power up send the following commands (including
CR/LF after each line) to the printer:
^XA^JUF^XZ
^XA^JUS^XZ
Note that this will reset the printer’s configuration. Any previously installed customer unique configuration
commands will need to be re-applied.
61
V68.18.1Z
Enhancements
• Add support for 802.11 n radio, SKU QNx-xxNxxxxx-xx (US and CA only)
• Improved USB performance
• Improved 802.11 and Ethernet file download performance
• Printer no longer reboots when docked or undocked from Ethernet cradle
• SGD: added file.dir_format command, see details below
Issues Corrected
• CPCL: change ON-OUT-OF-PAPER default from PURGE 2 to PURGE 1
• CPCL: Performance degradation with large number of references to CPF fonts
• CPCL: DIR commands incorrectly lists files from the Z: drive
• Firmware update occasionally fails
• Mirror: FTP process very slow running on WS2008 IIS7 FTP v7.5
• Print: Printer feeds ~10 inches after a 2-key (should be 3 inches max)
• SGD: file.type adds double quotes at beginning and end of file data
• ZPL: ^JUA command sets inactivity timeout to incorrect default value
• ZPL: Add ZPL configuration section to 2-key report
• ZPL: printer does not use stored tear-off setting after power up
• ZPL: ^MF command fails to perform media calibration
• ZPL: printer delays 2-3 seconds when format contains a ^JUS
• 802.11: Fails to connect to an AP configured for WEP with shared authentication
• 802.11: Remote auto-connect occurring before power on mirror
File.dir_format SGD Command

A new SGD parameter called file.dir_format has been created. When set to “zpl” the file.dir command
operates as described in the ZPL programming manual. When set to “cpcl” the file.dir command operates
identically to the DIR command described in the CPCL programming manual. The default value is “zpl”.
Examples
! U1 setvar "file.dir_format" "cpcl"
! U1 getvar "file.dir_format"
! U1 getvar "file.dir"
62
V68.18.0Z
Enhancements
• Add support for ZPL (see comments below)
• Add support for ZPL command override feature (see comments below)
• Add support for XML input
• Add support for ZBI 2.0 (requires license to enable)
• Reduced printer shutdown time
• Mirror: Add support for fs_image feature
• Mirror: add support for ip.mirror.enable_firmware_update SGD
• SGD: Add support for remote auto-connect via TCP
• SGD: Add support for Secure FTP (SFTP)
• SGD: add capability to save a two-key report to a text file (see comments below)
• SGD: add support for ip.dhcp.cache_ip parameter
• SGD: add ability to restore all defaults (device.restore_defaults with “all” option)
• SGD: optional disablement of battery alerts
• SGD: add support for DHCP Option 12
• LCD: Envelop icon now stays on when the parser is locked to a port expecting more data
• Add ability to parse ZPL commands in config.sys and autoexec.bat files
Issues Corrected
• Telnet.wml file does not work
• Index.shtml and logo.png files show up in E: drive listing
• Bluetooth: Potential loss of data when a connection is closed by the host
• LCD can become garbled on power up
• LCD: display “Restarting” instead of “Shutting Down” after a firmware update
• Mirror: unable to FTP index.shtml file
• Mirror: files with more than 16.3 characters in the filename do not mirror
• Mirror: alert messages are not correct per the user manual
• Mirror: update incorrectly triggered by updating file on E: drive
• Mirror: fails when using a DNS server name
• Mirror: fs_image hangs in UNIX/LINUX environment
• Print: RSS expanded barcodes are difficult to scan
• SGD: The media.tof parameter is not persistent
• SGD: The media.tof parameter does not support negative values
• 802.11: Static IP addresses do not display on LCD (or SGD) until printer is associated
63
• 802.11: FTP login with –A option (anonymous) does not work from a Microsoft Windows platform (see
comments below)
ZPL Notes for QLn

• No changes are needed to the device.languages SGD parameter to enable ZPL, both CPCL and ZPL
are always active. Label formats using CPCL and ZPL commands can be alternated, but only on
complete label boundaries.
• ZPL labels print bottom first by default, as they do on legacy mobile printers and tabletop printers.
• Mobile batch files: ZPL commands are now supported in the config.sys and autoexec.bat files. For
example the ^POI command can be added to the config.sys file to cause labels to print top first.
• When printing ZPL labels the default drive is the R: drive. In other words if you load a file via a ZPL
command and the drive letter is not specified, the file will be stored on R:. All CPCL files are stored on
the E: drive.
• The concept of Pause is an inherent part of ZPL. There are several commands that will put the printer in
a Paused state. Tabletop printers address this by including a Pause button on the front panel. The QLn
does not have this option. When the QLn enters a Paused state, the Pause message will appear on the
screen. Pressing the Feed Button will take the printer out of Pause and will NOT feed any media. If the
printer is not in a Paused state, and the feed button is pressed, the normal label feed operation will be
performed.
• For printing on continuous media with ZPL, we recommend using the black mark sensor. In CPCL, that
is the default behavior so no additional steps are required. That is not the case for ZPL. To use the
black mark sensor with ZPL for continuous media, set the sensor to the black mark with the following
commands, and then send your normal label with continuous content (note that printer uses the sensor
to determine if it is out of media):
^xa^mnm^xz
^xa
^mnn
….Normal label content
^xz
• ZPL Fonts: All standard ZPL fonts are available. Custom fonts must be True type (.ttf) only, Intellifont
(.fnt) fonts are not supported. Swiss721 will be included on new printers from the factory, and is
available from Zebra Technical Support for printers sold prior to this release. Note that the ~DY
command must be used to download the font to the printer, see below regarding the ~DU command.
• The following ZPL features and commands are not present in this release, but may be added in a future
release:
• Real Time Clock functionality: labels with RTC content will not be re-rendered if the label doesn’t print
within the specified time. For example, this situation can arise if you send a label to the printer and the
printer is out of media.
• ÎF - change current working folder
• ^MA - Set Maintenance Alerts
• ^MP - Mode Protection
• ^MW - Modify Heading Warning
• ^NT - SMTP zpl command
64
• ^ZZ - Printer Sleep

• ~DU – Download Unbounded True Type Font
• ~HE - Returns to Host Eprom Status
• ~HU - Return ZebraNet Alert Configuration
• ~NR - Set All Network Printers Transparent
• ~NT - Set Currently Connected Printer Transparent
• The following ZPL commands are not present in this release due to deprecation of support for Intellifont
fonts:
• ~DS – Download Intellifont
• ~DT – Download Bounded True Type Font
• The following ZPL commands are not present in this release due to hardware incompatibilities:
• ^JV and ~JV - Clamping for the PAX
• ~PR - Applicator Reprint
• Avoiding ZPL calibration at startup: The QLn does not automatically perform ZPL calibration at startup
to avoid wasting media. In addition, the SGD command zpl.label_length can be used to avoid executing
the ~JC command for similar reasons (though ~JC is supported and can be used if desired). This
parameter allows the user to specify the length of the media being used in dot rows, presumably in a
startup batch file. This is the same command used on the QL Plus. The format of the command is as
follows (for a 400 dot row label in this example):
! U1 setvar "zpl.label_length" "400"
! U1 getvar "zpl.label_length"
• The zpl.label_length SGD parameter is updated to the length of the media being used if the ~JC
command is executed.
• TCP port: The QLn listens on both ports 6101 (traditional CPCL port) and 9100 (traditional ZPL port),
for both the Ethernet and 802.11 interfaces.
ZPL Override Command

A new suite of SGD parameters called device.override has been created. These are permanent settings
which indicate whether or not the specified ZPL commands are ignored. The intent is to include the
device.override commands in a start up file, to take effect on subsequent ZPL commands sent to the
printer via one of the communications interfaces. Only a small subset of ZPL commands can be
overridden, these are listed below. This feature is not supported for CPCL commands. The following
describes the specific SGD commands:
device.command_override.add: looks for a supported override command, and if supported adds it to
the override list. This is a setvar command only.
device.command_override.clear: clears the override list. This is a setvar command only.
device.command_override.list: returns the list of ZPL commands to override. This is a getvar
command only.
Supported ZPL commands that can be overridden: ^MN and ^MM
65
Examples
! U1 setvar "device.command _ override.add" "^MN"
! U1 setvar "device.command _ override.add" "^MM"
! U1 setvar "device.command _ override.clear" ""
! U1 getvar "device.command _ override.list"
Saving the 2-Key Report to a File

This feature is intended to facilitate interactions between the user and Zebra technical support. Often a
copy of the 2-key (configuration) report is required to debug a problem. Prior to this feature the 2-key
needed to be printed and scanned. With this feature the report can now be saved to a text file on the
printer’s flash memory, copied to a local PC using the Zebra Setup Utility (ZSU), and then emailed. To
generate the report send the following command to the printer using the “Open Communication With
Printer” menu in the ZSU:
! U1 do "device.save _ 2key" "now"

To retrieve the file send the following command:
! U1 do "file.type" "2key.txt"
This will display the results in the receive window. On the File menu of the ZSU, select Export Received
Data, and save to a file on your PC.
Using Anonymous FTP Login from a Microsoft Windows Platform

A new SGD parameter (ip.ftp.request_password) has been added to control whether the password was
requested by the ftp client. In order to make the QLn behave the same way as the legacy QL Plus family
did when sending an ftp –A command from a Microsoft Windows platform, first send the following
command to the printer:
! U1 setvar "ip.ftp.request_password" "yes"

Note that the default behavior for QLn is similar to Zebra desktop and tabletop printers (i.e., the default
value for the above SGD is “no”).
V68.16.3Z
Enhancements
• 802.11: Added wlan.roam.interval parameter, reduces roaming
• 802.11: Improved roaming algorithm
Issues Corrected
• HW: Incorrect media width sensor operation
• HW: Enable charging circuit on power up
• COMM: Serial and USB port lockup after 1020 labels on QLn220 only
• CPCL: QLn responding incorrectly in CPCL synchronous mode
• CPCL: After media load PRESENT-AT is not performed
66
• CPCL: Print redirection not working when run from a startup file
• Ethernet: DHCP fails on soft reset when docked
• 802.11: Application corruption when mirroring
• 802.11: WEP-128 requires all four keys to be set, should only need one
• 802.11: IP roam packets not sent if WEP-128 is used
• 802.11: Roaming thresholds using incorrect values, see note below
• 802.11: Updated roaming related default values, see note below
• 802.11: “Loss of Signal” alert messages are too aggressive
• 802.11: In range roaming based on signal strength does not work
• WML: Unable to display full Latin character set using custom WML files
After loading this release it is necessary to send the following commands to the printer in order to update
the default roaming values:
! U1 do "device.restore _ defaults" "wlan"

! U1 do "device.reset" ""
Note that a carriage return and line feed are required after each line.
V68.16.2ZA
67
(Service Pack)
Enhancements
• N/A
Issues Corrected
• HW: incorrect media width sensor operation
• COMM: Serial and USB port lockup after 1020 labels on QLn220 only
• CPCL: QLn responding incorrectly in CPCL synchronous mode
V68.16.2Z
Enhancements
N/A
Issues Corrected
• PRINT: Feed key does not perform PRESENT-AT
• CPCL: TYPE command does not respond when file does not exist
• 802.11: Roaming does not work when using WEP encryption
• 802.11: IP roam packets sent out before DHCP request
• 802.11: Channels mask does not work for channels 12 – 14
V68.16.1ZA
68
(Service Pack)
Release Date: 15 July 2011
Enhancements
• N/A
Issues Corrected
• PRINT: Feed key does not perform PRESENT-AT
• CPCL: TYPE command does not respond when file does not exist
• 802.11: Roaming does not work when using WEP encryption
• 802.11: IP roam packets sent out before DHCP request
V68.16.1Z
Enhancements
Original release on QLn220
Issues Corrected
• PRINT: Improved print quality on tag stock.
V68.16.0Z
Release Date: 06 May 2011
This is the initial release of this firmware. It is for use with the following printer models:
• QLn320
69
V72 Printer OS
Release Notes
Link-OS 5 ............................................................................................................................................................70
V72.20.10Z .................................................................................................................................................70
Link-OS 4 ............................................................................................................................................................73
V72.20.01ZB ...............................................................................................................................................73
V72.20.01Z .................................................................................................................................................73
Link-OS 3 ............................................................................................................................................................78
V72.19.15Z ..................................................................................................................................................78
V72.19.13Z ..................................................................................................................................................78
V72.19.10Z ..................................................................................................................................................79
Link-OS 2 ............................................................................................................................................................81
V72.19.6Z ....................................................................................................................................................81
Link-OS 1 ............................................................................................................................................................83
V72.19.5Z ....................................................................................................................................................83
V72.19.1Z ....................................................................................................................................................83
Non-Link-OS .......................................................................................................................................................84
V72.18.4Z ....................................................................................................................................................84
V72.18.3Z ....................................................................................................................................................84
V72.18.2ZA ..................................................................................................................................................85
V72.18.2Z ....................................................................................................................................................86
Link-OS 5
V72.20.10Z
• ZT210
• ZT220
• ZT230
Changes
details):
70

• OpenSLL v1.0.21
• The SYSLOG now supports an entry for power down/reset.
details):
• device.location
• has been added.
Issue Corrected
71
• The display of “Labels remaining in batch” information on the front panel has been optimized.
"media.tof_tune"
media.tof_adjust.
• Example:
" print.vertical_dpi_adjust "

• Range: 95.0 to 105.0.
• Example:
! U1 setvar "device.cpcl_adjust_length_dpi" "97.8"
72
Link-OS 4
V72.20.01ZB
• ZT210
• ZT220
• ZT230
Issues Corrected
V72.20.01Z
• ZT210
• ZT220
• ZT230
Changes
73
Default Value: "on"

Service):
Discovery Data
transmitted:
Printer Settings
74

Printer Settings
media.type
ezpl.media_type
each command.
75
Issues Corrected
instead.
button is pressed.
avoid conflicts.
enum type.
76

77
Link-OS 3
V72.19.15Z
• ZT210
• ZT220
• ZT230
Changes
Issues Corrected
V72.19.13Z
• ZT210
• ZT220
• ZT230
Changes
• The printers now support the “small label tracking” feature, by default. The command
"media.small_label_tracking" can be set to "off" to disable this feature.
• Front Panel passwords are now supported on the ZT230. The password level can be set from the Tools
menu.
78
Issues Corrected
• The printer will no longer apply adjustments to the ~TA (Tear Off) setting after completing the “No
Motion” Head Open or Power Up action.
• The contrast setting on the display will be retained through a power cycle.
enhanced.
• ZBI program throughput has been enhanced.
"off").
V72.19.10Z
• ZT210
• ZT220
• ZT230
Changes
now supported.
79
• The total label count odometer value has been added to the configuration label.
each other.
Issues Corrected
• Throughput for small labels (1.5" long and shorter) has been enhanced.
logic board has been installed.
• The Czech and Russian translations on the front panel of the ZT230 have been updated.
• The ZT230 front panel menu now supports a Label Top setting.
• The printer web page label preview function has been enhanced to support longer labels.
• Keyboard Display Unit support has been enhanced to correctly support processing Real Time Clock
fields.
• Sensor selections (Reflective/Transmissive) will now be maintained through a power cycle.
• EPL cut mode processing has been enhanced to better handle repeated cut events in a batch.
80
Link-OS 2
V72.19.6Z
This firmware includes all features of the previous V72.19.5Z, and is for use with the following printer
models:
• ZT210
• ZT220
• ZT230
NOTE: For optimal printing quality and proper printer performance across our product line, Zebra strongly
recommends the use of genuine Zebra supplies as part of the total solution. Specifically, the ZT210,
ZT220, and ZT230 printers are designed to work only with genuine Zebra printheads, thus maximizing
safety and print quality. Please note the following Printer status messages that can be displayed on the
unit.
Table 2
Status of Printer as Shown by STATUS light steady red
Indicator Lights:
PAUSE light steady red
DATA light steady red
The printhead was replaced with one that is not a genuine

ZT230 Error Message: Zebra printhead. Install a genuine Zebra printhead to
PH NOT AUTHENTICATED
continue.
REPLACE PRINTHEAD
Changes
• The Link-OS version number is now 2.0
• In order to ensure current time reporting, the Real-time clock has been enhanced to support
re-rendering formats during printing.
"on".
The package of Cloud Connect/weblink information sent from the DHCP server in the Option 43
• Server address
81

The package of Mirror information sent from the DHCP server in the Option 43 packet can include the:
• Server address
• Mirror path
• Mirror mode
• Added a "default" field to the "allconfig" JSON response for each setting
• The Cloud Connect weblink connection now logs the servers certificate serial number and fingerprint
• Additional bits added to the ~HQES response and Advanced Discovery packet
• A new setting weblink.ip.connX.num_connections has been added. This setting shows the number
of established connections. The control channel counts as 1 as well as all other sub channels (echo,
new settings are:
device.position.latitude in degrees min/max: -90.0/90.0
device.position.longitude in degrees man/max: -180.0/180.0
device.position.altitude in meters min/max: -10000.0/406700000.0
device.position.accuracy in meters min/max: 0.0/406700000
• User available E: memory is now 32MB.
Issues Corrected
• .TTF and .TTE files will now be listed when using the "List Fonts" from the front panel.
• ZBI Event ID 4 (Cancel Key press) is now supported.
• Settings will now appear correctly in the ZebraNet Bridge application.
• Handing DSR handshaking has been altered to duplicate the behavior used on the S4M.
• Downloading larger font files has been improved.
82
Link-OS 1
V72.19.5Z
This firmware includes all features of the previous V72.19.1Z, and is for use with the following printer
models:
• ZT210, ZT220, ZT230
Changes
• Dual support for ZPL and EPL II
NOTE: The following commands are not supported:

AUTOFR, fB, JB, JC, JF, OF, OS, US, US1, UT.
When using the tap to reprint function on the ZT230, the printer must be at the idle screen and the down
arrow key is used to trigger the reprint event.
• The SGD command "device.epl_legacy_mode" now supports a new "2746e" parameter. This
mode is the default setting on ZT200 series printers.
NOTE: You must send the following two commands to get all of the 2746e compatibility features:
! U1 setvar "device.epl_legacy_mode" "2746e"
! U1 setvar "device.epl_legacy_mode" "print_orientation"
• The SGD command "device.languages" now supports "zpl", "hybrid_xml_zpl", "epl" and
"epl_zpl". The default on ZT200 series printers is now "epl_zpl".
• The ^MWN command will now deactivate the HEAD COLD Warning.
Issues Corrected
• The default Telnet password has been set to "1234"
• ^MWN command is now working correctly.
V72.19.1Z
• ZT210
• ZT220
• ZT230
This firmware includes all features of the previous Non-Link-OS.
Issues Corrected
NA
83
Link-OS Features
Initial release of Link-OS support.
• Data Capture to SGD
• Unsolicited alerts for SGD changes
• HTTP POST transport for unsolicited alerts
• SGD change log
• ZBI events for SGD changes
• User Variables Port 9200 -- SGD Channel
• Cloud Connectivity
Non-Link-OS
V72.18.4Z
• ZT210
• ZT220
• ZT230
Changes
• Improved 802.11n noise floor performance.
Issues Corrected
• Files sent from ZBI-Developer will now remain in flash after a power cycle.
V72.18.3Z
• ZT210
• ZT220
• ZT230

This firmware includes all features of the previous V72.18.2ZA
Changes
• The front panel menu system for the ZT230 now supports Japanese, Korean, Simplified Chinese and
Traditional Chinese, Russian, Polish, Czech and Romanian
84
• Front Panel Alerts on the ZT230 are now easier to read due to a new, larger character size font.
• A new Auto-Recovery feature has been added that will reinstall the printers operating system if an issue
is detected during printer start up. The operating system version on the printer will remain the same
after Auto-Recovery. When Auto-Recovery runs on a ZT230 printer, the unit will display
“Decompressing Files”, then “Writing Files to Flash” and then “Finishing Install” after which
the printer will then restart. When Auto-Recovery runs on a ZT210 or ZT220 printer, all LEDs will
remain yellow until the Auto-Recovery process is complete and then the printer will then restart.
NOTE: Data sent to the unit during a printer Operating System update or an Auto-Recovery may not be
received or processed.
Issues Corrected:
• The result of using the font identifier command (^CW) is now shown on the printers directory Web page.
• The Real-Time clock has been enhanced to roll-over to a new date when the month has 31 days and
“months” is being used as the offset time.
• The format counter response in the ~HS command response has been corrected when Reprint Mode is
enabled.
• The LPR port is now supported in ZBI apps.
• Processing of the ~JP command, when used with the Set-Get-Do command
• "formats.cancel_all" has been enhanced
• Web pages have been enhanced to display faster.
• Front Panel French phrases on the ZT230 have been edited to fit across the width of the screen
V72.18.2ZA
• ZT210
• ZT220
• ZT230
Changes
• None.
Issues Corrected
• When setting the printer password using the ^KP command, the web page password is also now set to
the same value.
• When Reprint Mode is enabled, using the ~PR command now reprints the last label printed.
• Sending the ^JZ command now re-prints the missing label after an error condition.
• The Label Take Up (LTU) unit will now rewind the backing before the printed label is removed.
• Persistent files can now only be deleted via the ÎD and file.delete commands when the file location and
file name are fully defined in the command.
85
V72.18.2Z
• ZT210
• ZT220
• ZT230
Changes
• 802.11a/b/g/n is now supported.
The front panel content is now entirely written in WML. Changes made to settings via the front panel are
now immediately in effect. For users who wish to edit the front panel content, the WML for the front panel is
available for download at zebra.com.
• The printer now supports a SNMP MIB. This is available for download at zebra.com. The “683” Print
Server MIB is no longer supported in this product.
• The printer now supports TCP Raw connections via ports 9100 and 6101 by default.
• The printer now supports up to 23 alerts.
• The Unicode engine can be turned off by sending ^XA^ZC2^XZ to the printer. It can be turned on by
sending ^XA^ZC0^XZ. Include a ^JUS before the ^XZ to make changes permanent across power cycles.
• The Swiss721 font is now included by default. If desired it can be deleted to recover space by sending
^XAÎDE:TT0003M_.TTF^XZ to the printer.
• Intellifont fonts are no longer supported. The ~DS and the ~DT commands are no longer supported.
• Scripts that previously called for font files named using the .fnt extension will now be supported by
the printer automatically searching on E memory for a .TTF file named with the same name. For
example, the printer will treat TT0003M_.TTF as if it were TT0003M_.FNT.
• The “Cold Start” Alert is now manageable. It is on by default, but can be deleted if desired. The alert
can be deleted via the web interface, or by sending ^SX0,F,N,N to the printer.
• If a getvar is executed against a branch name rather than a full SGD name, the printer will return the
name of all SGDs in that branch along with their possible values.
! U1 getvar “power” will return:

power.
power.dtr_power_off : on , Choices: on,off
power.shutdown
• A number of new Set-Get-Do commands are supported. These are listed here and detailed in the
Programming Guide:
• comm.halt • netmanage.avalanche.agent_addr
• comm.handshake • netmanage.avalanche.available_agen
t
• device.cutter_installed • netmanage.avalanche.available_port
• device.ff_disable • netmanage.avalanche.encryption_typ
e
86
• device.host_identification • netmanage.avalanche.interval
• device.host_status • netmanage.avalanche.interval_update
• device.ltu_installed • netmanage.avalanche.model_name
• device.pause • netmanage.avalanche.set_property
• device.print_reprogram_2key • netmanage.avalanche.startup_update
• device.super_host_status • netmanage.avalanche.tcp_connection
_timeout
• device.unpause • netmanage.avalanche.terminal_id
• display.backlight • netmanage.avalanche.text_msg.
• display.backlight_on_time • netmanage.avalanche.text_msg.beep
• display.language • netmanage.avalanche.text_msg.displ
ay
• display.load_card • netmanage.avalanche.text_msg.print
• ezpl.head_close_action • netmanage.avalanche.udp_timeout
• ezpl.label_length_max • parallel_port.mode
• ezpl.label_sensor • parallel_port.present
• ezpl.manual_calibration • power.dtr_power_off
• ezpl.media_type • power.label_queue.
• ezpl.power_up_action • power.label_queue.shutdown
• ezpl.print_method • power.shutdown
• ezpl.print_mode • sensor.paper_supply
• ezpl.print_width • sensor.peeler
• ezpl.reprint_mode • usb.connected
• ezpl.take_label • usb.device.device_id_string
• ezpl.tear_off • usb.device.device_unique_id
• file.dir_format • usb.device.device_version
• formats.cancel_all • usb.device.manufacturer_string
• input.capture • usb.device.product_id
• interface.network.active.arp_interval • usb.device.product_string
• interface.network.active.cable_type • usb.device.serial_string
• interface.network.active.cache_ip • usb.device.vendor_id
• interface.network.active.dhcp_received_ho • usb.halt
st_name
• interface.network.active.protocol_error • wlan.11n.20mhz_only
• interface.network.active.rx_errors • wlan.11n.aggregation
• interface.network.active.rx_packets • wlan.11n.greenfield
• interface.network.active.server_address • wlan.11n.rifs
• interface.network.active.server_protocol • wlan.11n.short_gi_20mhz
• interface.network.active.speed • wlan.11n.short_gi_40mhz
• interface.network.active.tx_errors • wlan.active_channels
87
• interface.network.active.tx_packets • wlan.allowed_band
• interface.network.active.wins_addr • wlan.channel_mask
• internal_wired.ip.dhcp.arp_verify • wlan.ip.dhcp.arp_verify
• internal_wired.ip.port_alternate • wlan.ip.port_alternate
• ip.dhcp.arp_verify • wlan.permitted_channels
• ip.dhcp.user_class_id • wlan.roam.monitor
• ip.dhcp.vendor_class_id • wlan.user_channel_list
• ip.ftp.request_password • wlan.waveagent.
• ip.http.admin_name • wlan.waveagent.enable
• ip.http.admin_password • wlan.waveagent.udp_port
• ip.http.custom_link_name • zpl.calibrate
• ip.http.custom_link_url • zpl.caret
• ip.http.faq_url • zpl.control_character
• ip.http.port • zpl.delimiter
• ip.mirror.mode • zpl.label_length
• ip.port_alternate • zpl.left_position
• ip.snmp.trap_community_name • zpl.save
• log.reboot. • zpl.system_error
• log.reboot.code • zpl.system_status
• log.reboot.codes • zpl.zpl_mode
• log.reboot.reason • zpl.zpl_override
• log.reboot.report
• The printer will negotiate with any parallel port connected print server to determine which
communication methods can be supported (unidirectional “Compatibility Mode” or bi-directional “Nibble
Mode”). This applies to any parallel port connected print server.
• The ZebraLink 1284.4 layer is no longer supported. The IP address of a ZebraLink print server
connected to the parallel port will not be displayed on the printers front panel. Settings from a ZebraLink
Print Server connected to the printers parallel port will not be communicated between the print server
and printer.
• External wired SGD commands are not supported.
• The following items will be supported in a future release:
• Logical ports on the print server
• Japanese, Simplified Chinese, Traditional Chinese, Russian, Polish, Romanian, Czech, and Korean
translations on the front panel
• Real Time Clock
• ^MP full implementation (button protection is supported)
• Front panel passwords
88
V73 Printer OS
Release Notes
Link-OS 5 ............................................................................................................................................................89
V73.20.10Z .................................................................................................................................................89
Link-OS 4 ............................................................................................................................................................92
V73.20.01ZB ...............................................................................................................................................92
V73.20.01Z .................................................................................................................................................93
Link-OS 3 ............................................................................................................................................................97
V73.19.15Z ..................................................................................................................................................97
V73.19.13Z ..................................................................................................................................................97
V73.19.10Z ..................................................................................................................................................98
V73.19.7Z ....................................................................................................................................................99
Link-OS 2 ..........................................................................................................................................................101
V73.19.6Z ..................................................................................................................................................101
Link-OS 5
V73.20.10Z
• iMZ220
• iMZ320
Changes
details):
89

• OpenSLL v1.0.21
details):
modes as follows:
access.
90


print (default) Display Only If Passkey Pairing is used, the printer will print out a
small label with the passkey to be entered on the
remote device.
If LE Numeric Comparison is used, the printer will print
out the passkey and will auto-confirm the pairing
request.
noprint Display Only If Passkey Pairing is used, the printer will not print out
the passkey.
If LE Numeric Comparison is used, the printer will not
print out the passkey, but will auto-confirm the pairing
request.
off No I/O Passkey pairing is not allowed. Only “Just Works”
pairing can be used, and MITM protection is not
possible. It is not possible to reject the pairing request!
Issue Corrected
disconnects.
"media.tof_tune"
media.tof_adjust.
91
• Example:
• Range: 95.0 to 105.0.
• Example:
Link-OS 4
V73.20.01ZB
• iMZ220
• iMZ320
Issues Corrected
92
V73.20.01Z
• iMZ220
• iMZ320
Changes
Default Value: "on"

Service):
93
Discovery Data
transmitted:
Printer Settings
94

Printer Settings
media.type
ezpl.media_type
each command.
95
Issues Corrected
instead.
button is pressed.
avoid conflicts.
enum type.
96
Link-OS 3
V73.19.15Z
• iMZ220
• iMZ320
Changes
Issues Corrected
V73.19.13Z
• iMZ220
• iMZ320
Changes
• The new Zebra logo is now used on the web pages and two-key report.
Issues Corrected
97
enhanced.
• The ^GFA command will no longer produce a stretched image when the last line of the encoded graphic
is a “,” or a “!”.
of more devices.
• The USB implementation has been enhanced to optimize bi-directional communication. .
"off").
• The sensor system will now turn off when not printing, to optimize battery use.
Multiplatform SDK.
V73.19.10Z
• iMZ220
• iMZ320
Changes
now supported.
• "Qatar" is now a supported value for the "wlan.country_code" SetGetDo command.
98

each other.
• The "power.low_battery_warning_raw" command now uses use a consistent implementation across
the Link-OS Mobile product line. If updating an existing printer, users will have to send the
! U1 setvar "device.restore_defaults" "power"
command to use this new implementation.
Issues Corrected
• The printer will now respond to an "Escape H" command, when it’s received at the end of a ZPL format.
request.
• Media sensing calibration has been enhanced to increase accuracy.
• Media cover open (print head open) detection has been improved.
V73.19.7Z
• iMZ220
• iMZ320
99
This firmware includes all the features of the previous V73.19.6Z release.
Changes
None
Issues Corrected
• Bluetooth® connection handling has been improved.
• Handling of repeated bi-directional data requests over Bluetooth has been improved.
• Handling of large (over 600 byte) data streams over Bluetooth have been improved.
• The device.macro_get command has been enhanced to handle pre- and post- pending.
• Improved the radio start up process to ensure correct MAC address reporting.
100
Link-OS 2
V73.19.6Z
• iMZ220
• iMZ320
This firmware includes all the features of the previous V73.19.2Z release.
Changes
• The Link-OS version number is now 2.0.
• Added support for simultaneous 802.11 a/b/g/n and Bluetooth® Dual Radio.
NOTE: The Dual radio option is only available on the n radio configuration. By default, the Bluetooth radio
is disabled on printers that support dual radio. The Bluetooth radio can be enabled by using the
bluetooth.enable command. When both the WLAN and Bluetooth radios are enabled, the
wlan.power_save feature will be turned off.
"on".
• The package of Cloud Connect/weblink information sent from the DHCP server in the Option 43
• Server address
• The package of Mirror information sent from the DHCP server in the Option 43 packet can include the:
• Server address
• Mirror path
• Mirror mode
• Added a "default" field to the "allconfig" JSON response for each setting.
• The Cloud Connect weblink connection now logs the servers certificate serial number and fingerprint.
• Additional bits added to the ~HQES response and Advanced Discovery packet.
101
• A new setting weblink.ip.connX.num_connections has been added. This setting shows the number of
established connections. The control channel counts as 1 as well as all other sub channels (echo,
new settings are:
• device.position.latitude in degrees min/max: -90.0/90.0
• device.position.longitude in degrees man/max: -180.0/180.0
• device.position.altitude in meters min/max: -10000.0/406700000.0
• device.position.accuracy in meters min/max: 0.0/406700000
• This release includes support for simultaneous 802.11 a/b/g/n and Bluetooth® operation on units that
have both radios.
• User available E: memory is now 16MB.
Issues Corrected
• PCX graphics handling has been improved to handle additional scenarios.
• Handling of Bluetooth remote device disconnect events improved.
• odometer.user_label_count can be set to "0".
102
V74 Printer OS
Release Notes
Link-OS 5 ..........................................................................................................................................................103
V74.20.10Z ...............................................................................................................................................103
Link-OS 4 ..........................................................................................................................................................107
V74.20.01ZB .............................................................................................................................................107
V74.20.01Z ...............................................................................................................................................107
Link-OS 3 ..........................................................................................................................................................112
V74.19.15Z ................................................................................................................................................112
V74.19.13Z ................................................................................................................................................112
V74.19.10Z ................................................................................................................................................113
V74.19.9Z ..................................................................................................................................................115
V74.19.7Z ..................................................................................................................................................116
Link-OS 2 ..........................................................................................................................................................116
V74.19.6Z ..................................................................................................................................................116
Link-OS 5
V74.20.10Z
• ZD500
• ZD500R
Changes
details):
103
• OpenSLL v1.0.21
details):
modes as follows:
access.
104


remote device.
request.
the passkey.
request.
Issue Corrected
• Larger RFID label (5.5” wide by 16” long) will now print without blank labels.
disconnects.
• When printing small labels, the labels that print after a RFID VOID label no longer have a faint “VOID”
printed on them.
105
"media.tof_tune"
media.tof_adjust.
• Example:
• Range: 95.0 to 105.0.
• Example:
106
Link-OS 4
V74.20.01ZB
• ZD500
• ZD500R
Issues Corrected
V74.20.01Z
• ZD500
• ZD500R
Changes
• The Visibility Agent can be turned off via the printer’s web pages or front panel. See the Application
Note “Opting Out of the Asset Visibility Agent” included with this firmware download and posted on
zebra.com.
107
Default Value: "on"

Service):
Discovery Data
transmitted:
Printer Settings
108

Printer Settings
media.type
ezpl.media_type
• MEDIA AUTO-DETECT is now supported on the ZD500.
each command.
109
• After an RFID Void label is printed, the printer will print using the configured print speed and darkness.
• Monza 6 tags are now supported.
Issues Corrected
• The printer will report error code 81 during a paper jam in response to the EPL command êe.
instead.
avoid conflicts.
enum type.
• The German translations in the RFID menu have been corrected.
110

• The first label printed after a RFID VOID will no longer use lower-than-configured darkness.
• MEDIA OUT detection in black mark mode has been optimized.
• The Tear-Off adjust command setting will be used after a power cycle if Media Power Up is set to No
Motion.
111
Link-OS 3
V74.19.15Z
• ZD500
• ZD500R
Changes
Issues Corrected
V74.19.13Z
• ZD500
• ZD500R
Changes
• Link-OS printers’ now support downloading PEM and DER formatted WLAN certificates in the P12
“Direct WLAN Cert Downloading”.
• Front Panel passwords are now supported. The password level can be set from the Tools menu.
• The new Zebra logo is now used on the front panel and web pages.
Issues Corrected
• RFID tag calibration has been enhanced to increase first tag tracking accuracy.
• No Motion calibration has been enhanced when short labels are used.
112
enhanced.
is a “,” or a “!”.
of more devices.
"off").
V74.19.10Z
• ZD500
• ZD500R
Changes
now supported.
each other.
113

• Monza 4, 5 and 6 tags are now supported.
Issues Corrected
• The Czech and Russian translations on the front panel have been updated.
request.
fields.
• The RFID antenna setting will now be saved after an RFID calibration.
114
V74.19.9Z
This firmware release includes the features of the previous V74.19.7Z release. It is for use with the
following ZPL printer models:
• ZD500
• ZD500R
Changes
• Support for additional countries added to the rfid.country_code command.
Issues Corrected
• MAC address configuration optimized to reduce potential for duplicate address reporting.
• RFID tag encoding enhanced to improved accuracy.
115
V74.19.7Z
This firmware release includes the features of the previous V74.19.6Z release. It is for use with the
following ZPL printer models:
• ZD500
• ZD500R
Changes
• Added support for the ZD500 printer.
• Backlight timeout menu control added to the ZD500 and ZD500R.
• Backlight timeout default changed to 600 seconds (10 minutes).
• RFID Menu on the non-RFID ZD500 unit displays:
RFID AVAILABLE ON ZD500R.
• Support for additional countries added to the wlan.country_code and rfid.country_code commands.
Issues Corrected
None.
Link-OS 2
V74.19.6Z
This is the initial firmware release for the ZD500R.
116
V75 Printer OS
Release Notes
Link-OS 5 ..........................................................................................................................................................117
V75.20.10Z ...............................................................................................................................................117
Link-OS 4 ..........................................................................................................................................................121
V75.20.01ZB .............................................................................................................................................121
V75.20.01Z ...............................................................................................................................................121
Link-OS 3 ..........................................................................................................................................................126
V75.19.15Z ................................................................................................................................................126
V75.19.13Z ................................................................................................................................................126
V75.19.10Z ................................................................................................................................................127
V75.19.7Z ..................................................................................................................................................128
Link-OS 5
V75.20.10Z
• ZT410 (203, 300, and 600 dpi)
• ZT420 (203 and 300 dpi)
Changes
details):
117

• OpenSLL v1.0.21
details):
modes as follows:
access.
118



passkey.

Issue Corrected
disconnects.
printed on them.
119
"media.tof_tune"
media.tof_adjust.
• Example:

• Range: 95.0 to 105.0.
• Example:
120
Link-OS 4
V75.20.01ZB
• ZT410 (203, 300, and 600 dpi)
• ZT420 (203 and 300 dpi)
Issues Corrected
V75.20.01Z
• ZT410 (203, 300, and 600 dpi)
• ZT420 (203 and 300 dpi)
Changes
zebra.com.
121
Default Value: "on"

Service):
Discovery Data
transmitted:
Printer Settings
122

Printer Settings
media.type
ezpl.media_type
each command.
123
• After an RFID Void label is printed, the printer will print using the configured print speed and darkness.
• Monza 6 tags are now supported.
Issues Corrected
• Small label tracking has been optimized so that the label correctly feeds to the next edge when
pressing the FEED button after printing a label in rewind mode.
• The PRINT INFO output on the 600 dpi unit now prints at the correct size.
instead.
avoid conflicts.
124

enum type.
• The German translations in the RFID menu have been corrected.
• MEDIA OUT detection in black mark mode has been optimized.
Motion.
• Black mark media sensing has been optimized to enhance calibration.
• The Rewind spindle will continue to operate if the printer is in PEEL mode and a label is left in the
Presenter.
• Forced download will now operate when the Parallel port card is installed.
125
Link-OS 3
V75.19.15Z
• ZT410 (203, 300, and 600 dpi)
• ZT420 (203 and 300 dpi)
Changes
Issues Corrected
V75.19.13Z
• ZT410 (203, 300, and 600 dpi)
• ZT420 (203 and 300 dpi)
Changes
• Link-OS printers’ now support downloading PEM and DER formatted WLAN certificates in the P12
• Front Panel passwords are now supported. The password level can be set from the Tools menu.
Issues Corrected
• The printers now support the “small label tracking” feature, by default. The command
“media.small_label_tracking" can be set to "off" to disable this feature.
enhanced.
126
• The "netmanage.avalanche.agent_addr" command will now accept a DNS. value.

is a “,” or a “!”.
of more devices.
"off").
• Handling of the inter-label gap has been modified so that label image length more accurately matches
that of the ZT2xx and ZM4xx models.
V75.19.10Z
• ZT410 (203, 300, and 600 dpi)
• ZT420 (203 and 300 dpi)
Changes
now supported.
127
each other.
• Monza 4, 5 and 6 tags are now supported.
Issues Corrected
• The Czech and Russian translations on the front panel have been updated.
request.
fields.
• The RFID antenna setting will now be saved after an RFID calibration.
• USB Mirror events will not run at the same time as IP based Mirror events.
• EPL cut mode processing has been enhanced to better handle repeated cut events in a batch.
V75.19.7Z
This firmware release is for use on the following printers:
128
• ZT410 (203, 300, and 600 dpi)

• ZT420 (203 and 300 dpi)
Changes
This is the initial release for this platform, with these features:
• Dual support for ZPL II® and EPL2.
• Support for the Profile Manager app, using Cloud Connect.
• Support for the Print Touch app.
• On-screen QR Codes that can be displayed on the printer’s LCD during Warning and Error events.
• USB Mirror (automated printer management via USB). DOS Fat 32 formatted memory stick with the
Mirror directory structure required. See the USB Mirror documentation for details.
• Ability to use a USB Human Interface device type (a keyboard or scanner) to fill templates stored on the
printer, via the on-printer Print Station app.
• Ability to transfer selected file types from a USB memory stick to the printer. DOS Fat 32 formatted
memory stick required.
• Ability to transfer selected file types from the printer to a USB memory stick. DOS Fat 32 formatted
memory stick required.
• New SetGetDo commands have been created; consult the Programming Guide for details.
• Real time clock.
• RFID-Ready.
• System event logging.
129
V76 Printer OS
Release Notes
Link-OS 5 ..........................................................................................................................................................130
V76.20.10Z ...............................................................................................................................................130
Link-OS 4 ..........................................................................................................................................................134
V76.20.01ZB .............................................................................................................................................134
V76.20.01Z ...............................................................................................................................................134
Link-OS 3 ..........................................................................................................................................................139
V76.19.15ZA ..............................................................................................................................................139
V76.19.15Z ................................................................................................................................................139
V76.19.13Z ................................................................................................................................................140
V76.19.10Z ................................................................................................................................................141
Link-OS 5
V76.20.10Z
• ZQ510
• ZQ520
Changes
details):
130

• OpenSLL v1.0.21
products:

details):
• device.location
• has been added.
modes as follows:
access.
131


remote device.
request.
the passkey.
request.

Value
132
Issues Corrected
disconnects.
"media.tof_tune"
media.tof_adjust.
• Example:

• Range: 95.0 to 105.0.
• Example:
! U1 setvar "print.vertical_dpi_adjust " "97.8"
133
Link-OS 4
V76.20.01ZB
• ZQ510
• ZQ520
Issues Corrected
V76.20.01Z
This firmware includes all features of the previous V76.19.15ZA release, except where noted otherwise. It
is for use with the following printer models:
• ZQ510
• ZQ520
Changes
134
Default Value: "on"

Service):
Discovery Data
transmitted:
Printer Settings
135

Printer Settings
media.type
ezpl.media_type
each command.
136
Issues Corrected
• The default for the command device.alerts.audible is now “high.”
• The printer will now attempt to reconnect to the WLAN connection when removed from the powered
cradle while in sleep mode.
instead.
button is pressed.
avoid conflicts.
enum type.
• The printer will now communicate via the USB port when powered by the Battery Eliminator.
137
138
Link-OS 3
V76.19.15ZA
• ZQ510
• ZQ520
Changes
• None
Issues Corrected
• The USB On-The-Go port will now be enabled when the printer is connected to the Battery Eliminator.
• The printer will now attempt to reconnect to the WLAN connection when removed from the powered
cradle while in sleep mode.
button is pressed.
V76.19.15Z
• ZQ510
• ZQ520
Changes
Issues Corrected
139
V76.19.13Z
• ZQ510
• ZQ520
Changes
• The Battery Eliminator Cradle is now supported.
• The USB/Serial cable is now supported.
Issues Corrected
• Print Quality for content that is printed immediately after a full width solid line has been improved.
• The OID: .1.3.6.1.4.1.10642.200.14.5.0 (zql-power-low-battery_shutdown) response has been
corrected.
enhanced.
of more devices.
• The printer will now wait to complete an on-going Bluetooth connection attempt when the sleep timeout
is reached.
140

"off").
Multiplatform SDK.
• The printer will now stay on when the power.inactivity_timeout is set to a non-zero value and the unit is
plugged in or in a powered cradle.
V76.19.10Z
This is the initial release for this platform.
141
V78 Printer OS
Release Notes
Link-OS 5 ..........................................................................................................................................................142
V78.20.10Z ...............................................................................................................................................142
Link-OS 4 ..........................................................................................................................................................146
V78.20.01ZB .............................................................................................................................................146
V78.20.01Z ................................................................................................................................................146
Link-OS 3 ..........................................................................................................................................................150
V78.19.15Z ................................................................................................................................................150
V78.19.12Z ................................................................................................................................................150
Link-OS 5
V78.20.10Z
• ZR338
Changes
details):
142

• OpenSLL v1.0.21
details):
• device.location
• has been added.
modes as follows:
access.
143


remote device.
request.
the passkey.
request.
Issues Corrected
disconnects.
"media.tof_tune"
media.tof_adjust.
144
• Example:

• Range: 95.0 to 105.0.
• Example:
145
Link-OS 4
V78.20.01ZB
• ZR338
Issues Corrected
V78.20.01Z
This firmware includes all features of the previous Link-OS 3 release, except where noted otherwise. It is
• ZR338
Changes
146
Default Value: "on"

Service):
Discovery Data
transmitted:
Printer Settings
147

Printer Settings
media.type
ezpl.media_type
each command.
148
Issues Corrected
instead.
button is pressed.
avoid conflicts.
enum type.
149
Link-OS 3
V78.19.15Z
• ZR338
Changes
Issues Corrected
V78.19.12Z
• ZR338
Changes/Issues Corrected
None.
150
V79 Printer OS
Release Notes
Link-OS 5
Link-OS 5 ..........................................................................................................................................................151
V79.20.10Z ...............................................................................................................................................151
Link-OS 4 ..........................................................................................................................................................155
V79.20.01ZB .............................................................................................................................................155
V79.20.01Z ................................................................................................................................................155
Link-OS 3 ..........................................................................................................................................................160
V79.19.15Z ................................................................................................................................................160
V79.19.12Z ................................................................................................................................................160
V79.20.10Z
• ZR628
• ZR638
Changes
details):
151

• OpenSLL v1.0.21
details):
• device.location
• has been added.
modes as follows:
access.
152


remote device.
request.
the passkey.
request.
Issue Corrected
disconnects.
"media.tof_tune"
media.tof_adjust.
153
• Example:

• Range: 95.0 to 105.0.
• Example:
154
Link-OS 4
V79.20.01ZB
• ZR628
• ZR638
Issues Corrected
V79.20.01Z
• ZR628
• ZR638
Changes
155
Default Value: "on"

Service):
Discovery Data
transmitted:
Printer Settings
156

Printer Settings
media.type
ezpl.media_type
each command.
157
Issues Corrected
• The SGD command power.low_battery_timeout_alt is now read/write.
• Bluetooth connectivity has been improved so that it will not disconnect during a network reset (~WR).
instead.
• The printer will now come back on-line after being rebooted while in the cradle when the battery is fully
charged.
button is pressed.
avoid conflicts.
• Charging while the printer is turned on has been optimized to eliminate unneeded charge cycles.
158
enum type.
• The CHARGING TEMP FAULT message system has been optimized to be more accurate.
159
Link-OS 3
V79.19.15Z
• ZR628
• ZR638
Changes
Issues Corrected
V79.19.12Z
• ZR628
• ZR638
None.
160
V80 Printer OS
Release Notes
Link-OS 5 ..........................................................................................................................................................161
V80.20.10Z ...............................................................................................................................................161
Link-OS 4 ..........................................................................................................................................................165
V80.20.09Z ...............................................................................................................................................165
V80.20.06ZB .............................................................................................................................................165
V80.20.04Z ...............................................................................................................................................165
V80.20.03Z ...............................................................................................................................................166
Link-OS 5
V80.20.10Z
• ZT510
• ZT610
• ZT620
Changes
details):
161

• OpenSLL v1.0.21
details):
modes as follows:
access.
162


remote device.

request.
the passkey.

request.

Value
Issues Corrected
• The maximum label length for 600 dpi printers is now 32.35 inches.
163
disconnects.
printed on them.
"media.tof_tune"
media.tof_adjust.
• Example:

• Range: 95.0 to 105.0.
• Example:
164
Link-OS 4
V80.20.09Z
• ZT510
• ZT610
• ZT620
Issues Corrected
Contrast control on the ZT510 has been improved to maintain consistency.
V80.20.06ZB
• ZT510
• ZT610
• ZT620
Issues Corrected
V80.20.04Z
• ZT510
• ZT610
• ZT620
Changes
The ZT510 is now supported.
165
Issues Corrected
• Cut positioning has been optimized for the ZT510 printer.
• Ethernet driver now supports polarity auto-detection.
• Front panel contrast settings have been optimized to reduce ghosting.
V80.20.03Z
• ZT610
• ZT620
This is the initial release of this new printer OS build.
166
V81 Printer OS
Release Notes
Link-OS 5 ..........................................................................................................................................................167
V81.20.10Z ...............................................................................................................................................167
Link-OS 4 ..........................................................................................................................................................171
V81.20.06ZB .............................................................................................................................................171
V81.20.06Z ...............................................................................................................................................171
Link-OS 5
V81.20.10Z
• ZQ310
• ZQ320
Changes
details):
167

• OpenSLL v1.0.21
products:

details):
modes as follows:
access.
168


remote device.
request.
the passkey.
request.

Value
Issue Corrected
169
disconnects.
"media.tof_tune"
media.tof_adjust.
• Example:

• Range: 95.0 to 105.0.
• Example:
170
Link-OS 4
V81.20.06ZB
• ZQ310
• ZQ320
Issues Corrected
V81.20.06Z
This is the initial release of this printer OS. It is for use with the following printer models:
• ZQ310
• ZQ320
171
V82 Printer OS
Release Notes
Link-OS 5 ..........................................................................................................................................................172
V82.20.10Z ...............................................................................................................................................172
Link-OS 4 ..........................................................................................................................................................176
V82.20.06ZB .............................................................................................................................................176
V82.20.06Z ...............................................................................................................................................176
Link-OS 5
V82.20.10Z
• ZR318
• ZR328
Changes
details):
172

• OpenSLL v1.0.21
products:

details):
modes as follows:
access.
173


passkey.

Value
Issue Corrected
disconnects.
174

"media.tof_tune"
media.tof_adjust.
• Example:

• Range: 95.0 to 105.0.
• Example:
175
Link-OS 4
V82.20.06ZB
• ZR318
• ZR328
Issues Corrected
V82.20.06Z
This is the initial release of this printer OS. It is for use with the following printer models:
• ZR318
• ZR328
176
V83 Printer OS
Release Notes
V83.20.14Z
• ZD510 HC
Changes
• This is the initial release of this firmware.
177
V84 Printer OS
Release Notes
Link-OS 5 ..........................................................................................................................................................178
V84.20.10Z ...............................................................................................................................................178
Link-OS 4 ..........................................................................................................................................................182
V84.20.07Z ...............................................................................................................................................182
V84.20.05ZB .............................................................................................................................................182
V84.20.05Z ................................................................................................................................................183
V77.20.01Z ...............................................................................................................................................184
Link-OS 3 ..........................................................................................................................................................188
V77.19.17Z ................................................................................................................................................188
V77.19.16Z ................................................................................................................................................188
V77.19.14Z ................................................................................................................................................188
Link-OS 5
V84.20.10Z
• ZD410, ZD420
• ZD620
NOTE: The ZD400 series printers now use the V84 build of the printer OS, instead of the V77 build.
Changes
details):
178

• OpenSLL v1.0.21
details):
• NOTE: bluetooth.minimum_security_mode – This SGD now applies to both Classic and Low
Energy devices. Its functionality for Classic devices remains unchanged; its value affects LE
security modes as follows:
access.
179


remote device.
request.
the passkey.
request.

Value
Issues Corrected
180
disconnects.
"media.tof_tune"
media.tof_adjust.
• Example:

• Range: 95.0 to 105.0.
• Example:
181
Link-OS 4
V84.20.07Z
• ZD410, ZD420
• ZD620
Changes
This release adds support for the Direct Thermal-only ZD420 and ZD620 printers.
Issues Corrected
None.
V84.20.05ZB
• ZD410, ZD420
• ZD620
Issues Corrected
182
V84.20.05Z
This Printer OS release includes all features of the previous V77.20.01Z build, unless noted otherwise. It is
• ZD410, ZD420
• ZD620
Changes
• The printer operating system for the ZD400 series printers is now based on the V84 build of the OS,
rather than the V77 build.
• A new SGD command, power.hold_cur, with the choices on and off, has been created. This
command can be used to address vertical registration shift when using narrow media.
• Users can now adjust the vertical (or y coordinate) dots per inch (DPI) the printer uses by means of the
print.vertical_dpi_adjust command, which uses default of 100%, and a range of 95.0 to 105.0%.
By way of an example, if the command:
was used and the current label height was set to 2000 dots, it will be changed to 97.8% of 2000, or
1956 dots. In addition, a field y-coordinate specified as 1000 dots will be change to 97.8% of 1000, or
978 dots. Consequently, a box with a height of 500 dots will be reduced to 97.8% of 500, or 489 dots.
Care should be taken when using this command to ensure that bar code scan-ability is maintained as
content will be scaled to comply with the current "print.vertical_dpi_adjust" setting.
Issues Corrected:
• WLAN roaming has been improved.
• The printer will now check media out status when coming out of sleep mode.
• Print head shutdown is now included in the Discovery packet and ~HQES response
• The bluetooth.enable_reconnect default setting has been adjusted to correctly reflect which options
are available.
183
V77.20.01Z
• ZD410
• ZD420
Changes
zebra.com.
Default Value: "on"

Service):
184
Discovery Data
transmitted:
Printer Settings

Printer Settings
185
Printer Settings
media.type
ezpl.media_type
each command.
186
Issues Corrected
instead.
avoid conflicts.
enum type.
Motion.
• The ribbon.cartridge SGD commands have been corrected to offer the correct range information.
187
Link-OS 3
V77.19.17Z
This firmware includes all features of the previous V77.19.16Z release. It is for use with the following
printer models:
• ZD410
• ZD420
Changes
• The ZD420 is now supported.
Issues Corrected
• Improved handling with synthetic media.
V77.19.16Z
This firmware includes all features of the previous V77.19.14Z release. It is for use with the following
printer models:
• ZD410
• ZD420
Changes
• The ZD420 is now supported.
Issues Corrected
• The performance of the EPL command GW has been optimized.
V77.19.14Z
• ZD410
Changes
188
V85 Printer OS
Release Notes
V85.20.11Z
• ZQ610
• ZQ620
Changes
189
V86 Printer OS
Release Notes
V86.20.11Z
• ZR658
• ZR668
Changes
190
V93 Printer OS
Release Notes
V93.21.06Z
This Printer OS release is for use with the following printer models:
• ZD421, ZD421d, ZD421t
• ZD621d, ZD621t
Changes
• Initial release.
191
V94 Printer OS
Release Notes
V94.21.08Z
• ZE511
• ZE521
Changes
• No changes.
Issues Corrected
• Throughput improved when in Tear Off mode.
V94.21.07Z
• ZE511
• ZE521
Changes
• Initial release.
192
zebra.com

Link OS v6.4ReleaseNotes

Uploaded by

Copyright:

Available Formats

Link OS v6.4ReleaseNotes

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Link OS v6.4ReleaseNotes

Uploaded by

Copyright:

Available Formats

Link-OS

Newer releases by Link-OS version

Older releases by firmware version

Table 1 Printer Firmware Versions

Table 1 Printer Firmware Versions (Continued)

Printer Models OS Branch Build Printer Models OS Branch Build

Frequently Asked Questions:

Printer Models OS Branch Build Printer Models OS Branch Build

Frequently Asked Questions:

Printer Models OS Branch Build Printer Models OS Branch Build

Frequently Asked Questions:

Printer Models OS Branch Build Printer Models OS Branch Build

New Supplies Use Visibility features have been added.

• A new “zbrSuppliesMediaCartTable” SNMP table has been added: .1.3.6.1.4.1.10642.48.1.3

• The number of labels remaining on the roll (future use)

Frequently Asked Questions:

Security Related Items:

Printer Models OS Branch Build Printer Models OS Branch Build

Frequently Asked Questions:

Version Number: V85.20.16 (Based on Link-OS v5.2)

Release Date: 8 April 2019

Build Number: 20.16Z

Release Date: 15 January 2019

Build Number: 20.15Z

Frequently Asked Questions

NOTE: 802.11r is supported only on the 802.11ac WLAN radio.

• QLn220 • QLn220 Healthcare

QLn series ZQ500 series iMZ series ZQ3 series

• bluetooth.allow_non_display_numeric_comparison – This command now applies to both Classic

SGD Value I/O Capabilities Affect on LE

Command Name Use This Command Instead

• QLn220 • QLn220 Healthcare

• QLn220 • QLn220 Healthcare

To send the commands:

Settings and Alerts Data

• QLn220 • QLn220 Healthcare

• QLn220 • QLn220 Healthcare

This firmware includes all features of the previous V68.19.6Z release.

• Bluetooth Pairing QR code:

display.suppress_all_alerts Temporarily suppresses alerts.

display.root_wml Controls which index.wml file to use:

Non-Link-OS Firmware Builds

• 802.11: Add WIFI certification for 802.11 n radio (QNx-xxNxxxxx-xx)

Bluetooth® Key Bonding

! U1 setvar "bluetooth bonding" "on"

Configuring the 802.11 n Country Code

Group wlan.region_code wlan.country code choices

! U1 getvar "wlan.region _ code"

• If wlan.region_code is set to “rest of world”, it is not possible to configure the

Common Mirror Application Directory

Increase the Maximum TOF Setting for the QLn320

New SGD Parameter media.feed_skip and CPCL Registration Error

Potential Issue When Updating Firmware to V68.18.3Z

File.dir_format SGD Command

ZPL Notes for QLn

• ^ZZ - Printer Sleep

ZPL Override Command

Saving the 2-Key Report to a File

! U1 do "device.save _ 2key" "now"