Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 25 views

    Mechanical Questions

    Uploaded by

    arup
    This document contains a 25 question mechanical module test covering topics like least count of vernier callipers, micrometer vs dial gauge conversions, tire and engine specifications, properties of coolant and brake fluid, gear trains and common rail fuel systems.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    Mechanical Questions

    Uploaded by

    arup
    25 views6 pages
    This document contains a 25 question mechanical module test covering topics like least count of vernier callipers, micrometer vs dial gauge conversions, tire and engine specifications, properties of coolant and brake fluid, gear trains and common rail fuel systems.

    Original Description:

    Mechanical Module Q/A

    Original Title

    Mechanical questions

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document contains a 25 question mechanical module test covering topics like least count of vernier callipers, micrometer vs dial gauge conversions, tire and engine specifications, properties of coolant and brake fluid, gear trains and common rail fuel systems.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    25 views6 pages

    Mechanical Questions

    Uploaded by

    arup
    This document contains a 25 question mechanical module test covering topics like least count of vernier callipers, micrometer vs dial gauge conversions, tire and engine specifications, properties of coolant and brake fluid, gear trains and common rail fuel systems.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    You are on page 1of 6

    G B Pant Institute of Technology, Okhla Phase- III, New Delhi 110020

    Automotive Mechatronic Research Center – ADAM Course

    Name: _______________________________________________________________________

    Module Name: Mechanical Module Time: 50 Minutes


    (Each question carries 2 marks)

    1. Formula for least count of Vernier Calliper is _____


    Ans:

    2. What is the major difference between Micrometer and Dial Gauge?

    Ans:

    3. 260 Kilo Pascal = ____ Bar.

    Ans:

    4. 25 inch = ___ mm.

    Ans:

    5. Explain the tyre specification/designation : 245/45R 19-102Y

    Ans:

    1
    6. As per MB specification what is the grade of engine oil , AT fluid and Brake fluid?

    Ans:

    7. What would be the rpm of camshaft sprocket if crankshaft is rotating with 1000 rpm?

    Ans:

    8. What would be replaced in every maintenance service of a MB Car?

    Ans:

    9. What are the reasons for brake fluid level to drop in its reservoir?

    Ans:

    10. Bolt size is M10×1.5-6g-S. What does this mean? Is this coarse or fine threaded bolt?

    Ans:

    11. The rail pressure of the Gasoline engine is _____Bar


    a. 100 b. 200 c. 300 d. 400

    Ans:

    2
    12. Explain the engine specification : 112 062 2 2 143 347

    Ans:

    13. Explain the Chassi specification : WDC 166 0 56 6 M 009518

    Ans:

    14. Write the properties of coolant.


    Ans:

    15. Write the properties of Brake fluid.


    Ans:

    3
    16. What should be the length of a torque wrench, if 150 Nm torque is required to be applied to
    wheel bolts with hand force of 100 Newton?

    Ans:

    2 5
    4
    3

    Fig: 1

    Refer the Fig. 1 above , gear train image and select the correct option

    17. Refer Fig.1 : Assuming that gear “1” is rotating in clockwise direction , gear “1” & “2” are
    external mesh , gear “2” & “3” are in internal mesh , gear “3” & “4” are external mesh
    and gear “4 “ & “5” ar external mesh. Then what will be the direction of gear “5”.

    a. Clockwise b. anticlockwise c. Gear locks d. Counter clockwise

    Ans:

    4
    18. Ref. Fig.1: If gear “1” is rotating with 100 rpm, what will be the speed of gear “3” . Following are
    the number of teeth’s for each gears. Gear “1” = 32 teeth . Gear “2” = 16 teeth. Gear “ 3” = 8
    teeth.

    a. 150 rpm b. 300 rpm c. 400 rpm d. 500rpm

    Ans:

    19. Coolant test is done by ______.

    From the Fig. 2 below answer the following questions :

    Fig. 2

    20. Identify common rails and injectors in the Fig. 2

    21. Identify High pressure line and low pressure line in the Fig.2

    22. Identify High pressure punp and fuel filter in the Fig. 2

    23. Identify fuel return line in the Fig. 2

    5
    24. Explain venturi effect (ref. fig. 2).

    25. _____ bar pressure is in low pressure circuit and _____ bar pressure is maintained in high
    pressure circuit. ( ref. Fig.2).

    You might also like