Stainless Steel Pipe System

Vic-Press® for Schedule 10S Type 304 Stainless Steel 18.12

1.0  PRODUCT DESCRIPTION

Available Sizes:
• ½ – 2"/12 – 50 mm
Maximum Working Pressure:
• 500 psi/3450 kPa
• Up to 300 psi/2065 kPa when used with Schedule 5S pipe
• FM Approved up to 175 psi/1205 kPa
Application:
• Joins ASTM A-312 Schedule 10S stainless steel pipe
Pipe or Tube Materials:
• Stainless steel
Codes and Requirements:
• Support hanger spacing correspond to ASME B31.1 Power Piping Code and ASME B31.9 Building Services
Piping Code
• Meets ASME requirements for ANSI Class 150 systems for water, oil, gases and general chemical services.

2.0 CERTIFICATION/LISTINGS

NOTES
• Refer to Victaulic submittal publication 10.01 for details.
• Refer to Victaulic submittal publication 02.06 for potable water approvals if applicable.

ALWAYS REFER TO ANY NOTIFICATIONS AT THE END OF THIS DOCUMENT REGARDING PRODUCT INSTALLATION, MAINTENANCE OR SUPPORT.

System No. Location Spec Section Paragraph

Submitted By Date Approved Date

victaulic.com
18.12 6390 Rev L Updated 01/2016 © 2016 Victaulic Company. All rights reserved.
1
victaulic.com

3.0  SPECIFICATIONS - MATERIAL

Housing Body: Made from Type 304L stainless steel.
Threaded Outlets: Made from stainless steel bar or stainless steel pipe conforming to ASTM A 312, Type 304L.
Plain End or Grooved End Products: Stainless steel pipe conforming to ASTM A 312, Type 304L.
Style P595 Flange Adapter: ANSI Class 150 or AS 2129 Table E, Type 316L raised face one-piece Type 304L
stainless steel flange adapter.
Style P565 Van Stone Flange Adapter: ANSI Class 150 or AS 2129 Table E, Carbon Steel raised face slip on flange
with Type 304 stainless steel stub end.
Style P594 Concentric Reducer: Reducer body made from Type 304 stainless steel, press ends made from Type
304L stainless steel.
Housing: Type 304 stainless steel, conforming to ASTM A 351, A 743 and A 744, Grade CF8M
Standard:
Grade “H” HNBR

HNBR (Orange stripe color code). Temperature range -20°F to +210°F/-29°C to +98°C. May be specified for hot
petroleum/ water mixtures, hyrdocarbons, air with oil vapors, vegetable and mineral oils, engine oil, transmission
oil. UL Classified in accordance with ANSI/NSF 61 for cold +73°F/+23°C and hot +180°F/+82°C potable water
service and ANSI/NSF 372.
Optional Gasket: (specify choice1)
Grade “E” EPDM
EPDM (Green stripe color code). Temperature range -30°F to +250°F/-34°C to +121°C. May be specified for cold
and hot water service within the specified temperature range plus a variety of dilute acids, oil free air and many
chemical services. UL Classified in accordance with ANSI/NSF 61 for cold +73°F/+23°C and hot +180°F/+82°C
potable water service and ANSI/NSF 372. NOT COMPATIBLE FOR PETROLEUM SERVICES. NOT COMPATIBLE
FOR STEAM SERVICES.
Grade “O” fluoroelastomer

Fluoroelastomer (Blue stripe color code). Temperature range +20°F to + 300°F/–7°C to +149°C. May be specified
for many oxidizing acids, petroleum oils, halogenated hydrocarbons, lubricants, hydraulic fluids, organic liquids
and air with hydrocarbons. NOT COMPATIBLE FOR HOT WATER OR STEAM SERVICES.
For alternate gasket selection, refer to Victaulic submittal publication 05.01.
1   ervices listed are General Service Guidelines only. It should be noted that there are services for which these gaskets are not compatible. Reference should
S
always be made to the latest Victaulic Gasket Selection Guide for specific gasket service guidelines and for a listing of services which are not compatible.

18.12 6390 Rev L Updated 01/2016 © 2016 Victaulic Company. All rights reserved.

victaulic.com 2
victaulic.com

3.0  SPECIFICATIONS - MATERIAL (Continued)

Vic-Press Joining System for Schedule 10S Stainless Steel Pipe

PIPE STOP HOUSING

An internal pipe stop locates pipe position to ensure Precision formed stainless steel construction
positive joining. incorporating the pipe stop and seal.

PRESSED JOINT SEAL POCKET

Seal is compressed to provide a leak-free connection PRE-LUBRICATED SEAL
for a variety of wet and dry services. With patent-pending press detection technology.

INSERTION MARK POSITIVE MECHANICAL INTERLOCK

A witness mark made by The Vic-Press PFT510 hand-held tool engages
installer prior to installation the entire circumference of the fitting to ensure
allows for visual verification that a secure attachment of pipe to fitting.
the pipe has been fully inserted
for proper installation.

Dimensional Information
Products in the Vic-Press for Schedule 10S system for Type 304/304L stainless steel have unique center-to-end or
end-to-end dimensions which incorporate specific, “takeout” dimensions for easy fabrication calculations.
Use of threaded products employing special features such as probes, escutcheon cups, etc., should be checked to
be certain the thread standard and length of insertion are compatible with fitting dimensions.
Failure to verify dimensional suitability in advance may result in difficulties in assembly.

P End Type Code

P = Press
F = Female Thread
M = Male Thread
T = Plain End
P P L = Flanged
G = Grooved
EOB = End of Branch
W = Weld Ends

18.12 6390 Rev L Updated 01/2016 © 2016 Victaulic Company. All rights reserved.

victaulic.com 3
victaulic.com

4.0 DIMENSIONS
Standard Coupling
Style P597 (P x P)
Working Pressure: 500 psi/3450 kPa

E to E
U

Style P597

Size Dimensions Weight

Actual
Outside U Approximate
Nominal Diameter E to E Takeout (Each)
inches inches inches inches lb
DN mm mm mm kg
1/2 0.840 2.78 0.65 0.2
DN15 21.3 70.6 16.5 0.1
3/4 1.050 2.78 0.65 0.3
DN20 26.7 70.6 16.5 0.1
1 1.315 3.11 0.73 0.5
DN25 33.4 79.0 18.5 0.2
1 1/2 1.900 3.48 0.72 0.7
DN40 48.3 88.4 18.3 0.3
2 2.375 3.96 0.71 1.0
DN50 60.3 100.6 18.0 0.5

Tee
Style P593 (P x P x P)
Working Pressure: 500 psi/3450 kPa

C
to
EOB U
2

U1
C to P

Style P592

Size Dimensions Weight

Actual
Outside U1 U2 Approximate
Nominal Diameter C to P Takeout C to EOB Takeout (Each)
inches inches inches inches inches inches lb
DN mm mm mm mm mm kg
1/2 0.840 1.71 1.29 1.91 0.84 0.4
DN15 21.3 43.4 32.8 48.5 21.3 0.2
3/4 1.050 2.01 1.89 1.93 0.87 0.5
DN20 26.7 51.1 48.0 49.0 22.1 0.2
1 1.315 2.27 2.17 2.24 1.05 0.9
DN25 33.4 57.7 55.1 56.9 26.7 0.4
1 1/2 1.900 2.72 2.68 2.74 1.37 1.5
DN40 48.3 69.1 68.1 69.6 34.8 0.7
2 2.375 3.21 3.17 3.36 1.73 2.1
DN50 60.3 81.5 80.5 85.3 43.9 1.0

18.12 6390 Rev L Updated 01/2016 © 2016 Victaulic Company. All rights reserved.

victaulic.com 4
victaulic.com

4.1 DIMENSIONS
Tee with Reducing Branch
Style P593 (P x P x P)
Working Pressure: 500 psi/3450 kPa

C
to
EOB U2

U1
C to PE

Style P593

Dimensions Weight
Actual
Nominal Outside U1 U2 Approximate
Size Diameter C to P Takeout C to EOB Takeout (Each)
inches inches inches inches inches inches lb
DN mm mm mm mm mm kg
3/4 3/4 1/2 1.050 1.050 0.840 2.01 1.89 2.01 0.95 0.5
x x x x
DN20 DN20 DN15 26.7 26.7 21.3 51.1 48.0 51.1 24.1 0.2
1 1 1/2 1.315 1.315 0.840 2.27 2.17 2.14 1.08 0.8
x x x x
DN25 DN25 DN15 33.4 33.4 21.3 57.7 55.1 54.4 27.4 0.4
3/4 1.050 2.27 2.17 2.07 1.00 0.8
DN20 26.7 57.7 55.1 52.6 25.4 0.4
1 1/2 1 1/2 1/2 1.900 1.900 0.840 2.72 2.69 2.44 1.17 1.2
x x x x
DN40 DN40 DN15 48.3 48.3 21.3 69.1 68.3 62.0 29.7 0.5
3/4 1.050 2.72 2.69 2.36 1.29 1.3
DN20 26.7 69.1 68.3 59.9 32.8 0.6
1 1.315 2.72 2.69 2.53 1.34 1.4
DN25 33.4 69.1 68.3 64.3 34.0 0.6
2 2 1/2 2.375 2.375 0.840 3.21 3.16 2.67 1.61 1.7
x x x x
DN50 DN50 DN15 60.3 60.3 21.3 81.5 80.3 67.8 40.9 0.8
3/4 1.050 3.21 3.16 2.60 1.53 1.7
DN20 26.7 81.5 80.3 66.0 38.9 0.8
1 1.315 3.21 3.16 2.77 1.58 1.8
DN25 33.4 81.5 80.3 70.4 40.1 0.8
1 1/2 1.900 3.21 3.16 2.98 1.60 2.0
DN40 48.3 81.5 80.3 75.7 40.6 0.9

18.12 6390 Rev L Updated 01/2016 © 2016 Victaulic Company. All rights reserved.

victaulic.com 5
victaulic.com

4.2 DIMENSIONS
Tee with Threaded Branch
Style P588 (P x P x F2)
Working Pressure: 500 psi/3450 kPa

C
to
EOB U2

U1
C to PE

Style P588
*Length of effective thread

Dimensions Weight
Actual
Nominal Outside U1 U2 Approximate
Size Diameter C to P Takeout C to EOB Takeout (Each)
inches inches inches inches inches inches lb
DN mm mm mm mm mm kg
1/2 1/2 1/2 0.840 0.840 0.840 1.71 1.29 1.46 0.93 0.4
x x x x
DN15 DN15 DN15 21.3 21.3 21.3 43.4 32.8 37.1 23.6 0.2
3/4 3/4 1/2 1.050 1.050 0.840 2.01 1.89 1.57 1.04 0.5
x x x
DN20 DN20 DN15 26.7 26.7 21.3 51.1 48.0 39.9 26.4 0.2
3/4 1.050 2.01 1.89 1.56 1.02 0.6
DN20 26.7 51.1 48.0 39.6 25.9 0.3
1 1 1/2 1.315 1.315 0.840 2.27 2.17 1.70 1.17 0.9
x x x x
DN25 DN25 DN15 33.4 33.4 21.3 57.7 55.1 43.2 29.7 0.4
3/4 1.050 2.27 2.17 1.70 1.15 0.9
DN20 26.7 57.7 55.1 43.2 29.2 0.4
1 1.315 2.27 2.17 1.83 1.15 1.1
DN25 33.4 57.7 55.1 46.5 29.2 0.5
1 1/2 1 1/2 1/2 1.900 1.900 0.840 2.72 2.68 1.99 1.46 1.4
x x x x
DN40 DN40 DN15 48.3 48.3 21.3 69.1 68.1 50.5 37.1 0.6
3/4 1.050 2.72 2.68 1.99 1.44 1.5
DN20 26.7 69.1 68.1 50.5 36.6 0.7
1 1.315 2.72 2.68 2.12 1.44 1.5
DN25 33.4 69.1 68.1 53.8 36.6 0.7
2 2 1/2 2.375 2.375 0.840 3.21 3.17 2.23 1.70 1.7
x x x
DN50 DN50 DN15 60.3 60.3 21.3 85.1 80.5 56.6 43.2 0.8
3/4 1.050 3.21 3.17 2.23 1.68 1.7
DN20 26.7 85.1 80.5 56.6 42.7 0.8
1 1.315 3.21 3.17 2.36 1.68 2.0
DN25 33.4 85.1 80.5 59.9 42.7 0.9
2  Available with British Standard Pipe Threads. Specify BSPT on order.

18.12 6390 Rev L Updated 01/2016 © 2016 Victaulic Company. All rights reserved.

victaulic.com 6
victaulic.com

4.3 DIMENSIONS
Elbows
Style P586 90º Elbow (P × P)
Style P542 90º Street Elbow (P x T)
Style P591 45º Elbow (P x P)
Style P543 45º Street Elbow (P x T)
Working Pressure: 500 psi/3450 kPa
C to P C to T
U

C U
to
P

Style P586 Style P542

Style P586 Style P542

90° Elbow 90° Street Elbow
Actual
Nominal Outside U Approx. U Approx.
Size Diameter C to P Takeout Weight (Each) C to P Takeout C to T Weight (Each)
inches inches inches inches lb inches inches inches lb
DN mm mm mm kg mm mm mm kg
 1/2 0.840 2.64 1.53 0.3 2.64 1.53 3.04 0.3
DN15 21.3 67.1 38.9 0.1 67.1 38.9 77.2 0.1
 3/4 1.050 2.95 1.89 0.4 2.95 1.89 3.35 0.4
DN20 26.7 74.9 48.0 0.2 74.9 48.0 85.1 0.2
1 1.315 3.52 2.33 0.8 3.52 2.33 4.32 0.7
DN25 33.4 89.4 59.2 0.4 89.4 59.2 109.7 0.3
1 1/2 1.900 4.55 3.18 1.4 4.55 3.18 4.55 1.4
DN40 48.3 115.6 80.8 0.6 115.6 80.8 115.6 0.6
2 2.375 5.52 3.90 2.0 5.52 3.90 5.52 2.0
DN50 60.3 140.2 99.1 0.9 140.2 99.1 140.2 0.9

T
to
C

C U C U
to to
P P

Style P591 Style P543

Style P591 Style P543

45° Elbow 45° Street Elbow
Actual
Nominal Outside U Approx. U Approx.
Size Diameter C to P Takeout Weight (Each) C to P Takeout C to T Weight (Each)
inches inches inches inches lb inches inches inches lb
DN mm mm mm kg mm mm mm kg
 1/2 0.840 1.89 0.83 0.2 1.89 0.83 1.89 0.2
DN15 21.3 48.0 21.1 0.1 48.0 21.1 48.0 0.1
 3/4 1.050 2.56 1.50 0.4 2.56 1.50 2.56 0.4
DN20 26.7 65.0 38.1 0.2 65.0 38.1 65.0 0.2
1 1.315 3.27 2.09 0.8 3.27 2.09 3.27 0.8
DN25 33.4 83.1 53.1 0.4 83.1 63.9 83.1 0.4
1 1/2 1.900 4.96 3.59 1.7 4.96 3.59 4.96 1.7
DN40 48.3 126.0 91.2 0.8 126.0 91.2 126.0 0.8
2 2.375 5.84 4.22 2.5 5.84 4.22 5.84 2.5
DN50 60.3 148.3 107.2 1.1 148.3 107.2 148.3 1.1

18.12 6390 Rev L Updated 01/2016 © 2016 Victaulic Company. All rights reserved.

victaulic.com 7
victaulic.com

4.4 DIMENSIONS
Male Threaded Adapter Female Threaded Adapter
Style P596 (P x M3) Style P599 (P x F4)
Working Pressure: 500 psi/3450 kPa Working Pressure: 500 psi/3450 kPa
E to E E to E
IL U * IL U *

*Length of effective thread Style P596 *Length of effective thread Style P599

Dimensions Weight Dimensions Weight

Actual IL Actual IL
Nominal Outside E to E U Insertion Approx. Nominal Outside E to E U Insertion Approx.
Size Diameter Takeout Length (Each) Size Diameter Takeout Length (Each)
inches inches inches inches inches lb inches inches inches inches inches lb
DN mm mm mm mm kg DN mm mm mm mm kg
1/2 1/2 0.840 0.840 3.93 2.32 1.06 0.3 1/2 1/2 0.840 0.840 2.39 0.79 1.06 0.3
x x x x
DN15 DN15 21.3 21.3 99.8 58.9 26.9 0.1 DN15 DN15 21.3 21.3 60.7 20.1 26.9 0.1
3/4 1/2 1.050 0.840 3.34 1.75 1.06 0.4 3/4 1/2 1.050 0.840 2.31 0.71 1.06 0.3
x x x x
DN20 DN15 26.7 21.3 84.8 44.5 26.9 0.2 DN20 DN15 26.7 21.3 58.7 18.0 26.9 0.1
3/4 1.050 3.85 2.22 1.06 0.4 3/4 1.050 2.31 0.79 1.06 0.4
DN20 26.7 97.8 56.4 26.9 0.2 DN20 26.7 58.7 20.1 26.9 0.2
1 1.315 3.34 1.60 1.06 0.5 1 1/2 1.315 0.840 2.47 0.75 1.19 0.7
DN25 33.4 84.8 40.6 26.9 0.2 x x
DN25 DN15 33.4 21.3 62.7 19.1 30.2 0.3
1 3/4 1.315 1.050 3.50 1.77 1.19 0.5 3/4 1.050 2.47 0.73 1.19 0.6
x x
DN25 DN20 33.4 26.7 88.9 45.0 30.2 0.2 DN20 26.7 62.7 18.5 30.2 0.3
1 1.315 4.19 2.32 1.19 0.6 1 1.315 2.60 0.88 1.19 0.6
DN25 33.4 106.4 58.9 30.2 0.3 DN25 33.4 66.0 22.4 30.2 0.3
1 1/2 3/4 1.900 1.050 3.65 1.73 1.38 0.8 1 1/2 1 1.900 1.315 2.92 0.91 1.38 1.0
x x x x
DN40 DN20 48.3 26.7 92.7 43.9 35.1 0.4 DN40 DN25 48.3 33.4 74.2 23.1 35.1 0.5
1 1/2 1.900 4.38 2.28 1.38 1.0 1 1/4 1.660 2.92 0.86 1.38 0.8
DN40 48.3 111.3 57.9 35.1 0.5 DN32 42.4 74.2 21.8 35.1 0.4
2 2 2.375 2.375 4.86 2.46 1.63 1.4 1 1/2 1.900 2.92 0.86 1.38 1.0
x x
DN50 DN50 60.3 60.3 123.4 62.5 41.4 0.6 DN40 48.3 74.2 21.8 35.1 0.5
3  Available with British Standard Pipe Threads. Specify BSPT on order. 2 1 1/4 2.375 1.660 3.57 1.24 1.63 1.1
x x
DN50 DN32 60.3 42.4 90.7 31.5 41.4 0.5
End Cap 1 1/2 1.900 3.57 1.24 1.63 1.3
x
DN40 48.3 90.7 31.5 41.4 0.6
Style P540
2 2.375 3.57 1.24 1.63 1.2
Working Pressure: 500 psi/3450 kPa x
DN50 60.3 90.7 31.5 41.4 0.5
4  Available with British Standard Pipe Threads. Specify BSPT on order.
E to E
IL CL

Insertion Cut-off Line for

Mark future system expansion

Style P540

Dimensions Weight
Actual IL
Nominal Outside Insertion Approx.
Size Diameter E to E Length CL (Each)
inches inches inches inches Cut-off lb
DN mm mm mm Line kg
 1/2 0.840 4.00 1.06 0.5 0.24
DN15 21.3 101.60 26.9 12.7 0.11
 3/4 1.050 4.00 1.06 0.5 0.30
DN20 26.7 101.60 26.9 12.7 0.14
1 1.315 4.38 1.19 0.5 0.54
DN25 33.4 111.25 30.2 12.7 0.24
1 1/2 1.900 4.75 1.38 0.5 0.87
DN40 48.3 120.65 35.1 12.7 0.39
2 2.375 5.25 1.63 0.5 1.22
DN50 60.3 133.35 41.4 12.7 0.55

18.12 6390 Rev L Updated 01/2016 © 2016 Victaulic Company. All rights reserved.

victaulic.com 8
victaulic.com

4.5 DIMENSIONS
Threaded Union Concentric Reducer
Style P584 (P x P) Style P594 (P x P)
Working Pressure: 500 psi/3450 kPa Working Pressure: 500 psi/3450 kPa
E to E E to E
U U

Style P584 Style P594

Dimensions Weight Dimensions Weight

Actual Actual
Nominal Outside U Approx. Nominal Outside U Approx.
Size Diameter E to E Takeout (Each) Size Diameter E to E Takeout (Each)
inches inches inches inches lb inches inches inches inches lb
DN mm mm mm kg DN mm mm mm kg
 1/2 0.840 7.50 5.37 3.0 3/4 1/2 1.050 0.840 4.25 2.13 0.5
DN15 21.3 190.5 136.4 1.4 x x
DN20 DN15 26.7 21.3 108.0 54.1 0.2
 3/4 1.050 7.37 5.24 3.7 1 1/2 1.315 0.840 4.92 2.67 0.6
DN20 26.7 187.2 133.1 1.7 x x
DN25 DN15 33.4 21.3 125.0 67.8 0.3
1 1.315 7.59 5.21 4.3 3/4 1.050 4.84 2.59 0.7
DN25 33.4 192.8 132.3 2.0 DN20 26.7 122.9 65.8 0.3
1 1/2 1.900 8.36 5.61 6.0 1 1/2 1/2 1.900 0.840 5.57 3.13 0.9
DN40 48.3 212.3 142.5 2.7 x x
DN40 DN15 48.3 21.3 141.5 79.5 0.4
2 2.375 8.01 4.76 6.8 3/4 1.050 5.49 3.06 1.0
DN50 60.3 203.5 120.9 3.1 DN20 26.7 139.4 77.7 0.5
1 1.315 5.66 3.09 1.1
Transition Nipple DN25 33.4 143.8 78.5 0.5
2 1/2 2.375 0.840 6.52 3.84 1.2
Style P587 (G × T) x x
DN50 DN15 60.3 21.3 165.6 97.5 0.5
Working Pressure: 500 psi/3450 kPa 3/4 1.050 6.44 3.76 1.3
DN20 26.7 163.6 95.5 0.6
E to E
L1 1 1.315 6.60 3.79 1.4
DN25 33.4 167.6 96.3 0.6
1 1/2 1.900 6.75 3.76 1.6
DN40 48.3 171.5 95.5 0.7
Insertion
Mark

Style P587

Dimensions Weight
Actual
Nominal Outside L1 Approx.
Size Diameter E to E Minimum (Each)
inches inches inches inches lb
DN mm mm mm kg
 3/4 1.050 4.00 1.06 0.3
DN20 26.7 101.6 26.9 0.1
1 1.315 4.00 1.19 0.5
DN25 33.4 101.6 30.2 0.2
1 1/2 1.900 4.00 1.38 0.7
DN40 48.3 101.6 35.1 0.3
2 2.375 4.00 1.63 0.9
DN50 60.3 101.6 41.4 0.4

18.12 6390 Rev L Updated 01/2016 © 2016 Victaulic Company. All rights reserved.

victaulic.com 9
victaulic.com

4.6 DIMENSIONS
Flange Adapter Van Stone Flange Adapter
Raised face one-piece 304L stainless steel flange adapter Carbon Steel raised face slip on flange, with 304 stainless
steel stub end
Style P595 (P x L)
Working Pressure: 275 psi/1896 kPa Style P565 (P x L)
Working Pressure: 275 psi/1896 kPa
E to E
U E to E
U

W X Y W X Y

Style P595 Style P565

ANSI Class 150 Flange Adapter Dimensions Weight

Dimensions Weight Actual
Nominal Outside U Approx.
Actual
Size Diameter E to E W X Y Takeout (Each)
Nominal Outside U Approx.
Size Diameter E to E W X Y Takeout (Each) inches inches inches inches inches inches inches lb
DN mm mm mm mm mm mm kg
inches inches inches inches inches inches inches lb
DN mm mm mm mm mm mm kg  1/2 0.840 3.37 1.38 2.38 3.50 2.30 2.4
 1/2 0.840 3.46 1.38 2.38 3.50 2.39 2.2 DN15 21.3 85.6 35.0 60.5 88.9 58.4 1.1
DN15 21.3 87.9 35.0 60.5 88.9 60.7 1.0  3/4 1.050 3.29 1.69 2.75 3.88 2.22 2.5
DN20 26.7 83.6 42.9 69.9 98.6 56.4 1.1
 3/4 1.050 3.34 1.69 2.75 3.88 2.27 2.3
DN20 26.7 84.8 42.9 69.9 98.6 57.7 1.0 1 1.315 3.45 2.00 3.12 4.25 2.26 3.0
1 1.315 3.46 2.00 3.12 4.25 2.27 2.8 DN25 33.4 87.6 50.8 79.3 108.0 57.4 1.4
DN25 33.4 87.9 50.8 79.3 108.0 57.7 1.3 1 1/2 1.900 3.61 2.88 3.88 5.00 2.22 4.1
1 1/2 1.900 3.45 2.88 3.88 5.00 2.07 3.6 DN40 48.3 91.7 73.2 98.6 127.0 56.4 1.9
DN40 48.3 87.6 73.2 98.6 127.0 52.3 1.6 2 2.375 4.55 3.62 4.75 6.00 2.92 6.8
2 2.375 3.42 3.62 4.75 6.00 1.79 5.8 DN50 60.3 115.6 92.0 120.7 152.4 74.2 3.1
DN50 60.3 86.9 92.0 120.7 152.4 45.5 2.6

Weld Adapter
Style P561 (P × W)
Working Pressure: 500 psi/3450 kPa
E to E
IL U

Style P561

Dimensions Weight
Actual IL
Nominal Outside U Insert. Approx.
Size Diameter E to E Takeout Length (Each)
inches inches inches inches inches lb
DN mm mm mm mm kg
 1/2 0.840 3.92 2.85 1.06 0.3
DN15 21.3 99.6 72.4 26.9 0.1
 3/4 1.050 3.84 2.77 1.06 0.4
DN20 26.7 97.5 70.4 26.9 0.2
1 1.315 4.18 3.00 1.19 0.6
DN25 33.4 106.2 76.2 30.2 0.3
1 1/2 1.900 4.37 2.98 1.38 0.9
DN40 48.3 111.0 75.7 35.1 0.4
2 2.375 4.85 3.22 1.63 1.4
DN50 60.3 123.2 81.8 41.4 0.6

18.12 6390 Rev L Updated 01/2016 © 2016 Victaulic Company. All rights reserved.

victaulic.com 10
victaulic.com

4.7 DIMENSIONS
Vic-Press Schedule 10S Type 316 Stainless Steel Ball Valve
Style P569
Working Pressure: 400 psi/2750 kPa
Series P569 Vic-Press for Schedule 10S System Ball Valves with Type 316 ends feature full stainless steel body and
trim, rated for service up to 400 psi/2750 kPa.
The valves are constructed of rugged Type 316 (CF8M) stainless steel with PTFE seats. The valves feature a blow-out
proof stem and self-adjusting floating ball which provides uniform sealing. The full port design minimizes pressure
drop for maximum flow efficiency. The three-piece swing-out design permits easy in-line maintenance.
Vic-Press for Schedule 10S x Vic-Press Schedule 10S (P x P)
E

C
A

Dimensions Weight
Actual
Nominal Outside A Approximate
Size Diameter End to End B C E (Each)
inches inches inches inches inches inches lb
DN mm mm mm mm mm kg
 1/2 0.840 8.26 2.17 1.06 5.24 1.5
DN15 21.3 209.8 55.1 26.9 133.1 0.7
 3/4 1.050 8.36 2.32 1.06 5.24 2.4
DN20 26.7 212.3 58.9 26.9 133.1 1.1
1 1.315 8.77 2.76 1.19 6.02 3.6
DN25 33.4 222.8 70.1 30.2 152.9 1.6
1 1/2 1.900 9.76 3.31 1.38 7.52 6.9
DN40 48.3 247.9 84.1 35.1 191.0 3.1
2 2.375 9.83 3.62 1.63 7.52 9.5
DN50 60.3 249.7 91.9 41.4 191.0 4.3

Groove x Groove (G x G)
E

Dimensions Weight

Nominal Actual A Approximate

Size Outside Diameter End to End B E (Each)
inches inches inches inches inches lb
DN mm mm mm mm kg
 3/4 1.050 8.54 2.32 5.24 2.4
DN20 26.7 216.9 58.9 133.1 1.1
1 1.315 8.75 2.76 6.02 3.6
DN25 33.4 222.3 70.1 152.9 1.6
1 1/2 1.900 10.90 3.31 7.52 6.9
DN40 48.3 276.9 84.1 191.0 3.1
2 2.375 12.11 3.62 7.52 9.5
DN50 60.3 307.6 91.9 191.0 4.3
NOTE
• For dimensions and weights with gear operator contact Victaulic.

18.12 6390 Rev L Updated 01/2016 © 2016 Victaulic Company. All rights reserved.

victaulic.com 11
victaulic.com

4.8 DIMENSIONS
Vic-Press Schedule 10S x Groove (P x G)
E

C
A

Dimensions Weight
Actual
Nominal Outside A Approximate
Size Diameter End to End B C E (Each)
inches inches inches inches Lbs. inches lb
DN mm mm mm kg mm kg
 3/4 1.050 8.44 2.32 1.06 5.24 2.4
DN20 26.7 214.4 58.9 26.9 133.1 1.1
1 1.315 8.76 2.76 1.19 6.02 3.6
DN25 33.4 222.5 70.1 30.2 152.9 1.6
1 1/2 1.900 10.32 3.31 1.38 7.52 6.9
DN40 48.3 262.1 84.1 35.1 191.0 3.1
2 2.375 10.92 3.62 1.63 7.52 9.5
DN50 60.3 277.4 91.9 41.4 191.0 4.3
2 2.375 9.83 3.62 1.63 7.52 9.5
DN50 60.3 249.7 91.9 41.4 191.0 4.3
NOTE
• For dimensions and weights with gear operator contact Victaulic.

Series P569 Material Specifications

Body: Made from Type 304L stainless steel.
Ball: Stainless steel, CF8M, ASTM A-351
Stem: Stainless steel, Type 316
Seats: (PTFE) Polytetrafluoroethylene
Locking Handle: Stainless steel, Type 304
Stem Nut: Reducer body made from Type 304 stainless steel, press ends made from Type 304L stainless steel.
Stem Washer: Stainless steel, Type 304
Stem Packing and Thrust Washer: (PTFE) Polytetrafluoroethylene
Bolt/Nut/Washer: Stainless steel, Type 304
Cap: Stainless steel, CF8M, ASTM A-351
Extended Ends: Schedule 10S Stainless steel, Type 316
Specify end style:
Vic-Press Schedule 10S x Vic-Press Schedule 10S (P x P)
Grooved End (G x G)
Vic-Press Schedule 10S x Grooved End (P x G)

18.12 6390 Rev L Updated 01/2016 © 2016 Victaulic Company. All rights reserved.

victaulic.com 12
victaulic.com

5.0 PERFORMANCE
Flow Characteristics
Flow testing for the Vic-Press Style P569 3-Piece Ball Valve demonstrated superior flow characteristics.
Testing was performed in our own engineering laboratory facilities with systems and equipment calibrated to National
Bureau of Standards.
CV/KV values for flow of water at +60°F/+16°C with a fully open valve are shown in tables below.
Formulas for CV values
Flow Coefficient Cv Kv
ΔP = Q 2 /CV2 ΔP = Q 2 /K V2
Q (Flow) GPM m3/hr
Q = CV × √ΔP Q = K V × √ΔP
ΔP (Pressure Drop) psi bar

Valve Size Full Open

Nominal Actual
Size Outside Diameter Flow Coefficient
inches inches Cv
DN mm Kv
 1/2 0.840 10
DN15 21.3 9
3/4 1.050 17
DN20 26.7 14
1 1.315 45
DN25 33.4 39
1 1/2 1.900 125
DN40 48.3 107
2 2.375 365
DN50 60.3 314

Series P569 Repair Kits

Kits and replacement parts are available for the Series P569 valve.
The Repair Kit consists of two seats, two gaskets, one stem seal and one thrust washer, all made of PTFE.
A replacement ball of CF8M stainless steel is also available.
For replacement stem information, contact Victaulic.

Size Repair Kit Replacement Ball

Actual
Nominal Outside
Size Diameter
inches inches
DN mm Part No. Part No.
 1/2 0.840
K-004-569-001 K-004-569-000
DN15 21.3
3/4 1.050
K-006-569-001 K-006-569-000
DN20 26.7
1 1.315
K-010-569-001 K-010-569-000
DN25 33.4
1 1/2 1.900
K-014-569-001 K-014-569-000
DN40 48.3
2 2.375
K-020-569-001 K-020-569-000
DN50 60.3

18.12 6390 Rev L Updated 01/2016 © 2016 Victaulic Company. All rights reserved.

victaulic.com 13
victaulic.com

5.1 PERFORMANCE
Vic-Press Brass Body Ball Valve with Stainless Steel Vic-Press Schedule 10S Ends
Style P589* (P x P)
Working Pressure: 300 psi/2065 kPa
Series P589 Ball Valve is a full port valve with Vic-Press Schedule 10S ends for fast, easy installation. The valve, with
Vic-Press Schedule 10S ends, is designed for service to 300 psi/ 2068 kPa.
The valve body is constructed from forged brass. The ball is chrome plated brass and seals on PTFE seats. A hollow
ball design eliminates unnecessary weight while maintaining flow and mechanical strength. PTFE seats and washers
reduce the friction coefficient which eases valve operation.
The Vic-Press Schedule 10S ends are of ASTM A-312 Type 304 stainless steel.
The Series P589 Brass Body Ball Valve is NOT ANSI/NSF certified for potable water. For potable water applications
use the Series P569 Stainless Steel Ball Valve.
C

D
A

Dimensions Weight
A Flow
Nominal Actual ± 0.125 Approximate Coefficient5
Size Outside Diameter 3.18 B C D (Each) (Fully Open)
inches inches inches inches inches inches lb CV Values
DN mm mm mm mm mm kg KV Values
 1/2 0.840 9.030 1.42 3.03 1.06 1.0 11
DN15 21.3 229.3 36.1 77.0 26.9 0.5 9.4
 3/4 1.050 9.120 1.90 3.74 1.06 1.6 25
DN20 26.7 231.7 48.3 95.0 26.9 0.7 21.3
1 1.315 10.11 2.05 3.74 1.19 2.8 36
DN25 33.4 256.7 52.1 95.0 30.2 1.3 30.7
1 1/2 1.900 11.18 2.76 5.40 1.38 4.7 112
DN40 48.3 283.9 70.1 137.2 35.1 2.1 95.5
2 2.375 12.69 3.15 5.40 1.63 6.9 195
DN50 60.3 322.3 80.0 137.2 41.4 3.1 166.3

Working Pressure: 300 psi/2065 kPa

Series P589 Material Specifications
Valve Body: Forged Brass ASTM B-30
Ball: Brass ASTM B-30, chrome plated
Stem: Brass ASTM B-16
Seats: (PTFE) Polytetrafluoroethylene
Handle: Carbon steel, zinc plated
Stem Nut: Carbon steel, zinc plated
Stem Washer: (PTFE) Polytetrafluoroethylene
Extended Ends: Schedule 10S Stainless Steel, Type 304

18.12 6390 Rev L Updated 01/2016 © 2016 Victaulic Company. All rights reserved.

victaulic.com 14
victaulic.com

5.2 PERFORMANCE
Pipe Support
Piping joined with Vic-Press Schedule 10S System products for Type 304 stainless steel, like all other piping systems,
requires support to carry the weight of pipes and equipment. As for other methods of joining pipes, the support or
hanging method must be such as to eliminate undue stresses on joints, piping and other components. Additionally,
the method of support must be such as to allow movement of the pipes where required and to provide drainage, etc.,
as may be specified by the designer.
The maximum hanger spacing corresponds to ASME B31.1, B31.3 or B31.9 as noted, and should be used in
conjunction with Victaulic Vic-Press Schedule 10S System products on approved Type 304 Schedule 10S stainless
steel pipe.

Suggested Max. Span

Actual
Between Supports - Feet/meters
Nominal Outside
Size Diameter Water Service Gas/Air Service
inches inches
DN mm B31.1 B31.3 B31.9 B31.1 B31.3 B31.9
 1/2 0.840 6.5 6.5 7.0 7.0 7.0 7.5
DN15 21.3 2.0 2.0 2.1 2.1 2.1 2.3
 3/4 1.050 7.5 7.5 8.5 8.0 8.0 9.0
DN20 26.7 2.3 2.3 2.6 2.4 2.4 2.7
1 1.315 8.5 8.5 10.0 9.0 9.0 10.5
DN25 33.4 2.6 2.6 3.1 2.7 2.7 3.2
1 1/2 1.900 10.0 10.0 12.5 11.0 11.0 13.5
DN40 48.3 3.1 3.1 3.8 3.6 3.6 4.1
2 2.375 11.0 11.0 13.0 12.5 12.5 15.5
DN50 60.3 3.6 3.6 4.0 3.8 3.8 4.7

5.3 PERFORMANCE
Thermal Expansion/Contraction
For stainless steel pipes, expansion/contraction will occur with temperature changes at a rate of 1 1/8 inch per 100
feet of pipe per 100°F (96mm per 100 meters of pipe per 100°C). This change in length may not seem significant;
however, piping which cannot expand or contract may create substantial stresses within the piping system resulting in
damage to the piping system and/or components.
The change in length due to thermal movement may be absorbed by the flexibility of the piping system, particularly
in systems using light wall pipe. This can be done at a simple change in direction using an “L-Bend”, or with an
offset leg in a “Z-Bend” configuration or with a “U-Bend” (expansion loop). A proper design will utilize offset legs
of sufficient minimum length prior to any element that will restrict movement (anchors, guides, fixed equipment
connection) to minimize pipe stress. In addition, since these methods are symmetric about the offset axis, (i.e.:
The expansion loop can open or close in equal amounts), one only needs to size the compensator for the greater of
the thermal expansion or contraction from the installed ambient condition. The following charts that designate the
minimum offset leg length for each of the aforementioned configurations were developed from the methodology found
in ASHRAE Handbook – Systems and Equipment.

18.12 6390 Rev L Updated 01/2016 © 2016 Victaulic Company. All rights reserved.

victaulic.com 15
victaulic.com

5.3  PERFORMANCE (Continued)

Thermal Expansion/Contraction

∆L

Offset Leg
Length

"L-Bend" Expansion Compensator

“L - Bend” Expansion Compensator “L - Bend” Expansion Compensator

180.0 450.0

160.0 400.0
2"
140.0 350.0 50mm
1½"
Leg Length in Centimeters

40mm
Leg Length in Inches

120.0 300.0
1"
100.0 ¾" 250.0 25mm
½" 20mm
80.0 200.0 15mm

60.0 150.0

40.0 100.0

20.0 50.0

0.0 0.0
0.25 0.5 0.75 1 1.25 1.5 1.75 2 10 20 30 40 50
Displacement ( ∆ L) in Inches Displacement (∆ L) in Millimeters

18.12 6390 Rev L Updated 01/2016 © 2016 Victaulic Company. All rights reserved.

victaulic.com 16
victaulic.com

5.3  PERFORMANCE (Continued)

Thermal Expansion/Contraction

Offset Leg
Length

ΔL

"Z-Bend" Expansion Compensator

“Z - Bend” Expansion Compensator

“Z - Bend” Expansion Compensator
120.0 300.0

100.0 250.0
2"
1½" 50mm
Leg Length in Centimeters
Leg Length in Inches

80.0
200.0 40mm
1"
¾" 25mm
60.0
½" 150.0 20mm
15mm
40.0
100.0

20.0
50.0

0.0
0.25 0.5 0.75 1 1.25 1.5 1.75 2 0.0
Displacement ( ∆ L) in Inches 10 20 30 40 50
Displacement (∆ L) in Millimeters

18.12 6390 Rev L Updated 01/2016 © 2016 Victaulic Company. All rights reserved.

victaulic.com 17
victaulic.com

5.3  PERFORMANCE (Continued)

Thermal Expansion/Contraction

ΔL ΔL
2 2

Offset Leg Length

=
2

Offset Leg
Length

"U-Bend" Expansion Compensator

“Expansion Loop” Compensator “Expansion Loop” Compensator

70.0 180.0

60.0 160.0
2"

140.0
Leg Length in Centimeters

1½" 50mm
50.0
40mm
Leg Length in Inches

1"
120.0
40.0 ¾" 25mm
100.0
½" 20mm
30.0 80.0 15mm

60.0
20.0
40.0
10.0
20.0
0.0 0.0
0.25 0.5 0.75 1 1.25 1.5 1.75 2 10 20 30 40 50
Displacement (∆ L) in Inches Displacement (∆ L) in Millimeters

18.12 6390 Rev L Updated 01/2016 © 2016 Victaulic Company. All rights reserved.

victaulic.com 18
victaulic.com

5.0  PERFORMANCE (Continued)

Thermal Expansion/Contraction
Examples

L-Bend
A 1"/25mm diameter pipeline will have thermal growth
of 1.50"/40mm (ΔL) towards the elbow as shown in the
"L - Bend" Expansion Compensator
above Figure 1. What is the minimum offset leg length 180.0
from the elbow to the pipe restriction for the “L-Bend”

Leg Length in Inches

160.0
2"
configuration? 140.0 1½"
120.0
Use the “L-Bend” expansion compensator graph. Find 100.0
1"
¾"
the intersection of ΔL=1.50"/40mm (on the horizontal 80.0
½"

axis) where it crosses the 1"/25mm pipe curve. At that 60.0

point, read the “Leg Length in Inches” (on the vertical 40.0
20.0
axis) to determine the minimum offset leg length from 0.0
the elbow to the pipe restriction. For a thermal growth of 0.25 0.5 0.75 1 1.25 1.5 1.75 2
1.50"/40mm of 1"/25mm diameter pipe in an “L-Bend”
Displacement (∆L) in Inches
configuration, the minimum offset leg length should be
105"/2670mm.

Z-Bend
A 1.50"/40mm diameter pipeline will have thermal
growth of 1.25"/30mm between two opposing anchors,
however,there is a perpendicular offset designed within "Z - Bend" Expansion Compensator
300.0
the piping system that may be used to accommodate
the thermal growth of the main run of pipe. What is the 250.0
Leg Length in

50mm
Centimeters

minimum offset leg length required for this “Z-Bend” 200.0 40mm

configuration to accommodate the 1.25"/30mm of thermal 150.0

25mm
20mm
15mm
growth?
100.0
Use the “Z-Bend” expansion compensator graph. Find
50.0
the intersection of ΔL=1.25"/30mm (on the horizontal axis)
where it crosses the 1.50"/40mm pipe curve. At that point, 0.0
read the “Leg Length in Centimeter” (on the vertical axis) 10 20 30 40 50
to determine the minimum offset leg length. For a thermal Displacement (∆L) in Millimeters
growth of 1.25"/30mm of 1.50"/40mm diameter pipe in
a “Z-Bend” configuration, the minimum offset leg length
should be 7.25"/186cm.

Expansion Loop
A 2"/50mm diameter pipeline will have thermal growth
of 1.75"/45mm between two opposing anchors. The "Expansion Loop" Compensator
configuration of the system is such that there are no 70.0
Leg Length in Inches

changes in direction; straight pipe only between the 60.0 2"

anchors. To accommodate the thermal growth an 50.0 1½"

expansion loop will be required. What is the minimum 40.0

1"
¾"
offset leg length required for this expansion loop to 30.0
½"

accommodate the 1.75"/45mm of thermal growth? 20.0

Use the “Expansion Loop” compensator graph. Find the 10.0
intersection of ΔL=1.75"/45mm (on the horizontal axis) 0.0
where it crosses the 2"/50mm pipe curve. At that point, 0.25 0.5 0.75 1 1.25 1.5 1.75 2
read the "Leg Length in Inches" (on the vertical axis) to
Displacement (∆L) in Inches
determine the minimum offset leg length of the expansion
loop. For a thermal growth of 1.75"/45mm of 2"/50mm
diameter pipe in an “L-Bend” configuration, the minimum
offset leg length should be 61"/1550mm.

18.12 6390 Rev L Updated 01/2016 © 2016 Victaulic Company. All rights reserved.

victaulic.com 19
victaulic.com

5.4 PERFORMANCE
Vic-Press Tool
Vic-Press PFT510

PFT510

• The PFT-510 Vic-Press tool is specifically designed to join Vic-Press components to Schedule 10S* stainless steel
pipe. Can also be used for Schedule 5S pipe using Vic-Press components.
• Tool package includes one (1) Vic-Press PFT510 tool, two (2) 18V Lithium Ion batteries, one (1) battery charger,
one (1) tool carrying case, one (1) jaw carrying case, one (1) ½"/15mm jaw, one (1) ¾"/20mm jaw, one (1)
1"/25mm jaw, one (1) 1½"/40mm hinged jaw, one (1) 2"/50mm hinged jaw, and one (1) adapter jaw, one (1) set of
insertion gauges, one (1) cleaning brush, and one (1) marker.
• Jaws are included with every tool purchase.
• Vic-Press PFT510 is designed for industrial and trade use only
Capacity: ½"/15mm, ¾"/20mm, 1"/25mm, 1 ½"/40mm, 2"/50mm Schedule 10S stainless steel pipe
Power Charger Requirements: 110 volt/60 cycle/6.5 amp
Optional: 220 volt
NOTES
• The Vic-Press for Schedule 10S System is not compatible with PFT505 and/or PFT509 tools/ components. The Vic-Press Schedule 10S System requires the
use of a Vic-Press FT510 tool package.
• The Victaulic PFT510 tool is the only press tool approved for use on the Vic-Press® for Schedule 10S System.

18.12 6390 Rev L Updated 01/2016 © 2016 Victaulic Company. All rights reserved.

victaulic.com 20
victaulic.com

6.0 NOTIFICATIONS

WARNING
• Vic-Press for Schedule 10S products for Type 304 /304L stainless steel must only be used on services
compatible with seal and fitting materials.

Incompatible services may result in leakage. Always reference the latest Victaulic Gasket Selection Guide (05.01) for
specific seal service recommendations and for a listing of services which are not recommended.

WARNING
• It is the responsibility of designers of piping systems to verify the suitability of Schedule 10S, Type 304/304L
stainless steel pipe for use with the intended fluid media. The fluid’s chemical composition, pH level, operating
temperature, chloride level, oxygen level and flow rate and their effect on AISI Type 304/304L stainless steel
must be evaluated by the material specifier to confirm system life will be adequate for the intended service.

Failure to do so may cause serious personal injury or property damage.

7.0  REFERENCE MATERIALS

05.01: Gasket Selection Guide
02.06: Approvals for Potable Water Products
18.11: Vic-Press(TM) for Schedule 10S Type 316 Stainless Steel
18.13: Vic-Press(TM) for Schedule 10S Qualification Test Data
18.14: 3 Piece Stainless Steel Ball Valve
18.16: Vic-Press(TM) for Schedule 10S ASME B31.1 Compliance
18.17: Vic-Press(TM) for Schedule 10S ASME B31.3 Compliance
18.18: Vic-Press(TM) for Schedule 10S ASME B31.9 Compliance

User Responsibility for Product Selection and Suitability Note

Each user bears final responsibility for making a determination as to the suitability of This product shall be manufactured by Victaulic or to Victaulic specifications. All products
Victaulic products for a particular end-use application, in accordance with industry to be installed in accordance with current Victaulic installation/assembly instructions.
standards and project specifications, as well as Victaulic performance, maintenance, Victaulic reserves the right to change product specifications, designs and standard
safety, and warning instructions. Nothing in this or any other document, nor any verbal equipment without notice and without incurring obligations.
recommendation, advice, or opinion from any Victaulic employee, shall be deemed to Installation
alter, vary, supersede, or waive any provision of Victaulic Company's standard conditions Reference should always be made to the Victaulic installation handbook or installation
of sale, installation guide, or this disclaimer. instructions of the product you are installing. Handbooks are included with each shipment
Intellectual Property Rights of Victaulic products, providing complete installation and assembly data, and are available
No statement contained herein concerning a possible or suggested use of any material, in PDF format on our website at www.victaulic.com.
product, service, or design is intended, or should be constructed, to grant any license Warranty
under any patent or other intellectual property right of Victaulic or any of its subsidaries Refer to the Warranty section of the current Price List or contact Victaulic for details.
or affiliates covering such use or design, or as a recommendation for the use of such
material, product, service, or design in the infringement of any patent or other intellectual Trademarks
property right. The terms “Patented” or “Patent Pending” refer to design or utility patents Victaulic and all other Victaulic marks are the trademarks or registered trademarks of
or patent applications for articles and/or methods of use in the United States and/or other Victaulic Company, and/or its affiliated entities, in the U.S. and/or other countries.
countries.

18.12 6390 Rev L Updated 01/2016 © 2016 Victaulic Company. All rights reserved.

victaulic.com 21