AMS2252ΠREV.

E
AEROSPACE
MATERIAL SPECIFICATION Issued 1945-07
Reaffirmed 2006-03
Revised 2016-11

Superseding AMS2252D

(R) Tolerances
Low-Alloy Steel Sheet, Strip, and Plate

RATIONALE

AMS2252E is a Five-Year review and update of this specification that includes the addition of and alignment with relevant
ASTM tables.

1. SCOPE

This specification covers established inch/pound manufacturing tolerances applicable to low-alloy steel sheet, strip, and

--``,,,,`,``,,,,```,``,````,`,``-`-`,,`,,`,`,,`---
plate ordered to inch/pound dimensions. These tolerances apply to all conditions unless otherwise noted. 7KHWHUP³H[FO´
is used to apply only to the higher figure of the specified range.

1.1 MAM2252, the metric version of this AMS, has been cancelled and superseded by this specification.

2. REFERENCES

2.1 Applicable Documents

The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the
extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is
specified. When the referenced document has been cancelled and no superseding document has been specified, the last
published issue of that document shall apply.

2.1.1 ASTM Publications

Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel:
610-832-9585, www.astm.org.

ASTM A6 Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and
Sheet Piling

ASTM A505 Standard Specification for Steel, Sheet and Strip, Alloy, Hot-Rolled and Cold-Rolled, General Requirements
for

__________________________________________________________________________________________________________________________________________
6$(7HFKQLFDO6WDQGDUGV%RDUG5XOHVSURYLGHWKDW³7KLVUHSRUWLVSXEOLVKHGE\6$(WRDGYDQFHWKHVWDWHRIWHFKQLFDODQGHQJLneering sciences. The use of this report is entirely
voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility oIWKHXVHU´
SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and
suggestions.
Copyright © 2016 SAE International
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior written permission of SAE.
TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) SAE values your input. To provide feedback on this
Tel: +1 724-776-4970 (outside USA) Technical Report, please visit
Fax: 724-776-0790 http://standards.sae.org/AMS2252E
Copyright SAE International
Provided by IHS Markit under license with SAE Email: CustomerService@sae.org Licensee=Zodiac Seats LLC Engineering/5935306001, User=Hernandez, Juan
SAEorWEB
No reproduction ADDRESS:
networking permitted without license from IHS http://www.sae.org Not for Resale, 09/24/2018 13:19:22 MDT
 SAE INTERNATIONAL AMS2252ŒE Page 2 of 9
2.2 Definition of Terms

2.2.1 COMPARABLE: The table in this specification has similar attributes, but the values and/or limits are different from
the referenced table.

2.2.2 EQUIVALENT: The table in this specification has the same values and limits as the referenced table.

3. THICKNESS

3.1 Hot Rolled Sheets; Coils and Cut Lengths

See Table 1, (equivalent to ASTM A505-16 Table 4).

Table 1 - Thickness tolerance, inch, plus and minus; for inch width ranges shown

Over 24 Over 32 Over 40 Over 48 Over 60 Over 70 Over 80

Specified Thickness to 32, to 40, to 48, to 60, to 70, to 80, to 90,
--``,,,,`,``,,,,```,``,````,`,``-`-`,,`,,`,`,,`---

Inch incl incl incl incl incl incl incl

0.0528 to 0.0710, incl 0.006 0.006 0.006 0.007 0.007 -- --
Over 0.0710 to 0.0821, incl 0.007 0.007 0.007 0.007 0.008 0.008 --
Over 0.0821 to 0.0971, incl 0.007 0.008 0.008 0.008 0.009 0.009 0.010
Over 0.0971 to 0.1799, incl 0.008 0.009 0.010 0.010 0.011 0.012 0.012
Over 0.1799 to 0.2299, incl 0.009 0.009 0.010 -- -- -- --

3.1.1 Thickness applies at any point on the sheet not less than 3/8 inch from a cut edge or 3/4 inch from a mill edge.

3.2 Cold Rolled Sheets; Coils and Cut Lengths

See Table 2, (equivalent to ASTM A505-16 Table 6).

Table 2 ± Thickness tolerance, inch, plus and minus; for inch width ranges shown

Over 24 Over 32 Over 40 Over 48 Over 60 Over 70 Over 80

Specified Thickness to 32, to 40, to 48, to 60, to 70, to 80, to 90,
Inch incl incl incl incl incl incl incl
0.0528 to 0.0567, incl 0.005 0.005 0.005 0.005 0.006 -- --
0.0568 to 0.0709, incl 0.005 0.005 0.005 0.006 0.006 -- --
0.0710 to 0.0821, incl 0.005 0.006 0.006 0.006 0.007 0.007 --
0.0822 to 0.0971, incl 0.006 0.007 0.008 0.008 0.009 0.009 0.010
0.0972 to 0.1419, incl 0.007 0.008 0.009 0.010 0.010 0.011 0.012
0.1420 to 0.1799, incl 0.008 0.009 0.010 0.010 0.011 0.012 0.012
0.1800 to 0.2299, incl 0.008 0.009 0.010 -- -- -- --

3.2.1 Thickness applies at any point on the sheet not less than 3/8 inch from a cut edge or 3/4 inch from a mill edge.

Copyright SAE International

Provided by IHS Markit under license with SAE Licensee=Zodiac Seats LLC Engineering/5935306001, User=Hernandez, Juan
No reproduction or networking permitted without license from IHS Not for Resale, 09/24/2018 13:19:22 MDT
 SAE INTERNATIONAL AMS2252ŒE Page 3 of 9
3.3 Hot Rolled Strip; Coils and Cut Lengths, Excluding Crown

See Table 3, (equivalent to ASTM A505-16 Table 13).

Table 3 ± Thickness tolerance, inch, plus and minus; for inch width ranges shown

Over 6 Over 12 Over 15 Over 20

Specified Thickness Up to 6, to 12, to 15, to 20, to 24,
Inch incl incl incl incl incl
0.0528 to 0.0710, excl 0.005 0.005 0.006 0.006 0.006
0.0710 to 0.0971, incl 0.005 0.005 0.006 0.007 0.007
0.0972 to 0.1120, incl 0.005 0.005 0.007 0.008 0.008
0.1121 to 0.1419, incl 0.005 0.006 0.007 0.008 0.008
0.1420 to 0.1718, incl 0.005 0.006 0.007 0.008 0.009
0.1719 to 0.1874, incl 0.006 0.006 0.007 0.009 0.009
0.1875 to 0.2030, incl 0.006 0.006 0.008 0.009 0.009
0.2031 to 0.2299, incl -- 0.007 0.008 0.009 0.009

3.3.1 Thickness applies 3/8 inch from the edge of strip 1 inch or wider and at any point on strip less than 1 inch wide.

3.3.2 Crown Tolerances for Hot Rolled Strip, Coils and Cut Lengths

See Table 4, (equivalent to ASTM A505-16 Table 14).

Table 4 - Crown thickness tolerance, inch

Maximum Additional
Specified Width Thickness at Center
Over 1 to 3-1/2, incl 0.002
Over 3-1/2 to 6, incl 0.003
Over 6 to 12, incl 0.004
Over 12 to 15, incl 0.005
Over 15 to 23-15/16, incl 0.006

3.4 Cold Rolled Strip; Coils and Cut Lengths

See Table 5, (equivalent to ASTM A505-16 Table 18).

Table 5 - Thickness tolerance, inch, plus and minus; for inch width ranges shown
--``,,,,`,``,,,,```,``,````,`,``-`-`,,`,,`,`,,`---

Specified Up to 1 to 3 to Over 6 Over 9 Over 12 Over 16 Over 20

Thickness 1, 3, 6, to 9, to 12, to 16, to 20, to 23-15/16,
Inch excl excl incl incl incl incl incl incl
0.010 0.001 0.001 0.001 0.001 0.001 0.001 0.0015 0.0015
0.011 0.001 0.001 0.001 0.001 0.001 0.0015 0.0015 0.0015
0.012 0.001 0.001 0.001 0.001 0.0015 0.0015 0.0015 0.0015
Over 0.012 to 0.016, incl 0.001 0.001 0.001 0.0015 0.0015 0.0015 0.002 0.002
Over 0.016 to 0.019, incl 0.001 0.001 0.001 0.0015 0.0015 0.002 0.002 0.002
Over 0.019 to 0.025, incl 0.001 0.001 0.0015 0.002 0.002 0.002 0.0025 0.0025
Over 0.025 to 0.028, incl 0.001 0.0015 0.0015 0.002 0.002 0.002 0.0025 0.003
Over 0.028 to 0.034, incl 0.0015 0.0015 0.002 0.0025 0.0025 0.0025 0.003 0.003
Over 0.034 to 0.039, incl 0.002 0.002 0.0025 0.003 0.003 0.003 0.003 0.003
Over 0.039 to 0.049, incl 0.002 0.002 0.0025 0.003 0.003 0.003 0.004 0.004
Over 0.049 to 0.068, incl 0.002 0.002 0.003 0.003 0.003 0.003 0.004 0.004
Over 0.068 to 0.099, incl 0.002 0.002 0.003 0.003 0.003 0.004 0.004 0.004
Over 0.099 to 0.160, incl 0.002 0.003 0.003 0.004 0.004 0.004 0.005 0.005
Over 0.160 to 0.187, incl 0.002 0.0035 0.004 0.004 0.004 0.005 0.006 0.006

Copyright SAE International

Provided by IHS Markit under license with SAE Licensee=Zodiac Seats LLC Engineering/5935306001, User=Hernandez, Juan
No reproduction or networking permitted without license from IHS Not for Resale, 09/24/2018 13:19:22 MDT
 SAE INTERNATIONAL AMS2252ŒE Page 4 of 9
3.4.1 Thickness applies 3/8 inch from the edge of strip 1 inch or wider and at any point on strip less than 1 inch wide.

3.5 Rectangular Sheared Plates

See Table 6, (equivalent to ASTM A6-16 Table 1).

Table 6 - Tolerance, inch, plus; for inch width ranges shown

8 to Over 48 60 to 72 to 84 to 96 to 108 to
Specified Thickness 48, to 60, 72, 84, 96, 108, 120,
Inches incl excl excl excl excl excl excl
0.180 to 0.375, excl 0.030 0.030 0.030 0.030 0.030 0.030 0.030
0.375 to 0.625, excl 0.030 0.030 0.030 0.030 0.030 0.030 0.040
0.625 to 0.750, excl 0.030 0.030 0.030 0.030 0.030 0.040 0.040
0.750 to 1.000, excl 0.030 0.030 0.030 0.030 0.040 0.040 0.050
1.000 to 2.000, excl 0.060 0.060 0.060 0.060 0.060 0.070 0.080
2.000 to 3.000, excl 0.090 0.090 0.090 0.090 0.100 0.110 0.120
3.000 to 4.000, excl 0.110 0.110 0.110 0.110 0.110 0.130 0.140
4.000 to 6.000, excl 0.150 0.150 0.150 0.150 0.150 0.150 0.150

3.5.1 Minus tolerance for all sizes shall be 0.010 inch, plus tolerance shall be as specified in Table 6.

3.5.2 Tolerances apply to measurements made at any point on widths less than 1 inch, at any point not less than 3/8 inch
from a cut edge or not less than 3/4 inch from a mill edge on widths 1 inch and over, and at a point 3/8 to 3/4 inch
from the longitudinal edge of rectangular sheared plates. For thicknesses measured at any other location, the
thickness tolerance may vary by +75% to -0% from the values shown. Regardless of whether thickness tolerances
for sheet and strip are specified equally or unequally, plus and minus, the total tolerance shall be equal to the
arithmetic sum of the tabular plus and minus tolerances (twice the tubular tolerances when specified equally plus
and minus).

4. WIDTH

4.1 Hot Rolled or Cold Rolled Sheets; Cut Edge, Coils and Cut Lengths

See Table 7, (equivalent to ASTM A505-16 Table 8).

--``,,,,`,``,,,,```,``,````,`,``-`-`,,`,,`,`,,`---
Table 7 - Width tolerance, inch

Specified Width Tolerance,

Inches Plus Only
Over 24 to 30, incl 3/16
Over 30 to 50, incl 1/4
Over 50 to 80, incl 5/16
Over 80 3/8

Copyright SAE International

Provided by IHS Markit under license with SAE Licensee=Zodiac Seats LLC Engineering/5935306001, User=Hernandez, Juan
No reproduction or networking permitted without license from IHS Not for Resale, 09/24/2018 13:19:22 MDT
 SAE INTERNATIONAL AMS2252ŒE Page 5 of 9
4.2 Hot Rolled Strip; Coils and Cut Lengths, Except as Noted

4.2.1 Mill Edge

See Table 8, (equivalent to ASTM A505-16 Table 15).

Table 8 - Width tolerance, inch

Specified Width Tolerance,

Inches Plus and Minus
Up to 2, incl 1/32
Over 2 to 5, incl 1/16
Over 5 to 9, incl 3/32
Over 9 to 12, incl 1/8
Over 12 to 20, incl 1/4
Over 20 to 23-15/16, incl 3/8

4.2.1.1 Width measurements on mill edge strip include the mill edge.

4.2.2 Slit Edge

See Table 9, (equivalent to ASTM A505-16 Table 15).

Table 9 - Width tolerance, inch, plus and minus; for inch thickness ranges shown

Specified Width Up to 0.109, Over

Inches incl 0.109
Up to 2, incl 0.010 0.016
Over 2 to 5, incl 0.010 0.020
Over 5 to 9, incl 0.016 0.024
Over 9 to 12, incl 0.016 0.031
Over 12 to 20, incl 0.020 0.031
Over 20 to 23-15/16, incl 0.031 0.031

4.2.3 Sheared Edge, Cut Lengths Only

Tolerance shall be +1/8 inch, -0 for all sizes.

4.3 Cold Rolled Strip; Coils and Cut Lengths, No. 3 Slit Edge

--``,,,,`,``,,,,```,``,````,`,``-`-`,,`,,`,`,,`---
See Table 10, (equivalent to ASTM A505-16 Table 20).

Table 10 ± Thickness tolerance, inch, plus and minus; for inch thickness ranges shown

Over Over Over Over Over

0.0099 to 0.068 to 0.099 to 0.160 to 0.187 to
Specified Width 0.068, 0.099, 0.160, 0.187, 0.2499,
Inches incl incl incl incl incl
3/16 to 1/2, incl 0.005 0.008 0.010 -- --
Over 1/2 to 6, incl 0.005 0.008 0.010 0.016 --
Over 6 to 9, incl 0.005 0.010 0.016 0.020 --
Over 9 to 12, incl 0.010 0.010 0.016 0.020 --
Over 12 to 20, incl 0.016 0.016 0.020 0.031 --
Over 20 to 23-15/16, incl 0.020 0.020 0.020 0.031 --

Copyright SAE International

Provided by IHS Markit under license with SAE Licensee=Zodiac Seats LLC Engineering/5935306001, User=Hernandez, Juan
No reproduction or networking permitted without license from IHS Not for Resale, 09/24/2018 13:19:22 MDT
 SAE INTERNATIONAL AMS2252ŒE Page 6 of 9
4.4 Hot Rolled or Thermally Treated Plate, Sheared

See Table 11, (equivalent to ASTM A6-16 Table 3) for plus tolerance.

Table 11 - Width tolerance, inches, plus; for inch thickness ranges shown

Up 3/8 5/8 1
to to to to
Specified Width Specified Length 3/8, 5/8, 1, 2,
Inches Inches excl excl excl incl
Up to 60, excl Up to 120, excl 3/8 7/16 1/2 5/8
60 to 84, excl Up to 120, excl 7/16 1/2 5/8 3/4
84 to 108, excl Up to 120, excl 1/2 5/8 3/4 1
108 and over Up to 120, excl 5/8 3/4 7/8 1-1/8

Up to 60, excl 120 to 240, excl 3/8 1/2 5/8 3/4

60 to 84, excl 120 to 240, excl 1/2 5/8 3/4 7/8
84 to 108, excl 120 to 240, excl 9/16 11/16 13/16 1
108 and over 120 to 240, excl 5/8 3/4 7/8 1-1/8

4.4.1 Minus tolerance shall be 1/4 inch for all sizes.

4.5 Hot Rolled or Thermally Treated Plate, Gas Cut

See Table 12, (equivalent to ASTM A6-16 Table 8).

Table 12 - Width tolerances, inches

Specified Thickness,
Inches Tolerance
Up to 2, excl 3/4
2 to 4, excl 1
4 to 6, excl 1-1/8
6 to 8, excl 1-5/16
8 to 15, incl 1-1/2

4.5.1 These tolerances may be all under, or may be divided over and under if so specified. Tolerances are applicable to
all widths and lengths.

5. LENGTH

5.1 Hot Rolled or Cold Rolled Sheet

See Table 13, (equivalent to ASTM A505-16 Table 9).

Table 13 - Length tolerance, inches

Tolerance,
Specified Length Plus Only
24 to 30, incl 1/4
Over 30 to 60, incl 1/2
--``,,,,`,``,,,,```,``,````,`,``-`-`,,`,,`,`,,`---

Over 60 to 120, incl 3/4

Over 120 to 156, incl 1
Over 156 to 192, incl 1-1/4
Over 192 to 240, incl 1-1/2
Over 240 1-3/4

Copyright SAE International

Provided by IHS Markit under license with SAE Licensee=Zodiac Seats LLC Engineering/5935306001, User=Hernandez, Juan
No reproduction or networking permitted without license from IHS Not for Resale, 09/24/2018 13:19:22 MDT
 SAE INTERNATIONAL AMS2252ŒE Page 7 of 9
5.2 Hot Rolled Strip

See Table 14, (equivalent to ASTM A505-16 Table 16).

Table 14 - Length tolerance, inches, plus only; for inch width ranges shown

Over 3 Over 6
Specified Length Up to 3, to 6, to 23-15/16,
Inches incl incl incl
Up to 60, incl 1/4 3/8 1/2
Over 60 to 120, incl 3/8 1/2 3/4
Over 120 to 240, incl 1/2 5/8 1
Over 240 to 360, incl 3/4 3/4 1-1/4
Over 360 to 480, incl 1 1 1-1/2
Over 480 1-1/2 1-1/2 1-3/4

5.3 Cold Rolled Strip

See Table 15, (equivalent to ASTM A505-16 Table 22).

Table 15 - Length tolerance, inch, plus only for width ranges shown

Over 12 to
Specified Length Up to 12, 23-15/16,
Inches incl incl
24 to 60, incl 1/4 1/2
Over 60 to 120, incl 1/2 3/4
Over 120 to 240, incl 3/4 1

5.4 Hot Rolled or Thermally Treated Plate, Sheared

See Table 16, (equivalent to ASTM A6-16 Table 3) for plus tolerance.

Table 16 - Length tolerance, inches, plus; for inch thickness ranges shown

Up 3/8 5/8 1
to to to to
Specified Width Specified Length 3/8, 5/8, 1, 2,
Inches Inches excl excl excl incl
Up to 60, excl Up to 120, excl 1/2 5/8 3/4 1
60 to 84, excl Up to 120, excl 5/8 11/16 7/8 1
84 to 108, excl Up to 120, excl 3/4 7/8 1 1-1/8
108 and over Up to 120, excl 7/8 1 1-1/8 1-1/4

Up to 60, excl 120 to 240, excl 3/4 7/8 1 1-1/8

60 to 84, excl 120 to 240, excl 3/4 7/8 1 1-1/4
84 to 108, excl 120 to 240, excl 7/8 15/16 1-1/8 1-3/8
108 and over 120 to 240, excl 1 1-1/8 1-1/4 1-3/8

5.4.1 Minus tolerance shall be 1/4 inch for all sizes.

5.4.2 Tolerances for gas cut lengths are the same as tolerance for gas cut widths (see Table 12) (equivalent to ASTM
A6-16 Table 8).

--``,,,,`,``,,,,```,``,````,`,``-`-`,,`,,`,`,,`---

Copyright SAE International

Provided by IHS Markit under license with SAE Licensee=Zodiac Seats LLC Engineering/5935306001, User=Hernandez, Juan
No reproduction or networking permitted without license from IHS Not for Resale, 09/24/2018 13:19:22 MDT
 SAE INTERNATIONAL AMS2252ŒE Page 8 of 9
6. CAMBER

6.1 Hot Rolled or Cold Rolled Sheet and Strip; Coils and Cut Lengths

See Table 17, (equivalent to ASTM A505-16 Table 11).

Table 17 - Maximum distance from straight edge to sheet or strip

Product Tolerance
Sheet 1/4 inch in any 8 feet
Strip up to 1-1/2 Inches in Width, incl 1/2 inch in any 8 feet
Strip over 1-1/2 to 23-15/16 Inches, incl, in Width 1/4 inch in any 8 feet

6.2 Hot Rolled or Thermally Treated Plate

See Table 18, (equivalent to ASTM A6-16 Table 11).

Table 18 - Maximum distance from straight edge to sheet or strip

Specified Thickness, Specified Width, Tolerance,

Inches Inches Inch
Up to 2, incl All 1/8 x (no. of feet of length)/5
Over 2 to 15, incl Up to 30, incl 3/16 x (no. of feet of length)/5
Over 2 to 15, incl Over 30 1/4 x (no. of feet of length)/5

7. FLATNESS

7.1 Hot Rolled or Cold Rolled Sheets and Strip, As Rolled or Thermally Treated and Flattened

See Table 19, (equivalent to ASTM A505-16 Table 10 for Sheet and comparable to ASTM A505-16 Table 17 for Hot Rolled
Strip).

Table 19 - Flatness tolerance, inch

Specified Thickness Specified Width Variation

Inch Inches from Flat
0.0195 to 0.0567, incl 24 to 36, incl 1/2
0.0195 to 0.0567, incl 36 to 60, incl 3/4
0.0195 to 0.0567, incl Over 60 1

Over 0.0567 to 0.2299, incl 24 to 60, incl 1/2

Over 0.0567 to 0.2299, incl 60 to 72, incl 3/4
Over 0.0567 to 0.2299, incl Over 72 1
--``,,,,`,``,,,,```,``,````,`,``-`-`,,`,,`,`,,`---

Copyright SAE International

Provided by IHS Markit under license with SAE Licensee=Zodiac Seats LLC Engineering/5935306001, User=Hernandez, Juan
No reproduction or networking permitted without license from IHS Not for Resale, 09/24/2018 13:19:22 MDT
 SAE INTERNATIONAL AMS2252ŒE Page 9 of 9
7.2 Plate

See Table 20, (equivalent to ASTM A6-16 Table 14).

Table 20 - Variation from flat, inches; for inch width ranges shown

Up to 36 to 48 to 60 to 72 to 84 to
Specified Thickness 36, 48, 60, 72, 84, 96,
Inches excl excl excl excl excl excl
Up to 0.250, excl 13/16 1-1/8 1-3/8 1-7/8 2 2-1/4
0.250 to 0.375, excl 3/4 15/16 1-1/8 1-3/8 1-3/4 1-7/8
0.375 to 0.500, excl 3/4 7/8 15/16 15/16 1-1/8 1-5/16
0.500 to 0.750, excl 5/8 3/4 13/16 7/8 1 1-1/8
0.750 to 1.000, excl 5/8 3/4 7/8 7/8 15/16 1
1.000 to 2.000, excl 9/16 5/8 3/4 13/16 7/8 15/16
2.000 to 4.000, excl 1/2 9/16 11/16 3/4 3/4 3/4
4.000 to 6.000, excl 9/16 11/16 3/4 3/4 7/8 7/8
6.000 to 8.000, excl 5/8 3/4 3/4 15/16 1 1-1/8

7.2.1 The longer dimension specified is considered the length. Variations in flatness along the length shall not exceed

--``,,,,`,``,,,,```,``,````,`,``-`-`,,`,,`,`,,`---
the amounts in the above table for plates 12 feet and under in length or in any 12 feet of longer plates.

7.2.2 When the longer dimension is less than 36 inches, the variation in flatness shall be not greater than 3/8 inch. When
the longer dimension is 36 to 72 inches, the variation shall not exceed 0.75 times the amount shown for the specified
width.

7.2.3 The flatness variation across the width shall not exceed the tolerance specified for the length for the specified width.

8. NOTES

8.1 Revision Indicator

A change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not
editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title
indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original
publications, nor in documents that contain editorial changes only.

PREPARED BY AMS COMM,77((³(´

Copyright SAE International

Provided by IHS Markit under license with SAE Licensee=Zodiac Seats LLC Engineering/5935306001, User=Hernandez, Juan
No reproduction or networking permitted without license from IHS Not for Resale, 09/24/2018 13:19:22 MDT