Msme Technology Centre, Durg Assesment Test: Press Tool: Name: Total Marks: Course: Total Duration: Batch

MSME TECHNOLOGY CENTRE, DURG
ASSESMENT TEST: PRESS TOOL
NAME: TOTAL MARKS:

COURSE: TOTAL DURATION:
BATCH:
ALL QUESTIONS CARRY EQUAL MARKS .THERE IS NO NEGATIVE MARKING.
Q.1) Which material is generally preferred for Die plate.

a) Mild steel b) Cast Iron
d)HCHCr e) None of the above
Q.2) The male part of press tool is….
a) Die b) Punch
d) Guide Pillar e) Top plate
Q.3) Sheet metal is defined as a thin strip of metal with at most length and width
a) 4mm b) 5mm
d) 6mm e) 8mm
Q.4) Which plate is used to hold the punch holder and guide bushes.
a) Top plate b) Punch holder plate
d) Bottom plate e) Stripper plate
Q.5) the burr side of a punched opening is towards the ___________ side
a) Punch b)Die
d) Both a & B e)None
Q.6) The intentional gap between punch and die cutting edges is…..
a) Strip margin b) Pitch
d)Land e) Die clearance
Q.7) The given below strip layout is
a) Single row double pass b) Single row single pass

c) Double row double pass d) None of these
Q.8) In one stroke of press ram if more than one similar blank produced, such die is
called
a) Simple die b) Compound die
c) Gang die d) Progressive die
Q.9) Collapsible tubes are produce by
a) Curling b) Coining
c) Extrusion d) Embossing
Q.10) Identify the strip layout
a) Angular b) Narrow
c) Single row two pass d)None
Q.11)The minimum economy should be aimed at while laying the strip is
a) 100 % b) 50 %
c) 60 % d) 80 %
Q.12)why over bending is done while V-Bending
a)to compensate the spring back b) to get the required bending
c) to get the accuracy d)all of these
Q.13)The stock strip is stripped off the --------- by the stripper
a)die b)punch
c)Pilot d)All
Q.14)The distance from a point on one part to the corresponding point on the next
part is known as
a)Pitch b)Margin
c)Scrap bridge d)Width
Q.15)Calculate strip lay out
a)To increase economy b)To decrease economy
c)No effect on economy d)None of these
Q.16)No land is provided while punching materials likes

a)Silicon steel & stainless steel b)Mild steel & cast iron
c)EN31 & OHNS d)HCHCr& P20
Q.17)Cutting clearance is calculated using the formula
A) 0.001 X T X (shear strength)1/2
b)0.01 X T X (shear strength)1/2
c)0.1 X T X (shear strength)1/2
b)0.01 X T X (shear strength)
Q.18)Double cut band occurs due to
a)Optimum cutting clearance b)Insufficient cutting clearance
c)Maximum cutting clearance d)None
Q.19)The fit between the stripper & the punch is
a)H7/g6 b)H7/p6
c)H7/k6 d)H7/m6
Q.20) which type of press action is used for drawing operation
a) single b) double
c) no required d) all of these
Q.21) Which press is used for drawing operation generally
a) hydraulic b) pneumatic
c) hydro-pneumatic d) none of these
Q.22) Match the operation with type of press
Operation type of press
1.) fine blanking a) single action
2.) drawing b) double action
3.) piercing c) Triple action
a) 1-a,2-c,3-b b) 1-b,2-c,3-a
c) 1-c,2-b,3-a d) 1-a,2-b,3-c
Q.23) Material of Punch And die
a) D2 b) HCHCr
c) OHNS d) all of these
Q.24) which types of fastener for given below
a) stripper bolts b) stripper bolts

c) socket cap screws d) all of these
Q.25) calculate size of punch of blanking operation for given component
a) 50 x 40
b) 50.12 x 40.12
c) 49.88 x 39.88
d) 49.76 x 39.88
Q.26) Identify the Tool
a) compound tool
b) Piercing tool
c) Progressive tool
d) Hole Flanging tool
Q.27) Component width + scrap bridge =................
a) Pitch
b) Front margin
c) Back margin
d) All of These
Q.28) The example of hybrid punch is
a) Forming punch
b) Lancing punch
c) Bending punch
d) Trimming punch
Q.29) Which accessories are used in die
a) Stopper
b) Pilot
c) Stripper
d) All of The above
Q.30) The unit of shear strength is ............
a) N/mm2
b) N/mm
c) N/cm
d) All of These
Q.31)Dowels are subjected to ____________stress due to horizontal force resulting

from die clearance.
a) Tensile Stress b) Shear stress
c) Compressive stress d)None
Q.32)which surface of the bending component will be subjected to compressive force
a) Outer bend surface b) Inner bend surface
c) Both surfaces (inner & outer) d)None
Q.33) Die set consist of assembly of
1) Top plate 2) Bottom plate 3) Stripper plate 4) Punch holder plate 5) Guide pillar 6)
Guide bush
a) 1, 2, 3&4 b)1, 2, 5&6
c) 2, 3, 5&6 d) 3, 4, 5&6
Q.34) Large edge radius which does not blend smoothly with cut band and the cut
band becoming smaller is a result of
a) Optimum cutting clearance b) Excessive cutting clearance
c) Insufficient cutting clearance d) none of these
Q.35) Identify the type of Die set shown in the figure below
a) Rear pillar b) Centre Pillar
c) Diagonal pillar d) Four pillar
Q.36) The tool used to perform multiple cutting operations at various stations to give
final shape of component from a sheet.
a) Compound tool b) Progressive tool
c) Combination tool d) Simple blanking tool
Q.37) Operation in which a sheet or blank is cut along a straight line. In this operation
no material wastage takes place.
a) Parting off b) Notching
d) Cutting off e) Lancing
Q.38) The force amounting to 2 kg-f is equal to
a) 9.81 N b) 20 N
c) 19.61 N d) 10 N
Q.39)The recommended minimum distance between screw and dowel hole from the
edge of the die is --------- to the diameter of the screw
a)0.5 times of diameter b)1 times of diameter
c)2 times of diameter d)1.5 times of diameter
Q.40) Match the operation with type of press
Operation type of press
1.) fine blanking a) single action
2.) drawing b) double action
3.) piercing c) Triple action
a) 1-a,2-c,3-b b) 1-b,2-c,3-a
c) 1-c,2-b,3-a d) 1-a,2-b,3-c

Msme Technology Centre, Durg Assesment Test: Press Tool: Name: Total Marks: Course: Total Duration: Batch

Uploaded by

Copyright:

Available Formats

Msme Technology Centre, Durg Assesment Test: Press Tool: Name: Total Marks: Course: Total Duration: Batch

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Msme Technology Centre, Durg Assesment Test: Press Tool: Name: Total Marks: Course: Total Duration: Batch

Uploaded by

Copyright:

Available Formats

MSME TECHNOLOGY CENTRE, DURG

ASSESMENT TEST: PRESS TOOL

NAME: TOTAL MARKS:

ALL QUESTIONS CARRY EQUAL MARKS .THERE IS NO NEGATIVE MARKING.

Q.1) Which material is generally preferred for Die plate.

a) Single row double pass b) Single row single pass

Q.16)No land is provided while punching materials likes

Q.24) which types of fastener for given below

a) stripper bolts b) stripper bolts

Q.31)Dowels are subjected to ____________stress due to horizontal force resulting

You might also like