Utilizing Peakvuetm Technology For Continuous Valve Health Monitoring On Reciprocating Compressors Csi Technologies en 39858

Whitepaper
Machinery Health™ Management August 2014
Utilizing PeakVueTM Technology for

Continuous Valve Health Monitoring on
Reciprocating Compressors
By Scott Bassett
With the expansions that are occurring in the natural gas (i.e. Fracking) industry, more emphasis is being placed on the reliability
and health of the intake and exhaust valves on compressors. When a valve begins to exhibit signs of leakage, compressor efficiency
can be greatly compromised. By using Emerson’s PeakVue technology, along with the Emerson CSI 6500 monitoring system, the
health of individual valves can be assessed and addressed in a timely manner in order to maintain maximum efficiency.
The CSI 6500 is especially qualified for this application due to continuous monitoring with the unique PeakVue methodology.
Trend values can be tracked and monitored on each valve so that the valve in question can be repaired or replaced in a timely
manner instead of having to replace a complete set. The transient capabilities also allows for replay of events in real time allowing for
further diagnostic capabilities.
In the following examples, we have outfitted a reciprocating compressor pumping “wet” gas with high frequency accelerometer
mounted on all 1st stage intake and exhaust valves. Wet gas refers to gas from the fracking method that has retained a large
amount of liquid content. We are also monitoring all of the crossheads and taking an axial reading on each throw in order to monitor
for looseness and or impacting that will occur as some of the mechanical components begin to wear.
It has been well documented that PeakVue data is a good indicator of high frequency occurrences such as flow turbulence and
friction. In this study we will be showing the flow turbulence that occurs as each valve opens and closes and relate it to a consistent
time in each revolution in order to determine valve action.
We will utilize the circular waveforms for our pattern recognition in determining the valve health. The circular waveform plots simply
overlay one rotation on top of another instead of plotting it in strip format. This particular format enhances the repeating pattern
seen in each revolution.
Whitepaper August 2014
Case Study
The compressors have been outfitted with a high frequency (10 mv/g) accelerometer mounted on one of the studs/bolts that hold
the valve cover in place. Standard accelerometers are also mounted vertically on the crosshead section, and axially on the head.
An optimized option is to utilize dual purpose high frequency/temperature accelerometers on the valves. This gives automatic
data correlation between temperature and vibration which gives additional predictive monitoring capabilities, as valves begin to
leak, gas temperatures rise. By monitoring individual valve temperatures as well as individual valve vibration signatures the
problem valve is more easily identified whereas monitoring cumulative data on a compressor head that only gives the general
region of the problem.
Due to the fact that each region of valves will act at a given point in each rotation of the compressor crankshaft, being able to
determine the phase angle of the occurrence is essential so that other signatures present in a given valve reading, can be related to
other events happening on the compressor.
By continuously monitoring the vibration and temperatures on the valve over time, a rate of degradation can be established
allowing the ability to predict the most optimum time to schedule valve replacement.
The following example shows how the trend values, as well as the pattern present in the circular waveform, changes as a valve
shows indications of leakage.
www.EmersonProcess.com 2
Whitepaper August 2014
Let’s first look at the trend value. Given the fact that we are dealing with a form of flow turbulence instead of impacting, what we
notice is that the amplitude actually decreases when a valve is not properly sealing. This is due to the fact that the Delta Pressure
is less across an improperly functioning valve, the usual “surge” of gas as the valve opens and closes is substantially reduced.
Now look at the circular waveforms. Notice the “crisp” event that is present on the upper plot. This can be directly related to the
phase angle of the compressor crankshaft and the timing of the valve. Also notice on the lower plot the event is less defined and
shows a large amount of energy present during the entire revolution.
These waveforms can also be viewed in standard strip format if preferred. Notice the energy present at approximately 225 degrees.
This is directly related to the timing of this particular valve operation. The top waveform shows a leaking or improperly functioning
valve, the bottom shows the same valve operating correctly two days prior.
www.EmersonProcess.com 3
Whitepaper December 2014
Conclusion
By utilizing PeakVueTM data collection, temperatures and viewing the circular waveform patterns we are able to determine the
operational health of the individual intake and exhaust valves independently. This information along with the associated trend
values from the peak-to-peak PeakVueTM waveform helps us to determine overall valve health as well as the rate of degradation of a
given valve. Adding the vibration data along with the individual valve temperatures, helps to pinpoint issues and allow for the proper
scheduling of repairs in preventing catastrophic valve related failures on reciprocating compressors.
©2014, Emerson Process Management.

The contents of this publication are presented for informational purposes only, and while every
effort has been made to ensure their accuracy, they are not to be construed as warranties or
guarantees, express or implied, regarding the products or services described herein or their
use or applicability. All sales are governed by our terms and conditions, which are available on
Emerson Process Management
request. We reserve the right to modify or improve the designs or specifications of our products
Reliability Solutions
at any time without notice.
835 Innovation Drive
Knoxville, TN 37932 All rights reserved. Machinery Health is a mark of one of the Emerson Process Management group
T (865) 675-2400 of companies. The Emerson logo is a trademark and service mark of Emerson Electric Co. All other
www.assetweb.com marks are the property of their respective owners.

Utilizing Peakvuetm Technology For Continuous Valve Health Monitoring On Reciprocating Compressors Csi Technologies en 39858

Uploaded by

Copyright:

Available Formats

Utilizing Peakvuetm Technology For Continuous Valve Health Monitoring On Reciprocating Compressors Csi Technologies en 39858

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Utilizing Peakvuetm Technology For Continuous Valve Health Monitoring On Reciprocating Compressors Csi Technologies en 39858

Uploaded by

Copyright:

Available Formats

Whitepaper

Machinery Health™ Management August 2014

Utilizing PeakVueTM Technology for

©2014, Emerson Process Management.

You might also like