Take-off and landing

performance
Contents
PIC responsibilities................................. 5 Determining performance...................... 20

How to comply............................................... 5 Group rating system...................................... 20

P-charts...................................................... 22
Performance factors............................... 6
Aircraft Flight Manual..................................... 30
Weight......................................................... 6
Air transport operations................................. 32
Air density..................................................... 6
Know your aircraft........................................ 33
Wind.......................................................... 10
Slope......................................................... 12 Conclusion......................................... 34

Surface....................................................... 12 Performance questions .................................. 35

Obstacle clearance........................................ 13
Flap setting................................................. 14
Ground effect............................................... 14
Wing surface................................................ 16
Tyre pressure............................................... 16

Other considerations............................ 17
Runway distance.......................................... 17
Pilot technique............................................. 17
Speed control.............................................. 18
Decision points............................................ 18
Contingencies.............................................. 19

See the CAA website for Civil Aviation Rules, advisory circulars, airworthiness directives, forms,
and more safety publications. Visit aviation.govt.nz.
Every effort is made to ensure the information in this booklet is accurate and up-to-date at the
time of publishing. But numerous changes can occur with time, especially in regard to airspace
and legislation. Readers are reminded to get appropriate up-to-date information.
 Take-off and landing performance 3

A significant number of accidents and incidents occur

during take-off and landing. Ensuring that your take-off
and landing can be conducted within the confines of the
runway will significantly contribute to the safety of these
critical phases of flight.
4
 Take-off and landing performance 5

PIC responsibilities
Civil Aviation Rules clearly indicate that it is the
responsibility of the pilot in command to ensure that
they operate their aircraft in a safe manner with respect
to take-off and landing performance. In particular, rule
91.201(2) states that “A pilot-in-command of an aircraft
must… during the flight, ensure the safe operation of
the aircraft and the safety of its occupants…”.

How to comply If you are operating under Part 135,

there will be specific performance
If you are operating under Part 91,
requirements you will need to meet –
Advisory Circular 91-3 Aeroplane
these are briefly discussed later in
Performance Under Part 91 provides
this booklet.
guidance on how best to comply with
rule 91.201(2). Essentially, AC91-3 says Note that the group rating system,
that you can determine the take-off and for instance, is quite conservative and
landing performance of your aircraft sometimes shows that an aircraft will
by one of the following three methods: not fit on to a particular runway when
in fact P-chart calculations (which are
• Group Rating system;
more precise) show otherwise. It is
• P-charts; or quite acceptable to select the method
that shows that the operation can
• Approved Aircraft Flight
be performed within the aircraft’s
Manual data.
performance limits.
AC 91-3 also provides performance
All of these three methods are
correction tables for surface type, slope,
discussed, with worked examples,
and contaminated runway surfaces,
later in this booklet.
since this information is often omitted
from many light aircraft Flight Manuals.
6

Performance factors
Many different factors affect aircraft performance.

Weight Air density

The gross weight of the aircraft directly affects As air density decreases, both engine and
stall speed, a 10 percent increase in weight aerodynamic performance decrease.
increasing the stall speed by 5 percent.
Effect of pressure on density
Take-off
Atmospheric pressure decreases with altitude,
Liftoff speed is generally about 15 percent because the air near the earth’s surface is
above the stalling speed, so an increase in compressed by the air above it. As altitude
weight will mean a higher liftoff speed. increases, air is free to expand and therefore
becomes less dense.
In addition to the higher speed required,
acceleration of the heavier aeroplane is
Effect of temperature on density
slower. Hence, a longer take-off distance
will be required. As a general rule of thumb, Temperature generally also decreases with
a 10 percent increase in take-off weight altitude. This causes the air to contract and
has the effect of increasing the take-off run become denser. However, the drop in pressure
by about 20 percent. as altitude is increased has the dominating
effect on density when compared with the
Landing effect of temperature.

Heavier landing weights require higher

Effect of humidity on density
approach speeds, which means the aircraft
will have greater momentum and require Water vapour is lighter than air; consequently
more runway in which to land and stop. moist air is lighter than dry air. It is lightest
(or least dense) when, in a given set of
A 10 percent increase in landing weight has
conditions, it contains the maximum amount
the effect of increasing the landing distance
of water vapour.
by about 10 percent.
 Take-off and landing performance 7

International standard atmosphere Height above Temp Pressure Relative

sea level (°C) (hPa) density
A standard atmosphere has been established (thousands
of feet)
to enable comparison of aircraft
performances, calibration of altimeters 40 -56 188 0.247
and other practical uses.
Cirrus clouds
In the International Standard Atmosphere
a particular pressure and temperature 35 -54 239 0.311
distribution with height is assumed.

At sea level the pressure is taken to be 1013.2

hPa and the temperature 15˚C. 30 -44 301 0.375
In this ‘average’ atmosphere, any pressure level
Mt Everest
has a standard corresponding altitude called
the pressure altitude (based on a lapse rate of
25 -34 377 0.449
approximately one hPa per 30 feet at lower
levels) and a corresponding temperature called
the ISA temperature. Pressure altitude is the
height that will register on a sensitive altimeter
20 -25 466 0.533
whenever its sub-scale is set to 1013.2 hPa.

In the standard atmosphere, temperature falls High cumulus clouds

off with height at a rate of 1.98˚C per 1000 feet
up to 36,090 feet, above which it is assumed to
15 -15 572 0.629
be constant (see Figure 1).
Mt Cook
Warm air is less dense than cold air.
10 -5 697 0.739
Thus, when the temperature at any altitude
in the atmosphere is higher than the
temperature would be in the standard
atmosphere at the same altitude, then the 5 +5 843 0.862
air at that altitude will be less dense than
in the standard atmosphere. Stratus and nimbus clouds
ISA also assumes dry air. In normal conditions,
0 +15 1013 1.000
the amount of water vapour in the air does
not make a significant difference to its density. Sea level
However, as warm air can contain much
more water vapour than cold air, at high Figure 1: The international standard atmosphere
temperatures and high humidity, the reduction
in density may become significant and degrade
aircraft take-off performance accordingly.
8

Density altitude Density altitude can be calculated by taking

pressure altitude and adding (or subtracting)
Density altitude represents the combined
120 feet for each 1˚C above (or below) ISA.
effect of pressure altitude and temperature.
It is defined as the height in the standard When an aircraft is taking off at a density
atmosphere, which has a density altitude above ISA sea level, it will still get
corresponding to the density at the particular airborne at the same indicated airspeed as at
location (on the ground or in the air) at which sea level, but because of the lower density the
the density altitude is being measured. true airspeed (TAS) will be greater. To achieve
this higher speed with the same engine power,
Aircraft performance depends on air density,
a longer take-off run will be needed.
which directly affects lift and drag, engine
power, and propeller efficiency. As air density The effect of a high density altitude on the
decreases, aircraft performance decreases. power developed from the unsupercharged
Density altitude, therefore, provides a basis engine is adverse, and less power will be
for relating air density to ISA, so that aircraft available for take-off. (When taking off from
performance can be readily determined. a high density altitude aerodrome, the engine
will not even develop the power it is capable
of unless the mixture is correctly leaned.)
 Take-off and landing performance 9

An increase in density altitude, therefore, High density altitudes are found most
has a twofold effect on the take-off: commonly at high-elevation aerodromes
when the temperature is high.
• An increased take-off speed (TAS)
is required. Low atmospheric pressures will accentuate
the effect. Taking off with a heavy aeroplane
• Engine power and propeller efficiency
in these conditions is fraught with danger.
are reduced.
Your take-off performance sums have got to
The approximate effect of these two be right.
components on take-off and landing
performance are:

• The take-off distance is increased by

one percent for every 100 feet of
aerodrome pressure altitude above
sea level, and the landing distance by
one percent for every 400 feet.

• The take-off distance is increased by one

percent for every 1˚C above the standard
temperature for the aerodrome elevation.

• Rate-of-climb and angle-of-climb are

noticeably reduced, as is obstacle
clearance after take-off.

Glentanner aerodrome has an elevation of 1824 feet.

10

Wind Gusting winds

Headwind A gusting wind situation will require that you

keep the aeroplane on the ground for a slightly
Taking off into wind results in the shortest longer period of time to provide a better
take-off run and the lowest groundspeed on margin above the stall, thereby increasing
liftoff. If it becomes necessary to abandon your overall take-off roll.
the take-off, not only will the lower
groundspeed make it easier to stop, but Gusty conditions also necessitate a higher
also the shorter take-off run means more approach speed, which results in a longer
runway available to do so. Climbing into landing roll.
wind gives a lower groundspeed and Turbulence and windshear
therefore a steeper angle of climb after
take-off; this is good for obstacle clearance. The possibility of turbulence and windshear
should be considered when working out
Landing into wind results in a lower
take-off or landing distances. Windshear
groundspeed and shorter landing run.
is a change in wind velocity (speed and/or
Take-off and landing distances are reduced direction) over a very short distance.
by about 1.50 percent for each knot of
The presence of windshear can cause sudden
headwind up to 20 knots.
fluctuations in airspeed after take-off or during
an approach.
Tailwind
Hangars, buildings and areas of trees all
Taking off downwind results in a much longer
influence the flow of the wind near them.
distance to get airborne and a decreased angle
The mechanical turbulence resulting from
of climb, which is bad for obstacle clearance.
this disturbed airflow may become very
For a 5-knot tailwind component, the take-off marked in the lee of the obstruction.
distance should be multiplied by 1.25, and
In winds below 15 knots, turbulence occurs
for 10 knots, by 1.55.
in the lee of the obstruction and may extend
Landing distances are similarly increased. vertically to about one third higher again than
the obstruction.
Tailwind take-offs and landings should be
avoided unless it can be established with In winds above 20 knots, eddies can occur on
absolute certainty that there is sufficient the leeward side to a distance of about 10 to 15
distance available to do so. times the obstruction height and up to twice
the obstruction height above the ground.
Crosswind
A crosswind situation will affect take-off
and landing performance, mainly because
of the reduced headwind component.

If the wind is 30 degrees off the runway

heading, the headwind is effectively reduced
by 15 percent. If the wind is 45 degrees off,
the headwind is reduced by 30 percent.
Take-off and landing performance 11
12

Slope Surface
An uphill slope increases the take-off ground Take-off
run, and a downhill slope increases the
Grass, soft ground or snow increase the
landing ground run. For example, an upslope
rolling resistance and therefore the take-off
of 2 percent increases take-off distance by
ground run will be longer than on a sealed
about 15 percent and a 2 percent downslope
or paved runway.
decreases it by about 10 percent.
Dry grass can increase take-off distance by
Slopes can be calculated from known or
up to 15 percent. Long wet grass can further
estimated information. Divide the difference
increase this distance depending on the length
in height between the two strip ends by
and wetness of the grass and the weight and
the strip length (working in the same
wheel size of the aircraft. Aircraft type is a big
units of measurement). For example,
factor here – attempting to take off on such
15 metres (50 feet) height difference on
a surface in a Piper Cub is an entirely different
a 750-metre strip gives an answer of 0.02,
proposition to a Cessna 172 for example.
or a 2 percent slope.
 Take-off and landing performance 13

It is often inadvisable to take off in long wet Obstacle clearance

grass, and it can be impossible.
Plan to clear obstacles on the climbout path
Puddles of water on the runway can also by at least 50 feet.
significantly retard acceleration.
Consider what your aircraft’s climb gradient
Landing is likely to be as part of your take-off
performance calculations – especially if terrain,
On landing, grass or snow cause an
wires, and the possibility of downdraughts
increased ground roll, despite increased
are factors in the climbout path. Calculating
rolling resistance, because the brakes are
the gain-of-height per mile is straightforward.
less effective.
Simply divide the aircraft’s known rate-of-climb
Long wet grass can mean a very large increase performance by the number of nautical miles
in the landing run due to this effect. covered per minute eg, 500 fpm/1.1 NM per
min = 454 feet per NM of climb performance
(this assumes a groundspeed of 66 knots).

This will then give you a good indication of

whether you will be able to maintain safe
terrain and obstacle clearance.
 14

Flap setting Ground effect

Flap reduces the stalling speed and enables When flying close to the ground, the wing
you to lift off at a lower indicated airspeed. generates less induced drag than a wing out
This can mean a shorter ground run, but of ground effect. Thus the wing is more
it may not give any reduction in take-off efficient while in ground effect.
distance to 50 feet because flap usually
While this can be useful on occasions, it can
causes a reduction in the rate of climb.
also trap the unwary into expecting greater
The recommended flap setting should climb performance than the aeroplane is
always be used. capable of sustaining.

On landing, ground effect may produce

‘floating’ and result in a go-around (or an
overrun, if the danger signs are ignored)
particularly at very fast approach speeds.
Photo courtesy of Kaye Nairn.
 Take-off and landing performance 15

Low-wing aeroplanes are more sensitive in ground effect to let it accelerate to best
to ground effect than high-wing ones. angle-of-climb speed before climbing out.
This is especially important when departing
Ground effect makes it possible to lift off at
from a short soft field with obstacles.
too high a pitch angle, or too soon with a heavy
load. Taking off too steeply (or too soon) will If you inadvertently leave ground effect
cause the angle of attack to be at or near that too soon, and the aeroplane is not able to
of a stall, with drag and thrust nearly equal, accelerate to its proper climb speed, the only
and thus no chance of accelerating. way to retrieve the situation is to lower the
nose, allow the aircraft to accelerate, and then
Don’t force your aircraft to become airborne
climb. The problem is, that you may not be
too soon.
able to achieve satisfactory obstacle clearance
Let it lift off when it’s ready to fly. Utilise as result, which is all the more reason for
ground effect by briefly holding the aircraft making sure that you get it right first time.

Consider what your aircraft’s climb gradient

is likely to be as part of your take-off
performance calculations – especially if terrain,
wires, and the possibility of downdraughts are
factors in the climbout path.
16

Wing surface Tyre pressure

Deposits on the wing surface, such as Low tyre pressure (perhaps hidden by grass
raindrops or insects, can have a significant or spats) will increase the take-off run.
effect on laminar flow aerofoils such as used
This is something that should always be
on some self-launching motor gliders and
checked during the pre-flight walk around.
high-performance home-built aeroplanes.
Stall speeds are increased and greater
distances are required.

The presence of surface frost, ice or snow

affects any aerofoil, including the
propeller. Minor hangar rash or dents on
the lifting surfaces or propeller will also
degrade performance. Keep all lifting
surfaces damage-free and clean to ensure
maximum performance.
 Take-off and landing performance 17

Other considerations
It is good airmanship to think about what technique, speed,
and decision point, you will use for every take-off and landing.

Runway distance Pilot technique

Information on available runway distances is Ensure that recommended short-field take-off
published in the AIP New Zealand AD section. and landing techniques are always used when
operating out of airstrips where the distance
At non-published airstrips, distances should be
available is a factor. Consult the Flight Manual,
paced out. Pace length should be established
or an instructor, if you are unsure as to what
accurately – or deliberately underestimated.
technique should be used for a particular
If you expect to use a strip frequently, you aircraft. Consider undertaking some dual
should ensure that the length is measured short-field take-off and landing revision.
accurately (for example, by using a rope of
known length).
 18

Speed control Decision points

The speed at which you lift off is very important You should always nominate a decision
with regard to achieving the best take-off point where you will abandon the take-off
performance from the aircraft – particularly or discontinue the approach if things are not
when runway length is a significant factor. going as expected.
Likewise, letting the aircraft accelerate in
For take-off, this is the point at which there
ground effect to best angle-of-climb speed
is sufficient distance available to safely
is also critical.
stop the aircraft should it accelerate slower
For landing, correct speeds for the prevailing than expected or suffer a power loss.
conditions are obviously important. This is particularly important for multi-
engine aircraft.
Arrive too fast and you will use up more
runway, too slow on approach and you may
stall and not arrive on the runway at all.
Photo courtesy of Kaye Nairn.
 Take-off and landing performance 19

For landing, the decision point should be Contingencies

a height where there is sufficient room to
effect a safe go-around if you are not happy Even after having worked out your aircraft’s
with the approach. An important factor here, take-off or landing performance, it is prudent
and one that is often overlooked by pilots, to add a contingency to allow for other factors
is the assessment of groundspeed while that you may have overlooked.
on approach. A check of the windsock and For instance, the engine may not be
an estimate of whether your ground-speed performing as well as it used to, the brakes
is about what you would expect for your may be dragging slightly, the propeller may
airspeed when on short final is good practice. be less efficient than it used to be, you might
Any tailwind component very significantly encounter a lull or shift in the wind, etc.
increases the landing distance, so a go-
around is usually the best course of action Where take-off and landing distances are
should this be the case. looking marginal, we suggest that you always
factor a contingency of at least 10 percent
into your calculations.
20

Determining performance
The following section gives three ways of ensuring adequate
take-off and landing performance for private operations.

Group rating system into wind using recommended short-field

techniques. The system can’t take into account
What is it? specific conditions on the day, so the aircraft
Every light aircraft in New Zealand has been Group Rating number allocated is conservative
(and still is) assigned a group rating number for private operations. However, if ambient
from 1 to 8 – based on its take-off and landing conditions differ significantly from ISA in a way
performance at maximum weight (1 = excellent that will reduce performance, and the airstrip
performance and 8 = poor performance). is sloping, it would be wise to use a P-chart
Runways that are published in the AIP or the Flight Manual to determine take-off and
New Zealand AD section are also assigned landing distances.
a group rating number based on their The group number of your aircraft can be
characteristics (1 = short distance available found in the front of its Flight Manual.
and 8 = long distance available). The runway group rating number can be found
The Group Rating system allows for runway in the table at the top of each aerodrome
length, slope and surface, with a generous operational data page in the AIP New Zealand
allowance for ambient conditions, and it AD section.
assumes that the operation is conducted
 Take-off and landing performance 21

How does it work? AIP New Zealand NZGS AD 2 - 52.1

Certificated Aerodrome 1NM W of Gisborne
GISBORNE
Using the group rating NZGS Not for operational use OPERATIONAL DATA (1)
system is very simple. For RWY
example, if your aircraft has Take-off distance LDG
RWY SFC Strength Gp Slope ASDA
a group rating of 6, it is safe 1:20 1:25 1:30 1:40 1:50 1:62.5 DIST
14 PCN 20 0.07U 1371
to operate from runways 32
B
F/B/Y/T
8
0.07D
1310 1371
1270
1310

with a group rating of 6 or 14

14
B
PCN 20
F/B/Y/T
7
6
0.07U
777
EXTENSION CLOSED
868

greater. If the runway group 32

B
PCN 20 6
0.07D EXTENSION CLOSED
777
32 F/B/Y/T 7 868
rating is less than 6 it may 14 ESWL 4 551
Gr 0.08U
14 1600 6 750
still be safe to operate under 32 ESWL 6 750
Gr 0.08D
favourable conditions, but 32 1600 4 551
03 ESWL 0.05U 1042 1170
you would need to work out 21
Gr
5700
8
0.05D 1170 1042
09 ESWL 0.1U 1039 1173
the distances required for 27
Gr
9080
8
0.1D 1173 1039

the prevailing conditions

MINIMA
Figure 2
using one of the other
two methods. IFR Take-off
RWY Day Night
14/32 300–1500 300–1500
Note that some runways may
03/21
in fact have more than one 09/27
600–1500
600 1500 NA

group number assigned to

(continued)
them because of differences
in the available take-off and
landing distance, for example
Gisborne (see Figure 2).
 22

P-charts wind to readily determine take-off and landing

distances for a particular set of conditions.
Use of a Performance chart (P-chart) is another
acceptable method (which is more precise The CAA no longer (as of 1 April 1997) includes
than the group rating system) for determining a P-chart when it issues a Flight Manual for an
take-off and landing performance. aircraft. But for the majority of light aircraft
in New Zealand the P-chart remains a very
What are they? practical method of determining take-off and
landing performance and can be completed
P-charts are graphs developed from
with ease. If your aircraft Flight Manual has a
manufacturers’ test data. They apply various
P-chart, it is important to know how to use it
factors, including density altitude, type of
and to understand what is being allowed for.
operation, runway surface, runway slope and
Photo courtesy of Jack Stanton.
 Take-off and landing performance 23

If your aircraft Flight Manual has

a P-chart, it is important to know
how to use it and to understand
what is being allowed for.
24

Examples
The following example gives guidance on how to best use a P-chart. (Note that at the bottom
of the P-chart there is a tracking depiction on how to work from box to box.)

Take-off distance example Determining density altitude

The red line in Figure 3 relates to the data The first thing we need to do is to calculate
supplied below and the blue line provides the airstrip’s density altitude.
a comparison for ‘standard’ conditions. To do this we must determine the pressure
Note that all take-off distances are to a height altitude of the airstrip and then correct
of 50 feet, at which point a speed of 1.2 Vs it for temperature by using the ambient
(where Vs is the stall speed for the chosen temperature of the day (26˚C in this case).
configuration) is assumed to have been This is an area that many pilots seem to
achieved. Landing distances are also all from have difficulty with.
a height of 50 feet with a speed of 1.3 Vs when The easiest way to determine pressure
passing through that height. The distances altitude, if we are sitting in our aircraft,
given for private operations represent the is to set the sub-scale on the altimeter to
minimum distance acceptable, and pilots 1013.2 hPa. The altimeter will then read
should carefully review all factors (and other the pressure altitude of the aerodrome.
options) before landing at or taking off from
an aerodrome with only the bare minimum Alternatively, knowing that 1013.2 hPa is
distance available. ISA pressure at sea level, we calculate the
difference from today’s QNH (sea level
Type of Operation – Private pressure), which is 997 hPa. This is 16 hPa
Aircraft – Cessna 172P below 1013.2 hPa, and as each hectopascal
equals approximately 30 feet, this equates
Max all up weight – 1089 kg to 480 feet. We must now apply this
QNH – 997 hPa correcting figure to our aerodrome elevation
of 1320 feet. Do we add it or subtract it?
Temperature – 26˚C
Because the pressure today is lower than
Wind – 050˚M/15 knots standard (pressure decreases with altitude,
Aerodrome elevation – 1320 feet amsl 997 hPa being found at 480 feet amsl on
a standard day) we add the figure to
Runway – 020˚M aerodrome elevation, arriving at a pressure
Surface – grass altitude of 1800 feet.

Length – 730 metres

Slope – 1% up
 A – All operations – Grass – Night A B C 1300

Figure 3
TAKE-OFF B – All operations – Paved – Night
C – Air Transport – Grass – Day D
D – Air Transport – Paved – Day
This graph incorporates CASO 4 factors E – Private – Grass – Day 1200
and corrections and gives the take-off F – Private – Paved – Day E
distance to a height of 50 feet.
1100
CESSNA 172P
F
ENGINE: Avco Lycoming 0-320-D2J 1000
PROPELLER: McCauley 1C160 DTM7557
FLAPS 10˚
900
Full throttle prior to brake release
Takeoff speed over 50 ft:
800
1089 kg (2400 lb) 56 KIAS
998 kg (2200 lb) 54 KIAS
907 kg (2000 lb) 51 KIAS
700

600
DISTANCE REQUIRED (METRES)

500

START HERE
DENSITY 400
ALTITUDE
AMBIENT TEMPERATURE (˚C) 300
0 10 20 30 40 3 2 1 0 1 2 3 5 0 10 20
UP DOWN TAIL HEAD
4000 SLOPE (%) REPORTED WIND
(KNOTS)

)
4000’ 3000 )

lb)

00 lb
0 lb
ISA+20
3000’ 2000 200
240

g (20
g (2
k
kg (

ISA+10 1000
9

2000’
998
907 k
108
Take-off and landing performance

0 AC1

PRESSURE ALTITUDE (FEET)

1000’ ISA Issue 7
25
26

Density altitude graph Surface

Now we start at the box for determining From this point we track vertically up
density altitude which can be found at the into the next box, until we meet the line
bottom left of the chart. We enter the graph at “Private – Grass – Day”.
the top with the ambient temperature of 26˚C,
and track vertically down that line until we Slope
meet the imaginary angled pressure altitude
We then move horizontally to the next
line for 1800 feet (ie, a point just under the
box going through to the zero line. (This is
angled 2000-foot line).
most important – always go to the zero
(For our exercise, we don’t need to worry line in the last two boxes.) We then track
about the angled temperature lines marked parallel to the curved lines until we reach
“ISA+10” etc, which depict the ISA drop-off in the 1 percent up line.
temperature with altitude.)
Wind
From that point we exit the box horizontally
to the right. A scale is not usually marked on The headwind component must now be
the right-hand side of the box, but we have determined because the wind is not straight
shown the density altitude figures in colour on down the runway. The crosswind component
our example to give you a better appreciation graph in the Flight Manual can be used to
of what you are working out. (You will note calculate this (see figure 4). The headwind
that, although the aerodrome elevation in our component in this case is 13 knots.
example is only 1320 feet, the density altitude Now we move horizontally to the zero line of
under the prevailing conditions is 3500 feet – the wind box. Using the headwind component
quite a significant difference.) of 13 knots track parallel to the curved line
until we reach the 13-knot headwind line.
Weight From this point, we exit horizontally to the
Continue horizontally into the next box until right of the box, where we can read off the
we meet the weight line of 1089 kilograms distance required for take-off.
(ie, the maximum). You will notice that the
In this example nearly 700 metres is required
only variable on the chart that the pilot has
to reach a height of 50 feet. As the runway in
any control over is the weight of the aircraft.
this example is 730 metres long, we should be
Bearing this in mind, the graphs can be
able to take off safely (but remember this is
used to work out a safe operating weight
for short dry grass).
on marginal runways.
 Take-off and landing performance 27

EXAMPLE:
Wind speed 10 knots
FLIGHT Angle between wind
PATH direction and flight path 20˚
60
Headwind component 9.5 knots
0˚
10˚ Crosswind component 3.5 knots
20˚

50 30˚

W
IN
D
SP
EE
40˚

D
60

–
KN
40

O
H

TS
T
PA 50˚
T
50
H
IG
FL
HEADWIND COMPONENT – KNOTS

D
AN

30
60˚
N

40
IO
CT
RE
DI
D
IN

30
20
W

70˚
N
EE
TW
BE

20
E
GL
AN

10 80˚
10

0 90˚

-10 100˚

180˚170˚160˚ 150˚ 140˚ 130˚ 120˚ 110˚

-20
0 10 20 30 40 50 60
CROSSWIND COMPONENT – KNOTS

Figure 4: Wind components

28

Landing distance example At very high density altitudes, however, the

resulting higher true airspeed (TAS) should
Now work through the landing example
be borne in mind in relation to the approach
provided (see Figure 5) using the same aircraft,
and landing, as should the reduced power
aerodrome and weather conditions as above
available for a go-around.
by following the red line.
You will also note that the slope corrections are
Note that aerodrome elevation is used rather
reversed from the take-off situation; an uphill
than density altitude in this calculation,
slope on landing will decrease the landing
as engine performance is not a critical factor
distance and vice versa.
(unless a go-around becomes necessary).
 A B C D 1200

Figure 5
A – All operations – Grass – Night
LANDING B – Air transport – Grass – Day
E
C – All operations – Paved – Night
(TRICYCLE LANDING GEAR) D – Private – Grass – Day 1100
E – Air transport – Paved – Day
F – Private – Paved – Day F

This graph incorporates CASO 4 factors 1000

and corrections and gives the landing
distance from a height of 50 feet.
900
CESSNA 172P
FLAPS 30˚ 800
Power off
Maximum braking
700
Approach speed over 50 ft:
1089 kg (2400 lb) 61 KIAS
600

500
DISTANCE REQUIRED (METRES)

400

300

200
3 2 1 0 1 2 3 5 0 10 20
4000’ DOWN UP TAIL HEAD
SLOPE (%) REPORTED WIND
(KNOTS)

lb)
START AERODROME
HERE ELEVATION 2000’
(FEET)
1089 kg (2400
Take-off and landing performance

AC2
Sea level Issue 7
29
30

Aircraft Flight Manual AC91-3 suggests that take-off and landing

distances derived from the aircraft flight
Take-off and landing performance graphs/ manual should be corrected for variation in
tables in aircraft Flight Manuals vary from runway surface and slope by applying the
manufacturer to manufacturer. factors in Figures 6 and 7.
Usually they do not allow for as many If your aircraft Flight Manual has a P-chart,
variables as P-charts. we suggest that, in most cases, it is
Each graph or table will normally be preferable that you use it over other Flight
formulated for standard conditions (ie a level, Manual data – particularly if it is an old
dry, paved surface in nil wind with the aircraft Flight Manual, some of which tend to be
configured for a short-field take-off or landing) less comprehensive than their modern
and allows for variations in weight, pressure counterparts. Some manufacturers’ Flight
altitude, and temperature only. For tables, Manual data can also, at times, tend to be
these variables are usually given over rather optimistic rather than conservative about
a broad range, eg temperature in bands of their aircraft’s performance.
10˚C and pressure altitude in bands of 1000
feet. Other variables, such as wind and type
of surface, have to be allowed for manually
and added to the basic take-off or landing
distance as a percentage value.
 Take-off and landing performance 31

Figure 6:
Surface type Take-off distance factor Landing distance factor
Runway surface factors
Paved x 1.00 x 1.00

Coral x 1.00 x 1.05

Metal x 1.05 x 1.08

Rolled earth x 1.08 x 1.16

Grass x 1.14 x 1.18

Figure 7:
Take-off distance Landing distance
Runway slope factors Direction of slope % of slope
correction correction

1 +5% -5%

Uphill 2 +10% -10%

3 +15% -15%

1 -5% +5%

Downhill 2 -10% +10%

3 -15% +15%
32

Air transport operations than 50 percent of the reported headwind

(or not less than 150 percent of the reported
If you are operating a light aircraft on Air tailwind, as the case may be). There are also
Transport or Commercial Transport specific runway surface and slope correction
operations, there are specific performance factors to apply.
requirements that must be met in CAR
Part 135 Air Operations – Helicopters and Part 135 requires you to use Flight Manual
Small Aeroplanes, Subpart D. data to determine take-off and landing
performance. This may include the use of
For example, the take-off distance required P-charts but the group rating system is not
must not exceed 85 percent of the take-off run acceptable for air transport operations.
available. You must take account of not more
 Take-off and landing performance 33

See Advisory Circular 119-3 Air Operator This can serve as a basis for determining
Certification – Part 135 Operations for details whether it is necessary to carry out
on how to compile a P-chart and apply the performance calculations in any given
applicable Air Transport factors to your situation. Always err on the side of caution
aircraft Flight Manual performance data. when it comes to deciding whether such
calculations are necessary – it is better to
Know your aircraft be safe than sorry.

It is useful to work out, and remember, the If you own your own aircraft, you might like
take-off and landing distances required for to consider actually confirming what distance
your aircraft in ISA conditions at sea level, with it will take off and land in under these
nil slope, and nil wind on a sealed runway. conditions – get to know your own aircraft.
34

Conclusion
Take-off and landing are both high-risk phases of flight. The
more that we can do as pilots to minimise these risks, especially
when operating out of a short airstrip in an underpowered
aircraft, the safer we will be.

If take-off or landing performance is ever doubtful, then taking

the time to apply basic performance calculations is a prudent
thing to do and takes the ‘she’ll be right’ out of the situation.

Make performance calculations part of your pre-flight planning

if you suspect things might be tight.
 Take-off and landing performance 35

Performance questions
Now that you have seen how to use a P-chart, try these problems by using the chart provided
in the original example above (answers below).

1. A private flight, C172P, aircraft weight 4. A private flight, C172P, aircraft weight
1089 kg, QNH 1020 hPa, temperature 20˚C, 2400 lbs, QNH 1013 hPa, temperature
aerodrome elevation 400 feet, slope nil, 25˚C, aerodrome elevation 1000 feet,
grass/day, wind 250˚M at 5 knots, nil slope, grass/day, wind 220˚M at
runway 22. 10 knots, runway 22.
What take-off and landing distances Use the Flight Manual data provided below,
are required? and any other corrective factors required,
to calculate the take-off distance to 50 feet
2. An air transport flight, C172P, aircraft
under these conditions.
weight 1089 kg, QNH 997 hPa, temperature
26˚C, aerodrome elevation 1700 feet, slope
1 percent down, paved/day, wind 150˚M
at 10 knots, runway 18 (520 metres).
Can I safely land on runway 18 in
these conditions?
4. 1973 feet is required.
3. I would like to fly into Kaikoura (elevation
19 feet), which has a Group 4 grass runway,
Yes, I could land there at this weight.

in my private Group 6 Cessna 172P. Assume

3. Maximum weight would be 1045 kg.

standard pressure, a temperature of 25˚C, 2. Yes – 460 metres would be required.

and nil wind. The runway is 575 metres Landing – 460 metres.
long with no slope. 1. Take-off – 570 metres.
What would be the maximum allowable
weight for a safe take-off under these
problems:

conditions? Could I land there at

Answers to aircraft performance

this weight?

Take-off speed KIAS 0˚c 10˚c 20˚c 30˚c

Weight Press
LBs alt ft Total ft Total ft Total ft Total ft
Ground Ground Ground Ground
Lift off At 50 ft to clear to clear to clear to clear
roll ft roll ft roll ft roll ft
50 ft OBS 50 ft OBS 50 ft OBS 50 ft OBS

2400 51 56 S.L. 795 1460 860 1570 925 1685 995 1810
1000 875 1605 940 1725 1015 1860 1090 2000
2000 960 1770 1035 1910 1115 2060 1200 2220
3000 1055 1960 1140 2120 1230 2295 1325 2480
4000 1165 2185 1260 2365 1355 2570 1465 2790
5000 1285 2445 1390 2660 1500 2895 1620 3160
6000 1425 2755 1540 3015 1665 3300 1800 3620
7000 1580 3140 1710 3450 1850 3805 2000 4220
8000 1755 3615 1905 4015 2060 4480 –––– ––––

Notes: 1. Decrease distances 10 percent for each 9 knots of headwind.

2. For operation on a dry, grass runway, increase distances by 15 percent.
 See the CAA website for Civil Aviation Rules,
advisory circulars, airworthiness directives,
PO Box 3555 forms, and more safety publications.
Wellington 6140
To request publications such as GAPs and
Tel: +64 4 560 9400 posters email: publications@caa.govt.nz.
Fax: +64 4 569 2024
aviation.govt.nz
Email: info@caa.govt.nz
Take-off and landing performance
was revised in February 2020.