POWER PULSE VALVES NC

2/2
Series
integral pilot (external exhaust)
threaded or Quick Mount connection 353
3/4 to 1 1/2
FEATURES
• The piston cartridge pulse valves are especially designed for dust collector
service applications, combining high flow, long life and extremely fast opening and
closing to produce reliable and economical operation
• The angle bodies and special piston cartridge result in unique operating features
required for dust collector service applications
• The high quality polyacetal (POM) piston cartridge guarantees a long operating
life and a large temperature range
• The design with Quick Mount connections eliminates the time consuming thread
cutting and sealing resulting in maximum flexibility while the valve will be
anchored to the pipes
• Built-in silencers reduce noise and prevent foreign particles from entering the valve
• The integral operators are provided with epoxy moulded F-class coils. Various
optional waterproof and explosionproof solenoids for use in potentially explosive
atmospheres (gas & dust) according to Directive ATEX 94/9/EC can be mounted
on the same basic valve (see pages 49 to 57)
• The components satisfy all relevant EC directives
General
Differential pressure (PS) 0,3 - 8,5 bar [1 bar = 100kPa]
Ambient temperature range -20 to +85°C
fluid temperature range (TS) piston
air -20 to +85°C POM (polyacetal)

CONSTRUCTION
Body Aluminium
Bonnet Aluminium
Quick Mount clamps Steel
Bolts Steel
Core tube Stainless steel
Core and plugnut Stainless steel
Core spring Stainless steel
Sealings & disc NBR (nitrile)
Piston/cartridge POM (polyacetal) / NBR (nitrile)
Shading coil Copper
Coil insulation class F
Connector Spade plug (cable Ø 6 - 8 mm)
Connector specification 3 x DIN 46244
Electrical safety IEC 335
ELECTRICAL CHARACTERISTICS
Standard voltages DC (=) : 24V
(Other voltages and 60 Hz on request) AC (~) : 24V - 115V - 230V / 50 Hz
nominal power ratings ambient
coil inrush holding hot/cold temperature
Availability, design and specifications are subject to change without notice. All rights reserved.

protection
type ~ ~ = range
(VA) (VA) (W) (W) (°C)
CM22-FB 14,5 11 6,3 -
-20 to +85 moulded IP65
CM22-FI (1) - - - 15 / 22
SPECIFICATIONS
operating pressure
flow
orifice differential (bar) catalogue
pipe coefficient coil type Quick Mount
size max. (PS) number
size Kv clamps
min. air
(mm) (m3/h) (l/min) ~/= ~ = (1) standard ATEX dust II3D
(G*) - Threaded pipe connection
3/4 20 14 233 0,3 8,5 CM22-FB CM22-FI SC E353A811 SCDU E353A811 -
1 25 23 383 0,3 8,5 CM22-FB CM22-FI SC E353A821 SCDU E353A821 -
1 1/2 40 46 768 0,3 8,5 CM22-FB CM22-FI SC E353A831 SCDU E353A831 -
(Ø) - Quick Mount connection on inlet
3/4 20 14 233 0,3 8,5 CM22-FB CM22-FI SC S353A811 SCDU S353A811 C117-281
1 25 23 383 0,3 8,5 CM22-FB CM22-FI SC S353A821 SCDU S353A821 C117-282
1 1/2 40 46 768 0,3 8,5 CM22-FB CM22-FI SC S353A831 SCDU S353A831 C117-290
(Ø) - Quick Mount connection on inlet & Outlet
X003GB-2009/R8

3/4 20 14 233 0,3 8,5 CM22-FB CM22-FI SC S353A711 SCDU S353A711 C117-281
1 25 23 383 0,3 8,5 CM22-FB CM22-FI SC S353A721 SCDU S353A721 C117-282
1 1/2 40 46 768 0,3 8,5 CM22-FB CM22-FI SC S353A731 SCDU S353A731 C117-290
(1) Intermittent duty, Relative Duty Time is 10%. Max. on time 1 min.
All leaflets are available on: www.asconumatics.eu
X003-5
 SOLENOID VALVES SERIES 353
OPTIONS
● Waterproof enclosure with embedded screw terminal coil according to protection class IP67, CEE 10.
● Explosionproof solenoids for hazardous locations according to “ATEX” and national standards.
● Explosionproof and watertight solenoids according to “NEMA” standards.
● Plug with visual indication and/or peak voltage suppression.
● Electronic timer.

INSTALLATION
● The valves can be mounted in any position without affecting operation.
● Pipe connection identifiers are: G*= combination thread according to ISO 228/1 and ISO 7/1 or Ø for Quick Mount.
● For Quick Mount types tightness is achieved by the O-ring sealing on the pipes (3/4"=Ø26,4 to 27,4 and 1"=Ø33,2 to 34,2
and 1 1/2"=Ø47,8 to 48,8) according to ISO 4200.
● Other pipe threads are available on request.
● Installation/maintenance instructions are included with each valve.
● Spare parts kit and replacement coils are available.

DIMENSIONS (mm), WEIGHT (kg)

A F

360 360

G
E H
Fig. 1: Threaded type Fig. 2: Quick Mount type (inlet only)
A F

Availability, design and specifications are subject to change without notice. All rights reserved.
B
C

D
G

E H
Fig. 3: Quick Mount type (inlet & outlet)

catalogue number A B C D E F G H weight (1) (C)

SC(DU) E353A811 48 156 106 42 50 22 39 77 0,52 Fig.1
SC(DU) E353A821 48 162 112 51 62 22 46 77 0,63 Fig.1
SC(DU) E353A831 48 191 141 60 71 22 62 112 1,17 Fig.1
SC(DU) S353A811 48 156 106 42 70 22 39 77 0,60 Fig.2
SC(DU) S353A821 48 162 112 51 83 22 46 77 0,69 Fig.2
SC(DU) S353A831 48 191 141 60 97 22 62 112 1,37 Fig.2
SC(DU) S353A711 48 176 126 62 70 22 39 77 0,68 Fig.3
X003GB-2009/R8

SC(DU) S353A721 48 183 133 71 83 22 46 77 0,80 Fig.3

SC(DU) S353A731 48 217 167 80. 97 22 62 112 1,58 Fig.3
(1) incl. coil and connector (C) construction type

All leaflets are available on: www.asconumatics.eu

X003-6
 PULSE VALVES 2/2
Series
single stage, integral pilot
threaded body or compression fitting
NC 353
IN
3/4 to 1
FEATURES
● The diaphragm pulse valves are especially designed for dust collector service applica-
tions, combining high flow, long life and extremely fast opening and closing to produce
reliable and economical operation
● The high flow, angle type bodies, springless construction, in combination with the

special diaphragm assemblies give the unique operating features required for dust
collector service applications
• Integral compression fittings for fast, easy, secure installation
• Built-in silencers reduce noise and prevent foreign particles from entering the valve
• The integral operators are provided with epoxy moulded F-class coils. Various optional
waterproof and explosionproof solenoids for use in potentially explosive atmospheres
(gas & dust) according to Directive ATEX 94/9/EC can be mounted on the same basic
valve (see pages 49 to 57)
• The valves satisfy all relevant EC directives

GENERAL
Differential pressure (PS) 0,35 - 8,5 bar [1 bar = 100kPa]
Ambient temperature range -20 to +85°C
fluids () temperature range (TS) diaphragm ()

air -20 to +85 °C TPE

MATERIALS IN CONTACT WITH FLUID

() Ensure that the compatibility of the fluids in contact with the materials is verified
Body Aluminium / Stainless steel 316L
Core tube Stainless steel
Core and plugnut Stainless steel
Core spring Stainless steel
Sealings & disc NBR (nitrile)
Diaphragm TPE (thermoplastic polyester elastomer)
Shading coil Copper
Coil insulation class F
Connector Spade plug (cable Ø 6 - 10 mm)
Connector specification ISO 4400
Electrical safety IEC 335
ELECTRICAL CHARACTERISTICS IN
Standard voltages DC (=): 24V
(Other voltages and 60 Hz on request) AC (~): 24V - 115V - 230V / 50 Hz
nominal power ratings operator
coil inrush holding hot/cold temperature
protection
type ~ ~ = range (TS)
(VA) (VA) (W) (W) (°C)
Availability, design and specifications are subject to change without notice. All rights reserved.

CM6-FT 34 15,6 6 - IP65/IP67

CM6-FT (1) - 14 / 20,8 IP65/IP67
-20 to +85
CMXX-FT 55 23 10,5 - ATEX-NF
CMXX-FF - - - 14 / 19,7 ATEX-NF
(1) Intermittent duty, Relative Duty Time is 10%. Max. on time is 1 min.

SPECIFICATIONS
operating pressure
flow differential (bar) prefix optional solenoids
pipe orifice catalogue
coefficient
size size max. (PS) number
Kv
FPM

min. air () ATEX

G (mm) (m³/h) (l/min) ~/= SC WP SCDU WP(T)DU NF aluminium stainless steel 316L
G - Threaded pipe connection
3/4 24 14 233 G353A043 G353A132 V
0,35 8,5 l l l l l
1 27 17 283 G353A044 G353A133 V
Ø - Compression fitting pipe connection
DP14240GB-2012/R01

3/4 24 14 233 G353-052 - V

0,35 8,5 l l l l l
1 27 17 283 G353-053 - V
l : Available feature

All leaflets are available on: www.asconumatics.eu

X003-7
 SOLENOID VALVES SERIES 353

OPTIONS
• Waterproof enclosure with embedded screw terminal coil according to protection class IP67, CEE 10
• Explosionproof solenoids for hazarous locations according to ATEX and national standards
• IECEx certification
• Compliance with “UL” standards
• Plug with visual indication and/or peak voltage suppression
• Electronic timer
• Valves can also be supplied with FPM (fluoroelastomer) diaphragms and seals. Use the appropriate optional suffix letter for
identification

INSTALLATION
• The valves can be mounted in any position without affecting operation
• Threaded pipe connection is G (ISO 228/1) or compression fitting
• For compression fitting types tightness is achieved by the compressed gasket on the blow tube
• The use of the rubber gaskets as sealing members will allow a slight misalignment in piping when using compression fittings
• Other pipe threads are available on request
• Installation/maintenance instructions are included with each valve
• Spare parts kits and replacement coils are available

DIMENSIONS (mm), WEIGHT (kg)

A F
A F B G
B G C
C
360

360
H
H K K
J J

IN
D
E D
E

Fig. 1: Threaded pipe connection - aluminium Fig. 2: Compression type fitting - aluminium

Availability, design and specifications are subject to change without notice. All rights reserved.

Fig. 3: Threaded pipe connection - stainless steel

catalogue number A B C D E F G H J K weight (1) (C)

SC(DU)G353A043 75 45 27 51 89 75 39 92 113 130 0,70 Fig. 1
SC(DU)G353A044 75 45 27 51 89 75 39 92 113 130 0,65 Fig. 1
DP14240GB-2012/R01

SC(DU)G353-052 75 45 27 81 125 75 39 92 175 195 0,85 Fig. 2

SC(DU)G353-053 75 45 27 81 125 75 39 92 175 195 0,90 Fig. 2
SC(DU)G353A132 75 45 27 51 89 75 39 92 113 130 1,30 Fig. 3
SC(DU)G353A133 75 45 27 51 89 75 39 92 113 130 1,20 Fig. 3
(1) Incl. coil and connector (C) Construction type
All leaflets are available on: www.asconumatics.eu
X003-8
 PULSE VALVES 2/2
NC Series
dual stage, integral pilot
threaded body 1 1/2 to 3 or IN
353
compression fitting Ø 1 1/2
FEATURES
● The diaphragm pulse valves are especially designed for dust collector service
applications, combining high flow, long life and extremely fast opening and closing
to produce reliable and economical operation
● Integral compression fittings for fast, easy, secure installation

● The high quality diaphragms are reinforced and wear resistant to guarantee a long
operating life, even under harsh conditions
• The integral operators are provided with epoxy moulded F-class coils. Various
optional waterproof and explosionproof solenoids for use in potentially explosive
atmospheres (gas & dust) according to Directive ATEX 94/9/EC can be mounted
on the same basic valve (see pages 49 to 57)
• The valves satisfy all relevant EC directives

GENERAL
Differential pressure (PS) 0,35 - 8,5 bar [1 bar = 100kPa]
Ambient temperature range -20 to +85°C
fluids () temperature range (TS) diaphragm ()

Luft -20 to +85 °C CR

MATERIALS IN CONTACT WITH FLUID

() Ensure that the compatibility of the fluids in contact with the materials is verified
Body Aluminium / Stainless steel 316L
Core tube Stainless steel
Core and plugnut Stainless steel
Core spring Stainless steel
Sealings & disc NBR (nitrile)
Diaphragm CR (chloroprene)
Shading coil Copper
Coil insulation class F
Connector Spade plug (cable Ø 6 - 10 mm)
Connector specification ISO 4400
Electrical safety IEC 335
ELECTRICAL CHARACTERISTICS
Standard voltages DC (=): 24V
(Other voltages and 60 Hz on request) AC (~): 24V - 115V - 230V / 50 Hz
nominal power ratings operator
coil inrush holding hot/cold temperature IN
protection
type ~ ~ = range (TS)
(VA) (VA) (W) (W) (°C)
CM6-FT 34 15,6 6 - IP65/IP67
CM6-FT (1) - 14 / 20,8 IP65/IP67
-20 to +85
CMXX-FT 55 23 10,5 - ATEX-NF
Availability, design and specifications are subject to change without notice. All rights reserved.

CMXX-FF - - - 14 / 19,7 ATEX-NF

(1) Intermittent duty, Relative Duty Time is 10%. Max. on time is 1 min.

SPECIFICATIONS
operating pressure
flow differential (bar) prefix optional solenoids
pipe orifice catalogue
coefficient
size size max. (PS) number
Kv
FPM

min. air () ATEX

G (mm) (m³/h) (l/min) ~/= SC WP SCDU WP(T)DU NF aluminium stainless steel 316L
G - Threaded pipe connection
1 1/2 52 44 733 0,35 8,5 l l l l l G353A047 G353A134(1) V
2 66 77 1290 0,35 8,5 l l l l l G353A050 - V
2 1/2 66 92 1540 0,35 8,5 l l l l l G353A051 - V
3 76 170 2833 1 6 l l l l l G353.060(1) - V
Ø - Compression fitting pipe connection
1 1/2 52 44 733 0,35 8,5 l l l l l G353A065(2) - V
DP14241GB-2012/R01

l : Available feature
(1) Contains spring above the main diaphragm (2) Threaded pipe connection is external (male thread)

All leaflets are available on: www.asconumatics.eu

X003-9
 SOLENOID VALVES SERIES 353

OPTIONS
• Waterproof enclosure with embedded screw terminal coil according to protection class IP67, CEE 10
• Explosionproof solenoids for hazardous locations according to ATEX and national standards
• IECEx certifcation
• Hose connection executions (3" only)
• Compliance with “UL” standards
• Plug with visual indication and/or peak voltage suppression
• Electronic timer
• Valves can also be supplied with FPM (fluoroelastomer) diaphragms and seals. Use the appropriate optional suffix letter for
identification

INSTALLATION
• The valves can be mounted in any position without affecting operation
• Threaded pipe connection is G (ISO 228/1) or compression fitting
• For compression fitting types tightness is achieved by the compressed gasket on the blow tube
• The use of the rubber gaskets as sealing members will allow a slight misalignment in piping when using compression fittings
• Other pipe threads are available on request
• Installation/maintenance instructions are included with each valve
• Spare parts kits and replacement coils are available

DIMENSIONS (mm), WEIGHT (kg)

360

360

Fig. 1: Threaded pipe connection - aluminium Fig. 2 Compression type fitting - aluminium

360°

Availability, design and specifications are subject to change without notice. All rights reserved.

Fig. 3: External threaded type - aluminium Fig. 4: Threaded pipe connection - stainless steel

catalogue number A B C D E F G H J K L weight (1) (C)

SC(DU)G353A047 80 50 30 71 130 136 45 G 3/8 131 161 178 1,4 Fig. 1
SC(DU)G353A050 80 50 30 95 168 165 45 G 3/4 165 210 227 2,9 Fig. 1
DP14241GB-2012/R01

SC(DU) G353-051 80 50 30 95 168 165 45 G 3/4 165 210 227 2,6 Fig. 1
SC(DU) G353-060 80 50 30 143 240 192 45 G 1/2 165 258 275 4,1 Fig. 2
SC(DU)G353A065 80 50 30 117 177 136 45 G 3/8 131 225 242 1,75 Fig. 3
SC(DU)G353A134 80 50 30 71 130 136 45 G 3/8 131 161 178 2,5 Fig. 4
(1) Incl. coil and connector (C) Construction type
All leaflets are available on: www.asconumatics.eu
X003-10
 POWER PULSE 2/2
Series
TANK SYSTEM (Ø160) NC 355
integral pilot
1
FEATURES
● Power Pulse Tank System using aluminium profile and end covers with CE ap-
proval according to Directive 97/23/EC for Pressure Equipment
● Full immersed valve system with special springless piston/diaphragm design
offers highest peak pressure and best flow performance operating features requi-
red for dust collector applications
● The high quality TPE piston/diaphragm guarantees a long operating life and a large
temperature range
● Possibility to apply different combinations of pitch distances and upto 24 valves
● Easy to connect to other tank systems. Service connections for different accesso-
ries such as: filter regulator, pressure gauge, safety valve and automatic/manual
drain valve
● Several blow pipe connections available, such as: Quick Mount, push-in, hose or
threaded
● Built-in silencers reduce the noise and prevent foreign particles from entering the
valve
• The integral operators are provided with epoxy moulded F-class coils. Various
optional waterproof and explosionproof solenoids for use in potentially explosive
atmospheres (gas & dust) according to Directive ATEX 94/9/EC can be mounted
on the same basic valve (see pages 49 to 57)

GENERAL
Differential pressure (PS) 0,3 to 8,5 bar [1 bar = 100 kPa]
Ambient temperature range -20°C to +85°C
Tank System
volume 0,20 dm3 per cm tank
recommended min. tank volume 10 dm3 (equals to 500 mm tank length)
min. pitch distance 120 mm
maximum length 3000 mm
min. pulse time 50 ms

fluid temperature range (TS) piston/diaphragm

air -20 to +100 °C TPE (thermoplastic polyester elastomer)

CONSTRUCTION
Tank Anodized aluminium
Adapter/body Aluminium
Clipring Stainless steel
Clamps Stainless steel
Bolts (clamps) Stainless steel
Core tube Stainless steel
Availability, design and specifications are subject to change without notice. All rights reserved.

Core and plugnut Stainless steel

Core spring Stainless steel
Sealings & disc NBR (nitrile)
Piston/diaphragm TPE (thermoplastic polyester elastomer)
Shading coil Copper
Coil insulation class F
Connector Spade plug (cable Ø 6 - 8 mm)
Connector specification 3 x DIN 46244
Electrical safety IEC 335

ELECTRICAL CHARACTERISTICS
Standard voltages DC (=) 24V
(Other voltages and 60 Hz on request) AC (~) 24V - 115V - 230V/50Hz

nominal power ratings ambient

coil inrush holding hot/cold temperature
protection
type ~ ~ = range
(VA) (VA) (W) (W) (°C)
CM22-FT 14,5 11 6,3 - -20 to +85 moulded IP65
X003GB-2009/R8

CM22-F I (1) - - - 15/22 -20 to +85 moulded IP65

(1) Intermittent duty, Relative Duty Time is 10%. Max. on time 1 min.

All leaflets are available on: www.asconumatics.eu

X003-11
 VALVES SERIES 355
SPECIFICATIONS
operating pressure differential
flow
pipe orifice (bar)
coefficient coil type catalogue
size size maximum (PS)
Kv number
min. air
(mm) (m3/h) (l/min) ~ = ~ =

1" 25 23 384 0,30 8,5 8,5 CM22-FT CM22-FI . . E355A . . .

ORDERING INFORMATION - for example: SC E355A J 06 (Specify Voltage/Hz) + Dimension code (specified on next page)

SC (DU) E 3 5 5 A J 0 6 (1)
64
52
r q 17
IEC 335/IP65 (II 3 D)

Quick Mount with clamps (Ø 33,2-34,2)

WP (WPDU)

r q K 64
52
IEC 335/IP67 (II 3 D) 37

Push-in connection (Ø 33,2-34,2)

NF

r q
II 2 G Ex d IIC, II 2 D Ex td A21IP67 (2)
L
37
9

EM Male hose connection (Ø 33,5-33,9)

Availability, design and specifications are subject to change without notice. All rights reserved.
r q
II 2 G Ex e mb II, II 2 D Ex tD (2)

M
34
9
PV
Male threaded connection (R1")

r q
II 2 G Ex mb II, II 2 D Ex m D21(2)

EF
X003GB-2009/R8

Type 7 and 9
(1)
Specify required number of valves between 01 and 24
(2)
Exact temperature class depends on wattage and max. ambient temperature (see also page 48 to 56)

All leaflets are available on: www.asconumatics.eu

X003-12
 VALVES SERIES 355

ORDERING INFORMATION DIMENSION CODE

Start distance A (min. 110 mm)
Standard pitch B/C/D (min. 120 mm)
Deviating pitch B/C/D (min. 120 mm)
End distance A (min. 110 mm)

Example I: Dimension code for a 4 valves tank system:

Operator SC, 24V/DC

Connection Quick Mount
Number of valves 4 pcs
Start and End distance 110 mm
Standard pitch 120 mm
Deviating pitch Between valve 2 and 3 is position C (see fig. 2); 150 mm
Catalogue number SC E355AJ04 24V/DC
Dimension code 110120C150
Complete order number SC E355AJ04 24V/DC + 110120C150

Example II: Dimension code for a 8 valves tank system:

Operator SC, 230/50

Connection Thread
Number of valves 8 pcs
Start and End distance 150 mm
Standard pitch 160 mm
Deviating pitch Between valve 2 and 3, 4 and 5, 6 and 7 is position C, E and G; 200 mm
Catalogue number SC E355AM08 230/50
Dimension code 150160CEG200
Complete order number SC E355AM08 230/50 + 150160CEG200

For assistance please consult our website: www.asconumatics.eu 90

DIMENSIONS (mm), WEIGHT (kg) Fig. 1 (front view)

36

Pressure
supply
G1"
325
268
145
Service
Availability, design and specifications are subject to change without notice. All rights reserved.

connection
G¼" 140
Fig. 2 (side view) 78
38

52 35 110
22 180

217
174
Ø45
X003GB-2009/R8

46,5

A B C D A

All leaflets are available on: www.asconumatics.eu

X003-13
 VALVES SERIES 355/353
OPTIONS
● Special customized executions
● Waterproof enclosures with embedded screw terminal coil according to protection class IP67, CEE 10
● Explosionproof solenoids for hazardous locations according to "ATEX" and national standards
● Explosionproof and watertight solenoids according to "NEMA" standards
● Separate Quick Mount clamps for outlet connection; kit number: C132-679

INSTALLATION
● Tank system can be mounted in any position using the standard brackets integrated in the end cap (M12 bolts
recommended) without affecting operation
● Pipe connection identifier is: R = according to ISO 7/1, G = according to ISO 228/1 or Ø for other outlet connections
● For Quick Mount types tightness is achieved by the O-ring sealing on the pipe (1" = Ø33,2 to 34,2) according to ISO 4200
● Installation/maintenance instructions and declaration of conformity are included with each tank system
● Spare valves, spare parts kits and coils are available

SEPARATE / SPARE POWER PULSE VALVES

FEATURES - (same as for the tank system)
DIMENSIONS (mm), WEIGHT (kg)

100

166

Ø 99 G1"

SPECIFICATIONS Availability, design and specifications are subject to change without notice. All rights reserved.

pipe standard catalogue ATEX dust II3D weight (1)

size catalogue number catalogue number
(G) Female threaded connection (ISO 228/1)

1" SC E353A237 SCDU E353A237 0,558

(1) = incl. coil and connector

X003GB-2009/R8

All leaflets are available on: www.asconumatics.eu

X003-14
 ALUMINIUM TANK SYSTEM 2/2
Series
8" (Ø200) 355B
NC

FEATURES
● Tank system using aluminium profile and end covers with CE approval according
to Pressure Equipment Directive 97/23/EC, modules B1+D
● For use in dust collector applications requiring high flow capacity and accurate

process control
● Full immersed valve system with polychloroprene (CR) diaphragm design offers

highest peak pressure and best flow performance

● The high quality polychloroprene (CR) diaphragm guarantees a long operating life
and a large temperature range
● Possibility to apply different combinations of pitch distances and up to 18 valves

● Easy to connect to other tank systems. Service connections for different accessories
such as: filter regulator, pressure gauge, safety valve and automatic/manual drain
valve
● Several blow pipe connections available, such as: Quick Mount, push-in, hose or

male or female threaded

● Tanks are available in a direct control valve version with a selection of coil systems
and voltages or as a remote control, single or double diaphragm version for external
pilot valves or pilot boxes
● The integral operators are provided with epoxy moulded F-class coils. Various

optional explosionproof solenoids for use in potentially explosive atmospheres

according to Directive ATEX 94/9/EC, Zones 21+22 can be mounted

GENERAL
Pressure inlet connection ISO 228/1, G 1 1/2" female
Air operating pressure min. 1,0 max. 8,0 bar
Safety pressure 12,2 bar
Flow rate Kv 43,3 = 724 l/min
Ambient temperature range -20°C to +85°C
Tank System
volume 0,314 dm3 / cm
recommended min. tank volume 15 dm3
min. pitch distance end cap 110 mm for bracket 120 mm;
between valve 160 mm
maximum length 3000 mm
The tank system can be mounted in any position without affecting operation
fluids temperature range (TS) diaphragm
air -20 to +100 °C CR (polychloroprene)

CONSTRUCTION
Tank Anodised aluminium profile EN AW-6060 T66
Valve, outlet adapter Die-cast aluminium GD-ALSi12 to EN 1706
End caps Die-cast aluminium GD-ALSi12 to EN 1706
Spring Stainless steel
Availability, design and specifications are subject to change without notice. All rights reserved.

Plugs PA (polyamide)
Sealings & disc NBR (nitrile)
Screws Steel 8.8
Diaphragm CR (optionally FPM or TPE)
Mounting brackets stainless steel AISI 304 (1.4301)
Shading coil Copper

ELECTRICAL CHARACTERISTICS
Coil insulation class F
Connector Spade plug (cable Ø 6-10 mm)
Connector specification 3 x DIN 46244
Electrical safety IEC 335
Standard voltages DC (=) : 24V
(Other voltages and 60 Hz on request) AC (~) : 24V - 120V - 230V / 50 Hz
nominal power ratings operator
coil inrush holding hot/cold temperature
protection
type ~ ~ = range (TS)
(VA) (VA) (W) (W) (°C)
DP14258GB-2013/R01

CMXX-FT 55 23 10,5 -
-20 to +85 moulded IP65
CMXX-FF - - - 14 / 19,7

All leaflets are available on: www.asconumatics.eu

DP14258-1
 TANK SYSTEM SERIES 355B

ALUMINIUM TANK SYSTEM

HOW TO ORDER
15-DIGIT PRODUCT CODE
G 355 B 8 M B S 0000 F1
Thread connection Voltage - class
G = ISO 228/1 F1 = 24 DC - Class F
FL = 24/50 - Class F
Product series FH = 230/50-60 - Class F
355 F2 = 120/60 - Class F
00 = All remote valves no voltage required

Revision letter Dimensions and option code

B Consult our Dynamic Product Modeling Tool on: www.asconumatics.eu
Mounting brackets (2 or 3) depending on total weight
Silencer for double stage valves
Diameter code / diaphragm material Pitch/dimensions
8 = 8" / Polychloroprene (CR) Dimension code for distance between valves, end caps and
F = 8" / Fluoroelastomer (FPM) mounting brackets is determined by ASCO
C = 8" / Thermoplastic polyester elastomer (TPE)
Only for single stage remote version

Outlet connection type Actuation

K = Push-in with clamps 1 = Remote single stage prepared for pilot box,
W = Push-in without clamps incl. brackets; push in fittings; plastic tube
U = Male hose connection 2 = Remote double stage prepared for pilot box,
M = Male thread connection incl. brackets; push in fittings; plastic tube
F = Female thread connection 3 = Remote control single stage
4 = Remote control double stage
5 = Remote single stage prepared for pilot box ATEX II G/D
Number of valve stations 6 = Remote double stage prepared for pilot box ATEX II G/D
1 = 1 7 = Remote control single stage ATEX II G/D
... ... 8 = Remote control double stage ATEX II G/D
A = 10 S = Solenoid operators SC IP65 ISO 4400
B = 11 D = Solenoid operators SG ATEX 3D
C = 12 N = Solenoid operators NF ATEX 2G/D
D = 13 E = Solenoid operators EM ATEX 2G/D
E = 14 P = Solenoid operators PV ATEX 2G/D
F = 15 F = Solenoid operators EF NEMA 7+9 ICS-6 ANSI
G = 16 For more technical information see catalogue page "OPERATORS"
H = 17
J = 18

Availability, design and specifications are subject to change without notice. All rights reserved.
OUTLET CONNECTION TYPES

K = Push-in with clamps W = Push-in without clamps U = Male hose connection M = Male thread connection F = Female thread connection

SPARE PARTS KITS

designation spare parts kit no.
Double remote operated valve C113826
DP14258GB-2013/R01

Solenoid operated valve C113827

Spare parts for valve sealings M200336A00
Spare parts kit for pilot box mounting brackets M200337A00

All leaflets are available on: www.asconumatics.eu

DP14258-2
 VALVES SERIES 355B

ORDERING INFORMATION

DIMENSIONS (mm), WEIGHT (kg), VOLUME (l)

Solenoid operated valve system

including spade plug connector ISO 4400, IP65, IEC 335

Fig. 1 (front view) Fig. 2 (side view)

Pressure
supply

Optional

Service
connection A P1 P2 P3 P4 B
-1,0 mm ±0,5 mm ±0,5 mm ±0,5 mm ±0,5 mm -1,0 mm

Example I: Dimension code for a 5 solenoid operated valve 24 DC tank system with push-in outlet:
Start distance A = 125 mm
Standard pitch P = 1+2+3+4 = 175 mm
End distance B = 125 mm
Total dimension 950 mm
Weight 27 kg
Volume 26 l
Order number G355B8W5S0015F1
Availability, design and specifications are subject to change without notice. All rights reserved.

For assistance please consult our website: www.asconumatics.eu

DP14258GB-2013/R01

All leaflets are available on: www.asconumatics.eu

DP14258-3
 VALVES SERIES 355B

ORDERING INFORMATION

DIMENSIONS (mm), WEIGHT (kg), VOLUME (l)

Remote double staged operated valve system prepared for pilot box
including pilot box mounting brackets, push-in fittings and tubes for G 1/8" pilot box series 110
Fig. 1 (front view) Fig. 2 (side view)

Space for:
190 mm for 6 pilot valve box
328 mm for 12 pilot valve box

Optional

Pressure
supply

Service
connection A P1 P2 P3 P4 P5 B
-1,0 mm ±0,5 mm ±0,5 mm ±0,5 mm ±0,5 mm ±0,5 mm -1,0 mm

Example II: Dimension code for a 6 double remote operated valve tank system prepared for pilot box with clamp outlet:

Start distance A = 137 mm

Standard pitch P = 1+2+4+5 = 190 mm
Deviating pitch P = 3 = between valve 3 and 4 = 260 mm
End distance B = 137 mm
Total dimension 1294 mm
Weight 34 kg
Volume 37 l
Order number G355B8K62001600

Availability, design and specifications are subject to change without notice. All rights reserved.
For technical information on ASCO pilot boxes see catalogue series 110
For assistance please consult our website: www.asconumatics.eu

OPTIONS
● Special customised executions
● Valve can be supplied with FPM (fluoroelastomer) and TPE (thermoplastic polyester elastomer) diaphragms.
● Waterproof enclosures with embedded screw terminal coil according to protection class IP67, CEE 10
● Explosionproof solenoids for hazardous locations according to "ATEX" and national standards
● Explosionproof and watertight solenoids according to "NEMA" standards
● Separate Quick Mount clamps for outlet connection; kit number: C117-290

INSTALLATION
● The tank system can be mounted in any position using the standard brackets (M8 bolts recommended) without affecting
operation.
● Pipe connection identifier is: G = according to ISO 228/1 and ISO 7/1, or Ø for other outlet connections
● For Quick Mount types tightness is achieved by the O-ring sealing on the pipe (1 1/2" = Ø47,8 to 48,8) according to
ISO 4200.
● When connecting piping or tubing to the G 1/8" or G 1/4” connection in the valve bonnet, the remote ASCO pilot valve should
be mounted as close as possible to the main pulse valve. Connection tubing lengths of 3 meters or less have little effect on
DP14258GB-2014/R01

the pulse response. Installations with over 3 meters of tubing must be tested under actual operating conditions. Tubing with
Ø6 or Ø8 mm O.D. is recommended for all installations.
● Installation/maintenance instructions and declaration of conformity are included with each tank system.
● Spare parts kits and coils are available.

All leaflets are available on: www.asconumatics.eu

DP14258-4
 TANK SYSTEM 2/2
Series
(Ø 8")
integral pilot
NC 357
1 1/2
FEATURES
• Immersion tank system using steel profile and welded end covers with CE ap-
proval according to Directive 87/404/EC
• Immersed valve system with special diaphragm design offers highest peak pres-
sure and best flow performance operating features required for dust collector
applications
• The high quality diaphragms are reinforced and wear resistant to guarantee a
long operating life, even under harsh conditions
• Possibility to apply different combinations of pitch distances
• Service connections for different accessories such as: filter regulator, pressure
gauge, safety valve and automatic/manual drain valve
• Available with hose and threaded blow pipe connections
• The integral operators are provided with epoxy moulded F-class coils

General
Differential pressure (PS) 0,35 to 8 bar [1 bar = 100kPa]
Ambient temperature range -10 to +80°C

fluid temperature range (TS) seal materials

air -10 to +80°C CR (chloroprene)

CONSTRUCTION
Tank Steel, grey
Bonnet Aluminium
Bolts Stainless steel
Core tube Stainless steel
Core and plugnut Stainless steel
Spring Stainless steel
Sealing & discs NBR (nitrile)
Diaphragm CR (chloroprene)
Shading coil Copper
Coil insulation class F
Connector Spade plug (cable Ø 6-10mm)
Connector specification ISO 4400
Electrical safety IEC 335

ELECTRICAL CHARACTERISTICS
Standard voltages DC (=) : 24V - 48V;
(Other voltages and 60 Hz on request) AC (~) : 24V - 48V - 115V - 230V / 50Hz

nominal power ratings

inrush holding hot/cold
coil type protection
~ ~ =
(VA) (VA) (W) (W)
Availability, design and specifications are subject to change without notice. All rights reserved.

CMXX-FT 55 23 10,5 -
moulded IP65
CMXX-FT - - - 14 / 19,7

SPECIFICATIONS
operating pressure
pipe orifice flow coefficient differential (bar)
catalogue number
size size Kv max. (PS)
min air
(mm) (m3/h) (l/min) ~/= hose threaded
8" Tank System
1 1/2" 40 46 768 0,35 8 SCG357ANxx (1) (2) SCG357AOxx (1) (2)
(1)
Standard tank has round ends. For flat ends use suffix FE
(2)
xx indicates the number of valves
X003GB-2014/R01

All leaflets are available on: www.asconumatics.eu

X003-15
 TANK SYSTEM SERIES 357

ORDERING
Example: Dimension code for a 4 valves tank system: ORDERING EXAMPLE TANK SYSTEM:
Tank diameter 8" SCG357AN 04 (*)
24 V/DC + 170 180 D200
Operator SC, 24V/DC
Pipe size 1 1/2" deviating pitch
Connection Hose (see fig. 1: Connection Type)
standard pitch
Number of valves 4 pcs
Start and End distance 170 mm start & end dist.
Standard pitch 180 mm voltage
Deviating pitch Between valve no. 3 and no. 4 tank end type
is position D (see fig. 1) 200 mm no. of valves
Catalogue number SCG357AN04 24V/DC catalogue no.
Dimension code 170180D200

SPARE PARTS KITS

spare parts kit no.
catalogue number
~/=
SCG357ANxx
C113827
SCG357AOxx

DIMENSIONS (mm)
A B C D A A
HOSE THREADED
G G
CERT. PLATE
F
F

F
ØE

80

80
40
ØH
1/4" GAS FEMALE (3x) Flat ends (Suffix "FE")
Fig.1
F
Connection Type

A B/C/D A
tank min. start distance minimum pitch min. end distance
fig. ØE F G Ø H
diameter
(round) (flat) (round) (flat) (round) (flat)
8" 1 170 118 160 160 170 118 218,1 G 1 1/2" 70 18 48,3
() For standard tank (round ends) use no suffix, for flat ends use suffix FE

Availability, design and specifications are subject to change without notice. All rights reserved.
MOUNTING BRACKETS E
Ø13
C
E
H

G
B

Ø13
H
G

F Ø13 F D
C
Fig.2 - Contra bracket Fig.3 - Bracket
tank tank
fig. C ØE F G H fig. B C D ØE F G H
diameter diameter
8" 2 348 284 50 8 110 8" 3 210 348 200 284 50 8 110

INSTALLATION
• Tank System can be mounted in any position. We can supply standard mounting brackets with each tank by specifying suffix
X003GB-2014/R01

MB behind the catalogue number (see figure 2 and 3)

• Installation / maintenance instructions and declaration of conformity are included with each tank system
• Spare part kits and coils are available

All leaflets are available on: www.asconumatics.eu

X003-16