UTC LM8560 MOS IC

DIGITAL ALARM CLOCK

DESCRIPTION
The LM8560 is alarm equipped digital clock IC with built-in
driver capable of directly driving LED display equipment. As IC
himself the VDD pin for the LM8560 is graded to withstand a
voltage of 15V.

FEATURES
*Single chip P-channel ED MOS LSI
*LED direct drive using time division (duplex configuration)
*Wide operating power supply voltage range
SDIP-28
*Built-in alarm function with 24-hour control
*Supports changeover between 12-hour AM/PM and 24-hour
displays
*Built-in battery backup CR oscillator
*Users 50Hz or 60Hz as standard frequency
*Built-in automatic fast forward function for hour and minute
settings
*Built-in sleep timer function (maximum intervals of 59 minutes
or 1 hours and 59 minutes)
*Built-in snooze function supporting repeat use
*Equipped with power failure display function
*900Hz output for alarm tone

FUNCTIONS
*Current time display
*Snooze alarm function
*Sleep timer function (maximum intervals of 59 minutes or 1
hours and 59 minutes)

APPLICATIONS
*Alarm clocks
*Clock radios

UTC UNISONIC TECHNOLOGIES CO., LTD. 1

QW-R502-005,D
UTC LM8560 MOS IC
PIN CONFIGURATIONS

AM& 10'S HR 1 28 12/24 HR Select

ag&de

PM& 10'S HR b 2 27 CR Input

10'S HR c& HR e 3 26 50/60 Hz Select

HR b&g 4 25 50/60 Hz Input

HR c&d 5 24 Snooze Input

HR a&f 6 23 Sleep Display

10'S MIN a&f 22 Hour Set

7
LM8560
10'S MIN b&g 8 21 Minute Set

10'S MIN c&d 9 20 VDD

10'S MIN e &Min e 10 19 Alarm Display

MIN b&g 11 18 Alarm OFF

MIN c&d 12 17 Sleep Output

MIN a&f 13 16 Alarm Output

Colon Output 14 15 VSS

ABSOLUTE MAXIMUM RATINGS (Ta=25°C, Vss=0V)

PARAMETER SYMBOL TEST CONDITIONS RATING UNIT
Maximum Supply Voltage VDD (max) -15~ +0.3 V
Input Voltage1 VIN1 50/60Hz Input -15~ +0.3 V
Input Voltage2 VIN2 Except 50/60Hz Input -15~ +0.3 V
Output Voltage VOUT -15~ +0.3 V
Input Clamp Current lIN 50/60Hz Input -0.4 ~+0.4 mA
Allowable Power Dissipation PD (max) Ta=70°C 700 mW
Operating Temperature Topr -30 ~ +70 °C
Storage Temperature Tstg -55 ~ +125 °C

ALLOWABLE OPERATING RANGES (Ta=25°C, Vss=0V )

PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT
Supply Voltage VDD -14 -7.5 V
Input “H” Level Voltage1 VIH1 50/60Hz Input -1 V
Input “L” Level Voltage1 VIL1 50/60Hz Input VDD+2 V
Input “H” Level Voltage2 VIH2 Except 50/60Hz Input -1.5 V
Input “L” Level Voltage2 VIL2 Except 50/60Hz Input VDD+2 V
50/60Hz Input Pin Input VAC-IN Sets VSS as Reference VLED V
Voltage

UTC UNISONIC TECHNOLOGIES CO., LTD. 2

QW-R502-005,D
UTC LM8560 MOS IC
ELECTRICAL CHARACTERISTICS (Ta=25°C, VDD=-12V unless otherwise specified)
PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT
Input “H” Level Current 1 IIH1 50/60Hz Input, VIN=VSS 10 µA
Input “L” Level Current 1 IIL1 50/60Hz Input, VIN=VDD 10 µA
Input “H” Level Current 2 IIH2 Input Pins Other Than 50/60Hz Input 20 µA
VIN=VSS
Input “L” Level Current 2 IIL2 Input Pins Other Than 50/60Hz Input 10 µA
VIN=VDD
Output “H” Level Current 1 IOH1 Alarm Output and Sleep Output 5 mA
VOH=VSS-1V
Output Leakage Current 1 IOF1 Alarm Output and Sleep Output 10 µA
VOUT=VDD
Output “H” Level Current 2 IOH2 AM & 10’S HR ag & de (24H mode) 36 mA
VOUT=VDD-1V
Output Leakage Current 2 IOF2 AM & 10’S HR ag & de (24H mode) 20 µA
VOUT=VDD
Output “H” Level Current 3 IOH3 Segment Output Other Than Those 18 mA
VOUT=VSS-1V
Output Leakage Current 3 IOF3 Segment Output Other Than Those 20 µA
Listed Above, VOUT=VDD
Power failure detection VDD -7.5 -5 V
Voltage
Consumption Current ICC Output set to off and Pull-down attached 5 7 mA
input set open
Backup Oscillator Stability FS Standard Value,900Hz, -10 10 %
Factor VDD=-9V±10%-10
Backup Oscillator FA Standard Value,900Hz, VDD=-9V-10 -10 10 %
Accuracy

DESCRIPTION OF OPERATIONS
*50/60Hz Input:
Built-in Shumidt circuit enables noise eliminations at 50/60Hz commercial frequencies with use of a
simple CR filter. Built-in pull-up resistor.
*CR Input:
When the AC power supply is interrupted, the time counter switches to a holding state and a built-in
oscillator promptly begins operation. If 50/60Hz input continues for 3 clocks without arriving, this
oscillator’s output is activated and functions as the time counter clock in place of 50/60Hz input. The
frequency level of this clock oscillator is determined according to the CR value. While the above
mentioned oscillator is operating using backup mode, all segment output is switched to OFF.
(Note) When the backup oscillator is in use due to an AC power supply interruption, the 50/60Hz input
pin must be maintained open or at a VSS level.
*50/60 Selective Input:
When 50/60 selective input is connected to VSS, 50Hz use is enabled. When 50/60 selective input is
left open, VDD is activated using an internal pull-down resistor and the setting is switched to enable use
at 60Hz.
*Display Mode Selective Input (Alarm Select/Sleep Select):
Since the pull-down resistor is built-in , selection from four display modes is possible using two SPST
switches (single-pole and single-throw switches). Table 1 shows these display mode selections.

UTC UNISONIC TECHNOLOGIES CO., LTD. 3

QW-R502-005,D
UTC LM8560 MOS IC
Table1 Display Modes
Selective lnput
Display Mode Digit No. 1 Digit No. 2 Digit No. 3 Digit No.4
Alarm Sleep
10’s place for 10’s place for
NC NC Time display Hour Minute
hour, AM/PM Minute
10’s place for 10’s place for
VSS NC Alarm display Hour Minute
hour, AM/PM Minute
10’s place for
NC VSS Sleep display Clear Hour Minute
Minute
10”s place for
VSS VSS Second display Clear Minute Second
Second
Note: Activating VSS using two inputs simultaneously (alarm select and sleep select), the display mode is switched to
display seconds.

*Time Setting Input:

There are two setting inputs for use with “hour” and “minute”. Time content settings show in Table2 are
possible by activating VSS to these pins, A pull-down resistor is built-in.

Table2 Setting contents

Display Mode Set Input Functions
Time Hour Immediately adds 1 to hour digits and then assigns an additional 1, at a
speed of 2 Hz, after each 1/4 to 3/4 second.
Min Immediately adds 1 to minute digits and then assigns an additional 1, at a
speed of 2 Hz, after each 1/4 to 3/4 second. Seconds are rest.
Both Operates both as outline above.
Second Hour (note1) Second digits are cleared to [00].
(Alarm & Sleep) Min Time holds.
Both (note2) Resets hour and minute digits as [0:00] when operating in 24-H mode or
[12:00] when operating in 12-H mode.
Alarm Hour Immediately adds 1 to hour digits and then assigns an additional 1, at a
speed of 2 Hz, after each 1/4 to 3/4 second.
Min Immediately adds 1 to minute digits and then assigns an additional 1, at a
speed of 2 Hz, after each 1/4 to 3/4 second.
Both Resets hour and minute digits as [0:00] when operating in 24-hour mode or
[12:00] when operating in 12-hour mode.
Sleep - Sets sleep counter to [0:59] instantly when VDD is activated to sleep select
Hour Sets Sleep counter to [1:59] instantly when VDD is activated to sleep select
and hour at the same time.
Min Sleep counter looses 1 at a speed of 2 Hz.
Both Sleep counter looses 1 at a speed of 2 Hz.
Note:1.Once conditions have been switched to reset or hold, input of other functions is locked until both Hour and
Min input have been separated.
2.When the digital reading for seconds is between 30 and 59 seconds, 1 is added to the digits for minutes as
he digital reading for seconds rests to [00].

*12/24H Select Input :

When this pin set open (VDD), a 12-hour display is enabled whereas connecting this pin to VSS enables
the 24-hour display. A pull-down resistor is build-in.
*Power Failure Detection Display :

UTC UNISONIC TECHNOLOGIES CO., LTD. 4

QW-R502-005,D
UTC LM8560 MOS IC
When activated by drop in power supply, all segments which are lit begin to blink and the unit switches
to a power failure detection display. The power failure detection display is canceled by activating VSS to
Hours set or Min set.
*Alarm Operation and Alarm Output :
The alarm signal outputs when alarm content matches the content of current time. When not rest by
either snooze input or alarm off input, output continues after 1 hour and 59 minutes. This output signal
consists of 900Hz 2Hz intermittent (50% duty) modulation signals, When the need arises , a filter can be
applied to after the alarm signal to a DC signal.
*Snooze Input :
When the alarm is sounding and instantly activating VSS to this pin , alarm output is set to OFF for a
period between 8 and 9 minutes after which time the alarm signal is once again output. The snooze
function can be used repeatedly in 1 hours and 59 minutes intervals. A pull-down resistor is built-in
Activating VSS to the snooze pin when the alarm is OFF resets the sleep timer counter to [0:00 ](This is
known as the one-touch sleep timer reset function.)
*Alarm Off Input :
Activating this input pin to VSS instantly sets alarm output to OFF.A pull-down resistor is built-in.
*Sleep Timer and Sleep Output :
Sleep output can turn on the radio and can be set for time intervals of 59 minutes or 1 hour and 59
minute. Refer to Table 2 for the proper selection procedure (59 minutes or 1 hour and 59 minute
selection.) This sleep timer is constructed using a down counter and when the counter content arrives at
[00], output is set to off and the radio turns off. Adding VSS to snooze input turns sleep output off. When
sleep output is on.

UTC UNISONIC TECHNOLOGIES CO., LTD. 5

QW-R502-005,D
 UTC
50/60 Hz 12/24 HR
Select Select
26 28
BLOCK DIAGRAM

2Hz
UTC LM8560

CR Input 27 OSC CTR 1Hz 50/60 Hz 1 AM&10'S HR ag&de

GATE 1/25 or 1/30 1/2
Tone TDisp &
50/60Hz Input 25
S.Sample PF. Blank& 2 PM&10'S HR b
50/60Hz DET Flash
Standby DET
SEC CTR GATE 3 10'S HR c&HRe

Minute Set 21 S.Sample 4 HR b&g

Input
Control Time min.CTR Time HR.CTR
Hour Set 22 F.Sample Sec
5 HR c&d
2Hz
Time&S.Sample Time&F.Sample
Reset Sec RSTYHLD Comparator 6 HR a&f
T.RST Time
Control
AL.RST

PWR UP
7 10'S MIN a&f
PWR UP
AlarmDisplay 19 SEC
T Disp Alarm MIN
Display Alarm HR CTR 8 10'S MIN b&g
CTR Alarm
Control Disp
AL Disp
Sleep Display 23 SL Disp Time&F.Sample
Output Decoder/Driver

Alarm&F.Sample 9 10'S MIN c&d

Sleep CTR Sleep
PWR 10 10'S MIN e&Min e

Display
Second
UP
Control 11 MIN b&g

Output
Snooze Input 24 12 MIN c&d
Control

13 MIN a&f

20 15 14 18 16 17
VDD VSS Colon Alarm Alarm Sleep
Output OFF Output Output

UNISONIC TECHNOLOGIES CO., LTD.

MOS IC

6
QW-R502-005,D
 C1
27k
0.015μ

UTC
f=900Hz
4.7k
R1
27k
110k
2.2k
UTC LM8560

12 HR 60 HZ 2.2k
0.47μ 4.7k

+
0.001μ NC NC
28 27 26 25 24 23 22 21 20 19 18 17 16 15

12/24 CR 50/60 50/60 Snooze Sleep Hour Minute VDD Alarm Alarm Sleep Alarm VSS
Backup HR Input Hz Hz Input Display Set Set Display OFF Output Output
Battery Select Select Input
100k

LM8560
AM&
10'S PM& 10'S 10'S 10'S 10'S 10'S
HR 10'S HR c& HR HR HR MIN MIN MIN MIN e MIN MIN MIN Colon
ag&de HR b HR e b&g c&d a&f a&f b&g c&d &Min e b&g c&d a&f Output

1 2 3 4 5 6 7 8 9 10 11 12 13 14

Duplex
LED
AC a
+ Note: 1 f b
e g c
cycle 1 d
Cathode
2
CLOCK-RADIO APPLICATION CIRCUIT (Positive Power Supply)

Common
cycle 2 This circuit is used as noise interference stripper for
the LW band.(Backup control is enalbled except for
battery backup mode

Unit(resistor:Ω , capacitor : F)

UNISONIC TECHNOLOGIES CO., LTD.

12 Hour Display and 60Hz Circuit Diagram
MOS IC

7
QW-R502-005,D
 Piezo
Buzzer

UTC
C1 R1 330μ
0.015μ +
UTC LM8560

110k

f=900Hz

0.001μ 12 HR 60 HZ
NC NC
28 27 26 25 24 23 22 21 20 19 18 17 16 15
12/24 CR 50/60 50/60 Snooze Sleep Hour Minute VDD Alarm Alarm Sleep Alarm VSS
HR Input Hz Hz Input Display Set Set Display OFF Output Output
Select Select Input
100k

LM8560
AM& PM& 10'S 10'S 10'S 10'S 10'S
10'S 10'S HR c& HR HR HR MIN MIN MIN MIN e MIN MIN MIN Colon
HR HR b HR e b&g c&d a&f a&f b&g c&d &Min e b&g c&d a&f Output
1 2 3 4 5 6 7 8 9 10 11 12 13 14
CLOCK APPLICATION CIRCUIT (Negative Power Supply)

Duplex
LED
a
AC Note: 1. f b
e g c
cycle 1 d

Cathode
Common
2. When Battery backup or tone output is not
cycle 2
used,CR input is conneced to Vss

UNISONIC TECHNOLOGIES CO., LTD.

Unit(resistor:Ω , capacitor : F)
MOS IC

8
12 Hour Display and 60Hz Circuit Diagram

QW-R502-005,D
UTC LM8560 MOS IC

UTC assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or
other parameters) listed in products specifications of any and all UTC products described or contained
herein. UTC products are not designed for use in life support appliances, devices or systems where
malfunction of these products can be reasonably expected to result in personal injury. Reproduction in
whole or in part is prohibited without the prior written consent of the copyright owner. The information
presented in this document does not form part of any quotation or contract, is believed to be accurate
and reliable and may be changed without notice.

UTC UNISONIC TECHNOLOGIES CO., LTD. 9

QW-R502-005,D