Plate Steel Catalogue

2004-2005
Plate Steel
Specification
Guide
International Steel Group, Inc.

Burns Harbor, Coatesville and Conshohocken
CAPABILITIES OVERVIEW
PLATE TYPES HEAT TREATMENT
Carbon & HSLA Normalizing and Normalize and Temper
Alloy – Quench & Temper
Commercial Grades, Military Armor, Annealing and Spherodize Anneal
Aircraft Quality, Tool Steel Stress Relieving
Clad Steel Special Non-Standard Cycles
Duracorr® (12% Chromium Stainless)
Plate Coils TESTING
Floor Plate CVN Impacts, Drop Weight
Through Gauge Testing, Dynamic Tear
RANGE – MOST COMPLETE SIZE RANGE HIC Testing (Hydrogen Induced Cracking)
Thickness Cleanliness (Aircraft Quality)
Carbon/HSLA – 3/16" to 30"
Ultrasonic Testing
Alloy – .125" to 15"
Magnetic Particle Testing
Widths – up to 195" wide
Lengths – up to 1525" and longer QUICK PLATE PROGRAM
Pattern weights – up to 100,000 lbs. Burns Harbor, IN
Refer to size charts in back of Steel Specification Guide Coatesville and Conshohocken, PA
See Daily Inventory Listings
MULTIPLE PRODUCING LOCATIONS
Burns Harbor, IN PLATE COILS
Coatesville, PA 84" to 96" Wide
Conshohocken, PA 3/16" to 5/8" Thick
Carbon and HSLA
MELTING FACILITIES
Sparrows Point, MD and Burns Harbor, IN THERMAL CUTTING
Blast Furnaces/Basic Oxygen Furnaces Oxy-fuel and Plasma
10" Strand Cast Slabs Circles, Rings, Sketches, Strips
Coatesville, PA SPECIAL PLATE AND FLAMECUT TOLERANCES

Electric Furnace Melting Thickness
9" Strand Cast Slabs and Ingot (bottom poured) Casting Width and Length
Ladle Refining/Low Sulfur Shape Control Camber
Vacuum Degassing Flatness
VOD Unit – Duracorr® Stainless Melting
SURFACE PREPARATION
ROLLING MILLS Blasting
Burns Harbor, IN – 3/16" to 4", up to 150" wide Painting – See Handout on Hempel ZS 15890
TMCP (Thermal-Mechanical Controlled Processing) Oiling
Precise Weight Plate
Coatesville, PA – 7/16" to 30", up to 195" wide MILL EDGE
Conshohocken, PA – Improved Customer Yields
.125" to 1" Alloy and
.1875" to 2" carbon, up to 100" wide ISO 9001-2000 CERTIFIED
Discrete and Coil
The Plate Professionals

TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ASTM Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–26
Aircraft Quality Steels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
American Bureau of Shipping Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-29
American Petroleum Institute Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-31
ASTM Chemistry Only Steels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32–34
ISG Plate Grades:
Free Machining Steels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Proprietary Grades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35-38
Military Alloy Steels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Abrasion Resistant T-1® Steels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40–41
Premium Abrasion Resistant Steels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Abrasion Resistant Steels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Mold, Tool & Die Steels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Tool Steels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Weathering Steels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
AASHTO Bridge Steel Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Cross Reference of Popular International Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Coatesville and Conshohocken Size Cards
Burns Harbor Size Cards
Physical Properties of Steel
Available Product Brochures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inside Back Cover
ISG PLATE CARBON AND ALLOY PLATE STEELS

conforming to ASTM A6 or A20
INTRODUCTION
This brochure briefly outlines the specified chemistry and mechanical properties of some commonly used plate
steels. The information presented here is based on the 2004 ASTM Specifications and ISG Plates’ practices.
This is not intended to be a complete guide. For example, some grades are available in heavier thicknesses or
with improved properties for specialized applications. Other types of heat treatment may also be available to
enhance the properties of the plate. ASTM A6 and A20 also specify additional requirements.
PLATE DIMENSIONS AVAILABLE FROM ISG PLATE*

(See Size Cards)
Carbon Alloy
Length 1525 in. 1030 in.
Width 195 in. 195 in.
Thickness 30 in. 15 in.
Heat Treated Length** 600 in. 600 in.
* All dimensions listed are approximate maximums. Actual plate sizes available depend on the combination of length, width and thickness as well
as material specification. Dimensions and specifications exceeding those listed may be available. For specific information, contact ISG Plate.
** Refer for acceptance normalized lengths up to 875".
ABBREVIATIONS USED IN THIS GUIDE

CT Calcium Treated N&T Normalize and Temper
C/G/P Coarse Grain Practice PHT Precipitation Heat Treatment
EF-VIP Electric Furnace Quality-Vacuum Improved Plate Q&T Quench and Temper
F/G/P Fine Grain Practice TMCP Thermo-Mechanical Controlled Process
LCVN Longitudinal Charpy-V-Notch Impact Test TCVN Transverse Charpy-V-Notch Impact Test
N Normalize
For more information or assistance regarding your plate steel needs, contact ISG Plate at 800-966-5352
or email Plate.Professionals@intlsteel.com
2
ASTM SPECIFICATIONS
SPECIFICATION A36 A36 A36 A36 A36 A131*

Type of Steel Carbon Carbon Carbon Carbon Carbon -
Requirements for Delivery A6 A6 A6 A6 A6 -
Tensile Strength (ksi) 58/80 58/80 58/80 58/80 58/80 -
Yield Strength (Min. ksi) 36 YP 36 YP 36 YP 36 YP 36 YP over -
(Yield Point if 4-8" incl.;
designated YP) 32 over 8"
3
Spec. Thickness (Max. in.) /4 > 3/4 to 11/2 > 11/2 to 2 1/2 > 21/2 to 4 over 4 -
ISG Plate
3
Thickness (Max. in.) /4 > 3/4 to 11/2 > 11/2 to 2 1/2 > 21/2 to 4 18 -
Chemical Composition (%) Unless a range is specified, individual values are maximums
Carbon .25 .25 .26 .27 .29 -
Manganese - .80/1.20** .80/1.20** .85/1.20** .85/1.20** -
Phosphorus .04 .04 .04 .04 .04 -
Sulfur .05 .05 .05 .05 .05 -
Silicon .40 .40 .15/.40 .15/.40 .15/.40 -
Chromium - - - - - -
Nickel - - - - - -
Molybdenum - - - - - -
Copper .20 Min. .20 Min. .20 Min. .20 Min. .20 Min. -
when when when when when
specified specified specified specified specified
Other Elements - - - - - -
Heat Treatment Required - - - - - -
* A131 Grades are similar to ABS Grades shown on page 28-29.
** For each reduction of 0.01% below the carbon maximum, an increase of 0.06% manganese above the specified maximum is
permitted, up to 1.35%.
3
CON TINUED ASTM SPECIFICATIONS
A202 A202 A203 A203 A203 A203

SPECIFICATION Grade A Grade B Grade A Grade B Grade D Grade E
Type of Steel Alloy Alloy Alloy Alloy Alloy Alloy
Requirements for Delivery A20 A20 A20 A20 A20 A20
Tensile Strength (ksi) 75/95 85/110 65/85 70/90 65/85 70/90
Yield Strength (Min. ksi) 45 47 37 40 37 40
(Yield Point if
designated YP)
Spec. Thickness (Max. in.) - - - - - -
ISG Plate
Thickness (Max. in.) 2 2 6 6 4 4
Carbon .17 .25 .17 to 2" .21 to 2" .17 to 2" .20 to 2"
incl.; .20 incl.; .24 incl.; .20 incl.; .23
over 2-4" over 2-4" over 2-4" over 2-4"
incl.; .23 incl.; .25 incl. incl.
over 4-6" over 4-6"
incl. incl.
Manganese 1.05/1.40 1.05/1.40 .70 .70 .70 .70
to 2" incl.; to 2" incl.; to 2" incl.; to 2" incl.;
.80 .80 .80 .80
incl. incl. incl. incl.
Phosphorus .035 .035 .035 .035 .035 .035
Sulfur .035 .035 .035 .035 .035 .035
Silicon .60/.90 .60/.90 .15/.40 .15/.40 .15/.40 .15/.40
Chromium .35/.60 .35/.60 ■ ■ ■ ■
Nickel ■ ■ 2.10/2.50 2.10/2.50 3.25/3.75 3.25/3.75

Molybdenum ■ ■ ■ ■ ■ ■
Copper ■ ■ ■ ■ ■ ■
Other Elements - - F/G/P F/G/P F/G/P F/G/P

Heat Treatment Required - - N N N N
■ Restricted to ASTM A20 limits for unspecified elements.
4
A203 A204 A204 A204 A225† A225†

SPECIFICATION Grade F Grade A Grade B Grade C Grade C Grade D
Tensile Strength (ksi) 80/100 to 2" 65/85 70/90 75/95 105/135 80/105 to
incl.; 75/95 3" incl.;
over 2" 75/100
over 3"
Yield Strength (Min. ksi) 55 to 2" 37 40 43 70 60 to 3"
(Yield Point if incl.; 50 incl.; 55
designated YP) over 2" over 3"
ISG Plate
Thickness (Max. in.) 4 6 6 4 .58 6
Carbon .20 to 2" .18 to 1" .20 to 1" .23 to 1" .25 .20
incl. incl.; .23 incl.; .25 incl.; .28
over 2-4" over 2-4" over 2-4"
incl.; .25 incl.; .27 incl.
over 4-6" over 4-6"
incl. incl.
Manganese .70 .90 .90 .90 1.60 1.70
to 2" incl.;
.80
over 2-4"
incl.
Phosphorus .035 .035 .035 .035 .035 .035
Sulfur .035 .035 .035 .035 .035 .035
Silicon .15/.40 .15/.40 .15/.40 .15/.40 .15/.40 .10/.50
Chromium ■ ■ ■ ■ ■ ■
Nickel 3.25/3.75 ■ ■ ■ .40/.70 .40/.70

Molybdenum ■ .45/.60 .45/.60 .45/.60 ■ ■
Copper ■ ■ ■ ■ ■ ■
Other Elements F/G/P - - - .13/.18V .10/.18V

Heat Treatment Required Q&T N over N over N over N over 2" ISG N
11/2"* 11/2"* 11/2"* Plate req. N
all thicknesses
* ISG Plate requires N ≥ 5/16".
† Post-weld heat treatment may degrade heat-affected zone strength and toughness. Pretesting of specific welding and post-weld
heat treating procedures is recommended to assure optimization of final property levels.
5
A242†▲ A283 A283 A283 A283

SPECIFICATION Type 1** Grade A Grade B Grade C Grade D
Type of Steel Carbon Carbon Carbon Carbon Carbon
Requirements for Delivery A6 A6 A6 A6 A6
Tensile Strength (ksi) 70 Min. 45/60 50/65 55/75 60/80
to 3/4" incl.;
67 Min. over
3
/4 -11/2" incl.;
63 Min. over 11/2"
Yield Strength (Min. ksi) 50 YP to 24 YP 27 YP 30 YP 33 YP
3
(Yield Point if /4" incl.; 46
designated YP) over 3/4-11/2"
incl.; 42
over 11/2"
Spec. Thickness (Max. in.) 4 - - - -
ISG Plate
Thickness (Max. in.) 8 16 16 16 16
Carbon .15 .14 .17 .24 .27
Manganese 1.00 .90 .90 .90 .90
Phosphorus .15* .035 .035 .035 .035
Sulfur .05 .04 .04 .04 .04
Silicon - .40 to 1.5" incl.; .40 to 1.5" incl.; .40 to 1.5" incl.; .40 to 1.5" incl.;
.15/.40 over 1.5" .15/.40 over 1.5" .15/.40 over 1.5" .15/.40 over 1.5"
Chromium - - - - -
Nickel - - - - -
Molybdenum - - - - -
Copper .20 Min. .20 Min. .20 Min. .20 Min. .20 Min.
when when when when
specified specified specified specified
Other Elements - - - - -
Heat Treatment Required - - - - -
* Coatesville produces to .04 Max. Phosphorus.

** ASTM G101 corrosion index minimum must also be met.
▲ Also produced as Mayari-R.®
6
A285 A285 A285 A299 A299 A302 A302

SPECIFICATION Grade A Grade B Grade C Grade A Grade B Grade A Grade B
Type of Steel Carbon Carbon Carbon Carbon Carbon Alloy Alloy
Requirements for Delivery A20 A20 A20 A20 A20 A20 A20
Tensile Strength (ksi) 45/65 50/70 55/75 75/95 80/100 75/95 80/100
Yield Strength (Min. ksi) 24 27 30 42 to 1" 47 to 1" 45 50
designated YP) over 1" over 1"
Spec. Thickness (Max. in.) 2 2 2 - - - -
ISG Plate
Thickness (Max. in.) 2 2 2 8 8 6 6
Carbon .17 .22 .28 .26 to 1" .28 to 1" .20 to 1" .20 to 1"
over 1" over 1" over 1-2" over 1-2"
incl.; .25 incl.; .25
over 2" over 2"
Manganese .90 .90 .90 .90/1.40 to .90/1.40 to .95/1.30 1.15/1.50
1" incl.; 1" incl.;
.90/1.50 .90/1.50
over 1" over 1"
Phosphorus .035 .035 .035 .035 .035 .035 .035
Sulfur .035 .035 .035 .035 .035 .035 .035
Silicon ■ ■ ■ .15/.40 .15/.40 .15/.40 .15/.40
Chromium ■ ■ ■ ■ ■ ■ ■
Nickel ■ ■ ■ ■ ■ ■ ■
Molybdenum ■ ■ ■ ■ ■ .45/.60 .45/.60

Copper Either Either Either - - -
.20/.35 .20/.35 .20/.35
or .25 or .25 or .25
when when when
specified specified specified
Other Elements - - - F/G/P F/G/P F/G/P F/G/P
Heat Treatment Required - - - N over 2" N over 2" N over 2"* N over 2"*
* ISG Plate requires N 1" and under.
7
A387*** A387 A387 A387 A387

A302 A302 Grade 11 Grade 12 Grade 21 Grade 21L Grade 22
SPECIFICATION Grade C Grade D A353 Class 1 Class 1 Class 1 Class 1 Class 1
Type of Steel Alloy Alloy Alloy Alloy Alloy Alloy Alloy Alloy
Requirements for Delivery A20 A20 A20 A20 A20 A20 A20 A20
Tensile Strength (ksi) 80/100 80/100 100/120 60/85 55/80 60/85 60/85 60/85
Yield Strength (Min. ksi) 50 50 75 35 33 30 30 30
(Yield Point if
designated YP)
Spec. Thickness (Max. in.) - - - - - - - -
ISG Plate
Thickness (Max. in.) 10 12 11/2** 6** 12** 12** 12** 12**
Carbon .20 to 1" .20 to 1" .13 .05/.17 .05/.17 .05/.15 .10 .05/.15
incl.; .23 incl.; .23
over 1-2" over 1-2"
incl.; .25 incl.; .25
over 2" over 2"
Manganese 1.15/1.50 1.15/1.50 .90 .40/.65 .40/.65 .30/.60 .30/.60 .30/.60
Phosphorus .035 .035 .035 .035 .035 .035 .035 .035
Sulfur .035 .035 .035 .035 .035 .035 .035 .035
Silicon .15/.40 .15/.40 .15/.40 .50/.80 .15/.40 .50 .50 .50
Chromium ■ ■ ■ 1.00/1.50 .80/1.15 2.75/3.25 2.75/3.25 2.00/2.50
Nickel .40/.70 .70/1.00 8.50/9.50 ■ ■ ■ ■ ■
Molybdenum .45/.60 .45/.60 ■ .45/.65 .45/.60 .90/1.10 .90/1.10 .90/1.10

Copper ■ ■ ■ ■ ■ ■ ■ ■
Other Elements F/G/P F/G/P Mandatory - - - - -

TCVN
Heat Treatment Required N over 2"* N over 2"* NN&T Annealed Annealed Annealed Annealed Annealed
or N&T or N&T or N&T or N&T or N&T
* ISG Plate requires N 1" and under.
** Consult ISG Plate for plates over thickness listed.
*** Consult ISG Plate for other A387 Grades not shown.
A387 Brochure
8
A387** A387 A387 A387 A387 A387 A387 A387

Grade 22L Grade 5 Grade 9 Grade 11 Grade 12 Grade 21 Grade 22 Grade 5
SPECIFICATION Class 1 Class 1 Class 1 Class 2 Class 2 Class 2 Class 2 Class 2
Type of Steel Alloy Alloy Alloy Alloy Alloy Alloy Alloy Alloy
Tensile Strength (ksi) 60/85 60/85 60/85 75/100 65/85 75/100 75/100 75/100
Yield Strength (Min. ksi) 30 30 30 45 40 45 45 45
(Yield Point if
designated YP)
Spec. Thickness (Max. in.) - - - - - - - -
ISG Plate
Thickness (Max. in.) 12* 6* 6* 6* 6* 12* 12* 6*
Carbon .10 .15 .15 .05/.17 .05/.17 .05/.15 .05/.15 .15
Manganese .30/.60 .30/.60 .30/.60 .40/.65 .40/.65 .30/.60 .30/.60 .30/.60
Phosphorus .035 .035 .030 .035 .035 .035 .035 .035
Sulfur .035 .030 .030 .035 .035 .035 .035 .030
Silicon .50 .50 1.00 .50/.80 .15/.40 .50 .50 .50
Chromium 2.00/2.50 4.00/6.00 8.00/10.00 1.00/1.50 .80/1.15 2.75/3.25 2.00/2.50 4.00/6.00
Nickel ■ ■ ■ ■ ■ ■ ■ ■
Molybdenum .90/1.10 .45/.65 .90/1.10 .45/.65 .45/.60 .90/1.10 .90/1.10 .45/.65

Copper ■ ■ ■ ■ ■ ■ ■ ■
Other Elements - - - - - - - -
Heat Treatment Required Annealed Annealed Annealed N&T N&T N&T N&T N&T
or N&T or N&T or N&T
* Consult ISG Plate for plates over thickness listed.
** Consult ISG Plate for other A387 grades not listed.
A387 Brochure
9
A387 A387
Grade 9 Grade 91 A514† A514* A514† A514* A514*
SPECIFICATION Class 2 Class 2 A455 Grade A Grade B Grade E Grade F Grade H
Type of Steel Alloy Alloy Carbon Alloy Alloy Alloy Alloy Alloy
Tensile Strength (ksi) 75/100 85/110 75/95 to 110/130 110/130 110/130 110/130 110/130
.375" incl.; to 21/2" incl.;
73/93 over 100/130
.375-.580" over 21/2-
incl.; 70/90 6" incl.
over .580-
.750" incl.
Yield Strength (Min. ksi) 45 60 38 to .375" 100 100 100 to 100 100
(Yield Point if incl.;37 over 2 1/2" incl.;
designated YP) .375-.580" 90 over
incl.; 35 2 1/2 -6"
over .580- incl.
.750" incl.
3
Spec. Thickness (Max. in.) - - /4 11/4 11/4 6 2 1/2 2
ISG Plate
3
Thickness (Max. in.) 6* 6* /4 11/4 11/4 6 2 1/2 2
Carbon .15 .08/.12 .33** .15/.21 .12/.21 .12/.20 .10/.20 .12/.21
Manganese .30/.60 .30/.60 .85/1.20 .80/1.10 .70/1.00 .40/.70 .60/1.00 .95/1.30
Phosphorus .030 .020 .035 .035 .035 .035 .035 .035
Sulfur .030 .010 .035 .035 .035 .035 .035 .035
Silicon 1.00 .20/.50 .10** .40/.80 .20/.35 .20/.40 .15/.35 .20/.35
Chromium 8.00/10.00 8.00/9.50 ■ .50/.80 .40/.65 1.40/2.00 .40/.65 .40/.65
Nickel ■ .40 ■ - - - .70/1.00 .30/.70
Molybdenum .90/1.10 .85/1.05 ■ .18/.28 .15/.25 .40/.60 .40/.60 .20/.30
Copper ■ ■ ■ - - - .15/.50 -
Other Elements - .18/.25 V - .05/.15 Zr .03/.08 V .01/.10 Ti .03/.08 V .03/.08 V
.06/.10 Cb (or Ce) .01/.03 Ti .001/.005 B .0005/.006 B .0005/.005 B
.030/.070 N .0025 .0005/.005 B
.04 Al B
Heat Treatment Required N&T N&T - Q&T Q&T Q&T Q&T Q&T
* It is important to note that this grade of steel may be susceptible to cracking in the heat-affected zone of welds during post-weld
heat treatment (stress relief). Therefore, ISG Plate recommends that careful consideration be given to this phenomenon by
competent welding engineers before stress relieving is applied to weldments of this grade. Also, it is not recommended for
service at temperatures lower than -50˚F or higher than 800˚F.
** At the producer's option, silicon may be .40 Max. When silicon is .10 min., the carbon shall be .28 Max.
A387 Brochure
A514 Brochure
10
A514† A514* A515 A515 A515 A516

SPECIFICATION Grade P Grade Q Grade 60 Grade 65 Grade 70 Grade 55
Type of Steel Alloy Alloy Carbon Carbon Carbon Carbon
Tensile Strength (ksi) 110/130 to 110/130 to 60/80 65/85 70/90 55/75
2 1/2" incl.; 2 1/2" incl.;
100/130 100/130
over 2 1/2 - over 2 1/2 -
6" incl. 6" incl.
Yield Strength (Min. ksi) 100 to 100 to 32 35 38 30
(Yield Strength 21/2" incl.; 21/2" incl.;
designated YP) 90 over 90 over
2 1/2 -6" incl. 2 1/2 -6" incl.
Spec. Thickness (Max. in.) 6 6 - - - -
ISG Plate
Thickness (Max. in.) 4 8 15 15 15 15
Carbon .12/.21 .14/.21 .24 to 1" .28 to 1" .31 to 1" .18 to 1/2" incl.;
incl.; .27 incl.; .31 incl.; .33 .20 over 1/2 -2"
over 1-2" over 1-2" over 1-2" incl.; .22 over
incl.; .29 incl.; .33 incl.; .35 2-4" incl.; .24
over 2-4" over 2" over 2" over 4-8" incl.;
incl.; .31 .26 over 8"
over 4"
Manganese .45 /.70 .95/1.30 .90 .90 1.20 .60/.90 to 1/2"
incl.; .60/1.20
over 1/2"
Phosphorus .035 .035 .035 .035 .035 .035
Sulfur .035 .035 .035 .035 .035 .035
Silicon .20/.35 .15/.35 .15/.40 .15/.40 .15/.40 .15/.40
Chromium .85/1.20 1.00/1.50 ■ ■ ■ ■
Nickel 1.20/1.50 1.20/1.50 ■ ■ ■ ■
Molybdenum .45/.60 .40/.60 ■ ■ ■ ■
Copper - - ■ ■ ■ ■
Other Elements .001/.005 B .03/.08 V C/G/P C/G/P C/G/P F/G/P

Heat Treatment Required Q&T Q&T N over 2" N over 2" N over 2" N over
11/2" or when
Impact Tests
required**
** Unless otherwise specified by the purchaser and approved by ISG Plate.
A514 Brochure
11
A516 A516 A516 A517† A517* A517† A517*

SPECIFICATION Grade 60 Grade 65 Grade 70 Grade A Grade B Grade E Grade F
Type of Steel Carbon Carbon Carbon Alloy Alloy Alloy Alloy
Tensile Strength (ksi) 60/80 65/85 70/90 115/135 115/135 115/135 to 115/135
2 1/2" incl.;
105/135
over 2 1/2 -
6" incl.
Yield Strength (Min. ksi) 32 35 38 100 100 100 to 2 1/2" 100
(Yield Point if incl.; 90 over
designated YP) 2 1/2 -6" incl.
Spec. Thickness (Max. in.) - - - 11/4 11/4 6 2 1/2
ISG Plate
Thickness (Max. in.) 15 15 15 11/4 11/4 6 2 1/2
Carbon .21 to 1/2" .24 to 1/2" .27 to 1/2" .15/.21 .15/.21 .12/.20 .10/.20
incl.; .23 incl.; .26 incl.; .28
over 1/2 -2" over 1/2 -2" over 1/2 -2"
incl.; .25 incl.; .28 incl.; .30
over 2-4" over 2-4" over 2-4"
incl.; .27 incl.; .29 incl.; .31
over 4" over 4" over 4"
Manganese .60/.90 to .85/1.20 .85/1.20 .80/1.10 .70/1.00 .40/.70 .60/1.00
to 1/2" incl.;
.85/1.20
over 1/2"
Phosphorus .035 .035 .035 .035 .035 .035 .035
Sulfur .035 .035 .035 .035 .035 .035 .035
Silicon .15/.40 .15/.40 .15/.40 .40/.80 .15/.35 .10/.40 .15/.35
Chromium ■ ■ ■ .50/.80 .40/.65 1.40/2.00 .40/.65
Nickel ■ ■ ■ ■ ■ ■ .70/1.00
Molybdenum ■ ■ ■ .18/.28 .15/.25 .40/.60 .40/.60
Copper ■ ■ ■ ■ ■ ■ .15/.50
Other Elements F/G/P F/G/P F/G/P .0025 .03/.08 V .01/.10 Ti .0005/.006
B .05/.15 .0005/.005 .001/.005 B B .03/.08 V
Zr (or Ce) B .01/.03 Ti
Heat Treatment Required N over N over N over Q&T Q&T Q&T Q&T
11/2" or when 11/2" or when 11/2" or when
Impact Tests Impact Tests Impact Tests TCVN TCVN TCVN TCVN
required** required** required**
** Unless otherwise specified by the purchaser and approved by ISG Plate.
12
A533 A533
A517* A517† A517* A529 A529 Type A Type B
SPECIFICATION Grade H Grade P Grade Q Grade 50 Grade 55 Class 1 Class 1
Type of Steel Alloy Alloy Alloy Carbon Carbon Alloy Alloy
Tensile Strength (ksi) 115/135 115/135 to 115/135 to 70/100 70/100 80/100 80/100
2 1/2" incl.; 2 1/2" incl.;
105/135 105/135
over 2 1/2 - over 2 1/2 -
3.33" incl. 6" incl.
Yield Strength (Min. ksi) 100 100 to 2 1/2" 100 to 50 55 50 50
(Yield Point if incl.; 90 2 1/2" incl.;
designated YP) over 2 1/2 - 90 over
3.33" incl. 2 1/2 -6" incl.
Spec. Thickness (Max. in.) 2 4 6 1 1 - -
ISG Plate
Thickness (Max. in.) 2 3.33 8 1 1 6 12
Carbon .12/.21 .12/.21 .14/.21 .27 .27 .25 .25
Manganese .95/1.30 .45/.70 .95/1.30 1.35** 1.35** 1.15/1.50 1.15/1.50
Phosphorus .035 .035 .035 .040 .040 .035 .035
Sulfur .035 .035 .035 .050 .050 .035 .035
Silicon .15/.35 .20/.35 .15/.35 .40 .40 .15/.40 .15/.40
Chromium .40/.65 .85/1.20 1.00/1.50 - - ■ ■
Nickel .30/.70 1.20/1.50 1.20/1.50 - - ■ .40/.70

Molybdenum .20/.30 .45/.60 .40/.60 - - .45/.60 .45/.60
Copper ■ ■ ■ .20 Min. .20 Min. ■ ■
when when
specified specified
Other Elements .0005 Min. B .001/.005 B .03/.08 V - - F/G/P F/G/P
.03/.08 V
Heat Treatment Required Q&T Q&T Q&T - - Q&T Q&T
TCVN TCVN TCVN
** Mn of 1.50 Max. is permitted with reduction of C Max. of 0.01% for each 0.05% increase in Mn.
A516 Brochure
A517 Brochure
13
A533 A533 A533 A533 A533 A533 A533

Type C Type D Type A Type B Type C Type D Type A
SPECIFICATION Class 1 Class 1 Class 2 Class 2 Class 2 Class 2 Class 3
Type of Steel Alloy Alloy Alloy Alloy Alloy Alloy Alloy
Yield Strength (Min. ksi) 50 50 70 70 70 70 83
(Yield Point if
designated YP)
Spec. Thickness (Max. in.) - - - - - - 2 1/2
ISG Plate
Thickness (Max. in.) 12 6 6 8 10 6 2 1/2
Carbon .25 .25 .25 .25 .25 .25 .25
Manganese 1.15/1.50 1.15/1.50 1.15/1.50 1.15/1.50 1.15/1.50 1.15/1.50 1.15/1.50
Phosphorus .035 .035 .035 .035 .035 .035 .035
Sulfur .035 .035 .035 .035 .035 .035 .035
Silicon .15/.40 .15/.40 .15/.40 .15/.40 .15/.40 .15/.40 .15/.40
Chromium ■ ■ ■ ■ ■ ■ ■
Nickel .70/1.00 .20/.40 - .40/.70 .70/1.00 .20/.40 -

Molybdenum .45/.60 .45/.60 .45/.60 .45/.60 .45/.60 .45/.60 .45/.60
Copper ■ ■ ■ ■ ■ ■ ■
Other Elements F/G/P F/G/P F/G/P F/G/P F/G/P F/G/P F/G/P

Heat Treatment Required Q&T Q&T Q&T Q&T Q&T Q&T Q&T
14
A533 A533 A533 A542*

Type B Type C Type D A537** A537** A537** Type A
SPECIFICATION Class 3 Class 3 Class 3 Class 1▲ Class 2▲▲ Class 3 Class 1
Type of Steel Alloy Alloy Alloy Carbon Carbon Carbon Alloy
Tensile Strength (ksi) 100/125 100/125 100/125 70/90 to 80/100 to 80/100 to 105/125
2 1/2" incl.; 21/2" incl.; 21/2" incl.;
65/85 over 75/95 over 75/95 over
2 1/2 -4" incl. 2 1/2 -4" incl.; 2 1/2 -4" incl.;
70/90 over 70/90 over
4-6" incl. 4-6" incl.
Yield Strength (Min. ksi) 83 83 83 50 to 2 1/2" 60 to 2 1/2" 55 to 2 1/2" 85
(Yield Point if incl.; 45 incl.; 55 incl.; 50
designated YP) over 2 1/2 - over 2 1/2 - over 2 1/2 -
4" incl. 4" incl.; 4" incl.;
46 over 40 over
4-6" incl. 4-6" incl.
Spec. Thickness (Max. in.) 2 1/2 2 1/2 2 1/2 4 6 6 -
ISG Plate
Thickness (Max. in.) 2 1/2 2 1/2 2 1/2 4 6 6 8
Carbon .25 .25 .25 .24 .24 .24 .15
Manganese 1.15/1.50 1.15/1.50 1.15/1.50 .70/1.35 to .70/1.35 to .70/1.35 to .30/.60
11/2" incl.; 11/2" incl.; 11/2" incl.;
1.00/1.60 1.00/1.60 1.00/1.60
over 11/2" over 11/2" over 11/2"
Phosphorus .035 .035 .035 .035 .035 .035 .025
Sulfur .035 .035 .035 .035 .035 .035 .025
Silicon .15/.40 .15/.40 .15/.40 .15/.50 .15/.50 .15/.50 .50
Chromium ■ ■ ■ .25 .25 .25 2.00/2.50
Nickel .40/.70 .70/1.00 .20/.40 .25 .25 .25 .40
Molybdenum .45/.60 .45/.60 .45/.60 .08 .08 .08 .90/1.10
Copper ■ ■ ■ .35 .35 .35 .40
Other Elements F/G/P F/G/P F/G/P F/G/P F/G/P F/G/P .03 V
Heat Treatment Required Q&T Q&T Q&T N Q&T Q&T Q&T,
QQ&T
or NQ&T
over 4"
* Consult ISG Plate for other A542 Types not shown.
▲ Also produced as RQC-60 (N).
▲▲ Also produced as RQC-60 (Q&T).
** When CE = C + Mn + Cr + Mo + V + Ni + Cu is 0.57 or less, manganese maximum is 1.60% and Nickel maximum is 0.50%.
6 5 15
15
A542 A542 A542 A542 A542 A542 A542

Type B Type C Type A Type B Type C Type A Type B
SPECIFICATION Class 1 Class 1 Class 2 Class 2 Class 2 Class 3 Class 3
(Yield Point if
designated YP)
Spec. Thickness (Max. in.) - - - - - - -
ISG Plate
Carbon .11/.15 .10/.15 .15 .11/.15 .10/.15 .15 .11/.15
Manganese .30/.60 .30/.60 .30/.60 .30/.60 .30/.60 .30/.60 .30/.60
Phosphorus .015 .025 .025 .015 .025 .025 .015
Sulfur .015 .025 .025 .015 .025 .025 .015
Silicon .50 .13 .50 .50 .13 .50 .50
Chromium 2.00/2.50 2.75/3.25 2.00/2.50 2.00/2.50 2.75/3.25 2.00/2.50 2.00/2.50
Nickel .25 .25 .40 .25 .25 .40 .25
Molybdenum .90/1.10 .90/1.10 .90/1.10 .90/1.10 .90/1.10 .90/1.10 .90/1.10
Copper .25 .25 .40 .25 .25 .40 .25
Other Elements .02 V .20/.30 V .03 V .02 V .20/.30 V .03 V .02 V
.015/.035 Ti .015/.035 Ti
.001/.003 B .001/.003 B
Heat Treatment Required Q&T, Q&T, Q&T, Q&T, Q&T, Q&T, Q&T,
QQ&T QQ&T QQ&T QQ&T QQ&T QQ&T QQ&T
or NQ&T or NQ&T or NQ&T or NQ&T or NQ&T or NQ&T or NQ&T
over 4" over 4" over 4" over 4" over 4" over 4" over 4"
16
A542 A542 A542 A542 A542 A542 A542

Type C Type A Type B Type C Type A Type B Type C
SPECIFICATION Class 3 Class 4 Class 4 Class 4 Class 4a Class 4a Class 4a
(Yield Point if
designated YP)
ISG Plate
Carbon .10/.15 .15 .11/.15 .10/.15 .15 .11/.15 .10/.15
Manganese .30/.60 .30/.60 .30/.60 .30/.60 .30/.60 .30/.60 .30/.60
Phosphorus .025 .025 .015 .025 .025 .015 .025
Sulfur .025 .025 .015 .025 .025 .015 .025
Silicon .13 .50 .50 .13 .50 .50 .13
Chromium 2.75/3.25 2.00/2.50 2.00/2.50 2.75/3.25 2.00/2.50 2.00/2.50 2.75/3.25
Nickel .25 .40 .25 .25 .40 .25 .25
Molybdenum .90/1.10 .90/1.10 .90/1.10 .90/1.10 .90/1.10 .90/1.10 .90/1.10
Copper .25 .40 .25 .25 .40 .25 .25
Other Elements .20/.30 V .03 Max. V .02 Max. V .20/.30 V .03 Max. V .02 Max. V .20/.30 V
.015/.035 Ti Mandatory Mandatory .015/.035 Ti Mandatory Mandatory .015/.035 Ti
.001/.003 B TCVN TCVN .001/.003 B TCVN TCVN .001/.003 B
Mandatory Mandatory
TCVN TCVN
Heat Treatment Required Q&T, Q&T, Q&T, Q&T, Q&T, Q&T, Q&T,
QQ&T QQ&T QQ&T QQ&T QQ&T QQ&T QQ&T
or NQ&T or NQ&T or NQ&T or NQ&T or NQ&T or NQ&T or NQ&T
over 4" over 4" over 4" over 4" over 4" over 4" over 4"
17
A543 A543 A543 A543 A543 A543

Type B Type C Type B Type C Type B Type C A553
SPECIFICATION Class 1 Class 1 Class 2 Class 2 Class 3 Class 3 Type 1
(Yield Point if
designated YP)
ISG Plate
Thickness (Max. in.) 8* 8* 6* 6* 10* 10* 2*
Carbon .20 .18 .20 .18 .20 .18 .13
Manganese .40 .40 .40 .40 .40 .40 .90
Phosphorus .020 .020 .020 .020 .020 .020 .035
Sulfur .020 .020 .020 .020 .020 .020 .035
Silicon .15/.40 .15/.40 .15/.40 .15/.40 .15/.40 .15/.40 .15/.40**
Chromium 1.00/1.90 1.00/1.90 1.00/1.90 1.00/1.90 1.00/1.90 1.00/1.90 ■
Nickel 2.25/4.00 2.00/3.50 2.25/4.00 2.00/3.50 2.25/4.00 2.00/3.50 8.50/9.50

Molybdenum .20/.65 .20/.65 .20/.65 .20/.65 .20/.65 .20/.65 ■
Copper ■ ■ ■ ■ ■ ■ ■
Other Elements .03 V .03 V .03 V .03 V .03 V .03 V ■
Heat Treatment Required Q&T to Q&T to Q&T to Q&T to Q&T to Q&T to Q&T
4" incl.; 4" incl.; 4" incl.; 4" incl.; 4" incl.; 4" incl.; TCVN
double double double double double double
Q&T or Q&T or Q&T or Q&T or Q&T or Q&T or
N and N and N and N and N and N and
Q&T Q&T Q&T Q&T Q&T Q&T
required required required required required required
over 4" over 4" over 4" over 4" over 4" over 4"
* Consult ISG Plate for plates over thickness listed.
** Silicon may be less than 0.15% provided total aluminum is 0.030% or greater.
18
A572† A572†▲ A572†▲ A572† A572†

Grade 42 Grade 50 Grade 55 Grade 60 Grade 65 A573
SPECIFICATION A562 Type 2# Type 2# Type 2# Type 2# Type 2# Grade 58
Type of Steel Alloy HSLA HSLA HSLA HSLA HSLA Carbon
Tensile Strength (ksi) 55/75 60 Min. 65 Min. 70 Min. 75 Min. 80 Min. 58/71
Yield Strength (Min. ksi) 30 42 YP 50 YP 55 YP 60 YP 65 YP 32 YP
(Yield Point if
designated YP)
Spec. Thickness (Max. in.) 2 6 4 2 11/4 11/4 11/2
ISG Plate
Thickness (Max. in.) 2 refer to 18 refer to 12 refer to 4 refer to 9 refer to 8 11/2
Carbon .12 .21 .23 .25 .26 .26 to 1/2" .23
incl.; .23
over 1/2 -
11/4" incl.
Manganese 1.20 1.35** 1.35** 1.35** 1.35** 1.35 Max.*** .60/.90
to 1/2" incl.;
1.65 Max.
over 1/2 -
11/4" incl.
Phosphorus .035 .040 .04 .04 .04 .04 .035
Sulfur .035 .050 .05 .05 .05 .05 .04
Silicon .15/.50 .40 .40 to .40 to .40 .40 .10/.35
to 11/2" 11/2" incl.; 11/2" incl.;
incl.; .15/.40 .15/.40 .15/.40
over 11/2" over 11/2" over 11/2"
Chromium ■ - - - - - -
Nickel ■ - - - - - -
Molybdenum ■ - - - - - -
Copper .15 - - - - - -
Other Elements Ti Min. .01/.15 V .01/.15 V .01/.15 V .01/.15 V .01/.15 V -
4XC
Heat Treatment Required N - - - - - -
** For each reduction of 0.01% below the specified carbon maximum, an increase of 0.06% manganese above the specified
maximum is permitted up to 1.50%.
*** 1.65 Max. Mn permissible with reduction of carbon to .21 maximum.
▲ Also produced as V-Star.®
# May also be produced as Type 1 with V replaced by .005/.05 Cb. Inquire with ISG Plate for Types 3 and 5.
19
A573 A573 A588†* A588†▲▲* A633†

SPECIFICATION Grade 65 Grade 70 Grade A Grade B A612† Grade A
Type of Steel Carbon Carbon HSLA HSLA Carbon HSLA
Tensile Strength (ksi) 65/77 70/90 70 Min. 70 Min. 83/105 63/83
to 4" incl.; to 4" incl.; to 1/2" incl.;
67 Min. over 67 Min. over 81/101 over
1
4-5" incl.; 4-5" incl.; /2 - 1" incl.
63 Min. over 63 Min. over
5-8" incl. 5-8" incl.
Yield Strength (Min. ksi) 35 YP 42 YP 50 YP to 50 YP to 50 42 YP
(Yield Point if 4" incl.; 46 4" incl.; 46
designated YP) over 4-5" over 4-5"
incl.; 42 over incl.; 42 over
5-8" incl. 5-8" incl.
Spec. Thickness (Max. in.) 11/2 11/2 8 8 1 incl. 4
ISG Plate
Thickness (Max. in.) 11/2 11/2 8 8 1 incl. 4
Carbon .24 to 1/2" .27 to 1/2" .19 .20 .25 .18
incl.; .26 incl.; .28
over 1/2 - over 1/2 -
11/2" incl. 11/2" incl.
Manganese .85/1.20 .85/1.20 .80/1.25** .75/1.35** 1.00/1.50 1.00/1.35
Phosphorus .035 .035 .04 .04 .035 .035
Sulfur .04 .04 .05 .05 .025 .04
Silicon .15/.40 .15/.40 .30/.65 .15/.50 .15/.50 .15/.50
Chromium - - .40/.65 .40/.70 .25 -
Nickel - - .40 .50 .25 -
Molybdenum - - - - .08 -
Copper - - .25/.40 .20/.40 .35 -
Other Elements - - .02/.10 V .01/.10 V .08 V .05 Cb
Heat Treatment Required - - - - - N
▲ Also produced as Cor-Ten® B.
▲▲ Also produced as Mayari-R50® and R60; refer other A588 grades to ISG Plate.
* ASTM G101 corrosion index minimum must also be met.
** For each 0.01% reduction below the specified maximum for carbon, an increase of 0.06% manganese above the specified
maximum is permitted up to 1.50%.
20
A656† A656†▲ A656†▲ A656†▲

A633† A633 A633† Grade 50 Grade 50 Grade 60 Grade 70
SPECIFICATION Grade C Grade D Grade E Type 3 Type 7 Type 7 Type 7
Type of Steel HSLA HSLA HSLA HSLA HSLA HSLA HSLA
Tensile Strength (ksi) 70/90 to 70/90 to 80/100 to 60 Min. 60 Min. 70 Min. 80 Min.
2 1/2" incl.; 2 1/2" incl.; 4" incl.;
65/85 over 65/85 over 75/95 over
2 1/2 -4" incl. 2 1/2 -4" incl. 4-6" incl.
Yield Strength (Min. ksi) 50 YP to 50 YP to 60 YP to 50 YP 50 YP 60 YP 70 YP
(Yield Point if 21/2" incl.; 2 1/2" incl.; 4" incl.;
designated YP) 46 over 46 over 55 over
2 1/2 -4" incl. 2 1/2 -4" incl. 4-6" incl.
Spec. Thickness (Max. in.) 4 4 6 2 2 11/2 1
ISG Plate
Thickness (Max. in.) refer to 12 4 6 2 2 11/2 1
Carbon .20 .20 .22 .18 .18 .18 .18
Manganese 1.15/1.50; .70/1.35 to 1.15/1.50 1.65 1.65 1.65 1.65
1.60 11/2" incl.;
if C is 1.00/1.60
.18 Max. over 11/2 -
4" incl.
Phosphorus .035 .035 .035 .025 .025 .025 .025
Sulfur .04 .04 .04 .035 .035 .035 .035
Silicon .15/.50 .15/.50 .15/.50 .60 .60 .60 .60
Chromium - .25 - - - - -
Nickel - .25 - - - - -
Molybdenum - .08 - - - - -
Copper - .35 - - - - -
Other Elements .01/.05 Cb - .04/.11 V .08 V .008/.15 V .008/.15 V .008/.15 V
.03 N .008/.15 Cb .008/.10 Cb .008/.10 Cb .008/.10 Cb
.05 Cb .020 N .020 N .020 N .020 N
.20 .20 .20
(Cb+V) (Cb+V) (Cb+V)
Heat Treatment Required N N N - - - -
Double N
over 3"
† Post-weld heat treatment may degrade heat-affected zone strength and toughness. Pretesting of specific welding and post-
weld heat treating procedures is recommended to assure optimization of final property levels.
▲ Also produced as BethStar.®
BethStar Brochure
21
A656†▲▲
Grade 80 A662 A662 A662 A678 A678▲▲▲ A678
SPECIFICATION Type 7 Grade A Grade B Grade C Grade A Grade B Grade C
Type of Steel HSLA Carbon Carbon Carbon HSLA HSLA HSLA
Requirements for Delivery A6 A20 A20 A20 A6* A6* A6*
Tensile Strength (ksi) 90 Min. 58/78 65/85 70/90 70/90 80/100 95/115 to
3
/4" incl.;
90/110 over
3
/4 -11/2" incl.;
85/105 over
11/2 -2" incl.
Yield Strength (Min. ksi) 80 YP 40 40 43 50 60 75 to 3/4" incl.;
(Yield Point 70 over 3/4 -11/2"
designated YP) incl.; 65 over
11/2-2" incl.
3
Spec. Thickness (Max. in.) /4 - - - 11/2 2 1/2 2
ISG Plate
3
Thickness (Max. in.) /4 2 2 2 11/2 2 1/2 2
Carbon .18 .14 .19 .20 .16 .20 .22
Manganese 1.65 .90/1.35 .85/1.50 1.00/1.60 .90/1.50 .70/1.35 to 1.00/1.60
11/2" incl.;
1.00/1.60
over 11/2 -
2 1/2" incl.
Phosphorus .025 .035 .035 .035 .035 .035 .035
Sulfur .035 .035 .035 .035 .04 .04 .04
Silicon .60 .15/.40 .15/.40 .15/.50 .15/.50 .15/.50 .20/.50
Chromium - ■ ■ ■ .25 .25 .25
Nickel - ■ ■ ■ .25 .25 .25
Molybdenum - ■ ■ ■ .08 .08 .08
Copper - ■ ■ ■ .35; .35; .35;
.20 Min. .20 Min. .20 Min.
when when when
specified specified specified
Other Elements .008/.15 V - - - - - -
.008/.10 Cb
.020 N
.20
(Cb+V)
Heat Treatment Required - N N over 11/2" N over 11/2" Q&T Q&T Q&T
* Except one tension test required per each plate as heat treated.
▲▲ Also produced as BethStar.®
▲▲▲ Also produced as RQC-60 (Q&T).
22
A709 A709† A709†† A710††

A678† A709** Grade† Grade Grade Grade A
SPECIFICATION Grade D Grades HPS 50W HPS 70W HPS 100W Class 3
Type of Steel HSLA - HSLA HSLA Alloy Alloy
Requirements for Delivery A6* - A6 A6 A6 A6
Tensile Strength (ksi) 90/110 - 70 Min. 85/110 110/130 85 Min.
to 2" incl.;
75 Min.
over 2-4"
incl.; 70
Min. over
4-8" incl.
Yield Strength (Min. ksi) 75 - 50 70 100 80 to 1.25";
(Yield Point if 75 over 1.25-
designated YP) 2" incl.; 65 over
2-4" incl.; 60
over4-8" incl.
Spec. Thickness (Max. in.) 3 - 4 4 2.5 -
ISG Plate
Thickness (Max. in.) 3 - 4 4 2.5 8
Carbon .22 - .11 .11 .08 .07
Manganese 1.15/1.50 - 1.10/1.35 1.10/1.35 .95/1.50 .40/.70
Phosphorus .035 - .020 .020 .015 .025
Sulfur .04 - .006 .006 .006 .025
Silicon .15/.50 - .30/.50 .30/.50 .15/.35 .40
Chromium .25 - .45/.70 .45/.70 .40/.65 .60/.90
Nickel .25 - .25/.40 .25/.40 .65/1.00 .70/1.00
Molybdenum .08 - .02/.08 .02/.08 .40/.65 .15/.25
Copper .35; - .25/.40 .25/.40 .90/1.20 1.00/1.30
.20 Min.
when
specified
Other Elements .04/.11 V - .04/.08 V .04/.08 V .01/.03 Cb .02 Min. Cb
.05 Cb .010/.040 Al .010/.040 Al
.01/.03 N .015 N .015 N
CT CT
Heat Treatment Required Q&T - - Q&T††† Q&T
* Except one tension test required per each plate as heat treated.
** See listing of all Bridge steel grades on page 44.
†† It is important to note that this grade of steel may be susceptible to cracking in the heat-affected zone of welds during post-
weld heat treatment (stress relief) or elevated temperature service. Also, post-weld heat treatment or elevated temperature
service may degrade heat affected zone toughness. Therefore, ISG Plate recommends that careful consideration be given to
these phenomena by competent welding engineers before application.
††† Is available as non-Q&T (TMCP) refer to ISG Plate.
Spartan Brochure HPS 70W Brochure HPS 50W Brochure HPS 100W Brochure
23
A736††
A724† A724† A724† Grade A A737† A737†
SPECIFICATION Grade A Grade B Grade C Class 3 Grade B Grade C
Type of Steel Carbon Carbon Carbon Alloy HSLA HSLA
Tensile Strength (ksi) 90/110 95/115 90/110 85/105 to 70/90 80/100
2" incl.;
75/95 over
2-4" incl.;
70/90 over
4-8" incl.
Yield Strength (Min. ksi) 70 75 70 75 to 50 60
(Yield Point if 2" incl.;
designated YP) 65 over
2-4" incl.;
60 over
4-8" incl..
ISG Plate
Thickness (Max. in.) 7/8 7/8 2 8 4 4
Carbon .18 .20 .22 .07 .20 .22
Manganese 1.00/1.60 1.00/1.60 1.10/1.60 .40/.70 1.15/1.50 1.15/1.50
1.60 Max. if
C is .18 Max.
Phosphorus .035 .035 .035 .025 .035 .035
Sulfur .035 .035 .035 .025 .030 .030
Silicon .55 .50 .20/.60 .40 .15/.50 .15/.50
Chromium .25 .25 .25 .60/.90 ■ ■
Nickel .25 .25 .25 .70/1.00 ■ ■
Molybdenum .08 .08 .08 .15/.25 ■ ■
Copper .35 .35 .35 1.00/1.30 ■ ■
Other Elements .08 V .08 V .08 V .02 Min. Cb .05 Cb .04/.11 V

.005 B .03 N
.05
Cb may
be present
Heat Treatment Required Q&T Q&T Q&T Q&PHT N N
†† It is important to note that this grade of steel may be susceptible to cracking in the heat-affected zone of welds during post-weld
heat treatment (stress relief) or elevated temperature service. Also, post-weld heat treatment or elevated temperature service
may degrade heat affected zone toughness. Therefore, ISG Plate recommends that careful consideration be given to these
phenomena by competent welding engineers before application.
24
A829 A841† A841† A841†

A738† A738† & Grade A Grade B Grade A
SPECIFICATION Grade A Grade B A808† A830** Class 1 Class 1 Class 2
Type of Steel Carbon Carbon HSLA - HSLA HSLA HSLA
Requirements for Delivery A20 A20 A6 - A20 A20 A20
Tensile Strength (ksi) 75/95 85/102 65 Min. to - 70/90 to 70/90 to 80/100 to
2" incl.; 21/2" incl.; 21/2" incl.; 21/2" incl.;
60 Min. 65/85 over 65/85 over 75/95 over
over 2-2 1/2" 21/2-4" 21/2-4" 21/2-4"
Yield Strength (Min. ksi) 45 60 50 to - 50 to 50 to 60 to

(Yield Point if 11/2" incl.; 21/2" incl.; 21/2" incl.; 21/2" incl.;
designated YP) 46 over 45 over 45 over 55 over
11/2 -2" incl.; 21/2 -4" 21/2 -4" 21/2 -4"
42 over
2-21/2" incl.
Spec. Thickness (Max. in.) - 2 1/2 2 1/2 - 4 4 4
ISG Plate
Thickness (Max. in.) 4 2 1/2 2 1/2 - 4 4 4
Carbon .24 .20 .12 - .20 .15 .20
Manganese 1.50 .90/1.50 1.65 - .70/1.35 .70/1.35 .70/1.35
to 2 1/2" incl.; to 11/2" incl.; to 11/2" incl.; to 11/2" incl.;
1.60 1.00/1.60 1.00/1.60 1.00/1.60
over 2 1/2" over 11/2 -4" over 11/2 -4" over 11/2 -4"
Phosphorus .035 .030 .035 - .030 .030 .030
Sulfur .035 .030 .04 - .030 .025 .030
Silicon .15/.50 .15/.55 .15/.50 - .15/.50 .15/.50 .15/.50
Chromium .25 .30 - - .25 .25 .25
Nickel .50 .60 - - .25 .60 .25
Molybdenum .08 .20 to - - .08 .30 .08
1.5" incl.;
.30 Max.
over 1.5"
Copper .35 .35 - - .35 .35 .35
Other Elements .07 V .07 V .10 V - .06 V .06 V .06 V
.04 .04 .02/.10 Cb .03 Cb .03 Cb .03 Cb
Cb when Cb .15 .02 Min. Al .02 Min. Al .02 Min. Al
specified .08 (V+Cb)
.08 (V+Cb)
(V+Cb)
Heat Treatment Required N or Q&T Q&T - - TMCP TMCP TMCP
to 2 1/2" incl.; LCVN LCVN LCVN
Q&T over 2 1/2"
** SAE or ASTM Grades, see pages 32-34.
25
A841† A871† A871†

Grade B Grade 60 Grade 65 A945† A945†▲ A1010* A1010*
SPECIFICATION Class 2 A852† Type II# Type II# Grade 50 Grade 65 Grade 40 Grade 50
Type of Steel HSLA HSLA HSLA HSLA HSLA HSLA Stainless Stainless
Tensile Strength (ksi) 80/100 to 90/110 75 Min. 80 Min. 70/90 78/100 66 Min. 70 Min.
21/2" incl.;
75/95 over
21/2-4"
Yield Strength (Min. ksi) 60 to 70 60 65 50 65 40 50
(Yield Point if 21/2" incl.;
designated YP) 55 over
21/2-4"
Spec. Thickness (Max. in.) 4 4 - - 2 11/4 1 1
ISG Plate
Thickness (Max. in.) 4 4 11/4 3/4 2 11/4 4 4
Carbon .15 .19 .20 .20 .10 .10 .030 .030
Manganese .70/1.35 .80/1.35 .75/1.35 .75/1.35 1.10/1.65 1.10/1.65 1.50 1.50
to 11/2" incl.;
1.00/1.60
over 11/2-4"
Phosphorus .030 .035 .04 .04 .025 .025 .040 .040
Sulfur .025 .040 .05 .05 .010 .010 .030 .030
Silicon .15/.50 .20/.65 .15/.50 .15/.50 .10/.50 .10/.50 1.00 1.00
Chromium .25 .40/.70 .40/.70 .40/.70 .20 .20 10.5/12.5 10.5/12.5
Nickel .60 .50 .50 .50 .40 .40 1.50 1.50
Molybdenum .30 - - - .08 .08 - -
Copper .35 .20/.40 .20/.40 .20/.40 .35 .35 - -
Other Elements .06 V .02/.10 V .01/.10 V .01/.10 V .10 V .10 V .030 N .030 N
.03 Cb Mandatory F/G/P F/G/P .05 Cb .05 Cb
LCVN Mandatory Mandatory .08 Al .08 Al
LCVN LCVN F/G/P F/G/P
Mandatory Mandatory
LCVN LCVN
Heat Treatment Required TMCP Q&T - - Coatesville Coatesville Tempered Tempered
LCVN may require may require
N or Q&T Q&T
# Also available as Type I, III, IV. Inquire with ISG Plate.
* Also available as Duracorr,® See page 37.
▲ Provided to the U.S. Navy as HSLA-65 with TCVN and additional chemical and mechanical requirements.
26
AIRCRAFT QUALITY STEEL
Alloy 4130 Alloy 4130 Mod. Alloy 4140 Alloy 4340

SPECIFICATION (AMS 6345) (AMS 6385) (AMS 6395) (AMS 6359)
Type of Steel Alloy Alloy Alloy Alloy
Requirements for Delivery - - - -
Tensile Strength (ksi) 85 Max. 135 Min. - -
Annealed Normalized &
90 Min. > 3/16" tempered*
Condition N
Yield Strength (Min. ksi) 70 > 3/16" 115 - -
(Yield Point if Condition N Normalized &
designated YP) tempered*
Spec. Thickness (Max. in.) 6 - - -
ISG Plate
Thickness (Max. in.) 6 2 6 6
Carbon .28/.33 .27/.33 .38/.43 .38/.43
Manganese .40/.60 .45/.65 .75/1.00 .60/.85
Phosphorus .025 .025 .025 .025
Sulfur .025 .025 .025 .025
Silicon .20/.35 .55/.75 .15/.35 .15/.35
Chromium .80/1.10 1.00/1.50 .80/1.10 .70/.90
Nickel .25 .25 .25 1.65/2.00
Molybdenum .15/.25 .40/.60 .15/.25 .20/.30
Copper - .35 .35 .35
Other Elements (See API 2H) - .20/.30 V - -
Heat Treatment Required Condition A - Annealed Annealed Annealed
Annealed; to Rockwell to Rockwell to Rockwell
Condition N - C-24 Max. C-25 Max. C-25 Max.
Normalized
to 3/4" incl.;
Q&T over 3/4"
Remarks CT CT CT CT
Will meet Will meet Will meet Will meet
AMS 2301 AMS 2301 AMS 2301 AMS 2301
AMS 6350
to Rockwell
C-25 Max.
* Of capability test coupon.
27
AMERICAN BUREAU OF SHIPPING SPECIFICATIONS
ABS† ABS† ABS† ABS† ABS†

SPECIFICATION Grade A Grade B Grade D Grade E AH32
Tensile Strength (ksi) 58/75 58/75 58/75 58/75 64/85
Yield Strength (Min. ksi) 34 34 34 34 46
(Yield Point if
designated YP)
Spec. Thickness (Max. in.) - - - - -
ISG Plate
Thickness (Max. in.) 6 6 6 1/2 6 8
Carbon .21* .21* .21* .18* .18
Manganese 21/2 x C .60 min. .60 min. .70 min. .90/1.60

Min.
Phosphorus .035 .035 .035 .035 .035
Sulfur .035 .035 .035 .035 .035
Silicon .50 .35 .10/.35 .10/.35 .10/.50
Chromium - - - - .20
Nickel - - - - .40
Molybdenum - - - - .08
Copper - - - - .35
Other Elements F/G/P>2" F/G/P>1" F/G/P F/G/P Ti .02
Heat Treatment Required N over 2" N N N N
over 2" TCVN req. TCVN over 1/2"
TCVN over 1" Q&T over
6 to 8"
TCVN req.
† Similar to ASTM A131.
* C + Mn/6 = .40 max.
28
CON TINUED
AMERICAN BUREAU OF SHIPPING SPECIFICATIONS
ABS† ABS† ABS† ABS† ABS†

SPECIFICATION DH32 EH32 AH36 DH36 EH36
Tensile Strength (ksi) 64/85 64/85 71/90 71/90 71/90
Yield Strength (Min. ksi) 46 46 51 51 51
(Yield Point if
designated YP)
Spec. Thickness (Max. in.) - - - - -
ISG Plate
Carbon .18 .18 .18 .18 .18
Manganese .90/1.60 .90/1.60 .90/1.60 .90/1.60 .90/1.60
Phosphorus .035 .035 .035 .035 .035
Sulfur .035 .035 .035 .035 .035
Silicon .10/.50 .10/.50 .10/.50 .10/.50 .10/.50
Chromium .20 .20 .20 .20 .20
Nickel .40 .40 .40 .40 .40
Molybdenum .08 .08 .08 .08 .08
Copper .35 .35 .35 .35 .35
Other Elements F/G/P, F/G/P, F/G/P, F/G/P, F/G/P,
Ti .02 Ti .02 Ti .02 Ti .02 Ti .02
Heat Treatment Required N N to 6" N N over 1/2" N
over 1/2" Q&T over 1/2" Q&T Q&T
over Q&T over over
6 to 7" over 6 to 7" 6 to 7"
6 to 8"
Remarks TCVN TCVN TCVN TCVN TCVN
† Similar to ASTM A131.
29
AMERICAN PETROLEUM INSTITUTE SPECIFICATIONS
API 2H† API 2H† API 2Y†**** API 2Y† API 2Y†▲
SPECIFICATION Grade 42 Grade 50 Grade 50 Grade 50T Grade 60
Type of Steel HSLA HSLA HSLA HSLA HSLA
Tensile Strength (ksi) 62/82 70/90 65 Min. 70 Min. 75 Min.
1
Yield Strength (Min. ksi) 42 50 to 2 /2" 50/75 to 50/80 to 60/90 to
(Yield Point if incl.; 47 1" incl.; 1" incl.; 1" incl.;
designated YP) over 2 1/2" 50/70 50/75 60/85
Spec. Thickness (Max. in.) 4 4 6 6 4
ISG Plate
Carbon .18 .18 .16 .16 .16
Manganese .90/1.60 1.15/1.60 1.15/1.60 1.15/1.60 1.15/1.60
Phosphorus .030 .030 .030 .030 .030
Sulfur .010 .010 .010 .010 .010
Silicon .05/.40 .05/.40 .15/.50 .15/.50 .15/.50
Chromium *** *** .25 .25 .25
Nickel *** *** .75 .75 1.0
Molybdenum *** *** .08 .08 .15
Copper *** *** .35 .35 .35
Other Elements .020/.06 Al .020/.06 Al .020/.06 Al .020/.06 Al .020/.06 Al
.04 Cb .01/.04 Cb .03 Cb .03 Cb .03 Cb
.020 Ti, .012 N .020 Ti, .012 N .012 N .012 N .012 N
.0100 Ce .0100 Ce .003/.02 Ti .003/.02 Ti .003/.02 Ti
Ce, N, B, V, Zr Ce, N, B, V, Zr N, B, V, Zr, Ce N, B, V, Zr, Ce N, B, V, Zr, Ce
not intentionally not intentionally not intentionally not intentionally not intentionally
added added added added added
Heat Treatment Required N N Q&T Q&T Q&T
Remarks F/G/P F/G/P F/G/P F/G/P F/G/P
CE .43 to 21/2" incl. CE .43 to 21/2" incl. Ti addition Ti addition Ti addition
.45 over 2 1/2". .45 over 2 1/2". based on N. based on N. based on N.
TCVN Req. TCVN Req. CE .39 CE .39 CE .42
to 11/2" incl.; to 11/2" incl.; to 11/2" incl.;
.41 to .41 to .45 to 4".
31/2" incl.; 31/2" incl.; TCVN Req.
.43 to 6". .43 to 6".
TCVN Req. TCVN Req.
▲ Inquiry basis only.
*** Residuals must be reported.
CE (IIW) = C + Mn /6 + (Cr+Mo+V)/5 + (Cu+Ni)/15
**** A Grade 42 is also available with properties and chemistry of API-2W Grade 42.
API Steels Brochure
30
CON TINUED AMERICAN PETROLEUM INSTITUTE SPECIFICATIONS
API-2W†▲ API-2W†▲ API-2W†▲ API-2W†▲

SPECIFICATION API-2MT-1† Grade 42 Grade 50 Grade 50T Grade 60
Type of Steel HSLA HSLA HSLA HSLA HSLA
Tensile Strength (ksi) 70/90 62 65 70 75
Yield Strength (Min. ksi) 50 42/67 1" 50/75 to 50/80 to 60/90 to
(Yield Point if incl.; 42/62 1" incl.; 1" incl.; 1" incl.;
designated YP) over 1" 50/70 50/75 60/85
Spec. Thickness (Max. in.) 2 1/2 6 6 6 4
ISG Plate
Thickness (Max. in.) 2 1/2 2 2 2 2
Carbon .15 .16 .16 .16 .16
Manganese 1.15/1.60 .90/1.35 to 1.15/1.60 1.15/1.60 1.15/1.60
11/2" incl.;
.90/1.60
over 11/2"
Phosphorus .030 .03 .03 .03 .03
Sulfur .010 .010 .010 .010 .010
Silicon .15/.40 .05/.50 .05/.50 .05/.50 .05/.50
Chromium - .25 .25 .25 .25
Nickel - .75 .75 .75 1.0
Molybdenum - .08 .08 .08 .15
Copper - .35 .35 .35 .35
Other Elements .010/.040 Cb .03 Cb .03 Cb .03 Cb .03 Cb
.020/.060 Al .012 N .012 N .012 N .012 N
.080 V, .020 Ti .02/.06 Al .02/.06 Al .02/.06 Al .02/.06 Al
.012 N, .010 Ce .003/.02 Ti .003/.02 Ti .003/.02 Ti .003/.02 Ti
N, Zr or B N, B, V, Zr, Ce N, B, V, Zr, Ce N, B, V, Zr, Ce N, B, V, Zr, Ce
not intentionally not intentionally not intentionally not intentionally not intentionally
added added added added added
Heat Treatment Required As rolled, TMCP TMCP TMCP TMCP
N or Q&T
Remarks CE .43 to 2" incl. Ti based on N, Ti based on N, Ti based on N, Ti based on N,
.45 to 2 1/2". F/G/P, F/G/P, F/G/P, F/G/P,
CE .39 to 11/2" incl. CE .39 to 11/2" incl. CE .39 to 11/2"incl. CE .42 to 11/2"incl.
.41 to 31/2" incl. .41 to 31/2" incl. .41 to 31/2" incl. .45 to 4"
.43 to 6" .43 to 6" .43 to 6" TCVN Req.
TCVN Req. TCVN Req. TCVN Req.
▲ Inquiry basis only.
API Steels Brochure
31
ASTM CHEMISTRY-ONLY STEELS
[Covered by A829 (Alloy), A830 (Carbon)]
No mechanical testing is required for delivery of chemistry-only steels. They meet only the
chemical and dimensional limits specified by the customer. These steels were previously
known as AISI Chemistry-Only Grades. These steels are also nearly identical to the SAE
grades of the same name.
The designation number of a chemistry-only steel indicates the chemical composition of

that grade. The first two digits establish the family by alloy content. For example:
10XX — carbon steels

41XX — chromium-molybdenum steels
43XX — nickel-chromium-molybdenum steels
61XX — chromium-vanadium steels
86XX — nickel-chromium-molybdenum steels
EXXXX — E designates electric furnace quality
The last two digits in the grade designation indicate the mid-point of the carbon range. For
example, 4130 is a chrome-moly steel that has an approximate mid-point of .30% carbon
in the specified carbon range.
The following is a more detailed analysis of the commonly used chemistry-only steels,
including ISG Plate’s thickness limits. Other chemical compositions are available
upon request.
A830 A830 A830 A830 A830 A830 A830
SPECIFICATION 1006 1008 1009* 1010 1012 1015 1017
Type of Steel Carbon Carbon Carbon Carbon Carbon Carbon Carbon
ISG Plate
Thickness (Max. in.) 16 18 18 18 18 18 18
Carbon .08 .10 .15 .08/.13 .10/.15 .13/.18 .15/.20
Manganese .45 .50 .60 .30/.60 .30/.60 .30/.60 .30/.60
Phosphorus .035 .035 .035 .035 .035 .035 .035
Sulfur .04 .04 .04 .04 .04 .04 .04
Silicon - - - - - - -
Molybdenum - - - - - - -
Chromium - - - - - - -
Nickel - - - - - - -
Other Elements - - - - - - -
Remarks Also available - - - - - -
as ISG Plate HP
Magnet Steel
* Also available as ASTM A827 for forging and similar applications with .035 Max. Phosphorus, .040 Max. Sulfur.
HP Magnet Steel Brochure
32
CON TINUED ASTM CHEMISTRY-ONLY STEELS
A830 A830 A830 A830 A830 A830
SPECIFICATION 1020* 1023 1025 1030 1035* 1040*
Type of Steel Carbon Carbon Carbon Carbon Carbon Carbon
ISG Plate
Thickness (Max. in.) 18 18 18 18 18 18
Carbon .18/.23 .20/.25 .22/.28 .28/.34 .32/.38 .37/.44
Manganese .30/.60 .30/.60 .30/.60 .60/.90 .60/.90 .60/.90
Phosphorus .035 .035 .035 .035 .035 .035
Sulfur .04 .04 .04 .04 .04 .04
Silicon ** ** ** ** ** .15/.40
Molybdenum - - - - - -
Chromium - - - - - -
Nickel - - - - - -
Remarks - - - - - -
A830 A830 A829 A829 A829 A829

SPECIFICATION 1045* 1060 4130 4140 4142 E4340
Type of Steel Carbon Carbon Alloy Alloy Alloy Alloy
ISG Plate
Thickness (Max. in.) 18 10 12 16 16 12
Carbon .43/.50 .55/.65 .27/.34 .36/.44 .38/.46 .37/.44
Manganese .60/.90 .60/.90 .35/.60 .70/1.00 .70/1.00 .60/.85
Phosphorus .035 .035 .035 .035 .035 .025
Sulfur .04 .04 .040 .040 .040 .025
Silicon .15/.40 .15/.40 .15/.35 .15/.35 .15/.35 .15/.35
Molybdenum - - .15/.25 .15/.25 .15/.25 .20/.30
Chromium - - .80/1.15 .80/1.15 .80/1.15 .65/.90
Nickel - - - - - 1.65/2.00
Remarks - CT - - - -
* Also available as ASTM A827 for forging and similar applications with .035 Max. Phosphorus, .040 Max. Sulfur.
** When silicon required, range should be .15/.40 unless otherwise specified.
33
CON TINUED ASTM CHEMISTRY-ONLY STEELS
A829 A829 A829 A829 A829 A829
SPECIFICATION 6150 8615 8617 8620 8625 8630
ISG Plate
Carbon .46/.54 .12/.18 .15/.21 .17/.23 .22/.29 .27/.34
Manganese .60/.90 .60/.90 .60/.90 .60/.90 .60/.90 .60/.90
Phosphorus .035 .035 .035 .035 .035 .035
Sulfur .040 .040 .040 .040 .040 .040
Silicon .15/.35 .15/.35 .15/.35 .15/.35 .15/.35 .15/.35
Molybdenum - .15/.25 .15/.25 .15/.25 .15/.25 .15/.25
Chromium .80/1.15 .35/.60 .35/.60 .35/.60 .35/.60 .35/.60
Nickel - .40/.70 .40/.70 .40/.70 .40/.70 .40/.70
Other Elements .15 Min. V - - - - -
Remarks - - - - - -
ISG PLATE FREE MACHINING STEELS

Clean-Cut® 20 Clean-Cut® 45 C1119™ C1144™
ISG Plate
Carbon .14/.22 .42/.50 .17/.23 .40/.50
Manganese 1.20/1.50 1.20/1.50 1.00/1.30 1.00/1.30
Phosphorus .04 .04 .04 .03
Sulfur .06/.12 .06/.12 .20/.33 .20/.33
Silicon .10/.40 .10/.40 .30 .30
Heat Treatment Required - Stress relieved over 6" as cut - -
edge; over 8" as mill edge
Clean-Cut® Alloy Steels
The following steels are produced with specification sulfur .02/.040.
See other chemistry/mechanical properties/heat treatment listed in this brochure.
ASTM A829 Grades 4140, 4142, 4150, 8620 ISG Plate MTD® #1, #2, and #4.
Free-Machining Brochure
34
ISG PLATE PROPRIETARY GRADES
SPECIFICATION SPA-90* T-1®* T-1® Type A* T-1® Type B* T-1® Type C* Lukens® 130* Lukens® 690Z*▲
Requirements for Delivery A6, A20** A6, A20** A6, A20** A6, A20** A6, A20** A6
Tensile Strength (ksi) 110/130 to 110/130 110/130 110/130 110/130 to Info. only 110/136
2 1/2" incl.; 2 1/2" incl.;
100/130 100/130
over 2 1/2" over 2 1/2"
Yield Strength (Min. ksi) 100 to 2 1/2" 100 100 100 100 to 2 1/2" 130 100
designated YP) over 2 1/2" over 2 1/2"
Spec. Thickness (Max. in.) 8 2 1/2 11/4 2 6 2 6.5
ISG Plate
Thickness (Max. in.) 8 2 1/2 11/4 2 6 Refer to 4 6.5
Carbon .14/.21 .10/.20 .12/.21 .12/.21 .14/.21 .12/.18 .15
Manganese .95/1.30 .60/1.00 .70/1.00 .95/1.30 .95/1.30 1.55 1.25
Phosphorus .035 .035 .035 .035 .035 .025 .015
Sulfur .040 .040 .040 .040 .040 .003 .005
Silicon .15/.35 .15/.35 .20/.35 .20/.35 .15/.35 .15/.50 .15/.55
Chromium 1.00/1.50 .40/.65 .40/.65 .40/.65 1.00/1.50 .65 .70
.80 if
approved
by customer
Nickel 1.20/1.50 .70/1.00 - .30/.70 1.20/1.50 1.00 1.0/3.5
Molybdenum .40/.60 .40/.60 .15/.25 .20/.30 .40/.60 .60 .70
Copper ■ .15/.50 .20/.40 .20/.40 ■ - .30
if specified if specified
Other Elements .03/.08 V .03/.08 V .03/.08 V .03/.08 V .03/.08 V .08 V, CT .005B
.0005/.006 B .01/.03 Ti .0005/.005 B .04 Cb .04Ti
.005 B .08 V
Heat Treatment Required Q&T Q&T Q&T Q&T Q&T Q&T Q&T
Remarks LCVN LCVN
** A20: Raise tensile strength range by 5 ksi.
▲ Also available as ABS grades EQ/FQ 63/70
T-1 Brochure
Lukens 130 Brochure
Lukens 690Z Brochure
35
CON TINUED ISG PLATE PROPRIETARY GRADES
RQC-60 RQC-60
SPECIFICATION (Q&T) (N) RQC-80 RQC-90 RQC-100 Spartan® I††
Type of Steel Carbon Carbon Carbon Carbon Carbon Alloy
Requirements for Delivery A6 A6 A6 A6 A6 A6, A20
Tensile Strength (ksi) 80/100 to 70/90 to 95 100 110 60/110*
21/2" incl.; 21/2" incl.; available
75/95 over 65/85 over
21/2" 21/2"
Yield Strength (Min. ksi) 60 to 21/2" 50 to 21/2" 80 90 100 50/100*
(Yield Point if incl.; 55 incl.; 45 available
designated YP) over 21/2" over 21/2"
ISG Plate
Thickness (Max. in.) 4 4 11/2 11/2 11/4 4**
Carbon .21 .21 .21 .21 .21 .07
Manganese .70/1.35 to .70/1.35 to 1.35 1.35 1.50 .40/.70
11/2" incl.; 11/2" incl.;
1.00/1.60 1.00/1.60
over 11/2" over 11/2"
Phosphorus .035 .035 .04 .04 .04 .015
Sulfur .04 .04 .05 .05 .05 .005
Silicon .50 .50 .40 .40 .40 .40
Chromium - - - - - .60/.90
Nickel - - - - - .70/1.00
Molybdenum - - - - - .15/.25
Copper .35 .35 .35 .35 .35 1.00/1.30
Other Elements .0005 Min. B .0005 Min. B .0005 Min. B .0005 Min. B .0005 Min. B .02/.06 Cb
CT
Heat Treatment Required Q&T N Q&T Q&T Q&T As rolled
&PHT,
N&PHT
or Q&PHT
* These minimum strength levels are available depending on heat treatment, thickness and toughness requirements.
Consult ISG Plate for specific available requirements.
** Consult ISG Plate for plates over thickness noted or additional chemistries.
Spartan Brochure
36
Duracorr®▲ Duracorr®▲ Duracorr®
SPECIFICATION Spartan II††
®
Spartan III††
®
Grade 40 Grade 50 300
Type of Steel Alloy Alloy Stainless Stainless Stainless
Requirements for Delivery A6, A20 A6, A20 A480 A480 A480
Tensile Strength (ksi) 90/110* 100/130* 66 Min. 70 Min. -
available available
Yield Strength (Min. ksi) 80/100* 90/120* 40 50 -
(Yield Point if available available
designated YP)
Spec. Thickness (Max. in.) - -
ISG Plate
Thickness (Max. in.) 4** 4** 4 4 4
Carbon .07 .07 .025 .025 .025
Manganese .75/1.15 .75/1.15 1.50 1.50 1.50
Phosphorus .015 .015 .040 .040 .040
Sulfur .005 .005 .015 .015 .015
Silicon .40 .40 .70 .70 .70
Chromium .45/.75 .45/.75 11.0/12.50 11.0/12.50 11.0/12.50
Nickel 1.50/2.00 3.35/3.65 1.00 1.00 1.00
Molybdenum .30/.55 .55/.65 .20/.30 .20/.30 .20/.30
Copper 1.00/1.30 1.15/1.75 - - -
Other Elements .02/.06 Cb .02/.06 Cb .030 N .030 N .030 N
Heat Treatment Required Q&PHT Q&PHT Tempered Tempered -
Remarks 233 Max. Surf. HB - 260/360 HB
▲ Also available as ASTM A1010.
* These minimum strength levels are available depending on heat treatment, thickness and toughness requirements.
Consult ISG Plate for specific available requirements.
** Consult ISG Plate for plates over thickness noted or additional chemistries.
Spartan Brochure
Duracorr Brochure
Duracorr 300 Brochure
37
BethStar® BethStar® BethStar® BethStar® V-Star® V-Star® T-Star®* T-Star®*

SPECIFICATION Grade 50 Grade 60 Grade 70 Grade 80 Grade 50 Grade 65 Grade 42 Grade 50
Type of Steel HSLA HSLA HSLA HSLA HSLA HSLA HSLA HSLA
Tensile Strength (ksi) 60 Min. 70 Min. 80 Min. 90 Min. 65 Min. 80 Min. 60 Min. 65 Min.
Yield Strength (Min. ksi) 50 60 70 80 50 65 42 YP 50YP
(Yield Point if
designated YP)
-
ISG Plate
Thickness (Max. in.) 2 1/2 11/2 1 3
/4 .875 1
/2 2 2
Carbon .10 .10 .10 .10 .10 .10 .12 .12
Manganese 1.65 1.65 1.65 1.65 1.45 1.50 1.35 1.35
Phosphorus .025 .025 .025 .025 .025 .025 .025 .025
Sulfur .010 .010 .010 .010 .010 .010 .018 .018
Silicon .35 .35 .35 .40 .25/.40 .25/.40 .40 .40
Vanadium .10 .10 .10 .10 .10 .10 .04 .04
Columbium .06 .06 .06 .06 - - - -
Titanium - - - - - - .02 .02
CE (IIW) .27/.31 .28/.32 .30/.34 .37/.41 .38 .38 .35 .35
PCM .16/.18 .16/.18 .16/.19 .21/.24 .22 .22 .20 .20
Remarks - - - - TMCP TMCP TMCP TMCP
PCM = C + (Mn+Cu+Cr)/20 + Mo /15 + V/10 + Si /30 + Ni /60 + 5B
* Also available as A572 Type 5.

▲ In the future the HY and HSLA Navy Alloy grades will be specified by the NAVSEA Technical Publication T9074-BD-GIB-010/0300
replacing the MIL-S Specifications. The information given here is from this new document.
▲▲ ISG Plate declared chemistries
BethStar Brochure
T-Star Brochure
Military Alloy Brochure
38
ISG PLATE MILITARY ALLOY STEELS
ISG PLATE HSLA 80▲ HSLA 100▲ HY 80▲ HY 100▲ MIL-A- MIL-A- MIL-A-
PROPRIETARY GRADES MIL-S- MIL-S- MIL-S- MIL-S- 46177 12560 46100
SPECIFICATION 24645A†† 24645A†† 16216-K 16216-K ▲▲ ▲▲ ▲▲
Tensile Strength (ksi) Report Report Report Report HB varies HB varies 477/534
info. only info. only info. only info. only per thickness per thickness HB
Yield Strength (Min. ksi) 80/110 to 1/4" 100/130 to 3/4" 80/100 to 3/4" 100/120 - - -
(Yield Point if excl.; 80/100 incl.; 100/125 incl.; 80/99.5
1
designated YP) /4" and over over 3/4" over 3/4"
Spec. Thickness (Max. in.) Cl. 1-1/2 Cl. 3-4 8 6 .249 8 2
Cl. 3-11/4
ISG Plate
Thickness (Max. in.) Cl. 1-< 5/16 Cl. 3-4 8 6 .249 8 2
Cl. 3-11/4
Carbon .06 .06 .10/.18 to 11/4" .10/.18 to 11/4" .18/.28 .18/.28 .22/.32
incl.; .13/.18 incl.; .14/.20 to 2.5" .20/.30
over 11/4" over 11/4" over 2.5"
Manganese .40/.70 .75/1.15 .10/.40 .10/.40 1.10/1.60 1.10/1.60 .70/1.00
to 2.5"
.15/.45
over 2.5"
Phosphorus .020 .020 .015 .015 .025. 015 .010
Sulfur .004 .004 .004 .004 .015 .015 .010
Silicon .40 .40 .15/.38. May .15/.38. May .20/.40 .20/.40 .35/.50
be .08 Min. be .08 Min
when vacuum when vacuum
carbon deoxidized carbon deoxidized
Chromium .60/.90 .45/.75 1.00/1.80 1.00/1.80 - 1.20/1.60 .40/.70

to 11/4" incl.; to 11/4" incl.; over 2.5"
1.40/1.80 1.40/1.80
over 11/4 -3" over 11/4 -3"
incl.; 1.50/ incl.; 1.50/
1.90 over 3" 1.90 over 3"
Nickel .70/1.00 1.50/2.00 2.00/3.25 to 2.25/3.50 to - 2.00/3.40 .80/1.30
to 1" incl.; 11/4" incl.; 11/4" incl.; over 2.5"
2.50/3.00 2.50/3.50 2.75/3.50
over 1"-15/8" over 11/4 -3" over 11/4 -3"
3.35/3.65 incl.; 3.00/ incl.; 3.00/
over 15/8" 3.50 over 3" 3.50 over 3"
Molybdenum .15/.25 .30/.55 to .20/.60 to .20/.60 to .40/.55 .40/.55 .50/.65
1" incl.; .45/.60 11/4"; .35/.60 11/4";.35/.60 to 2.5"
over 1"-15/8" over 11/4 -3" over 11/4 -3" .21/.36
.55/.65 incl.; .50/.65 incl.; .50/.65 over 2.5"
over 15/8" over 3" over 3"
Copper 1.00/1.30 1.00/1.30 .25 .25 - - -
to 15/8" incl. 15/8" incl.; 1.15/
1.75 over 15/8"
Other Elements .02/.06 Cb .02/.06 Cb .02 Ti/.03 V .02 Ti/.03 V - - -
CT Other residuals CT Other residuals Var. others Var. others
per specification per specification
Heat Treatment Required Cl. 1 as Cl. 3 Q&PHT Q&T Q&T Q&T Q&T Q&T
rolled&PHT
Cl. 3 Q&PHT
(See page 38 for footnotes)
39
ISG PLATE
ABRASION RESISTANT T-1® STEELS
A family of quenched and tempered alloy, fine grained
plate steels used primarily for abrasion resistance.
The grades vary in surface hardness, toughness, formability and weldability.*
T-1® T-1® T-1® T-1® Type A T-1® Type A T-1® Type A

Grade Grade Grade Grade Grade Grade
SPECIFICATION 321HB 340 HB 360 HB 321 HB 340 HB 360 HB
ISG Plate
Thickness (Max. in.) 2 1/2 2 11/2 11/4 1 3
/4
Carbon .10/.20 .10/.20 .10/.20 .12/.21 .12/.21 .12/.21
Manganese .60/1.00 .60/1.00 .60/1.00 .70/1.00 .70/1.00 .70/1.00
Phosphorus .035 .035 .035 .035 .035 .035
Sulfur .040 .040 .040 .040 .040 .040
Silicon .15/.35 .15/.35 .15/.35 .20/.35 .20/.35 .20/.35
Chromium .40/.65 .40/.65 .40/.65 .40/.65 .40/.65 .40/.65
Molybdenum .40/.60 .40/.60 .40/.60 .15/.25 .15/.25 .15/.25
Vanadium .03/.08 .03/.08 .03/.08 .03/.08 .03/.08 .03/.08
Boron .0005/.006 .0005/.006 .0005/.006 .0005/.005 .0005/.005 .0005/.005
Titanium - - - .01/.03 .01/.03 .01/.03
Copper .15/.50 .15/.50 .15/.50 - - -
Nickel .70/1.00 .70/1.00 .70/1.00 - - -
Heat Treatment Required Q&T Q&T Q&T Q&T Q&T Q&T
Surface Brinell Hardness (HB) 321 Min. 340 Min. 360 Min. 321 Min. 340 Min. 360 Min.
Melting Practice F/G/P F/G/P F/G/P F/G/P F/G/P F/G/P
Remarks - - - - - -
* ISG Plate Abrasion Resistant Steels should not be post-weld heat treated (stress-relieved) because such treatment will reduce
the hardness of the steel.
T-1 Brochure
40
CON TINUED ISG PLATE
ABRASION RESISTANT T-1® STEELS
T-1® Type B T-1® Type B T-1® Type B T-1® Type C T-1® Type C T-1® Type C
Grade Grade Grade Grade Grade Grade
SPECIFICATION 321 HB 340 HB 360 HB 321 HB 340 HB 360 HB
ISG Plate
Thickness (Max. in.) 2 11/2 1 6 2 11/2
Carbon .12/.21 .12/.21 .12/.21 .14/.21 .14/.21 .14/.21
Manganese .95/1.30 .95/1.30 .95/1.30 .95/1.30 .95/1.30 .95/1.30
Phosphorus .035 .035 .035 .035 .035 .035
Sulfur .040 .040 .040 .040 .040 .040
Silicon .20/.35 .20/.35 .20/.35 .15/.35 .15/.35 .15/.35
Chromium .40/.65 .40/.65 .40/.65 1.00/1.50 1.00/1.50 1.00/1.50
Molybdenum .20/.30 .20/.30 .20/.30 .40/.60 .40/.60 .40/.60
Vanadium .03/.08 .03/.08 .03/.08 .03/.08 .03/.08 .03/.08
Boron .0005/.005 .0005/.005 .0005/.005 - - -
Titanium - - - - - -
Copper - - - - - -
Nickel .30/.70 .30/.70 .30/.70 1.20/1.50 1.20/1.50 1.20/1.50
Heat Treatment Required Q&T Q&T Q&T Q&T Q&T Q&T
Surface Brinell Hardness (HB) 321 Min. 340 Min. 360 Min. 321 Min. 340 Min. 360 Min.
Melting Practice F/G/P F/G/P F/G/P F/G/P F/G/P F/G/P
Remarks - - - - - -
T-1 Brochure
41
ISG PLATE HARDWEAR® PREMIUM ABRASION RESISTANT ALLOY STEELS*
*Premium grades exhibiting through-hardening, improved forming and welding capabilities.
Grades with Hardness minimums not noted below are also available. Contact ISG Plate for details.
SPECIFICATION 400F 425F 450F 500F

Type of Steel Alloy Alloy Alloy Alloy
ISG Plate
Carbon .12/.16 .17/.21 .20/.25 .25/.31
Manganese 1.55 1.55 1.35 0.95
Phosphorus .025 .025 .025 .025
Sulfur .005 .005 .005 .005
Silicon .35/.55 .35/.55 .35/.55 .35/.55
Chromium .55 .55 .55 .75
Nickel 1.00 1.00 1.00 1.00
Molybdenum .55 .55 .65 .65
Vanadium - - - -
Boron .0005/.005 .0005/.005 .0005/.005 .0005/.005
Heat Treatment Required Q&T Q&T Q&T Q&T
Surface Brinell Hardness (HB) 360/444 401/477 429/495 460/544
Melting Practice F/G/P F/G/P F/G/P F/G/P
Remarks CT CT CT CT
Hardwear Brochure
ISG PLATE ABRASION RESISTANT STEELS**
**Standard grades intended for applications with minimum forming; often require preheat during welding.
SPECIFICATION AR200 AR235 ISG 400 ISG 450 ISG 500 ISG 550
Type of Steel Carbon Carbon Alloy Alloy Alloy Alloy
ISG Plate
Carbon .32/.36 .40/.50 .17 .26 .32 .35
Manganese .90/.130 .60/.90 1.55 1.35 .95 1.00
Phosphorus .040 .040 .025 .025 .025 .025
Sulfur .010 .050 .005 .005 .005 .005
Silicon .35 .10/.40 .55 .55 .55 .65
Chromium .25 - .55 .55 .75 1.00
Nickel .25 - 1.00 1.00 1.00 1.00
Molybdenum - - 55 .65 .65 .75
Copper .15/.45 - - - - -
Vanadium - - - - - -
Boron - - .0005/.005 .0005/.005 .0005/.005 .0005/.005
Heat Treatment Required - - Q&T Q&T Q&T Q&T
Surface Brinell Hardness (HB) ˜ 200 Nom. ˜ 235 Nom. 360/444 429/495 460/544 514/600
Melting Practice Killed Killed F/G/P F/G/P F/G/P F/G/P
Remarks - - CT CT CT CT
42
ISG PLATE MTD® STEELS
A prehardened family of alloy plate steels used primarily for mold,tool and die (MTD) applications.
SPECIFICATION MTD 1 MTD 2 MTD 3 MTD 4

ISG Plate
1
Thickness (Max. in.) /2 to 6 1/2 1
/2 to 12 3
/4 to 12 1
/2 to 61/2
Carbon .38/.46 .27/.33 .24/.35 .48/.53
Manganese .70/1.00 .90/1.30 .75/1.00 .75/1.10
Phosphorus .035 .035 .025 .035
Sulfur .040 .040 .005 .040
Silicon .15/.40 .15/.40 .15/.40 .15/.40
Chromium .80/1.15 .60/.90 .90/1.20 .80/1.10
Molybdenum .15/.25 .15/.25 .45/.65 .15/.25
Vanadium (Min.) .03 .02 .04 -
Other Elements - - - -
Heat Treatment Required N&T Q&T Q&T N&T
Surface Brinell Hardness (HB) 262/321 262/321 262/321 262/321
to 3" incl.; to 3" incl.;
241/321 over 241/321 over
3" to 6 1/2" incl. 3" to 6 1/2" incl.
Melting Practice F/G/P F/G/P F/G/P F/G/P
CT
MTD Brochure
ISG PLATE TOOL STEELS*

High Carbon, High Alloy Steels
SPECIFICATION A2 A8 Mod. D2 01 S5 S7
ISG Plate
Thickness (Max. in.) 6 1/2 2 1/4 6 1/2 6 1/2 2 1/4 6 1/2
Carbon .95/1.00 .48/.55 1.40/1.60 .85/1.00 .50/.65 .45/.55
Manganese .40/1.00 .20/.50 .60 1.00/1.40 .60/1.00 .20/.90
Phosphorus .030 .025 .030 .030 .030 .030
Sulfur .010 .003 .010 .010 .010 .010
Silicon .10/.50 .75/1.05 .10/.60 .10/.50 1.75/2.25 .20/1.00
Chromium 4.70/5.50 7.80/8.40 11.00/13.00 .40/.60 .10/.50 3.00/3.50
Molybdenum .90/1.40 1.25/1.75 .70/1.20 - .20/1.35 1.30/1.80
Vanadium .15/.50 .20/.55 .50/1.10 .30 .15/.35 .35
Tungsten - - - .40/.60 - -
Nickel ** ** ** ** ** **
Copper ** ** ** ** ** **
Hardness-HB Max. 235 241 235 212 235 223
in Annealed Condition
* Refer for size availability.
** Nickel and Copper .75% Max. unless otherwise specified.
Tool Steel Brochure
43
AASHTO* BRIDGE STEEL SPECIFICATIONS
*American Association of State Highway and Transportation Officials
Bridge steels can be ordered to the main AASHTO Specification M270, to individual AASHTO Steel
Specifications, and to ASTM A709. The following cross reference is provided to associate the grades.
See individual ASTM grades for chemical composition.
Similar Yield Tensile

AASHTO M270 ASTM A709 ASTM Strength Strength Plate Thicknesses
Grade* Grade Grade** (min., ksi) (min., ksi) Available
36 36 A36 36 58 To 4" incl.

50 50 A572 50 65 To 4" incl.
50W 50W A588 50 70 To 4" incl.
HPS 50W HPS 50W - 50 70 To 4" incl.
HPS 70W HPS 70W A852 70 85 To 4" incl.
100 100 A514 100 110 To 2 1/2" incl.
- - - 90 100 Over 2 1/2 to 4" incl.
100W 100W A514 100 110 To 2 1/2" incl.
- - - 90 100 Over 2 1/2 to 4" incl.
HPS 100W*** HPS 100W*** - 100 110 To 2 1/2" incl.
* Toughness testing mandatory unless otherwise specified.

** Similar in chemistry and tensile properties. Toughness testing optional per supplementary paragraphs.
*** HPS 100W is soon to be added to M270 and A709.
HPS 70W Brochure HPS 50W Brochure HPS 100W Brochure
ISG PLATE WEATHERING STEELS

Weathering steels contain modest amounts of alloy additives and resist atmospheric corrosion when used properly.
The following ASTM and ISG Plate grades are considered “weathering” per ASTM G101.
A242 (Mayari-R®) A588 (Mayari-R50®, Cor-Ten® B)
A514 Grades E, F, P, Q A709 Grades 50W, HPS-50W, HPS-70W, 100W, HPS-100W
A517 Grades E, F, P, Q A710 Grade A
A852 A736 Grade A
Spartan® Grades I, II, III, IV, V A871 (Mayari-R60®)
Weathering Steels Brochure
44
CROSS REFERENCE OF POPULAR INTERNATIONAL SPECIFICATIONS
Popular Chemistry Only Grades
AISI (USA) Material No. DIN (German) BS (British) JIS (Japanese)

1020 1.0402 17200-C22 970 Pt. 1 040M20 G4051-S20C
1030 1.0503 17200-C30 970 Pt. 1 080M30 G4051-S30C
1040 1.0511 17200-C40 970 Pt. 1 080M40 G4051-S40C
1045 1.0503 17200-C45 970 Pt. 1 080M46 G4051-S45C
4130 1.7220 17200-34CrMo4 970 Pt. 1 708A30 G4105-SCM 430
4140 1.7225 17200-42CrMo4 970 Pt. 1 708M40 G4105-SCM 440
4340 1.6565 40NiCrMo6 - G4103-SNCM 439
Popular Structural Grades
ASTM (USA) Material No. DIN (German) BS (British) JIS (Japanese)

A36 1.0044 17100 St 44-2 4360 43A G3101-SS 400
A572* - - 4360 50B G3106-SM 490, 520, 570
A588 - - - G3114-SMA 490
A633* 1.0570 17100 St 52-3 - G3106-SM 520
1.0505 17102 StE 315 - G3106-SM 490
1.0562 17102 StE 355 4360 50D, 50E G3106-SM 520
1.8902 17102 StE 420 4360 55F G3106-SM 570
A514* - - - G3128-SHY 685,
685N, 685NS
Popular Pressure Vessel Grades
ASTM (USA) Material No. DIN (German) BS (British) JIS (Japanese)

A285* 1.0345 17155 HI 1501-151, 360, 400 G3115-SPV 235
A516* 1.0425 17155 HII 1501-224, 360, 400, G3118-SGV 410,
1.0481 17155 17MN4 430, 490 450, 480
A537* 1.0473 17155 19MN6 1501-224, 490 G3115 SPV 355
A387* 1.7335 17155 13CRMO4 4 1501-620, 621 G4109-SCMV 2, 3
1.7380 17155 10CRMO9 10 1501-622 G4109-SCMV 4
A553 1.5662 17280 8XNi9 - -
Exact substitution is often not possible; review specification of interest before ordering. ISG Plate will accept
orders to popular specifications independent of origin.
* Various Grades and/or Classes available.
45
ISG PLATE COATESVILLE/CONSHOHOCKEN PLANTS
TABLE CARBON PLATE STEEL SIZES MAXIMUM DIMENSIONS
A INCHES
Width
Thickness 48 54 60 66 72 78 84 90 96 102 108 114 120
;;;
;;;
;;;
3/16 720 720 720 720 720 720 720 720 720
1/4 720 720 720 720 720 720 720 720 720 .INQUIRE.
5/16 720 720 720 720 720 720 720 720 720
3/8 1,030 1,030 1,030 1,030 1,030 1,030 1,030 1,030 1,030 800 800 680 680
7/16 1,030 1,030 1,030 1,030 1,030 1,030 1,030 1,030 1,030 1,000 1,000 680 680
1/2 1,030 1,030 1,030 1,030 1,030 1,030 1,030 1,030 1,030 1,000 1,000 680 680
9/16 1,030 1,030 1,030 1,120 1,250 1,250 1,250 1,250 1,250 1,120 1,120 680 680
5/8 1,440 1,480 1,500 1,500 1,525 1,525 1,525 1,480 1,400 960 960 680 680
11/16 1,440 1,480 1,500 1,500 1,525 1,525 1,525 1,350 1,350 960 960 680 680
3/4 1,440 1,480 1,500 1,500 1,525 1,525 1,525 1,350 1,350 1,030 980 680 680
7/8 1,440 1,480 1,500 1,500 1,525 1,525 1,525 1,340 1,250 1,030 980 680 680
1 1,440 1,480 1,500 1,500 1,525 1,525 1,525 1,350 1,350 1,030 980 680 680
1-1/8 1,440 1,440 1,440 1,440 1,440 1,440 1,400 1,290 1,200 945 890 680 680
1-1/4 1,440 1,320 1,440 1,440 1,440 1,360 1,350 1,350 1,350 1,090 790 680 680
1-3/8 1,320 1,190 1,440 1,440 1,440 1,350 1,350 1,350 1,350 1,055 720 680 680
1-1/2 1,230 1,160 1,440 1,350 1,350 1,350 1,350 1,350 1,350 1,035 720 680 680
1-3/4 1,050 925 1,220 1,120 1,350 1,350 1,270 1,270 1,270 995 720 680 680
2 905 800 1,060 960 1,300 1,200 1,120 1,220 1,140 930 720 680 680
2-1/4 790 725 930 870 1,160 1,080 980 1,090 1,010 865 720 680 680
2-1/2 725 680 830 1,090 1,180 1,100 1,310 1,220 1,140 930 720 680 680
2-3/4 665 720 750 990 1,070 1,010 1,180 1,110 1,030 720 720 680 680
3 610 720 710 900 970 910 1,080 1,020 940 720 720 680 680
3-1/4 570 635 670 830 900 840 980 920 870 635 635 635 635
3-1/2 530 635 620 770 830 770 920 860 800 635 635 620 600
3-3/4 490 625 580 720 770 720 860 800 740 635 610 600 600
4 465 590 540 720 720 720 800 750 685 605 600 600 600
Length
4-1/2 415 525 495 630 635 635 635 635 635 600 600 600 600
5 365 470 445 565 620 635 635 635 625 600 600 600 581
5-1/2 330 425 405 515 565 635 635 605 570 600 587 556 528
6 305 385 365 470 515 620 595 550 515 569 538 509 484
6-1/2 275 355 335 435 470 565 550 505 470 526 496 470 447
7 255 330 310 400 435 525 510 465 435 488 461 437 415
7-1/2 240 305 285 375 405 485 470 430 400 455 430 407 387
8 225 280 265 350 380 455 440 410 375 427 403 382 363
9 195 250 235 310 335 405 390 360 340 379 358 339 322
10 175 225 215 275 300 360 350 325 310 341 322 301 286
11 155 200 190 250 265 325 320 290 275 306 289 274 260
12 145 180 175 220 235 300 285 265 260 281 265 251 258
13 133 169 163 205 215 275 260 240 225 259 245 232 217
14 123 157 150 190 202 255 235 220 205 240 224 212 201
15 114 146 140 176 187 233 218 205 195 221 209 198 188
16 136 131 166 175 216 205 160 160 160 136 129
17 128 123 156 165 200 195 160 160 160 128 116
18 120 116 148 155 190 185 160 160 160 120
19 113 110 140 146 180 176 160 160 160 110
20 107 104 133 140 170 167 160 160 160
21 102 99 126 133 164 159 149 139 153
22 96 92 119 126 158 152 142 132 146
23 92 89 113 119 152 145 135 126 140
24 88 85 108 113 146 138 128 119 134
25 84 83 104 108 140 132 124 114 129
26 105 115 110 119 111 123
27 101 111 106 115 107 118
28 99 108 103 111 102 114
29 95 105 100 107 100 110
30 93 102 96 104 96 106
TABLE A, continued on next page.
NOTE: The lengths in the shaded areas from 5/8 inches through 2-1/4 inches thick apply to mild carbon grades such as ASTM A830 Grades 1006 through 1023, A36, A131 Grade A,
A283 and A285. For grades other than these, the maximum length available is 80% of the length shown unless otherwise approved.
TABLE CARBON PLATE STEEL SIZES MAXIMUM DIMENSIONS
A CONTINUED INCHES
Width
Thickness 126 132 138 144 150 156 162 168 174 180 186 192 195
;; ;
3/16
1/4
;; ;;;;; .INQUIRE.
;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;
5/16
;; ;;
;; ;;
;; ;;
3/8 624 624
7/16 624 624
.INQUIRE.
1/2 624 624
9/16 624 624
5/8 624 624 550 550 550 468 486 504 348 360 372
11/16 624 624 550 550 550 468 486 504 348 360 372
3/4 624 624 550 550 550 468 486 504 348 360 372
7/8 624 624 600 600 600 468 486 504 348 360 372
1 624 624 600 600 600 468 486 504 348 360 372
1-1/8 624 624 600 600 600 600 600 600 550 550 450
1-1/4 624 624 600 600 600 600 600 600 550 550 435
1-3/8 624 600 600 600 600 600 600 600 550 550 395
1-1/2 624 600 600 600 600 600 600 600 550 550 360
1-3/4 624 600 600 600 600 600 600 600 550 550 360
2 624 600 600 600 600 600 600 600 550 550 270
Length
2-1/4 624 600 600 600 600 600 600 600 550 550 240
2-1/2 624 600 600 600 600 600 600 600 550 495 215
2-3/4 624 600 600 600 600 600 600 600 550 450 195
3 624 600 600 600 600 600 600 600 550 415 195
3-1/4 605 600 600 600 600 600 600 600 550 380 195
3-1/2 600 600 600 600 600 600 600 590 550 355 195
3-3/4 600 600 600 600 600 600 575 550 526 330
4 600 600 600 600 585 562 542 522 494 310
4-1/2 600 591 565 542 520 500 481 464 439 275
5 557 532 508 487 468 450 433 418 395 245
5-1/2 506 483 462 443 425 409 394 380 359 225
6 464 443 424 406 390 375 361 348 329 205
6-1/2 428 409 391 375 360 346 333 321 299
7 398 380 363 348 334 321 309 298 278
7-1/2 371 354 339 325 312 300 289 278 259
8 348 332 316 304 292 281 271 261 243
9 307 293 280 271 260 250 240 232 215
10 276 264 252 243 234 223 215 207 193
11 251 240 226 220 211 203 195 188
12 227 217 207 201 193 186 179
13 210 200 191 186 178 172
14 195 186 178 173 161
15 182 173 161 157
Please inquire with ISG Plate for:

1. Additional sizes not shown on this card and sizes in cross-hatched areas.
2. Maximum lengths available on plates with thicknesses and/or widths between the increments shown.
3. Plates 4 inches thick and less requiring heat treatment where lengths exceed 540 inches and plates over 4 inches that exceed 480 inches long.
4. Plate widths under 48 inches when number of pieces and lengths can be nested and cut within above size card.
5. HSLA Bridge Plate (e.g. A709 Grades 50 and 50W) which are both over 700 inches long and over 25,000 pounds pattern weight.
6. Plates over 15 inches when 1.5 times ASTM A6 flatness tolerances is not acceptable.
7. Plates of 85,000 pounds pattern weight and greater.
8. Plates over 600 inches when not produced as mill edge plate.
9. Nested patterns from plates 6 inches thick and greater.
TABLE ALLOY PLATE STEEL SIZES MAXIMUM DIMENSIONS
B INCHES
Width
Thickness 48 54 60 66 72 78 84 90 96 102 108 114 120
;;;
;;;
;;;
3/16 625 720 720 648 648 648 600 480 480
1/4 720 720 720 720 600 600 600 600 600 .INQUIRE.
5/16 720 720 720 800 800 800 720 720 648
3/8 720 720 720 960 960 960 960 960 960 960 960 680 680
7/16 720 720 720 960 960 960 960 960 960 960 960 680 680
1/2 850 850 850 960 960 960 960 960 960 960 960 680 680
9/16 850 850 850 960 960 960 960 960 960 960 960 680 680
5/8 960 960 960 960 960 960 960 960 960 955 900 680 680
11/16 960 960 960 960 960 960 960 960 915 865 815 680 680
3/4 960 960 960 1,030 1,030 1,030 1,030 1,030 1,030 1,030 980 680 680
7/8 960 960 960 1,030 1,030 1,030 1,030 1,030 1,030 1,030 980 680 680
1 960 960 960 950 1,030 1,030 1,030 1,030 1,030 1,030 980 680 680
1-1/8 930 860 850 830 1,030 1,030 1,030 1,030 995 945 890 680 680
1-1/4 835 775 750 750 1,030 1,030 1,025 955 895 840 790 680 680
1-3/8 740 720 720 720 1,030 980 930 855 800 760 720 680 680
1-1/2 720 720 720 720 975 900 840 785 735 720 720 680 680
1-3/4 720 720 720 720 820 760 720 720 720 720 720 680 680
2 720 720 720 720 720 720 720 720 720 720 720 680 680
Length
2-1/4 720 720 720 720 720 720 720 720 720 720 720 680 680
2-1/2 720 720 720 720 720 720 720 720 720 720 720 680 680
2-3/4 665 720 720 720 720 720 720 720 720 720 720 680 680
3 610 720 720 720 720 720 720 720 720 720 710 670 640
3-1/4 595 635 635 635 635 635 635 635 635 635 635 635 620
3-1/2 550 635 635 635 635 635 635 635 635 635 635 605 575
3-3/4 515 635 620 635 635 635 635 635 635 635 595 565 535
4 480 635 580 635 635 635 635 635 635 605 600 600 600
4-1/2 430 560 515 635 635 635 635 610 600 600 600 600 600
5 380 505 460 555 635 635 600 600 575 600 600 600 581
5-1/2 350 460 420 505 635 600 595 555 520 600 587 556 528
6 315 415 380 460 635 585 545 505 475 569 538 509 484
6-1/2 290 390 355 425 510 540 500 470 440 526 496 470 447
7 270 360 325 395 470 500 465 430 405 488 461 437 415
7-1/2 250 335 300 370 440 470 430 405 380 455 430 407 387
8 235 310 285 345 410 435 405 374 355 427 403 382 363
9 210 270 250 305 370 385 360 335 315 379 358 339 322
10 190 240 220 275 325 350 325 300 280 341 322 301 286
11 170 225 205 250 295 315 290 270 255 306 289 274 260
12 155 205 185 230 270 240 265 250 235 281 265 251 238
13 145 185 170 210 250 265 245 225 215 259 245 232 217
14 135 170 160 195 230 245 225 210 195 240 224 212 201
15 125 160 145 180 215 225 210 195 185 221 209 198 188
TABLE B, continued on next page.
TABLE ALLOY PLATE STEEL SIZES MAXIMUM DIMENSIONS
B CONTINUED INCHES
Width
Thickness 126 132 138 144 150 156 162 168 174 180 186 192 195
;; ;
3/16
1/4
5/16
3/8
;;; ;;; .INQUIRE.
624 624
;; ;;
;; ;;;;;;;;;;;
7/16 624 624
1/2 624 624
;; ;;;;;;;; ;
9/16 624 624 .INQUIRE.
5/8 624 624
11/16 624 624 550 550 550 550 540
;; ;;;;;;;;
;; ;;;;;;;;
3/4 624 624 550 550 550 550 550 550 550
7/8 624 624 600 600 600 600 600 600 550
1 624 624 600 600 600 600 600 600 550
1-1/8 624 624 600 600 600 600 600 560 540
1-1/4 624 624 600 600 600 600 600 505 485
1-3/8 624 600 600 600 600 600 600 455 440
1-1/2 624 600 600 600 600 600 600 420 405
1-3/4 624 600 600 600 600 600 600 355 340
2 624 600 600 600 600 600 600 310 295 .INQUIRE.
Length
2-1/4 624 600 600 600 600 600 600 270 260
2-1/2 624 600 600 600 600 590 550 245 235
2-3/4 624 600 600 585 560 540 500 220 210
3 615 585 560 535 515 495 460 200 195
3-1/4 595 540 515 495 475 455 425
3-1/2 550 500 480 460 440 420 395
3-3/4 515 465 445 425 410 380 365
4 600 600 600 600 585 562 542
4-1/2 600 591 565 542 520 500 481
5 557 532 509 487 468 450 433
5-1/2 506 483 462 443 425 409 394
6 464 443 424 406 390 375 361
6-1/2 428 409 391 375 360 346 333
7 398 380 363 348 334 321 309
7-1/2 371 354 339 325 312 300 289
8 348 332 316 304 292 281 271
9 307 293 280 271 260 250 240
10 276 264 252 243 234 223 215
11 251 240 226 220 211 203 195
12
13
14
15

TABLE CARBON PLATE STEEL SIZES MAXIMUM PIECE WEIGHT IN POUNDS
C INCHES
Width
Thickness 48 54 60 66 72 78 84 90 96 102 108 114 120
;;;
;;;
;;;
3/16 1,838 2,067 2,297 2,527 2,757 2,986 3,216 3,446 3,675
1/4 2,450 2,757 3,063 3,369 3,675 3,982 4,288 4,594 4,901 .INQUIRE.
5/16 3,063 3,446 3,829 4,211 4,594 4,977 5,360 5,743 6,126
3/8 5,258 5,915 6,572 7,230 7,887 8,544 9,201 9,859 10,516 8,678 9,189 8,244 8,678
7/16 6,134 6,901 7,668 8,435 9,201 9,968 10,735 11,502 12,269 12,656 13,400 9,618 10,125
1/2 7,011 7,887 8,763 9,640 10,516 11,392 12,269 13,145 14,021 14,464 15,314 10,992 11,571
9/16 7,887 8,873 9,859 11,792 14,357 15,554 16,750 17,947 19,143 18,224 19,296 12,366 13,017
5/8 12,252 14,166 15,953 17,548 19,462 21,084 22,706 23,610 23,822 17,356 18,377 13,740 14,464
11/16 13,477 15,582 17,548 19,303 21,408 23,192 24,976 23,689 25,269 19,092 20,215 15,114 15,910
3/4 14,702 16,999 19,143 21,057 23,354 25,301 27,247 25,843 27,566 22,346 22,512 16,489 17,356
7/8 17,152 19,832 22,334 24,567 27,247 29,517 31,788 29,927 29,778 26,071 26,264 19,237 20,249
1 19,602 22,665 25,524 28,076 31,139 33,734 36,329 34,457 36,755 29,795 30,016 21,985 23,142
1-1/8 22,053 24,809 27,566 30,323 33,079 35,836 37,520 37,042 36,755 30,753 30,667 24,733 26,034
1-1/4 24,503 25,269 30,629 33,692 36,755 37,605 40,200 43,072 45,943 39,413 30,246 27,481 28,927
1-3/8 24,707 25,058 33,692 37,061 40,430 41,062 44,220 47,379 50,538 41,963 30,323 30,229 31,820
1-1/2 25,116 26,647 36,755 37,903 41,349 44,795 48,240 51,686 55,132 44,909 33,079 32,977 34,713
1-3/4 25,014 24,790 36,329 36,686 48,240 52,260 52,945 56,727 60,509 50,369 38,592 38,473 40,498
2 24,639 24,503 36,074 35,938 53,090 53,090 53,362 62,279 62,074 53,805 44,105 43,969 46,284
2-1/4 24,197 24,982 35,606 36,640 53,294 53,754 52,528 62,598 61,870 56,300 49,619 49,466 52,069
2-1/2 24,673 26,034 35,308 51,005 60,237 60,832 78,018 77,848 77,593 67,256 55,132 54,962 57,854
2-3/4 24,894 30,323 35,096 50,959 60,083 61,441 77,304 77,912 77,117 57,276 60,645 60,458 63,640
3 24,911 33,079 36,244 50,538 59,420 60,390 77,185 78,103 76,776 62,483 66,158 65,954 69,425
3-1/4 25,218 31,605 37,052 50,491 59,726 60,390 75,874 76,317 76,980 59,699 63,210 66,722 70,234
3-1/2 25,252 34,036 36,925 50,444 59,318 59,616 76,708 76,827 76,232 64,291 68,073 70,157 71,467
3-3/4 25,014 35,893 37,010 50,538 58,960 59,726 76,827 76,572 75,551 68,883 70,063 72,743 76,572
4 25,320 36,142 36,755 53,907 58,807 63,708 76,232 76,572 74,598 70,004 73,509 77,593 81,677
Length
4-1/2 25,422 36,180 37,903 53,064 58,348 63,210 68,073 72,935 77,797 78,103 82,698 87,292 91,886
5 24,843 35,989 37,861 52,877 63,300 70,234 75,636 81,039 85,080 86,782 91,886 96,991 98,863
5-1/2 24,707 35,797 37,903 53,018 63,453 77,257 83,200 84,931 85,352 95,460 98,885 98,866 98,829
6 24,911 35,376 37,265 52,784 63,095 82,289 85,046 84,229 84,127 98,757 98,870 98,737 98,829
6-1/2 24,333 35,338 37,052 52,924 62,381 81,239 85,165 83,783 83,174 98,902 98,747 98,769 98,880
7 24,299 35,376 36,925 52,409 62,176 81,294 85,046 83,081 82,902 98,815 98,839 98,899 98,863
7-1/2 24,503 35,032 36,372 52,643 62,023 80,464 83,974 82,315 81,677 98,714 98,778 98,689 98,778
8 24,503 34,304 36,074 52,409 62,074 80,520 83,855 83,719 81,677 98,815 98,747 98,802 98,829
9 23,890 34,457 35,989 52,222 61,564 80,630 83,617 82,698 83,310 98,671 98,686 98,640 98,625
10 23,822 34,457 36,584 51,473 61,258 79,635 83,378 82,953 84,399 98,642 98,625 97,315 97,332
11 23,210 33,692 35,563 51,473 59,522 79,082 83,855 81,422 82,357 97,369 97,369 97,444 97,332
12 23,686 33,079 35,734 49,414 57,582 79,635 81,473 81,166 84,944 97,543 97,400 97,379 97,195
13 23,537 33,646 36,057 49,882 57,072 79,082 80,520 79,635 79,635 97,398 97,553 97,508 96,004
14 23,441 33,661 35,734 49,789 57,745 78,971 78,376 78,614 78,137 97,195 96,052 95,957 95,766
15 23,278 33,539 35,734 49,414 57,276 77,312 77,899 78,486 79,635 95,894 96,021 96,021 95,970
16 0 33,324 35,666 49,714 57,174 76,449 78,137 65,341 69,698 74,054 66,648 66,730
17 0 33,324 35,580 49,639 57,276 75,211 78,971 69,425 74,054 78,682 66,648 63,756
18 0 33,079 35,529 49,864 56,970 75,653 79,329 73,509 78,410 83,310 66,158
19 0 32,880 35,563 49,789 56,643 75,653 79,662 77,593 82,766 87,939 64,014
20 0 32,773 35,393 49,789 57,174 75,211 79,567 81,677 87,122 92,567
21 0 32,803 35,376 49,527 57,031 76,184 79,543 79,865 79,472 92,943
22 0 32,344 34,440 49,003 56,602 76,892 79,662 79,737 79,063 92,914
23 0 32,405 34,832 48,647 55,887 77,334 79,448 79,252 78,900 93,146
24 0 32,344 34,713 48,516 55,377 77,511 78,900 78,410 77,756 93,030
25 0 32,160 35,308 48,666 55,132 77,423 78,614 79,124 77,593 93,290
26 0 0 0 51,099 61,053 63,265 73,707 73,662 87,067
27 0 0 0 51,043 61,196 63,310 73,969 73,739 86,741
28 0 0 0 51,885 61,748 63,796 74,040 72,897 86,904
29 0 0 0 51,567 62,176 64,150 73,921 74,020 86,850
30 0 0 0 52,222 62,483 63,708 74,326 73,509 86,577
TABLE C, continued on next page.
TABLE CARBON PLATE STEEL SIZES MAXIMUM PIECE WEIGHT IN POUNDS
C CONTINUED INCHES
Width
Thickness 126 132 138 144 150 156 162 168 174 180 186 192 195
;; ;
3/16
1/4
;; ;;;;; .INQUIRE.
;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;
5/16
;; ;;
;; ;;
;; ;;
3/8 8,362 8,760
7/16 9,755 10,220
.INQUIRE.
1/2 11,149 11,680
9/16 12,542 13,140
5/8 13,936 14,600 13,453 14,038 14,623 12,941 13,955 15,008 10,733 11,486 12,264
11/16 15,330 16,060 14,799 15,442 16,085 14,235 15,351 16,509 11,806 12,634 13,491
3/4 16,723 17,520 16,144 16,846 17,548 15,529 16,746 18,010 12,879 13,783 14,717
7/8 19,511 20,440 20,547 21,440 22,334 18,117 19,537 21,011 15,026 16,080 17,170
1 22,298 23,360 23,482 24,503 25,524 20,705 22,328 24,013 17,173 18,377 19,623
1-1/8 25,085 26,280 26,417 27,566 28,715 29,863 31,012 32,160 30,533 31,586 26,704
1-1/4 27,872 29,199 29,353 30,629 31,905 33,181 34,457 35,734 33,926 35,096 28,683
1-3/8 30,659 30,884 32,288 33,692 35,096 36,499 37,903 39,307 37,318 38,605 28,650
1-1/2 33,447 33,692 35,223 36,755 38,286 39,817 41,349 42,880 40,711 42,115 28,485
1-3/4 39,021 39,307 41,094 42,880 44,667 46,454 48,240 50,027 47,496 49,134 33,232
2 44,596 44,922 46,964 49,006 51,048 53,090 55,132 57,174 54,281 56,153 28,485
Length
2-1/4 50,170 50,538 52,835 55,132 57,429 59,726 62,023 64,320 61,066 63,172 28,485
2-1/2 55,744 56,153 58,705 61,258 63,810 66,362 68,915 71,467 67,851 63,172 28,353
2-3/4 61,319 61,768 64,576 67,383 70,191 72,999 75,806 78,614 74,636 63,172 28,287
3 66,893 67,383 70,446 73,509 76,572 79,635 82,698 85,761 81,422 63,555 30,859
3-1/4 70,261 72,999 76,317 79,635 82,953 86,271 89,589 92,907 88,207 63,044 33,430
3-1/2 75,041 78,614 82,187 85,761 89,334 92,907 96,481 98,387 94,992 63,427 36,002
3-3/4 80,401 84,229 88,058 91,886 95,715 99,544 99,065 98,267 97,336 63,172
4 85,761 89,844 93,928 98,012 99,544 99,455 99,605 99,482 97,508 63,300
4-1/2 96,481 99,559 99,505 99,605 99,544 99,544 99,444 99,482 97,484 63,172
5 99,518 99,578 99,407 99,442 99,544 99,544 99,467 99,578 97,459 62,534
5-1/2 99,447 99,447 99,447 99,503 99,437 99,521 99,559 99,578 97,434 63,172
6 99,482 99,503 99,564 99,482 99,544 99,544 99,513 99,482 97,410 62,789
6-1/2 99,411 99,521 99,466 99,544 99,544 99,499 99,444 99,411 95,905
7 99,554 99,578 99,447 99,482 99,459 99,411 99,375 99,387 96,028
7-1/2 99,429 99,390 99,505 99,544 99,544 99,544 99,582 99,339 95,855
8 99,482 99,428 98,938 99,319 99,373 99,455 99,605 99,482 95,929
9 98,732 98,717 98,625 99,605 99,544 99,544 99,237 99,482 95,485
10 98,625 98,829 98,625 99,237 99,544 98,659 98,778 98,625 95,239
11 98,660 98,829 97,294 98,829 98,735 98,791 98,548 98,529
12 97,338 97,481 97,216 98,502 98,523 98,747 98,686
13 97,553 97,332 97,177 98,747 98,438 98,924
14 97,553 97,481 97,529 98,911 95,885
15 97,553 97,144 94,515 96,174

5. HSLA Bridge Plate (e.g. A709 Grades 50 and 50W) which are both over 700 inches long and over 25,000 pounds pattern weight.
7. Plates of 85,000 pounds pattern weight and greater.
TABLE ALLOY PLATE STEEL SIZES MAXIMUM PIECE WEIGHT IN POUNDS
D INCHES
Width
Thickness 48 54 60 66 72 78 84 90 96 102 108 114 120
;;;
;;;
;;;
3/16 1,595 2,067 2,297 2,274 2,481 2,688 2,680 2,297 2,450
1/4 2,450 2,757 3,063 3,369 3,063 3,318 3,573 3,829 4,084 .INQUIRE.
5/16 3,063 3,446 3,829 4,679 5,105 5,530 5,360 5,743 5,513
3/8 3,675 4,135 4,594 6,738 7,351 7,963 8,576 9,189 9,801 10,414 11,026 8,244 8,678
7/16 4,288 4,824 5,360 7,861 8,576 9,291 10,005 10,720 11,435 12,149 12,864 9,618 10,125
1/2 5,785 6,509 7,232 8,984 9,801 10,618 11,435 12,252 13,068 13,885 14,702 10,992 11,571
9/16 6,509 7,322 8,136 10,108 11,026 11,945 12,864 13,783 14,702 15,621 16,540 12,366 13,017
5/8 8,168 9,189 10,210 11,231 12,252 13,272 14,293 15,314 16,335 17,266 17,229 13,740 14,464
11/16 8,984 10,108 11,231 12,354 13,477 14,600 15,723 16,846 17,127 17,203 17,162 15,114 15,910
3/4 9,801 11,026 12,252 14,459 15,774 17,088 18,403 19,717 21,032 22,346 22,512 16,489 17,356
7/8 11,435 12,864 14,293 16,869 18,403 19,936 21,470 23,004 24,537 26,071 26,264 19,237 20,249
1 13,068 14,702 16,335 17,782 21,032 22,784 24,537 26,290 28,042 29,795 30,016 21,985 23,142
1-1/8 14,242 14,817 16,272 17,478 23,661 25,632 27,604 29,576 30,476 30,753 30,667 24,733 26,034
1-1/4 14,208 14,836 15,953 17,548 26,290 28,481 30,522 30,469 30,459 30,374 30,246 27,481 28,927
1-3/8 13,851 15,161 16,846 18,530 28,919 29,808 30,463 30,007 29,948 30,229 30,323 30,229 31,820
1-1/2 14,702 16,540 18,377 20,215 29,863 29,863 30,016 30,055 30,016 31,241 33,079 32,977 34,713
1-3/4 17,152 19,296 21,440 23,584 29,302 29,421 30,016 32,160 34,304 36,448 38,592 38,473 40,498
2 19,602 22,053 24,503 26,953 29,404 31,854 34,304 36,755 39,205 41,655 44,105 43,969 46,284
2-1/4 22,053 24,809 27,566 30,323 33,079 35,836 38,592 41,349 44,105 46,862 49,619 49,466 52,069
Length
2-1/2 24,503 27,566 30,629 33,692 36,755 39,817 42,880 45,943 49,006 52,069 55,132 54,962 57,854
2-3/4 24,894 30,323 33,692 37,061 40,430 43,799 47,168 50,538 53,907 57,276 60,645 60,458 63,640
3 24,911 33,079 36,755 40,430 44,105 47,781 51,456 55,132 58,807 62,483 65,239 64,984 65,341
3-1/4 26,324 31,605 35,117 38,628 42,140 45,652 49,163 52,675 56,187 59,699 63,210 66,722 68,574
3-1/2 26,205 34,036 37,818 41,600 45,382 49,163 52,945 56,727 60,509 64,291 68,073 68,460 68,489
3-3/4 26,290 36,467 39,562 44,571 48,623 52,675 56,727 60,779 64,831 68,883 68,341 68,500 68,277
4 26,137 38,899 39,477 47,543 51,865 56,187 60,509 64,831 69,153 70,004 73,509 77,593 81,677
4-1/2 26,341 38,592 39,435 53,486 58,348 63,210 68,073 70,063 73,509 78,103 82,698 87,292 91,886
5 25,864 38,669 39,137 51,941 64,831 70,234 71,467 76,572 78,274 86,782 91,886 96,991 98,863
5-1/2 26,205 38,745 39,307 51,988 71,314 72,999 77,959 77,912 77,865 95,460 98,885 98,866 98,829
6 25,728 38,133 38,796 51,661 77,797 77,644 77,899 77,338 77,593 98,757 98,870 98,737 98,829
6-1/2 25,660 38,822 39,264 51,707 67,690 77,644 77,423 77,976 77,865 98,902 98,747 98,769 98,880
7 25,728 38,592 38,711 51,754 67,179 77,423 77,542 76,827 77,185 98,815 98,839 98,899 98,863
7-1/2 25,524 38,477 38,286 51,941 67,383 77,976 76,827 77,529 77,593 98,714 98,778 98,689 98,778
8 25,592 37,980 38,796 51,661 66,975 76,980 77,185 76,368 77,321 98,815 98,747 98,802 98,829
9 25,728 37,214 38,286 51,380 67,996 76,649 77,185 76,955 77,185 98,671 98,686 98,640 98,625
10 25,864 36,755 37,435 51,473 66,362 77,423 77,423 76,572 76,232 98,642 98,625 97,315 97,332
11 25,456 37,903 38,371 51,473 66,260 76,649 75,993 75,806 76,368 97,369 97,369 97,444 97,332
12 25,320 37,673 37,776 51,661 66,158 63,708 75,755 76,572 76,776 97,543 97,400 97,379 97,195
13 25,660 36,831 37,605 51,099 66,362 76,206 75,874 74,658 76,096 97,398 97,553 97,508 96,004
14 25,728 36,448 38,116 51,099 65,750 75,874 75,041 75,041 74,326 97,195 96,052 95,957 95,766
15 25,524 36,755 37,010 50,538 65,852 74,658 75,041 74,658 75,551 95,894 96,021 96,021 95,970
TABLE D, continued on next page.
TABLE ALLOY PLATE STEEL SIZES MAXIMUM PIECE WEIGHT IN POUNDS
D CONTINUED INCHES
Width
Thickness 126 132 138 144 150 156 162 168 174 180 186 192 195
;; ;
3/16
1/4
5/16
3/8
;;; ;;; .INQUIRE.
8,362 8,760
;;;;
;; ;;;;;;;;;;;
7/16 9,755 10,220
1/2 11,149 11,680
;; ;;;;;;;; ;
9/16 12,542 13,140 .INQUIRE.
5/8 13,936 14,600
11/16 15,330 16,060 14,799 15,442 16,085 16,729 17,056
;; ;;;;;;;;
;; ;;;;;;;;
3/4 16,723 17,520 16,144 16,846 17,548 18,250 18,952 19,653 20,355
7/8 19,511 20,440 20,547 21,440 22,334 23,227 24,120 25,014 23,748
1 22,298 23,360 23,482 24,503 25,524 26,545 27,566 28,587 27,141
1-1/8 25,085 26,280 26,417 27,566 28,715 29,863 31,012 30,016 29,978
1-1/4 27,872 29,199 29,353 30,629 31,905 33,181 34,457 30,076 29,916
1-3/8 30,659 30,884 32,288 33,692 35,096 36,499 37,903 29,808 29,855
1-1/2 33,447 33,692 35,223 36,755 38,286 39,817 41,349 30,016 29,978
1-3/4 39,021 39,307 41,094 42,880 44,667 46,454 48,240 29,599 29,361
2 44,596 44,922 46,964 49,006 51,048 53,090 55,132 29,540 29,114 .INQUIRE.
Length
2-1/4 50,170 50,538 52,835 55,132 57,429 59,726 62,023 28,944 28,868
2-1/2 55,744 56,153 58,705 61,258 63,810 65,256 63,172 29,182 28,991
2-3/4 61,319 61,768 64,576 65,699 65,512 65,699 63,172 28,825 28,498
3 65,928 65,699 65,750 65,546 65,724 65,699 63,402 28,587 28,868
3-1/4 69,100 65,699 65,505 65,699 65,671 65,422 63,459
3-1/2 68,787 65,512 65,750 65,750 65,512 65,035 63,516
3-3/4 69,011 65,278 65,310 65,086 65,405 63,044 62,885
4 85,761 89,844 93,928 98,012 99,544 99,455 99,605
4-1/2 96,481 99,559 99,505 99,605 99,544 99,544 99,444
5 99,518 99,578 99,603 99,442 99,544 99,544 99,467
5-1/2 99,447 99,447 99,447 99,503 99,437 99,521 99,559
6 99,482 99,503 99,564 99,482 99,544 99,544 99,513
6-1/2 99,411 99,521 99,466 99,544 99,544 99,499 99,444
7 99,554 99,578 99,447 99,482 99,459 99,411 99,375
7-1/2 99,429 99,390 99,505 99,544 99,544 99,544 99,582
8 99,482 99,428 98,938 99,319 99,373 99,455 99,605
9 98,732 98,717 98,625 99,605 99,544 99,544 99,237
10 98,625 98,829 98,625 99,237 99,544 98,659 98,778
11 98,660 98,829 97,294 98,829 98,735 98,791 98,548
12
13
14
15

I S G Burns Harbor Plate Inc
Sheared Mill Maximum Dimensions
Table E (F1)Hot Roll-As Rolled
Structural Grades: ASTM A36 A283 A572 A573 A242 A588 A709 Gr36 Gr 50 & Gr 50W
PVQ Grades:(not Heat treated) ASTM A285 A299 A455 A516 A612 A662
Shipbuilding Grades: ABS, ASTM A131, MIL-S-22698, Gr A B D DS AH & DH
Chemistry Grades: Ordered to less than 0.39 Carbon
Width
Min
Thickness Lgth 40 42 45 48 51 54 57 60 63 66 69 72 75 78 81 84 87 90 93
0.1875 72 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
0.2500 72 675 750 855 960 975 1,000 1,000 1,000 1,000 1,020 1,020 1,020 1,020 1,020 1,020 1,020 1,020 1,020 1,020
0.3125 72 830 880 910 960 1,020 1,080 1,170 1,250 1,250 1,250 1,250 1,250 1,250 1,250 1,250 1,250 1,250 1,250 1,175
0.3750 72 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1,525 1,525 1,525 1,525 1,525 1,525 1,525 1,510
0.4375 72 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1,525 1,525 1,525 1,525 1,525 1,525 1,525 1,510
0.5000 72 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1,525 1,525 1,525 1,525 1,525 1,525 1,525 1,510
0.5625 72 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1,525 1,525 1,525 1,525 1,525 1,525 1,525 1,510
0.6250 72 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1,525 1,525 1,525 1,525 1,525 1,525 1,525 1,510
0.6875 72 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1,525 1,525 1,525 1,525 1,525 1,525 1,525 1,510
0.7500 72 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1,525 1,525 1,525 1,525 1,525 1,486 1,436 1,390
0.8125 72 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1,525 1,525 1,525 1,473 1,420 1,371 1,326 1,283
0.8750 72 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1,525 1,477 1,420 1,368 1,319 1,273 1,231 1,191
1.0000 72 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1,525 1,292 1,243 1,197 1,154 1,114 1,077 1,042
1.1250 72 890 1,000 1,225 1,440 1,440 1,440 1,440 1,440 1,440 1,440 1,440 1,437 1,149 1,105 1,064 1,026 990 957 926
1.2500 72 890 1,000 1,225 1,440 1,440 1,440 1,440 1,440 1,440 1,440 1,440 1,293 1,034 994 957 923 891 861 834
1.5000 72 890 1,000 1,225 1,440 1,440 1,440 1,440 1,440 1,440 1,440 1,440 1,077 861 828 798 769 743 718 695
1.7500 78 860 920 980 1,050 1,050 1,050 1,200 1,307 1,302 1,297 1,292 924 738 710 684 659 636 615 595
2.0000 78 840 900 960 1,000 1,000 1,000 1,149 1,144 1,139 1,134 1,130 808 646 621 598 577 557 538 521
2.2500 78 810 870 940 1,000 1,030 1,027 1,022 1,017 1,013 1,008 1,005 718 574 552 532 513 495 478 463
2.5000 78 800 850 910 936 930 925 920 915 911 908 904 646 517 497 478 461 445 430 417
2.7500 78 770 865 857 851 846 841 836 832 829 825 822 588 470 452 435 419 405 391 379
3.0000 78 750 793 786 780 775 771 766 763 760 756 754 539 430 414 399 384 371 359 347
3.2500 78 725 732 725 720 715 711 707 704 701 698 696 497 397 382 368 355 342 331 320
3.3333 78 700 713 707 702 698 693 690 686 684 681 678 485 387 372 359 346 334 323 312
3.5000 78 684 679 674 669 664 660 657 654 651 648 646 462 369 355 342 329 318 307 297
3.7500 78 625 634 629 624 620 616 613 610 608 605 603 431 344 331 319 307 297 287 278
4.0000 78 575 594 589 585 581 578 575 572 570 567 565 404 323 310 299 288 278 269 260
= Over 3.3333" Thick 2:1 reduction ratio only - NO PVQ
Items over 71” wide and over 27,500# single pc weight are subject to the availability of 12” thick slabs.
Plates though 1-1/2" thick are in minimum lengths of 72". Plates over 1-1/2" thick are in minimum lengths of 78".
For thicknesses and widths between the above values, use the shortest length bracketing your entry.
All the values shown may be modified under certain conditions, Inquire for more information.
SIZE CARDS BH - REVISED FOR HPS JUNE 2004 Table E (F1)Hot Roll-As Rolled 6/29/2004 9:52 AM
Table E (F1)Hot Roll-As Rolled
Structural Grades: ASTM A36 A283 a572 A573 A242 A588 A709 Gr36 Gr 50 & Gr 50W
PVQ Grades:(not Heat treated) ASTM A285 A299 A455 A516 A612 A662
Shipbuilding Grades: ABS, ASTM A131, MIL-S-22698, Gr A B D DS AH & DH
Chemistry Grades: Ordered to less than 0.39 Carbon
Width
Min
Thickness Lgth 96 99 102 105 108 111 114 117 120 123 126 129 132 135 138 141 144 147 150
0.1875 72 480 480 480 480 480 480 480 480 480 480 480 480 480
0.2500 72 1,020 1,020 1,020 960 900 840 780 750 740 740 720 720 720 720 720 630 550
0.3125 72 1,100 1,070 1,050 990 920 870 840 820 800 785 780 780 780 780 780 765 760 600 480
0.3750 72 1,500 1,470 1,450 1,390 1,350 1,320 1,300 1,270 1,250 1,250 1,250 1,160 1,050 900 780 770 760 600 480
0.4375 72 1,500 1,455 1,400 1,370 1,350 1,320 1,300 1,270 1,250 1,250 1,250 1,160 1,050 960 850 790 760 660 540
0.5000 72 1,500 1,455 1,400 1,370 1,350 1,320 1,300 1,270 1,250 1,220 1,200 1,140 1,100 1,010 900 870 850 790 750
0.5625 72 1,500 1,455 1,400 1,340 1,300 1,300 1,300 1,270 1,250 1,220 1,200 1,140 1,100 1,010 900 870 850 790 750
0.6250 72 1,500 1,455 1,400 1,340 1,300 1,300 1,300 1,270 1,250 1,220 1,200 1,140 1,100 1,070 1,050 975 900 825 750
0.6875 72 1,469 1,424 1,382 1,343 1,305 1,270 1,237 1,205 1,175 1,146 1,119 1,093 1,068 1,044 1,022 975 900 825 750
0.7500 72 1,346 1,305 1,267 1,231 1,197 1,164 1,134 1,105 1,077 1,051 1,026 1,002 979 957 936 916 897 825 750
0.8125 72 1,243 1,205 1,170 1,136 1,105 1,075 1,046 1,020 994 970 947 925 904 884 864 846 828 800 750
0.8750 72 1,154 1,119 1,086 1,055 1,026 998 972 947 923 900 879 859 839 820 803 785 769 753 738
1.0000 72 1,010 979 950 923 897 873 850 828 808 788 769 751 734 718 702 687 673 659 646
1.1250 72 897 870 845 820 798 776 756 736 718 700 684 668 652 638 624 611 598 586 574
1.2500 72 808 783 760 738 718 698 680 663 646 630 615 601 587 574 562 550 538 527 517
1.5000 72 673 652 633 615 598 582 567 552 538 525 513 501 489 478 468 458 448 439 430
1.7500 78 577 559 543 527 513 499 486 473 461 450 439 429 419 410 401 392 384 376 369
2.0000 78 505 489 475 461 448 436 425 414 404 394 384 375 367 359 351 343 336 329 323
2.2500 78 448 435 422 410 399 388 378 368 359 350 342 334 326 319 312 305 299 293 287
2.5000 78 404 391 380 369 359 349 340 331 323 315 307 300 293 287 281 275 269 263 258
2.7500 78 367 356 345 335 326 317 309 301 293 286 279 273 267 261 255 250 244 239 235
3.0000 78 336 326 316 307 299 291 283 276 269 262 256 250 244 239 234 229 224 219 215
3.2500 78 310 301 292 284 276 268 261 255 248 242 236 231 226 221 216 211 207 202 198
3.3333 78 303 293 285 277 269 262 255 248 242 236 230 225 220 215 210 206 202 197 193
3.5000 78 288 279 271 263 256 249 243 236 230 225 219 214 209 205 200 196 192 188 184
3.7500 78 269 261 253 246 239 232 226 221 215 210 205 200 195 191 187 183 179 175 172
4.0000 78 252 244 237 230 224 218 212 207 202 197 192 187 183 179 175 171 168 164 161
SIZE CARDS BH - REVISED FOR HPS JUNE 2004 Table E (F1)Hot Roll-As Rolled 6/29/2004 9:52 AM
Table F (F2)Control Finish Temp
Structural Grades: Any Grade rolled by this process to improve Impact Toughness properties, such as
ASTM A808.
Width
Min
Thickness Lgth 40 42 45 48 51 54 57 60 63 66 69 72 75 78 81 84 87 90 93
0.1875 72 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
0.2500 72 675 750 855 960 975 1,000 1,000 1,000 1,000 1,020 1,020 1020 1020 1020 1020 1020 1020 1020 1020
0.3125 72 830 880 910 960 1,020 1,080 1,170 1,250 1,250 1,250 1,250 1250 1250 1250 1250 1250 1250 1250 1175
0.3750 72 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1525 1525 1525 1525 1525 1525 1525 1510
0.4375 72 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1525 1525 1525 1525 1525 1525 1525 1510
0.5000 72 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1525 1525 1525 1525 1525 1525 1525 1510
0.5625 72 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1525 1525 1525 1525 1525 1525 1525 1510
0.6250 72 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1525 1525 1525 1525 1525 1525 1525 1510
0.6875 72 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1525 1525 1525 1525 1525 1525 1525 1510
0.7500 72 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1525 1525 1525 1525 1525 1486 1436 1390
0.8125 72 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1525 1525 1525 1473 1420 1371 1326 1283
0.8750 72 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1525 1477 1420 1368 1319 1273 1231 1191
1.0000 72 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1371 1292 1243 1197 1154 1114 1077 1042
1.1250 72 890 1,000 1,225 1,440 1,440 1,440 1,440 1,440 1,440 1,440 1,440 1219 1149 1105 1064 1026 990 957 926
1.2500 72 890 1,000 1,225 1,440 1,440 1,440 1,440 1,440 1,440 1,440 1,440 1097 1034 994 957 923 891 861 834
1.5000 72 890 1,000 1,225 1,440 1,440 1,440 1,440 1,440 1,440 1,440 1,440 914 861 828 798 769 743 718 695
1.7500 78 860 920 980 1,050 1,050 1,050 1,200 1,307 1,302 1,297 1,292 784 738 710 684 659 636 615 595
2.0000 78 840 900 960 1,000 1,000 1,000 1,149 1,144 1,139 1,134 1,130 686 646 621 598 577 557 538 521
2.2500 78 810 870 940 1,000 1,030 1,027 1,022 1,017 1,013 1,008 1,005 609 574 552 532 513 495 478 463
2.5000 78 800 850 910 936 930 925 920 915 911 908 904 549 517 497 478 461 445 430 417
2.7500 78 770 865 857 851 846 841 836 832 829 825 822 499 470 452 435 419 405 391 379
3.0000 78 750 793 786 780 775 771 766 763 760 756 754 457 430 414 399 384 371 359 347
3.2500
3.3333
3.5000
3.7500
4.0000
Min Item total Lgth 303 300 297 295 293 292 290 287 287 286 285 284 283 282 282 281 280 280 279
SIZE CARDS BH - REVISED FOR HPS JUNE 2004 Table F (F2)Control Finish Temp 6/29/2004 9:52 AM
Table F (F2)Control Finish Temp
Structural Grades: ASTM A808 and any Grade rolled by this process to improve Impact Toughness
properties
Width
Min
Thickness Lgth 96 99 102 105 108 111 114 117 120 123 126 129 132 135 138 141 144 147 150
0.1875 72 480 480 480 480 480 480 480 480 480
0.2500 72 1020 1020 1020 960 900 840 780 750 740 740 720 720 720
0.3125 72 1100 1070 1050 990 920 870 840 820 800 785 780 780 780 780 780 765 760
0.3750 72 1500 1470 1450 1390 1350 1320 1300 1270 1250 1250 1250 1160 1050 900 780 770 760 600 480
0.4375 72 1500 1455 1400 1370 1350 1320 1300 1270 1250 1250 1250 1160 1050 960 850 790 760 660 540
0.5000 72 1500 1455 1400 1370 1350 1320 1300 1270 1250 1220 1200 1140 1100 1010 900 870 850 790 750
0.5625 72 1500 1455 1400 1340 1300 1300 1300 1270 1250 1220 1200 1140 1100 1010 900 870 850 790 750
0.6250 72 1500 1455 1400 1340 1300 1300 1300 1270 1250 1220 1200 1140 1100 1070 1050 975 900 825 750
0.6875 72 1469 1424 1382 1343 1305 1270 1237 1205 1175 1146 1119 1093 1068 1044 1022 975 900 825 750
0.7500 72 1346 1305 1267 1231 1197 1164 1134 1105 1077 1051 1026 1002 979 957 936 916 897 825 750
0.8125 72 1243 1205 1170 1136 1105 1075 1046 1020 994 970 947 925 904 884 864 846 828 800 750
0.8750 72 1154 1119 1086 1055 1026 998 972 947 923 900 879 859 839 820 803 785 769 753 738
1.0000 72 1010 979 950 923 897 873 850 828 808 788 769 751 734 718 702 687 673 659 646
1.1250 72 897 870 845 820 798 776 756 736 718 700 684 668 652 638 624 611 598
1.2500 72 808 783 760 738 718 698 680 663 646 630 615 601 587 574 562 550 538
1.5000 72 673 652 633 615 598 582 567 552 538 525 513 501 489 478 468 458 448
1.7500 78 577 559 543 527 513 499 486 473 461 450 439 429 419 410 401 392 384
2.0000 78 505 489 475 461 448 436 425 414 404 394 384 375 367 359 351 343 336
2.2500 78 448 435 422 410 399 388 378 368 359 350 342 334 326 319 312 305 299
2.5000 78 404 391 380 369 359 349 340 331 323 315 307 300 293 287 281 275 269
2.7500 78 367 356 345 335 326 317 309 301 293 286 279 273 267 261 255 250 244
3.0000 78 336 326 316 307 299 291 283 276 269 262 256 250 244 239 234 229 224
3.2500
3.3333
3.5000
3.7500
4.0000
Min Item total Lgth 279 278 278 277 277 277 276 276 276 275 275 275 274 274 274 274 273
SIZE CARDS BH - REVISED FOR HPS JUNE 2004 Table F (F2)Control Finish Temp 6/29/2004 9:52 AM
Table G (F3)ContRoll <= 65ksi Y
Structural Grades: Any Grade rolled by this process to improve Impact Toughness properties through
65 KSI Yield Strength, such as ASTM A572 Gr 42, 50, ,55, 60 & 65, A656 Gr 50-60, BethStar 50-60.
Width
Min
Thickness Lgth 40 42 45 48 51 54 57 60 63 66 69 72 75 78 81 84 87 90 93
0.1875 78 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
0.2500 78 675 750 855 960 975 1,000 1,000 1,000 1,000 1,020 1,020 1020 1020 1020 1020 1020 1020 1020 1020
0.3125 78 830 880 910 960 1,020 1,080 1,170 1,250 1,250 1,250 1,250 1250 1250 1250 1250 1250 1250 1250 1175
0.3750 78 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1525 1525 1525 1525 1525 1525 1525 1510
0.4375 78 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1525 1525 1525 1525 1525 1525 1525 1510
0.5000 78 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1525 1525 1525 1525 1525 1525 1525 1510
0.5625 78 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1525 1525 1525 1525 1525 1525 1525 1510
0.6250 78 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1525 1525 1525 1525 1525 1525 1525 1510
0.6875 78 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1525 1525 1525 1525 1525 1525 1525 1510
0.7500 78 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1525 1525 1525 1525 1525 1486 1436 1390
0.8125 78 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1525 1525 1525 1473 1420 1371 1326 1283
0.8750 78 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1525 1477 1420 1368 1319 1273 1231 1191
1.0000 78 890 1,000 1,225 1,440 1,470 1,480 1,490 1,500 1,500 1,500 1,515 1371 1292 1243 1197 1154 1114 1077 1042
1.1250 78 890 1,000 1,225 1,440 1,440 1,440 1,440 1,440 1,440 1,440 1,440 1219 1149 1105 1064 1026 990 957 926
1.2500 78 890 1,000 1,225 1,440 1,440 1,440 1,440 1,440 1,440 1,440 1,440 1097 1034 994 957 923 891 861 834
1.5000 78 890 1,000 1,225 1,440 1,440 1,440 1,440 1,440 1,440 1,440 1,440 914 861 828 798 769 743 718 695
1.7500 78 860 920 980 1,050 1,050 1,050 1,200 1,307 1,302 1,297 1,292 784 738 710 684 659 636 615 595
2.0000 78 840 900 960 1,000 1,000 1,000 1,149 1,144 1,139 1,134 1,130 686 646 621 598 577 557 538 521
2.2500
2.5000
2.7500
3.0000
3.2500
3.3333
3.5000
3.7500
4.0000
SIZE CARDS BH - REVISED FOR HPS JUNE 2004 Table G (F3)ContRoll <= 65ksi Y 6/29/2004 9:53 AM
Table G (F3)ContRoll <= 65ksi Y
Structural Grades: Any Grade rolled by this process to improve Impact Toughness properties through
65 KSI Yield Strength, such as ASTM A572 Gr 42, 50, & 60, A656 Gr 50-60, BethStar 50-60.
Width
Min
Thickness Lgth 96 99 102 105 108 111 114 117 120 123 126 129 132 135 138 141 144 147 150
0.1875 78 480 480 480 480 480 480 480 480 480
0.2500 78 1020 1020 1020 960 900 840 780 750 740 740 720 720 720
0.3125 78 1100 1070 1050 990 920 870 840 820 800 785 780 780 780 780 780 765 760
0.3750 78 1500 1470 1450 1390 1350 1320 1300 1270 1250 1250 1250 1160 1050 900 780 770 760 600 480
0.4375 78 1500 1455 1400 1370 1350 1320 1300 1270 1250 1250 1250 1160 1050 960 850 790 760 660 540
0.5000 78 1500 1455 1400 1370 1350 1320 1300 1270 1250 1220 1200 1140 1100 1010 900 870 850 790 750
0.5625 78 1500 1455 1400 1340 1300 1300 1300 1270 1250 1220 1200 1140 1100 1010 900 870 850 790 750
0.6250 78 1500 1455 1400 1340 1300 1300 1300 1270 1250 1220 1200 1140 1100 1070 1050 975 900 825 750
0.6875 78 1469 1424 1382 1343 1305 1270 1237 1205 1175 1146 1119 1093 1068 1044 1022 975 900 825 750
0.7500 78 1346 1305 1267 1231 1197 1164 1134 1105 1077 1051 1026 1002 979 957 936 916 897 825 750
0.8125 78 1243 1205 1170 1136 1105 1075 1046 1020 994 970 947 925 904 884 864 846 828 800 750
0.8750 78 1154 1119 1086 1055 1026 998 972 947 923 900 879 859 839 820 803 785 769 753 738
1.0000 78 1010 979 950 923 897 873 850 828 808 788 769 751 734 718 702 687 673 659 646
1.1250 78 897 870 845 820 798 776 756 736 718 700 684 668 652 638 624 611 598
1.2500 78 808 783 760 738 718 698 680 663 646 630 615 601 587 574 562 550 538
1.5000 78 673 652 633 615 598 582 567 552 538 525 513 501 489 478 468 458 448
1.7500 78 577 559 543 527 513 499 486 473 461 450 439 429 419 410 401 392 384
2.0000 78 505 489 475 461 448 436 425 414 404 394 384 375 367 359 351 343 336
2.2500
2.5000
2.7500
3.0000
3.2500
3.3333
3.5000
3.7500
4.0000
SIZE CARDS BH - REVISED FOR HPS JUNE 2004 Table G (F3)ContRoll <= 65ksi Y 6/29/2004 9:53 AM
Table H1 (F4)ContRoll > 65ksi Y
Structural Grades: Any Grade rolled by this process over 65 to < 80 KSI Yield Strength, such as A656
Gr 70, BethStar 70
Width
Min
Thickness Lgth 40 42 45 48 51 54 57 60 63 66 69 72 75 78 81 84 87 90 93 96
0.1875 78 x x x 480 480 480 480 480 480 480 480 480 x x x x x x x x
0.2500 78 675 750 855 960 975 1,000 1,000 1,000 1,000 1,020 1,020 1,020 1,020 1,020 1,020 1,020 1,020 1,020 1,020 x
0.3125 78 830 880 910 960 1,020 1,080 1,170 1,250 1,250 1,250 1,250 1,250 1,250 1,250 1,250 1,250 1,250 1,250 1,175 960
0.3750 78 890 1,000 1,225 1,440 1,470 1,480 1,490 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,510 960
0.4375 78 890 1,000 1,225 1,440 1,470 1,480 1,490 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,510 960
0.5000 78 890 1,000 1,225 1,440 1,470 1,480 1,490 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,510 960
0.5625 78 890 1,000 1,225 1,440 1,470 1,480 1,490 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,510 960
0.6250 78 890 1,000 1,225 1,440 1,470 1,480 1,490 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,510 960
0.6875 78 890 1,000 1,225 1,440 1,470 1,480 1,490 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,510 960
0.7500 78 890 1,000 1,225 1,440 1,470 1,480 1,490 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,390 960
0.8125 78 890 1,000 1,225 1,440 1,470 1,480 1,490 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,283 960
0.8750 78 890 1,000 1,225 1,440 1,470 1,480 1,490 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,248 1,231 1,191 960
1.0000 78 890 1,000 1,225 1,440 1,470 1,480 1,490 1,248 1,248 1,248 1,248 1,248 1,248 1,243 1,197 1,154 1,114 1,077 1,042 960
1.1250
1.2500
1.5000
1.7500
2.0000
2.2500
2.5000
2.7500
3.0000
3.2500
3.3333
3.5000
3.7500
4.0000
SIZE CARDS BH - REVISED FOR HPS JUNE 2004 Table H1 (F4)ContRoll > 65ksi Y 6/29/2004 9:53 AM
Table H2 (F4A)ContRoll 80ksi
Structural Grades: Any Grade rolled by this process with 80 KSI Min Yield Strength, such as ASTM
A656 Type 7 Gr 80, BethStar 80.
Width
Min
Thickness Lgth 40 42 45 48 51 54 57 60 63 66 69 72 75 78 81 84 87 90 93 96
0.1875 78 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
0.2500 78 780 780 780 780 780 780 780 780 780 780 780 780 780 480 480 480 480
0.3125 78 780 780 780 780 780 780 780 780 780 780 780 780 780 780 780 780 780
0.3750 78 780 780 780 780 780 780 780 780 780 780 780 780 780 780 780 780 780
0.4375 78 780 780 780 780 780 780 780 780 780 780 780 780 780 780 780 780 780
0.5000 78 780 780 780 780 780 780 780 780 780 780 780 780 780 780 780 780 780
0.5625 78 780 780 780 780 780 780 780 780 780 780 780 780 780 780 780 780 780
0.6250 78 780 780 780 780 780 780 780 780 780 780 780 780 780 780 780 780 780
0.6875 78 780 780 780 780 780 780 780 780 780 780 780 780 780 780 780 780 780
0.7500 78 780 780 780 780 780 780 780 780 780 780 780 780 780 780 780 780 780
0.8125
0.8750
1.0000
1.1250
1.2500
1.5000
1.7500
2.0000
2.2500
2.5000
2.7500
3.0000
3.2500
3.3333
3.5000
3.7500
4.0000
SIZE CARDS BH - REVISED FOR HPS JUNE 2004 Table H2 (F4A)ContRoll 80ksi 6/29/2004 9:53 AM
Table I (F5) Normalized
All Grades which require Normalizing.
Also Grades requiring Annealing or Stress Relieving subject to inquiry only.
Width
Min
Thickness Lgth 40 42 45 48 51 54 57 60 63 66 69 72 75 78 81 84 87 90 93
0.1875 72 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
0.2500 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.3125 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.3750 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.4375 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.5000 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.5625 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.6250 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.6875 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.7500 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.8125 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.8750 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
1.0000 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
1.1250 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
1.2500 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
1.5000 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
1.7500 78 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 636 615 595
2.0000 78 650 650 650 650 650 650 650 650 650 650 650 650 646 621 598 577 557 538 521
2.2500 78 650 650 650 650 650 650 650 650 650 650 650 650 574 552 532 513 495 478 463
2.5000 78 650 650 650 650 650 650 650 650 650 650 650 646 517 497 478 461 445 430 417
2.7500 78 650 650 650 650 650 650 650 650 650 650 650 588 470 452 435 419 405 391 379
3.0000 78 650 650 650 650 650 650 650 650 650 650 650 539 430 414 399 384 371 359 347
3.2500 78 650 650 650 650 650 650 650 650 650 650 650 497 397 382 368 355 342 331 320
3.3333 78 650 650 650 650 650 650 650 650 650 650 650 485 387 372 359 346 334 323 312
3.5000 78 650 650 650 650 650 650 650 650 650 648 646 462 369 355 342 329 318 307 297
3.7500 78 625 634 629 624 620 616 613 610 608 605 603 431 344 331 319 307 297 287 278
4.0000 78 575 594 589 585 581 578 575 572 570 567 565 404 323 310 299 288 278 269 260

SIZE CARDS BH - REVISED FOR HPS JUNE 2004 Table I (F5) Normalized 6/29/2004 9:53 AM
Table I (F5) Normalized
All Grades which require Normalizing.
Also Grades requiring Annealing or Stress Relieving subject to inquiry only.
Width
Min
Thickness Lgth 96 99 102 105 108 111 114 117 120 123 126 129 132 135 138 141 144 147 150
0.1875 72 480 480 480 480 480 480 480 480 480 480 480 480 480
0.2500 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 630 550
0.3125 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 600 480
0.3750 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 600 480
0.4375 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 540
0.5000 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.5625 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.6250 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.6875 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.7500 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.8125 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.8750 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
1.0000 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 646
1.1250 72 650 650 650 650 650 650 650 650 650 650 650 650 650 638 624 611 598 586 574
1.2500 72 650 650 650 650 650 650 650 650 646 630 615 601 587 574 562 550 538 527 517
1.5000 72 650 650 633 615 598 582 567 552 538 525 513 501 489 478 468 458 448 439 430
1.7500 78 577 559 543 527 513 499 486 473 461 450 439 429 419 410 401 392 384 376 369
2.0000 78 505 489 475 461 448 436 425 414 404 394 384 375 367 359 351 343 336 329 323
2.2500 78 448 435 422 410 399 388 378 368 359 350 342 334 326 319 312 305 299 293 287
2.5000 78 404 391 380 369 359 349 340 331 323 315 307 300 293 287 281 275 269 263 258
2.7500 78 367 356 345 335 326 317 309 301 293 286 279 273 267 261 255 250 244 239 235
3.0000 78 336 326 316 307 299 291 283 276 269 262 256 250 244 239 234 229 224 219 215
3.2500 78 310 301 292 284 276 268 261 255 248 242 236 231 226 221 216 211 207 202 198
3.3333 78 303 293 285 277 269 262 255 248 242 236 230 225 220 215 210 206 202 197 193
3.5000 78 288 279 271 263 256 249 243 236 230 225 219 214 209 205 200 196 192 188 184
3.7500 78 269 261 253 246 239 232 226 221 215 210 205 200 195 191 187 183 179 175 172
4.0000 78 252 244 237 230 224 218 212 207 202 197 192 187 183 179 175 171 168 164 161

SIZE CARDS BH - REVISED FOR HPS JUNE 2004 Table I (F5) Normalized 6/29/2004 9:53 AM
Table J (F6) Q & T
Structural Grades: ASTM A678 RQC60 80 90 100 A709 Gr 100 & 100T A514 Gr B & H
PVQ Grades:ASTM A517 Gr B & H A537 Class 2, A709 Gr. HPS 70W
Width
Min
Thickness Lgth 40 42 45 48 51 54 57 60 63 66 69 72 75 78 81 84 87 90 93
0.1875 72 480 480 480 480 480 480 480 480 480 480 480 480 480
0.2500 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.3125 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.3750 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.4375 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.5000 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.5625 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.6250 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.6875 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.7500 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.8125 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.8750 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
1.0000 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
1.1250 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
1.2500 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
1.5000 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
1.7500 78 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 636 615 595
2.0000 78 650 650 650 650 650 650 650 650 650 650 650 650 646 621 598 577 557 538 521
2.2500 78 650 650 650 650 650 650 650 650 650 650 650 650 574 552 532 513 495 478 463
2.5000 78 650 650 650 650 650 650 650 650 650 650 650 646 517 497 478 461 445 430 417
2.7500 78 650 650 650 650 650 650 650 650 650 650 650 588 470 452 435 419 405 391 379
3.0000 78 650 650 650 650 650 650 650 650 650 650 650 539 430 414 399 384 371 359 347
3.2500 78 650 650 650 650 650 650 650 650 650 650 650 497 397 382 368 355 342 331 320
3.3333 78 650 650 650 650 650 650 650 650 650 650 650 485 387 372 359 346 334 323 312
3.5000 78 650 650 650 650 650 650 650 650 650 648 646 462 369 355 342 329 318 307 297
3.7500 78 625 634 629 624 620 616 613 610 608 605 603 431 344 331 319 307 297 287 278
4.0000 78 575 594 589 585 581 578 575 572 570 567 565 404 323 310 299 288 278 269 260

SIZE CARDS BH - REVISED FOR HPS JUNE 2004 Table J (F6) Q & T 6/29/2004 9:53 AM
Table J (F6) Q & T
Structural Grades: ASTM A678 RQC60 80 90 100 A709 Gr 100 & 100T A514 Gr B & H
PVQ Grades:ASTM A517 Gr B & H A537 Class 2, A709 Gr. HPS 70W
Width
Min
Thickness Lgth 96 99 102 105 108 111 114 117 120 123 126 129 132 135 138 141 144 147 150
0.1875 72
0.2500 72 650 650 650 650 650 650 650 650 650
0.3125 72 650 650 650 650 650 650 650 650 650
0.3750 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.4375 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 540
0.5000 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.5625 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.6250 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.6875 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.7500 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.8125 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
0.8750 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650
1.0000 72 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650 646
1.1250 72 650 650 650 650 650 650 650 650 650 650 650 650 650 638 624 611 598 586 574
1.2500 72 650 650 650 650 650 650 650 650 646 630 615 601 587 574 562 550 538 527 517
1.5000 72 650 650 633 615 598 582 567 552 538 525 513 501 489 478 468 458 448 439 430
1.7500 78 577 559 543 527 513 499 486 473 461 450 439 429 419 410 401 392 384 376 369
2.0000 78 505 489 475 461 448 436 425 414 404 394 384 375 367 359 351 343 336 329 323
2.2500 78 448 435 422 410 399 388 378 368 359 350 342 334 326 319 312 305 299 293 287
2.5000 78 404 391 380 369 359 349 340 331 323 315 307 300 293 287 281 275 269 263 258
2.7500 78 367 356 345 335 326 317 309 301 293 286 279 273 267 261 255 250 244 239 235
3.0000 78 336 326 316 307 299 291 283 276 269 262 256 250 244 239 234 229 224 219 215
3.2500 78 310 301 292 284 276 268 261 255 248 242 236 231 226 221 216 211 207 202 198
3.3333 78 303 293 285 277 269 262 255 248 242 236 230 225 220 215 210 206 202 197 193
3.5000 78 288 279 271 263 256 249 243 236 230 225 219 214 209 205 200 196 192 188 184
3.7500 78 269 261 253 246 239 232 226 221 215 210 205 200 195 191 187 183 179 175 172
4.0000 78 252 244 237 230 224 218 212 207 202 197 192 187 183 179 175 171 168 164 161

SIZE CARDS BH - REVISED FOR HPS JUNE 2004 Table J (F6) Q & T 6/29/2004 9:53 AM
Table C1045 SpPt slabs
1045
Width
Min
Thickness Lgth 40 42 45 48 51 54 57 60 63 66 69 72 75 78 81 84 87 90 93
0.1875 72 360 360 360 360 360 480 480 480 480 480 480 480 480 480 480 480
0.2500 72 300 300 390 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
0.3125 72 300 300 390 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
0.3750 72 300 300 450 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600
0.4375 72 300 300 450 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600
0.5000 72 300 300 450 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600
0.5625 72 300 300 450 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600
0.6250 72 300 300 450 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600
0.6875 72 300 300 450 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600
0.7500 72 300 300 450 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600
0.8125 72 300 300 450 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600
0.8750 72 300 300 450 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600
1.0000 72 300 300 450 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600
1.1250 72 350 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600
1.2500 72 400 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600
1.5000 72 450 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600
1.7500 78 500 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 584
2.0000 78 550 600 600 600 600 600 600 600 600 600 600 600 600 600 587 566 547 528 511
2.2500 78 575 600 600 600 600 600 600 600 600 600 600 587 564 542 522 503 486 470 454
2.5000 78 590 590 600 600 600 600 600 600 600 577 551 528 507 488 470 453 437 423 409
2.7500 78 534 534 600 600 600 600 600 576 549 524 501 480 461 443 427 412 397 384 372
3.0000 78 490 490 600 600 530 585 556 528 503 480 459 440 423 406 391 377 364 352 341
3.2500 78 470 470 559 574 530 540 513 488 464 443 424 406 390 375 361 348 336 325 314
3.3333 78 450 450 517 547 510 510 501 476 453 432 413 396 380 366 352 340 328 317 307
3.5000 78 430 430 475 520 500 480 477 453 431 412 394 377 362 348 335 323 312 302 292
3.7500 78 400 400 435 470 460 450 445 423 402 384 367 352 338 325 313 302 291 282 272
4.0000 78 370 370 395 420 420 420 417 396 377 360 344 330 317 305 293 283 273 264 254
SIZE CARDS BH - REVISED FOR HPS JUNE 2004 Table C1045 SpPt slabs 6/29/2004 9:53 AM
Table C1045 SpPt slabs
1045
Width
Min
Thickness Lgth 96 99 102 105 108 111 114 117 120 123 126 129 132 135 138 141 144 147 150
0.1875 72 480
0.2500 72 480 480 480 480 480 480 480
0.3125 72 480 480 480 480 480 480 480 480 480
0.3750 72 600 600 600 600 600 600 600 600 600 600 600
0.4375 72 600 600 600 600 600 600 600 600 600 600 600 600 600
0.5000 72 600 600 600 600 600 600 600 600 600 600 600 600 600
0.5625 72 600 600 600 600 600 600 600 600 600 600 600 600 600
0.6250 72 600 600 600 600 600 600 600 600 600 600 600 600 600
0.6875 72 600 600 600 600 600 600 600 600 600 600 600 600 600
0.7500 72 600 600 600 600 600 600 600 600 600 600 600 600 600
0.8125 72 600 600 600 600 600 600 600 600 600 600 600 600 600
0.8750 72 600 600 600 600 600 600 600 600 600 600 600 600 600
1.0000 72 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600
1.1250 72 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600
1.2500 72 600 600 600 600 600 600 600 600 600 600 600 590 577 564 551 540 528
1.5000 72 600 600 600 600 587 571 556 542 528 516 503 492 480 470 459 450 440
1.7500 78 566 549 533 518 503 490 477 464 453 442 431 421 412 402 394 385 377
2.0000 78 495 480 466 453 440 428 417 406 396 387 377 369 360 352 344 337 330
2.2500 78 440 427 414 402 391 381 371 361 352 344 335 328 320 313 306 300 293
2.5000 78 396 384 373 362 352 343 334 325 317 309 302 295 288 282 275 270 264
2.7500 78 360 349 339 329 320 311 303 295 288 281 274 268 262 256 250 245 240
3.0000 78 330 320 311 302 293 285 278 271 264 258 251 246 240 235 229 225 220
3.2500 78 305 295 287 278 271 263 256 250 244 238 232 227 221 216 212 207 203
3.3333 78 297 288 280 272 264 257 250 244 238 232 226 221 216 211 206 202 198
3.5000 78 283 274 266 259 251 245 238 232 226 221 215 210 206 201 197 192 188
3.7500 78 264 256 248 241 235 228 222 216 211 206 201 196 192 188 183 180 176
4.0000 78 247 240 233 226 220 214 208 203 198 193 188 184 180 176 172 168 165
SIZE CARDS BH - REVISED FOR HPS JUNE 2004 Table C1045 SpPt slabs 6/29/2004 9:53 AM
Table for HPS 70W
AASHTO M270 Gr HPS 70W - ASTM A709 Gr HPS 70W - ASTM A709M Gr HPS 485W
Produced: TMCP (Control Fininshed, Control Rolled, or Accelerated Cooling)
Width
Min
Thickness Lgth 40 42 45 48 51 54 57 60 63 66 69 72 75 78 81 84 87 90 93 96
0.1875 X
0.2500 X
0.3125 X
0.3750 X
0.4375 X
0.5000 600 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500
0.5625 600 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500
0.6250 600 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,460 1,410
0.6875 600 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,475 1,450 1,425 1,400 1,375 1,335 1,280
0.7500 600 Note: Actual 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,450 1,400 1,520 1,486 1,436 1,390 1,346
0.8125 600 sizes accepted 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,420 1,395 1,345 1,310 1,420 1,371 1,326 1,283 1,243
0.8750 600 for TMCP 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,340 1,477 1,420 1,368 1,319 1,273 1,231 1,191 1,154
1.0000 600 production are 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,360 1,292 1,243 1,197 1,154 1,114 1,077 1,042 1,010
1.1250 600 subject to 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,225 1,149 1,105 1,064 1,026 990 957 926 897
1.2500 600 inquiry 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,290 1,034 994 957 923 891 861 834 808
1.3750 600 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,180 940 904 870 839 810 783 758 734
1.5000 600 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,270 861 828 798 769 743 718 695 673
1.6285 600 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,170 793 763 735 708 684 661 640 620
1.7500 600 1,400 1,400 1,400 1,400 1,400 1,400 1,400 1,400 1,090 738 710 684 659 636 615
1.8750 600 1,290 1,290 1,290 1,290 1,290 1,290 1,290 1,290 1,020 689 663 638 615
2.0000 600 1,240 1,240 1,240 1,240 1,240 1,240 1,240 1,240 950 646 621
2.2500 X
2.5000 X
2.7500 X
3.0000 X
3.2500 X
3.3333 X
3.5000 X
3.7500 X
4.0000 X
Plates produced Control Rolled minumum lengths of 400". Plates produced T.M.C.P. in minimum lengths of 600".
SIZE CARDS BH - REVISED FOR HPS JUNE 2004 High Performance Steel 6/29/2004 9:53 AM
Table for HPS 70W
AASHTO M270 Gr HPS 70W - ASTM A709 Gr HPS 70W - ASTM A709M Gr HPS 485W
Produced: TMCP (Control Fininshed, Control Rolled, or Accelerated Cooling)
Width
Min
Thickness Lgth 99 102 105 108 111 114 117 120 123 126 129 132 135 138 141 144 147 150
0.1875 X
0.2500 X
0.3125 X
0.3750 X
0.4375 X
0.5000 600 1,500 1,500 1,500 1,500 1,500 1,490 1,450 1,410
0.5625 600 1,500 1,480 1,440 1,400 1,360 1,320 1,290 1,260
0.6250 600 1,370 1,330 1,300 1,260 1,220 1,190 1,160 1,130
0.6875 600 1,240 1,205 1,175 1,140 1,105 1,075 1,045 1,015
0.7500 600 1,300 1,267 1,230 1,197 1,164 1,134 1,100 1,070
0.8125 600 1,205 1,170 1,136 1,105 1,075 1,046 1,020 994
0.8750 600 1,119 1,086 1,055 1,026 998 972 947 923
1.0000 600 979 950 923 897 873 850 828 808
1.1250 600 870 845 820 798 776 756 736 718
1.2500 600 783 760 738 718 698 680 663 646
1.3750 600 712 691 671 652 635 618 602
1.5000 600 652 633 615
1.6285 600 601
1.7500 600
1.8750 600
2.0000 600 x x
2.2500 X
2.5000 X
2.7500 X
3.0000 X
3.2500 X
3.3333 X
3.5000 X
3.7500 X
4.0000 X
Plates produced Control Rolled minumum lengths of 400". Plates produced T.M.C.P. in minimum lengths of 600".
SIZE CARDS BH - REVISED FOR HPS JUNE 2004 High Performance Steel 6/29/2004 9:53 AM
PHYSICAL PROPERTIES OF STEEL
ITEM ENGLISH UNITS METRIC UNITS

Specific Gravity 7.9 7.9
Density 490 lb/ft 3
7850 kg/m3
Melting Point 2370°F–2640°F 1300°C–1450°C
Btu (Cal)
Specific Heat 0.12 0.12
(lb) (°F) (gr) (°C)
Linear Coefficient of 1 1
6.5 x 10 -6 (11.7) x 10 -6
Thermal Expansion F C
Volumetric Coefficient 1 1
19.5 x 10 - 6 (35.1) x 10 -6
of Thermal Expansion F C
Thermal Conductivity 34 (Btu)
58.9W/(m)(K)
at 60°F (hr) (ft) (°F)
Electrical Resistivity
17 x 10 -8 (ohm-meters)
at 60°F
Speed of Sound
18,000 ft/sec 5490 m/sec
through Steel
Young’s Modulus
29,000,000 lb/(in)2 207,000 MPa
of Elasticity
Poisson’s Ratio, 0.3 in the elastic range and 0.5 in the plastic range
Bulk Modulus 23,000,000 lb/(in)2 159,000 MPa
Shear Modulus 12,000,000 lb/(in) 2
83,000 MPa
.07 @ 100°F .07 @ 38°C
Emissivity of Polished
.10 @ 500°F .10 @ 260°C
Metal Surface
.14 @ 1000°F .14 @ 540°C
Emissivity of Oxidized
0.80 0.80
Steel Plate at 60°F
The properties listed above vary with the chemistry of the steel plate.
The values shown are typical for non-alloy plate grades.
If more accuracy is required, refer to a physics handbook.
For more information about ISG Plate and continuous updates, visit our web site at: www.intlsteel.com
The following product brochures are available at www.intlsteel.com in the Plate Products Literature section:
Carbon Plate Steels
API Steels for Offshore Structures
BethStar® Control-Rolled Steels
HP Magnet Plate Steel
T-Star® Improved Weldability Steels
Alloy Plate Steels
9% Nickel Steel
Alloy 33VT – High Strength Steels for High Temperature Pressure Vessels
Duracorr® Stainless Steels
• Welding Guidelines for Duracorr®
• Fabrication Guidelines for Bridge Applications – Duracorr®
• Duracorr® 300 Abrasion Resistant Steel
• Duracorr® for Exhaust Flanges
Hardwear® 400F, 450F and 500F Abrasion Resistant Steels
• Summary of Available Abrasion Resistant Steels
High Strength Q&T, Structural Steels
• A514 and T-1®
• Lukens® 130
• Lukens® 690Z, Thick Plate for Jack-Up Rigs
• Spartan™, Improved Weldability Steels
Military Alloy Steels
MTD® and Tool Steels
Both Carbon and Alloy Plate Steels
A516 and A387 Pressure Vessel Steels
• Effect of PWHT on ASTM A516 Steel
Fineline® Low Sulfur, Clean Steels
Flame Cut Products
Free-Machining Steels Clean-Cut® and C1119™/C1144™ Steels
HPS 70W High Performance Steels for Bridges
• HPS 50W
• HPS 100W
• HPS Update
LASEReady™ Steels
Mill Edge Plate
Physical properties of Steel
Roll-bonded Clad Steels
SMART® Steckel Rolled Steels
Sure-Foot® Safety Plate
Weathering Steels
The information contained herein has been obtained from current proprietary and published specifications and is accurate to the best of our
knowledge. However, the characteristics described or implied here may not apply in all situations. Where specific plate properties are desired,
please communicate with ISG Plate.
The specifier should recognize further that all mechanical and chemical tests, relating to a particular specification, will be in accordance with
policy and test locations. Unless otherwise specified, test locations will be in accordance with those defined in the latest “Plates and Rolled
Floor Plates: Carbon, High Strength Low Alloy and Alloy” (Steel Products Manual)* and ISG Plate can certify the values stated in this bulletin
for only the locations in which the material is tested.
Since the specifications and codes change frequently, this information should be checked against the latest standards to insure accuracy.
* Published by the Iron and Steel Society, 186 Thorn Hill Road, Warrendale, PA 15086-7528 (724) 776-1535
International Steel Group, Inc.
Form No. 001 3/04 Printed in U.S.A. Phone: 800-966-5352 Email: plate.professionals@intlsteel.com Web: www.intlsteel.com
■ ■

Plate Steel Catalogue

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Plate Steel Catalogue

Uploaded by

Copyright:

Available Formats

2004-2005

International Steel Group, Inc.

Coatesville, PA SPECIAL PLATE AND FLAMECUT TOLERANCES

The Plate Professionals

ISG PLATE CARBON AND ALLOY PLATE STEELS

PLATE DIMENSIONS AVAILABLE FROM ISG PLATE*

ABBREVIATIONS USED IN THIS GUIDE

SPECIFICATION A36 A36 A36 A36 A36 A131*

A202 A202 A203 A203 A203 A203

Nickel ■ ■ 2.10/2.50 2.10/2.50 3.25/3.75 3.25/3.75

Other Elements - - F/G/P F/G/P F/G/P F/G/P

A203 A204 A204 A204 A225† A225†

Nickel 3.25/3.75 ■ ■ ■ .40/.70 .40/.70

Other Elements F/G/P - - - .13/.18V .10/.18V

A242†▲ A283 A283 A283 A283

* Coatesville produces to .04 Max. Phosphorus.

A285 A285 A285 A299 A299 A302 A302

Molybdenum ■ ■ ■ ■ ■ .45/.60 .45/.60

A387*** A387 A387 A387 A387

Molybdenum .45/.60 .45/.60 ■ .45/.65 .45/.60 .90/1.10 .90/1.10 .90/1.10

Other Elements F/G/P F/G/P Mandatory - - - - -

A387** A387 A387 A387 A387 A387 A387 A387

Molybdenum .90/1.10 .45/.65 .90/1.10 .45/.65 .45/.60 .90/1.10 .90/1.10 .45/.65

A514† A514* A515 A515 A515 A516

Nickel 1.20/1.50 1.20/1.50 ■ ■ ■ ■

Molybdenum .45/.60 .40/.60 ■ ■ ■ ■

Other Elements .001/.005 B .03/.08 V C/G/P C/G/P C/G/P F/G/P

A516 A516 A516 A517† A517* A517† A517*

Nickel .30/.70 1.20/1.50 1.20/1.50 - - ■ .40/.70

A533 A533 A533 A533 A533 A533 A533

Nickel .70/1.00 .20/.40 - .40/.70 .70/1.00 .20/.40 -

Other Elements F/G/P F/G/P F/G/P F/G/P F/G/P F/G/P F/G/P

A533 A533 A533 A542*

■ Restricted to ASTM A20 limits for unspecified elements.

A542 A542 A542 A542 A542 A542 A542

A542 A542 A542 A542 A542 A542 A542

A543 A543 A543 A543 A543 A543

Nickel 2.25/4.00 2.00/3.50 2.25/4.00 2.00/3.50 2.25/4.00 2.00/3.50 8.50/9.50

Other Elements .03 V .03 V .03 V .03 V .03 V .03 V ■

A572† A572†▲ A572†▲ A572† A572†

A573 A573 A588†* A588†▲▲* A633†

A656† A656†▲ A656†▲ A656†▲

A709 A709† A709†† A710††

Nickel .25 .25 .25 .70/1.00 ■ ■

Molybdenum .08 .08 .08 .15/.25 ■ ■

Copper .35 .35 .35 1.00/1.30 ■ ■

Other Elements .08 V .08 V .08 V .02 Min. Cb .05 Cb .04/.11 V

A829 A841† A841† A841†

Yield Strength (Min. ksi) 45 60 50 to - 50 to 50 to 60 to

A841† A871† A871†

Alloy 4130 Alloy 4130 Mod. Alloy 4140 Alloy 4340

ABS† ABS† ABS† ABS† ABS†

Manganese 21/2 x C .60 min. .60 min. .70 min. .90/1.60

ABS† ABS† ABS† ABS† ABS†

API-2W†▲ API-2W†▲ API-2W†▲ API-2W†▲

API Steels Brochure

The designation number of a chemistry-only steel indicates the chemical composition of

10XX — carbon steels

A830 A830 A829 A829 A829 A829

ISG PLATE FREE MACHINING STEELS

BethStar® BethStar® BethStar® BethStar® V-Star® V-Star® T-Star®* T-Star®*

* Also available as A572 Type 5.

▲▲ ISG Plate declared chemistries

Chromium .60/.90 .45/.75 1.00/1.80 1.00/1.80 - 1.20/1.60 .40/.70