Defogger: Section
Defogger: Section
DEF
A
B
SECTION
DEFOGGER C
E
CONTENTS
BASIC INSPECTION .................................... 3 Component Function Check ....................................12 F
Diagnosis Procedure ...............................................12
DIAGNOSIS AND REPAIR WORKFLOW .......... 3 Component Inspection .............................................14
Repair Work Flow ...................................................... 3 G
DOOR MIRROR DEFOGGER LH ..................... 15
SYSTEM DESCRIPTION .............................. 5 Description ...............................................................15
Component Function Check ....................................15
REAR WINDOW DEFOGGER SYSTEM ............. 5 Diagnosis Procedure ...............................................15 H
System Diagram ........................................................ 5 Component Inspection (With Automatic Drive Po-
System Description ................................................... 5 sitioner) ....................................................................17
Component Parts Location ........................................ 6 Component Inspection (Without Automatic Drive I
Component Description ............................................. 6 Positioner) ...............................................................17
DIAGNOSIS SYSTEM (BCM) ............................. 7 DOOR MIRROR DEFOGGER RH ..................... 18
Description ...............................................................18 J
COMMON ITEM ........................................................... 7
Component Function Check ....................................18
COMMON ITEM : CONSULT Function (BCM -
Diagnosis Procedure ...............................................18
COMMON ITEM) ....................................................... 7
Component Inspection (With Automatic Drive Po- K
REAR WINDOW DEFOGGER ..................................... 7 sitioner) ....................................................................20
REAR WINDOW DEFOGGER : CONSULT Func- Component Inspection (Without Automatic Drive
tion (BCM - REAR DEFOGGER) .............................. 8 Positioner) ...............................................................20 DEF
DTC/CIRCUIT DIAGNOSIS .......................... 9 ECU DIAGNOSIS INFORMATION .............. 21
REAR WINDOW DEFOGGER SWITCH ............. 9 BCM (BODY CONTROL MODULE) ................. 21 M
Description ................................................................ 9 Reference Value ......................................................21
Component Function Check (2 Control Dial Sys- Terminal Layout .......................................................24
tem or Auto A/C) ....................................................... 9 Physical Values .......................................................24 N
Component Function Check (3 Control Dial Sys-
tem Without Auto A/C) .............................................. 9 WIRING DIAGRAM ...................................... 30
Diagnosis Procedure (2 Control Dial System or
REAR WINDOW DEFOGGER .......................... 30 O
Auto A/C) ................................................................... 9
Wiring Diagram ........................................................30
Diagnosis Procedure (3 Control Dial System With-
out Auto A/C) ........................................................... 10 SYMPTOM DIAGNOSIS .............................. 38
P
REAR WINDOW DEFOGGER RELAY ..............11 REAR WINDOW DEFOGGER SYSTEM
Description .............................................................. 11 SYMPTOMS ...................................................... 38
Component Function Check .................................... 11
Symptom Table .......................................................38
Diagnosis Procedure ............................................... 11
REAR WINDOW DEFOGGER AND DOOR
REAR WINDOW DEFOGGER SYSTEM ............12
MIRROR DEFOGGER DO NOT OPERATE. .... 39
Description .............................................................. 12
WORK FLOW
C
DEF
M
ABJIA0524GB
DETAILED FLOW
N
1. CUSTOMER INFORMATION
Talk to the customer to obtain detailed information about the symptom. O
>> GO TO 2
2. SYSTEM DESCRIPTION P
>> GO TO 3
3. SYMPTOM
Check for symptoms. Refer to DEF-38, "Symptom Table".
>> GO TO 4
4. MALFUNCTIONING PARTS
Repair or replace the applicable parts.
>> GO TO 5
5. SYSTEM CHECK
Operate rear window defogger switch to ensure that rear window defogger and heated mirrors operate.
Does the system operate normally?
YES >> Inspection End
NO >> Refer to GI-42, "Intermittent Incident".
AWLIA1915GB
H
System Description INFOID:0000000007946824
Operation Description
• When rear window defogger switch is turned ON while ignition switch is ON, the front air control (rear win- I
dow defogger switch) transmits rear window defogger switch signal to BCM.
• BCM transmits rear window defogger control signal to IPDM E/R and display unit via CAN communication
when rear window defogger operates. J
• IPDM E/R turns rear window defogger relay and heated mirror relay ON when rear window defogger switch
signal is received.
• Rear window defogger and door mirror defogger are supplied with power and operate when rear window
K
defogger relay and heated mirror relay turn ON.
• Rear window defogger ON is displayed when signal is received.
Timer function DEF
• BCM turns rear window defogger relay and heated mirror relay ON for approximately 15 minutes when rear
window defogger switch is turned ON while ignition switch is ON. It makes rear window defogger and door
mirror defogger operate.
• Timer is canceled after pressing rear window defogger switch again during timer operation. Then BCM turns M
rear window defogger relay and heated mirror relay OFF. The same reaction also occurs during timer opera-
tion, if the ignition switch is turned OFF.
N
INPUT/OUTPUT SIGNAL CHART
ALLIA0560ZZ
• Operates the rear window defogger with the operation of rear window defogger switch.
BCM
• Performs the timer control of rear window defogger.
Rear window defogger relay • Operates the rear window defogger with the control signal from BCM.
Front air control (rear window defogger • The rear window defogger switch is turned ON.
switch) • Turns the indicator lamp ON when detecting the operation of rear window defogger.
• Heats the heating wire with the power supply from the rear window defogger relay to pre-
Rear window defogger
vent the rear window from fogging up.
Heated mirror relay (if equipped) • Operates the door mirror defogger with the control signal from BCM.
• Heats the heating wire with the power supply from the heated mirror relay to prevent the
Door mirror defogger (if equipped)
door mirror from fogging up.
SYSTEM APPLICATION
G
BCM can perform the following functions.
Configuration
Work support
Data Monitor
Active Test
J
DATA MONITOR
ACTIVE TEST
I
Regarding Wiring Diagram information, refer to DEF-30, "Wiring Diagram".
J
1. CHECK FRONT AIR CONTROL (REAR WINDOW DEFOGGER SWITCH) CIRCUIT
Operate the rear window defogger switch.
K
Is the inspection result normal?
YES >> Inspection End.
NO >> GO TO 2
DEF
2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect BCM and front air control. M
3. Check continuity between BCM connector and front air control connector.
F
Regarding Wiring Diagram information, refer to DEF-30, "Wiring Diagram".
1. CHECK FUSES G
Check if any of the following fuses in the IPDM E/R are blown.
H
COMPONENT PARTS AMPERE FUSE NO.
IPDM E/R 15A 46
IPDM E/R 15A 47 I
Is the inspection result normal?
YES >> GO TO 2
NO >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. J
2. CHECK REAR WINDOW DEFOGGER RELAY POWER SUPPLY CIRCUIT
1. Turn ignition switch ON. K
2. Check voltage between IPDM E/R connector and ground.
Terminals DEF
Condition of rear
(+) Voltage (V)
window defogger
(–) (Approx.)
IPDM E/R con- switch
Terminal
nector M
ON Battery voltage
E124 60 Ground
OFF 0
LIIA2190E N
Is the inspection result normal?
YES >> GO TO 3
NO >> Replace IPDM E/R. Refer to PCS-28, "Removal and Installation of IPDM E/R".
O
3. CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to GI-42, "Intermittent Incident". P
Is the inspection result normal?
YES >> Check the following.
• Battery power supply circuit
• IPDM E/R
NO >> Repair or replace the malfunctioning parts.
Heats the heating wire with the power supply from the rear window defogger relay to prevent the rear window
from fogging up.
Component Function Check INFOID:0000000007946838
1. CHECK FUSES
Check if any of the following fuses in IPDM E/R are blown.
Terminals
Condition of rear
(+) Voltage (V)
window defogger
(–) (Approx.)
IPDM E/R con- switch
Terminal
nector
ON Battery voltage
E124 60 Ground
OFF 0
LIIA2190E
Is the inspection result normal?
YES >> GO TO 3
NO >> Replace IPDM E/R. Refer to PCS-28, "Removal and Installation of IPDM E/R".
3. CHECK REAR WINDOW DEFOGGER POWER CIRCUIT HARNESS CONTINUITY
Condition Continuity
12V direct current supply between G
Yes
terminals 1 and 2
No current supply No
Is the inspection result normal? H
YES >> GO TO 5
NO >> Replace rear window defogger cut-out relay. SEF145X
ALLIA0885ZZ
Terminals
(+) Condition of rear
Voltage (V)
window
Rear window (–) (Approx.)
defogger switch
defogger Terminal
ALLIA0177ZZ
connector
ON Battery voltage
B78 1 Ground
OFF 0
Is the inspection result normal?
YES >> GO TO 8
NO >> Repair or replace harness.
8. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear window defogger.
3. Check continuity between rear window defogger connector and
ground.
9. CHECK FILAMENT
Check filament.
Refer to DEF-14, "Component Inspection".
Is the inspection result normal?
YES >> Refer to GI-42, "Intermittent Incident".
NO >> Repair filament. Refer to DEF-46, "Filament Repair".
Component Inspection INFOID:0000000007946840
1. CHECK FILAMENT
Check the filament for damage or open circuits.
Refer to DEF-46, "Filament Check".
Is the inspection result normal?
YES >> Inspection End.
NO >> Repair filament. Refer to DEF-46, "Filament Repair".
Heats the heating wire with the power supply from the heated mirror relay to prevent the door mirror from fog- B
ging up.
Component Function Check INFOID:0000000007946842
C
1. CHECK DOOR MIRROR DEFOGGER LH
Check that heating wire of door mirror defogger LH is heated when turning the rear window defogger switch
ON. D
Is the inspection result normal?
YES >> Door mirror defogger is OK.
NO >> Refer to DEF-15, "Diagnosis Procedure". E
LIIA1454E
ALLIA0888ZZ
D
1. CHECK DOOR MIRROR DEFOGGER
Check continuity between door mirror LH terminals 10 and 11.
E
10 - 11 : Continuity should exist.
Is the inspection result normal?
YES >> Check the condition of the harness and the connector. F
NO >> Replace malfunctioning door mirror LH. Refer to MIR-
15, "Door Mirror Assembly".
G
AWLIA1209ZZ
H
Component Inspection (Without Automatic Drive Positioner) INFOID:0000000007946845
DEF
ALLIA0889ZZ
Heats the heating wire with the power supply from the heated mirror relay to prevent the door mirror from fog-
ging up.
Component Function Check INFOID:0000000007946847
LIIA1454E
Terminal I
Voltage (V)
Connector Condition
(+) (-) (Approx.)
ALLIA0888ZZ
AWLIA1209ZZ
ALLIA0889ZZ
DEF
LIIA2443E
C
Combination switch in- Lighting, turn, wiper OFF
2 SB Input ON
put 5 Wiper dial position 4
D
SKIA5291E
SKIA5292E G
H
Combination switch in- Lighting, turn, wiper OFF
4 Y Input ON
put 3 Wiper dial position 4
I
SKIA5291E
SKIA5292E
DEF
Brake pedal depressed Battery voltage
9 R/G Brake switch Input ON
Brake pedal released 0V
Ignition switch (ACC or ACC or M
11 O Input Ignition switch ACC or ON Battery voltage
ON) ON
Front door switch RH
(All)
ON (open) 0V N
Rear door switch lower
12 R/L Input OFF
RH (King Cab)
Rear door switch up-
OFF (closed) Battery voltage O
per RH (King Cab)
LIIA1893E
LIIA1895E
PIIA2344E
SKIA5291E
D
F
SKIA5292E
G
Combination switch Lighting, turn, wiper OFF
34 L Output ON
output 3 Wiper dial position 4
H
SKIA5291E
Combination switch I
35 O/B
output 2
SKIA5292E K
Key switch and key Key inserted Battery voltage
37 B/R Input OFF
lock solenoid Key removed 0V
DEF
38 W/L Ignition switch (ON) Input ON — Battery voltage
39 L CAN-H — — — —
40 P CAN-L — — — — M
Rear defogger switch ON 0V
41 Y/B Rear defogger switch Input ON
Rear defogger switch OFF 5V
Front door switch LH N
(All)
ON (open) 0V
Rear door switch lower
47 SB Input OFF
LH (King Cab) O
Rear door switch up-
OFF (closed) Battery voltage
per LH (King Cab)
SKIA3009J
SKIA3009J
SKIA3009J
SKIA3009J
DEF
ABLWA1926GB
DEF
ABLIA4180GB
ABLIA4181GB
DEF
ABLIA4182GB
ABLIA4183GB
DEF
ABLIA4184GB
ABLIA4185GB
DEF
ABLIA4186GB
Both door mirror defoggers do not operate but rear window 1. Door mirror defogger power supply circuit check DEF-41
defogger operates. (with heated mirrors) 2. Replace IPDM E/R PCS-28
Door mirror LH defogger does not operate. (with heated
1. Door mirror LH defogger circuit check DEF-42
mirrors)
Door mirror RH defogger does not operate. (with heated
1. Door mirror RH defogger circuit check DEF-43
mirrors)
Rear window defogger switch does not light, and rear win-
dow defogger is not shown on the display, but rear window 1. Replace front air control VTL-8
defogger operates.
DEF
DEF
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. D
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING: E
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
F
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this G
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS H
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a I
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the J
battery, and wait at least 3 minutes before performing any service.
Handling for Adhesive and Primer INFOID:0000000007946863
K
• Do not use an adhesive which is past its usable date. Shelf life of this product is limited to six months after
the date of manufacture. Carefully adhere to the expiration or manufacture date printed on the box.
• Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
• Open the seal of the primer and adhesive just before application. Discard the remainder. DEF
• Before application, be sure to shake the primer container to stir the contents. If any floating material is found,
do not use it.
• If any primer or adhesive contacts the skin, wipe it off with gasoline or equivalent and wash the skin with M
soap.
• When using primer and adhesive, always observe the precautions in the instruction manual.
N
1. When measuring voltage, wrap tin foil around the top of the neg-
ative probe.Then press the foil against the wire with your finger.
SEL122R
SEL263
SEL265
REPAIR EQUIPMENT
• Conductive silver composition (DuPont No. 4817 or equivalent)
• Ruler 30 cm (11.8 in) long
Revision: October 2012 DEF-46 2013 Titan
REAR WINDOW DEFOGGER
< REMOVAL AND INSTALLATION >
• Drawing pen
• Heat gun A
• Alcohol
• Cloth
REPAIRING PROCEDURE B
1. Wipe broken heat wire and its surrounding area clean with a
cloth dampened in alcohol.
2. Apply a small amount of conductive silver composition to tip of C
drawing pen.
NOTE:
Shake silver composition container before use. D
3. Place ruler on glass along broken line. Deposit conductive silver
composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm (0.20 in)] of the break. E
PIIA0215E
4. After repair has been completed, check repaired wire for conti- F
nuity. This check should be conducted 10 minutes after silver
composition is deposited.
CAUTION: G
Do not touch repaired area while test is being conducted.
I
SEL012D
SEL013D
M