Beer'S Law Laboratory Experiment/ Simulation

BEER’S LAW LABORATORY EXPERIMENT/ SIMULATION
Name Date
Objectives
1. Explain the difference between the transmittance and absorbance of light.
2. Describe the relationship between observed color and light absorbance.
3. Determine the wavelength of maximum absorbance (ƛmax).
4. Describe what happens to the absorbance of light by a solution when the concentration of the
solution is increased or decrease.
5. Describe what happens to the transmittance of light by a solution when the concentration
of the solution is increased or decreased.
6. Determine the relationship between the concentration and the absorbance at maximum
wavelength of absorbance (ƛmax).
7. Determine the relationship between the concentration and the transmittance at ƛmax.
8. Use the Absorbance vs. Concentration plot to determine the molar absorptivity and the
concentration on an unknown colored solution.
9. Predict how the intensity of light absorbed/transmitted will change with changes in solution
type, solution concentration, container width, or light source, and explain why.
Procedure
Explore the controls in the Beer’s Law screen for a few minutes
Note: A spectrophotometer measures the amount of light absorbed by a sample in comparison to the
amount emitted by the light source. In this tab, you can investigate how a UV-Vis spectrometer
functions. When a solution becomes more concentrated, it looks darker (the color intensity increases). A
spectrophotometer allows you to measure and quantify this phenomenon.
1. Absorbance vs Transmittance
1.1. Explore the differences between absorbance and transmittance (online sources) and
answer question 1.
2. Relationship between observed color and light absorbance.

2.1. On the Beer’s Law screen, select “Drink Mix” as the solution. Set wavelength to “preset”.
Turn on light source. Record the color of the solution, color of the light beam and the
wavelength in “Data Table 2”.
2.2. Repeat above for remaining solutions and complete the data table 2.
2.3. Compare data you’ve entered into Data Table 2, with Figure 1 (Color Wheel) and Table 1
of the introduction, write your answer to question # 2 (Post Simulation: Evidence
Reasoning section).
Data Table 2.
Relationship of observed color to color absorbed (Complement colors).
Solution Color of the solution Color of the light beam at Wavelength at maximum
maximum absorbance absorbance
Drink Mix
Co(NO3)2
CoCl2
K2Cr2O7
K2CrO4
NiCl2
CuSO4
KMnO4
Co(NO3)2
3. Determine the wavelength of maximum absorbance (ƛmax).

3.1. Select “KMNO4: Potassium Permanganate” for the solution.
3.2. Set wavelength to “Variable”. Move the slider to set wavelength to 400 nm. Drag and position the
probe in path of the light beam. Record absorbance and transmittance readings displayed on the
meter. Complete row 1 of the Data Table 3 with absorbance and transmittance values you
obtained.
3.3. Repeat above step for indicated 50nm increments of the wavelength settings and complete the Data
Table 3.
Data Table 3.
Absorbance vs. Transmittance Data for KMNO4 solution ( µM)
Wavelength (nm) Absorbance Transmittance
400
450
500
550
600
650
700
750
4. Absorbance Vs Solution Concentration.
4.1. Move the rule below the Cuvette and make sure that the width of the cuvette (Path Length) is
1 cm.
4.2. Set the KMNO4 concentration to 50 µM.
4.3. Turn on the light source and move the probe into light path.
4.4. Select Wavelength “Preset”. Wavelength (ƛmax) is indicated as 544 nm. We are measuring
Absorbance for solutions of varying concentrations at ƛmax.
4.5. Record absorbance value at KMNO4 concentration 50 µM and enter the value on Data Table 4.
4.6. Change the concentration to 100 µM and record absorbance value on Data Table 4.
4.7. Complete the table for remaining wavelengths.
Data Table 4.
KMNO4 concentration (µM) Vs. “Absorbance” of light.
KMNO4 concentration (µM) Absorbance
50
100
200
300
400
500
600
700
750
5. % Transmittance Vs Solution Concentration.

5.1. Select the meter to collect Transmittance data.
5.2. Repeat steps of procedure 4 above and complete Data Table 5 for % Transmittance of light.
Data Table 5.
KMNO4 concentration (µM) Vs. “% Transmittance” of light.
KMNO4 concentration (µM) Transmittance (%)
50
100
200
300
400
500
600
700
750
Post –Simulation: Evidence and Reasoning
1) Explain the difference between the transmittance and absorbance of light.
2) How does the color absorbed related to observed color of the solution (Compare data from Data Table 2
to Figure 1 of the “Introduction” section to justify your answer?
3) Investigate the green light passing through the KMnO4 solution and graph your results. When KMnO4
was used as the solution, light source directs green light through the solution.
a. Where the green light is more intense?
b. Where the green light is least intense?
c. Where does the intensity of light changing?
4) Refer to Data Table 4 in which you entered Absorbance values for varying concentrations of KMNO4
solution. What happens to the absorbance when the concentration is doubled?
5) What is the ƛmax KMnO4 solution?

REFERENCE:
Chamberlain, J., & Clark, T. (2015, June 23). Beer's Law Lab. Retrieved
November 11, 2017, from http://phet.colorado.edu/en/simulation/beers-law-lab
Rohrig, B. (2015, October). Artificial Dyes. Retrieved November 11, 2017, from
https://www.acs.org/content/acs/en/education/resources/highschool/chemmatters/past-issues/2015-
2016/october-2015/articial-dyes.html

Beer'S Law Laboratory Experiment/ Simulation

Uploaded by

Copyright:

Available Formats

Beer'S Law Laboratory Experiment/ Simulation

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Beer'S Law Laboratory Experiment/ Simulation

Uploaded by

Copyright:

Available Formats

BEER’S LAW LABORATORY EXPERIMENT/ SIMULATION

2. Relationship between observed color and light absorbance.

3. Determine the wavelength of maximum absorbance (ƛmax).

5. % Transmittance Vs Solution Concentration.

a. Where the green light is more intense?

b. Where the green light is least intense?

c. Where does the intensity of light changing?

5) What is the ƛmax KMnO4 solution?

You might also like