Hand Pump
Hand Pump
HP121DA95
FEATURES:
HP121DAH50
ORING PORT to eliminate leakage. DELRIN SEAT to seal between tank inlet and piston reservoir. ORING OUTLET CHECK for zero leakage. ORING SEAL between tank and casting. STEEL BALL RELEASE VALVE allows oil to travel to tank and relieves pressure on the outlet line. EVERY HP IS TESTED for outlet check leakage, double or single pump action and relief setting. OPTIONAL HORIZONTAL MOUNTING BRACKETS allows for horizontal handle actuation.
Volume Displacement HP22SA 0.20 in3 (3.3 cm3) (When handle is MATERIALS: pulled). Cast Iron Body HP61DA 0.60 in3 (9.8 cm3) per full cycle. Buna N ORings HP121DA 1.20 in3 (19.7 cm3) per full cycle. Delrin Inlet Seat Tank sizes Stainless Steel Piston 95 in3 (1557 cm3), 80 in3 (1311 cm3), 65 in3 (1065 cm3), and 50 in3. (819 cm3). TL 2 in. (50.8 mm) tank used with remote reservoir. Pressure rating and (Standard relief setting). HP22SA 6000 psi, 414 bar (4000 psi, 276 bar). HP61DA 3000 psi (3000 psi, 207 bar). HP121DA 2000 psi (2000 psi, 138 bar). Outlet Port Size #6 SAE (9/16-18). Filler Port Size 1/4 NPT.
SPECIFICATIONS:
02-08
Page H-1
Hand Pumps
HP GENERAL INFORMATION
The Brand, hand operated hydraulic pump comes in three basic models HP121DA, HP61DA and HP22SA. Each one of these models comes with a relief that can be adjusted manually to suit the customers requirements. Brand has also redesigned the outlet check seat for zero leakage. The zero leak seat was created by utilizing an oring seal to replace the steel ball seal. The NT (no tank) option does not have a tank, pressure relief and release valve. To use the NT option the customer must connect the inlet of the hand pump to an external reservoir (external reservoir is not supplied by Brand). The TL (2 in. tank) option has a small tank, pressure relief and release valve. To use the TL option the customer must connect the fill port on the tank to an external reservoir (external reservoir is not supplied by Brand). When mounting the NT or TL option, the pump should be placed below the fluid level of the external reservoir. All standard tanks have a 1/4 NPT filler plug at the top of the tank. HP22SA has a single-acting piston that can pump 0.20 in3 (3.3 cm3) per full cycle. The term singleacting means that the piston only pumps fluid when the handle is pulled away from the pump. The piston does not displace fluid when the handle is pushed towards the pump. The pressure rating is higher then the HP121DA because it takes less force to displace the smaller surface area of the piston. This pump is typically used in applications that require low volume displacement and high pressure. HP61DA has a double-acting piston that can pump 0.60 in3 (9.8 cm3) per full cycle. The term doubleacting means that the piston pumps fluid when the handle is pushed and pulled. The pressure rating is higher then the HP121DA because it takes less force to displace the piston. This pump is typically used in applications that require medium volume displacement and medium pressure. HP121DA has a large double-acting piston that can pump 1.20 in3 (19.7 cm3) per full cycle. The term double-acting means that the piston pumps fluid when the handle is pushed and pulled. The pressure rating is lower then the HP22SA and HP61DA because it takes a greater amount of force to displace a piston that has a large surface area. This pump is typically used in applications that require high volume displacement and lower pressure.
HP22SA50... 0.20 in3 (3.3 cm3) displacement, single acting and 50 in3 (819 cm3) tank. HP61DA95... 0.60 in3 (9.8 cm3) displacement, double acting and 95 in3 (1557 cm3) tank. HP121DA65. 1.20 in3 (19.7 cm3) displacement, double acting and 65 in3 (1065 cm3) tank.
Hand Pumps
OUTLET
BRA
P.N. S.N.
YD
ICS
3/4" PIPE
4X
8 0 .2
7 " [
.1]
95 CU. IN.
65 CU. IN.
TANK
50 CU. IN.
BODY
1.5"[38.1]
2"[50.8]
4.00" [101.6]
4.00" [101.6]
#6 SAE OUTLET
Page H-3
Hand Pumps
4X
15.8" [401.3] (12" TANK) 13.8" [350.5] (10" TANK) 11.8" [299.7] (8" TANK) 9.8" [248.9] (6" TANK)
Page H-4
.9 9 "[ .39 0 2]
ADJUSTABLE RELIEF