FX5U - Hardware Manual

Truy cập website https://plcmitsubishi.
com để có thêm nhiều tài liệu và bài viết hướng dẫn kỹ thuật hay
MELSEC iQ-F
FX5U User's Manual (Hardware)
Truy cập website https://plcmitsubishi.com để có thêm nhiều tài liệu và bài viết hướng dẫn kỹ thuật hay
SAFETY PRECAUTIONS
(Read these precautions before use.)
Before using this product, please read this manual and the relevant manuals introduced in this manual carefully and pay full
attention to safety in order to handle the product correctly.
This manual classifies the safety precautions into two categories: [ WARNING] and [ CAUTION].
Indicates that incorrect handling may cause hazardous conditions, resulting in

WARNING death or severe injury.
Indicates that incorrect handling may cause hazardous conditions, resulting in

CAUTION minor or moderate injury or property damage.
Depending on the circumstances, procedures indicated by [ CAUTION] may also cause severe injury.
It is important to follow all precautions for personal safety.
Store this manual in a safe place so that it can be read whenever necessary. Always forward it to the end user.
[DESIGN PRECAUTIONS]
WARNING
● Make sure to set up the following safety circuits outside the PLC to ensure safe system operation
even during external power supply problems or PLC failure. Otherwise, malfunctions may cause
serious accidents.
- Most importantly, set up the following: an emergency stop circuit, a protection circuit, an interlock
circuit for opposite movements (such as forward vs. reverse rotation), and an interlock circuit to
prevent damage to the equipment at the upper and lower positioning limits.
- Note that when the CPU module detects an error, such as a watchdog timer error, during self-
diagnosis, all outputs are turned off. Also, when an error that cannot be detected by the CPU
module occurs in an input/output control block, output control may be disabled. External circuits
and mechanisms should be designed to ensure safe machine operation in such a case.
- Note that the output current of the 24 V DC service power supply varies depending on the model
and the absence/presence of extension modules. If an overload occurs, the voltage automatically
drops, inputs in the PLC are disabled, and all outputs are turned off. External circuits and
mechanisms should be designed to ensure safe machine operation in such a case.
- Note that when an error occurs in a relay or transistor of an output circuit, the output might stay on
or off. For output signals that may lead to serious accidents, external circuits and mechanisms
should be designed to ensure safe machine operation.
● Construct an interlock circuit in the program so that the whole system always operates on the safe
side before executing the control (for data change) of the PLC in operation.
Read the manual thoroughly and ensure complete safety before executing other controls (for program
change, parameter change, forced output and operation status change) of the PLC in operation.
Otherwise, the machine may be damaged and accidents may occur due to erroneous operations.
● In an output circuit, when a load current exceeding the current rating or an overcurrent caused by a
load short-circuit flows for a long time, it may cause smoke and fire. To prevent this, configure an
external safety circuit, such as a fuse.
● For the operating status of each station after a communication failure of the network, refer to relevant
manuals for the network. Incorrect output or malfunction may result in an accident.
1
[DESIGN PRECAUTIONS]
CAUTION
● When an inductive load such as a lamp, heater, or solenoid valve is controlled, a large current
(approximately ten times greater than normal) may flow when the output is turned from off to on. Take
proper measures so that the flowing current does not exceed the value corresponding to the
maximum load specification of the resistance load.
● After the CPU module is powered on or is reset, the time taken to enter the RUN status varies
depending on the system configuration, parameter settings, and/or program size.
Design circuits so that the entire system will always operate safely, regardless of this variation in time.
● Simultaneously turn on and off the power supplies of the CPU module and extension modules.
● If a long-time power failure or an abnormal voltage drop occurs, the PLC stops, and output is turned
off. When the power supply is restored, it will automatically restart (when the RUN/STOP/RESET
switch is on RUN side).
[INSTALLATION PRECAUTIONS]
WARNING
● Make sure to cut off all phases of the power supply externally before attempting installation or wiring
work. Failure to do so may cause electric shock or damage to the product.
● Use the product within the generic environment specifications described in Page 17 Generic
Specifications of this manual.
Never use the product in areas with excessive dust, oily smoke, conductive dusts, corrosive gas (salt
air, Cl2, H2S, SO2 or NO2), flammable gas, vibration or impacts, or expose it to high temperature,
condensation, or rain and wind.
If the product is used in such conditions, electric shock, fire, malfunctions, deterioration or damage
may occur.
2
[INSTALLATION PRECAUTIONS]
CAUTION
● Do not touch the conductive parts of the product directly. Doing so may cause device failures or
malfunctions.
● When drilling screw holes or wiring, make sure that cutting and wiring debris do not enter the
ventilation slits of the PLC. Failure to do so may cause fire, equipment failures or malfunctions.
● For product supplied together with a dust proof sheet, the sheet should be affixed to the ventilation
slits before the installation and wiring work in order to block foreign objects such as cutting and wiring
debris.
However, when the installation work is completed, make sure to remove the sheet to provide
adequate ventilation. Failure to do so may cause fire, equipment failures or malfunctions.
● Install the product on a flat surface. If the mounting surface is rough, undue force will be applied to the
PC board, thereby causing nonconformities.
● Install the product securely using a DIN rail or mounting screws.
● Connect the expansion board and expansion adapter securely to their designated connectors. Loose
connections may cause malfunctions.
● Make sure to affix the expansion board with tapping screws. Tightening torque should follow the
specifications in the manual. If the screws are tightened outside of the specified torque range, poor
connections may cause malfunctions.
● Work carefully when using a screwdriver during product installation. Failure to do so may cause
damage to the product or accidents.
● Connect the extension cables, peripheral device cables, input/output cables and battery connecting
cable securely to their designated connectors. Loose connections may cause malfunctions.
● When using an SD memory card, insert it into the SD memory card slot. Check that it is inserted
completely. Poor contact may cause malfunction.
● Turn off the power to the PLC before attaching or detaching the following devices. Failure to do so
may cause device failures or malfunctions.
- Peripheral devices, expansion board and expansion adapter
- Extension modules and bus conversion module
- Battery
3
[WIRING PRECAUTIONS]
WARNING
● Make sure to cut off all phases of the power supply externally before attempting installation or wiring
work. Failure to do so may cause electric shock or damage to the product.
● Make sure to attach the terminal cover, provided as an accessory, before turning on the power or
initiating operation after installation or wiring work. Failure to do so may cause electric shock.
● The temperature rating of the cable should be 80 or more.
● Make sure to wire the screw terminal block in accordance with the following precautions. Failure to do
so may cause electric shock, equipment failures, a short-circuit, wire breakage, malfunctions, or
damage to the product.
- Wire terminals should follow the dimensions described in the manual.
- Tightening torque should follow the specifications in the manual.
- Tighten the screws using a Phillips-head screwdriver No. 2 (shaft diameter 6 mm (0.24") or less).
Make sure that the screwdriver does not touch the partition part of the terminal block.
● Make sure to wire the terminal block (European type) in accordance with the following precautions.
Failure to do so may cause electric shock, equipment failures, a short-circuit, wire breakage,
malfunctions, or damage to the product.
- Wire terminals should follow the dimensions described in the manual.
- Tightening torque should follow the specifications in the manual.
- Twist the ends of stranded wires and make sure that there are no loose wires.
- Do not solder-plate the electric wire ends.
- Do not connect more than the specified number of wires or electric wires of unspecified size.
- Affix the electric wires so that neither the terminal block nor the connected parts are directly
stressed.
[WIRING PRECAUTIONS]
CAUTION
● Do not supply power to the [24+] and [24V] terminals (24 V DC service power supply) on the CPU
module or extension modules. Doing so may cause damage to the product.
● Perform class D grounding (grounding resistance: 100  or less) of the grounding terminal on the
CPU module and extension modules with a wire 2 mm2 or thicker.
However, do not use common grounding (refer to Page 78 Grounding) with heavy electrical
systems.
● Connect the power supply wiring to the dedicated terminals described in this manual. If an AC power
supply is connected to a DC input/output terminal or DC power supply terminal, the PLC will burn out.
● Do not wire vacant terminals externally. Doing so may cause damage to the product.
● Install module so that excessive force will not be applied to terminal blocks, power connectors, I/O
connectors, communication connectors, or communication cables. Failure to do so may result in wire
damage/breakage or PLC failure.
4
CAUTION
● Make sure to observe the following precautions in order to prevent any damage to the machinery or
accidents due to malfunction of the PLC caused by abnormal data written to the PLC due to the
effects of noise.
- Do not bundle the power line, control line and communication cables together with or lay them
close to the main circuit, high-voltage line, load line or power line. As a guideline, lay the power
line, control line and connection cables at least 100 mm (3.94") away from the main circuit, high-
voltage line, load line or power line.
- Ground the shield of the shield wire or shielded cable at one point on the PLC. However, do not
use common grounding with heavy electrical systems.
- Ground the shield of the analog input/output cable at one point on the signal receiving side. Do
not use common grounding with heavy electrical systems.
[STARTUP AND MAINTENANCE PRECAUTIONS]

WARNING
● Do not touch any terminal while the PLC's power is on. Doing so may cause electric shock or
malfunctions.
● Before cleaning or retightening terminals, cut off all phases of the power supply externally. Failure to
do so may cause electric shock.
● Before modifying the program in mid-operation, forcing output, running or stopping the PLC, read
through this manual carefully, and ensure complete safety. An operation error may damage the
machinery or cause accidents.
● Do not change the program in the PLC from two or more peripheral equipment devices at the same
time. (i.e. from an engineering tool and a GOT) Doing so may cause destruction or malfunction of the
PLC program.
● Use the battery for memory backup in conformance to this manual.
- Use the battery for the specified purpose only.
- Connect the battery correctly.
- Do not charge, disassemble, heat, put in fire, short-circuit, connect reversely, weld, swallow or
burn the battery, or apply excessive force (vibration, impact, drop, etc.) to the battery.
- Do not store or use the battery at high temperatures or expose to direct sunlight.
- Do not expose to water, bring near fire or touch liquid leakage or other contents directly.
Incorrect handling of the battery may cause excessive heat, bursting, ignition, liquid leakage or
deformation, and lead to injury, fire or failures and malfunction of facilities and other equipment.
5
[STARTUP AND MAINTENANCE PRECAUTIONS]

CAUTION
● Do not disassemble or modify the PLC. Doing so may cause fire, equipment failures, or malfunctions.
*For repair, contact your local Mitsubishi Electric representative.
● After the first use of the SD memory card, do not insert/remove the memory card more than 500 times.
Insertion/removal 500 times or more may cause malfunction.
● Turn off the power to the PLC before connecting or disconnecting any extension cable. Failure to do
so may cause device failures or malfunctions.
● Turn off the power to the PLC before attaching or detaching the following devices. Failure to do so
may cause device failures or malfunctions.
- Peripheral devices, expansion board and expansion adapter
- Extension modules and bus conversion module
- Battery
[OPERATION PRECAUTIONS]
CAUTION
● Construct an interlock circuit in the program to ensure safe operation for the whole system when
executing control (for data change) of the PLC in operation. Read the manual thoroughly and ensure
complete safety before executing other controls (for program change, parameter change, forced
output and operation status change) of the PLC in operation. Otherwise, the machine may be
damaged and accidents may occur by erroneous operations.
[DISPOSAL PRECAUTIONS]
CAUTION
● Please contact a certified electronic waste disposal company for the environmentally safe recycling
and disposal of your device.
● When disposing of batteries, separate them from other waste according to local regulations. For
details on the Battery Directive in EU countries, refer to Page 144 Handling of Batteries and
Devices with Built-in Batteries in EU Member States.
6
[TRANSPORTATION PRECAUTIONS]
CAUTION
● When transporting the PLC with the optional battery, turn on the PLC before shipment, confirm that
the battery mode is set in PLC parameters and the BAT LED is OFF, and check the battery life. If the
PLC is transported with the BAT LED on or the battery exhausted, the battery-backed data may be
lost during transportation.
● The PLC is a precision instrument. During transportation, avoid impacts larger than those specified in
the general specifications (Page 17 Generic Specifications) by using dedicated packaging boxes
and shock-absorbing palettes. Failure to do so may cause failures in the PLC. After transportation,
verify operation of the PLC and check for damage of the mounting part, etc.
● When transporting lithium batteries, follow required transportation regulations. For details on the
regulated products, refer to Page 144 Handling of Batteries and Devices with Built-in Batteries in
EU Member States.
● Fumigants that contain halogen materials such as fluorine, chlorine, bromine, and iodine used for
disinfecting and protecting wooden packaging from insects will cause malfunction in Mitsubishi
products. Please take necessary precautions to ensure that residual fumigants do not enter the
product, or treat packaging with methods other than fumigation (heat method). Additionally, disinfect
and protect wood from insects before packing.
INTRODUCTION
This manual contains text, diagrams and explanations which will guide the reader in the correct installation, safe use and
operation of the FX5U Programmable Controllers and should be read and understood before attempting to install or use the
module.
Always forward it to the end user.
Regarding use of this product

• This product has been manufactured as a general-purpose part for general industries, and has not been designed or
manufactured to be incorporated in a device or system used in purposes related to human life.
• Before using the product for special purposes such as nuclear power, electric power, aerospace, medicine or passenger
movement vehicles, consult Mitsubishi Electric.
• This product has been manufactured under strict quality control. However when installing the product where major
accidents or losses could occur if the product fails, install appropriate backup or failsafe functions in the system.
Note
• If in doubt at any stage during the installation of the product, always consult a professional electrical engineer who is
qualified and trained in the local and national standards. If in doubt about the operation or use, please consult the nearest
Mitsubishi Electric representative.
• Since the examples indicated by this manual, technical bulletin, catalog, etc. are used as a reference, please use it after
confirming the function and safety of the equipment and system. Mitsubishi Electric will accept no responsibility for actual
use of the product based on these illustrative examples.
• This manual content, specification etc. may be changed, without a notice, for improvement.
• The information in this manual has been carefully checked and is believed to be accurate; however, if you notice a doubtful
point, an error, etc., please contact the nearest Mitsubishi Electric representative. When doing so, please provide the
manual number given at the end of this manual.
7
CONTENTS
SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
RELEVANT MANUALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
TERMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
CHAPTER 1 OUTLINE 14
1.1 Part Names. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
CHAPTER 2 SPECIFICATIONS 17
2.1 Generic Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.2 Power Supply Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
AC power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.3 Input Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
24 V DC Input (sink/source) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.4 Output Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Relay output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Transistor output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.5 Input/Output Derating Curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.6 Performance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2.7 Built-in Analog Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Analog input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Analog output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
2.8 Communication Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Built-in Ethernet communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Built-in RS-485 communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
2.9 External Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
CPU module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
2.10 Terminal Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
CHAPTER 3 PRODUCT LIST 31

3.1 Overall Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.2 CPU Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.3 I/O Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.4 Intelligent Function Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
FX5 intelligent Function Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
FX3 intelligent Function Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.5 Expansion Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.6 Expansion Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.7 Extension Power Supply Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
FX5 expansion power supply module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
FX3 expansion power supply module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3.8 Bus Conversion Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3.9 SD Memory Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3.10 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
3.11 Communication Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
3.12 Engineering Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
8
CHAPTER 4 SYSTEM CONFIGURATION 38

4.1 Rules of System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.2 Limitations on the Number of Connected Extension Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Number of connected expansion boards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Number of connected expansion adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Number of connected extension modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
4.3 Limitation on the Number of Input/Output Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Total number of I/O points and remote I/O points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Calculation of number of input/output points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
CONTENTS
Calculation of number of remote I/O points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.4 Limitation on Current Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Power supply check from the CPU module (current consumption calculation) . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Power supply check from the powered input/output module (current consumption calculation) . . . . . . . . . . . . . 49
Power supply check from extension power supply module (current consumption calculation) . . . . . . . . . . . . . . 51
4.5 Rules of System Configuration and Examples of Reconfiguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
System configuration example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
System reconfiguration example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
4.6 Numbers and Assignment in System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Module input/output number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Module number of Extension modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
CHAPTER 5 INSTALLATION 63
5.1 Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Installation location in enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Spaces in enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Layout in enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
5.2 Examination for Installation Method in Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
5.3 Procedures for Installing on and Detaching from DIN Rail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Preparation for installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Installation of CPU module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Installation of extension module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Removal of CPU module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
5.4 Procedures for Installing Directly (with M4 Screws) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Hole pitches for direct mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Hole pitches when extension module connected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Installation of CPU module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Installation of extension module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
5.5 Connection Methods for CPU Module and Extension Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Connection of extension devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Connection method A - connection of an expansion board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Connection method B - connection of an expansion adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Connection method C - connection of an extension module to the CPU module . . . . . . . . . . . . . . . . . . . . . . . . 72
Connection method D - connection between extension modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Connection method E - connection of an extension module to the bus conversion module . . . . . . . . . . . . . . . . 73
CHAPTER 6 WIRING 74
6.1 Wiring Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Wiring procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Removal and installation of removable terminal block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
6.2 Cable Connecting Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
9
Screw terminal block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

European-type terminal block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
6.3 Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
6.4 Power Supply Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Examples of AC power supply wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
6.5 Input Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
24 V DC input (Sink and source input type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Input wiring example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
6.6 Output Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Relay output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Transistor output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Output wiring example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
6.7 Analog Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
6.8 Examples of Wiring for Various Uses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Built-in positioning function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Communication function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
High-speed counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Interruption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Digital Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Input Matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Seven Segment with Latch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
CHAPTER 7 OPERATION ADJUSTMENT 110

7.1 Preparation for Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Preliminary inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Procedure until operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Connection with a personal computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
7.2 Operation and Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Self-diagnostic function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Monitoring and debugging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
7.3 Running, Stopping, and Resetting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Methods of running, stopping, and resetting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
CHAPTER 8 MAINTENANCE AND INSPECTION 115

8.1 Daily Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
8.2 Periodic Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
8.3 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Part names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Battery attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Battery replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Special relay for low battery voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
CHAPTER 9 TROUBLESHOOTING 120

9.1 Troubleshooting Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
9.2 Checking with LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Checking the PWR LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Checking the BAT LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Checking the ERR LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Checking the P.RUN LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
10
9.3 Troubleshooting using the engineering tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

Module diagnostics (CPU Diagnostics) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
9.4 Error Status and Operations on Occurrence of an Error. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
9.5 Backing Up the Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
9.6 Canceling Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
9.7 Troubleshooting for Each Symptom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
I/O operation (CPU module, I/O module) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
PLC write, PLC read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Boot operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
CONTENTS
APPENDIX 127
Appendix 1 How to Check the Date of Manufacture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Appendix 2 Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Certification of UL, cUL standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Compliance with EC directive (CE Marking) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Requirement for compliance with EMC directive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Requirement for compliance with LVD directive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Caution for compliance with EC Directive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Appendix 3 I/O Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Product configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Product list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
External dimensions and component names. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Terminal layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Appendix 4 SD Memory Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Part names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Insertion and removal of the SD memory card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Appendix 5 Precautions for Battery Transportation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Control-subject product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Precautions for transportation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Appendix 6 Handling of Batteries and Devices with Built-in Batteries in EU Member States . . . . . . . . . . . . . . 144
Disposal precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Exportation precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
INDEX 145
REVISIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147
TRADEMARKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148
11
RELEVANT MANUALS
User's manuals for the applicable modules
Manual name <manual number> Description

MELSEC iQ-F FX5U CPU Module Hardware Manual Describes the details of input/output specifications, wiring and installation of the
<JY997D53401> FX5U CPU module from MELSEC iQ-F FX5U User's Manual (Hardware).
MELSEC iQ-F FX5 User's Manual (Startup) Performance specifications, procedures before operation, and troubleshooting of the
<JY997D58201> CPU module.
MELSEC iQ-F FX5U User's Manual (Hardware) Describes the details of hardware of the FX5U CPU module, including input/output
<JY997D55301> (This manual) specifications, wiring, installation, and maintenance.
MELSEC iQ-F FX5UC User's Manual (Hardware) Describes the details of hardware of the FX5UC CPU module, including input/output
<JY997D61401> specifications, wiring, installation, and maintenance.
MELSEC iQ-F FX5 User's Manual (Application) Describes basic knowledge required for program design, functions of the CPU
<JY997D55401> module, devices/labels, and parameters.
MELSEC iQ-F FX5 Programming Manual (Program Design) Describes specifications of ladders, ST, FBD/LD, and other programs and labels.
<JY997D55701>
MELSEC iQ-F FX5 Programming Manual (Instructions, Standard Describes specifications of instructions and functions that can be used in programs.
Functions/Function Blocks)
<JY997D55801>
MELSEC iQ-F FX5 User's Manual (Serial Communication) Describes N:N network, MELSEC Communication protocol, inverter communication,
<JY997D55901> non-protocol communication, and predefined protocol support.
MELSEC iQ-F FX5 User's Manual (MODBUS Communication) Describes MODBUS serial communication.
<JY997D56101>
MELSEC iQ-F FX5 User's Manual (Ethernet Communication) Describes the functions of the built-in Ethernet port communication function.
<JY997D56201>
MELSEC iQ-F FX5 User's Manual (SLMP) Explains methods for the device that is communicating with the CPU module by
<JY997D56001> SLMP to read and write the data of the CPU module.
MELSEC iQ-F FX5 User's Manual (Positioning Control) Describes the built-in positioning function.
<JY997D56301>
MELSEC iQ-F FX5 User's Manual (Analog Control) Describes the analog function.
<JY997D60501>
GX Works3 Operating Manual System configuration, parameter settings, and online operations of GX Works3.
<SH-081215ENG>
TERMS
Unless otherwise specified, this manual uses the following terms.
•  indicates a variable part to collectively call multiple models or versions.
(Example) FX5U-32MR/ES, FX5U-32MT/ES  FX5U-32M/ES
• For details on the FX3 devices that can be connected with the FX5U CPU module, refer to Page 31 PRODUCT LIST.
Terms Description
■Devices
FX5 Generic term for FX5U, and FX5UC PLCs
FX3 Generic term for FX3S, FX3G, FX3GC, FX3U, and FX3UC PLCs
FX5 CPU module Generic term for FX5U CPU module and FX5UC CPU module
FX5U CPU module Generic term for FX5U-32MR/ES, FX5U-32MT/ES, FX5U-32MT/ESS, FX5U-64MR/ES, FX5U-64MT/ES,
FX5U-64MT/ESS, FX5U-80MR/ES, FX5U-80MT/ES, and FX5U-80MT/ESS
FX5UC CPU module Generic term for FX5UC-32MT/D and FX5UC-32MT/DSS
Extension module Generic term for FX5 extension modules and FX3 function modules
• FX5 extension module Generic term for I/O modules, FX5 extension power supply module, and FX5 intelligent function module
• FX3 extension module Generic term for FX3 extension power supply module and FX3 intelligent function module
I/O module Generic term for input modules, output modules, and powered input/output modules
• Input module Generic term for FX5-8EX/ES and FX5-16EX/ES
• Output module Generic term for FX5-8EYR/ES, FX5-8EYT/ES, FX5-8EYT/ESS, FX5-16EYR/ES, FX5-16EYT/ES, and
FX5-16EYT/ESS
Powered input/output module Generic term for FX5-32ER/ES, FX5-32ET/ES, and FX5-32ET/ESS
12
Terms Description
Extension power supply module Generic term for FX5 extension power supply module and FX3 extension power supply module
• FX5 extension power supply module Different name for FX5-1PSU-5V
• FX3 extension power supply module Different name for FX3U-1PSU-5V
Intelligent module The abbreviation for intelligent function modules
Intelligent function module Generic term for FX5 intelligent function modules and FX3 intelligent function modules
• FX5 intelligent function module Generic term for FX5 intelligent function modules
• FX3 intelligent function module Different name for FX3 special function blocks
Simple motion module Different name for FX5-40SSC-S
Expansion board Generic term for board for FX5U CPU module
• Communication board Generic term for FX5-232-BD, FX5-485-BD, and FX5-422-BD-GOT
Expansion adapter Generic term for adapter for FX5 CPU module
• Communication adapter Generic term for FX5-232ADP and FX5-485ADP
• Analog adapter Generic term for FX5-4AD-ADP and FX5-4DA-ADP
Bus conversion module Different name for FX5-CNV-BUS
Battery Different name for FX3U-32BL
SD memory card Generic term for NZ1MEM-2GBSD, NZ1MEM-4GBSD, L1MEM-2GBSD and L1MEM-4GBSD SD memory
cards
Abbreviation of Secure Digital Memory Card. Device that stores data using flash memory.
Peripheral device Generic term for engineering tools and GOTs
GOT Generic term for Mitsubishi Graphic Operation Terminal GOT1000 and GOT2000 series
■Software packages
Engineering tool The product name of the software package for the MELSEC programmable controllers
GX Works3 The product name of the software package, SWnDND-GXW3, for the MELSEC programmable controllers
(The 'n' represents a version.)
■Manuals
Hardware manual Generic term for manuals enclosed with the product
• FX5U Hardware manual Abbreviation of MELSEC iQ-F FX5U CPU Module Hardware manual
User's manual Generic term for separate manuals
• User's manual (Startup) Abbreviation of MELSEC iQ-F FX5 User's Manual (Startup)
• FX5U User's manual (Hardware) Abbreviation of MELSEC iQ-F FX5U User's Manual (Hardware)
• User's manual (Application) Abbreviation of MELSEC iQ-F FX5 User's Manual (Application)
Programming manual (Program Design) Abbreviation of MELSEC iQ-F FX5 Programming Manual (Program Design)
Programming manual (Instructions, Standard Abbreviation of MELSEC iQ-F FX5 Programming Manual (Instructions, Standard Functions/Function Blocks)
Functions/Function Blocks)
Communication manual Generic term for MELSEC iQ-F FX5 User's Manual (Serial Communication), MELSEC iQ-F FX5 User's
Manual (MODBUS Communication), MELSEC iQ-F FX5 User's Manual (Ethernet Communication), and
MELSEC iQ-F FX5 User's Manual (SLMP)
• Serial communication manual Abbreviation of MELSEC iQ-F FX5 User's Manual (Serial Communication)
• MODBUS communication manual Abbreviation of MELSEC iQ-F FX5 User's Manual (MODBUS Communication)
• Ethernet communication manual Abbreviation of MELSEC iQ-F FX5 User's Manual (Ethernet Communication)
• SLMP manual Abbreviation of MELSEC iQ-F FX5 User's Manual (SLMP)
Positioning manual Abbreviation of MELSEC iQ-F FX5 User's Manual (Positioning Control)
Analog manual Abbreviation of MELSEC iQ-F FX5 User's Manual (Analog Control)
13
1 OUTLINE
1.1 Part Names

Front panel
[2]
[3] [7]
[6] [8]
[9]
[5] [10]
[4]
[11]
[3]
[2]
[1]
No. Name Description
[1] DIN rail mounting hooks Hook for mounting the CPU module on a DIN rail of DIN46277 (35 mm (1.38") wide).
[2] Expansion adapter connecting When connecting an expansion adapter, secure it with these hooks.
hooks
[3] Terminal block cover Cover for protecting the terminal block.
The cover can be opened for wiring. Keep the covers closed while equipment is running (power is on).
[4] Built-in Ethernet communication Connector for connection with Ethernet-compatible devices. (with cover)
connector For details, refer to MELSEC iQ-F FX5 User's Manual (Ethernet Communication).
[5] Top cover Cover for protecting the SD memory card slot, the RUN/STOP/RESET switch, and others.
The built-in RS-485 communication terminal block, built-in analog I/O terminal block, RUN/STOP/RESET switch,
SD memory card slot, and others are located under this cover.
[6] CARD LED Indicates whether an SD memory card can be used or not.
Lit: Can be used or cannot be removed.
Flashing: In preparation
Off: Not inserted or can be removed.
RD LED Lit when the CPU module is receiving data through built-in RS-485 communication.
SD LED Lit when the CPU module is sending data through built-in RS-485 communication.
SD/RD LED Lit when the CPU module is sending or receiving data through built-in Ethernet communication.
[7] Expansion board connector cover Cover for protecting expansion board connectors, battery, or others.
Connect the battery under this cover.
[8] Input display LED Lit when input is on.
[9] Extension connector cover Cover for protecting the extension connector.
Connect the extension cable of an extension module to the extension connector under the cover.
[10] PWR LED Indicates whether the CPU module is powered or not.
Lit: Powered
Off: Not powered or hardware error (Page 120 Checking with LEDs)
ERR LED Indicates the error status of the CPU module. (Page 120 Checking with LEDs)
Lit: Error or hardware error
Flashing: Factory default setting, error, hardware error, or resetting
Off: Operating normally
P.RUN LED Indicates the program running status.
Lit: Operating normally
Flashing: Paused
Off: Stopped or stop error
BAT LED Indicates the battery status.
Flashing: Battery error
Off: Operating normally (Page 120 Checking with LEDs)
[11] Output display LED Lit when output is on.
1 OUTLINE
14 1.1 Part Names
With cover open

1
[6]
[5] [7]
[4] [8]
[3] [9]
[2]
[10]
[1]

[1] Built-in RS-485 communication Terminal block for connection with RS-485-compatible devices
terminal block
[2] RS-485 terminal resistor selector Switch for switching terminal resistance for built-in RS-485 communication.
switch
[3] RUN/STOP/RESET switch Switch for operating the CPU module. (Page 114 Methods of running, stopping, and resetting)
RUN: Runs the program
STOP: Stops the program
RESET: Resets the CPU module (hold the switch on the RESET side for approximately 1 second.)
[4] SD memory card disable switch Switch for disabling access to the SD memory card when the card is to be removed.
[5] Built-in analog I/O terminal block Terminal block for using the built-in analog function.
[6] SD memory card slot Slot for inserting an SD memory card.
[7] Expansion board connector Connector for connecting an expansion board.
[8] Extension connector Connector for connecting the extension cable of an extension module.
[9] Battery holder Holder for storing an optional battery.
[10] Battery connector Connector for connecting an optional battery.
Use a tool such as a screwdriver to operate RS-485 terminal resistor selector switch.
Make sure that the edge of the tool does not damage the switch or the case.
When the terminal block covers are open

[1]
[2]
[2]
[1]
[1] Terminal block mounting screws Gradually loosen the left and right screws (alternately), and remove the top of the terminal blocks.
[2] Terminal Terminals for power, input, and output.
For details on the terminal layout, refer to Page 28 Terminal Layout.
1 OUTLINE
1.1 Part Names 15
Side
Left side/right side

Left side Right side
[1]
[2]
[3]
[4]
[1] Expansion adapter connector cover Cover for protecting the expansion adapter connector. Connect the expansion adapter to the expansion
adapter connector under the cover.
[2] Genuine product certification label Genuine product certification label to prevent counterfeiting
[3] Nameplate The product model name, Manufacturer's serial number, power supply specifications, and MAC address are
shown.
[4] DIN rail mounting groove The module can be installed on DIN46277 rail (35 mm (1.38") wide).
Products that do not have the genuine product certification label or nameplate are not covered by the
warranty.
Top side/bottom side

Top side Bottom side
[1]
[1]
[1] CPU module fixing screw hole Screw holes for fixing the CPU module to the panel. (In the case of FX5U-64M/80M, there are four
screw holes.)
1 OUTLINE
16 1.1 Part Names
2 SPECIFICATIONS
The CPU module specifications are explained below.
2.1 Generic Specifications 2

Item Specifications
*1
Operating ambient temperature 0 to 55 (32 to 131 )*2
Storage ambient temperature -25 to 75 (-13 to 167 )
Operating ambient humidity 5 to 95%RH, non-condensation
Storage ambient humidity 5 to 95%RH, non-condensation
Vibration resistance*3*4  Frequency Acceleration Half amplitude Sweep count
Installed on DIN rail 5 to 8.4 Hz  1.75 mm 10 times each in X, Y, Z directions
(80 min in each direction)
8.4 to 150 Hz 4.9 m/ 
Direct installing 5 to 8.4 Hz  3.5 mm
8.4 to 150 Hz 9.8 m/ 
Shock resistance*3 147 m/, Action time: 11 ms, 3 times by half-sine pulse in each direction X, Y, and Z
Noise durability By noise simulator at noise voltage of 1000 Vp-p, noise width of 1 s and period of 30 to 100 Hz
Grounding Class D grounding (grounding resistance: 100  or less) <Common grounding with a heavy electrical system is not
allowed.>*5
Working atmosphere Free from corrosive or flammable gas and excessive conductive dust
Operating altitude*6 0 to 2000 m
Installation location Inside a control panel
Overvoltage category*7  or less
Pollution degree*8 2 or less
Equipment class Class 2
*1 The simultaneous ON ratio of available PLC inputs or outputs changes with respect to the ambient temperature, refer to Page 22
Input/Output Derating Curve.
*2 For details on Intelligent function modules, refer to manuals of each product.
*3 The criterion is shown in IEC61131-2.
*4 When the system has equipment which specification values are lower than above mentioned vibration resistance specification values,
the vibration resistance specification of the whole system is corresponding to the lower specification.
*5 For grounding, refer to Page 78
*6 The PLC cannot be used at a pressure higher than the atmospheric pressure to avoid damage.
*7 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power
distribution network and the machinery within premises. Category  applies to equipment for which electrical power is supplied from
fixed facilities. The surge voltage withstand level for up to the rated voltage of 300 V is 2500 V.
*8 This index indicates the degree to which conductive material is generated in the environment in which the equipment is used. Pollution
level 2 is when only non-conductive pollution occurs. Temporary conductivity caused by condensation must be expected occasionally.
Dielectric withstand voltage test and insulation resistance test

Perform dielectric withstand voltage test and insulation resistance test at the following voltages between each terminal and
the CPU module ground terminal.
■ CPU module, I/O module

Between terminals Dielectric Insulation resistance Remarks
withstand voltage
Between power supply terminal (AC power supply) and ground terminal 1.5 kV AC for one 10 M or higher by 500 V DC 
minute insulation resistance tester
Between 24 V DC service power supply connected to input terminal (24 500 V AC for one 
V DC) and ground terminal minute
Between output terminal (relay) and ground terminal 1.5 kV AC for one 
minute
Between output terminal (transistor) and ground terminal 500 V AC for one 
minute
2 SPECIFICATIONS
2.1 Generic Specifications 17
■Expansion board, expansion adapter

Between terminals Dielectric Insulation resistance Remarks
withstand
voltage
Between terminal of expansion board and ground terminal Not allowed Not allowed Since the expansion board and
CPU module are not insulated, it
is not allowed to perform the
dielectric withstand voltage test
and insulation resistance test
between them.
Between terminal of expansion adapter and ground terminal 500 V AC for 10 M or higher by 500 V DC 
one minute insulation resistance tester
For dielectric withstand voltage test and insulation resistance test of each product, refer to manuals of each product.
■Intelligent function module

For information concerning dielectric withstand voltage and insulation resistance of intelligent function modules, refer to
manuals of each intelligent function module.
2.2 Power Supply Specifications

The CPU module power supply specifications are explained below.
For the consumption current of extension modules, refer to Page 31 PRODUCT LIST or manuals of each extension
module.
AC power supply
Item Specifications
Rated voltage 100 to 240 V AC
Allowable supply voltage range 85 to 264 V AC
Frequency rating 50/60 Hz
Allowable instantaneous power failure time Operation can be continued upon occurrence of instantaneous power failure for 10 ms or less.
When the supply voltage is 200 V AC, the time can be change to 10 to 100 ms by editing the user
program.
Power fuse FX5U-32M 250 V, 3.15 A Time-lag fuse
FX5U-64M, 250 V, 5 A Time-lag fuse
FX5U-80M
Rush current FX5U-32M 25 A max. 5 ms or less/100 V AC
50 A max. 5 ms or less/200 V AC
FX5U-64M, 30 A max. 5 ms or less/100 V AC
FX5U-80M 60 A max. 5 ms or less/200 V AC
Power consumption*1 FX5U-32M 30 W
FX5U-64M 40 W
FX5U-80M 45 W
24 V DC service power FX5U-32M 400 mA (Supply capacity when service power supply is used for input circuit of the CPU module )
supply capacity*2 480 mA (Supply capacity when external power supply is used for input circuit of the CPU module)
FX5U-64M 600 mA (Supply capacity when service power supply is used for input circuit of the CPU module)
740 mA (Supply capacity when external power supply is used for input circuit of the CPU module)
FX5U-80M 600 mA (Supply capacity when service power supply is used for input circuit of the CPU module)
770 mA (Supply capacity when external power supply is used for input circuit of the CPU module)
5 V DC power supply FX5U-32M 900 mA
capacity
FX5U-64M, 1100 mA
FX5U-80M
*1 This item shows value when all 24 V DC service power supplies are used in the maximum configuration connectable to the CPU
module. (The current of the input circuit is included.)
*2 When I/O modules are connected, they consume current from the 24 V DC service power.
For details on the service power supply, refer to Page 48 Limitation on Current Consumption.
2 SPECIFICATIONS
18 2.2 Power Supply Specifications
2.3 Input Specifications

The CPU module input specifications are explained below.
24 V DC Input (sink/source)
2
The input points in the table below indicate the CPU module terminal points.
Item Specifications
No. of input points FX5U-32M 16 points
FX5U-64M 32 points
FX5U-80M 40 points
Connection type Removable terminal block (M3 screws)
Input type Sink/source
Input signal voltage 24 V DC +20 %, -15%
Input signal current X000 to X017 5.3 mA/24 V DC
X020 and subsequent 4.0 mA/24 V DC
Input impedance X000 to X017 4.3 k
X020 and subsequent 5.6 k
ON input sensitivity X000 to X017 3.5 mA or more
current
X020 and subsequent 3.0 mA or more
OFF input sensitivity current 1.5 mA or less
Input response FX5U-32M X000 to X005 200 kHz
frequency When capturing pulses of a response frequency of 50 to 200 kHz, refer to Page 86 In the case of
FX5U-64M, X000 to X007
capturing high-speed pulses.
FX5U-80M
FX5U-32M X006 to X017 10 kHz
FX5U-64M, X010 to X017
FX5U-80M
Pulse waveform Waveform T1 T1
T2 T2
T1 (pulse width) T2 (rise/fall time)

FX5U-32M X000 to X005 2.5 s or more 1.25 s or less
FX5U-64M, X000 to X007
FX5U-80M
FX5U-32M X006 to X017 50 s or more 25 s or less
FX5U-64M, X010 to X017
FX5U-80M
Input response time FX5U-32M X000 to X005 ON: 2.5 s or less
(H/W filter delay) OFF: 2.5 s or less
FX5U-64M, X000 to X007
FX5U-80M
FX5U-32M X006 to X017 ON: 30 s or less
FX5U-64M, X010 to X017 OFF: 50 s or less
FX5U-80M
FX5U-64M, X020 and ON: 50 s or less
FX5U-80M subsequent OFF: 150 s or less
Input response time None, 10 s, 50 s, 0.1 ms, 0.2 ms, 0.4 ms, 0.6 ms, 1 ms, 5 ms, 10 ms (initial values), 20 ms, 70 ms
(Digital filter setting value) When using this product in an environment with much noise, set the digital filter.
Input signal format No-voltage contact input
Sink: NPN open collector transistor
Source: PNP open collector transistor
Input circuit insulation Photo-coupler insulation
Indication of input operation LED is lit when input is on
2 SPECIFICATIONS
2.3 Input Specifications 19
Item Specifications
Input circuit configuration • When using service power supply
Sink input wiring Source input wiring
Fuse Fuse
L L
N N
100 to 240 V AC 100 to 240 V AC
24V 24V
0V 0V
S/S S/S
X X
Input impedance Input impedance
• When using external power supply

Fuse Fuse
L L
N N
100 to 240 V AC 100 to 240 V AC
24V 24V
0V 0V
S/S S/S
X X
Input impedance Input impedance
2 SPECIFICATIONS
20 2.3 Input Specifications
2.4 Output Specifications

The CPU module output specifications are explained below.
Relay output
2
Item Output Specifications
No. of output points FX5U-32MR/ 16 points
FX5U-64MR/ 32 points
FX5U-80MR/ 40 points
Output type Relay
External power supply 30 V DC or less
240 V AC or less ("250 V AC or less" if not a CE, UL, cUL compliant item)
Max. load 2 A/point
The total load current per common terminal should be the following value.
• 4 output points/common terminal: 8 A or less
For details on the common, refer to Page 29 Interpretation of terminal block layout.
Min. load 5 V DC, 2 mA (reference values)
Open circuit leakage current 
Response time OFFON Approx. 10 ms
ONOFF Approx. 10 ms
Insulation of circuit Mechanical insulation
Indication of output operation LED is lit when output is on
Output circuit configuration
Load
Y
DC power supply
COM
Fuse
Load
Y
AC power supply
COM
Fuse
A number is entered in the of [COM ].
2 SPECIFICATIONS
2.4 Output Specifications 21
Transistor output
Item Output specifications
No. of output points FX5U-32MT/ 16 points
FX5U-64MT/ 32 points
FX5U-80MT/ 40 points
Output type FX5U-MT/ES Transistor/sink output
FX5U-MT/ESS Transistor/source output
External power supply 5 to 30 V DC
Max. load 0.5 A/point
The total load current per common terminal should be the following value.
• 4 output points/common terminal: 0.8 A or less
For details on the common, refer to Page 29 Interpretation of terminal block layout.
Open circuit leakage current 0.1 mA or less/30 V DC
Voltage drop when ON Y000 to Y003 1.0 V or less
Y004 and subsequent 1.5 V or less
Response time Y000 to Y003 2.5 s or less/10 mA or more (5 to 24 V DC)
Y004 and subsequent 0.2 ms or less/200 mA or more (24 V DC)
Insulation of circuit Photo-coupler insulation
Output circuit configuration Sink output wiring Source output wiring
Load Load
Y Y
DC power supply DC power supply
COM +V
Fuse Fuse
A number is entered in the of [COM ]. A number is entered in the of [+V ].
2.5 Input/Output Derating Curve

The derating curve below shows the simultaneous ON ratio of available PLC inputs or outputs with respect to the ambient
temperature. Use the PLC within the simultaneous input or output ON ratio range shown in the figure.
Derating curve
When service power supply or external power supply (24 V DC) is used for input circuits
Simultaneous ON ratio
100%
80%
applicable
50 55 Ambient temperature
2 SPECIFICATIONS
22 2.5 Input/Output Derating Curve
2.6 Performance Specifications

Item Specification
Control system Stored-program repetitive operation
Input/output control system Refresh system
(Direct access input/output allowed by specification of direct access input/output [DX, DY]) 2
Programming Programming language Ladder diagram (LD), structured text (ST), function block diagram/ladder diagram (FBD/LD)
specifications Programming extension function Function block (FB), structured ladder, label programming (local/global)
Constant scan 0.2 to 2000 ms (can be set in 0.1 ms increments)
Fixed cycle interrupt 1 to 60000 ms (can be set in 1 ms increments)
Timer performance specifications 100 ms, 10 ms, 1 ms
No. of program executions 32
No. of FB files 16 (Up to 15 for user)
Operation Execution type Standby type, initial execution type, scan execution type, event execution type
specifications
Interrupt type Internal timer interrupt, input interruption, high-speed comparison match interrupt
Command LD X0 34 ns
processing time
MOV D0 D1 34 ns
Memory Program capacity 64 k steps
capacity (128 kbytes, flash memory)
SD memory card Memory card capacity (SD/SDHC memory card: Max. 4 Gbytes)
Device/label memory 120 kbytes
Data memory/standard ROM 5 Mbytes
Flash memory (Flash ROM) write count Maximum 20000 times
File storage Device/label memory 1
capacity
Data memory P: 32, FB: 16
P: No. of program files
FB: No. of FB files
SD Memory Card 2 Gbytes: 511*1
4 Gbytes: 65534*1
Clock function Display data Year, month, day, hour, minute, second, day of week (leap year automatic detection)
Precision -2.96 to +3.74 (TYP.+1.42) s/d (Ambient temperature: 0 (32))
-3.18 to +3.74 (TYP.+1.50) s/d (Ambient temperature: 25 (77))
-13.20 to +2.12 (TYP.-3.54) s/d (Ambient temperature: 55 (131))
No. of input/ (1) No. of input/output points 256 points or less
output points
(2) No. of remote I/O points 384 points or less
Total No. of points of (1) and (2) 512 points or less
Power failure Retention method Large-capacity capacitor
retention*2
Retention time 10 days (Ambient temperature: 25 (77))
Data retained Clock data
*1 The value listed above indicates the number of files stored in the root folder.
*2 Clock data is retained using the power accumulated in a large-capacity capacitor incorporated into the PLC. When voltage of the large-
capacity capacitor drops, clock data is no longer accurately retained. The retention period of a fully charged capacitor (electricity is
conducted across the PLC for at least 30 minutes) is 10 days (ambient temperature: 25 (77)). How long the capacitor can hold the
data depends on the operating ambient temperature. When the operating ambient temperature is high, the holding period is short.
2 SPECIFICATIONS
2.6 Performance Specifications 23
Number of device points

Item Base Max. number of points
No. of user device Input relay (X) 8 1024 points The total number of X and Y assigned to input/output points is up to
points 256 points.
Output relay (Y) 8 1024 points
Internal relay (M) 10 32768 points (can be changed with parameter)*1
Latch relay (L) 10 32768 points (can be changed with parameter)*1
Link relay (B) 16 32768 points (can be changed with parameter)*1
Annunciator (F) 10 32768 points (can be changed with parameter)*1
Link special relay (SB) 16 32768 points (can be changed with parameter)*1
Step relay (S) 10 4096 points (fixed)
Timer system Timer (T) 10 1024 points (can be changed with parameter)*1
Accumulation Accumulation timer 10 1024 points (can be changed with parameter)*1
timer system (ST)
Counter Counter (C) 10 1024 points (can be changed with parameter)*1
system Long counter (LC) 10 1024 points (can be changed with parameter)*1
Data register (D) 10 8000 points (can be changed with parameter)*1
Link register (W) 16 32768 points (can be changed with parameter)*1
Link special register (SW) 16 32768 points (can be changed with parameter)*1
No. of system device Special relay (SM) 10 10000 points (fixed)
points
Special register (SD) 10 12000 points (fixed)
Module access device Intelligent function module device 10 65536 points (designated by U\G)
No. of index register Index register (Z)*2 10 24 points
points
Long index register (LZ)*2 10 12 points
No. of file register File register (R) 10 32768 points (can be changed with parameter)*1
points
No. of nesting points Nesting (N) 10 15 points (fixed)
No. of pointer points Pointer (P) 10 4096 points
Interrupt pointer (I) 10 178 points (fixed)
Others Decimal Signed  16 bits: -32768 to +32767, 32 bits: -2147483648 to +2147483647
constant (K) Unsigned  16 bits: 0 to 65535, 32 bits: 0 to 4294967295
Hexadecimal constant (H)  16 bits: 0 to FFFF, 32 bits: 0 to FFFFFFFF
Real constant Single precision  E-3.40282347+38 to E-1.17549435-38, 0, E1.17549435-38 to E3.40282347+38
(E)
Character string  Shift-JIS code max. 255 single-byte characters (256 including NULL)
*1 Can be changed with parameters within the capacity range of the CPU built-in memory.
*2 Total of the index register (Z) and long index register (LZ) is maximum 24 words.
2 SPECIFICATIONS
24 2.6 Performance Specifications
2.7 Built-in Analog Specifications

The analog input/output specifications of the built-in analog function are explained below.
For details on the analog built-in function, refer to MELSEC iQ-F FX5 User's Manual (Analog Control).
Analog input 2
Item Specifications
Analog input points 2 points (2 channels)
Analog input Voltage 0 to 10 V DC (input resistance 115.7 k)
Digital output Unsigned 12-bit binary
I/O characteristics, Maximum resolution Digital output value 0 to 4000
Maximum resolution 2.5 mV
Accuracy Ambient temperature Within 0.5% (20 digit*1)
(Accuracy in respect to maximum digital 25 5 (77 41)
output value) Ambient temperature Within 1.0% (40 digit*1)
0 to 55 (32 to 131)
Conversion speed 30 s /channels (data refreshed every operation cycle)
Absolute maximum input -0.5 V, +15 V
Insulation method Inside the PLC and the analog input circuit are not insulated. Between input terminals
(channels) is not insulated.
Occupied points 0 points (does not pertain to the max. No. of input/output points of the PLC.)
Terminal block used European-type terminal block
*1 "Digit" refers to digital values.
Analog output
Item Specifications
Analog output points 1 points (1 channels)
Digital input Unsigned 12-bit binary
Analog output Voltage 0 to 10 V DC (external load resistance 2 k to 1 M)
I/O characteristics, Maximum resolution*1 Digital input value 0 to 4000
Maximum resolution 2.5 mV
Accuracy*2 Ambient temperature Within 0.5% (20 digit*3)
(Accuracy in respect to maximum analog 25 5 (77 41)
output value) Ambient temperature Within 1.0% (40 digit*3)
0 to 55 (32 to 131)
Conversion speed 30 s (data refreshed every operation cycle)
Insulation method Inside the PLC and the analog output circuit are not insulated.
Occupied points 0 points (does not pertain to the max. No. of input/output points of the PLC.)
*1 There is a dead band near 0 V output, which is an area where some analog output values do not reflect digital input values.
*2 External load resistance is set to 2 k when shipped from the factory. Thus, output voltage will increase somewhat if the resistance is
set higher than 2 k. When the resistance is 1 M, output voltage increases maximum 2%.
*3 "Digit" refers to digital values.
2 SPECIFICATIONS
2.7 Built-in Analog Specifications 25
2.8 Communication Specifications

The built-in Ethernet and built-in RS-485 communication specifications are as explained below.
Built-in Ethernet communication

For details of built-in Ethernet communication, refer to the following.
MELSEC iQ-F FX5 User's Manual (Ethernet Communication)
MELSEC iQ-F FX5 User's Manual (SLMP)
Item Specifications
Data transmission speed 100/10 Mbps
Communication mode Full-duplex (FDX) / Half-duplex (HDX)
Interface RJ45 connector
Transmission method Base band
Maximum segment length (The distance between hub and node) 100 m (328'1")
Cascade connection 100BASE-TX Cascade connection max. 2 stages*1
10BASE-T Cascade connection max. 4 stages*1
Protocol type MELSOFT connection
SLMP (3E frame)
Socket communication
Predefined protocol support
Number of simultaneously open connections allowed Total of 8 for socket communication, MELSOFT connection, SLMP, and Predefined
protocol support
(Up to 8 external devices can access one CPU module at the same time.)
Insulation method Pulse transformer insulation
Cable used*2 For 100BASE-TX connection Ethernet standard-compatible cable, category 5 or higher (STP cable)
For 10BASE-T connection Ethernet standard-compatible cable, category 3 or higher (STP cable)
*1 Number of stages that can be connected when a repeater hub is used. When a switching hub is used, check the specifications of the
switching hub used.
*2 A straight cable can be used. If a personal computer or GOT and CPU module are directly connected a cross cable can be used.
Built-in RS-485 communication

For details of built-in RS-485 communication, refer to the following.
MELSEC iQ-F FX5 User's Manual (Serial Communication)
MELSEC iQ-F FX5 User's Manual (MODBUS Communication)
Item Specifications
Transmission standards Conforms to RS-485/RS-422 specifications
Data transmission speed Max. 115.2 kbps
Communication method Full-duplex (FDX) / Half-duplex (HDX)
Maximum total extension distance 50 m (164'0")
Protocol type MELSOFT connection
Non-protocol communication
MELSEC Communication protocol (3C/4C frames)
MODBUS RTU
Predefined protocol support
Inverter communication
N:N network
Insulation method Not insulated
Terminal resistors Built-in (OPEN/110 /330 )
2 SPECIFICATIONS
26 2.8 Communication Specifications
2.9 External Dimensions

CPU module
FX5U-32M
2
2-4.5 mounting holes Unit: mm (inches)
(mounting hole pitch)
90 (3.55")
80 (3.15")
22 W1 8 (0.32")
(0.87") W 83 (3.27")
Model W W1 (mounting hole pitch) Mass (weight)

FX5U-32M 150 mm (5.91") 123 mm (4.85") Approx. 0.65 kg (1.43 lbs)
• Exterior color
Main body: Munsell 0.6B7.6/0.2
• Accessories
Dust proof protection sheet
Manual supplied with product
FX5U-64M, FX5U-80M
4-4.5 mounting holes Unit: mm (inches)
90 (3.55")
80 (3.15")
22 W1 8 (0.32")
(0.87") W 83 (3.27")
Model W W1 (mounting hole pitch) Mass (weight)

• Exterior color
Main body: Munsell 0.6B7.6/0.2
• Accessories
Dust proof protection sheet
Manual supplied with product
2 SPECIFICATIONS
2.9 External Dimensions 27
2.10 Terminal Layout
Built-in RS-485 terminal

European type
terminal block
5 poles
SG (GND)
SDB (TXD-)
SDA (TXD+)
RDB (RXD-)
RDA (RXD+)
Built-in analog terminal

European type
terminal block
5 poles
V1+
V2+
V-
V+
V-
Analog Analog
input output
Built-in Ethernet connector

Pin Signal name
1 TD+
2 TD-
8 1 3 RD+
4 Not used
5 Not used
6 RD-
7 Not used
8 Not used
2 SPECIFICATIONS
28 2.10 Terminal Layout
Power, input/output terminal block

■Interpretation of terminal block layout
Power supply 24 V DC service
terminals power supply Input terminal [•] Vacant terminal (Do not use)
S/S 0 V X0 2 4 6 X10 12 14 16
2
L N 24 V 1 3 5 7 11 13 15 17
Output terminals
FX5U-32MR/ES connected to COM3
Y0 2 Y4 6 Y10 12 Y14 16
COM0 1 3 COM1 5 7 COM2 11 13 COM3 15 17
Common terminal Output terminal Partition

(4 points/common)
• Indication of power supply terminals

[L] and [N] terminals.
For external wiring, refer to Page 79 Power Supply Wiring.
• Indication of 24 V DC service power supply
[0V] and [24V] terminals.
• Indication of input terminal
For external wiring, refer to Page 83 Input Wiring.
• Indication of output terminals connected to common (COM)
One common terminal covers 4 or 8 output points.
The output number (Y) connected to common is the range inside the thick "separation line."
For transistor output (source) type, the "COM" terminal is the "+V" terminal.
■ FX5U-32M
S/S 0V X0 2 4 6 X10 12 14 16
L N 24V 1 3 5 7 11 13 15 17
FX5U-32MR/ES, FX5U-32MT/ES
Y0 2 Y4 6 Y10 12 Y14 16
COM0 1 3 COM1 5 7 COM2 11 13 COM3 15 17
FX5U-32MT/ESS
Y0 2 Y4 6 Y10 12 Y14 16
+V0 1 3 +V1 5 7 +V2 11 13 +V3 15 17
■FX5U-64M
S/S 0V 0V X0 2 4 6 X10 12 14 16 X20 22 24 26 X30 32 34 36
L N 24V 24V 1 3 5 7 11 13 15 17 21 23 25 27 31 33 35 37
Y0 2 Y4 6 Y10 12 Y14 16 Y20 22 24 26 Y30 32 34 36 COM5

COM0 1 3 COM1 5 7 COM2 11 13 COM3 15 17 COM4 21 23 25 27 31 33 35 37
FX5U-64MT/ESS
Y0 2 Y4 6 Y10 12 Y14 16 Y20 22 24 26 Y30 32 34 36 +V5

+V0 1 3 +V1 5 7 +V2 11 13 +V3 15 17 +V4 21 23 25 27 31 33 35 37
2 SPECIFICATIONS
2.10 Terminal Layout 29
■FX5U-80M
S/S 0V 0V X0 2 4 6 X10 12 14 16 X20 22 24 26 X30 32 34 36 X40 42 44 46
L N 24V 24V 1 3 5 7 11 13 15 17 21 23 25 27 31 33 35 37 41 43 45 47
Y0 2 Y4 6 Y10 12 Y14 16 Y20 22 24 26 Y30 32 34 36 Y40 42 44 46

COM0 1 3 COM1 5 7 COM2 11 13 COM3 15 17 COM4 21 23 25 27 COM5 31 33 35 37 COM6 41 43 45 47
FX5U-80MT/ESS
Y0 2 Y4 6 Y10 12 Y14 16 Y20 22 24 26 Y30 32 34 36 Y40 42 44 46

+V0 1 3 +V1 5 7 +V2 11 13 +V3 15 17 +V4 21 23 25 27 +V5 31 33 35 37 +V6 41 43 45 47
2 SPECIFICATIONS
30 2.10 Terminal Layout
3 PRODUCT LIST
The following shows the system configuration equipment of the FX5U.
3.1 Overall Configuration

Expansion boards
• FX5-232-BD
Battery
FX3U-32BL
3
• FX5-485-BD
• FX5-422-BD-GOT
Expansion CPU module I/O module Bus FX3 Intelligent function module
adapters conversion
Input/output Input Output Analog Network
Analog module
• FX5U-32MR/ES • FX5-8EX/ES • FX5-8EYR/ES • FX3U-4AD • FX3U-16CCL-M
• FX5-4AD-ADP • FX5U-32MT/ES • FX5-16EX/ES • FX5-8EYT/ES FX5-CNV-BUS • FX3U-4DA • FX3U-64CCL
• FX5-4DA-ADP • FX5-8EYT/ESS • FX3U-4LC
• FX5U-32MT/ESS Powered • FX3U-128ASL-M
• FX5-16EYR/ES Positioning
Communication • FX5U-64MR/ES input/output module • FX5-16EYT/ES
• FX5U-64MT/ES • FX5-32ER/ES • FX5-16EYT/ESS FX3U-1PG
• FX5-232ADP
• FX5U-64MT/ESS • FX5-32ET/ES High-speed counters
• FX5-485ADP
• FX5U-80MR/ES • FX5-32ET/ESS FX3U-2HC
• FX5U-80MT/ES
Intelligent function module FX3 extension power supply module
• FX5U-80MT/ESS
FX5-40SSC-S FX3U-1PSU-5V
FX5 extension power supply module

FX5-1PSU-5V Remote I/O
3 PRODUCT LIST
3.1 Overall Configuration 31
3.2 CPU Module

The CPU module incorporates a CPU, memory, input/output terminals, and power supply.
FX5U M
Power supply, Input/output type: Connection on terminal block.
• R/ES: AC power supply/24 V DC (sink/source) input/Relay output
Total number of CPU module • T/ES: AC power supply/24 V DC (sink/source) input/Transistor (sink) output
input/output points • T/ESS: AC power supply/24 V DC (sink/source) input/Transistor (source) output
AC power supply common to 24 V DC sink and source input

Model No. of input/output points Input type Output type Connection Power supply capacity
Total No. No. of No. of type 5 V DC power 24 V DC
of points input output supply service
points points power supply
FX5U-32MR/ES 32 points 16 points 16 points 24 V DC Relay Terminal block 900 mA 400 mA
(Sink/source) (480 mA*1)
FX5U-32MT/ES Transistor
(sink)
FX5U-32MT/ESS Transistor
(source)
FX5U-64MT/ES (Sink/source) Transistor (740 mA*1)
(sink)
(source)
FX5U-80MT/ES (Sink/source) Transistor (770 mA*1)
(sink)
(source)
*1 Power supply capacity when external power supply is used for input circuit
The model name of the CPU module can be checked on the nameplate on the right side. However, when
extension modules are connected, the nameplate cannot be seen. Check the model name in the following
places.
Model name
(abbreviation)
3 PRODUCT LIST
32 3.2 CPU Module
3.3 I/O Module

The I/O module is used to expand inputs/outputs.
For details, refer to Page 132 I/O Module.
FX5 E
Input/output type
• X/ES: 24 V DC (sink/source) input
• YR/ES: Relay output 3
• YT/ES: Transistor (sink) output
Input/output extension • YT/ESS: Transistor (source) output
Total number of
• R/ES: 24 V DC (sink/source) input/relay output
input/output points
• T/ES: 24 V DC (sink/source) input/transistor (sink) output
• T/ESS: 24 V DC (sink/source) input/transistor (source) output
Input module
The input module is used to expand inputs.
Model No. of input/output points Input type Output Connection Current consumption
Total No. No. of No. of type type 5 V DC power 24 V DC
of points input output supply power supply
points points
FX5-8EX/ES 8 points 8 points  24 V DC  Terminal block 75 mA 50 mA
(Sink/source)
FX5-16EX/ES 16 points 16 points 100 mA 85 mA
Output module
The output module is used to expand outputs.
Model No. of input/output points Input type Output Connection Current consumption
of points input output supply power supply
points points
FX5-8EYR/ES 8 points  8 points  Relay Terminal block 75 mA 75 mA
FX5-8EYT/ES Transistor
(sink)
FX5-8EYT/ESS Transistor
(source)
FX5-16EYR/ES 16 points  16 points  Relay Terminal block 100 mA 125 mA
FX5-16EYT/ES Transistor
(sink)
FX5-16EYT/ESS Transistor
(source)
Powered input/output module

The powered input/output module includes a power supply and is used to expand input/output.
Model No. of input/output points Input type Output Connection Power supply capacity
of points input output supply service power
points points supply
FX5-32ER/ES 32 points 16 points 16 points 24 V DC Relay Terminal block 965 mA 250 mA
(Sink/source) (310 mA*1)
FX5-32ET/ES Transistor
(sink)
FX5-32ET/ESS Transistor
(source)
*1 Power supply capacity when external power supply is used for input circuit
3 PRODUCT LIST
3.3 I/O Module 33
3.4 Intelligent Function Module

Intelligent function modules are modules that have functions other than input/output, such as simple motion modules.
For details, refer to manuals of each module.
FX5 intelligent Function Module
Positioning
Model Function No. of occupied Current consumption
input/output 5 V DC power 24 V DC External 24 V DC
points supply power supply power supply
FX5-40SSC-S 4-axis control (compatible with SSCNET /H) 8 points   250 mA
FX3 intelligent Function Module

The following FX3 intelligent functions modules can be used in FX5U CPU module systems by using bus conversion modules.
For the bus conversion modules to be connected, refer to Page 36 Bus Conversion Module.
To use the modules, refer to Page 40 Bus conversion module.
Analog
FX3U-4AD 4-ch voltage/current input 8 points 110 mA  90 mA
FX3U-4DA 4-ch voltage/current output 120 mA  160 mA
FX3U-4LC 4-ch temperature control (resistance 160 mA  50 mA
thermometer/thermocouple/low voltage)
4 transistor output points
Positioning
FX3U-1PG Pulse output for independent 1-axis control 8 points 150 mA  40 mA
High-speed counter
input/output 5 V DC power supply 24 V DC power supply
points
FX3U-2HC 2-ch high-speed counter 8 points 245 mA 
3 PRODUCT LIST
34 3.4 Intelligent Function Module
Network
FX3U-16CCL-M*1 Master for CC-Link (compatible with Ver. 2.00 8 points*2   240 mA
and Ver. 1.10)
FX3U-64CCL*1 Intelligent device station for CC-Link 8 points   220 mA
FX3U-128ASL-M*1*5 Master for AnyWireASLINK 8 points*3 130 mA  100 mA*4
*1 GX Works3 does not support this module. When using this module, perform setting via buffer memory.
3
*2 Number of remote I/O points is added.
For details, refer to Page 46 Calculation of number of remote I/O points.
*3 The number of input/output points set by the rotary switch is added. For details, refer to FX3U-128ASL-M User's Manual.
*4 This value does not include supply current to slave modules. For details, refer to FX3U-128ASL-M User's Manual.
*5 Note that the warranty for this model differs from the ones for other PLCs. For details, refer to FX3U-128ASL-M User's Manual.
3.5 Expansion Board

The expansion board is to expand functions and is connected to the front face of the CPU module.
For details on the specifications of the expansion board, refer to Hardware manuals of each product.
input/output points 5 V DC power supply 24 V DC power supply
FX5-232-BD For RS-232C communication  20 mA 
FX5-485-BD For RS-485 communication  20 mA 
FX5-422-BD-GOT For RS-422 communication (For  20 mA*1 
GOT connection)
*1 When the GOT 5 V type is connected with this product, the current consumption increases.
For the current consumption, refer to the manual of the model to be connected.
3.6 Expansion Adapter

The expansion adapter is to expand functions and is connected on the left side of the CPU module.
For details on the specifications of the expansion adapter, refer to Hardware manuals of each product.
input/output points 5 V DC power 24 V DC power External 24 V DC
supply supply power supply
FX5-4AD-ADP 4-ch voltage input/current input  10 mA 20 mA 
FX5-4DA-ADP 4-ch voltage output/current output  10 mA  160 mA
FX5-232ADP For RS-232C communication  30 mA 30 mA 
FX5-485ADP For RS-485 communication  20 mA 30 mA 
3 PRODUCT LIST
3.5 Expansion Board 35
3.7 Extension Power Supply Module

The extension power supply module is an added power supply if the built-in power supply of the CPU module is insufficient.
For details on the specifications of the extension power supply module, refer to Manuals of each product.
FX5 expansion power supply module

Model Function No. of occupied Power supply capacity
*1
FX5-1PSU-5V Extension power supply  1200 mA 300 mA*1
FX3 expansion power supply module

With FX5U systems, the following FX3 extension power supply module can be used.
However, a bus conversion module is required to use the intelligent function modules.
For details, refer to Page 40 Bus conversion module.
Model Function No. of occupied Power supply capacity
FX3U-1PSU-5V Extension power supply  1000 mA*1 300 mA*1
*1 If the ambient temperature exceeds 40, use the extension power supply module at the following current values within the derating
range.
Derating curve
FX5-1PSU-5V FX3U-1PSU-5V
Output current [mA] Output current [mA]
5 V DC
1200
5 V DC
1000
800 800
24 V DC 24 V DC
300 300
200 Ambient 200 Ambient
temperature [] temperature []
40 55 40 55
3.8 Bus Conversion Module

The bus conversion module is to connect FX3 extension modules with FX5U CPU module systems. For details on the
specifications of the bus conversion module, refer to MELSEC iQ-F FX5-CNV-BUS Hardware Manual.
FX5-CNV-BUS Bus conversion from FX5 8 points 150 mA 
extension modules or FX5
intelligent function modules
3.9 SD Memory Card

For details on the SD memory card, refer to Page 141 SD Memory Card.
Model Function
NZ1MEM-2GBSD SD memory card (Mitsubishi product)
NZ1MEM-4GBSD
L1MEM-2GBSD
L1MEM-4GBSD
3 PRODUCT LIST
36 3.7 Extension Power Supply Module
3.10 Battery
For details on the battery, refer to Page 116 Battery.
Model Function
FX3U-32BL Battery
3.11 Communication Cable

3
Use a communication cable to connect a PLC with a personal computer by RS-232C communication.
Model Function
FX-232CAB-1 FX5-232ADPPersonal computer
FX5-232-BDPersonal computer
3.12 Engineering Tool

For design and programming of FX5U CPU module systems, use GX Works3.
For the operation method, refer to GX Works3 Operating Manual.
Model Function
GX Works3 MELSEC PLC software package
3 PRODUCT LIST
3.10 Battery 37
4 SYSTEM CONFIGURATION
Configuration of a whole system

The configuration of an entire system is shown below as an example.
For assignment of the module numbers for extension modules, refer to Page 62 Module number of Extension modules.
Ex.
Configuration of whole system
Expansion board and expansion adapters FX5 extension module

Expansion board FX5 extension power
CPU module I/O module supply module Intelligent module
Output Input Simple motion
module module module
FX5U-32MR/ES FX5-16EYR/ES FX5-16EX/ES FX5-1PSU-5V FX5-40SSC-S
Expansion X000 to X017 - X020 to X037 Module No.1
adapters
Y000 to Y017 Y020 to Y037 -
Range of devices powered

Range of devices powered by FX5 extension power
by CPU module supply module
Bus FX3 extension module

conversion
module
FX3 extension power supply module FX3 extension module
Intelligent Intelligent Intelligent
FX3U-1PSU-5V FX3U-4AD FX3U-4DA FX3U-16CCL-M
FX5-CNV-BUS Module No.3 Module No.4 Module No.5
Module No.2
Range of devices powered by FX3 extension power supply module
When CC-Link is used
Remote I/O Remote I/O
38
4.1 Rules of System Configuration

The system configuration must meet the following four requirements.
Number of connected extension device

The number of extension devices that can be connected to a single system of FX5U CPU module is limited.
For details, refer to Page 41 Limitations on the Number of Connected Extension Devices.
Ex.
Up to 16 modules*1
4
Expansion CPU module Input FX5 Input FX3
Expansion FX5 extension FX5 Bus extension FX3 FX3
adapters module, module,
adapters Expansion Intelligent power Intelligent conversion power Intelligent Intelligent
(Commu- board Output supply Output supply
(Analog) module module module module module
nication) module module module module
Up to 4 Up to 2 Up to 1 Up to 8 Up to 1 Up to 8 modules
modules modules module modules module
Up to 12 modules Up to 8 modules
Up to 10 modules
Up to 2 modules
*1 Extension power supply modules are not included in the number of connected devices.
Number of input/output points

With the FX5U CPU module, a total of 512 points or less including the number of input/output points of extension devices
(max. 256 points) and number of remote I/O points (max. 384 points) can be controlled.
For details on the number of input/output points, refer to Page 45 Limitation on the Number of Input/Output Points.
Number of input/output points on whole system Up to 512 points
1. Number of input/output points

(including input/output occupied points) Up to 256 points
FX5 FX5 Bus

• Expansion board • CC-Link master
CPU module I/O module Intelligent Intelligent conversion
• Expansion adapter • AnyWireASLINK master
2. Number of remote input/output points for

Up to 384 points
CC-Link/AnyWireASLINK
CC-Link/AnyWireASLINK system
Remote I/O station Remote I/O station Remote I/O station Remote I/O station
4.1 Rules of System Configuration 39
Current consumption
Power of extension devices is supplied from the CPU module or extension power supply module.
The number of extension devices that can be connected must be determined from the capacity of the power supply.
For details on the current consumption, refer to Page 48 Limitation on Current Consumption.
CPU module Input Powered Input FX5 Input

Expansion FX5 FX5 extension module, FX5 Bus FX3
module, input/ module,
Expansion Intelligent Intelligent power Intelligent conversion Intelligent
adapters Output output Output supply Output
board module module module module module
module module module module module
Power supply from CPU module*1 Power supply from Power supply from
powered input/output module*1 FX5 extension power supply module*1
*1 Power is supplied to input circuit of input modules by service power supply or external power supply.
Limitations when using FX3 extension devices

■Bus conversion module
• A bus conversion module is required to use FX3 extension module. FX3 extension module can be connected to the right
side of the bus conversion module only.
• For limitation on the number of connectable modules, refer to Page 44 Connection to the bus conversion module
(connection with FX3 extension devices).
■Limitations on intelligent function modules

Note that some FX3 intelligent function modules have limitations on the number of modules and order in which they are added
for each individual module.
Model Limitations
FX3U-2HC Up to two modules connectable per system.
When FX5-1PSU-5V is not used, connect immediately after the bus conversion module.
FX3U-16CCL-M Only one module may be connected per system.
FX3U-64CCL Only one module may be connected per system.
FX3U-128ASL-M Only one module may be connected per system.
40 4.1 Rules of System Configuration
4.2 Limitations on the Number of Connected

Extension Devices
Number of connected expansion boards
Only 1 expansion board can be connected on the front face of the CPU module.
Expansion board
Number of connected expansion adapters

There is a limitation on the number of expansion adapter connected to the CPU module as follows.
Type Limitations
Communication adapter Up to 2 modules can be connected.
Analog adapter Up to 4 modules can be connected.
Communication
Analog adapter
adapter
Up to 2 modules FX5-232ADP FX5-485ADP
Up to 4 modules FX5-4AD-ADP FX5-4DA-ADP
4.2 Limitations on the Number of Connected Extension Devices 41
Number of connected extension modules
Overall system limitation

There is a limitation on the number of connected extension modules in a whole system as follows.
Type Limitations
Extension module Up to 16 modules can be connected to a system.
(Extension power supply modules are excluded.)
Extension power supply module Up to 2 modules can be connected to a system.
Bus conversion module Only 1 module can be connected to a system.
Up to 16 modules (excluding extension power supply module)
Extension Extension
I/O I/O Bus
CPU module power power
•••• •••• conversion ••••
module supply module supply
module
module module
Up to 1 module
Up to 2 modules
Connection to the CPU module

There is a limitation on the number of extension modules connected to the CPU module as follows.
The number of extension modules added from the right side of the CPU module to powered input/output module or the
extension power supply module must be as follows.
Type Limitations
Total No. of input modules, output modules, intelligent function modules, and bus Up to 12 modules can be connected.
conversion modules
Total No. of intelligent function module and bus conversion modules Up to 8 modules can be connected.
Input Powered input/ Input

module, FX5 output module, module, FX5
CPU module Intelligent FX5 extension Intelligent
Output power supply Output
module module module module
module
Up to 8
modules
Up to 12 modules
Input FX3 extension

Bus FX3 FX3
CPU module module, Intelligent
conversion Intelligent power supply Intelligent
Output module
module
Up to 8 modules
Up to 12 modules
42 4.2 Limitations on the Number of Connected Extension Devices
Connection to the powered input/output module

There is a limitation on the number of extension modules connected to the powered input/output module as follows.
The number of connected modules from the right side of the powered input/output module the next extension power supply
module added later must be as follows.
Type Limitations
Total No. of input module, output module intelligent function modules, and bus Up to 10 modules can be connected.
conversion modules

Powered FX5 output module, FX5
module, module,
input/output
module
Output
module
Intelligent FX5 extension
module power supply Output
module
Intelligent
module 4
module
Up to 8
modules
Up to 10 modules
Input
Powered FX5 Bus FX3 FX3 extension FX3
module,
input/output Intelligent conversion Intelligent power supply Intelligent
Output
module module module module module module
module
Up to 8 modules
Up to 10 modules
Connection to the FX5 extension power supply module (FX5-1PSU-5V)

There is a limitation on the number of extension modules connected to the FX5 extension power supply module as follows.
The number of connected modules from the right side of the FX5 extension power supply module to powered input/output
module or the next extension power supply module added later must be as follows.
Type Limitations
Total No. of input modules, output modules, intelligent function modules, and bus Up to 10 modules can be connected.
conversion modules

FX5 extension FX5 output module, FX5
module, module,
power supply FX5 extension
Output Intelligent power supply Output Intelligent
module module
Up to 8
modules
Up to 10 modules
Input
FX5 extension FX5 Bus FX3 FX3 extension FX3
module,
power supply Intelligent conversion Intelligent power supply Intelligent
Output
module module module module module module
module
Up to 8 modules
Up to 10 modules
4.2 Limitations on the Number of Connected Extension Devices 43
Connection to the bus conversion module (connection with FX3 extension devices)
There is a limitation on the number of extension modules connected to the bus conversion module as follows.
The number of modules connected on the right side of the bus conversion module must be as follows.
■When using FX3 extension power supply modules

Type Limitations
Total No. of intelligent function modules Up to 8 modules can be connected.
FX3
Bus extension FX3
conversion power Intelligent •••••
module supply module
module
Up to 8 modules
■When not using FX3 extension power supply modules

Type Limitations
Total No. of intelligent function modules Up to 6 modules can be connected.
Bus FX3
conversion Intelligent • • • • •
module module
Up to 6 modules
Precautions
FX5 extension modules cannot be connected on the right side of the bus conversion module.
44 4.2 Limitations on the Number of Connected Extension Devices
4.3 Limitation on the Number of Input/Output Points

With the FX5U CPU module, a total of 512 points including the number of input/output points of extension devices (max. 256
points) and the number of remote I/O points (max. 384 points) can be controlled.
Number of input/output points on whole system Up to 512 points
1. Number of input/output points

(including input/output occupied points) Up to 256 points
FX5 FX5 Bus

• Expansion board • CC-Link master
CPU module I/O module Intelligent Intelligent conversion
• Expansion adapter • AnyWireASLINK master
4
2. Number of remote input/output points for
Up to 384 points
CC-Link/AnyWireASLINK
CC-Link/AnyWireASLINK system
Remote I/O station Remote I/O station Remote I/O station Remote I/O station
Total number of I/O points and remote I/O points

With the FX5U CPU module, a total of 512 points or less including the number of input/output points of extension devices and
number of remote I/O points can be controlled.
The total number of I/O points and remote I/O points must not exceed 512 points.
Number of input/output
Number of input/output points Number of remote I/O points
points on whole system
512 points (1) points (2) points

≥ +
Maximum number of The total number of inputs and The total number of remote I/O
points controllable on outputs which is obtained in the which is obtained in the next
system next subsection. subsection.
4.3 Limitation on the Number of Input/Output Points 45
Calculation of number of input/output points

The number of input/output points is the total of the number of input/output points of the CPU module and I/O module, and the
number of occupied input/output points of intelligent function modules.
The total number of input/output points must not exceed 256 points.
Maximum number of Number of Number of input/output points on Number of input/output

input/output points input/output points CPU module and I/O module occupied points
256 points (1) (A) + (B) (C) modules ×8 points

≥ = +
Intelligent function module,
Total number of input/output points of CPU bus conversion module
module and I/O modules occupies 8 input/output points.
(A): Number of input/output points of CPU module

(B): Number of input/output points of I/O modules
(C): Number of Intelligent function modules and bus conversion modules
Total number of input/output points of the CPU module and I/O modules
Count the total number of input/output points of the CPU module and I/O modules.
To obtain the total number of input/output points, count the input points (X000 and more) and output points (Y000 and more) of
the CPU module and I/O modules.
For details on the number of input/output points by model, refer to the following.
Page 32 CPU Module
Page 33 I/O Module
Number of occupied input/output points of intelligent function modules

Count the number of occupied input/output points of intelligent function modules.
The number of occupied input/output points per module is 8.
For details on the number of occupied input/output points by model, refer to Page 34 Intelligent Function Module.
Calculation of number of remote I/O points

If the master module of the network is used, calculate the number of remote I/O points connected on the network.
The total number of remote I/O points must not exceed 384 points.
Maximum number of The total number of remote I/O points

Remote I/O points
remote I/O points in CC-Link and AnyWireASLINK
384 points (2) (a) + (b) points

≥ =
The total number of the remote I/O (a): CC-Link remote I/O
points connected on the network (b): AnyWireASLINK remote I/O
The maximum number of remote I/O points differs according to type of the network.
Precautions
Precautions when using CC-Link master (FX3U-16CCL-M) and AnyWireASLINK master (FX3U-128ASL-M) together
When using FX3U-16CCL-M and FX3U-128ASL-M together, connect FX3U-128ASL-M on the left side. In the FX5U CPU
module, FX3U-16CCL-M parameters are set up by PLC program and will occupy up to 256 remote I/O points. Therefore, the
remote I/O points of FX3U-128ASL-M that is connected to the right side may be less than 128 points when FX3U-16CCL-M is
connected to the left side.
Ex.
When input/output points are 160 points and CC-Link master are 256 points: 512 points - 160 points - 256 points = 96 points
Remote I/O points of AnyWireASLINK master are 96 points or less.
46 4.3 Limitation on the Number of Input/Output Points
CC-Link remote I/O

Remote I/O points that are used in FX3U-16CCL-M are calculated as "number of stations X 32 points."
Even if using less than 32 remote I/O points, calculate as "number of stations X 32 points."
Maximum number of
Actually used CC-Link remote I/O points
CC-Link remote I/O points
256 points (a) × 32 points

station
≥ =
(a) CC-Link remote The total number of the remote I/O
I/O points stations × 32 points
In the FX5U CPU module, FX3U-16CCL-M parameters are set up by PLC program and will occupy up to 256 remote I/O
points. 4
When the total number of the number of input/output points (including occupied input/output points) and the number of remote
I/O points of FX3U-128ASL-M that is connected to the left side exceeds 256 points, the difference of 512 minus that total can
be used as CC-Link remote I/O points.
AnyWireASLINK remote I/O

The number of input/output points set by the rotary switch of the AnyWireASLINK master is assigned as remote I/O of
AnyWireASLINK.
Use the number of input/output points set by the rotary switch of the AnyWireASLINK master as the number of remote I/O
points.
For details, refer to FX3U-128ASL-M User's Manual.
Maximum number of
AnyWireASLINK remote AnyWireASLINK remote I/O
I/O points
128 points (b) points

≥
(b) Number of remote I/O points assigned to
AnyWireASLINK master
4.3 Limitation on the Number of Input/Output Points 47
4.4 Limitation on Current Consumption

Power required for expansion adapters, expansion boards, and extension modules is supplied from the CPU module or
extension power supply module. The number of extension devices that can be connected must be determined from the
capacity of the power supply.
Power supply check from the CPU module (current consumption

calculation)
Check if power can be supplied to extension devices with the power supply capacity of the CPU module.
Ex. CPU module

FX5 Bus FX3
Expansion Expansion Output Input
Intelligent conversion Intelligent
adapters board module module
Power supply from CPU module

Calculate following the procedure below.
1. Check the power supply capacity of the CPU module used. (Page 32 CPU Module)
Ex.
Type Model Power supply capacity

5 V DC power supply 24 V DC service power supply
CPU module FX5U-32MT/ES 900 mA 400 mA*1
*1 Value when service power supply is used for input circuits. The power supply capacity differs when external power supply is used for
input circuit.
2. Check the current consumption of extension devices.
(Page 33 I/O Module), (Page 34 Intelligent Function Module)
Ex.
Type Model Current consumption

5 V DC power supply 24 V DC power supply
Expansion board FX5-232-BD 20 mA 
Expansion adapter FX5-232ADP 30 mA 30 mA
Output module FX5-16EYT/ES 100 mA 125 mA
Input module FX5-16EX/ES 100 mA 85 mA*1
Simple motion module FX5-40SSC-S  
Bus conversion module FX5-CNV-BUS 150 mA 
Analog input FX3U-4AD 110 mA 
*1 If using external power supply for input circuit, calculate current consumption of 24 V DC power supply as 0 mA.
3. Calculate the total current consumption of each power supply.
Ex.
Power supply type Total current consumption

5 V DC power supply 510 mA
48 4.4 Limitation on Current Consumption
4. Check if expansion to the CPU module is permitted.

• 5 V DC power supply
Capacity of 5 V DC
Current consumption Calculation result
power supply
CPU module Total of current

consumed by extension
module
mA - mA = mA ≥ 0 mA
Ex. 900 mA 510 mA 390 mA
4
The value obtained by this calculation (when the value is positive) indicates the remaining capacity of 24 V DC service power
supply, and the capacity can be used for external loads.
Capacity of 24 V DC Current consumption Calculation result

power supply
Total of current
CPU module consumed by extension
module
Ex. 400 mA 240 mA 160 mA
If the calculation result is a negative value, the current consumption exceeds the power supply capacity of the CPU module.
Reconfigure the system, adding powered input/output module or extension power supply modules.
Power supply check from the powered input/output module

(current consumption calculation)
If 24 V DC and 5 V DC power supplies of the CPU module are insufficient and system cannot be extended, add a powered
input/output module.
Check if power can be supplied to extension modules with the power supply capacity of the powered input/output module.
CPU module Powered

Expansion Input Output FX5 Bus FX3
Expansion input/ Input Output
adapters module module Intelligent conversion Intelligent
board output module module
module
Power supply from powered input/output module

1. Check the power supply capacity of the powered input/output module.

(Page 33 Powered input/output module)
Ex.

Powered input/output module FX5-32ER/ES 965 mA 250 mA*1
*1 Value when service power supply is used for input circuits.The power supply capacity differs when external power supply is used for
input circuit.
4.4 Limitation on Current Consumption 49
2. Check the number of input/output points and current consumption of the extension module.
(Page 33 I/O Module)
(Page 34 Intelligent Function Module)
Ex.

Input module FX5-16EX/ES 100 mA 85 mA
Output module FX5-16EYR/ES 100 mA 125 mA
Simple motion modules FX5-40SSC-S  
Ex.

4. Check if expansion to the extension power supply module is permitted.

Capacity of 5 V DC
power supply
Powered input/output Total of current

module consumed by extension
module
Ex. 965 mA 460 mA 505 mA
The value obtained by this calculation (when the value is positive) indicates the remaining capacity of 24 V DC service power
supply, and the capacity can be used for external loads.
Capacity of 24 V DC Current consumption Calculation result

service power supply
Total of current
Powered input/output consumed by extension
module module
Ex. 250 mA 210 mA 40 mA
Power supply check from extension power supply module

(current consumption calculation)
If 5 V DC power supply of the CPU module is insufficient and cannot be extended, add an extension power supply module.
Check if power can be supplied to extension modules with the power supply capacity of the extension power supply module.
Ex.
CPU module FX5

extension Input FX5 Bus FX3
Expansion Expansion Output Output
power Intelligent conversion Intelligent
adapters board module supply module module
module
Power supply from FX5 extension power supply module

4
(Only the 5 V DC power supply for the input module is
supplied by the extension power supply module.)
1. Check the power supply capacity of the extension power supply module used.
(Page 36 Extension Power Supply Module)
Ex.

FX5 extension power supply module FX5-1PSU-5V 1200 mA 300 mA
If the ambient temperature exceeds 40, use the extension power supply module at the following current
values within the derating range.
Derating curve
FX5-1PSU-5V
Output current [mA]
5 V DC
1200
800
24 V DC
300
200 Ambient
temperature []
40 55
2. Check the number of input/output points and current consumption of the extension module.
(Page 33 I/O Module)
(Page 34 Intelligent Function Module)
Ex.

Input module FX5-16EX/ES 100 mA *1
*1 24 V DC power supply is supplied from the CPU module or powered input/output module.
4.4 Limitation on Current Consumption 51
When connecting an input module after (on the right side of) the extension power supply module
When using service power supply of the CPU module or powered input/output module for input circuit of an
input module, include the input module in the 24 V DC current consumption calculation.
5 V DC power supply of the input module is supplied from the extension power supply module.
CPU module, Extension

Powered FX5 power FX5
Input Input
input/output Intelligent supply Intelligent
module module
Power supply from CPU module or When the CPU module or powered input/output module
powered input/output module supplies the 24 V DC power supply for the input circuit, current
consumption of 24 V DC should be included in the supply
range from the CPU module or powered input/output module.
Ex.

4. Check if expansion to the extension power supply module is permitted.

Capacity of 5 V DC
power supply
Extension power Total of current
supply module consumed by extension
module
Ex. 1200 mA 460 mA 740 mA
Capacity of 24 V DC
power supply
module
Ex. 300 mA 125 mA 175 mA
If the calculation result is a negative value, the current consumption exceeds the power supply capacity of the extension
power supply module.
Reconfigure the system, adding powered input/output module or extension power supply modules.
4.5 Rules of System Configuration and Examples of

Reconfiguration
The rules of system configuration are explained below referring to a sample system configuration using an expansion board,
expansion adapter, I/O module, and intelligent function module.
System configuration example

The following system configuration is under consideration.
FX3U-64CCL
FX5-485ADP
FX5-232ADP
FX5-16EX/ES
FX5-16EYT/ES
FX5-16EYT/ES
FX5-16EYR/ES
FX5-40SSC-S
FX5-CNV-BUS
FX3U-1PG
FX3U-4AD
FX3U-4LC
FX3U-128ASL-M
FX5U-32MR/ES
4
CC-Link To CC-Link
FX5-232-BD master station
The number of transmission points

setting for AnyWireASLINK
64 points
Remote I/O Remote I/O Remote I/O

station station station
Check of limitation on the number of modules

Check if the sample system configuration is within the connectable-module range.
■Number of connected expansion boards

(Page 41 Number of connected expansion boards)
Type No. of modules used Limitations Judgment
Expansion board 1 Only 1 OK
■Number of connected expansion adapters

(Page 41 Number of connected expansion adapters)
Expansion adapter (Communication) 2 Up to 2 OK
■Number of connected extension modules

• Number of modules connected on whole system
(Page 42 Overall system limitation)
Extension module 11 Up to 16 OK
Extension power supply module Not used Up to 2 OK
Bus conversion module 1 Only 1 OK
4.5 Rules of System Configuration and Examples of Reconfiguration 53
• Number of modules connected to the CPU module

(Page 42 Connection to the CPU module)
Total No. of I/O modules, intelligent function modules, and bus conversion modules 11 Up to 12 OK
Total No. of intelligent function module and bus conversion modules 7 Up to 8 OK
• Number of modules connected to the bus conversion module

(Page 44 Connection to the bus conversion module (connection with FX3 extension devices))
Total No. of intelligent function modules 5 Up to 6 OK
(When not using extension power supply modules)
Check on limitations when using FX3 extension devices

Check the use of the FX3 extension devices.
■Use of the bus conversion module

(Page 40 Bus conversion module)
Limitations Judgment
FX3 extension modules are connected on the right side of the bus conversion module. OK
FX5 extension modules are connected on the left side of the bus conversion module. OK
■Connection of intelligent function modules

(Page 40 Limitations on intelligent function modules)
Model Limitations Judgment
FX3U-128ASL-M Only one module may be connected to the system. OK
FX3U-64CCL Only one module may be connected to the system. OK
54 4.5 Rules of System Configuration and Examples of Reconfiguration
Check of limitation on the number of input/output points

Check if the number of input/output points of the sample system configuration is within the limit range.
■Number of input/output points

(Page 46 Calculation of number of input/output points)
Type Model No. of input/output No. of occupied input/
points output points
CPU module FX5-32MR/ES 32 points 
Expansion board FX5-232-BD  
Expansion adapter FX5-232ADP  
Expansion adapter FX5-485ADP  
Input module FX5-16EX/ES 16 points 
4
Output module FX5-16EYT/ES 16 points 
Output module FX5-16EYR/ES 16 points 
Simple motion module FX5-40SSC-S  8 points
Bus conversion module FX5-CNV-BUS  8 points
Pulse output module FX3U-1PG  8 points
Analog input module FX3U-4AD  8 points
Temperature controller module FX3U-4LC  8 points
AnyWireASLINK master module FX3U-128ASL-M  8 points
CC-Link intelligent device module FX3U-64CCL  8 points
Number of Number of occupied Calculation result Max. number of

input/output points input/output points input/output points
96 points + 56 points = 152 points ≤ 256 points OK

■Number of remote I/O points
(Page 46 Calculation of number of remote I/O points)
Network No. of remote I/O points
AnyWireASLINK 64 points
Maximum number of
Remote I/O points
Remote I/O points
64 points ≤ 384 points OK

■Total number of I/O points and remote I/O points
(Page 45 Limitation on the Number of Input/Output Points)
Calculation Max. number of

Total number of input/output points
result input/output points
Number of input/output points Remote I/O points
Check of limitation on current consumption

Check if power required for extension devices can be supplied from the CPU module and extension power supply module.
A case using service power supply for input circuit is explained as an example.
■ Check of power supply from the CPU module

(Page 48 Power supply check from the CPU module (current consumption calculation))
• Power supply capacity of the CPU module
CPU module FX5U-32MR/ES 900 mA 400 mA
(Service power supply is used for input circuit)
• Current consumption of extension devices

Pulse output module FX3U-1PG 150 mA 
Analog input module FX3U-4AD 110 mA 
Temperature controller module FX3U-4LC 160 mA 
AnyWireASLINK master module FX3U-128ASL-M 130 mA 
CC-Link intelligent device module FX3U-64CCL  
Capacity of 5 V DC
power supply
module
900 mA - 1170 mA = -270 mA NG

Capacity of 24 V
DC power supply

module
400 mA - 520 mA = -120 mA NG
Result check
Because calculation results for 5 V DC or 24 V DC current consumption are negative, reconfiguration is necessary.
The judgment procedure after reconfiguration is explained on the following pages.
System reconfiguration example

If current consumption of the 5 V DC or 24 V DC power supply is insufficient with the CPU module only, powered input/output
module or use an extension power supply module.
Reconfigure the example system configuration using an extension power supply module.
F3U-64CCL
FX5-485ADP
FX5-232ADP
FX5-16EX/ES
FX5-16EYT/ES
FX5-16EYT/ES
FX5-1PSU-5V
FX5-16EYR/ES
FX5-40SSC-S
FX5-CNV-BUS
FX3U-1PG
FX3U-4AD
FX3U-4LC
FX3U-128ASL-M
FX5U-32MR/ES
To CC-Link
CC-Link
master
FX5-232-BD station
The number of transmission points

4
setting for AnyWireASLINK
64 points
Remote Remote Remote

I/O station I/O station I/O station
Check of limitation on the number of modules

Check if the example system configuration is within the connectable-module range.
■Number of connected expansion boards

(Page 41 Number of connected expansion boards)
Expansion board 1 Only 1 OK
■Number of connected expansion adapters

(Page 41 Number of connected expansion adapters)
Expansion adapter (Communication) 2 Up to 2 OK
■Number of connected extension modules

• Number of modules connected on whole system
(Page 42 Overall system limitation)
Extension module 11 Up to 16 OK
Extension power supply module 1 Up to 2 OK
Bus conversion module 1 Only 1 OK
• Number of modules connected to the CPU module

(Page 42 Connection to the CPU module)
• Number of modules connected to extension power supply module

(Page 43 Connection to the FX5 extension power supply module (FX5-1PSU-5V))
• Number of modules connected to the bus conversion module

(Page 44 Connection to the bus conversion module (connection with FX3 extension devices))
Total No. of intelligent function modules 5 Up to 6 OK
(When not using extension power supply modules)
Check on limitations when using FX3 extension devices

Check on limitations when using the FX3 extension devices.
■Use of the bus conversion module

(Page 40 Bus conversion module)
Limitations Judgment
FX3 extension modules are connected on the right side of the bus conversion module. OK
FX5 extension modules are connected on the left side of the bus conversion module. OK
■Connection of intelligent function modules

(Page 40 Limitations on intelligent function modules)
Model Limitations Judgment
FX3U-128ASL-M Only one module may be connected to the system. OK
FX3U-64CCL Only one module may be connected to the system. OK
Check of limitation on the number of input/output points

Check if the number of input/output points of the sample system configuration is within the limit range.
■Number of input/output points

(Page 46 Calculation of number of input/output points)
Type Model No. of input/output No. of occupied input/
points output points
CPU module FX5-32MR/ES 32 points
Input module FX5-16EX/ES 16 points 
FX5 extension power supply module FX5-1PSU-5V  
Output module FX5-16EYR/ES 16 points 
Simple motion module FX5-40SSC-S  8 points
Bus conversion module FX5-CNV-BUS  8 points
Pulse output module FX3U-1PG  8 points
Analog input module FX3U-4AD  8 points
Temperature controller module FX3U-4LC  8 points
AnyWireASLINK master module FX3U-128ASL-M  8 points
CC-Link intelligent device module FX3U-64CCL  8 points
Number of input/output Number of occupied Max. number of

Calculation result
points input/output points input/output points
■Number of remote I/O points

(Page 46 Calculation of number of remote I/O points)
Network No. of remote I/O points
AnyWireASLINK 64 points
Maximum number of
Remote I/O points
Remote I/O points
64 points ≤ 384 points OK

■Total number of I/O points and remote I/O points
(Page 45 Limitation on the Number of Input/Output Points)
4
Max. number of
Total number of input/output points Calculation result
input/output points
Number of input/output points Remote I/O points
Check of limitation on current consumption

Check if power required for extension devices can be supplied from the CPU module and extension power supply module.
A case using service power supply for input circuit is explained as an example.
■ Check of power supply from the CPU module

(Page 48 Power supply check from the CPU module (current consumption calculation))
Power supply capacity of the CPU module
CPU module FX5U-32MR/ES 900 mA 400 mA
(Service power supply is used for input circuit)
Current consumption of extension devices

Capacity of 5 V DC
power supply

module
900 mA - 370 mA = 530 mA OK

Capacity of 24 V DC
service power supply
module
400 mA - 395 mA = 5 mA OK
■ Check of power supply from the extension power supply module

(Page 51 Power supply check from extension power supply module (current consumption calculation))
Power supply capacity of the extension power supply module
FX5 extension power supply module FX5-1PSU-5V 1200 mA 300 mA
Current consumption of extension devices

Simple motion module
Bus conversion module
FX5-40SSC-S
FX5-CNV-BUS

150 mA


4
Pulse output module FX3U-1PG 150 mA 
Analog input module FX3U-4AD 110 mA 
Temperature controller module FX3U-4LC 160 mA 
AnyWireASLINK master module FX3U-128ASL-M 130 mA 
CC-Link intelligent device module FX3U-64CCL  
Capacity of 5 V DC
power supply
module
1200 mA - 800 mA = 400 mA OK

Capacity of 24 V DC
power supply
module
300 mA - 125 mA = 175 mA OK
Result check
The reconfigured system is acceptable because the number of extension devices, consumption capacity of 5 V DC and 24 V
DC power supply, and number of input/output points are all within the limit range.
4.6 Numbers and Assignment in System

Input/output numbers and module numbers in an FX5U CPU module system are explained.
Module input/output number

The input/output numbers are octal numbers. Input is assigned to "X" and output to "Y."
Input/output numbers are used for communication of ON/OFF data between I/O modules and the CPU module.
• Input/output numbers (X/Y) are octal.
Input/output numbers (X/Y) are automatically assigned as shown below.
X000 to X007, X010 to X017, X020 to X027, ... X070 to X077, X100 to X107, ...
Y000 to Y007, Y010 to Y017, Y020 to Y027, ... Y070 to Y077, Y100 to Y107, ...
• Numbers for added I/O module
To an added I/O module, input numbers and output numbers following the input numbers and output numbers given to the
preceding device are assigned. The last digit of the assigned numbers must begin with 0.
Module number of Extension modules

The CPU module automatically assigns numbers (1 to 16) to intelligent function modules or bus conversion module as module
numbers in order of distance from the CPU module.
• Intelligent function modules or bus conversion module connected to the CPU module
Module numbers are assigned to intelligent function modules in order of distance from the CPU module: No. 1 to No. 16.
• Products to which module numbers are not assigned
Module numbers are not assigned to the following extension devices.
• I/O module FX5-16EX/ES, FX5-16EYT/ES, etc.
• Expansion board FX5-232-BD, FX5-485-BD, etc.
• Expansion adapter FX5-232ADP, FX5-485ADP, etc.
• Extension power supply module FX5-1PSU-5V, FX3U-1PSU-5V
Ex.
Module No.
No.1 No.2 No.3 No.4
CPU module FX5 FX3 FX3

Expansion Bus
Input module Output module Intelligent Intelligent Intelligent
adapters Expansion conversion
FX5-16EX/ES FX5-16EYT/ES module module module
FX5-232ADP board module
FX5-40SSC-S FX3U-1PG FX3U-4AD
62 4.6 Numbers and Assignment in System
5 INSTALLATION
5.1 Installation Location

Use the PLC under the environmental conditions complying with the generic specifications (Page 17 Generic
Specifications).
Installation location in enclosure

To prevent temperature rise, do not mount the PLC on the floor or ceiling, or in the vertical direction. Always mount the PLC
horizontally on the wall as shown in the following figure.
Spaces in enclosure
Extension devices can be connected on the left and right sides of the CPU module of the PLC. Keep a space of at least 50
mm (1.97") between the module main body and other devices and structure.
If you intend to add extension devices, keep necessary spaces on the left and right sides.
A
FX5-232ADP
FX5-16EYT
FX5-16EX
A FX5U A
CPU module
A A ≥50 mm
(1.97")
Layout in enclosure
Keep a space of at least 50 mm (1.97") between the module main body or other devices and structure.
Expansion
adapter Extension module
module
module
A
Output
A FX5U Intelligent
Input
CPU module function module
A ≥50 mm (1.97")
For product dimensions or manual for various
products, refer to App 3 I/O Module.
5 INSTALLATION
5.1 Installation Location 63
5.2 Examination for Installation Method in Enclosure

Examine the installation location of PLC considering the environmental conditions (Page 17 Generic Specifications).
The PLC can be installed by the following two methods.
Keep a space of about 2 mm (0.08") between the products.
Installing on DIN rail

• The PLC can be installed on a DIN46277 rail (35 mm (1.38") wide).
• The PLC can be easily moved and removed.
• The PLC installation height is the same as the DIN rail.
For details on the procedures for installing on and detaching from DIN rail, refer to Page 65 Procedures for Installing on
and Detaching from DIN Rail.
■Example of installation
2 mm (0.08")
FX5U-32MR/ES FX5-16EX FX5-16EYT
DIN rail
Installing directly
• The PLC can be installed directly in the enclosure with M4 screws.
For mounting hole pitch, refer to Page 67 Hole pitches for direct mounting.
■Example of installation
2 mm (0.08")
FX5U-32MR/ES FX5-16EX FX5-16EYT (+ indicates an M4 screw.)
5 INSTALLATION
64 5.2 Examination for Installation Method in Enclosure
5.3 Procedures for Installing on and Detaching from

DIN Rail
The CPU module can be installed on a DIN46277 rail (35 mm (1.38") wide).
Preparation for installation
Connecting extension devices

Some extension devices must be mounted on the CPU module before the module is installed in the enclosure.
• Connect expansion adapters to the CPU module before mounting the PLC in the enclosure.
• Mount extension modules in the enclosure after mounting the CPU module in the enclosure.
• Expansion boards can be mounted on the CPU module after it is installed in the enclosure.
• Batteries can be replaced without dismounting the CPU module from the enclosure. However, if an expansion board is
used, the CPU module must be removed. 5
Affixing the dust proof sheet
The dust proof sheet should be affixed to the ventilation slits before beginning the installation and wiring work.
For the affixing procedure, refer to the instructions on the dust proof sheet.
Always remove the dust proof sheet when the installation and wiring work is completed.
Installation of CPU module

Connect the expansion adapter to the CPU module before mounting the PLC in the enclosure.
For the connection method of the expansion adapter, refer to Page 72 Connection method B - connection of an
expansion adapter.
1. Push out all DIN rail mounting hooks (A in the following figure).
1 1
1 A 1 A
2. Fit the upper edge of the DIN rail mounting groove (B in the following figure) onto the DIN rail.
3. Lock the DIN rail mounting hooks (C in the following figure) while pressing the PLC against the DIN rail.
C C
3 3
5 INSTALLATION
5.3 Procedures for Installing on and Detaching from DIN Rail 65
Installation of extension module

1. Push out the DIN rail mounting hook (A in the right Rear panel
figure) of the extension module.
A
2. Fit the upper edge of the DIN rail mounting groove (B in
the right figure) onto the DIN rail.
3. Push the product against the DIN rail.

B
4. Lock the DIN rail mounting hook while pressing the
product against the DIN rail.
3
5. Connect the extension cable. For the connecting procedure of the extension cable, refer to Page 71 Connection
Methods for CPU Module and Extension Devices.
Removal of CPU module

1. Open the terminal block cover, gradually loosen the left A
and right terminal block mounting screws (A in the right
figure), and remove the terminal blocks. For the
mounting procedure of the terminal block, refer to
Page 75 Removal and installation of removable
terminal block.
A
2. Disconnect the extension cables and the connecting
cables. When removing the extension cable, pull the
pullout tab of the extension cable straight up.
3. Insert the tip of a flathead screwdriver into the hole of
the DIN rail mounting hook (B in the right figure). This
step also applies for the DIN rail mounting hooks of the
C 5
expansion adapters.
4. Move the flathead screwdriver as shown in the right

figure to draw out the DIN rail mounting hooks of all
devices.
4
B
5. Remove the product from the DIN rail (C in the right 3
figure).
6. Push in the DIN rail mounting hooks (D in the right

figure).
6 D 6
5 INSTALLATION
66 5.3 Procedures for Installing on and Detaching from DIN Rail
5.4 Procedures for Installing Directly (with M4 Screws)

The product can be installed directly in the enclosure (with screws).
Position the holes so that there is a gap of about 2 mm (0.08") between the products.
Hole pitches for direct mounting

The product mounting hole pitches are shown below.
For pitch that varies depending on the product, refer to the table.
CPU module
Dimensions Model name Mounting hole pitch W
Unit: mm (inches)
5
22 FX5U-32MR/ES 123 (4.85")
(0.87") W 5 (0.2") FX5U-32MT/ES
FX5U-32MT/ESS
90 (3.55")
80 (3.15")
22 FX5U-64MR/ES 193 (7.6")

(0.87") W 5 (0.2") FX5U-64MT/ES
FX5U-64MT/ESS
FX5U-80MR/ES 258 (10.16")
FX5U-80MT/ES
90 (3.55")
80 (3.15")
B FX5U-80MT/ESS
Expansion adapter
Unit: mm (inches)
4 (0.16") W FX5-232ADP 15.1 (0.6")

FX5-485ADP
FX5-4AD-ADP
FX5-4DA-ADP
106 (4.18")
98 (3.86")
5 INSTALLATION
5.4 Procedures for Installing Directly (with M4 Screws) 67
I/O module
Unit: mm (inches)
20 (0.87") 20 (0.87") FX5-8EX/ES Refer to the figure shown to the left.

FX5-8EYR/ES
FX5-8EYT/ES
FX5-8EYT/ESS
90 (3.55")
80 (3.15")
FX5-16EX/ES
D FX5-16EYR/ES
FX5-16EYT/ES
FX5-16EYT/ESS
W FX5-32ER/ES 140 (5.52")

5 (0.2") 5 (0.2")
FX5-32ET/ES
FX5-32ET/ESS
90 (3.55")
80 (3.15")
Extension power supply module

Unit: mm (inches)
16 W FX5-1PSU-5V 34 (1.34")
(0.63")
80 (3.15")
90 (3.55")
FX3U-1PSU-5V 51 (2.01")
4(0.16") W
80 (3.15")
90 (3.55")
Bus conversion module

Unit: mm (inches)
FX5-CNV-BUS Refer to the figure shown to the left.
8 (0.32") 8 (0.32")
90 (3.55")
80 (3.15")
Intelligent function module

For the mounting hole dimensions of intelligent function modules, refer to user's manuals of each product.
5 INSTALLATION
68 5.4 Procedures for Installing Directly (with M4 Screws)
Hole pitches when extension module connected

Ex.
Unit: mm (inches)
15.1 22 123 (4.85") 27 38 (1.5") 44 (1.74") 14
(0.6") (0.87") (1.07") (0.56")
80 (3.15")
98 (3.86")
C A D F H
5
2*1 2*1 2*1 2*1
(0.08") (0.08") (0.08") (0.08")
FX5-232ADP FX5U-32MT/ES FX5-16EX/ES FX5-CNV-BUS
FX5-1PSU-5V FX3U-1PG
*1 The gap between products is 2 mm (0.08").
Installation of CPU module

Connect the expansion adapter to the CPU module before mounting the PLC in the enclosure.
For the connection method of the expansion adapter, refer to Page 72 Connection method B - connection of an
expansion adapter.
The FX5U-32M is used as the CPU module in this example.
1. Make mounting holes on the mounting surface according
to the external dimensions diagram.
2. Fit the CPU module (A in the right figure) to holes, and

secure it with M4 screws (B in the right figure). (In the B
case of FX5U-64M/80M, there are four screw holes.)
5 INSTALLATION
5.4 Procedures for Installing Directly (with M4 Screws) 69
Installation of extension module

1. Make mounting holes on the mounting surface Rear panel Rear panel
according to the external dimensions diagram.
2. Push in the DIN rail mounting hook (A in the right figure)

of the extension module. If the DIN rail mounting hook is
not pushed in, the screw hole is covered, and the
extension module cannot be mounted. (This procedure
may not be required, depending on the model.)
A
2
3. Fit the extension module (B in the right figure) to the
holes, and secure it with M4 screws (C in the right
figure).
5 INSTALLATION
70 5.4 Procedures for Installing Directly (with M4 Screws)
5.5 Connection Methods for CPU Module and

Extension Devices
This section explains the connection methods for extension devices.
Connection of extension devices

The connection method varies depending on the combination of products, i.e., the CPU module, expansion board, expansion
adapters, and extension modules.
The connection methods are explained with the following configuration example.
For connection method for FX5 extension power supply module (FX5-1PSU-5V), refer to MELSEC iQ-F FX5-1PSU-5V
HARDWARE MANUAL.
Expansion Expansion FX5 Bus conversion FX3

adapter board extension module module extension module
5
FX5U
CPU module
Connection Connection Connection Connection Connection Connection Connection

method B method A method C method D method D method E method D
Connection method A - connection of an expansion board

This subsection explains how to connect the expansion board to the CPU module.
1. Remove the expansion board connector cover from the Expansion board
front face of the CPU module. connector cover
2. Connect the expansion board to the expansion board

D
connector (C in the right figure).
E
3. Fix the expansion board (E in the right figure) with C 2
provided M3 tapping screws (D in the right figure) to the
CPU module.
• Tightening torque: 0.3 to 0.6Nm
5 INSTALLATION
5.5 Connection Methods for CPU Module and Extension Devices 71
Connection method B - connection of an expansion adapter

This subsection explains how to connect the expansion adapter to the CPU module.
1. Remove expansion adapter connector cover (A in the right
figure).
2. Slide the hook for coupling the expansion adapter of the

CPU module (B in the right figure).
2
2
1
B
A
3. Connect the expansion adapter to the CPU module as
shown in the right figure.
4. Slide the hook for coupling the expansion adapter of the

CPU module (B in the right figure) to fix the expansion B
adapter (C in the right figure).
C 4
3 4
3
C
Connection method C - connection of an extension module to the

CPU module
The procedure for connecting the extension module to the CPU module or powered input/output module is explained below.
1. Remove the extension connector cover (A in the right figure) A
on the right side of the surface of the CPU module or
powered input/output module. 3 C
2. Connect the extension cable (B in the right figure) from the
extension module to the extension connector of the CPU 1 B
module or powered input/output module. Put the pullout tab
(C in the right figure) of the extension cable inside the
extension connector cover.
3. Fit the extension connector cover (A in the right figure).
CPU module
5 INSTALLATION
72 5.5 Connection Methods for CPU Module and Extension Devices
Connection method D - connection between extension modules

The procedure for connecting the extension modules is explained below. (Powered input/output module are excluded.)
1. Remove the top cover (B in the right figure) of the existing B
module (left side) (A in the right figure).
2. Connect the extension cable (C in the right figure) of the D

module to be connected (right side) to the existing module 1 3 C
(left side) (A in the right figure).
3. Fit the top cover (B in the right figure). A
4. Pull out the pullout tab (D in the right figure) of the extension
cable on the right side of the cover.
Connection method E - connection of an extension module to the 5

bus conversion module
The procedure for connecting the extension module to the bus conversion module is explained below.
1. Connect the extension cable (A in the right figure) from the
extension module to the extension connector of the bus A
conversion module.
Cautions on mounting and removing extension cables

• Make sure that the pullout tab of extension cables do not touch the conductive parts of the module.
• When removing the extension cable, pull the pullout tab of the extension cable straight up.
5 INSTALLATION
5.5 Connection Methods for CPU Module and Extension Devices 73
6 WIRING
6.1 Wiring Preparations

Wiring procedure
Before wiring, make sure that the source power supply is off.
1. Prepare the parts for wiring.

Prepare crimp terminals and cables needed for wiring. (Page 76 Cable Connecting Procedure)
2. Wire the power supply terminals.

Connect the cables to the power [L] and [N] terminals.
Provide the protection circuit described in this chapter for the power supply circuit. (Page 79 Power Supply Wiring)
3. Perform class D grounding (grounding resistance: 100  or less) for the ground [ ] terminal.
Connect the grounded wire to the terminal. (Page 78 Grounding)
4. Wire the input [X] terminal.

When service power supply is used, select sink or source in the following wiring.
• For sink input, connect [24V][S/S] terminal
• For source input, connect [0V][S/S] terminal
Connect sensors and switches to the terminals. (Page 83 Input Wiring)
5. Wire the output [Y] terminal.

Connect the load to terminals. (Page 89 Output Wiring)
6. Wire built-in analog I/O terminal blocks.

Connect analog I/Os to terminals. (Page 98 Analog Wiring)
7. Wire the built-in RS-485 communication terminal blocks and Ethernet communication connectors.
8. Wire intelligent function modules, expansion boards, and expansion adapters.

User's manual for each intelligent function module
6 WIRING
74 6.1 Wiring Preparations
Removal and installation of removable terminal block
Removal
Loosen terminal block mounting screws on the left and right sides uniformly and remove the terminal block.
Installation
Place the terminal block at its predetermined position and tighten the terminal block mounting screws on the left and right
sides uniformly.
Tightening torque: 0.4 to 0.5 Nm
Precautions
Do not tighten the terminal block mounting screws with torque exceeding the specified range.
Failure to do so may cause equipment failures or malfunctions.
Make sure that there is no gap between the terminal block and mount position.
6 WIRING
6.1 Wiring Preparations 75
6.2 Cable Connecting Procedure

The cable connecting procedure is explained below.
Screw terminal block

Wire the screw terminal block in accordance with the following specifications.
For information concerning screw terminal blocks for intelligent function modules, refer to User's manual for each intelligent
function module.
Terminal block screw size and tightening torque

Model Terminal screw size Tightening torque
CPU module M3 0.5 to 0.8 Nm
I/O module
Extension power supply module
Intelligent function module Refer to manuals for each product.
Precautions
Do not tighten terminal screws with torque beyond the specified range. Otherwise it may cause equipment failure or
malfunction.
Wire end treatment

Crimp terminal size differs depending on terminal screw size and wiring methods used.
• Use crimp terminals of the following sizes.
■M3 terminal screw

• When a single wire is connected to a single terminal
φ3.2 (0.13") Terminal screw Crimp terminal

6.2 mm (0.24")
or less
φ3.2 (0.13")
6.2 mm (0.24") Terminal
or less
<Reference>
Manufacturer Model Supported standards Crimp tool
JST Mfg. Co., Ltd. FV1.25-B3A UL Listed YA-1
(JST Mfg. Co., Ltd.)
FV2-MS3
• When two wire are connected to a single terminal

φ3.2 (0.13")
6.2 mm (0.24") Terminal screw Crimp terminal
or less 6.3 mm (0.25")
or more
φ3.2 (0.13")
6.2 mm (0.24")
Terminal
or less
6.3 mm (0.25")
or more
<Reference>
Manufacturer Model Supported standards Crimp tool
JST Mfg. Co., Ltd. FV1.25-B3A UL Listed YA-1
(JST Mfg. Co., Ltd.)
6 WIRING
76 6.2 Cable Connecting Procedure
European-type terminal block

Wire the European-type terminal block in accordance with the following specifications.
Suitable wiring
Number of wires connected Wire size Tightening
per terminal Solid wire, Stranded Wire ferrule with torque
wire insulation sleeve
Built-in analog I/O terminal block One wire 0.2 to 0.5 mm2 (AWG24 to 20) 0.2 to 0.5 mm2 (AWG24 to 20) 0.22 to 0.25 Nm
Terminal block for built-in RS-485
Two wires 0.2 mm2 (AWG24) 
communication
Expansion board, expansion One wire 0.3 to 0.5 mm2 (AWG22 to 20) 0.3 to 0.5 mm2 (AWG22 to 20)
adapter 2
Two wires 0.3 mm (AWG22) 
Precautions
Do not tighten terminal screws with torque beyond the specified range. Otherwise it may cause equipment failure or
malfunction.
Wire end treatment 6

Treat stranded and solid wires as they are or use wire ferrules with insulation sleeves for wiring terminals.
■When stranded and solid wires are treated as they are

• Twist the end of stranded wires and make sure that there are no loose wires.
• Do not solder-plate the electric wire ends.
Stripping dimensions of electric wire ends
Built-in analog I/O terminal block, built-in RS-485 communication terminal block Expansion board, expansion adapter
5 mm 9 mm
(0.2") (0.36")
■When wire ferrules with insulation sleeves are used

Depending on the thickness of a wiring sheath used, it may be difficult to insert the sheath into an insulation sleeve. Refer to
the external dimensions as a reference to select wires.
Built-in analog I/O terminal block, built-in RS-485 communication terminal block Expansion board, expansion adapter
Insulating sleeve Contact area Insulating sleeve Contact area

(crimp area) (crimp area)
6 mm 8 mm
(0.23") (0.31")
2 to 2.5 mm 2.6 mm
(0.07" to 0.09") 10.5 to 12 mm (0.1") 14 mm
(0.41" to 0.47") (0.55")
<Reference>
Manufacturer Model Crimp tool
Built-in analog I/O terminal block Phoenix Contact GmbH & Co. KG AI 0.5-6 WH CRIMPFOX 6
Terminal block for built-in RS-485 communication CRIMPFOX 6T-F
Expansion board, expansion adapter AI 0.5-8 WH
6 WIRING
6.2 Cable Connecting Procedure 77
■Tool
For tightening terminals, use a small, commercially-available screwdriver with a straight tip. The recommended
shape is shown in the figure on the right.
■Precautions
With straight tip
When a precision screwdriver with a small grip is used, the specified tightening torque cannot be obtained. Use
the following screwdriver or equivalent product (grip diameter: 25 mm (0.99")) to obtain the tightening torque
specified above.
0.4 mm 2.5 mm
(0.01") (0.09")
<Reference>
Manufacturer Model
Phoenix Contact GmbH & Co. KG SZS 0.42.5
6.3 Grounding
Perform the following.
• Perform class D grounding (Grounding resistance: 100  or less).
• Ground the PLC independently when possible.
• If the PLC cannot be grounded independently, perform the "Common grounding" shown below.
Other Other Other

PLC equipment PLC equipment PLC equipment
Independent grounding Shared grounding Common grounding

(Best condition) (Good condition) (Not allowed)
PLC extension devices (excluding expansion boards and communication adapters)
PLC
Expansion Expansion CPU I/O Intelligent Other
adapter board module module module equipment
Independent grounding
class D grounding (grounding resistance: 100  or less)
• Use a grounding wire with thickness of AWG 14 (2 mm2) or thicker.
• Locate the ground point as close to the PLC as possible to minimize the length of the grounding wire.
6 WIRING
78 6.3 Grounding
6.4 Power Supply Wiring

Examples of AC power supply wiring
Power supply example for sink input [-common]

AC power supply (100 to 240 V)
Expansion adapter
5 V 0 V 24 V
Breaker
CPU module *1
L Power ON
Class D grounding
N PL
MC
5 V 0 V 24 V
S/S
0V MC Emergency
*4
24V stop
24 V DC
*2 service power
Input module S/S supply output MC MC 6
5 V 0 V 24 V
DC power
Powered supply
input/output module *1
L
N
DC AC
5 V 0 V 24 V
S/S
Power supply for loads
0V
*4 connected to PLC output
24V terminals
24 V DC
*3 service power As for emergency stop
FX5 supply output operation, see "DESIGN
intelligent module 24+
PRECAUTIONS" at
"Safety Precautions" field.
5 V 0 V 24 V 24-
Bus conversion
5 V 0 V 24 V module
*3
FX3 24+
intelligent module
5 V 0 V 24 V 24-
*1 Connect the AC power supply to the [L] and [N] terminals (common for 100 V AC system and 200 V AC system).
Make sure that the powered input/output module is turned on at the same time as the CPU module or earlier than the CPU module.
*2 Connect the [24V] terminal of the CPU module to the [S/S] terminal of the input module.
*3 Some intelligent function modules may not have power supply terminals.
When using an external power supply, turn on the power supply at the same time as the CPU module or earlier than the CPU module.
When turning off the power, confirm the safety of the system and turn off the power of the PLC (including extension devices) at the same
time.
*4 Do not connect the [24V] terminals (24 V DC service power supply) of the CPU module and the powered input/output module with each
other. Connect the [0V] terminal.
6 WIRING
6.4 Power Supply Wiring 79
Power supply example for source input [+common]

Expansion adapter
5 V 0 V 24 V
Breaker
CPU module *1
L Power ON
Class D grounding
N PL
MC
5 V 0 V 24 V
S/S
0V MC Emergency
*4
24V stop
24 V DC
*2 service
power supply
Input module S/S MC MC
output
5 V 0 V 24 V
DC power
Powered input/output supply
module *1
L
N
DC AC
5 V 0 V 24 V
S/S
Power supply for loads
0V connected to PLC output
*4 terminals
24V
24 V DC
service As for emergency stop
*3 operation, see "DESIGN
FX5 power supply
24+ PRECAUTIONS" at "Safety
intelligent module output
Precautions" field.
5 V 0 V 24 V 24-
Bus conversion
5 V 0 V 24 V module
*3
FX3 24+
intelligent module
5 V 0 V 24 V 24-
*1 Connect the AC power supply to the [L] and [N] terminals (common for 100 V AC system and 200 V AC system).
Make sure that the powered input/output module is turned on at the same time as the CPU module or earlier than the CPU module.
time.
*4 Do not connect the [24V] terminals (24 V DC service power supply) of the CPU module and the powered input/output module with each
other. Connect the [0V] terminal.
6 WIRING
80 6.4 Power Supply Wiring
Wiring example for an extension power supply module (sink input [-common])
The following example shows wiring for an extension power supply module when sink input [-common] is used.
Expansion adapter
5 V 0 V 24 V
Breaker
CPU module *1
Power ON
L
Class D grounding
PL
N MC
S/S
5 V 0 V 24 V MC
0V Emergency
stop
24V
24 V DC
service power
*2
Input module supply output MC MC
5 V 0 V 24 V S/S
*3 DC power
FX5 24+ supply
intelligent module 6
5 V 0 V 24 V 24-
DC AC
Power supply for loads connected
Extension power supply module *1 to PLC output terminals
L
As for emergency stop operation,
see "DESIGN PRECAUTIONS" at
N
"Safety Precautions" field.
5 V 0 V 24 V
Wiring precaution:
*3 Run grounding and power cables from the
FX5 24+ top as shown in the following figure.
intelligent module
5 V 0 V 24 V 24- Grounding and
power cables
*2
Input module S/S
5 V 0 V 24 V
Output module
5 V 0 V 24 V
When external power supply is

supplied to the input circuit
S/S
*1 Connect the AC power supply to the [L] and [N] terminals (common for 100 V AC system and 200 V AC system). Make sure that the
power of the extension power supply module is turned on at the same time as the CPU module or earlier than the CPU module.
time.
6 WIRING
6.4 Power Supply Wiring 81
Wiring example for an extension power supply module (source input [+common])
The following example shows wiring for an extension power supply module when source input [+common] is used.
Expansion adapter
5 V 0 V 24 V
Breaker
CPU module *1
Power ON
L Class D grounding
PL
N MC
5 V 0 V 24 V S/S
MC
0V Emergency
24V stop
24 V DC
*2 service
Input module power supply MC MC
S/S
5 V 0 V 24 V output
*3 DC power
FX5 24+ supply
intelligent module
5 V 0 V 24 V 24-
DC AC
Power supply for loads connected
Extension power supply module *1 to PLC output terminals
L
As for emergency stop operation, see
N "DESIGN PRECAUTIONS" at "Safety
5 V 0 V 24 V Precautions" field.
Wiring precaution:
*2 Run grounding and power cables from the
Input module S/S top as shown in the following figure.
5 V 0 V 24 V
Grounding and
*3 power cables
FX5 24+
intelligent module
5 V 0 V 24 V 24-
Output module
5 V 0 V 24 V
When external power supply is

supplied to the input circuit
S/S
*1 Connect the AC power supply to the [L] and [N] terminals (common for 100 V AC system and 200 V AC system). Make sure that the
power of the extension power supply module is turned on at the same time as the CPU module or earlier than the CPU module.
time.
6 WIRING
82 6.4 Power Supply Wiring
6.5 Input Wiring

The input wiring of the CPU module and I/O modules is explained below.
24 V DC input (Sink and source input type)

For input specifications of the CPU module, refer to Page 19 Input Specifications.
For input specifications of the I/O modules, refer to Page 135 Input specifications.
Sink and source input

■Differences between the sink input circuit and the source input circuit
• Sink input [-common] • Source input [+common]
Sink input means a DC input signal with current-flow from the input Source input means a DC input signal with current-flow into the
(X) terminal. input (X) terminal.
When a device such as a transistor output type sensor is When a device such as a transistor output type sensor is
connected, NPN open collector transistor output can be used. connected, PNP open collector transistor output can be used.
L L
N N
24V 24V
6
0V 0V
S/S S/S
X X
■Switching between sink/source inputs

To switch the input type to sink or source input, wire the [S/S] terminal to the [0V] or [24V] terminal.
• Sink input: Connect the [24V] terminal and [S/S] terminal. (Page 87 Sink input [AC power supply type])
• Source input: Connect the [0V] terminal and [S/S] terminal. (Page 88 Source input [AC power supply type])
All inputs (X) of the CPU module can be set to either sink input or source input by selection.
6 WIRING
6.5 Input Wiring 83
Handling of 24 V DC input
■Input terminal
• Sink input • Source input
When a no-voltage contact or NPN open collector transistor output When a no-voltage contact or PNP open collector transistor output
is connected between an input (X) terminal and the [0V] terminal is connected between an input (X) terminal and the [24V] terminal
and the circuit is closed, the input (X) turns on. and the circuit is closed, the input (X) turns on.
The input display LED turns on. The input display LED turns on.
Fuse Fuse
L L
N N
100 to 240 V AC 100 to 240 V AC
S/S S/S
0V 0V
24V 24V
* X000 * X000
X001 X001
X007 X007
*Input impedance *Input impedance
• RUN terminal setting

X000 to X017 of the CPU module can be used as RUN input terminals
by setting parameters.
MELSEC iQ-F FX5 User's Manual (Application)
■Input circuit
• Function of input circuit
The primary and secondary circuits for input are insulated with a photocoupler, and the second circuit is provided with a C-R filter.
The C-R filter is designed to prevent malfunctions caused by chattering of the input contact and noise from the input line.
Input has a response delay switching from ON to OFF and OFF to ON, shown in the following table.
Item Specifications
Input response time FX5U-32M X000 to X005 ON: 2.5 s or less
(H/W filter delay) OFF: 2.5 s or less
FX5U-64M, X000 to X007
FX5U-80M
FX5U-32M X006 to X017 ON: 30 s or less
OFF: 50 s or less
FX5U-64M, X010 to X017
FX5U-80M
FX5U-64M, X020 and ON: 50 s or less
FX5U-80M subsequent OFF: 150 s or less
I/O module
• Change of filter time

All input circuits have digital filters, and the input response time shown in the following table can be added by setting parameters.
When using this product in an environment with much noise, set the digital filter.
Item Specifications
Input response time None, 10 s, 50 s, 0.1 ms, 0.2 ms, 0.4 ms, 0.6 ms, 1 ms, 5 ms, 10 ms (initial values), 20 ms, 70 ms
(Digital filter setting value)
■Input sensitivity
For input signal current and Input sensitivity current of the CPU module, refer to Page 19 Input Specifications.
For input signal current and Input sensitivity current of the I/O modules, refer to Page 135 Input specifications.
6 WIRING
84 6.5 Input Wiring
Precautions for connecting input devices

■In the case of no-voltage contact
Use input devices appropriate for low electric current.
If no-voltage contacts for high current (switches) are used, contact failure may occur.
■In the case of input device with built-in series diode

The voltage drop of the series diode should be the following value or less.
Also make sure that the input current is over the input-sensing level while the switches are on.
Item Specifications
Voltage drop FX5U-32M X000 to X005 3.9 V
FX5U-64M, X000 to X007
FX5U-80M
FX5U-32M X006 to X017 4.1 V
FX5U-64M, X010 to X017
FX5U-80M
FX5U-64M, X020 and 2.4 V
FX5U-80M subsequent
I/O module
6
■In the case of input device with built-in parallel resistance
Use a device having a parallel resistance Rp (k) of the following value or more.
Item Specifications
Parallel resistance Rp (k) FX5U-32M X000 to X005 14
FX5U-64M, X000 to X007
FX5U-80M
FX5U-32M X006 to X017 15
FX5U-64M, X010 to X017
FX5U-80M
FX5U-64M, X020 and 13
I/O module
If the resistance is less than the above parallel resistance Rp (k), connect a bleeder resistance Rb (k) obtained by the
following formula as shown in the following figure.
Item Specifications
Bleeder resistance Rb (k) FX5U-32M X000 to X005 5 Rp / (14-Rp) or less
FX5U-64M, X000 to X007
FX5U-80M
FX5U-32M X006 to X017 4 Rp / (15-Rp) or less
FX5U-64M, X010 to X017
FX5U-80M
FX5U-64M, X020 and 6 Rp / (13-Rp) or less
I/O module
24V Bleeder 0V Bleeder

resistance resistance
S/S Rb S/S Rb
PLC PLC
(sink input) X (source input) X
Rp Rp
0V 24V
6 WIRING
6.5 Input Wiring 85
■ In the case of 2-wire proximity switch

Use a two-wire proximity switch whose leakage current, I is 1.5 mA or less when the switch is off.
If the resistance is larger than leakage current, I of 1.5 mA, connect a bleeder resistance Rb (k), obtained by the following
formula as shown in the following figure.
Item Specifications
Bleeder resistance Rb (k) FX5U-32M X000 to X005 7 / (I-1.5) or less
FX5U-64M, X000 to X007
FX5U-80M
FX5U-32M X006 to X017 7 / (I-1.5) or less
FX5U-64M, X010 to X017
FX5U-80M
FX5U-64M, X020 and 9 / (I-1.5) or less
I/O module
Bleeder Bleeder
24V resistance 0V resistance
2-wire 2-wire
S/S Rb proximity S/S Rb proximity
PLC I sensor PLC I sensor
(sink input) X (source input) X
0V 24V
■When the input signal cannot be received because the current is insufficient
The current rating for the CPU module in X020 or more and the I/O module is 4 mA.
In some cases, depending on extension devices used, it may not be possible to receive the input signal, due to the insufficient
current. Take the following action in such case.
Input current
Adjusted in accordance
with the connected device
PLC Proximity sensor
5.6 k
X
Main circuit
S/S
External resistor
(for input current adjustment)
In the case of capturing high-speed pulses

When capturing pulses of a response frequency of 50 to 200 kHz on using the input X000 to X007 (FX5U-32M is X000 to
X005.), wire the terminals as stated below.
• The wiring length should be 5 m (16'4") or less.
• Use shielded twisted-pair cables for connecting cables. Ground the shield of each shielded cable only on the CPU module
side.
• Connect a 1.5 k (1 W or more) bleeder resistance to the input terminal, so that the sum of the load current of the open
collector transistor output on the mating device and the input current of the CPU module is 20 mA or more.
The above-mentioned restrictions are due to specifications of connecting device (encoder etc.).
Please adjust the cable length and load, for connecting device.
6 WIRING
86 6.5 Input Wiring
Input wiring example
Sink input [AC power supply type]

CPU module Fuse *1
L
Class D grounding
N
*3
S/S
0V
0V
24V
24V
Three-wire
X0 sensor
X1
Input Input
5V 0V 24V impedance terminal
6
Input module
S/S
Two-wire
X0 proximity
*2 sensor
X1
5V 0V 24V
Input
terminal
Input module 24 V DC
S/S
X0
X1 Three-wire
5V 0V 24V
Input sensor
terminal
*1 Handle the power supply circuit properly in accordance with "Power Supply Wiring."
*2 For an input device having a parallel resistance or a two-wire proximity switch, a bleeder resistance may be required.
*3 In the case of sink input wiring, short-circuit the [S/S] and [24V] terminals of the CPU module.
The service power supply or external power supply can be used for all inputs (X) of the CPU module. However
you need to select either one for each CPU module or I/O module. Both power supplies cannot be used
together in the same module.
6 WIRING
6.5 Input Wiring 87
Source input [AC power supply type]

CPU module Fuse *1
L
Class D grounding
*3
S/S
0V
0V Three-wire
24V
24V sensor
X0
X1
Input
Input
impedance
terminal
5V 0V 24V
Two-wire
Input module proximity
S/S sensor
X0
X1
5V 0V 24V *2
Input
terminal
Input module 24 V DC
S/S
X0
Three-wire
X1
5V 0V 24V sensor
Input
terminal
*1 Handle the power supply circuit properly in accordance with "Power Supply Wiring."
*2 For an input device having a parallel resistance or a two-wire proximity switch, a bleeder resistance may be required.
*3 In the case of source input wiring, short-circuit the [S/S] and [0V] terminals of the CPU module.
The service power supply or external power supply can be used for all inputs (X) of the CPU module. However
you need to select either one for each CPU module or I/O module. Both power supplies cannot be used
together in the same module.
6 WIRING
88 6.5 Input Wiring
6.6 Output Wiring

The output wiring of the CPU module and I/O modules is explained below.
Relay output
For output specifications of the CPU module, refer to Page 21 Output Specifications.
For output specifications of the I/O modules, refer to Page 136 Output specifications.
Product life of relay output contacts

The product life of relay output contacts varies considerably depending on the load type used.
Note that loads generating reverse electromotive force or rush current may cause poor contact or welding of contacts which
may lead to considerable reduction of the contact product life.
■Inductive load
Inductive loads generate large reverse electromotive force between contacts at shutdown, which may cause arc discharge. At
a fixed current consumption, as the power factor (phase between current and voltage) gets smaller, the arc energy gets larger.
The standard life of contacts used for inductive AC loads, such as general contactors and solenoid valves, is 500,000
operations at 20 VA. 6
The following table shows the approximate life of a relay based on the results of an operation life test.
• Test condition: 1 sec. ON/1 sec. OFF
Load capacity Contact life
20 VA 0.2 A/100 V AC 3,000,000 times
0.1 A/200 V AC
35 VA 0.35 A/100 V AC 1,000,000 times
0.17 A/200 V AC
80 VA 0.8 A/100 V AC 200,000 times
0.4 A/200 V AC
The product life of relay contacts becomes considerably shorter than the above conditions when the rush overcurrent is shut
down.
Please refer to the following measures regarding the inductive load.
Page 91 Contact protection circuit for inductive loads
Some types of inductive loads generate rush current 5 to 15 times the stationary current at activation. Make sure that the rush
current does not exceed the current corresponding to the maximum specified resistance load.
■Lamp load
Lamp loads generally generate rush current 10 to 15 times the stationary current. Make sure that the rush current does not
exceed the current corresponding to the maximum specified resistance load.
■Capacitive load
Capacitive loads can generate rush current 20 to 40 times the stationary current. Make sure that the rush current does not
exceed the current corresponding to the maximum specified resistance load.
Capacitive loads such as capacitors may be present in electronic circuit loads including inverters.
■Resistance load
For maximum load specifications of resistance load, refer to the following.
6 WIRING
6.6 Output Wiring 89
Handling of relay output

■Output terminal
One common terminal is used for 4 or 8 relay output points.
The common terminal blocks can drive loads of different circuit voltage systems (for example,100 V AC and 24 V DC).
Load
Y0
Y1
Fuse 24 V DC
COM0
Load
Y4
Y5
Fuse 100 V AC
COM1
PLCs
■External power supply

Use an external power supply of 30 V DC or less or 240 V AC or less (250 V AC or less when the module does not comply
with CE, UL, cUL standards) for loads.
■Insulation of circuit
The PLC internal circuit and external load circuits are electrically insulated between the output relay coil and contact.
The common terminal blocks are separated from one another.
■Display of operation
When power is applied to the output relay coil, the LED is lit, and the output contact is turned on.
■Response time
The response time of the output relay from when the power is applied to the coil until the output contact is turned on and from
when the coil is shut off until the output contact is turned off is approx. 10 ms.
■Output current
At a circuit voltage of 240 V AC or less (250 V AC or less when the module does not comply with CE, UL, cUL standards), a
resistance load of 2 A per point or an inductive load of 80 VA or less (100 V AC or 200 V AC) can be driven.
For the life of the contact for switching an inductive load, refer to Page 89 Inductive load.
When an inductive load is switched, connect a diode (for commutation) or a surge absorber in parallel with this load.
DC circuit AC circuit
Diode (for commutation) Surge absorber
■Open circuit leakage current

There is no leakage current when the outputs are OFF.
6 WIRING
90 6.6 Output Wiring
Wiring precautions
■Protection circuit for load short-circuiting
A short-circuit at a load connected to an output terminal could cause
burnout at the output element or the PCB. To prevent this, a protection Load
Y0
fuse should be inserted at the output. Fuse
COM0
PLCs
■Contact protection circuit for inductive loads

An internal protection circuit for the relays is not provided for the relay output circuit in this product. It is recommended to
use inductive loads with built-in protection circuits.
When using loads without built-in protection circuits, insert an external contact protection circuit, etc. to reduce noise and
extend product life.
• DC circuit
+ -
Connect a diode in parallel with the load. Inductive load
The diode (for commutation) must comply with the following
specifications.
PLC output contact 6
Diode (for commutation)
 Reverse voltage: 5 to 10 times the load voltage
 Forward current: Load current or more
• AC circuit
Connect a surge absorber (CR composite parts like surge killer, Inductive load
spark killer, etc.) parallel to the load. Select a surge absorber with
PLC output contact
voltage rating that is suitable for the output used.
Surge
 Electrostatic capacity: Approx. 0.1 F absorber
 Resistance: Approx. 100 to 200 
■Interlock
For loads such as forward/reverse contactors, etc., where a
hazardous condition could result if switched ON simultaneously, an Interlock Limit of forward
rotation Forward
external interlock should be provided for interlocking along with an PLC output
rotation
Limit of reverse
interlock in the PLC program, as shown to the right. contact
rotation Reverse
rotation
PLC output
contact
■In-phase
PLC output contacts (*) should be used in an "in-phase" manner.
*
6 WIRING
Transistor output
Sink and source output

Sink output and source output products are available for transistor outputs of the CPU module and I/O modules.
■Differences in circuit
• Sink output [-common] • Source output [+common]
Output to make load current flow into the output (Y) terminal is Output to make load current flow out of the output (Y) terminal
called sink output. is called source output.
Load Load
Y Y
COM +V
Fuse Fuse
DC power supply DC power supply
A number is entered in the  of [COM]. A number is entered in the  of [+V].
Handling of transistor output

■Output terminal
4 or 8 transistor output points are covered by one common terminal.
• Sink output • Source output
Connect each COM (number) terminal to the minus side of Connect +V (number) terminal to the plus side of the load
the load power supply. power supply.
The COM terminals are not connected internally. The +V terminals are not connected internally.
Sink output type Source output type
Load Load
Y0 Y0
Y1 Y1
DC power DC power
Fuse supply Fuse supply
COM0 +V0
Load Load
Y4 Y4
Y5 Y5
DC power DC power
Fuse supply Fuse supply
COM1 +V1
PLCs PLCs
■External power supply

For driving the load, use a smoothing power supply of 5 to 30 V DC that can output current two or more times the current
rating of the fuse connected to the load circuit.
■Insulation of circuit
The internal circuit of the PLC and the output transistor are insulated with a photocoupler.
The common blocks are separated from one another.
■Display of operation
Operation indicator LEDs are built into the CPU module and output modules, and turn ON when photocouplers are activated,
and the transistors are switched on.
6 WIRING
■Response time
Time taken from when the photocoupler of the module is driven (or shut off) to when the transistor is turned on (or off) differs
depending on the output terminal used. For specifications of each module, refer to the following.
The transistor OFF time is longer under lighter loads. For example, under a load of 24 V DC 40 mA, the
response time is approx. 0.3 ms.
When response performance is required under light loads, provide a dummy resistor as shown below to
increase the load current.
• Sink output type • Source output type
Dummy PLCs Dummy PLCs

Fuse Load Fuse Load
resistor resistor
Y Y
COM0 +V0 6
■Output current
Maximum load differs for each module. For specifications of each module, refer to the following.
When driving a semiconductor device, carefully check the input voltage characteristics of the device.
■Open circuit leakage current

0.1 mA or less
Wiring precautions
■Protection circuit for load short-circuiting
A short-circuit at a load connected to an output terminal could cause burnout at the output device or the PCB.
To prevent this, a protection fuse should be inserted at the output. Use a load power supply capacity that is at least 2
times larger than the load current.
Load Load
Y Y
Fuse Fuse
COM0 +V0
PLCs PLCs
6 WIRING
■Contact protection circuit for inductive loads

When an inductive load is connected, connect a diode (for commutation) in parallel with the load as necessary.
The diode (for commutation) must comply with the following specifications.
Standard
Reverse voltage 5 to 10 times as high as the load voltage
Forward current Load current or larger
Inductive load Inductive load

Y Y
Fuse Fuse
COM0 +V0
PLCs PLCs
■Interlock
For loads such as forward/reverse contactors, etc., where a hazardous condition could result if switched ON simultaneously,
an external interlock should be provided for interlocking along with an interlock in the PLC program, as shown below.
+ - - Limit of forward +
Limit of forward
rotation Interlock rotation Interlock
Forward rotation Forward rotation
Reverse rotation Reverse rotation

Limit of reverse PLC output Limit of reverse PLC output
rotation element rotation element
6 WIRING
Output wiring example
Relay output
CPU module
Fuse *1 relay output
Breaker COM0
Y0
Power ON *1
Fuse
COM1
PL MC Y4
Fuse *1
MC COM3
Emergency
stop Y14
MC MC
*2
*1 Output module
Fuse
COM0 relay output 6
DC power Y0
supply
Y7
Load
Fuse *1
COM1
Y0
Y7
Load
Power supply for loads connected to
PLC output terminals
As for emergency stop operation, see "DESIGN

PRECAUTIONS" at "Safety Precautions" field.
*1 The output circuit of the PLC does not have a built-in fuse.
Provide a fuse suitable for each load to prevent melting of the wires on the circuit board caused by output device breakdown due to load
short-circuiting.
*2 "" represents vacant terminals.
6 WIRING
Transistor output
■Sink output type
AC power supply (100 to 240 V) CPU module transistor
Fuse *1 output (sink)
COM0
Y0
Breaker Load
Power ON COM1
Y4
PL Fuse *1
MC
COM3
MC Y14
Emergency Load
stop *2
MC MC
Output module
Fuse *1 transistor output (sink)
COM0
Y0
DC power supply
Y7
Load
Fuse *1
COM1
Y0
Y7
Load


short-circuiting.
6 WIRING
■Source output type

AC power supply (100 to 240 V) CPU module transistor
Fuse *1 output (source)
+V0
Breaker Y0
Load
Power ON +V1
Y4
PL Fuse
MC
+V3
MC Y14
Emergency Load
stop
*2
MC MC
Output module transistor

*1 output (source)
Fuse
+V0
Y0
DC power supply
Load
Y7 6
Fuse
+V1
Y0
Y7
Load

short-circuiting.
6 WIRING
6.7 Analog Wiring

Wiring to the built-in analog I/O terminals of the CPU module is explained below.
For specifications of the built-in analog I/O terminals of the CPU module, refer to Page 25 Built-in Analog Specifications.
Analog input wiring
Shield *1 82.7 k CH

V+
V-
*2 33 k
Class D
grounding CH No. goes in  of V+, CH.
*1 For analog input wiring, use shielded twisted-pair cables (double-core type). Separate them from other power lines or lines which can be
induced by others.
*2 For unused channels, short-circuit the "V+" and "V-" terminals.
Analog output wiring
*1 Shield
V+
V-
*2 Class D grounding
*1 For analog output wiring, use shielded twisted-pair cables (double-core type). Separate them from other power lines or lines which can
be induced by others.
*2 Ground a shielded cable at one point on the signal receiving side.
6 WIRING
98 6.7 Analog Wiring
6.8 Examples of Wiring for Various Uses
Notes about examples of wiring

The examples of wiring are given under the following conditions.
■Input/output number
The input/output numbers are the actual numbers on the program (They may differ from the numbers shown on the product
terminals).
■Input/output specifications of products

Check the input/output specifications of products and examples of wiring.
• There are products for sink output and for source output.
■Examples of program
The examples of programming (instructions) are given based on the allocation of the input/output numbers for wiring.
For the instructions, refer to MELSEC iQ-F FX5 Programming Manual (Instructions,Standard Functions/Function Blocks).
Built-in positioning function

6
For wiring examples for the built-in positioning function, refer to MELSEC iQ-F FX5 User's Manual (Positioning Control).
Communication function
For wiring of the built-in RS-485 communication terminal block, communication boards and communication adapters, refer to
the following.
For wiring of the built-in Ethernet, refer to the following.
6 WIRING
6.8 Examples of Wiring for Various Uses 99
High-speed counter
Examples of wiring for high-speed counters are shown below.
When capturing pulses of a response frequency of 50 to 200 kHz, refer to Page 86 In the case of capturing high-speed
pulses.
For details on the high-speed counters, refer to MELSEC iQ-F FX5 User's Manual (Application).
For the programs, refer to MELSEC iQ-F FX5 Programming Manual (Instructions, Standard Functions/Function Blocks).
1-phase 1-count
The wiring examples in this section use the following settings. When settings other than those in the table are used, use the
examples shown in the following figures as references for wiring.
CH to be used Pulse input mode External preset input External enable input Operation mode
CH1 1-phase 1-input (S/W) Invalid Invalid Normal mode
The settings of the high-speed counters are set by using the parameter settings of the engineering tool.
For details, refer to MELSEC iQ-F FX5 User's Manual (Application).
■Example of wiring
• NPN open collector transistor output rotary encoder
In the case of sink wiring
Rotary encoder
Fuse 24 V DC
L 24V
Class D grounding *1
0V
N
S/S
0V
24V A phase
1.5 k
X000 B phase
Z phase
CPU module
• PNP open collector transistor output rotary encoder

In the case of source wiring
Rotary encoder
Fuse 24 V DC
L 24V
Class D grounding*1
0V
N
S/S
0V
24V A phase
1.5 k
X000 B phase
Z phase
CPU module
*1 The grounding resistance should be 100  or less.
6 WIRING
100 6.8 Examples of Wiring for Various Uses
■Example of wiring (When 24 V DC external power supply is used)

Rotary encoder
Fuse 24 V DC
L 24V
0V
N
S/S
0V
24V A phase
1.5 k
X000 B phase
Z phase
CPU module

In the case of source wiring 6
Rotary encoder
Fuse 24 V DC
L 24V
Class D grounding*1
0V
N
S/S
0V
24V A phase
1.5 k
X000 B phase
Z phase
CPU module
6 WIRING
2-phase 2-count
The wiring examples in this section use the following settings. When settings other than those in the table are used, use the
examples shown in the following figures as references for wiring.
CH to be used Pulse input mode External preset input External enable input Operation mode
CH2 2-phase 2-input Invalid Invalid Normal mode
The settings of the high-speed counters are set by using the parameter settings of the engineering tool.
For details, refer to GX Works3 Operating Manual.
Rotary encoder
Fuse 24 V DC
L 24V
0V
N
S/S
0V
1.5 k
24V A phase
X002 B phase
X003 Z phase
CPU module

Rotary encoder
Fuse 24 V DC
L 24V
Class D grounding*1
0V
N
S/S
0V
24V A phase
1.5
k
X002 B phase
X003 Z phase
CPU module
6 WIRING
■Example of wiring (When 24 V DC external power supply is used)

Rotary encoder
Fuse 24 V DC
L 24V
0V
N
S/S
0V
1.5 k
24V A phase
X002 B phase
X003 Z phase
CPU module

6
Rotary encoder
Fuse 24 V DC
L 24V
Class D grounding*1
0V
N
S/S
0V
24V 1.5 A phase
k
X002 B phase
X003 Z phase
CPU module
6 WIRING
Interruption
Examples of wiring for when the input interruption function of the CPU module is used are shown below.
The same wiring is used for the pulse catch and pulse width measurement functions.
When capturing pulses of a response frequency of 50 to 200 kHz, refer to Page 86 In the case of capturing high-speed
pulses.
For details on the input interruption function, pulse catch function and pulse width measurement function, refer to
MELSEC iQ-F FX5 User's Manual (Application).
Example of wiring
■When 24 V DC service power supply is used
In the case of sink wiring In the case of source wiring
Fuse Fuse
L L
Class D grounding *1 Class D grounding *1
N N
S/S S/S
0V 0V
24V 24V
1.5 k 1.5 k
3-wire type
X000 X000
3-wire type
CPU module CPU module
■When 24 V DC external power supply is used
In the case of sink wiring In the case of source wiring
Fuse Fuse
L L
Class D grounding *1 Class D grounding*1
N 24 V DC N 24 V DC
S/S S/S
0V 0V
24V 24V
1.5 k 1.5 k
3-wire type
X000 X000
3-wire type
6 WIRING
Digital Switch
When DSW instructions are used

Examples of wiring for capturing values from a 4-digit digital switch to the data register D100 are given below.
For the instructions, refer to MELSEC iQ-F FX5 Programming Manual (Instructions, Standard Functions/Function Blocks).
■Example of program
SM400
DSW X010 Y010 D100 K1
• Sink wiring
The example is the wiring for the input/output of the FX5U-32MT/ES.
Digital 100 101 102 103

switch of
BCD
6
0.1A 50V
diode is
necessary.
1 2 4 8
S/S 0V 24V X010 X011 X012 X013 X014 X015 X016 X017
Sink input
Transistor output (sink)

FX5U-32MT/ES
COM2 Y010 Y011 Y012 Y013
100 101 102 103
• Source wiring
The example is the wiring for the input/output of the FX5U-32MT/ESS.
Digital
switch of
BCD
100 101 102 103
0.1A 50V
diode is
necessary.
1 2 4 8
S/S 0V 24V X010 X011 X012 X013 X014 X015 X016 X017
Source input
Transistor output (source)

FX5U-32MT/ESS
+V2 Y010 Y011 Y012 Y013
100 101 102 103
6 WIRING
When BIN instructions are used

Examples of wiring for capturing values from a 2-digit digital switch to the data register D102 are given below.
SM400
BIN K2X010 D102
• Sink wiring
100 101
1 2 4 8 1 2 4 8
S/S 0V 24V X010 X011 X012 X013 X014 X015 X016 X017
Sink input
FX5U-32MT/ES
• Source wiring
100 101
1 2 4 8 1 2 4 8
S/S 0V 24V X010 X011 X012 X013 X014 X015 X016 X017
Source input
FX5U-32MT/ESS
6 WIRING
Input Matrix
Examples of wiring to take ON/OFF status of 24 switches by using MTR instructions are given below.
Example of program
SM400
MTR X010 Y010 M30 K3
Example of wiring
• Sink wiring
M50
M51
M52
M53
M54
M55
M56
M57
X011 X013 X015 X017
X012 X014 X016
M40
M41
M42
M43
M44
M45
M46
M47
0.1A 50V
diode is
6
necessary.
X011 X013 X015 X017
X012 X014 X016
M30
M31
M32
M33
M34
M35
M36
M37
To use
X000 to X017
of the input, S/S 0V 24V X010 X011 X012 X013 X014 X015 X016 X017
connect a Sink input
pull-up resistor
(3.3 k/0.5 W).
FX5U-32MT/ES
COM2 Y010 Y011 Y012 Y013
• Source wiring
M50
M51
M52
M53
M54
M55
M56
M57
X011 X013 X015 X017

X012 X014 X016
M40
M41
M42
M43
M44
M45
M46
M47
0.1A 50V
diode is
necessary.
X011 X013 X015 X017
X012 X014 X016
M30
M31
M32
M33
M34
M35
M36
M37
To use
X000 to X017
of the input, S/S 0V 24V X010 X011 X012 X013 X014 X015 X016 X017
connect a Source input
pull-up resistor
(3.3 k/0.5 W).
FX5U-32MT/ESS
+V2 Y010 Y011 Y012 Y013
6 WIRING
Seven Segment with Latch

When SEGL instructions are used

Examples of wiring for displaying the current value of D100 on the 4-digit 7-segment display are given below.
SM400
SEGL D100 Y010 K1
• Sink wiring
FX5U-32MT/ES

COM2 Y010 Y011 Y012 Y013 COM3 Y014 Y015 Y016 Y017
7-segment display to be used for sink wiring
1 2 4 8 100 101 102 103 (in the case of transistor output)
Seven Segment
PLC with Latch
103 102 101 100
1 *1 +
2
4
8 Y Signal Internal
circuit
Fuse
COM1 -
• Source wiring
FX5U-32MT/ESS

+V2 Y010 Y011 Y012 Y013 +V3 Y014 Y015 Y016 Y017
7-segment display to be used for source wiring
Seven Segment
PLC with Latch
103 102 101 100
1 *1 +V0 +
2
4
8 Y Signal Internal
circuit
Fuse
-
*1 Use a 7-segment display with a latch and a built-in BCD decoder.
6 WIRING
When BCD instructions are used

Examples of wiring for displaying the current value of D100 on the 2-digit 7-segment display are given below.
SM400
BCD D100 K2Y010
• Sink wiring
FX5U-32MT/ES

COM2 Y010 Y011 Y012 Y013 COM3 Y014 Y015 Y016 Y017
7-segment display to be used for sink wiring
Seven Segment
PLC with Latch
12 48 1 248
*1
6
+
Y Signal Internal
circuit
Fuse
COM1 -
• Source wiring
FX5U-32MT/ESS

+V2 Y010 Y011 Y012 Y013 +V3 Y014 Y015 Y016 Y017
7-segment display to be used for source wiring
Seven Segment
PLC with Latch
12 48 1 248
*1 +
+V0
Y Signal Internal
circuit
Fuse
-
*1 Use a 7-segment display with a latch and a built-in BCD decoder.
6 WIRING
7 OPERATION ADJUSTMENT
7.1 Preparation for Operation

Preliminary inspection
Incorrect connection of the power supply terminal, contact of the DC input wire and power supply wire, or short-circuiting of
output wires may result in serious damage.
Before applying power, check that the power supply and ground terminals are connected correctly and input/output devices
are wired properly.
Dielectric withstand voltage test and insulation resistance test

The dielectric withstand voltage and insulation resistance test of the PLC should be measured in accordance with the
following procedure.
1. Remove all input/output wires and power supply wires from the PLC.
2. Connect a crossing wire to each of the PLC terminals (power supply terminal, input terminals and output terminals)
except the ground terminal. For the dielectric withstand voltage test of each terminal, refer to the generic specifications
for the product (refer to Page 17 Generic Specifications).
3. Measure the dielectric withstand voltage and insulation resistance between each terminal and the ground terminal.
• Dielectric withstand voltage 1.5 kV AC or 500 V AC for 1 min (The terminals vary in dielectric withstand voltage.)
• Insulation resistance 10 M or higher by 500 V DC insulation resistance tester
110 7.1 Preparation for Operation
Procedure until operation

The procedure until operation is explained below.
1. Turn on the power of the system.

Check the following items before turning on the power of the system. When the CPU module with the factory default setting is
powered on, the ERR LED flashes because the module has no programs.
• The power supply is wired properly.
• The power supply voltage is within the specified range.
• The CPU module is in the stopped status.
2. Connection with a personal computer

Connect the CPU module with a personal computer on which an engineering tool has been installed.
(Page 112 Connection with a personal computer)
3. Format CPU built-in memory.

Format the CPU built-in memory using the engineering tool.
(GX Works3 Operating Manual)
4. Parameter setting
Set the parameters needed for startup.
(MELSEC iQ-F FX5 User's Manual (Application))
• System parameters 7
• CPU parameters
• Unit parameters
5. Programming
Create a program using the engineering tool. (MELSEC iQ-F FX5 User's Manual (Application))
6. Write the parameters and the program.

Write the parameters and the program set with the engineering tool into the CPU module.
7. Reboot the system.

Reboot the system by any of the following methods.
• Turning off and on the power
• Resetting the CPU module (Page 114 Resetting method)
8. Check errors.
Check the ERR LED of the CPU module. If an error has occurred, check the contents of the error with Module Diagnostics
(CPU Diagnostics) of the engineering tool and eliminate its cause.
9. Run the program.

Set the CPU module to the RUN status and make sure that the P.RUN LED of the CPU module lights up.
7.1 Preparation for Operation 111
Connection with a personal computer

Connect the CPU module with a personal computer on which an engineering tool has been installed.
The system configuration examples and GX Works3 settings are described below.
Direct connection
Setting examples for accessing the CPU module that is directly connected with a personal computer are shown below.
■Ethernet connection
• CPU Module Direct Coupled Setting
Built-in
Ethernet port Ethernet
1) Ethernet cable 2)
GX Works3 settings
No. Item Selection item Internal setting Input value
1) PC side I/F Ethernet Board  
2) PLC side I/F PLC Module Ethernet Port Direct
Connection
Other Station Setting No Specification Check at Communication 30 seconds
Time
Retry Times 0 times
For the FX5 CPU module, the Ethernet adapter on the personal computer side used for the Ethernet port
direct connection can be specified.
Click the [CPU Module Direct Coupled Setting] button on the "Specify Connection Destination Connection"
window to display the "CPU Module Direct Coupled Setting" window. Select the adapter on the window.
• Connection via HUB

Built-in Ethernet
(192.168.0.2)
HUB
2)
1)
GX Works3 settings
1) PC side I/F Ethernet Board  
2) PLC side I/F PLC Module Connection via HUB IP Address 192.168.0.2
Response Wait Time 2 seconds
Other Station Setting No Specification Check at Communication Time 30 seconds
Retry Times 0 times
112 7.1 Preparation for Operation
■Serial connection
FX5-232ADP FX5-232-BD
COM port COM port

(COM1) (COM1)
1) RS-232 cable 2) 1) RS-232 cable 2)

(FX-232CAB-1) (FX-232CAB-1)
GX Works3 settings
1) PC side I/F Serial/USB RS-232C 
COM Port COM1
Transmission Speed 115.2Kbps
2) PLC side I/F PLC Module PLC Mode FX5CPU
Other Station Setting No Specification Check at Communication 30 seconds
Time
Retry Times 0 times
7.2 Operation and Test

Self-diagnostic function
When the power of the CPU module is turned on, the self-diagnostic function to check for errors starts in the module. The 7
CPU module boots when there is no error with the hardware, parameters and program.
When there are no errors, the module enters the RUN status (the P.RUN LED turns on) in response to the RUN instruction
(Page 114 Running, Stopping, and Resetting). If any error is detected, the "ERR" LED flashes or lights up.
Monitoring and debugging

The ON/OFF status of PLC's devices, current values or set values can be monitored or changed by using engineering tools.
7.2 Operation and Test 113
7.3 Running, Stopping, and Resetting

Methods of running, stopping, and resetting
The following two methods of running, stopping, and resetting the FX5U CPU modules are provided.
Using the RUN/STOP/RESET switch

The operation status of the CPU module can be changed with the RUN/STOP/RESET switch.
Setting the RUN/STOP/RESET switch to the RUN position runs the program. Setting the switch to the STOP position stops
the program.
■Resetting method
Resetting can be performed with the RUN/STOP/RESET switch. Resetting is not performed immediately after the RUN/
STOP/RESET switch is set to the RESET position.
Perform the following procedure to reset with the RUN/STOP/RESET switch.
1. Set the RUN/STOP/RESET switch (1) to the RESET position for at least
one second.
2. Make sure that the ERR LED (2) flashes several times and the light goes
off.
3. Return the RUN/STOP/RESET switch to the STOP position.
(2)
(1)
Remote operation
The operation status of the CPU module can be changed externally with the RUN/STOP/RESET switch set to the RUN
position. The operation status of the CPU module can be set to the PAUSE status.
Remote operation can be performed by either of the following methods.
• Using contacts (MELSEC iQ-F FX5 User's Manual (Application))
• Using engineering tools (GX Works3 Operating Manual)
• Using external devices using SLMP (MELSEC iQ-F FX5 User's Manual (SLMP))
Use of several running/stopping methods

■When the RUN/STOP/RESET switch and RUN contact are used
• The RUN/STOP status of the PLC is determined by the conditions shown in the following table.
RUN/STOP/RESET switch status Condition of the input specified as the CPU module status
RUN terminal by parameters
RUN RUN RUN
STOP STOP
STOP RUN STOP
STOP STOP
114 7.3 Running, Stopping, and Resetting
8 MAINTENANCE AND INSPECTION

To keep using the PLC in the optimal condition, perform the following inspections daily or periodically.
8.1 Daily Inspection

Perform the following inspections on a daily basis.
Item Inspection item Description
1 Installation status Looseness of mounting screws Retighten the mounting screws.
of the module
Mounting status of the module The module should be securely mounted.
Looseness of cover The cover should not be off.
2 Connection status Looseness of terminal screws Retighten the terminal screws.
Proximity of crimp terminals Check the proximity between crimp terminals and correct the clearance.
Looseness of connectors Connect cable connectors securely.
3 LED status Check that the LED status is normal.
Page 120 Checking with LEDs
User's manuals for each module
8.2 Periodic Inspection

Perform the following inspections once or twice every 6 months to a year.
Also perform the inspections when facilities have been relocated or modified or when wiring has been changed.
Item Inspection item Description
1 Ambient Operating ambient temperature The temperature in the panel should be 0 to 55 (32 to 131).
8
environment
Operating ambient humidity The humidity in the panel should be 5 to 95%RH.
Working atmosphere Free from corrosive or flammable gas and excessive conductive dust
2 Power supply voltage Voltage within the specified range should be supplied.
3 Installation status Looseness, rattling Retighten mounting screws.
Dirt, foreign matter Wipe away any dirt or foreign matter. Clean the module.
4 Connection status Looseness of terminal screws Retighten the terminal screws.
Proximity of crimp terminals Check the proximity between crimp terminals and correct the clearance.
Looseness of connectors Connect cable connectors securely.
5 Battery BAT LED The BAT LED should be turned off.
When the BAT LED lights up, replace the battery with new one.
Period following the battery Replace the battery with new one if 5 years or more have passed since the battery was
purchase purchased.
OFF status of SM51 (SM8005), SM51 (SM8005) and SM52 (SM8006) should be off.
SM52 (SM8006) If SM51 (SM8005) and SM52 (SM8006) are on, replace the battery with new one.
6 Module Diagnostics (CPU Diagnostics) The normal status of the system should be checked with the Module Diagnostics (CPU
Diagnostics).
Page 122 Module diagnostics (CPU Diagnostics)
7 Relay contacts Check the product life of relay outputs.
Page 89 Product life of relay output contacts
The product life of relay contacts varies considerably depending on the load type used. Note that loads
generating reverse electromotive force or rush current may cause poor contact or welding of contacts which
may lead to considerable reduction of the contact product life.
Page 89 Product life of relay output contacts

8.1 Daily Inspection 115
8.3 Battery
Part names
The Latch device memory and clock data upon power interruption. The battery is not incorporated in the CPU module during
shipment from the factory. Order it if necessary. Parameter setting is required to back up the device memory and clock data.
(Page 117 Setting an optional battery using the engineering tool)
External appearance No. Name Description
(1) Connector Connected to the battery connector of the CPU module.
(2) Nameplate Displays the model name and lot number.
(2) FX3U-32BL
LOT.14X
…………
(1)
Specifications
The following shows functional specifications of the battery.
Item FX3U-32BL
Battery type Lithium manganese dioxide battery
Nominal voltage 3.0 V
Life Standard life: 5 years (at ambient temperature of 25 (77))*1
*1 The life of the battery changes with respect to ambient temperature. (Page 118 Battery life and replacement guidelines)
Battery attachment
The battery is not incorporated in the CPU module during shipment from the factory. To use the battery, attach it following the
procedure below. Parameter setting is required to back up the device memory and clock data using the battery. (Page 117
Setting an optional battery using the engineering tool)
Attachment procedure
1. Turn the power supply off.
2. Remove the expansion board connector cover (A in figure below). If an expansion board is installed, remove it.
A
5
2

116 8.3 Battery
3. Insert the battery connector (B in the figure below) of the battery.
4. Set the battery inside the lower hook (C in the following figure), push up the upper hook (D in the following figure), and
then fit the battery in the battery holder (E in the following figure).
The following figure shows the position of the battery.
D E
B C
5. Attach the expansion board connector cover. If an expansion board was removed in step 2, reinstall it.
Setting an optional battery using the engineering tool

The following setting is required when the capacity of the latch device/latch label is increased using the optional battery.
Note that the battery does not back up the data if the following setting is not provided.
Select the Navigation window  [Parameter]  [FX5UCPU]  [CPU Parameter]  [Memory/Device Setting]  [Device/
Label Memory Area Setting]  [Option Battery Setting]  [Mounted]
8

8.3 Battery 117
Battery replacement
Battery life and replacement guidelines

When the battery voltage is low, the BAT LED is lit red while the power is on, and SM51 (SM8005) and SM52 (SM8006) are
turned ON. The memory can be retained for about one month after the LED is turned on. However, the drop in battery voltage
may not be detected immediately. Prepare a new battery and replace the battery with the new one promptly.
Standard life of FX3U-32BL: 5 years (at ambient temperature of 25 (77))

The life of the battery changes with respect to ambient temperature.
When planning for battery replacement, please estimate the battery life according to the graph below and
order replacement batteries in advance.
Battery life vs. temperature
6
Battery Life [Years]
0
0 10 20 30 40 50
Ambient temperature [Degrees]
Replacement procedure
If the battery voltage is reduced, replace it following the procedure below.
Even with the battery removed, the built-in capacitor holds the data of the memory for the power interruption time (20 sec.).
Battery replacement steps 3 and 4 must be completed within 20 seconds. If the time taken for battery replacement is longer
than the power interruption time, the data of the memory may be lost.
1. Turn the power supply off.
2. Remove the expansion board connector cover (A in figure below). If an expansion board is installed, remove it.
A
5
2

118 8.3 Battery
3. Extract the old battery from the battery holder ("B" in figure below), and disconnect the battery connector ("C" in figure
below).
C
4. Install the new battery. (Page 116 Battery attachment)
5. Attach the expansion board connector cover. If an expansion board was removed in step 2, reinstall it.
• After replacing the battery, check whether the devices set by the latch and clock data are backed up
correctly, confirm safety, and then run the PLC.
• If the devices set by the latch are not backed up correctly, clear them, and set their initial values and clock
data again if necessary.
Reading the date of manufacture

How to read the battery lot number
Nameplate
Connector
8
Type FX3U-32BL
LOT.14X
…………
LOT
1 4 X
Month (Example: October):

1 to 9 = January to September,
X = October, Y = November, Z = December
Year (Example: 2014): Last two digits of year
Special relay for low battery voltage

Prepare a system which allows constant external monitoring of the battery status, using a GOT, etc.
• SM52 (SM8005)
The special relay turns ON when the battery voltage is the specified value or less.
The special relay turns OFF when the battery voltage is normal.
SM52(SM8005)
Y1 Y1 is output when a battery low-voltage condition occurs.
Battery low-voltage
• SM51 (SM8006)
The special relay turns ON when the battery voltage is the specified value or less.
The special relay stays ON even when the battery voltage is normal.
• SD8005
Battery voltage can be monitored.

8.3 Battery 119
9 TROUBLESHOOTING
Details on errors occurring in the system, their causes, and corrective actions are explained below.
For details on troubleshooting for each module, refer to the manuals for the module.
Saving the programs and devices used at the occurrence of an error helps in identifying the cause of the error.
(Page 124 Backing Up the Data)
9.1 Troubleshooting Procedure

If an error occurs, perform troubleshooting in the following order.
1. Check that each module is properly mounted and wired.
2. Check the LEDs of the CPU module. (Page 120 Checking with LEDs)
3. Check the LEDs of each intelligent function module. (Manuals for each module)
4. Connect the engineering tool and execute the Module Diagnostics (CPU Diagnostics). The error cause and the action to
be taken can be displayed. (Page 122 Module diagnostics (CPU Diagnostics))
5. Check the cause of the error and take corrective actions.
9.2 Checking with LEDs

Check the module status with LEDs as a means to perform the primary diagnosis.
Checking the PWR LED

If the PWR LED is turned off, check the following items.
Item to check Cause and action
Measure the voltage supply to the CPU module. If the power source is not supplying the proper voltage, provide a power source that does.
Remove extension modules and all wiring other than the If the PWR LED turns on in this condition, the service power supply may be shorted or
one for the power supply, and turn on the power supply. overloaded. Reconnect the modules and wire one by one to identify the cause.
If the PWR LED still does not turn on even after the items shown above are checked, there may be a hardware issue.
Consult your local Mitsubishi Electric representative.
Checking the BAT LED

If the BAT LED is turned on, check the following items.
The LED is valid when the optional battery is installed and the LED is set to "display" for battery errors by using the parameter.
Check the installation of the battery. Install the battery properly.
Check the battery voltage. If the battery voltage is reduced, replace the battery with a new one.
Battery voltage can be monitored with PLC data register SD8005.
(Page 116 Battery)
9 TROUBLESHOOTING
120 9.1 Troubleshooting Procedure
Checking the ERR LED

9
If the ERR LED flashes
If the ERR LED is turned on, check the following items.
Write system parameters, CPU parameters, and Programs or parameters are not written or damaged. Since a CPU module with the factory default
program files. Then power on the CPU module setting has no programs, the ERR LED flashes.
again.
If the ERR LED is turned on

If the ERR LED is turned on, check the following items.
Set the CPU module to the STOP status and turn on When the ERR LED turns off, a watchdog timer error has probably occurred. Take any of the following
the power supply again. measures.
• Review the program and avoid the maximum value (SD524, SD525) of the scan time exceeding the
the scan time monitoring time setting value set by the parameter.
• Check that the input used for input interruption or pulse catch is not being abnormally turned on and
off in one scan.
• Check that the frequency of the pulse input to the high-speed counter is within the specified range.
• Add some WDT instructions to the program and reset the watchdog timer several times in one scan.
Provide a different power supply to the CPU module. If the ERR LED turns off, noise may have affected the module. Consider taking the following measures.
• Check the ground wiring, and reexamine the wiring route and installation location.
• Fit a noise filter onto the power supply line.
If the ERR LED still does not turn off even after the items shown above are checked, there may be a hardware issue.
Checking the P.RUN LED

If the P.RUN LED is turned off, check the status of the ERR LED and take corrective actions. (Page 121 Checking the
ERR LED)
9.3 Troubleshooting using the engineering tool

Check the error or history using the engineering tool, and identify the error cause. More detailed information on the error as
well as the error cause and action to be taken can be checked by using the engineering tool.
The engineering tool has the following functions for troubleshooting.
Function Description
Module diagnostics (CPU Diagnostics) This function diagnoses the module. (The current error and its details can be checked.)
For details on each function, refer to the following.

GX Works3 Operating Manual
9 TROUBLESHOOTING
9.3 Troubleshooting using the engineering tool 121
Module diagnostics (CPU Diagnostics)

This function diagnoses CPU module, expansion adapter, and expansion board. (The current error and its details can be
checked.)
Information required for troubleshooting, such as the current error, details and cause of the error, and action to be taken, are
displayed. The incorrect parameter setting and program error location can also be identified by selecting the error and clicking
the [Error Jump] button. On the [Module Information List] tab, the LED status and the switch status of the target module can
be checked.
[Diagnostics][Module diagnostics(CPU Diagnostics)]
9 TROUBLESHOOTING
122 9.3 Troubleshooting using the engineering tool
9.4 Error Status and Operations on Occurrence of an

Error 9
When an error occurs, the CPU module performs preconfigured actions depending on the status of the error.
Error status
Errors are classified into the following three types according to the urgency of the errors.
Error Program Description Required action
status execution status
Major error Stop The module is unable to continue its operation due to a Perform troubleshooting. If the error still persists,
hardware issue. consult your local Mitsubishi Electric representative.
Moderate Stop The module is unable to carry out programs or continue the To resume the execution of the program or the data
error data communication with stations on the network due to communication with the stations on the network, use
improper program or parameter settings and temporary noise. the engineering tool to identify the cause of the error
and take corrective actions.
Minor error Continue The module has detected a minor error or alarm. However, the Check the details on the error with the engineering
execution of the program and the data communication with the tool. If necessary, take corrective actions for the error.
stations on the network continues.
Operation at the occurrence of an error

Errors are classified into stop errors and continuable errors.
■Stop error
When a stop error occurs, the CPU module stops operation and enters the STOP status. External outputs of the module follow
the "STOPRUN output mode" settings of parameters.
For details on parameters, refer to MELSEC iQ-F FX5 User's Manual (Application).
■Continuable error
When a continuable error occurs, the CPU module will keep the operation status and carry out operations.
Only continuable errors can be canceled. When a continuable error is canceled and the CPU module is restored, the CPU
module returns to the status before the occurrence of the error. Continuable errors can be canceled by either of the following
methods.
• Using engineering tools
• Using special relay (SM) (Page 124 Canceling Errors)
Operation settings of the CPU module on occurrence of an intelligent function module error
The operation of the CPU module on occurrence of an intelligent function module error can be set with the engineering tool.
Configure the settings with [I/O Assignment Settings] in the system parameters.
9 TROUBLESHOOTING
9.4 Error Status and Operations on Occurrence of an Error 123
9.5 Backing Up the Data

Saving the following information immediately after the occurrence of an error helps in analyzing the cause of the error.
• Parameters, programs, and device memory
• Error histories
Backing up parameters, programs, and device memory

The procedure for backing up parameters, programs, and device memory using the engineering tool is explained below.
[Online][Read from PLC]
1. Check the parameters, programs, and device memory to back up.
2. Click the [Execute] button to read the data.
Backing up devices and buffer memory

The procedure for backing up devices and buffer memory using the engineering tool is explained below.
[Online][Read from PLC]
1. Click the "Device Memory" check box.
2. Click [Detail].
3. Input character strings in "Device Data Name" and select the devices to back up.
4. Select the "Buffer Memory Intelligent Module No.", and input module number.
5. Click [OK] and then click [Execute] to read the data from the PLC.
9.6 Canceling Errors

Only continuable errors can be canceled.
If an error is canceled and the CPU module is restored, the status of SM, SD, or LEDs returns to the status before the
occurrence of the error. After an error is canceled and when the same error occurs again, this error is recorded again in the
error history.
When all errors are cancelled at once, annunciators will also be cleared. To clear annunciators individually, use the RST
instruction.
Continuable errors can be canceled by the following method.
Using special relays (SM)

Turning on and off SM50, all errors will be canceled.
9 TROUBLESHOOTING
124 9.5 Backing Up the Data
9.7 Troubleshooting for Each Symptom

When the CPU module does not operate properly, check the appropriate item from the following and perform troubleshooting.
9
I/O operation (CPU module, I/O module)
Output does not turn on

Item to check Action
Check for errors with external wiring. Connect the external wiring properly.
Stop the PLC, and forcibly turn on or off the inoperable output with a ■When the output operates
peripheral device or the engineering tool. The output may be turned off unintentionally in the program. Review user
program (Duplicate coils or RST instructions).
■When the output does not operate
Check the configuration of the connected devices and the connection of the
extension cables.
If the configuration of the external wiring and connected devices and the
connection of the extension cables are acceptable, there may be a hardware
issue. Consult your local Mitsubishi Electric representative.
Output does not turn off

Check for errors with external wiring. Connect the external wiring properly.
Stop the PLC and check that the output turns off. ■When the output turns off
The output may be turned off unintentionally in the program. Review user
program (Duplicate coils or RST instructions).
■When the output does not turn off
There may be a hardware fault. Consult your local Mitsubishi Electric
representative.
Input does not turn on

Disconnect the external wiring and connect the [S/S] terminal and the [0V] ■When the input turns on
terminal or the [24V] terminal. Check that the input device does not have a built-in diode or parallel
Short-circuit the [0V] terminal or [24V] terminal not connected to the [S/S] resistance.
terminal and the input terminal, and check the LED or a peripheral device to If so, refer to Page 85 Precautions for connecting input devices.
check that the input turns on. ■When the input does not turn on
Measure the voltage between the [0V] terminal or [24] V terminal not
connected to the [S/S] terminal and the input terminal with a tester to check
that the voltage is 24 V DC.
Check the configuration of the external wiring and connected devices and the
connection of the extension cables.
Input does not turn off

Check that there is no leakage current from input devices. If the leakage current is 1.5 mA or more, connect a bleeder resistance.
(Page 85 Precautions for connecting input devices)
9 TROUBLESHOOTING
9.7 Troubleshooting for Each Symptom 125
PLC write, PLC read
PLC write cannot be performed

If data cannot be written to the CPU module from the engineering tool, check the following items.
Check if a password is not registered. When a password has been registered, authenticate the password with
the engineering tool.
When a SD memory card is the write destination, check that the write protection is Remove the write protection from the SD memory card.
not applied to the card. Page 141 SD Memory Card
When a SD memory card is the write destination, check that the card is formatted. Format the SD memory card.
Check that the size of the write data does not exceed the memory capacity. • Ensure sufficient empty capacity.
• Clear the memory to which the data is to be written.
If writing still cannot be performed even after the items shown above are checked, there may be a hardware issue. Consult
your local Mitsubishi Electric representative.
PLC read cannot be performed

If data cannot be read from the CPU module to the engineering tool, check the specification of the target memory to be read.
Check the memory and reset the CPU module again. Then try PLC read again.
If reading still cannot be performed, there may be a hardware issue. Consult your local Mitsubishi Electric representative.
The program is unintentionally overwritten

The boot operation may be being performed. Read the parameters and review the boot file settings with the engineering tool.
If the boot operation is not being performed, there may be a hardware issue. Consult your local Mitsubishi Electric
representative.
For details on the boot operation, refer to MELSEC iQ-F FX5 User's Manual (Application).
Boot operation
Boot operation cannot be performed from the SD memory card

Checking item Action
Check for errors in the CPU module. Remove the cause of the error.
Check that the file is set in the boot file settings of the parameters. Set the file in the parameters.
Check that the file is set in the program file settings of the parameters.
Check that the file to run is stored in the SD memory card. Store the file to run.
If the boot operation cannot be performed even after the items shown above are checked, there may be a hardware issue.
9 TROUBLESHOOTING
126 9.7 Troubleshooting for Each Symptom
APPENDIX A
Appendix 1 How to Check the Date of Manufacture
Check the date of manufacture of the product (except the expansion board) as follows.
• Nameplate
• Module front surface (CPU module only)
Checking the nameplate

The date of manufacture of the product can be checked from the manufacturer's serial number "S/N" indicated on the
nameplate of the product. (For details of the battery, refer to Page 119 Reading the date of manufacture)
Ex.
Example nameplate
CPU module (manufacturer's serial number: 1490001)
Right side
* Actual product nameplate differs

from the example shown above.
1 4 X 0 0 0 1
Control number
Check on the module front surface

The year and month of production of the product can be checked from the manufacturer's serial number LOT on the front (at
the bottom) of the CPU module.
LOT 14X
1 4 X

APPENDIX
Appendix 1 How to Check the Date of Manufacture 127
Appendix 2 Standards
Certification of UL, cUL standards
FX5 supports UL(UL, cUL) standards.
For models that support UL standards, refer to the following.
UL site http://site.ul.com
UL, cUL file number: E95239
Compliance with EC directive (CE Marking)

This note does not guarantee that an entire machine produced in accordance with the contents of this note will comply with
the following standards.
Compliance to EMC directive and LVD directive of the entire mechanical module should be checked by the user/
manufacturer. For more details please contact to the local Mitsubishi Electric sales site.
Requirement for compliance with EMC directive

The following products have shown compliance through direct testing (of the identified standards below) and design analysis
(through the creation of a technical construction file) to the European Directive for Electromagnetic Compatibility (2004/108/
EC) when used as directed by the appropriate documentation.
Caution
• This product is designed for use in general industrial applications.
Note
• The manufacturer, manufacturing location, and authorized representative in EU are as follows.
Manufacturer: Mitsubishi Electric Corporation
Address: 2-7-3 Marunouchi, Chiyoda-ku, Tokyo, 100-8310 Japan
Manufacturing location: Mitsubishi Electric Corporation Himeji Works

Address: 840 Chiyoda-machi, Himeji, Hyogo, 670-8677 Japan
Authorized representative in EU: Mitsubishi Electric Europe B.V.

Address: Gothaer Str. 8, 40880 Ratingen, Germany
APPENDIX
128 Appendix 2 Standards
Product compatibility
Type: Programmable controller (open type equipment)
A
Models: FX5 manufactured
from October 1st, 2014 FX5U-32MR/ES FX5U-32MT/ES FX5U-32MT/ESS
FX5U-64MR/ES FX5U-64MT/ES FX5U-64MT/ESS
FX5-8EX/ES FX5-8EYR/ES FX5-8EYT/ES FX5-8EYT/ESS
FX5-16EX/ES FX5-16EYR/ES FX5-16EYT/ES FX5-16EYT/ESS
FX5-32ER/ES FX5-32ET/ES FX5-32ET/ESS
FX5-232ADP FX5-485ADP FX5-232-BD FX5-485-BD FX5-422-BD-GOT
FX5-1PSU-5V FX5-CNV-BUS
from January 1st, 2015 FX5-4AD-ADP FX5-4DA-ADP
Electromagnetic compatibility (EMC) directive Remarks

EN61131-2:2007 Programmable controllers Compliance with all relevant aspects of the standard.
- Equipment requirements and tests EMI
• Radiated emission
• Conducted emission
EMS
• Radiated electromagnetic field
• Fast transient burst
• Electrostatic discharge
• High-energy surge
• Voltage drops and interruptions
• Conducted RF
• Power frequency magnetic field
Requirement for compliance with LVD directive

The following products have shown compliance through direct testing (of the identified standards below) and design analysis
(through the creation of a technical construction file) to the European Directive for Low Voltage (2006/95/EC) when used as
directed by the appropriate documentation.
Type: Programmable controller (open type equipment)
Models: FX5 manufactured
from October 1st, 2014 FX5U-32MR/ES FX5U-32MT/ES FX5U-32MT/ESS
FX5-8EYR/ES FX5-16EYR/ES
FX5-32ER/ES FX5-32ET/ES FX5-32ET/ESS
FX5-1PSU-5V
Electromagnetic compatibility (EMC) directive Remarks

EN61131-2:2007 Programmable controllers The equipment has been assessed as a component for fitting in a suitable
- Equipment requirements and tests enclosure which meets the requirements of EN61131-2:2007.
Caution for compliance with EC Directive
Installation in enclosure
FX5U CPU modules are open-type devices that must be installed and used within shielded conductive control boxes.
Please use the PLCs while installed in conductive shielded control boxes. Please secure the control box lid to the control box
(for conduction). Installation within a control box greatly improves the safety of the system and aids in shielding noise from the
PLC.
APPENDIX
Appendix 2 Standards 129
Caution for when analog products are used

It is recommended to perform the following when precision of measuring and control is required.
As analog devices are sensitive by nature, their use should be considered carefully. For users of proprietary cables (integral
with sensors or actuators), these users should follow those manufacturers' installation requirements.
Mitsubishi Electric recommends that shielded cables be used. If no other EMC protection is provided, users may experience
temporary loss of accuracy between +10%/-10% in very heavy industrial areas.
However, Mitsubishi Electric suggests that if adequate EMC precautions are followed with general good EMC practice for the
user's complete control system, users should expect normal errors as specified in this manual.
• Sensitive analog cables should not be laid in the same trunking or cable conduit as high voltage cabling. Where possible,
users should run analog cables separately.
• Good cable shielding should be used. When terminating the shield at Earth - ensure that no earth loops are accidentally
created.
• When reading analog values, EMC induced errors can be smoothed out by averaging the readings. This can be achieved
either through functions on the analog devices or through a user's program in the FX5U CPU module.
Perform the following when using the analog expansion adapter:
• Installation in Enclosure
Programmable controllers are open-type devices that must be installed and used within conductive control cabinets.
Please use the programmable controller while installed within a conductive shielded control cabinet. Installation within a
control cabinet greatly affects the safety of the system and aids in shielding noise from the programmable controller.
• Control cabinet
- The control cabinet must be conductive.
- Ground the control cabinet with the thickest possible grounding cable.
- To ensure that there is electric contact between the control cabinet and its door, connect the cabinet and its doors with
thick wires.
- In order to suppress the leakage of radio waves, the control cabinet structure must have minimal openings. Also, wrap
the cable holes with a shielding cover or other shielding devices.
- The gap between the control cabinet and its door must be as small as possible by attaching EMI gaskets between them.
Shielding cover
Shielded cable
EMI gasket
Wires*1
*1 These wires are used to improve the conductivity between the door and control cabinet.
• Cables
- Make sure to use shielded cables as cables pulled out of the control cabinet.
- Connect the shield such as shielded cables and shielding covers to the grounded control cabinet.
• It is possible that the accuracy temporarily fluctuates within 10 %.
Perform the following when using the FX5-4AD-ADP:
• Set the number of times of winding to “2 turns” within approximately 200 mm (7.87") from terminal block of the analog cable
on the FX5-4AD-ADP side, and attach a ferrite core. (Ferrite core used in our test: E04SR401938 manufactured by SEIWA
ELECTRIC MFG. CO., LTD.)
Perform the following when using the FX5-4DA-ADP:
• Set the number of times of winding to “2 turns” within approximately 200 mm (7.87") from the connectors of the power cable
on the FX5-4DA-ADP side, and attach a ferrite core. (Ferrite core used in our test: E04SR401938 manufactured by SEIWA
ELECTRIC MFG. CO., LTD.)
• The FX5-4DA-ADP requires that the cable used for power supply is 30 m (9'85") or less.
APPENDIX
130 Appendix 2 Standards
Caution for when the built-in Ethernet port is used

• Use a shielded twisted pair cable for the 10BASE-T or 100BASE-TX cable. Strip a part of the jacket of the shielded twisted
A
pair cable as shown below and ground as much of the exposed shield as possible to both sides of the cable.
• Connect a ferrite core to both ends of the cable. (Ferrite core used in tests by Mitsubishi: ZCAT2035-0930A manufactured
by TDK Co.)
Shield
Clamp metal fitting

Ferrite core
APPENDIX
Appendix 2 Standards 131
Appendix 3 I/O Module

Product configuration
There are various types of I/O module. They differ in supply voltage, number of input/output points, input form, output form
and connection type.
I/O module
Number of
Power supply input/output points Input type Output type Connection form
PLC internal 8 24 V DC Relay Terminal block

power (sink/source)
16 Transistor (sink)
100 to 240 V
AC 32 Transistor (source)
Product list
Input modules
Sink : Sink, Source : Source
Model Input Output Connection
Type No. of points Common wiring Type No. of points Common wiring type
system system
■Input extension/sink and source input type
FX5-8EX/ES 24 V DC 8 Sink Source    Terminal block
FX5-16EX/ES 24 V DC 16 Sink Source    Terminal block
Output module
system system
■Output extension/relay output type
FX5-8EYR/ES    Relay 8  Terminal block
FX5-16EYR/ES    Relay 16  Terminal block
■Output extension/sink output only
FX5-8EYT/ES    Transistor 8 Sink Terminal block
FX5-16EYT/ES    Transistor 16 Sink Terminal block
■Output extension/source output only
FX5-8EYT/ESS    Transistor 8 Source Terminal block
FX5-16EYT/ESS    Transistor 16 Source Terminal block
APPENDIX
132 Appendix 3 I/O Module

A
system system
■Input/output extension/sink and source input/relay output type
FX5-32ER/ES 24 V DC 16 Sink Source Relay 16  Terminal block
■Input/output extension/sink and source input/sink output only
FX5-32ET/ES 24 V DC 16 Sink Source Transistor 16 Sink Terminal block
■Input/output extension/sink and source input/source output only
FX5-32ET/ESS 24 V DC 16 Sink Source Transistor 16 Source Terminal block
Specifications
The generic specifications are the same as those for the CPU module. (Page 17 Generic Specifications)
Power supply specifications

■Input modules
Item Specifications
Voltage rating 24 V DC (supplied from service power supply or external power supply)
5 V DC (supplied from PLC)
Current consumption (5 V DC) FX5-8EX/ES 75 mA
FX5-16EX/ES 100 mA
Current consumption (24 V DC) FX5-8EX/ES 50 mA
FX5-16EX/ES 85 mA
■Output modules
Item Specifications
Voltage rating 24 V DC (supplied from PLC)
5 V DC (supplied from PLC)
Current consumption (5 V DC) FX5-8EY 75 mA
FX5-16EY 100 mA
Current consumption (24 V DC) FX5-8EY 75 mA
FX5-16EY 125 mA
■Powered input/output module(FX5-32E)

Item Specifications
Voltage rating 100 to 240 V AC
Allowable supply voltage range 85 to 264 V AC
Rated frequency 50/60 Hz
Allowable instantaneous power failure time Operation can be continued upon occurrence of instantaneous power failure for 10 ms or less.
Power fuse 250 V, 3.15 A time-lag fuse
Rush current 30 A max. 5 ms or less/100 V AC
65 A max. 5 ms or less/200 V AC
Power consumption*1 25 W
24 V DC service power supply*2 250 mA (Supply capacity when service power supply is used for input circuit of the powered input/
output module)
310 mA (Supply capacity when external power supply is used for input circuit of the powered input/
output module)
*1 This item shows value when all 24 V DC service power supplies are used in the maximum configuration connectable to the CPU
module. (The current of the input circuit is included.)
*2 When I/O modules are connected, they consume current from the 24 V DC service power. For details on the service power supply, refer
to Page 48 Limitation on Current Consumption.
APPENDIX
Appendix 3 I/O Module 133
External color, weight, accessories

■Input module/output module
Item Specifications
External color Munsell 0.6B7.6/0.2
Mass (weight) FX5-8E Approx. 0.2 kg (0.44 lbs)
FX5-16E Approx. 0.25 kg (0.55 lbs)
Accessories Dust proof protection sheet
■Powered input/output module (FX5-32E)

Item Specifications
External color Munsell 0.6B7.6/0.2
Mass (weight) Approx. 0.65 kg (1.43 lbs)
Accessories Extension cable, dust proof protection sheet
APPENDIX
Input specifications
There is the simultaneous ON ratio of available PLC inputs or outputs with respect to the ambient temperature.
A
For details, refer to Page 22 Input/Output Derating Curve
Item Specifications
No. of input points FX5-8EX/ES 8 points
FX5-16EX/ES 16 points
FX5-32E 16 points
Connection type Terminal block (M3 screws)
Input type Sink/source
Input signal voltage 24 V DC +20%, -15%
Input signal current 4 mA/24 V DC
Input impedance 5.6 k
Input sensitivity current ON 3.0 mA or more
OFF 1.5 mA or less
Input response time ON: 50 s or less
OFF: 150 s or less
Input signal format No-voltage contact input
Sink: NPN open collector transistor
Source: PNP open collector transistor
Input circuit insulation Photo-coupler insulation
Indication of input operation LED is lit when input is on
Input circuit configuration • When using service power supply by input module
S/S S/S
0V 0V
24V 24V
Input module Input module

S/S S/S
X X
5.6 k 5.6 k
• When using service power supply by powered input/output module

Powered input/output module Powered input/output module

Fuse Fuse
L L
N N
100 to 240 V AC 100 to 240 V AC
24V 24V
0V 0V
S/S S/S
X X
5.6 k 5.6 k
APPENDIX
Item Specifications
Input circuit configuration • When using external power supply by input module
S/S S/S
0V 0V
24V 24V
Input module Input module

S/S S/S
X X
5.6 k 5.6 k
• When using external power supply by powered input/output module

Powered input/output module Powered input/output module

Fuse Fuse
L L
N N
100 to 240 V AC 100 to 240 V AC
24V 24V
0V 0V
S/S S/S
X X
5.6 k 5.6 k
Output specifications
There is the simultaneous ON ratio of available PLC inputs or outputs with respect to the ambient temperature.
For details, refer to Page 22 Input/Output Derating Curve
■Relay output
Item Specifications
No. of output points FX5-8EYR/ES 8 points
FX5-16EYR/ES 16 points
FX5-32ER/ES 16 points
Output type Relay
External power supply 30 V DC or less
240 V AC or less
(250 V AC or less when the module does not comply with CE UL, cUL standards)
Output circuit insulation Mechanical insulation
Max. load 2 A/point
The total load current of resistance loads per common terminal should be the following value.
Open circuit leakage current 
Min. load 5 V DC, 2 mA (reference values)
Response time OFFON Approx. 10 ms
ONOFF Approx. 10 ms
Load
Y
DC power
supply
COM0
Fuse
AC power
Y
supply
COM1
Fuse
APPENDIX
■Transistor output (sink output)

Item Specifications
No. of output points FX5-8EYT/ES 8 points A
FX5-16EYT/ES 16 points
FX5-32ET/ES 16 points
Output type Transistor/sink output
Output circuit insulation Photo-coupler insulation
Open circuit leakage current 0.1 mA/30 V DC
Min. load 
Response time OFFON 0.2 ms or less/200 mA (at 24 V DC)
ONOFF 0.2 ms or less/200 mA (at 24 V DC)
Voltage drop when ON 1.5 V or less
Load
Y
DC power
supply
COM0
Fuse
Y
DC power
supply
COM1
Fuse
■Transistor output (source output)

Item Specifications
No. of output points FX5-8EYT/ESS 8 points
FX5-16EYT/ESS 16 points
FX5-32ET/ESS 16 points
Output type Transistor/source output
Output circuit insulation Photo-coupler insulation
Open circuit leakage current 0.1 mA/30 V DC
Min. load 
Response time OFFON 0.2 ms or less/200 mA (at 24 V DC)
ONOFF 0.2 ms or less/200 mA (at 24 V DC)
Voltage drop when ON 1.5 V or less
Load
Y
DC power
supply
+V0
Fuse
Y
DC power
supply
+V1
Fuse
APPENDIX
External dimensions and component names
Input module/output module

(mounting hole pitch) Unit: mm (inches)
83 (3.27")
W Without cover 8 (0.32")
[1]
[2]
80 (3.15")
90 (3.55")
[3] [4]
[1]
2-4.5 mounting holes

External dimensions
Model W: mm (inches)
FX5-8EX/ES 40 (1.58")
FX5-8EYR/ES, FX5-8EYT/ES, FX5-8EYT/ESS
FX5-16EX/ES
FX5-16EYR/ES, FX5-16EYT/ES, FX5-16EYT/ESS
Part names
[1] Input display LED, output display LED Lit when input or output is on.
[2] POWER LED Indicates whether the input modules/output modules is powered or not.
Lit: Powered
Off: Not powered or hardware error
[3] Pullout tab They are used when drawing out an extension cable.
[4] Extension connector Connector for connecting the extension cable of an extension module.
APPENDIX

2-4.5 mounting holes A
[2] [3] [4] [5] [6] Unit: mm (inches)
[1]
90 (3.55")
80 (3.15")
140 (5.52") (mounting hole pitch) 8 (0.32")
W 83 (3.27")
[Without cover]
[8] [9] [8]
[7] [10]
[8] [9] [8]

External dimensions
Model W: mm (inches)
FX5-32ER/ES, FX5-32ET/ES, FX5-32ET/ESS 150 (5.91")
Part names
[1] Extension connector cover (for preceding module) Cover for protecting the extension connector cover (for preceding module).
[2] Terminal block cover Cover for protecting the terminal block.
The cover can be opened for wiring. Keep the covers closed while equipment is running
(power is on).
[3] POWER LED Indicates whether the powered input/output module is powered or not.
Lit: Powered
Off: Not powered or hardware error
[4] Input display LED Lit when input is on.
[5] Output display LED Lit when output is on.
[6] Extension connector cover (for next module) Cover for protecting the extension connector cover (for next module).
[7] Extension connector (for preceding module) Connecter for connecting the supplied extension cable that connects to the preceding
module (the CPU module side).
[8] Terminal block mounting screws Gradually loosen the left and right screws (alternatingly) to remove the upper part of the
terminal block.
[9] Terminal Terminals for power, input, and output.
For details on the terminal layout, refer to Page 140 Terminal layout.
[10] Extension connector (for next module) Connector for connecting the extension cable of an extension module.
APPENDIX
Terminal layout
FX5-8EX/ES FX5-8EYR/ES FX5-8EYT/ESS
FX5-8EYT/ES
S C
O
+
V
\
M
X S Y 0 Y 0
0 0 0
1 1 1
2 2 2
3 3 3
C +
O
M V
X Y 1 Y 1
4 4 4
5 5 5
6 6 6
7 7 7
FX5-16EX/ES FX5-16EYR/ES FX5-16EYT/ESS

FX5-16EYT/ES
S C
O
+
V
\
M
S X 0 Y 0 Y
0 0 0
1 1 1
2 2 2
3 3 3
4 Lower 4 Lower 4
Lower
5 numbers 5 numbers 5
numbers
6 6 6
7 7 7
X Y Y
0 0 0
1 1 1
2 2 2
3 Higher 3 Higher 3 Higher
4 number 4 number 4 number
5 5 5
6 6 6
7 7 C 7 +
O
M V
1 1
FX5-32E
S/S 0V X0 2 4 6 X0 2 4 6
L N 24V 1 3 5 7 1 3 5 7
FX5-32ER/ES, FX5-32ET/ES
Y0 2 Y4 6 Y0 2 Y4 6
COM0 1 3 COM1 5 7 COM2 1 3 COM3 5 7
FX5-32ET/ESS
Y0 2 Y4 6 Y0 2 Y4 6
+V0 1 3 +V1 5 7 +V2 1 3 +V3 5 7
APPENDIX
Appendix 4 SD Memory Card

Part names A
An SD memory card is installed in the CPU module to operate the module based on the project data in the card.
(1)

(1) Write protect switch Setting the switch in the lock position prevents the data in the SD memory card from being deleted and overwritten.
Specifications
The following shows functional specifications of the SD memory card.
Item NZ1MEM-2GBSD NZ1MEM-4GBSD
Type SD memory card SDHC memory card
Capacity 2 Gbytes 4 Gbytes
Number of writes 60,000 times 100,000 times
External dimensions Height 32 mm (1.25")
Width 24 mm (0.94")
Depth 2.1 mm (0.08")
Mass (weight) 2g
For L1MEM-2GBSD and L1MEM-4GBSD, refer to the following.

(QCPU User's Manual(Hardware Design, Maintenance and Inspection)
Handling of the SD memory card

• Operational compatibility of the SD memory cards manufactured by Mitsubishi (NZ1MEM-2GBSD and NZ1MEM-4GBSD)
with MELSEC iQ-F series CPU modules has been checked. Use of SD memory card other than a Mitsubishi SD memory
card may result in loss of the data stored in the SD memory card, or problems such as system stop.
• When mounted in the CPU module, SD memory cards manufactured by Mitsubishi are compliant with IEC61131-2.
• The SDHC memory card can be used only with devices with an SDHC logo or whose user's manual lists an SDHC logo.
Note that SDHC cards cannot be used with devices that support only "SD" specifications.
• Turning off or resetting the CPU module or removing the SD memory card while the card is being accessed may corrupt the
data in the SD memory card. Always turn off or reset the CPU module or remove the SD memory card after disabling
access to the SD memory card. With SM606 (SD memory card forced disable instruction) and SM607 (SD memory card
forced disable status flag), the SD memory card can be disabled and its usage status can be checked.
• It is recommended that important data be periodically backed up to CD, DVD, or other media.
Formatting
To use any SD memory card in the CPU module, the card must be formatted. In the initial state after purchase, the SD
memory card is not formatted. Insert the SD memory card to a CPU module and format the SD memory card using the
engineering tool before use. Do not format the SD memory card using the personal computer. (GX Works3 Operating
Manual)
APPENDIX
Appendix 4 SD Memory Card 141
Insertion and removal of the SD memory card

The following explains insertion and removal of the SD memory card.
Insertion procedure
Mount the SD memory card. Pay attention to the direction of the card and follow the procedure below.
1. Insert the SD memory card (1) straight into the SD memory card slot.
Make sure that the notch of the card is directed downward. After
(1) mounting, check that the card is mounted completely. If the card is
mounted incompletely, malfunctions may occur because of poor contact.
2. The CARD LED (2) blinks until the SD memory card becomes available.
3. The CARD LED turns on when the SD memory card is available.
(2)
4. If the CARD LED dose not turn on even though the SD memory card is
mounted, make sure that SM606 (forcibly stop using SD memory card
instruction) and SM607 (forcibly stop using SD memory card flag) are
OFF by using engineering tools.
Removal procedure
1. Press the SD memory card stop switch (1) for one second or more to
stop access to the card. The CARD READY LED (2) blinks during the
(3) access stop operation, and then the LED is turned OFF when the
operation is completed.
2. Insert the SD memory card (3) once, and then pull it straight.
(1)
(2)
Precautions
• When mounting or removing the SD memory card while the power is ON, follow the above-mentioned procedure.
Otherwise, the data in the card may be broken.
• When removing the SD memory card which is being accessed by any function, the CARD LED is turned OFF after the
access is completed. When the CARD LED is turned OFF depends on the accessing function.
• When SM605 (mount and remove memory card disabling flag) is ON, the CARD LED is not turned OFF even if the SD
memory card stop switch is pressed. If the CARD LED is not turned OFF, turn ON SM606 (instruction of forcibly stop using
SD memory card) so that the SD memory card cannot be used.
APPENDIX
142 Appendix 4 SD Memory Card
Appendix 5 Precautions for Battery Transportation

When transporting lithium batteries, follow required transportation regulations. A
Batteries used in the FX5U CPU module are classified as follows.
Control-subject product
Built-in
None (FX5U CPU modules do not include batteries when shipped from the factory.)
Battery only (spare parts and optional parts)

Model Battery type Product form Lithium contained Weight*1
(g/battery) (g/battery)
FX3U-32BL Lithium-metal battery Cell 0.15 30
*1 Weight in packaging.
Precautions for transportation

When transporting the product above, follow IATA Dangerous Goods Regulations, IMDG Code (International Maritime
Dangerous Goods Code), and domestic transportation regulations in each country. For details, contact the transportation
company to be used.
APPENDIX
Appendix 5 Precautions for Battery Transportation 143
Appendix 6 Handling of Batteries and Devices with

Built-in Batteries in EU Member States
This section describes the precautions for disposing of waste batteries in EU member states and exporting batteries and/or
devices with built-in batteries to EU member states.
Disposal precautions
In EU member states, there is a separate collection system for waste batteries.
Dispose of batteries properly at the local community waste collection/recycling center.
The symbol shown in the following figure is printed on the batteries and packaging of batteries and devices with built-in
batteries. This symbol indicates that batteries need to be disposed of separately from other wastes.
This symbol is for EU member states only.

The symbol is specified in the new EU Battery Directive (2006/66/EC) Article 20 "Information for end-users"
and Annex II.
Exportation precautions
The new EU Battery Directive (2006/66/EC) requires the following when marketing or exporting batteries and/or devices with
built-in batteries to EU member states.
• To print the symbol on batteries, devices, or their packaging
• To explain the symbol in the manuals of the products
Labeling
To market or export batteries and/or devices with built-in batteries, which have no symbol, to EU member states, print the
symbol shown in the figure above on the batteries, devices, or their packaging.
Explaining the symbol in the manuals

To export devices incorporating Mitsubishi programmable controller to EU member states, provide the latest manuals that
include the explanation of the symbol. If no Mitsubishi manuals are provided, separately attach an explanatory note regarding
the symbol to each manual of the devices.
The requirements apply to batteries and/or devices with built-in batteries manufactured before the
enforcement date of the new EU Battery Directive (2006/66/EC).
APPENDIX
144 Appendix 6 Handling of Batteries and Devices with Built-in Batteries in EU Member States
INDEX
B RS-485 terminal resistor selector switch . . . . . . . .15

RUN/STOP/RESET switch . . . . . . . . . . . . . 15,114
BAT LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Battery connector . . . . . . . . . . . . . . . . . . . . . . . 15 I
Battery holder . . . . . . . . . . . . . . . . . . . . . . . . . . 15 S
Built-in analog I/O terminal block. . . . . . . . . . . . . 15 SD LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Built-in Ethernet communication connector . . . . . 14 SD memory card disable switch . . . . . . . . . . . . . .15
Built-in RS-485 communication terminal block . . . 15 SD memory card slot. . . . . . . . . . . . . . . . . . . . . .15
SD/RD LED . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
C Sink input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Sink output. . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
CARD LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Source input. . . . . . . . . . . . . . . . . . . . . . . . . . . .83
CPU module fixing screw hole . . . . . . . . . . . . . . 16 Source output. . . . . . . . . . . . . . . . . . . . . . . . . . .92
D T
DIN rail mounting groove . . . . . . . . . . . . . . . . . . 16 Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
DIN rail mounting hooks . . . . . . . . . . . . . . . . . . . 14 Terminal block cover . . . . . . . . . . . . . . . . . . . . . .14
Terminal block mounting screws. . . . . . . . . . . . . .15
E Top cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
ERR LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Expansion adapter connecting hooks . . . . . . . . . 14
Expansion adapter connector cover . . . . . . . . . . 16
Expansion board connector . . . . . . . . . . . . . . . . 15
Expansion board connector cover . . . . . . . . . . . . 14
Extension connector . . . . . . . . . . . . . . . . . . . . . 15
Extension connector cover . . . . . . . . . . . . . . . . . 14
G
Genuine product certification label . . . . . . . . . . . 16
I
Input display LED . . . . . . . . . . . . . . . . . . . . . . . 14
Installing directly . . . . . . . . . . . . . . . . . . . . . . 64,67
Installing on DIN rail . . . . . . . . . . . . . . . . . . . . . 64
M
Memory capacity . . . . . . . . . . . . . . . . . . . . . . . . 23
N
Nameplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Number of input/output points . . . . . . . . . . . . . . . 39
Number of remote I/O points . . . . . . . . . . . . . . . 46
O
Output display LED . . . . . . . . . . . . . . . . . . . . . . 14
P
P.RUN LED . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
PWR LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
R
RD LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
145
REVISIONS
Revision date Revision Description
October 2014 A First edition
January 2015 B ■Added or modified parts
RELEVANT MANUALS, TERMS, Section 1.1, 2.1, 2.2, 2.6, 2.7, 2.8, 3.1, 3.4, 3.5, 3.6, 3.7, 3.8, 3.9,
3.12, Chapter 4, Section 5.4, 5.5, 6.1, 6.6, 7.1, 7.3, 8.2, 8.3, 9.1, 9.2, 9.3, 9.7, Appendix 2, 4
This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot
be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual.
2014 MITSUBISHI ELECTRIC CORPORATION
146
WARRANTY
Please confirm the following product warranty details before using this product.
1. Gratis Warranty Term and Gratis Warranty 2. Onerous repair term after discontinuation
Range of production
If any faults or defects (hereinafter "Failure") found to 1) Mitsubishi shall accept onerous product repairs for
be the responsibility of Mitsubishi occurs during use of seven (7) years after production of the product is
the product within the gratis warranty term, the discontinued.
product shall be repaired at no cost via the sales Discontinuation of production shall be notified with
representative or Mitsubishi Service Company. Mitsubishi Technical Bulletins, etc.
However, if repairs are required onsite at domestic or 2) Product supply (including repair parts) is not
overseas location, expenses to send an engineer will available after production is discontinued.
be solely at the customer's discretion. Mitsubishi shall
not be held responsible for any re-commissioning,
3. Overseas service
maintenance, or testing on-site that involves Overseas, repairs shall be accepted by Mitsubishi's
replacement of the failed module. local overseas FA Center. Note that the repair
conditions at each FA Center may differ.
[Gratis Warranty Term] 4. Exclusion of loss in opportunity and
The gratis warranty term of the product shall be for secondary loss from warranty liability
one year after the date of purchase or delivery to a Regardless of the gratis warranty term, Mitsubishi
designated place. Note that after manufacture and shall not be liable for compensation of damages
shipment from Mitsubishi, the maximum distribution caused by any cause found not to be the responsibility
period shall be six (6) months, and the longest gratis of Mitsubishi, loss in opportunity, lost profits incurred
warranty term after manufacturing shall be eighteen to the user or third person by failure of Mitsubishi
(18) months. The gratis warranty term of repair parts products, special damages and secondary damages
shall not exceed the gratis warranty term before whether foreseeable or not, compensation for
repairs. accidents, and compensation for damages to products
other than Mitsubishi products, replacement by the
[Gratis Warranty Range] user, maintenance of on-site equipment, start-up test
run and other tasks.
1) The range shall be limited to normal use within the
usage state, usage methods and usage 5. Changes in product specifications
environment, etc., which follow the conditions and The specifications given in the catalogs, manuals or
precautions, etc., given in the instruction manual, technical documents are subject to change without
user's manual and caution labels on the product. prior notice.
2) Even within the gratis warranty term, repairs shall 6. Product application
be charged for in the following cases. 1) In using the Mitsubishi MELSEC programmable
a) Failure occurring from inappropriate storage or controller, the usage conditions shall be that the
handling, carelessness or negligence by the application will not lead to a major accident even if
user. Failure caused by the user's hardware or any problem or fault should occur in the
software design. programmable controller device, and that backup
b) Failure caused by unapproved modifications, and fail-safe functions are systematically provided
etc., to the product by the user. outside of the device for any problem or fault.
c) When the Mitsubishi product is assembled into
2) The Mitsubishi programmable controller has been
a user's device, Failure that could have been
designed and manufactured for applications in
avoided if functions or structures, judged as
general industries, etc. Thus, applications in which
necessary in the legal safety measures the
the public could be affected such as in nuclear
user's device is subject to or as necessary by
power plants and other power plants operated by
industry standards, had been provided.
d) Failure that could have been avoided if respective power companies, and applications in
consumable parts (battery, backlight, fuse, which a special quality assurance system is
etc.) designated in the instruction manual had required, such as for railway companies or public
been correctly serviced or replaced. service purposes shall be excluded from the
e) Relay failure or output contact failure caused programmable controller applications.
by usage beyond the specified life of contact In addition, applications in which human life or
(cycles). property that could be greatly affected, such as in
f) Failure caused by external irresistible forces aircraft, medical applications, incineration and fuel
such as fires or abnormal voltages, and failure devices, manned transportation, equipment for
caused by force majeure such as earthquakes, recreation and amusement, and safety devices,
lightning, wind and water damage. shall also be excluded from the programmable
g) Failure caused by reasons unpredictable by controller range of applications.
scientific technology standards at time of However, in certain cases, some applications may
shipment from Mitsubishi. be possible, providing the user consults their local
h) Any other failure found not to be the Mitsubishi representative outlining the special
responsibility of Mitsubishi or that admitted not requirements of the project, and providing that all
to be so by the user. parties concerned agree to the special
circumstances, solely at the user's discretion.
147
TRADEMARKS
Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or
other countries.
Ethernet is a trademark of Xerox Corporation.
Anywire is a registered trademark of the Anywire Corporation.
MODBUS is a registered trademark of Schneider Electric SA.
Phillips is a registered trademark of Phillips Screw Company.
SD logo and SDHC logo are trademarks or registered trademarks of SD-3C, LLC.
The company name and the product name to be described in this manual are the registered trademarks or trademarks of
each company.
148
Manual number: JY997D55301B

Model: FX5U-U-HW-E
Model code: 09R536
When exported from Japan, this manual does not require application to the
Ministry of Economy, Trade and Industry for service transaction permission.
HEAD OFFICE: TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
HIMEJI WORKS: 840, CHIYODA MACHI, HIMEJI, JAPAN
Specifications are subject to change without notice.

FX5U - Hardware Manual

Uploaded by

Copyright:

Available Formats

FX5U - Hardware Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

FX5U - Hardware Manual

Uploaded by

Copyright:

Available Formats

Truy cập website https://plcmitsubishi.

Indicates that incorrect handling may cause hazardous conditions, resulting in

Indicates that incorrect handling may cause hazardous conditions, resulting in

[STARTUP AND MAINTENANCE PRECAUTIONS]

[STARTUP AND MAINTENANCE PRECAUTIONS]

Regarding use of this product

CHAPTER 3 PRODUCT LIST 31

CHAPTER 4 SYSTEM CONFIGURATION 38

Screw terminal block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

CHAPTER 7 OPERATION ADJUSTMENT 110

CHAPTER 8 MAINTENANCE AND INSPECTION 115

CHAPTER 9 TROUBLESHOOTING 120

9.3 Troubleshooting using the engineering tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

Manual name <manual number> Description

1.1 Part Names

With cover open

No. Name Description

When the terminal block covers are open

Left side/right side

Top side/bottom side

2.1 Generic Specifications 2

Dielectric withstand voltage test and insulation resistance test

■ CPU module, I/O module

■Expansion board, expansion adapter

■Intelligent function module

2.2 Power Supply Specifications

2.3 Input Specifications

T1 (pulse width) T2 (rise/fall time)

• When using external power supply

2.4 Output Specifications

A number is entered in the of [COM ].

A number is entered in the of [COM ]. A number is entered in the of [+V ].

2.5 Input/Output Derating Curve

50 55 Ambient temperature

2.6 Performance Specifications

Number of device points

2.7 Built-in Analog Specifications

*1 "Digit" refers to digital values.

2.8 Communication Specifications

Built-in Ethernet communication

Built-in RS-485 communication

2.9 External Dimensions

(mounting hole pitch)

Model W W1 (mounting hole pitch) Mass (weight)

Model W W1 (mounting hole pitch) Mass (weight)

2.10 Terminal Layout

Built-in RS-485 terminal

Built-in analog terminal

Built-in Ethernet connector

Power, input/output terminal block

Common terminal Output terminal Partition

• Indication of power supply terminals

Y0 2 Y4 6 Y10 12 Y14 16 Y20 22 24 26 Y30 32 34 36 COM5

Y0 2 Y4 6 Y10 12 Y14 16 Y20 22 24 26 Y30 32 34 36 +V5

Y0 2 Y4 6 Y10 12 Y14 16 Y20 22 24 26 Y30 32 34 36 Y40 42 44 46

Y0 2 Y4 6 Y10 12 Y14 16 Y20 22 24 26 Y30 32 34 36 Y40 42 44 46

3.1 Overall Configuration

FX5 extension power supply module

3.2 CPU Module

AC power supply common to 24 V DC sink and source input