Transducer

up to 4500 mm
Touchless Absolute
Series TLM with Start/
Stop-, SSI-, DyMoS-,
Analog- Interface

Special features Transducers employ the The high mechanical ruggedness Stop pulse interface and analog
• absolute transducer, no slide NOVOSTRICTIVE® touchless of the transducer combined with voltage or current interfaces, a
arm required magnetostrictive measuring the underlying measuring tech- high-dynamic serial DyMoS®
• NOVOSTRICTIVE®, touchless process for direct, precise and nique mean that the system is interface with data transfer moni-
magnetostrictive measuring absolute measurement of linear highly resistant to shock and toring is offered.
process position in control, positioning and vibration.
• high-dynamic serial DyMoS®- measuring technology. The advantages of conventional
interface with data transmission The active sensing element is interfaces and bus interfaces have
monitoring The measurement is accom- encased in an aluminum housing been combined in Novotechnik’s
• non-contacting guiding with plished using a passive position rated to IP 67. This makes the DyMoS® interface. In addition to
floating position marker marker which can be moved as a transducer resistant to contami- the position value, the DyMoS®
• unlimited mechanical life free-floating or guided element. nation, dust, moisture and oils. interface also allows the actual
• no velocity limit for position traverse velocity to be sent.
marker Side coupling of the position Mounting is accomplished using The pulse interface also allows
• outstanding linearity perform- marker reduces the installation clamps that allow precise fully toleranced processing of
ance up to 30 µm envelope size, prevents the pump mechanical adjustment. both edges of the Start/Stop
• resolution up to 0.001 mm effect of slide arms and permits signal. As an option, the trans-
regardless of stroke length stroke lengths up to 4500 mm. A sophisticated ASIC in the trans- ducer can also be operated with
• analog interfaces have end-user ducer provides for standard multiple position markers.
output range programming The non-contact coupling version absolute output signals. In addi-
capability makes installation even simpler, tion to the familiar interfaces such Additional interfaces see separate
• low temperature coefficient and the wear-free operation as the synchronous serial inter- data sheet.
<20 ppm/K means unlimited mechanical life face (24 or 25 bits), the Start/
• insensitive to shock and expectancy and unlimited traverse
vibration speed of the position marker. Description
• optionally cable or plug The temperature coefficient of the Housing Anodized aluminium with metal end cap
connection transducer is extremely low due Mounting Compression clamps, longitudinally adjustable
• protection class IP67 / IP68 to the measuring principle, design Position marker Floating marker, plastic
and selected materials. guided marker, ball coupling
Measuring technique NOVOSTRICTIVE®, touchless magnetostrictive
Electrical connection 8-pin round connector, shielded, M12x1
8-pin round connector, shielded, IEC130-9
8-conductor cable, shielded, 1 m long
Electronics Integrated SMD with ASIC
Connect cable shield to housing
 Novotechnik U.S., Inc.
155 Northboro Road
Southborough, MA 01772

Phone: 508-485-2244
Fax: 508-485-2430
Email: info@novotechnik.com

Connector pin Cable colors Connector with cable Start/Stop pulse interface SSI interface DyMoS® interface Analog interfaces
code 101, 102 code 201, 203, 205 EEM33-86, EEM33-87

PIN 1 YE WH + INIT + Clk + Clk 0(4)...20 mA

PIN 2 GY BN + Start/Stop + Data + Data 1 Signal GND

PIN 3 PK GN - INIT - Clk - Clk +10...0 (-10) VDC

PIN 4 RD YE open open - Data 2 open

PIN 5 GN GY - Start/Stop - Data - Data 1 0 (-10)...+10 VDC

PIN 6 BU PK supply voltage GND supply voltage GND supply voltage GND supply voltage GND

PIN 7 BN BU +24 VDC +24 VDC +24 VDC +24 VDC

PIN 8 WH RD open open + Data 2 open

Additional interfaces see separate The unipolar analog interfaces Important

data sheets. includes standard teach-in Avoid equalizing currents in the
function via the electrical cable shield caused by potential
connection. differences. Twisted pair cable is
recommended. Subject to changes
© February 2007
Novotechnik U.S., Inc. All rights reserved.
Type designations TLM xxxx 001 1xx xxx TLM xxxx 001 2xx xxx TLM xxxx 001 3xx xxx Analog interfaces
Start/Stop pulse interface Synchronous serial interface DyMoS® interface
Electrical Data
Defined electrical range from 50 to 4500 from 50 to 4500 from 50 to 4500 from 50 to 4500 mm
(dimension B)
Absolute linearity ± 50 µm ≤ ± 30 µm ≤ ± 30 µm ≤ ± 0,02 % (min. 50 µm)
Output signal impulse digital digital 0 (-10)...10 VDC (load ≥10 kΩ)
0 (4)...20 mA (burden ≤500Ω)
Resolution ≤ 2 µm ≤ 1 digit ≤ 1 digit ≤ 0.01%
Reproducibility ≤ 6 µm ≤ 2 digits ≤ 2 digits ≤ 0.02%
Hysteresis ≤ 4 µm ≤ 1 digit ≤ 1 digit ≤ 0.01%
Supply voltage 24 ± 20% 24 ± 20% 24 ± 20% 24 ± 20% VDC
reverse polarity protected reverse polarity protected reverse polarity protected reverse polarity protected
Supply voltage ripple max. 10% max. 10% max. 10% max. 10% Vpp
Current draw ≤ 100 typical ≤ 100 typical ≤ 100 typical ≤ 100 typical mA
Output update rate 16 16 16 ≤ 16 kHz
Shielding connected to housing connected to housing connected to housing connected to housing
Temperature coefficient ≤ 20 ≤ 20 ≤ 20 30 ppm/K
Overvoltage protection 40 (Transzorb protection diodes) 40 (Transzorb protection diodes) 40 (Transzorb protection diodes) 40 (Transzorb protection diodes) VDC
Reverse voltage yes yes yes yes
Insulation resistance ≥ 10 ≥ 10 ≥ 10 ≥ 10 MΩ
(500 V, 1 bar, 2 s)
Mechanical Data
Dimensions see drawing see drawing see drawing see drawing
Physical length (dimension A) Dimension B + 160 Dimension B + 160 Dimension B + 160 Dimension B + 160 ± 2 mm
Environmental Data
Operating temperature range -40...+85 -40...+85 -40...+85 -40...+85 °C
Storage temperature range -40...+120 -40...+120 -40...+120 -40...+120 °C
Operating humidity range 0...100 0...100 0...100 0...100 %R.H.
Shock per DIN IEC68T2-27 100 (11 ms) 100 (11 ms) 100 (11 ms) 100 (11 ms) g
Vibration per DIN IEC68T2-6 20 (5...2000 Hz,Amax = 0.75 mm) 20 (5...2000 Hz,Amax = 0.75 mm) 20 (5...2000 Hz,Amax = 0.75 mm) 20 (5...2000 Hz,Amax = 0.75 mm) g
Protection class per IP67 with fastened connector IP67 with fastened connector IP67 with fastened connector IP67 with fastened connector
DIN 40050 IEC 529 IP68 with cable connection IP68 with cable connection IP68 with cable connection IP68 with cable connection
Mechanical data when used with unguided position marker
Traverse speed of unlimited unlimited unlimited unlimited ms-1
position marker
Traverse acceleration of unlimited unlimited unlimited unlimited ms-2
position marker
Life unlimited (mechanical) unlimited (mechanical) unlimited (mechanical) unlimited (mechanical) movements
Standard defined electr. range 50 up to 1000 in 50 mm steps, 1000 up to 2000 in 100 mm steps, 2000 up to 4500 in 250 mm steps; other lengths in 10 mm steps on request
(dimension B)
CE-conformity

Emissions RF noise field strength EN 55011 Group 1 Class A

Noise immunity ESD EN 61000-4-2

Radiated immunity EN 61000-4-3
BURST EN 61000-4-4
Conducted disturbances induced by RF fields EN 61000-4-6
 Novotechnik U.S., Inc.
155 Northboro Road
Southborough, MA 01772

Phone: 508-485-2244
Fax: 508-485-2430
Email: info@novotechnik.com

Z-TLM-P01

Z-TLM-P04 Z-TLM-P05

Output signal Impulse Interface 1XX Included in delivery

Ordering specifications 1 Standard: Start Stop Signal (P) (M) Mounting clamps Z46, electrically
2 Alternative: Measuring time / impulse range (L)
isolating incl. fillister head screws
Electr. Interface Output signal Synchronous Serial Interface 2XX Required accessories
1 Standard: Impulse Interface, supply voltage 24 VDC ±20% 1 Standard: 24 Bit
2 Alternative: 25 Bit Floating position marker
2 Optional: Synchronous Serial Interface, supply voltage 24VDC ±20%
3 Optional: DyMoS®-Interface, supply voltage 24 VDC ±20% Output signal DyMoS® Interface 3XX
Z-TLM-P01, Art.No. 005651;
4 Optional: Analog Interface, supply voltage 24 VDC ±20% 1 Standard: Pos. 1 + Vel. 1 Z-TLM-P04, Art.No. 005654;
2 Alternative: Pos. 1 + Pos. 2 Guided position marker
3 Optional: (Pos. 1 + Vel. 1) and (Pos 2 + Vel. 2) two channel
Z-TLM-P05, Art.No. 005655;
Output signal Analog Interface 4XX
1 Standard: Voltage output
Other pos. marker on request
2 Optional: Current output Recommended accessories
Impulse Interface Start Stop Signal 11X Connector IEC 130-9, EEM
4 Standard: Variable for 1 to 3 PG 33-84, IP67, Art.No. 005627;
Impulse Interface measuring time / impulse range 12X Angled connector IEC 130-9,
1 Standard EEM 33-85, IP67,
Synchronous Serial Interface 2XX Art.No. 005628;
1 Standard: Binary Code, resolution 5 µm
2 Alternative: Gray Code, resolution 5 µm
Connector M12x1, 2 m cable,
DyMoS® Interface 3XX
EEM 33-86, IP67,
1 Standard: Binary Code, resolution 5 µm Art.No. 005629;
Analog Interface voltage output 41X Angled connector M12x1,
1 Standard: 0 VDC...10 VDC and 10 VDC...0 VDC 2 m cable, EEM 33-87, IP67,
2 Alternative: 0 VDC...10 VDC (Pos. 1 + Pos. 2)
3 Optional: -10 VDC...+10 VDC, +10 VDC...-10 VDC
Art.No. 005630;
Connector with longer cable
Analog Interface current output 42X
1 Standard: 0 mA...20 mA length on request
2 Alternative: 20 mA...0 mA Available on request
3 Alternative: 4 mA...20 mA
4 Alternative: 20 mA...0 mA
Standard cable, 10 m
Specific connectors
Electrical connection
101 Alternative: 8 pin round connector IEC130-9 Other resolutions
102 Standard: 8 pin round connector M 12x1 SSI 26 Bit, SSI two-channel,
201 Alternative: NT standard cable 1 m
203 Optional: NT standard cable 3 m
Current output two-channel,
205 Optional: NT standard cable 5 m Incremental interface,
T L M 0 8 0 0 0 0 1 1 1 4 1 0 2 Field bus interface.

Defined electr. range

Several standard lengths
Series from 0050 to 4500 mm
Mech. configuration
001 Standard: Profile design
Subject to changes
© February 2007
Novotechnik U.S., Inc. All rights reserved.