Remove Steering Clutch Hydraulic Control Valve: SENR70110019
Remove Steering Clutch Hydraulic Control Valve: SENR70110019
1. Disconnect two rods (1) from the levers of the steering clutch hydraulic control valve.
3. Disconnect four lines (4), (5), (6) and (7) from the brake hydraulic mechanism housing.
4. Remove four bolts (2) that hold the flange to the bevel gear case.
5. Remove four bolts (8). Remove steering clutch hydraulic control valve (9).
6. Check the seals in the bevel gear case and the steering clutch hydraulic control valve. If the seals have damage, use new parts for replacement.
1. Install new seals (3) in the bevel gear case and the steering clutch hyraulic control valve. Put clean SAE 30 oil on the seals.
2. Put the steering clutch hydraulic control valve (1) in position on the bevel gear case.
4. Install the four bolts that hold the flange to the bevel gear case.
5. Connect four lines (6), (7), (8) and (9) to the brake hydraulic mechanism housing.
6. Connect oil line (5) to the steering clutch hydraulic control valve.
end by:
https://sis2.cat.com/?_ts=1635234719811#/print-preview/service/%257B%2522title%2522%253A%2522Steering%2520Clutch%2520Hydraulic%2520Control%2520Valve%2520(SENR7011-01)%2522%252C%2522f… 1/4
26/10/2021 09:26 SIS 2.0
b) remove brake hydraulic mechanism and steering clutch hydraulic control relief valve (direct drive)
1. Remove five bolts (1). Remove housing (4) from housing (2). Remove bolts that hold two flanges (3) to housing (4). Remove flanges (3).
3. Remove plunger (9), bushings (8), spring (7), washer (11), retainer (6) and washer (5) from the valve. Disassemble the other valve the same
way.
4. Remove ring (13) and plug (12) from housing (4). Remove seal (14) from the plug. Remove the other plug from the housing.
5. Remove slug (15) and piston (16) from valve spool (17).
6. Remove levers (18) from the shafts. Remove the keys from the shafts.
7. Hit the ends of the shafts with a soft faced hammer. Remove spacers (19) and bearings (20).
8. Remove snap ring (22) and washer (21) from the shaft.
9. Remove bolts (23). Remove lever assemblies (26), shafts (27) and washers from the housing.
https://sis2.cat.com/?_ts=1635234719811#/print-preview/service/%257B%2522title%2522%253A%2522Steering%2520Clutch%2520Hydraulic%2520Control%2520Valve%2520(SENR7011-01)%2522%252C%2522f… 2/4
26/10/2021 09:26 SIS 2.0
10. Remove pins (24) and rollers (25) from the levers.
11. Remove seals (28) and bearings (29) from the housing.
1. Install bearings (1) in the shaft housing with tooling (A). Make sure the bearings are even with the seal bores.
3. Put rollers (4) in position on levers (6). Install pins (3) and cotter pins (5).
4. Slide shaft (12) into position through the bearing end of the housing. Install lever (9), washer (7) and snap ring (8) on shaft (12). Make sure the
grooves in the levers are engaged with the keys (10) in the shafts. Tighten bolts (11).
https://sis2.cat.com/?_ts=1635234719811#/print-preview/service/%257B%2522title%2522%253A%2522Steering%2520Clutch%2520Hydraulic%2520Control%2520Valve%2520(SENR7011-01)%2522%252C%2522f… 3/4
26/10/2021 09:26 SIS 2.0
5. Install bearings and spacers (13) over the ends of the shafts.
6. Put new seals on plugs (19). Install plugs (19) and snap rings (20) in the valve spool housing.
7. Install slugs (22) and pistons (21) in the valve spool. Put springs (18) and (23) into position on the valve spool. Install the valve spool assembly in
the housing.
8. Install spacers (15), spring (24), bushing (25) and plunger (16) in the housing. Tighten bolts (26).
9. Put shaft housing (17) in position on valve spool housing (14). Install the bolts that hold the housings together.
end by:
b) install brake hydraulic mechanism and steering clutch hydraulic control relief valve (direct drive)
PIP-10706161
2021/10/26
08:25:28+01:00
SENR70110019
© 2021 Caterpillar Inc.
Caterpillar:
Confidential Green
https://sis2.cat.com/?_ts=1635234719811#/print-preview/service/%257B%2522title%2522%253A%2522Steering%2520Clutch%2520Hydraulic%2520Control%2520Valve%2520(SENR7011-01)%2522%252C%2522f… 4/4