Iso 15243 2017

INTERNATIONAL ISO
STANDARD 15243
Second edition
2017-03
Rolling bearings — Damage and

failures — Terms, characteristics and
causes
Roulements — Détérioration et défaillance — Termes,
caractéristiques et causes
iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 15243:2017
https://standards.iteh.ai/catalog/standards/sist/80beed0a-2220-48e9-b6ad-
a64ac28c7266/iso-15243-2017
Reference number
ISO 15243:2017(E)
© ISO 2017
ISO 15243:2017(E)


(standards.iteh.ai)
ISO 15243:2017
a64ac28c7266/iso-15243-2017
COPYRIGHT PROTECTED DOCUMENT

© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

ISO 15243:2017(E)

Contents Page
Foreword......................................................................................................................................................................................................................................... iv
Introduction...................................................................................................................................................................................................................................v
1 Scope.................................................................................................................................................................................................................................. 1
2 Normative references....................................................................................................................................................................................... 1
3 Terms and definitions...................................................................................................................................................................................... 1
4 Classification of failure modes occurring in rolling bearings................................................................................ 2
5 Failure modes........................................................................................................................................................................................................... 3
5.1 Rolling contact fatigue....................................................................................................................................................................... 3
5.1.1 General description of rolling contact fatigue......................................................................................... 3
5.1.2 Subsurface initiated fatigue..................................................................................................................................... 4
5.1.3 Surface initiated fatigue.............................................................................................................................................. 4
5.2 Wear.................................................................................................................................................................................................................. 6
5.2.1 General description of wear.................................................................................................................................... 6
5.2.2 Abrasive wear...................................................................................................................................................................... 6
5.2.3 Adhesive wear..................................................................................................................................................................... 7
5.3 Corrosion...................................................................................................................................................................................................... 9
5.3.1 General description of corrosion........................................................................................................................ 9
5.3.2 Moisture corrosion......................................................................................................................................................... 9
5.3.3 Frictional corrosion..................................................................................................................................................... 10
5.4 iTeh STANDARD PREVIEW
Electrical erosion................................................................................................................................................................................ 12
5.4.1 General description of electrical erosion.................................................................................................. 12
(standards.iteh.ai)
5.4.2 Excessive current erosion...................................................................................................................................... 12
5.4.3 Current leakage erosion.......................................................................................................................................... 13
5.5 ISO 15243:2017
Plastic deformation........................................................................................................................................................................... 14
5.5.1 General description of plastic deformation............................................................................................ 14
5.5.2 Overload deformation a64ac28c7266/iso-15243-2017
............................................................................................................................................... 14
5.5.3 Indentations from particles.................................................................................................................................. 16
5.6 Cracking and fracture...................................................................................................................................................................... 17
5.6.1 General description of cracking and fracture........................................................................................ 17
5.6.2 Forced fracture................................................................................................................................................................ 17
5.6.3 Fatigue fracture............................................................................................................................................................... 18
5.6.4 Thermal cracking........................................................................................................................................................... 19
Annex A (informative) Failure analysis — Illustrations of damage — Other investigations
— Explanation of terms used................................................................................................................................................................20
Bibliography.............................................................................................................................................................................................................................. 53
© ISO 2017 – All rights reserved iii

ISO 15243:2017(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.
(standards.iteh.ai)
The committee responsible for this document is ISO/TC 4, Rolling bearings.
This second edition cancels and replaces the firstISO edition (ISO 15243:2004), which has been technically
15243:2017
revised. https://standards.iteh.ai/catalog/standards/sist/80beed0a-2220-48e9-b6ad-
a64ac28c7266/iso-15243-2017
iv © ISO 2017 – All rights reserved

ISO 15243:2017(E)

Introduction
In practice, damage and/or failure of a rolling bearing can often be the result of several mechanisms
operating simultaneously. The failure can result from improper transport, handling, mounting or
maintenance or from faulty manufacture of the bearing or its adjacent parts. In some instances, failure
is due to a design compromise made in the interests of economy or from unforeseen operating and
environmental conditions. It is the complex combination of design, manufacture, mounting, operation
and maintenance that often causes difficulty in establishing the root cause of failure.
NOTE Be aware that counterfeit bearings are circulated in the market. They might look as original bearings,
but their use often lead to very early damage or failure.
In the event of extensive damage to or catastrophic failure of the bearing, the evidence is likely to be
lost and it will then be impossible to identify the root cause of failure. It is therefore important to stop
equipment in time to enable appropriate bearing damage analysis (see Figure 1). In all cases, knowledge
of the actual operating conditions of the assembly and the maintenance history is of utmost importance.

(standards.iteh.ai)
NOTE The spall started just behind the dent in the raceway [a)]. Over a period of time, the spalling becomes
ISO 15243:2017
more severe [b) and c)]. If not stopped in time, the proof of the root cause disappears [d)].
a64ac28c7266/iso-15243-2017
Figure 1 — Progression of bearing damage
The classification of bearing failure established in this document is based primarily upon the features
visible on rolling contact surfaces and other functional surfaces. Consideration of each feature is
required for reliable determination of the root cause of bearing failure. Since more than one failure
mechanism may cause similar effects to these surfaces, a description of appearance alone is often
inadequate for determining the cause of the failure. In such cases, the operating conditions need to be
considered. In some cases, the analysed damage is too advanced, and can be originated from different
primary causes. In these cases, it is interesting to look for simultaneous presence of indications to
determine the primary cause of the failure.
This document covers rolling bearings having steel rings and rolling elements. Damage to the rings of
bearings with ceramic rolling elements shows similar failure modes.
In this document, bearing life is as described in ISO 281[1], which provides formulae to calculate bearing
life taking a number of factors into consideration, such as bearing load carrying capacity, bearing load,
type of bearing, material, bearing fatigue load limit, lubrication conditions and degree of contamination.
© ISO 2017 – All rights reserved v

(standards.iteh.ai)
ISO 15243:2017
a64ac28c7266/iso-15243-2017
INTERNATIONAL STANDARD ISO 15243:2017(E)
Rolling bearings — Damage and failures — Terms,

characteristics and causes
1 Scope
This document classifies different modes of failure occurring in service for rolling bearings made of
standard bearing steels. For each failure mode, it defines and describes the characteristics, appearance
and possible root causes of failure. It will assist in the identification of failure modes based on
appearance.
For the purposes of this document, the following terms are explained:
— failure of a rolling bearing: the result of a damage that prevents the bearing meeting the intended
design performance or marks the end of service life;
— in service: as soon as the bearing has left the manufacturer’s factory;
— visible features: those that are possible to observe directly or with magnifiers or optical microscopes,
also those from pictures, but only with the use of non-destructive methods.
Consideration is restricted to characteristic forms of change in appearance and failure that have well-
defined appearance and which can be attributed to particular causes with a high degree of certainty.
The features of particular interest for explaining changes and failures are described. The various forms
(standards.iteh.ai)
are illustrated with photographs and the most frequent causes are indicated.
If the root cause cannot be reliably assessed by the examination and characterization of visual
ISO 15243:2017
features against thehttps://standards.iteh.ai/catalog/standards/sist/80beed0a-2220-48e9-b6ad-
information in this document, then additional investigations are to be considered.
These methods are summarized ina64ac28c7266/iso-15243-2017
A.3 and may involve, for example, the use of invasive methods
possibly including taking of cross sections, metallurgical structural analysis by visual and electronic
microscopes, chemical and spectrographic analysis. These specialized methods are outside the scope of
this document.
The failure mode terms shown in the subclause titles are recommended for general use. Where
appropriate, alternative expressions or synonyms used to describe the submodes are given and
explained in A.4.
Examples of rolling bearing failures are given in A.2, together with a description of the causes of failure
and proposed corrective actions.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 5593, Rolling bearings — Vocabulary
3 Terms and definitions

For the purposes of this document, the terms and definitions given in ISO 5593 and the following apply.
NOTE Explanations for terms for damage and failures are listed in A.4.
© ISO 2017 – All rights reserved 1

ISO 15243:2017(E)

ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http://w ww.electropedia.org/
— ISO Online browsing platform: available at http://w ww.iso.org/obp
3.1
characteristics
visual appearance that results from service performance
Note 1 to entry: Surface defects and types of geometrical change are defined in ISO 8785[3] and partly in
ISO 6601[2] (related to abrasive wear).
3.2
damage
any visible deterioration of the bearing operating surfaces or structures
3.3
event sequences
sequence of events leading to bearing failure (3.4) starting with initial damage (3.2) to the bearing
Note 1 to entry: At an early stage, this damage can result in loss of function or failure. In many cases, however,
the initial damage does not result in failure and the bearing continues to operate. This continued operation most
often leads to secondary damage which eventually results in failure. Secondary damage can introduce competing
modes of failure, which can make root cause analysis difficult.
3.4
failure
any condition where the bearing can no longer deliver its designed function
(standards.iteh.ai)
Note 1 to entry: This will include degradation of important rotational properties and warning of imminent
more extensive or complete failure, but may not be so advanced
ISO 15243:2017as to prevent rotation or support of the subject
machine elements. https://standards.iteh.ai/catalog/standards/sist/80beed0a-2220-48e9-b6ad-
a64ac28c7266/iso-15243-2017
Note 2 to entry: The extent of damage (3.2) required to cause a declaration of operational failure will depend on
the application. Applications requiring accurate smooth rotation will tolerate only very minor loss of properties.
Applications not sensitive to increased vibration, increased noise or reduced rotational accuracy may be able to
continue to deliver their performance for a restricted period.
3.5
failure mode
manner in which a bearing fails
4 Classification of failure modes occurring in rolling bearings

Preferably, one would classify rolling bearing damage and failures according to the root cause. However,
it is often not easy to distinguish between causes and characteristics (symptoms) or, in other words,
between failure mechanisms and failure modes. The large number of articles and books written on the
subject confirms this (see Bibliography). Therefore, in this document, failure modes are classified in
six main groups and various sub-groups (see Figure 2), based on their visible distinctive characteristic
appearance in service.
2 © ISO 2017 – All rights reserved

ISO 15243:2017(E)


(standards.iteh.ai)
ISO 15243:2017
a64ac28c7266/iso-15243-2017
Figure 2 — Classification of failure modes
5 Failure modes
5.1 Rolling contact fatigue
5.1.1 General description of rolling contact fatigue
Rolling contact fatigue is caused by the repeated stresses developed in the contacts between the rolling
elements and the raceways. Fatigue is manifested visibly as a change in the structure (microstructure)

ISO 15243:2017(E)

and as spalling of material from the surface (macrostructure) that, in most of the cases, could be
consequential to a change in microstructure.
NOTE Spalling and flaking are synonyms (see A.4).
5.1.2 Subsurface initiated fatigue
Under the influence of cyclic loading in the rolling contacts described by the Hertzian theory,
stresses and material structural changes occur and microcracks are initiated at a location and depth
which depend on the applied load, the operating temperature, the material and its cleanliness and
microstructure. The initiation of the microcracks is often caused by inclusions in the bearing steel.
The changes might appear at metallurgical investigation (see A.3). These cracks propagate and when
they come to the surface, spalling occurs (see Figures 3 and 4).

(standards.iteh.ai)
Figure 3 — Initial subsurface spalling in a deep groove ball bearing — Rotating inner ring
ISO 15243:2017
a64ac28c7266/iso-15243-2017
Figure 4 — Advanced subsurface spalling in a tapered roller bearing — Stationary inner ring
5.1.3 Surface initiated fatigue
Fatigue initiated from the surface is typically caused by surface distress.

Surface distress is damage initiated at the rolling contact surfaces due to plastic deformation of the
surface asperities (smoothing, burnishing, glazing). Contact between the asperities of the rolling
element and bearing raceway is most often the result of inadequate lubrication conditions (insufficient
lubricant film thickness). This contact may be caused by insufficient lubrication flow/availability,
improper lubricant for the application, operating temperatures beyond the expected level or rough
surface finishes. Contact and plastic deformation of the surface asperities can lead to
— asperity microcracks (see Figure 5),
— asperity microspalls (see Figure 6), and

ISO 15243:2017(E)

— microspalled areas (grey stained) (see Figure 7).

Sliding motion under low lubricant film conditions can significantly accelerate the surface damage.
For cases where film thickness is sufficient for normal operating conditions, surface-initiated fatigue
may still occur. This can happen when particles are introduced into the contact area (see 5.5.3),
extreme loads plastically deform the surface or handling nicks are present. All three conditions result
in indentations in the raceways. Protrusions around the indentation exceed the height of the oil film,
resulting in deformation of surface asperities. Surface initiated fatigue caused by indentation arising
from plastic deformation is shown in A.2.6.2.
NOTE ISO 281[1] includes surface related calculation parameters that are known to have an influence on the
bearing life such as material, lubrication, environment, contamination particles and bearing load.

(standards.iteh.ai)
Figure 5 — Asperity microcracks and microspalls on a raceway
ISO 15243:2017
a64ac28c7266/iso-15243-2017
Figure 6 — Surface initiated microspalls on a raceway

ISO 15243:2017(E)

Figure 7 — Microspalled areas on a raceway
5.2 Wear iTeh STANDARD PREVIEW

5.2.1 General description of wear (standards.iteh.ai)
Wear is the progressive removal of material from ISO the surface, resulting from the interaction of two
15243:2017
sliding or rolling/sliding contacting surfaces during service.
a64ac28c7266/iso-15243-2017
5.2.2 Abrasive wear
Abrasive wear (particle wear, three-body wear) is the removal of material due to sliding in presence
of hard particles. It is the result of a hard surface or particle removing material from another surface
through a cutting or ploughing action when sliding across it. The surfaces become dull to a degree, which
varies according to the coarseness and nature of the abrasive particles (see Figure 8). These particles
gradually increase in number as material is worn away from the running surfaces and, possibly, the
cage (see Figure 9). Finally, the wear becomes an accelerating process that results in a failed bearing.
Although the surfaces normally become dull to a certain extent, when the abrasive particles are very
fine, a polishing effect might occur, resulting in very shiny surfaces (see Figure 10).
NOTE The “running-in” of a rolling bearing is a natural short process after which the running behaviour,
e.g. noise or operating temperature, stabilizes or even improves. As a consequence, the running path or running
track becomes visible; however this is not indicating that the bearing is damaged.

ISO 15243:2017(E)

Figure 8 — Abrasive wear on the inner ring of a spherical roller bearing

Figure 9 — Advanced abrasive wear on the cage pockets of a solid metal cage
(standards.iteh.ai)
ISO 15243:2017
a64ac28c7266/iso-15243-2017
Figure 10 — Abrasive wear on the raceway of the large rib surface of the inner ring and on the
large end face of rollers in a tapered roller bearing
5.2.3 Adhesive wear
Adhesive wear is characterized by a transfer of material from one surface to another with frictional heat
and, sometimes, tempering or rehardening of the surface. This produces localized stress concentrations
with the potential for cracking or spalling of the contact areas.
Smearing (skidding, galling, scoring, frosting) occurs because of inadequate lubrication conditions
when sliding occurs and localized temperature rises from friction cause adhesion of the contacting
surfaces, resulting in material transfer. This typically happens between rolling elements and raceways
if the rolling elements are too lightly loaded and subjected to severe acceleration on their re-entry
into the load zone (see Figures 11 and 12). In severe cases of smearing, seizing may result. Smearing is
usually a sudden occurrence as opposed to an accumulated wear process.

ISO 15243:2017(E)

Smearing can also occur on the rib faces and on the ends of the rollers due to inadequate lubrication (see
Figure 13). In full complement (cageless) bearings, smearing can also occur in the contacts between
rolling elements, depending on lubrication and rotation conditions.
If a bearing ring moves (creeps) relative to its seat because of inadequate retention on the shaft or in
the housing, then smearing (also called scuffing) can occur in the bearing bore, the outside diameter
or on the shaft or in the housing seat. Because of the minute difference in the diameters of the two
components, they will have a minute difference in their circumferences and, consequently, when
brought into contact at successive points by the radial load rotating with respect to the ring, will rotate
at minutely different speeds. This rolling motion of the ring against its seating with a minute difference
in the rotational speeds is termed “creep”.
When creep occurs, the asperities in the ring/seat contact region are over-rolled, which can cause the
surface of the ring to take on a shiny appearance. The over-rolling during creeping is often, but not
always, accompanied by sliding in the ring/seat contact, and then other damage will also be visible, e.g.
score marks, fretting corrosion and wear. Under certain loading conditions and when the ring/seating
interference fit is insufficiently tight, fretting corrosion will predominate (see A.2.4.2.1 and A.2.4.2.2).
Furthermore, with a loose radial fit, creep can also occur between the face of a ring and its axial
abutment. In severe cases, this can lead to transverse thermal cracks and finally cause cracking of the
ring (see 5.6.4).

(standards.iteh.ai)
ISO 15243:2017
a64ac28c7266/iso-15243-2017
Figure 11 — Smearing on the outer ring raceway of a cylindrical roller bearing
Figure 12 — Smearing on the outer ring raceways of a spherical roller bearing

ISO 15243:2017(E)

Figure 13 — Smearing on the side face of rollers of a cylindrical roller bearing
5.3 Corrosion
5.3.1 General description of corrosion
Corrosion is the result of a chemical reaction on metal surfaces.
5.3.2 Moisture corrosion
When bearing components are in contact with moisture or aggressive media (e.g. water or acids),
oxidation or corrosion (rust) of surfaces takes place (see Figure 14). Subsequently, the formation of
corrosion pits occurs and finally spalling of the surface occurs (see Figure 15).
A specific form of moisture corrosion can be observed in the contact areas between rolling elements
and bearing rings where the water content in the lubricant or the degraded lubricant reacts with the
(standards.iteh.ai)
surfaces of the adjacent bearing elements. During static periods, the advanced stage will result in dark
discolouration of the contact areas at intervals corresponding to the ball/roller pitch (see Figure 16);
eventually producing corrosion pits. ISO 15243:2017
a64ac28c7266/iso-15243-2017
Figure 14 — Moisture corrosion on the cage and rollers of a needle roller thrust bearing
Figure 15 — Moisture corrosion on the outer ring raceway of a cylindrical roller bearing

Iso 15243 2017

Uploaded by

Copyright:

Available Formats

Iso 15243 2017

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Iso 15243 2017

Uploaded by

Copyright:

Available Formats

INTERNATIONAL ISO

Rolling bearings — Damage and

iTeh STANDARD PREVIEW

iTeh STANDARD PREVIEW

COPYRIGHT PROTECTED DOCUMENT

ii ﻿ © ISO 2017 – All rights reserved

© ISO 2017 – All rights reserved ﻿ iii

iv ﻿ © ISO 2017 – All rights reserved

iTeh STANDARD PREVIEW

© ISO 2017 – All rights reserved ﻿ v

Rolling bearings — Damage and failures — Terms,

3 Terms and definitions

© ISO 2017 – All rights reserved ﻿ 1

4 Classification of failure modes occurring in rolling bearings

2 ﻿ © ISO 2017 – All rights reserved

iTeh STANDARD PREVIEW

Figure 2 — Classification of failure modes

5.1 Rolling contact fatigue

5.1.1 General description of rolling contact fatigue

© ISO 2017 – All rights reserved ﻿ 3

5.1.2 Subsurface initiated fatigue

iTeh STANDARD PREVIEW

5.1.3 Surface initiated fatigue

Fatigue initiated from the surface is typically caused by surface distress.

4 ﻿ © ISO 2017 – All rights reserved

— microspalled areas (grey stained) (see Figure 7).

iTeh STANDARD PREVIEW

Figure 6 — Surface initiated microspalls on a raceway

© ISO 2017 – All rights reserved ﻿ 5

Figure 7 — Microspalled areas on a raceway

5.2 Wear iTeh STANDARD PREVIEW

6 ﻿ © ISO 2017 – All rights reserved

Figure 8 — Abrasive wear on the inner ring of a spherical roller bearing

iTeh STANDARD PREVIEW

5.2.3 Adhesive wear

© ISO 2017 – All rights reserved ﻿ 7

iTeh STANDARD PREVIEW

Figure 11 — Smearing on the outer ring raceway of a cylindrical roller bearing

Figure 12 — Smearing on the outer ring raceways of a spherical roller bearing

8 ﻿ © ISO 2017 – All rights reserved

Figure 13 — Smearing on the side face of rollers of a cylindrical roller bearing

5.3.1 General description of corrosion

Corrosion is the result of a chemical reaction on metal surfaces.

5.3.2 Moisture corrosion

© ISO 2017 – All rights reserved ﻿ 9

You might also like

ii © ISO 2017 – All rights reserved

© ISO 2017 – All rights reserved iii

iv © ISO 2017 – All rights reserved

© ISO 2017 – All rights reserved v

© ISO 2017 – All rights reserved 1

2 © ISO 2017 – All rights reserved

© ISO 2017 – All rights reserved 3

4 © ISO 2017 – All rights reserved

© ISO 2017 – All rights reserved 5

6 © ISO 2017 – All rights reserved

© ISO 2017 – All rights reserved 7

8 © ISO 2017 – All rights reserved

© ISO 2017 – All rights reserved 9