Transmission: Cerrar SIS Pantalla Anterior
Transmission: Cerrar SIS Pantalla Anterior
Page 1 of 54
Cerrar SIS
Pantalla anterior
Producto: WHEEL LOADER
Modelo: 936 WHEEL LOADER 45Z
Configuración: 936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGINE
Desarmado y Armado
936 WHEEL LOADER POWER TRAIN
Número de medio -SENR2911-01 Fecha de publicación -01/10/2004 Fecha de actualización -13/06/2005
SENR29110031
Transmission
SMCS - 3150-015; 3150-016
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGINE(... Page 2 of 54
Disassemble Transmission
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGINE(... Page 3 of 54
START BY:
*
See Disassemble Transfer Gears.
2. Install the transmission assembly on tooling (A). The weight of the transmission and case is 340 kg
(750 lb.).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGINE(... Page 4 of 54
4. Remove two bolts (3), and make a separation of the transmission planetary group from case (4).
The weight of the transmission planetary group is 263 kg (580 lb.).
5. Remove O-rings (5) and O-ring seal (6) from transmission case (4).
6. Fasten tooling (C) and a hoist to transmission planetary group (7) as shown.
7. Carefully turn the transmission planetary group over, and install it on tooling (A) as shown.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGINE(... Page 5 of 54
8. Use tool (D), and remove retaining ring (8) from the shaft.
11. Use a hammer and punch to push the pins through carrier (9) into shafts (11).
12. Use a hammer and punch, and remove shafts (11) from the carrier.
13. Remove discs (14), bearing assemblies (12) and gears (13) from the carrier. Remove pins (15)
from shafts (11).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGINE(... Page 6 of 54
14. Remove bolts (16) that hold No. 6 (first speed) clutch housing (17) to the transmission planetary
group.
15. Install tooling (E) to hold plate (18) and the piston in the No. 6 clutch housing as shown.
16. Remove No. 6 clutch housing (17) from the planetary group.
18. Remove piston (19) and three pins (20) from the No. 6 clutch housing.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGINE(... Page 7 of 54
19. Remove seal rings (21) and (22) from the piston.
20. Remove springs (24), three discs (25) and three remaining plates (26) (first speed).
22. Use tool (F) to remove retaining ring (27) from the shaft.
23. Use tool (D), and remove retaining ring (28) from the housing.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGINE(... Page 8 of 54
24. Remove bolts (30) that hold housing (29) to the planetary group.
25. Install tooling (C) and a hoist, and remove housing (29) from the planetary group. The weight of
the housing is 31 kg (68 lb.).
26. Use tool (F), and remove retaining ring (31) from the housing.
27. Use tool (H) to remove the bearing from the housing.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGINE(... Page 9 of 54
28. Use tool (G) to compress retaining ring (33), and remove housing assembly (32). Remove
retaining ring (33) from the housing assembly.
29. Use plate (34) which is approximately 152 mm (6.00 in.) long x 25.4 mm (1.00 in.) wide x 10 mm
(3.93 in.) thick, two 1/2 in. nuts and a press to put plate (36) and the bevel springs under compression.
Remove retaining ring (35) from the gear.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 10 of 54
36. Do not remove seal carrier (42) from the housing unless it is worn or damaged. Use a hammer and
chisel to break the carrier and remove it. After carrier (42) is removed, remove the pin that holds the
carrier in position on the housing.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 11 of 54
38. Remove two discs (44) and two plates (46) (third speed).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 12 of 54
42. Remove three discs (50) and two plates (second speed) from gear (49).
43. Use a screwdriver, and remove ring (51) and plate (52) from the gear.
44. Remove piston (53) from the No. 3 and No. 4 clutch housing.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 13 of 54
46. Install tooling (J) to hold plate (56) and the piston in No. 3 and No. 4 clutch housing.
47. Install tooling (K) and a hoist, and remove No. 3 and No. 4 clutch housing (57). The weight of the
clutch housing is 26 kg (58 lb.).
48. Remove plate (56) from the No. 3 and No. 4 clutch housing.
49. Remove piston (58) from the No. 3 and No. 4 clutch housing.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 14 of 54
50. Remove seal rings (59) and (60) from piston (58).
51. Remove springs (63) and rods (62) from the housings.
52. Remove three discs (61) and two plates (64) (fourth speed).
53. Remove carrier (65) and gear (66) as a unit from the clutch housing.
54. Use 3.18 mm (.125 in.) diameter rods (67) with a point ground on one end to put the retaining ring
under compression that holds carrier (65) and gear (66) together. Install rods (67) between the
retaining ring and gear (66) to compress the retaining ring into carrier (65).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 15 of 54
57. Use a hammer and a punch to push the pins through carrier (65) and into shafts (69).
58. Use a hammer and a punch, and remove shafts (69) from carrier (65).
59. Remove discs (72), bearing assemblies (70) and gears (71) from the carrier. Remove pins (73)
from shafts (69).
60. Remove ring (74) that holds bearing (76) in the carrier.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 16 of 54
61. Remove shaft (75) and bearing (76) as a unit from the carrier.
62. Use tool (F), and remove ring (78) from shaft (75).
64. Use tooling (L) and a press, and push shaft (75) out of bearing (79) as shown.
65. If necessary, remove bearing (80) from both ends of shaft (75).
66. Remove three bolts (82) that hold housing (81) to the planetary group.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 17 of 54
67. Use tooling (E) to hold plate (84) and the piston in the No. 2 clutch housing.
68. Install tooling (C) and a hoist, and remove No. 2 clutch housing (83). The weight of the clutch
housing is approximately 18 kg (40 lb.).
71. Remove seal rings (86) and (87) from piston (85).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 18 of 54
73. Remove three discs (88) and two plates (90) (forward).
76. Remove carrier (94) and gear (95) as a unit from the clutch housing.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 19 of 54
77. Use 3.18 mm (.125 in.) diameter rods (96) with a point ground on one end to put the retaining ring
under compression that holds carrier (94) and the gear together. Install rods (96) between the retaining
ring and gear (95) to compress the retaining ring into carrier (94).
80. Use a hammer and a punch to push the pins through carrier (94) and into shafts (98).
81. Use a hammer and punch, and remove shafts (98) from carrier (94).
82. Remove discs (100), bearing assemblies (101) and gears (99) from the carrier. Remove pins (102)
from shafts (98).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 20 of 54
83. Use tool (F) to expand ring (104) into carrier (94). Use tooling (H) to remove bearing (103) and
gear as a unit from the carrier.
84. Use a press, and remove bearing (103) from gear (105).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 21 of 54
87. Remove three discs (109) and three plates (110) (reverse) from the No. 1 clutch housing.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 22 of 54
92. Use a hammer and a punch to push the pins through carrier (108) and into the shafts.
93. Use a hammer and a punch, and remove the shafts from carrier (108).
94. Remove disc (118), gears (115) and bearing assemblies (116) from the carrier. Remove pins (119)
from shafts (117).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 23 of 54
98. Remove seal rings (123) and (124) from piston (122).
100. Remove the shaft and No. 1 clutch housing as a unit from tooling (A). The weight of the shaft
and housing is 52 kg (115 lb.).
101. Remove bolt (127), retainer (129) and gear (128) from the end of shaft ((125).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 24 of 54
102. Remove retaining ring (130) that holds the bearing and support in position in the No. 1 clutch
housing.
103. Use a soft hammer, and remove shaft (125) and the bearing as a unit from the No. 1 clutch
housing.
105. Use a press and tool (M) to remove bearing (132) from the shaft.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 25 of 54
Assemble Transmission
NOTE: Inspect all parts for wear or damage, and make replacements if needed. Put clean
transmission oil on the parts at assembly.
1. Install a dowel (2) in each side of No. 1 clutch housing (1). The dowels must be installed until they
are 10.5 ± .5 mm (.41 ± .02 in.) above outside surface (X).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 26 of 54
2. Heat bearing (4) to a maximum temperature of 135°C (275°F), and install it on shaft (3) as shown.
3. Install seal rings (5) and (6) on shaft (3). Make sure the hooked ends of the rings are engaged after
the rings are installed.
NOTICE
Align shaft (3) so that the hooked ends of seal (6) are not in alignment
with the oil cavity in the No. 1 clutch housing. Make sure seals (5) and
(6) are not damaged when the shaft is installed in the bore of the
housing.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 27 of 54
5. Install retaining ring (7) in the No. 1 clutch housing to hold the shaft and bearing in place.
7. Install retainer (9) and bolt (10) to hold the gear in place. Tighten the bolt to a torque of 110 ± 10
N·m (80 ± 7 lb.ft.).
8. Install the shaft and No. 1 clutch housing as a unit on tooling (A) as shown. The weight of the shaft
and housing is 52 kg (115 lb.).
9. Install seal ring (11) on shaft (3). Make sure the hooked ends of the rings are engaged after the
rings are installed.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 28 of 54
10. Install seal rings (12) and (14) on piston (13). Make sure the seal rings are installed with the lip of
the seals up as shown.
11. Install piston (13) in the No. 1 clutch housing. Make sure the lip of the seals is down.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 29 of 54
16. Install shafts (19) that hold the discs, gears and bearing assemblies in carrier (22).
17. Use a hammer and a punch to install pins (21) that hold the shafts in the carrier. Make sure the
pins are installed even with the counterbore in the carrier.
18. Install seal rings (23) on carrier (22). Make sure the hooked ends of the ring are engaged after the
ring is installed.
19. Install seal ring (25) on carrier (24). Make sure the hooked ends of the ring are engaged after the
ring is installed.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 30 of 54
21. Make an alignment of carrier (22) with gear (16) on the shaft and carrier (22) with gear (15).
Install carrier (22) in the No. 1 clutch housing.
22. Install plate (28) in the No. 1 clutch housing so the small holes in the plate are in alignment with
small holes in the housing.
23. Install three discs (26) and two remaining plates (27) (reverse) in the No. 1 clutch housing. Start
and stop with a disc.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 31 of 54
24. Put plate (29) in position on the No. 1 clutch housing as shown.
25. Heat bearing (30) to a maximum temperature of 135°C (275°F), and install it on gear (31). Make
sure the bearing is installed so the groove is toward the top as shown.
26. Install retaining ring (32) in the groove of carrier (33) as shown.
27. Use tool (B) to expand retaining ring (32). Use tool (C) and a press to install bearing (30) and gear
(31) as a unit in carrier (33). Ring (32) must engage in the groove of bearing (30).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 32 of 54
29. Install discs (34) and gears (35) in the bottom and top of carrier (33).
30. Install shafts (36) that hold the discs, gears and bearing assemblies in carrier (33).
31. Use a hammer and a punch to install pins (38) that hold the shafts in carrier (33). Make sure the
pins are installed even with the counterbore in the carrier.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 33 of 54
33. Compress retaining ring (39), and install carrier (33) in gear (40) until the retaining ring engages
into the groove in gear (40).
34. Put carrier (33) and gear (40) as a unit in position on carrier (22) in the No. 1 clutch housing. Turn
shaft (3) to make sure gear (40) is correctly engaged with the gears in carrier (22).
35. Use tool (B) to install retaining ring (41) that holds the carrier in place.
36. Install gear (42) on carrier (33). Make sure the gear is correctly engaged with the gears in carrier
(33).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 34 of 54
37. Install three discs (43) and two plates (44) on plate (29). Start and stop with a disc.
39. Install seal rings (46) and (47) on piston (48). Make sure the seal rings are installed with the lips
of the seals up as shown.
40. Install piston (48) in No. 2 clutch housing (49). Make sure the lip of the seals is down.
41. Install plate (50) in the No. 2 clutch housing so the small holes in the plate are in alignment with
the small holes in the housing.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 35 of 54
42. Install tooling (D) to hold the piston and plate in the No. 2 clutch housing.
43. Put No. 2 clutch housing (49) in position on plate (29) as shown. The weight of the clutch housing
is 18 kg (40 lb.).
44. Install three bolts (51) that hold the two housings and plate together. Install the bolts until they are
approximately 1.588 to 3.18 mm (.0625 to .1250 in.) from the surface of clutch housing (49).
45. If bearings (52) were removed, lower the temperature of the two bearings, and put them in
position in both ends of shaft (53). Use tool (F) to install the bearings until they are 12.0 ± 0.5 (.47
± .02 in.) from the end of the shaft. The inside diameter of the bearings must be 34.988 ± .039 mm
(1.3775 ± .0015 in.) after assembly.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 36 of 54
46. Heat bearings (54) to a maximum temperaturr of 135° C (275° F), and install it on the shaft as
shown. Make sure ball (55) in the shaft fits into the notch in the bearing, and the groove (slot) in the
bearing is toward the top of the shaft.
48. Use tool (B) to install retaining ring (57) on the end of the shaft.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 37 of 54
50. Install retaining ring (58) in the carrier to hold shaft (53) in place.
53. Install shafts (61) that hold the discs, gears and bearing assemblies in carrier (64).
54. Use a hammer and a punch to install pins (63) that hold the shafts in the carrier. Make sure the
pins are installed even with the counterbore in carrier (64).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 38 of 54
55. Install seal ring (65) in the groove of carrier (64) as shown. Make sure the hooked ends of the ring
are engaged after the ring is installed.
56. Compress retaining ring (65), and install carrier (64) in gear (66) until the retaining ring engages
into the groove in gear (66).
57. Put carrier (64) and gear (66) as a unit in position on carrier (33) in the No. 1 clutch housing. Turn
shaft (53) to make sure gear (66) is correctly engaged with the gears in carrier (33).
58. Install three discs (67) and two plates (68) (fourth speed) on the No. 2 clutch housing. Start and
stop with a disc as shown.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 39 of 54
59. Put rods (69) in position through the housing assemblies and springs (45) as shown.
61. Install seal rings (72) and (73) on piston (71). Make sure the seal rings are installed with the lips
of the seals up as shown.
62. Install piston (71) in the No. 3 and No. 4 clutch housing. Make sure the lip of the seals is down.
63. Install plate (74) on the No. 3 and No. 4 clutch housing as shown. Make sure the larger holes in
the plate are in alignment with the larger holes in the clutch housing.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 40 of 54
64. Install tooling (G) to hold the piston and plate in the No. 3 and No. 4 clutch housing as shown.
65. Fasten tooling (H) and a hoist to No. 3 and No. 4 clutch housing, and install it on the No. 2 clutch
housing as shown. The weight of the clutch housing is 26 kg (58 lb.).
66. Install seal rings (76) and (77) on piston (75). Make sure the seal rings are installed with the lips
of the seals up as shown.
67. Install piston (75) in the No. 3 and No. 4 clutch housing. Make sure the lip of the seals is down.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 41 of 54
69. Install retaining ring (80) in the groove of gear (79) that holds plate (78) in place.
70. Install three discs (81) and two plates (82) (second speed) in the gear.
71. Put gear (79) in position on the carrier in the No. 3 and No. 4 clutch housing. Make sure the gear
is correctly engaged with the gears in the carrier.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 42 of 54
73. Use tool (B) to install retaining ring (84) in the groove of the shaft as shown.
74. Install two plates (85) and two discs (86) (third speed) on the No. 3 and No. 4 clutch housing as
shown. Make sure the small hole in plate (87) is installed on rods (69). Start with a plate and end with
a disc.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 43 of 54
76. If carrier (89) was removed from housing (90), heat the new carrier to a temperature of 127° to
166°C (260° to 330°F) for a maximum of ten minutes, and install it on housing (90) so the part
number can be seen after it is installed. Also, install the carrier with one of the grooves (slots) in the
carrier in alignment with the pin hole in the housing.
Figure 1. Correct Method To Make (Non-Metal) New Seal Rings Ready For Installation.
Figure 2. Wrong Method To Make (Non-Metal) New Seal Rings Ready For Installation.
NOTICE
New seal rings must be preloaded before they are installed to prevent
them from being damaged or broken when the clutch housing is
installed. There is a correct method to preload new seal rings prior to
installation. Place your hands on each end of the seal ring, and pull
(wind) the ends several inches past each other or until they almost
make contact. See Figure 1. Use care to keep the ring shaped like a
circle. This will make an even bend (or ring "set") all around the ring.
When the seal ring is in the groove of carrier (90) the ends must but
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 44 of 54
together lightly. Do not bend the seal ring as shown in Figure 2. This
does not make an even bend all the way around the ring.
Do not attempt to use this method to preload a used seal ring. Also, do
not use this procedure for cast iron seal rings. This will cause used or
cast iron seal rings to break.
79. Install seal ring (93) on piston (95). Make sure the seal ring is installed with the lip of the seal
down as shown.
80. Install seal ring (94) on piston (95). Make sure the seal ring is installed with the lip of the seal up
as shown.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 45 of 54
a. Install the first two springs with the outside diameter of the springs in contact with each other.
b. Install the next two springs with the outside diameter of the springs in contact with each other.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 46 of 54
84. Use plate (99) which is approximately 152 mm (6.00 in.) long x 25.4 mm (1.00 in.) wide x 10 mm
(3.93 in.) thick, two 1/2 in. nuts and a press to put plate (97) and bevel springs under compression.
Install retaining ring (98) on gear (92).
86. Put the housing assembly and gear in position in gear (79) as shown.
87. Use tool (J) to make a compression of retaining ring (101), and install the housing assembly until
the retaining ring engages in the groove in gear (79).
88. Use tooling (C), and install the bearing in housing (102).
89. Use tool (J) to install retaining ring (103) in the housing.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 47 of 54
NOTE: Make sure the dowel in gear (92) and the notch in bearing (105) are in alignment. If
necessary, turn gear (92) to make the alignment.
90. Install tool (E) and a hoist to housing (104), and put it in position on No. 3 and No. 4 clutch
housing. The weight of the housing is 31 kg (68 lb.).
91. Install the six bolts that hold housing (104) in place.
92. Tighten lower three bolts (51) that were installed in Step 44 to a torque of 110 ± 10 N·m (80 ± 7
lb.ft.).
93. Tighten upper bolts (106) that were installed in Step 91 to a torque of 110 ± 10 N·m (80 ± 7 lb.ft.).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 48 of 54
94. Use tool (K) to install retaining ring (107) on the housing assembly. If necessary, use a block of
wood and a pry bar to lift up on gear (92) while installing retaining ring (107) as shown.
95. Use tool (B) to install retaining ring (108) on the shaft.
97. Install three discs (112) and three plates (110) (first speed) on the housing. Start with a plate and
stop with a disc.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 49 of 54
99. Install seal rings (113) and (114) on piston (115). Make sure the rings are installed with the lip of
the seals up as shown.
100. Install piston (115) in No. 6 clutch housing (116). Make sure the lip of the seals is down.
102. Install plate (118) on pins (117) in the No. 6 clutch housing.
103. Install tooling (D) to hold the piston and plate in the No. 6 clutch housing.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 50 of 54
104. Put No. 6 clutch housing (116) in position on the housing as shown.
105. Install bolts (119) that hold the No. 6 clutch housing to the housing. Tighten the bolts to a torque
of 110 ± 10 N·m (81 ± 7 lb.ft.).
107. Install discs (123) and gears (121) in the bottom and top of carrier (125).
108. Install shafts (122) that hold the discs, gears and bearing assemblies in carrier (125).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 51 of 54
109. Use a hammer and a punch to install pins (124) that hold the shafts in the carrier. Make sure the
pins are installed even with the counterbore in the carrier.
110. Install seal ring (126) on carrier (125). Make sure the hooked ends of the rings are engaged after
the seal rings are installed.
111. Place carrier (125) in position over the shaft, and carefully install the carrier in the bore of
housing (116).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 52 of 54
112. Use tool (K) to install retaining ring (127) on the shaft.
113. Check to make sure the pistons are free in their clutch housings with tool (L) as follows:
a. Put air free of water under a pressure of 690 to 1030 kPa (100 to 150 psi) into each of the six oil
passages.
b. If the pistons do not move, put a small amount of clean SAE 30 oil in each passage. Check for
movement again. If the pistons still do not move, the transmission must be disassembled and the
pistons and seal rings checked.
114. Fasten tooling (E) and a hoist to the transmission planetary as shown.
115. Remove the transmission planetary group from tooling (A). The weight of the transmission
planetary group is 263 kg (580 lb.).
117. Install the transmission case on tooling (A) as shown. The weight of the transmission case is 79
kg (175 lb.).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 53 of 54
119. Fasten tooling (E) and a hoist to the transmission planetary group as shown.
121. Install two bolts (132) that hold the transmission planetary group and case together.
122. Fasten tooling (M) and a hoist to the transmission assembly as shown.
123. Remove the transmission assembly from tooling (A). The weight of the transmission assembly is
340 kg (750 lb.).
END BY:
*
See Assemble Transfer Gears.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGIN... Page 54 of 54
Copyright 1993 - 2021 Caterpillar Inc. Mon Aug 16 20:30:27 UTC-0300 2021
Todos los derechos reservados.
Red privada para licenciados del SIS.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/t... 16/8/2021