Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
189 views

Power Electronics: THYRISTOR Protection

Thyristors like SCRs require protection from abnormal operating conditions to ensure reliable operation. This document discusses techniques for protecting SCRs from overcurrents (di/dt) and overvoltages (dv/dt) through the use of snubber circuits. A snubber circuit uses a resistor and capacitor in parallel with the SCR to limit the rate of rise of voltage (dv/dt) and current (di/dt) during switching and prevent device damage or unwanted triggering. The values of the snubber components are selected based on the device ratings and circuit parameters.

Uploaded by

K Lokesh Lingaiah
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
189 views

Power Electronics: THYRISTOR Protection

Thyristors like SCRs require protection from abnormal operating conditions to ensure reliable operation. This document discusses techniques for protecting SCRs from overcurrents (di/dt) and overvoltages (dv/dt) through the use of snubber circuits. A snubber circuit uses a resistor and capacitor in parallel with the SCR to limit the rate of rise of voltage (dv/dt) and current (di/dt) during switching and prevent device damage or unwanted triggering. The values of the snubber components are selected based on the device ratings and circuit parameters.

Uploaded by

K Lokesh Lingaiah
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 12

Power Electronics

THYRISTOR Protection
Thyristor protection circuits
• Reliable operation of a thyristor demands that its specified ratings
are not exceeded.
• In practice, a thyristor may be subjected to overvoltages or
overcurrents. During SCR turn-on, di/dt may be prohibitively
large.
• There may be false triggering of SCR by high value of dv/dt.
• A spurious signal across gate-cathode terminals may lead to
unwanted turn-on.
• A thyristor must be protected against all such abnormal
conditions for satisfactory and reliable operation of SCR circuit
and the equipment.
• SCRs are very delicate devices, their protection against abnormal
operating conditions is, therefore, essential.
• The object of this section is to discuss various techniques adopted
for the protection of SCRs.
– di/dt protection.
– dv/dtprotection.
di/dt protection
• When a thyristor is forward biased and is turned on by a gate pulse,
conduction of anode current begins in the immediate neighbourhood of
the gate-cathode junction.

• Thereafter, the current spreads across the whole area of junction.

• The thyristor design permits the spread of conduction to the whole


junction area as rapidly as possible.

• However, if the rate of rise of anode current, i.e. di/dt, is large as


compared to the spread velocity of carriers, local hot spots will be
formed near the gate connection on account of high current density.
di/dt protection
• This localized heating may destroy the thyristor. Therefore,
the rate of rise of anode current at the time of turn-on must
be kept below the specified limiting value.

• The value of di/dt can be maintained below acceptable limit


by using a small inductor, called di/dt inductor, in series with
the anode circuit. Typical di/dt limit values of SCRs are 20-500
A/µ sec.

• Local spot heating can also be avoided by ensuring that the


conduction spreads to the whole area as rapidly as possible.
•
• This can be achieved by applying a gate current nearer to (but
never greater than) the maximum specified gate current.
di/dt Protection
• A thyristor requires a minimum time to spread the current conduction
uniformly throughout the junctions
• Otherwise, a localized “hot-spot” heating may occur due to high current
density.
dv/dt protection
• With forward voltage across the anode & cathode of a thyristor, the two
outer junctions (A & C) are forward biased but the inner junction (J2) is
reverse biased.

• The reversed biased junction J2 behaves like a capacitor because of the


space-charge present there.

• Let the capacitance of this junction be Cj. For any capacitor, i = C dv/dt.
• In case it is assumed that entire forward voltage va appears across
reverse biased junction J2 then charging current across the junction is
given by
– i = dQ/dt =d(Cj Va )/dt
– i=Cj (d Va /dt) + Va(d Cj /dt)
– i = Cj dva /dt
• This charging or displacement current across junction J2 is collector
currents of Q2 and Q1 Currents IC2, IC1 will induce emitter current in
Q2, Q1.
dv/dt protection
• In case rate of rise of anode voltage is large, the emitter currents will be
large and as a result, α1+ α2 will approach unity leading to eventual
switching action of the thyristor.

• If the rate of rise of forward voltage dVa/dt is high, the charging current i
will be more. This charging current plays the role of gate current and
turns on the SCR even when gate signal is zero.

• Such phenomena of turning-on a thyristor, called dv/dt turn-on must be


avoided as it leads to false operation of the thyristor circuit.

• For controllable operation of the thyristor, the rate of rise of forward


anode to cathode voltage dVa/dt must be kept below the specified rated
limit.

• Typical values of dv/dt are 20 – 500 V/µsec. False turn-on of a thyristor


by large dv/dt can be prevented by using a snubber circuit in parallel
with the device.
Snubber circuit
• A snubber circuit consists of a series combination of resistance Rs and capacitance Cs
in parallel with the thyristor as shown in Fig.
• Strictly speaking, a capacitor Cs in parallel with the device is sufficient to prevent
unwanted dv/dt triggering of the SCR.
• When switch S is closed, a sudden voltage appears across the circuit. Capacitor Cs
behaves like a short circuit, therefore voltage across SCR is zero.
• With the passage of time, voltage across Cs builds up at a slow rate such that dv/dt
across Cs and therefore across SCR is less than the specified maximum dv/dt rating
of the device.
• Here the question arises that if Cs is enough to prevent accidental turn-on of the
device by dv/dt, what is the need of putting Rs in series with Cs ? The answer to this
is as under.
snubber circuit (continue……)
• Before SCR is fired by gate pulse, Cs charges to full voltage Vs.
When the SCR is turned on, capacitor discharges through the SCR
and sends a current equal to Vs / (resistance of local path formed
by Cs and SCR).
• As this resistance is quite low, the turn-on di/dt will tend to be
excessive and as a result, SCR may be destroyed. In order to limit
the magnitude of discharge current, a resistance Rs is inserted in
series with Cs as shown in Fig.
• Now when SCR is turned on, initial discharge current Vs/Rs is
relatively small and turn-on di/dt is reduced.
• In actual practice ; Rs, Cs and the load circuit parameters should
be such that dv/dt across Cs during its charging is less than the
specified dv/dt rating of the SCR and discharge current at the
turn-on of SCR is within reasonable limits.
• Normally, Rs Cs and load circuit parameters form an
underdamped or critically damped circuit so that dv/dt is limited
to acceptable values.
RCD SNUBBERS

 In general, snubbers are used for:

– turn-on: to minimize large overcurrents through the device at turn-on

– turn-off: to minimize large overvoltages across the device during turn-


off.

– Stress reduction: to shape the device switching waveform such that the
voltage and current associated with the device are not high simultaneously.
Designing the snubber circuit

• Applying KVL for the closed path when the switch is


closed at instant t (capacitor behaves as short circuit)
• Es = is(Rs+RL)+Lsdi/dt which is first order equation
whose solution is
• i = I(1 – e–t/τ) where I = ES/(Rs+RL) and τ = LS/(Rs+RL)
• Differentiating the above expression
• di/dt = 1/ τ (Ie–t/τ) = (Es/Ls) e–t/τ
• This is maximum when t = 0 ie
• (di/dt)max = (Es/Ls) e–0/τ or Es/Ls
• Or Ls = Es/(di/dt)max
• Calculation of R
• Voltage across SCR may be given by
• Va = Rsi differentiating the above
• dVa/dt = Rsdi/dt. This max when
• (dVa/dt)max = Rs (di/dt)max
• Or Rs = L/Es (dVa/dt)max
• Calculation of C – when the the switch is closed and SCR is still
not ON, the circuit is second order circuit and for critically
damped system the value of Cs is given by
 2 
2

Cs    L
 R

You might also like