8DH10 Katalog en

Medium-Voltage
Switchgear
Switchgear Catalog HA 41.11
2003
Type 8DH10 up to 24 kV,
SF6-Insulated, Extendable Supersedes:
Catalog HA 41.11 · 2001
Switchgear Type 8DH10 up to 24 kV, SF6-Insulated, Extendable
Contents Application, Requirements
Page Features
8DH10 switchgear is a factory- Quality and environment
Application, Requirements assembled, type-tested, three- Quality and environmental
Features, typical uses 2 and 3 phase, metal-enclosed, metal-clad management system acc. to
single-busbar switchgear for in- DIN EN ISO 9001 and
Technical Data door installation: DIN EN ISO 14001
Electrical data, filling pressure, • Up to 24 kV
temperature 4 Personal safety
• Feeder currents up to 630 A
Switchgear installation, shipping data 5 and 6 • Safe-to-touch and hermetically
• Busbar currents up to 1250 A
sealed primary enclosure
Product Range
Typical uses • HV HRC fuses and cable sealing
Product range overview 6 to 13
8DH10 switchgear is used – even ends are only accessible when
Design under severe environmental con- the outgoing feeders are earthed
Panel design 14 and 15 ditions – for power distribution in • Operation is only possible when
secondary distribution systems, the enclosure is closed
Components e.g. in • Logical mechanical interlocking
3AH vacuum circuit-breakers 16 and 17 ■ Substations, customer trans- • Capacitive voltage detection sys-
Three-position switch-disconnectors 18 fer substations, distribution sub- tem for verification of safe isola-
stations and switching substation from supply
Busbars 19
tions of power supply and
Transformers 20 to 25 public utilities • Earthing of outgoing feeders by
Cable connection 26 means of make-proof earthing
Low-voltage equipment 27
■ Industrial plants, such as: switches
• Wind power stations
Dimensions • High-rise buildings Security of operation
Individual panels, panel blocks 28 to 32 • Airports • Hermetically sealed primary
Metering panel combinations 31 and 33 enclosure independent of
• Lignite open-cast mines environmental effects (dirt,
Floor openings and fixing points 34 to 37
Cable-connection fittings 38 • Underground railway stations moisture and small animals) –
sealed for life:
• Sewage treatment plants
Standards – Welded switchgear vessel
• Port facilities – Welded-in bushings and operating
Standards, specifications, guidelines 39 mechanism
• Traction power supply systems
Appendix • Automobile industry • Maintenance-free operating
mechanism parts
Notes 39 • Petroleum industry (IEC 60 694/VDE 0670, Part 1000)
Further Information • Chemical industry • Switch operating mechanisms
See Catalog HA 40.1 • Cement industry accessible outside the switchgear
vessel
• Unit-type heating power stations
• Switchgear interlocking by
• Textile, paper and food
means of logical mechanical
industry
interlocking
• Emergency power supply
• Mechanical switch position
installations
indications integrated in the
mimic diagram
Modular design
• Individual panels and panel Cost-efficiency
blocks can be freely combined
Extremely low “life-cycle costs”
and extended – without the need
and extremely high availability
for work involving SF6 gas
throughout the entire product
• Low-voltage compartments can service life as a result of:
be supplied in two overall heights
• Maintenance-free concept
and are wired to the panel by
means of plug-in connections • Climatic independence
• Minimum space requirement
Reliability
• Maximum availability
• Type and routine-tested
• Standardized and manufactured Security of investment
using numerically controlled Innovative developments, such as:
machines
• Modular design
• More than 350,000 8DJ/ 8DH
panels in operation worldwide • Extendability of the switchgear
for many years without gas work on site
• 3AH maintenance-free vacuum
© Siemens AG 2003
circuit-breakers
• SIPROTEC protection relay family
2 Siemens HA 41.11 · 2003
Application
Typical uses
Technical features
• Maintenance-free
• Climate-independent
• Three-pole primary enclosure,
metal-enclosed, metal-clad
• Insulating gas SF6
• Gas-tight, welded switchgear
R-HA41-013a eps
vessel made of stainless steel
with welded-in bushings for
electrical connections and
mechanical components
• Three-position switch-discon-
nector with load-break and
make-proof earthing function
• Cable connection for bushings
with outside cone
• Connection by means of cable
plugs
– In ring-main feeders and
circuit-breaker feeders with
bolted contact (M16)
Example
– In transformer feeders with Customer transfer switchgear
plug-in contact
• Option: Connection with conven-
tional cable sealing ends
– For thermoplastic-insulated
cables via elbow adapter
AKE 20/ 630 (make Siemens)
– For paper-insulated mass-
impregnated cables via commer-
cially available adapter systems
• Easy installation
• Option: Pressure absorber
system
– Maintenance-free
– For rated short-time withstand
current Ik £ 20 kA
– For single and multi-panel
combinations of 700 mm to
2000 mm width (for panel type
ME1 with max. 1 adjacent panel)
– With 300 mm high pressure
absorber duct below the
switchgear
– With 115 mm deep pressure
absorber duct for pressure relief
upwards
– Possible for switchgear with
standard cable compartment
cover,
R-HA41-015 eps
option: 105 mm or 300 mm

deeper cable compartment cover
possible
– Option: Free-standing Application
arrangement, for switchgear Customer transfer substation in an
height 2300 mm and with rear accessible switchgear building
cover (transformers, medium-voltage and
low-voltage in a factory-assembled
For further information concerning building)
R-HA41-014 eps
the pressure absorber system,

please refer to page 37
and to Catalog HA 40.1
Standards
Application
See page 39
Power supply of high-rise buildings
Siemens HA 41.11 · 2003 3

Technical Data
Filling pressure,
Electrical data temperature
Rated voltage Ur kV 7.2 12 15 17.5 24 Pressure values at 20 °C

Rated insulation Rated short-duration power-frequency kV 20 28 36 38 50 Rated filling 1500 hPa
level withstand voltage Ud pressure pre (absolute)
Rated lightning impulse withstand voltage Up kV 60 75 95 95 125 for insulation
Rated frequency fr Hz 50/60 50/60 50/60 50/60 50/60 Minimum operating 1300 hPa
pressure pme (absolute)
Rated normal for busbar (standard) A 630 630 630 630 630 for insulation
current Ir 1)
(not for billing for busbar (option) A 1250 1250 1250 1250 1250
metering panels
type ME1) Ambient temperature T
Panels without – 40 °C
secondary equipment to +70 °C
Ring-main panel type RK, bus sectionalizer panel type LT2, cable connection panel type K Panels with secon- – 5 °C
dary equipment and to +55 °C
Rated normal for feeder (for panel types RK … and K …) A 400, 630 400, 630 400, 630 400, 630 400, 630 circuit-breaker panels
current Ir 1) for bus sectionalizer panel type LT2 A 400, 630 400, 630 400, 630 400, 630 400, 630
Rated short-time for switchgear with tk = 1 s up to kA 20 25 20 25 20 25 20 25 20
withstand current Ik for switchgear with t = 3 s (option) up to kA 20 – 20 – 20 – 20 – 20
k
Rated peak withstand current Ip up to kA 50 63 50 63 50 63 50 63 50
Rated short-circuit making current Ima up to kA 50 63 50 63 50 63 50 63 50
Transformer panel type TR

Rated normal for feeder 2) A 200 200 200 200 200
current Ir 1)
withstand current Ik for switchgear with t = 3 s up to kA 20 – 20 – 20 – 20 – 20
k
Rated peak withstand current Ip 2) up to kA 50 63 50 63 50 63 50 63 50
Rated short-circuit making current Ima 2) up to kA 25 25 25 25 25 25 25 25 25
Reference dimension “e” of the HV HRC fuse links mm 292 3) 292 442 442 442
Circuit-breaker panel type LS, bus sectionalizer panel type LT1
Rated normal for feeder (for panel types LS …) A 400, 630 400, 630 400, 630 400, 630 400, 630
current Ir 1) for bus sectionalizer panel type LT1 A 400, 630 400, 630 400, 630 400, 630 400, 630
k
Rated short-circuit breaking current Isc 4) up to kA 20 25 20 25 20 25 20 25 20
Electrical at rated normal current 10 000 operating cycles
service life of
3AH vacuum at rated short-circuit breaking current 50 make-break operations
circuit-breakers
Busbar earthing panel type SE, busbar voltage metering panel type ME3

k
1) The rated normal currents apply

to ambient temperatures of
Billing metering panels type ME1 and type ME2 max. 40 °C. The 24-hour-mean
for transfer up to A 630 630 630 630 630 value is max. 35 °C (according to
Rated normal IEC 60 694 / VDE 0670, Part 1000)
current Ir 1) for feeder (cable con. panel type ME1-K) up to A 630 630 630 630 630
2) Depending on the HV HRC fuse
for busbar metering up to A 630 630 630 630 630 link, observe the max. cut-off
for switchgear with tk = 1 s up to kA 20 25 20 25 20 25 20 25 20 current of the HV HRC fuse links
Rated short-time
withstand current Ik for switchgear with t = 3 s up to kA 20 – 20 – 20 – 20 – 20 3) Extension tube (150 mm long)
k
required additionally for fuse
Rated peak withstand current Ip up to kA 50 63 50 63 50 63 50 63 50 mounting 442 mm
4) For 3AH vacuum circuit-breakers
4 Siemens HA 41.11 · 2003

Switchgear installation
Room planning
Switchgear installation
Wall-standing arrangement
– Single row
– Double row (for face-to-face
aaarrangement)
Room dimensions
See opposite dimension
drawings
Door dimensions
The door dimensions depend
on the
– Number of panels in a
transport unit
– Design with or without
low-voltage compartment
Switchgear fastening
• For floor openings and fixing
points of the switchgear,
see pages 34 and 35
• Foundations:
– Steel structure
– Steel-reinforced concrete
Panel dimensions
See pages 28 to 32
Weight
The weight of a panel depends
on the extent to which it is
equipped (e.g. with motor
operating mechanism, voltage
transformer). For details,
please refer to page 6.
* For free-standing arrangement

and with pressure absorber duct:
Switchgear 2300 mm high
as standard (with end walls,
rear wall and front cover sheets)
20
2000
1
aa Room planning
HA41-2286e eps
Switchgear room
Cable
basement
Side view
Top view
³15
775
1070
10
10
Switchgear installation with

standard panels
1 Relief opening
2 Room height
³1000
³1000
³1000
³ 50
³ 50
3 Panel depth of the standard

panel (may be 15 mm deeper
for free-standing arrangement,
depending on the panel design)
4 Control aisle
5 Panel depth of panels with
deep cable compartment
cover
6 Deep cable compartment
cover
7 Standard cable compartment
cover
8 Foundation
³ 2400
>600
5
6
7
8
9
10
11
12
16
17
18
2300*
19
19
10 Height of the cable

Switchgear room
Top view
115
Side view
³15
*
890
828
834
Cable basement
Technical Data
300
Switchgear installation with rear-side

pressure absorber duct (option)
9 2nd cable connected by means

of double T-plugs in conjunc-
tion with deeper floor opening
and design with deep cable
compartment cover
basement corresponding to
the cable bending radius
11 Cable
12 Direction of pressure relief
13 Option:
Pressure absorber duct
14 Base height of the pressure
absorber duct beneath the
panel
15 Depth of the pressure absorber
duct behind the panel
16 Wall distance
17 End wall
18 Panel width
HA41-2287e eps
19 Width of the pressure absorber duct

– 700 mm for panel combinations
– Approx. 850 mm for metering
panels type ME1
20 Standard:
Low-voltage compartment
for circuit-breaker panels
Option:
– Low-voltage compartment
for all other panel types or
– Front cover
Siemens HA 41.11 · 2003

20
12
13
14
15
13
5
Technical Data
Shipping data Product range overview

Individual panel, panel block Type Panel or panel Transport unit (including packing) for standard panels Designation of the
or combinations combination (without pressure absorber system) individual panels
thereof for standard switchgear and panel blocks
(without pressure relief duct) Width Net Width Height Depth Volume Gross
B1 weight 1) B2 T2 weight
mm approx. kg m m m m3 approx. kg
without / with without / with without / with without/with
LVC */LVC * LVC */LVC * LVC */LVC * LVC */LVC *
Transport of individual panels

Ring-main panel (standard) RK 350 150 / 210 0.70 1.60 / 2.20 1.10 1.23 / 1.69 210 / 270
RK1 350 180 / 240 0.70 1.60 / 2.20 1.10 1.23 / 1.69 240 / 300
Cable panel (standard) K 350 145 / 205 0.70 1.60 / 2.20 1.10 1.23 / 1.69 205 / 265
Transformer panel TR 500 180 / 240 0.70 1.60 / 2.20 1.10 1.23 / 1.69 240 / 300
Circuit-breaker panel (standard) LS1 500 – / 260 0.70 – / 2.20 1.10 – / 1.69 – / 320
LS2 500 – / 380 0.70 – / 2.20 1.10 – / 1.69 – / 440
Bus sectionalizer panel LT1 500 – / 280 0.70 – / 2.20 1.10 – / 1.69 – / 340
LT1-V 500 – / 380 0.70 – / 2.20 1.10 – / 1.69 – / 440 Individual panels
LT2 500 150 / 210 0.70 1.60 / 2.20 1.10 1.23 / 1.69 210 / 270 Ring-main panel
Busbar earthing panel SE1 350 150 / 210 0.70 1.60 / 2.20 1.10 1.23 / 1.69 210 / 270
Cable panel without
SE2 500 250 / 310 0.70 1.60 / 2.20 1.10 1.23 / 1.69 310 / 370
earthing switch
Busbar voltage metering panel ME3 500 250 / 310 0.70 1.60 / 2.20 1.10 1.23 / 1.69 310 / 370
Cable panel with make-proof
Billing metering low structure ME1 ** 850 250 / 310 1.08 1.60 / 2.20 1.10 1.90 / 2.61 310 / 370 earthing switch
panels, air- with combined instru- ME2 600 390 / 450 1.08 1.60 / 2.20 1.10 1.90 / 2.61 450 / 510
insulated Transformer panel
ment transformers
Transport of panel blocks Transformer panel with

plug-in voltage transformer
Ring-main panel block R-B2 700 280 / 400 1.08 1.60 / 2.20 1.10 1.90 / 2.61 340 / 460
Circuit-breaker panel
R-B3 1050 400 / 580 1.40 1.60 / 2.20 1.10 2.46 / 3.40 470 / 650
Transformer panel block T-B2 1000 320 / 440 1.40 1.60 / 2.20 1.10 2.46 / 3.40 390 / 510 Circuit-breaker panel with metal-enclosed
T-B3 1500 480 / 660 2.03 1.60 / 2.20 1.10 3.57 / 4.91 560 / 740 busbar voltage transformers
Ring-main/transformer panel block RT-B2 700 300 / 420 1.08 1.60 / 2.20 1.10 1.90 / 2.61 360 / 480 Bus sectionalizer panel
with vacuum circuit-breaker
2RT-B3 1050 450 / 630 1.40 1.60 / 2.20 1.10 2.46 / 3.40 520 / 700
Bus sectionalizer panel
3RT-B4 1400 580 / 820 2.03 1.60 / 2.20 1.10 3.57 / 4.91 660 / 900
Cable connection/ KT-B2 700 300 / 420 1.08 1.60 / 2.20 1.10 1.90 / 2.61 360 / 480
transformer panel block Busbar earthing panel
Transport of combinations of different individual panels or panel blocks Busbar voltage metering panel
Comprising Overall width B3 B2 T2
– a number of individual panels or Billing metering panel
£ 850 mm 1.08 1.60 / 2.20 1.10 1.90 / 2.61 2) + 60 ***
– 1 panel block or
– a number of panel blocks or £ 1200 mm 1.40 1.60 / 2.20 1.10 2.46 / 3.39 2) + 70 ***
2) + 85 *** Billing metering busbar connection
– individual panels with panel blocks £ 1800 mm 2.03 1.60 / 2.20 1.10 3.57 / 4.91
2) + 100 ***
panel for cable connection
£ 2350 mm 2.55 1.60 / 2.20 1.10 4.49 / 6.17
Billing metering panel
Transport units for shipping (plan view) with combined transformers
1 T1 = Depth of individual Panel blocks

panel or of panel block
Ring-main panel block
2 Individual panel or panel
block, dimension B1 x T1
Transformer panel block
3 Transport unit,
dimension B2 x T2
Ring-main/transformer panel block
4 B3 = Overall width of
combination of different
With individual panel individual panels
or panel block or panel blocks
With combinations of different individual
panels and/or panel blocks 5 B2 = Width of the
(option: panels screwed on and busbars mounted) transport unit
Cable connection/transformer panel block
without earthing switch
1) The net weight depends on 2) Sum of the * Low-voltage compart- ** The weights depend on the Cable connection/transformer panel block
the extent to which it is equipped net weights ment, 600 mm high, weights of the mounted (cable panel with make-proof
(e.g. with current transformers, of individual weight approx. 60 kg transformers earthing switch)
motor operating mechanism, deep panels and / depending on the panel
cable compartment cover) and or panel blocks type and on the extent *** Packing weight
is therefore given as mean value to which it is equipped
6 Siemens HA 41.11 · 2003

Product Range
Equipment features
Panel Type r
to h
width • Basic equipment r m n ec itc
to is n r or sw
Additional equipment c n o f g or
° e ha isc to
(option), further additional onn ec -d n ec NO thin ect
h 2 r nn
equipment on request isc m itc on d ea
h -d tin
g
s w isc an of isco on r ker
d ” o
– Not available itc on er
a nt n h- D pr h-d iti to
sw ed op ism tme itio itc HE ke- itc -pos r itch n ec brea
s
n ew e n r po sw R T a sw e e sw on uit-
s itio s cr e
th ha pa
c m ee- al ion /EA d m ion thre reak ng isc circ
o / v e r c t n t i d
-p r e o co h ri si ED . a si en it-b rth h h-
ee lac ab g m al r t ct o c o c itc um
hr ove in p p. atin in r fo ele e-p LOS -dis e-p twe ircu f ea wit sw acu ase
t m e re
to t h “C itch thr l b m e e c o s r
r
fo ent ked
c om er er ro to n v le
l c op s t ica mo r t r r e u -p tion ica itio for re
ism rtm r lo
c
ina he e a ind r re n fo C fo n sw fo pan acu ake osi ind pos m ted t
n rm t h e fo io N io ism r v m -p lt e- is ra n
ha mpa ove t te ls in nic vic O) icat +1 osit an ake and for ree fau hre han ope tme
ec c s er h e - c ps
m e co ent cke e a ina tag
e -r s (1N ind 2NO e-p ec t-br tor out r th rth or t me er par r lam
g l a
r ic h m l fo e ( e m i c - o a f m e c
tin ab tm b er vo y- tch ic h hr g cu ne lock ce f or e out ting for com cov le
ra r c ar le e n e t w- se ad wi erv itc r t tin cir on i t - a s e e b
ope fo mp cab tag tag e lo lea . re g s r-s sw ) fo era in isc ing dev cui lock per tran tag tag d ca ry ent
l ck o s l l t re an llin y-fo iary N” rop ock h-d rth ng -cir ng r o nt- vol vol te nda pm
ua lo le c il a -vo -vo ara nt h a il E o l c a i rt i o e - - n i
an nter ab -ra ow ow ep hu ec ign read ux OP ot nter wit e-e ock ho los ot urr ow ow ou ecoequ
M I C C L L S S M S A “ M I s D L S C M C L L M S
Column No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
• • – • • – – – • – – – –
350 RK-. . ., RK1
• • – – • – – – •
° ° ° – –
° °– ° – –
° ° °– °
350 RK-U
– – • • • – – – •
° °– °– – –
°– °– – –
° ° °
350 K
– – • – • – – – •
° – – – –
°
– – – – –
° ° °– °
350 K-U
– – – –
° – – –
° ° °
350 K •
•
•
• –
•
–
•
• – – –
•
•
° ° – – –
° °– –– –
–
–
–
° ° °– °
350 K-U
– – –
° ° –
° ° ° °
500 TR •
•
•
• –
•
– –
•
• –
° •
•
° ° ° –
° ° –– –– –
–
–
–
° ° °– °
500 TR-U
• • – • – • –
° •
° ° ° –
° ° – – – –
° ° °
500 TR-V
• • – – – • –
° •
° ° ° –
° ° – – – –
° ° °– °
500 TR/V
• • – • – – –
° •
° ° ° °– ° °• °– °
500 LS1-. . .
• • – – – – –
° •
° ° ° ° –
° °– ° ° ° • –
°– °
500 LS1-U
• • – • – – –
° •
° ° ° ° –
° ° ° ° • –
°
500 LS2-. . .
• • – – – – –
° •
° ° ° ° –
° °– ° ° ° • –
°– °
500 LS2-U
• – • – – – –
° •
° ° ° ° –
°• – °– ° ° • – –
°
500 LT1
• – • – – – –
° •
° ° ° ° – • – –
° ° • – –
°
500 LT1-V
• – • – • – –
°– •
° ° ° °– –
° °
• – – – – –
°
500 LT2
° ° ° ° ° °
• • – – • – – – • – – – • – – – – –
350 SE1
• • – – • – – – •
° ° – – – • – – – –
° ° –
°
500 SE2
• – • – • – – – •
° ° – – – – – –
° ° –
°
500 ME3
° ° ° ° ° ° °
– – – – – – – – – – – – – – – – –
850 ME1
– –
•
• • – –
•
• – – – – – – – – – – – –
° ° – °
850 ME1-K
– – • – – – • – – – – – – – – – – – –
° ° °– °
850 ME1-S
– – • • – – • – – – – – – – – – – – –
° ° °
850 ME1-KS
– – • – – – – – – – – – – – – – – – –
° ° °– °
600 ME2
° ° °
Column No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
– – – – •1) 1) – – – – –
• • • •
700 R-B2
• • – • • – – – •1)
°) 1
° ° – –
° ° – – –
° ° ° °
1050 R-B3
• • – • – – – •1)
°) 1
° ° –
° °– – – –
° ° ° °
1000 T-B2
• • – • – – –
° •1)
°) 1
° ° –
° ° – – – –
° ° ° °
1500 T-B3
• • – • • – –
°– •1)
°) 1
° ° –
°– ° – –
° ° ° °
700 RT-B2
RK
• • – • 2) – – 1)
°)
1
° ° –
° °– °– – –
° ° ° °
T
• • – • • – –
°– •1) 1
° ° –
°– ° – –
° ° ° °
1050 2RT-B3
RK
• • – • 2) – – 1)
°)
1)
° ° –
° °– °– – –
° ° ° °
T
• • – • • – –
°– •)1 1)
° ° –
°– ° – –
° ° ° °
1400 3RT-B4
RK
• • – • 2) – – 1)
°
1)
° ° –
° °– °– – –
° ° ° °
T
– – • • • – –
°– • 1) 1)
°– °– –
°– °– – – –
° ° ° °
700 KT-B2
K
• – – • 2) – – 1)
°
1) –
°– – – –
° ° ° °
T
• • – • • – –
°– •1) 1
°– °– –
°– °– – – –
° ° ° °
700 KT-B2
K
• • – • 2) – – 1)
°)
1) –
°– – – –
° ° ° °
T
° ° ° ° ° ° ° ° °
1) The equipment applies to the entire panel block, 2) Low-voltage terminals arranged in the low-voltage niche
but it is located in the first feeder panel from the left of the ring-main or cable feeder
Siemens HA 41.11 · 2003 7

Product Range
Ring-main panels, cable and transformer panels as individual panels
Ring-main panels Cable panels Transformer panels

as feeder panels as feeder panels as feeder panels
Three-position
option Type RK option Type K option Type TR switch-disconnector
350 mm wide 350 mm wide 500 mm wide
HA41-2213_1c eps
HA41-2218_1c eps
HA41-2223_1c eps
Type RK1
500 mm wide
HV HRC fuse
option option option
Capacitive
voltage detection
system
**
option Type RK-K * option Type K-K * option Type TR-V *
HA41-2219_1d eps
HA41-2214_1d eps
HA41-2224_1c eps
Cable-type current
for 2nd cable for 2nd cable with plug-in transformer
voltage trans-
formers
option option option 4MT8 plug-in voltage

transformer at the
cable connection
** **
4MT8 plug-in
voltage transformer
option Type RK-A * option Type K-A * option Type TR-V * at the connection
HA41-2220_1c eps
HA41-2215_1c eps
HA41-2225_1c eps
with plug-in with plug-in with plug-in

surge surge voltage trans-
arresters arresters formers in-
stead of cable Cable (not
connection included in the
option option
scope of supply)
2nd cable (not

included in the
scope of supply)
as transfer panels as transfer panels as transfer panels
option Type RK-U Type K-U option Type TR-U Plug-in

HA41-2216_1c eps
HA41-2226_1c eps
surge arrester
for transfer option for transfer for transfer
HA41-2278e eps
to the right to the right to the right

HA41-2221_1c eps
Make-proof
earthing switch
option Type RK-U Type K-U option Type TR-U

HA41-2227_1c eps
HA41-2217_1c eps
for transfer for transfer for transfer * Deep cable

option
to the left compartment
to the left to the left
HA41-2222_1c eps
cover required
** Cable-type
current
transformer
on the
2nd cable:
For 300 mm
deeper
cable
compartment
cover
8 Siemens HA 41.11 · 2003
Product Range
Ring-main panels, cable and transformer panels in panel blocks
Ring-main panel blocks Ring-main/transformer panel blocks

Designs and options for each panel, see page 8 Designs and options for each panel, see page 8
RK RK RK TR *
Three-position
Type R-B2 Type RT-B2
HA41-2228_1c eps
HA41-2232_1c eps
switch-disconnector
700 mm wide 700 mm wide
consisting of consisting of
2 ring-main panels 1 ring-main panel and
1 transformer panel
HV HRC fuse
Capacitive
voltage detection
system
RK RK RK RK RK TR *
HA41-2278e eps
Type R-B3 Type 2RT-B3
HA41-2233_1c eps
HA41-2229_1c eps

consisting of consisting of Cable (not
3 ring-main panels 2 ring-main panels and included in the
1 transformer panel scope of supply)
RK RK RK TR *
Type 3RT-B4
HA41-2234_1c eps
Transformer panel blocks 1400 mm wide
Designs and options for each panel, see page 8 consisting of

3 ring-main panels
TR TR and
Type T-B2
HA41-2230_1c eps
1 transformer
1000 mm wide panel
consisting of
2 transformer panels
Cable connection/transformer panel block

Designs and options for each panel, see page 8
TR TR TR K TR *
Type T-B3 Type KT-B2
HA41-2235_1d eps
HA41-2231_1c eps

consisting of consisting of
3 transformer 1 cable connection panel
panels 1 transformer panel
Designs Designs
• Busbar connection system for connection of individual • Busbar connection system for connection of individual
panels or panel blocks: Arranged in the left-hand panel of the panels or panel blocks: Arranged in the left-hand panel of the
panel block (therefore extendable at a later date) panel block (therefore extendable at a later date)
• Only either the left-hand or the right-hand panel of the panel block • Only either the left-hand or the right-hand panel of the panel block
can be designed as a transfer panel with busbar connection can be designed as a transfer panel with busbar connection
• Panel blocks are also available without a busbar connection • Panel blocks are also available without a busbar connection
system (extendable at a later date only via the cable feeder) system (extendable at a later date only via the cable feeder)
* A plug-in voltage transformer cannot be provided at the connection
Siemens HA 41.11 · 2003 9

Product Range
Circuit-breaker panels as individual panels
Circuit-breaker panels Circuit-breaker panels with metal-enclosed

busbar voltage transformers
as feeder panels as feeder panels Vacuum
circuit-breaker
option option option option
HA41-2238_1d eps
HA41-2244_1d eps
HA41-2236_1d eps
HA41-2242_1d eps
Three-position
switch-disconnector
** **
Capacitive
voltage detection
system
Type LS1 Type LS1-K * Type LS2 Type LS2-K *
500 mm wide 500 mm wide 500 mm wide 500 mm wide **
Basic panel for 2nd cable Basic panel for 2nd cable
Three-phase current
transformer on the
bushing or cable-type
current transformer
option on the cable
option option option
HA41-2239_1c eps
HA41-2243 _1c eps

HA41-2237_1c eps
HA41-2245_1c eps
4MT8 plug-in voltage
transformer at the
cable connection
4MT3 plug-in
voltage
transformer
Type LS1-A * Type LS1-V * Type LS2-A * Type LS2-V * at the busbar
500 mm wide 500 mm wide 500 mm wide 500 mm wide
with plug-in with plug-in with plug-in with plug-in
surge arresters voltage trans- surge arresters voltage trans-
or limiters formers or limiters formers
Cable (not
included in the
scope of supply)
as transfer panels as transfer panels

option Type LS1-U option Type LS2-U 2nd cable (not
500 mm wide 500 mm wide included in the
HA41-2240_1c eps
HA41-2246_1c eps
scope of supply)
for transfer for transfer
to the right to the right
HA41-2278e eps
option option Plug-in

surge arrester
or limiter
option Type LS1-U option Type LS2-U

HA41-2247_1c eps
HA41-2241_1c eps
for transfer for transfer * Deep cable

to the left to the left compartment
cover required
option option ** Cable-type
current
transformer
on the
2nd cable:
For 300 mm
deeper
cable
compartment
cover
10 Siemens HA 41.11 · 2003
Product Range
Bus sectionalizer panels, busbar earthing panels and busbar voltage metering panel as individual panels
Bus sectionalizer Busbar earthing Busbar voltage metering

panels panels panel
Vacuum
circuit-breaker
HA41-2252_1a eps
option
HA41-2254_1c eps
HA41-2248_1b eps
Three-position
switch-disconnector
option
Capacitive
voltage detection
system
Type LT1 Type SE1 Type ME3
Cable-type
with vacuum current trans-
circuit-breaker former on the
screened busbar
option
HA41-2249_1d eps
Make-proof
earthing switch
option
4MT3 plug-in
voltage
transformer
at the connection
HA41-2278e eps
Type LT1-V
500 mm wide 4MT3 plug-in
with vacuum voltage
circuit-breaker and transformer
plug-in voltage at the busbar
transformers
HA41-2253_1c eps
option
HA41-2250_1b eps
option
Type LT2 Type SE2

with plug-in,
metal-enclosed
voltage
transformers
Siemens HA 41.11 · 2003 11

Product Range
Air-insulated metering panels as transfer panels
Billing metering panels Billing metering panels as end Billing metering panels for
(standard) panels, for cable connection busbar connection
low structure low structure low structure Current trans-
option option former, cast-resin
option P1 P2 insulated
HA41-2258_1b eps
HA41-2262_1a eps
HA41-2266_1b eps
P2 P2
Voltage transformer,
1) cast-resin insulated
P1 P1
or on request:
cast-resin insulated,
with HV HRC fuses
Scheme 1 Scheme 1 Scheme 1
Type ME1, 850 mm wide Type ME1-K, 850 mm wide Type ME1-S, 850 mm wide
for transfer to the right for transfer to the right for busbar metering Voltage trans-
former, cast-resin
insulated
option option option P1 P2
HA41-2263_1a eps
HA41-2267_1b eps
HA41-2259_1b eps
Fixed points
1) for busbar
earthing
P2 P2
HA41-2278d eps
P1 P1
Cable (not
included in the
Scheme 2 Scheme 2 Scheme 2 scope of supply)
Type ME1, 850 mm wide Type ME1-K, 850 mm wide Type ME1-S, 850 mm wide P1 and P2
for transfer to the right, for transfer to the right, for busbar metering, are terminal
transformer terminals transformer terminals transformer terminals designations
interchanged interchanged interchanged of the current
transformer
HA41-2264_1a eps
HA41-2436_1 eps
HA41-2260_1b eps
1)
P1 P1
P2 P2
for transfer to the right for transfer to the right for busbar metering,
transformer terminals
interchanged
HA41-2265_1a eps
HA41-2437_1 eps
HA41-2261_1b eps
P1 P1
1)
P2 P2
for transfer to the right, for transfer to the right, for busbar metering,
transformer terminals transformer terminals transformer terminals
interchanged interchanged interchanged
Note Note
Schemes 1 to 4 also feasible Schemes 1 to 4 also feasible
for transfer to the left for transfer to the left
12 Siemens HA 41.11 · 2003

Product Range
Air-insulated metering panels as transfer panels
Billing metering panels as end Billing metering panels Billing metering panels *
panels, for cable connection as individual panels, for cable with metal-enclosed
low structure connection, low structure combined transformers Current trans-
former, cast-resin
HA41-2276_1d eps
option option P1 P2 insulated
HA41-2268_1d eps
HA41-2473 eps
2)
P2 P2 Voltage transformer,
3)
cast-resin insulated
P1 P1 or on request:
1) 1)
cast-resin insulated,
with HV HRC fuses
Type ME1-KS, 850 mm wide Type ME1-KK, 850 mm wide Type ME2, 600 mm wide
4MK plug-in
for transfer to the right for cable connection for transfer to the right combined current
transformer,
metal-enclosed
HA41-2277_1d eps
option option P1 P2 3)
HA41-2269_1d eps
HA41-2474 eps
2)
1) 1) 4MK plug-in
3)
combined voltage
P2 P2 transformer,
metal-enclosed
P1 P1
Fixed points
Scheme 2 Scheme 2 Scheme 2 for busbar
earthing
HA41-2278e eps
for transfer to the right, for cable connection, for transfer to the right,
Cable (not
HA41-2438_1b eps
option option P2 P1 included in the

HA41-2270_1d eps
HA41-2475 eps
scope of supply)
1) 2)
1) P1 and P2
are terminal
P1 3)
P1 designations
of the current
P2 P2 transformer
for transfer to the right for cable connection for transfer to the left
HA41-2439_1b eps
option option P2 P1
HA41-2271_1d eps
HA41-2476 eps
2)
P1 P1
3)
P2 P2
1) 1)
for transfer to the right, for cable connection, for transfer to the left,
Note * Mainly for connection to

bus sectionalizer panels
Schemes 1 to 4 also feasible
LT1, LT1-V and LT2
as left-hand end panel
for transfer to the left
Siemens HA 41.11 · 2003 13

Design
Panel design (examples)
Ring-main panel Section Transformer panel Section
HA41-2280c eps
HA41-2279d eps
61 1 61
1
2 31
32 34
33
3 23 3
11 11
4 38 23
12 12
5 24 5 35
13 13
6 6
14 7 14
7 15 15
15 15
8
9 25 9 36
16 16
17 17 37
26
18 18
10 27 10 27
19 28 19 28
20 20
29 29
21 21
22 22
Type RK Type TR
Legend for pages 14 and 15

Billing metering panel, air-insulated Section 1 Option: Low-voltage compartment
2 Niche for optional low-voltage equipment,
HA41-2281d eps
with hinged cover

3 Switch position indication for load-break
function“CLOSED – OPEN”
61
1 4 Switch position indication for earthing
function“OPEN – EARTHED”
5 Ready-for-service indicator
2 2
6 Rating plate
40 7 Mimic diagram
11 8 Option: Short-circuit / earth-fault indicator
9 Sockets for voltage detection system
39
39
10 Arrangement of the busbars
6 11 Feeder designation label
12 Option: Locking device for three-position
41 switch-disconnector
7 42 13 Manual operation for the mechanism of
62 the earthing function
14 Manual operation for the mechanism of
the load-break function
15 Interlock of the cable compartment cover
16 Arrangement of the cable connections
17 Busbar system
22
18 Switchgear vessel filled with SF6-gas
30
19 Busbar connection
Type ME1 20 Pressure relief device
14 Siemens HA 41.11 · 2003

Design
Panel design (examples)
Circuit-breaker panel Section
21 Compartmentalization for busbar

HA41-2282c eps
22 Earthing busbar with earthing connection

23 Three-position switch-disconnector
24 Spring-operated mechanism
25 Bushing for cable plug with bolted contact (M16)
43 26 Option: Cable T-plug
44 61
27 Cable compartment cover
28 Cable connection compartment
45
46 29 Cable bracket
47 30 Earthing connection for earthing accessories
48 7 46
49 51 31 HV HRC fuse assembly, cover removed
50 52 32 Handle for replacing HV HRC fuse links
11 12 33 Interlock for HV HRC fuse assembly
5 13 34 Cover of the HV HRC fuse compartment
6 63 24
35 Spring-operated / stored-energy mechanism
8 3
15 36 Bushing for cable plug with plug-in contact
9 4
53 25
37 Cable elbow plug with plug-in contact
15
14 38 Switch position indication for load-break function
23 26 “CLOSED – OPEN” and, if applicable,
16 “HV HRC fuse tripped” or “shunt release tripped”
54
10 17 39 Cover for access to the busbar connection and to
27
18 the instrument transformers, screwed on
28
19 40 4MR voltage transformer
29
20 41 4MA7 current transformer
55
21 42 Cover to busbar connection
22 compartment, screwed on
Type LS1 (without voltage transformers) 43 Option: SIPROTEC bay control unit
44 Low-voltage compartment (standard)
HA41-2283c eps
Vacuum circuit-breaker:
45 Opening for the hand crank
– for closing with manual operating mechanism
– for emergency operation with motor operating
mechanism
46 Operating mechanism box
47 Mechanical “ON” pushbutton (not supplied with
61 spring-operated mechanism)
48 Mechanical “OFF” pushbutton
56 49 Operating cycle counter
50 “Spring charged” indicator
57
51 Vacuum interrupter
52 Switch position indication
53 Option: Interlock between vacuum circuit-breaker

and three-position switch-disconnector
54 Option: Three-phase current transformer
(protection transformer)
55 Cable-type current transformer
56 4MT3 plug-in voltage transformer at the busbar
58
57 Bushing for connection of plug-in voltage transformers
58 Plug-in connection according to EN 50 181 /
DIN EN 50 181 as interface type “A”
59
59 Option: 4MT8 plug-in voltage transformer at the connection
60 Deep cable compartment cover
60 61 Wiring duct, removable, for control cables and/or bus wires
62 Screwed-on cover
63 Option: Interlock between three-position
Type LS2-V (with voltage transformers) switch-disconnector and circuit-breaker
Siemens HA 41.11 · 2003 15

Components
3AH vacuum circuit-breakers

Features Operating mechanism
• According to IEC 60 056/ functions
VDE 0670 Parts 101 to 107
(Standards see page 39) Motor operating mechanism 1)
(M1 *) 1 8
• Application of all 8DH10
switchgear in hermetically In the case of the motor oper-
sealed vessel in conformity ating mechanism, the closing 2
spring is charged by means of 10
with the system 3
a motor and latched in the 11
• Climate-independent vacuum 4
charged position (the “spring
interrupter poles in the charged” indication is visible). 5
SF6-filled switchgear vessel Closing is effected either by 6
13
• Maintenance-free for use in- means of an ON pushbutton or 7
doors according to IEC 60 694/ a closing solenoid. The closing
VDE 0670, Part 1000 spring is recharged automati-
cally (for auto-reclosure).
• Individual secondary equipment
15
• A metal bellows is used for Manual operating stored-
gasketless separation of the energy mechanism
SF6-insulation and the operat- The closing spring is charged
ing mechanism – as already by means of the hand crank
used with success for over supplied until latching of the
100,000 vacuum interrupters closing latch is indicated
R-HA41-016 eps
(= “spring charged” indication).

Switching duties and
operating mechanisms Subsequently the vacuum
circuit-breaker can be closed
The switching duties of the either manually or electrically Operating mechanism of the vacuum circuit-breaker
vacuum circuit-breaker are de- (for the legend, see page 17)
and the closing spring can be
pendent, among other factors, on recharged manually. The “possi-
its type of operating mechanism. bility to close” is thus stored
Three operating mechanism once more (for auto-reclosure). Differences between the vacuum circuit-breakers
versions are available: depending on the operating mechanism version
• Motor operating stored-energy Manual spring-operated Operating Motor operating Manual Manual spring-
mechanism mechanism mechanism stored-energy operating operated
– For auto-reclosure (K), (= spring CLOSED, stored-energy version mechanism stored-energy mechanism
– For synchronization and OPEN) mechanism
rapid load transfer (U) The closing spring of the vacuum
Typical uses Utility Classic transfer Simple utility
substations substations and substations
• Manual operating stored- circuit-breaker is charged by and industrial substations (circuit-breaker
energy mechanism means of the hand crank sup- plants without auxiliary employed as
– For auto-reclosure (K) plied until the vacuum circuit- voltage supply transformer
breaker closes. Subsequently switch)
• Manual spring-operated me-
either manual or electrical open- Mechanism Stored-energy Stored-energy Spring
chanism (= spring CLOSED, function CLOSED, CLOSED, CLOSED,
stored-energy OPEN) ing is possible.
stored-energy stored-energy stored-energy
– Not for auto-reclosure (K) Vacuum circuit-breakers with OPEN OPEN OPEN
– For normal closing and spring-operated mechanism are Mechanism With motor 1), With hand With hand
– For storage of one opening not suitable for auto-reclosure. operation manual (emer- crank crank
gency) operat-
Further operating mechanism Trip-free mechanism ion at the panel
features including anti-
The vacuum circuit-breaker pumping
• Located outside the switch- is fitted with a trip-free Closing the Electrically ²) or Mechanically Mechanically
gear vessel in the operating mechanism according to vacuum mechanically at at the panel at the panel
mechanism box and behind IEC 60 056 and VDE 0670. circuit-breaker the panel with with push- with hand
the control board 1) Motor rating at
pushbutton button, option: crank (charging
electrically ²) process)
• Stored-energy spring-operated 24 V to 220 V DC: 350 W
110 V and 220 V AC: 400 VA Closing Always provid- Option Without
mechanism for 10,000 oper- solenoid, e.g. ed, with elec-
ating cycles 2) With closing solenoid for remote trical signal
* Equipment code electrical “closing spring
closing charged”
Abbreviations for switching
duties and applications: CO = CLOSE operation with subsequent Rated O-t-CO O-t-CO O or CO
OPEN operation at the shortest switching or
U = Synchronization and sequence O-t-CO-t’-CO
internal close-open time of the
rapid load transfer
vacuum circuit-breaker Auto- Suitable (multi- Suitable (only –
(make time £ 90 ms)
t = Dead time 0.3 s reclosure (K) ple auto-reclo- with closing
K = Auto-reclosure
sure possible) solenoid)
O = OPEN operation t‘ = Dead time 3 min
For further technical data and description of typical applications,

please refer also to Catalog HG 11.11 “3AH Vacuum Circuit-Breakers”
16 Siemens HA 41.11 · 2003

Components
Secondary equipment of the 3AH vacuum circuit-breaker

The scope of the 3AH vacuum Breaker tripping signal
circuit-breaker secondary equip- (standard)
ment depends on the type of appli- • For electrical signalling (as pulse
cation and offers a wide range of > 10 ms), e.g. to remote control
variations, thus allowing even the 9
systems, in the case of sponta- 1
highest requirements to be satis- neous tripping (e.g. protection)
fied.
• Via limit switch (S6 *) and
Closing solenoid cut-out switch (S7 *) 3
11
• Type 3AY15 10 (Y9 *) Varistor module
• For electrical closing 17
• To limit overvoltages to approx.
500 V for protection devices 13
Shunt releases (when inductive devices are
• Types: mounted in the vacuum circuit-
– Standard: 3AY15 10 (Y1 *) breaker)
– Option: 3AX11 01 (Y2 *), • For auxiliary voltages W 60 V DC
with energy store
• Tripping by protection relay or Auxiliary switch
electrical operation • Type 3SV9 (S1 *)
Current-transformer • Standard: 6NO+6NC, of which
operated release 2NO+2NC+2 changeover
contacts are free 1)
HA41-2296a eps
• Type 3AX11 04 (Y6 *) for trip-

ping pulse W 0.1 Ws in con- • Option: 12NO+12NC, of which
junction with suitable protec- 7NO+4NC+2 changeover
contacts are free 1) Basic equipment with manual spring-operated mechanism
tion systems, e.g. 7SJ4 protec-
tion system, 4MC6.. transformer
protection system, SEG relay Position switch
(other designs on request) • Type 3SE4 (S4 *) 8
1
• Used where no external • For signalling “closing spring
auxiliary voltage is available, charged” 2 10
tripping by protection relay
• Only in conjunction with stored- 3
energy mechanisms 11
Undervoltage release 4
• Type 3AX11 03 (Y7 *) 5 12
Mechanical interlocking
6
• Comprising: • Dependent on the type of 13
– Energy store and unlatching 7
operating mechanism
mechanism
• Option: Switchgear interlocking
– Electromagnetic system, to 14
which voltage is permanently with the three-position switch-
applied in the CLOSED position disconnector (option: closing 15
of the vacuum circuit-breaker; lock-out for the three-position
switch-disconnector in circuit- 16
tripping is initiated when this
voltage drops breaker panels type LS and LT1)
• Option: Operating mechanism
• Connection to voltage trans-
formers possible with mechanical interlocking as
– Spring-operated mechanism:
HA41-2297a eps
Anti-pumping (standard) Hand crank opening is blocked

(mechanical and electrical) – Stored-energy mechanism with
closing solenoid (Y9 *) and
• Function: If CLOSE and OPEN Maximum equipment
pushbutton (S12 *): The push- (with motor operating stored-energy mechanism)
commands are applied simulta- button (S12 *) operated by the
neously and continuously to the mechanical interlock prevents a Secondary equipment (view into the operating mechanism box)
vacuum circuit-breaker, this reverts continuous command to the 1 Gear 11 Circuit-breaker “OPEN”
to its OPEN position subsequent closing solenoid 2 Position switch (S4 *) 12 Option: 2nd release
to closing. The circuit-breaker
• During operation of the three- 3 Closing spring 13 1st release (Y1 *)
remains in this position until a new
CLOSE command is given. Thus position switch-disconnector 4 Motor (M1 *) 14 Option: Mechanical inter-
continuous closing and opening from CLOSED to OPEN: locking with interrogation
5 Operating cycle counter
(= pumping) is avoided. vacuum circuit-breaker of the three-position
cannot be closed. 6 “Closing spring charged” indicator switch-disconnector
7 Closing solenoid (Y9 *) 15 Operating rod to contact
1) For utilization * Equipment Abbreviations: pressure springs
8 Option: Auxiliary switch
by the code NO = normally-open contact
12NO+12NC 16 Interlocking to the three-
customer NC = normally-closed contact
position switch-disconnector
9 Auxiliary switch
For further technical data and description of typical applications, 6NO+6NC (S1 *) 17 Actuation for closing the
please refer also to Catalog HG 11.11 “3AH Vacuum Circuit-Breakers” vacuum circuit-breaker
10 Circuit-breaker “CLOSED”
Siemens HA 41.11 · 2003 17

Components
Three-position switch-disconnectors
Features
• Switch positions: CLOSED –
OPEN – EARTHED
• Switching functions as
general-purpose switch-
R-HA41-012 eps
disconnector (class E3)
according to
– IEC 60 265-1
– VDE 0670 Part 301
– IEC 62 271-102
– VDE 0670 Part 2/EN 60 129
(Standards see page 39)
• Designed as a multi-chamber
switch incorporating the
functions
– Switch-disconnector and
– Make-proof earthing switch
• Operation via a gas-tight
welded bushing at the front
of the switchgear vessel
Three-position switch-disconnector
EARTHED
HA41-2288a eps
OPEN
SF6-insulation
1 2 3 4 5 6 CLOSED
Detachable lever mechanism

with three-position switch-disconnector
Switch positions
1 Three-position switch-disconnector
2 Gear plate
3 Switchgear vessel
4 Operating mechanism rocker
5 Detachable lever mechanism
6 Operating lever inserted
For further details, please refer to

Catalog HA 40.1 “Switchgear
Type 8DJ and 8DH for Secondary
Distribution Systems up to 24 kV,
SF6-Insulated” (General Part)
18 Siemens HA 41.11 · 2003

Components
Busbars
Features
• Safe-to-touch as a result of
use of metal covers
R-HA41-017a eps
• Plug-in type
• Consisting of round-bar
copper, insulated by means
of silicone rubber
• Busbar joints with cross and
end adapters, insulated by 2 8
means of silicone rubber
• Insensitive to pollution and 3
condensation
• Switchgear extension or
panel replacement is possi- 7
ble without SF6-gas work
• Special busbar connections
to metering panels type ME1
are possible. Connection to
the
– Cable connection bushings
of the adjacent panel Busbar compartments over 2 panels
with busbar connections, busbar covers removed
or to the
– Busbar bushings
• Busbar arrangement in panel
blocks within the switchgear 7
vessel filled with SF6-gas
HA41-2289b eps
8
• Option: Screened busbar:
– Field control by means of 9
electrically conductive layers
on the silicone-rubber
insulation (both internally 1 10
and externally); 2
– Installation of 4MC70 32
current transformers is thus 3
possible 4
• Option: Capacitive voltage 5
detection system for the
busbar, refer also to the
Top view
product range, pages 8 6
to 13
Insulated plug-in type busbar

unscreened design
Busbar system
1 End adapter
2 Cross adapter
3 Busbar insulation of silicone rubber
4 Threaded bolt M12 / M16
5 Busbar, Cu, diameter 32 mm
6 Stopper
Switchgear vessel
7 Primary enclosure panel 1
8 Primary enclosure panel 2
9 Bushing
10 Capacitive tap at the bushings,
earthed (standard)
Siemens HA 41.11 · 2003 19

Components
4MT3 * and 4MT8 * plug-in voltage transformers for panel types LS, TR, SE and ME3
Panel section
type LS2-V
HA41-2290b eps
R-HA41-019 eps
R-HA41-018a eps
4MT3 plug-in
voltage
1
transformer
(for the busbar)
R-HA41-020 eps
4MT8 plug-in
voltage
transformer
(at the cable
1 4MT3 * for the busbar 4MT8 plug-in voltage transformer connection)
2 4MT8 * at the cable connection mounted on cable T-plug (in panel type LS1-V)
Features Technical data

• According to IEC 60 044-2/ 4MT3 * and 4MT8 * voltage transformers
VDE 0414 Part 2 Primary data Secondary data for 4MT3 voltage transformers
• Designed as single-pole volt- Max. equipment operating 12 kV Rated voltage 100/ 3 V
age transformers, plug in type voltage Um (= 1.2 x UN) 110/ 3 V
• Metal-enclosed, safe-to-touch Rated voltage UN at max. 3.3/ 3 kV at 10 kV Rated voltage for 100/3 V
rated short-duration 3.6/ 3 kV at 10 kV auxiliary winding 110/3 V
• Connection system with power-frequency (option)
4.8/ 3 kV at 20 kV
plug-in contact and withstand voltage
5.0/ 3 kV at 20 kV Rated thermal 8A
– Inside cone for 4MT3 6.0/ 3 kV at 20 kV limit current
voltage transformers 6.6/ 3 kV at 20 kV (measuring winding)
– Outside cone for 4MT8 7.2/ 3 kV at 20 kV
Rated long-time thermal 5A
voltage transformers 10.0/ 3 kV at 28 kV current (8 h)
• Inductive type 11.0/ 3 kV at 28 kV
Rated lightning impulse 75 kV Rating VA 25 15 60 100 150
• Climate-independent withstand voltage
Class 0.2 0.5 0.5 1 1
• Secondary connection by Rated voltage factor (8 h) 1.9 x UN
means of plugs inside the panel Secondary data for 4MT8 voltage transformers
Max. equipment operating 24 kV Rated voltage 100/ 3 V
Installation voltage Um (= 1.2 x UN) 110/ 3 V
• Arrangement on the switch- Rated voltage UN at max. 13.8/ 3 kV at 38 kV Rated voltage for 100/3 V
gear vessel for busbar rated short-duration 15.0/ 3 kV at 38 kV auxiliary winding 110/3 V
metering: power-frequency (option)
17.5/ 3 kV at 50 kV
– 4MT3 voltage transformer withstand voltage
22.0/ 3 kV at 50 kV Rated thermal 4A
for panel types LS2, SE2, Rated lightning impulse 125 kV
limit current
ME3 and LT1-V (measuring winding)
withstand voltage
• Arrangement at the cable Rated voltage factor (8 h) 1.9 x UN
Rated long-time thermal 3A
connection: current (8 h)
– 4MT8 plug-in voltage trans-
Rating VA 15 15 30 30 100
former, on shielded cable
T-plug, for panel types LS1-V, Class 0.2 0.5 0.5 1 3
LS2-V and TR-V (deep cable Combination of 4MT8 * voltage transformers with cable T-plugs (screened, without metal housing)
compartment cover required)
Make Type Combination Make Type Combination
– 4MT8 voltage transformer,
which is directly plugged in the Euromold (K) 400 TB, (K) 400 TBS, yes ABB Energiekabel SEHDT (13/23) yes
(K) 440 TB, AGT 10/20 ABB Energiekabel SET (12/24) on request
bushing via an adapter with a
plug-in contact (interface type nkt cables CB 24-630, ASTS 10/630, yes Cooper DT 400 P yes
ASTS 20/630
“A”), for panel type TR-V (deep Raychem RSTI on request
cable compartment cover Pirelli Elektrik FMCTs-400, FMCTg-400 yes
required) * Disassembly is necessary in order to perform local switchgear voltage tests
20 Siemens HA 41.11 · 2003

Components
4MC63 three-phase current transformers for panel type LS

Panel section
type LS1
R-HA41-021b eps
HA41-2291b eps
R-HA41-022 eps
4MC63 three-phase
current transformer
1 4MC63 three-phase 4MC63 three-phase current transformer
current transformer on the bushings of the cable connection

• According to IEC 60 044-1/ 4MC63 10 three-phase current transformer 4MC63 11 three-phase current transformer
for IN £ 150 A and ID = 630 A for IN £ 400 A and ID = 630 A
VDE 0414 Part 1
• Designed as three-pole Primary data Primary data
ring-core current transformers Max. equipment operating 0.72 kV Max. equipment operating 0.72 kV
voltage Um voltage Um
• Free of dielectrically
stressed cast-resin parts Rated current IN A 150 100 75 50 Rated current IN A 400 300 200
(due to design) Rated short-duration 3 kV Rated short-duration 3 kV
power- frequency with- power-frequency with-
• Insulation class E stand voltage (winding test) stand voltage (winding test)
• Inductive type Rated thermal short-time 25 kA Rated thermal short-time 25 kA
withstand current Ith withstand current Ith
• Climate-independent
• Secondary connection by Rated continuous 630 A Rated continuous 630 A
means of a terminal strip thermal current ID thermal current ID
inside the panel
Transient overload 1.5 x ID / 1 h Transient overload 2 x ID / 0.5 h
Installation current current
• Arranged outside the switch- Rated peak withstand unlimited Rated peak withstand unlimited
gear vessel on the bushings current Idyn current Idyn
of the cable connection Secondary data Secondary data
• Mounted at the factory Rated current A 1 0.67 0.5 0.33 Rated current A 1 0.75 0.5
Rating VA 2.5 1.7 1.25 0.8 Rating VA 4 3 2
Other designs
(option) Rated current (option) 5A Rated current (option) 5A
Current at ID 4.2 A Current at ID 1.575 A
Three-phase current trans-
formers for protection equip- Protec- Class 10 P Protec- Class 10 P
tion tion
ment based on the current- core
Overcurrent factor 10
core
Overcurrent factor 10
transformer operation principle:
• 7SJ4 protection system
as definite-time overcurrent
protection
• Definite-time overcurrent
protection relay make SEG,
type WIP 1
Other values on request Other values on request
Siemens HA 41.11 · 2003 21

Components
4MC70 33 and 4MC70 31 cable-type current transformers for panel types LS, RK and TR
Front Panel section

view type LS1
R-HA41-025 eps
R-HA41-023a eps
HA41-2292b eps
H
4MC70 31 cable-type
current transformer
R-HA41-024 eps
H
4MC70 33 cable-type
current transformers,
4 different overall heights
2 2
1 1
*
4MC70 33 cable-type current transformer

for the cables at the panel connection
1 Cable-type current transformer
2 Cable shield

• According to IEC 60 044-1/ 4MC70 33 cable-type current transformer 4MC70 31 cable-type current transformer
VDE 0414 Part 1 Primary data Primary data
• Designed as single-pole ring- Max. equipment operating 0.72 kV Max. equipment operating 0.72 kV
core current transformers voltage Um voltage Um
• Free of dielectrically stressed Rated current IN 30 A to 600 A Rated current IN 50 A to 600 A
cast-resin parts (due to design) Rated short-duration 3 kV Rated short-duration 3 kV
power-frequency with- power-frequency with-
• Insulation class E
stand voltage (winding test) stand voltage (winding test)
• Inductive type Rated thermal short-time 25 kA Rated thermal short-time 25 kA
• Climate-independent withstand current Ith withstand current Ith
• Secondary connection by
Rated continuous max. 1.2 x IN Rated continuous max. 1.2 x IN
means of a terminal strip thermal current ID thermal current ID
inside the panel
• Only for shielded cables Transient overload 1.5 x ID / 1 h or Transient overload 1.5 x ID / 1 h or
current 2 x ID / 0.5 h current 2 x ID / 0.5 h
Installation Rated peak withstand unlimited Rated peak withstand unlimited
current Idyn current Idyn
• 4MC70 33 cable-type current
transformer for panel type LS Secondary data Secondary data
• 4MC70 31 cable-type current Rated current 1 A (option: 5 A) Rated current 1 A (option: 5 A)
transformer for panel types Meas- Class 0.2 0.5 1 Meas- Class 1
RK and TR uring Overcurrent factor FS10 (option: FS5) uring Overcurrent factor FS5 (option: FS10)
core core
• Arranged outside the switch- Rating 2.5 VA to 10 VA Rating 2.5 VA to 10 VA
gear vessel around the cable Pro- Class 10 P 5P Option: Secondary tap 1:2
at the panel connection tection Overcurrent factor 10 10
core
• Transformers mounted on a Rating 2.5 VA to 10 VA
supporting plate at the fac-
Option: Secondary tap 1:2
tory; final assembly around (e.g. 150 A – 300 A)
the cables on site
Dimensions Dimensions
• For double cable: 300 mm
deeper cable compartment Overall height H, mm 50 100 170 285 Overall height H 89 mm
dependent on the
cover core data
* Max. 230 mm, depending on Outside diameter 145 mm Width x Depth 85 mm x 114 mm
the core data of the 4MC70 33 Inside diameter 55 mm Inside diameter 40 mm
cable-type current transformer,
overall heights 170 and 285 mm For cable diameter 50 mm For cable diameter 36 mm
(observe floor openings on page 34)
22 Siemens HA 41.11 · 2003

Components
4MC70 32 bus-type current transformers for panel type LT (for screened busbars only)
Panel section
type LT1
HA41-2293b eps
R-HA41-026a eps
R-HA41-027 eps
1
4MC70 32 bus-type
1 4MC70 32 bus-type current transformer
current transformer 4MC70 32 bus-type current transformer,
mounted on screened busbars, in some cases
between the panels

• Used exclusively for 4MC70 32 bus-type current transformer
screened busbars Primary data
• Preferably in combination Max. equipment operating 0.72 kV
with panel type ME2 voltage Um
• According to IEC 60 044-1/ Rated current IN 200 A to 600 A
VDE 0414 Part 1 Rated short-duration 3 kV
power-frequency with-
• Designed as single-pole
stand voltage (winding test)
ring-core current trans-
formers Rated thermal short-time 25 kA
withstand current Ith
• Free of dielectrically
stressed cast-resin parts Rated continuous max. 1.2 x IN
(due to design) thermal current ID
• Insulation class E
Transient overload 1.5 x ID / 1 h or
• Inductive type current 2 x ID / 0.5 h
• Climate-independent Rated peak withstand unlimited
current Idyn
• Secondary connection by
means of a terminal strip Secondary data
inside the panel Rated current 1 A (option: 5 A)
Meas- Class 0.2 0.5 1
Installation uring Overcurrent factor FS10 (option: FS5)
• Arranged outside the core
Rating 2.5 VA to 10 VA
switchgear vessel only on
the screened busbars Pro- Class 10 P 5P*
tection Overcurrent factor 10 10
• Installation of the bus-type core
current transformers either Rating 2.5 VA to 15 VA
between the panels or alter- Option: Secondary tap 1:2
natively (e.g. 150 A – 300 A)
• Supplied loosely (including Dimensions

the busbar connections), if Overall width B, 80 mm 150 mm
the mounting position of the dependent on the
bus-type current transform- core data
ers lies at the joint of a trans- Outside diameter 125 mm
port unit Inside diameter 55 mm
Other values on request * On request
Siemens HA 41.11 · 2003 23

Components
4MA7 current transformers and 4MR voltage transformers
for air-insulated billing metering panels type ME1
R-HA41-028 eps
R-HA41-029a eps
Panel section type ME1
HA41-2294c eps
4MR14 voltage
1 transformer
R-HA41-030a eps
2
4MA7 current
transformer
1 4MR voltage transformer 4MR voltage transformers and
2 4MA7 current transformer 4MA7 current transformers installed in
billing metering panel type ME1

4MA7 single-pole current transformer 4MR single-pole voltage transformer
4MA7 current transformer
Primary data Primary data
• According to IEC 60 044-1/
VDE 0414 Part 1 Max. equipment operating 12 kV 24 kV Max. equipment operating 12 kV
voltage Um voltage Um (= 1.2 x UN)
• Dimensions according to Rated short-duration 38 kV 50 kV Rated voltage UN at max. 3.3/ 3 kV at 10 kV
DIN 42 600, Part 8 (small power-frequency rated short-duration 3.6/ 3 kV at 10 kV
design) withstand voltage power-frequency
4.8/ 3 kV at 20 kV
withstand voltage
• Designed as single-pole Rated lightning impulse 95 kV 125 kV 5.0/ 3 kV at 20 kV
indoor block-type current withstand voltage 6.0/ 3 kV at 20 kV
6.6/ 3 kV at 20 kV
transformers Rated current IN 25 A to 600 A
7.2/ 3 kV at 20 kV
• Cast-resin insulated Rated thermal short-time up to 25 kA
10.0/ 3 kV at 28 kV
withstand current Ith
• Insulation class E 11.0/ 3 kV at 28 kV
Rated lightning impulse 75 kV
• Secondary connection by Rated continuous up to 1.2 x IN
withstand voltage
means of screw-type thermal current ID
Rated voltage 1.9 x UN
terminals factor (8 h)
Rated peak withstand max. 2.5 x Ith
4MR voltage transformer current Idyn Max. equipment operating 24 kV
voltage Um (= 1.2 x UN)
• According to IEC 60 044-2/ Secondary data
Rated voltage UN at max. 13.8/ 3 kV at 38 kV
VDE 0414 Part 2 Rated current 1 A or 5 A rated short-duration 15.0/ 3 kV at 38 kV
• Dimensions according to Meas- Class 0.2 0.5 1 power-frequency
17.5/ 3 kV at 50 kV
DIN 42 600, Part 9 (small uring withstand voltage
Overcurrent factor FS5 or FS10 20.0/ 3 kV at 50 kV
design) core 22.0/ 3 kV at 50 kV
Rating 10 VA to 15 VA
• Designed as indoor Pro- Class 5 P or 10 P Rated lightning impulse 125 kV
withstand voltage
voltage transformers: tection Overcurrent factor 10
– Type 4MR, single-pole core Rated voltage 1.9 x UN
Rating 5 VA or 15 VA factor (8 h)
– Option: Type 4MR, two-pole
• Cast-resin insulated Secondary data
• Insulation class E Rated voltage 100/ 3 V
110/ 3 V
• Secondary connection by 120/ 3 V
means of screw-type Rated voltage for auxiliary 100/3 V
terminals winding (option) 110/3 V
120/3 V
Rating 20 VA 50 VA 100 VA
Class 0.2 0.5 1
24 Siemens HA 41.11 · 2003

Components
4MK * metal-enclosed combined transformers
for billing metering panels type ME2
R-HA41-032 eps
R-HA41-031a eps
1
1 4MK3
Panel section type ME2 combined
voltage
HA41-2295b eps
transformer
2 4MK1
combined
1 current
transformer
2
4MK combined
transformer
1 4MK3 combined voltage 4MK combined transformers installed in
transformer billing metering panel type ME2
2 4MK1 combined current
transformer
Technical data
4MK1 combined current transformer 4MK3 combined voltage transformer
Features
Primary data Primary data
• 4MK * combined
Max. equipment operating 12 kV 24 kV Max. equipment operating 12 kV
transformer, comprising voltage Um voltage Um (= 1.2 x UN)
– 4MK1 combined current
transformer Rated short-duration 28 kV 50 kV Rated voltage UN at max. 3.3/ 3 kV at 10 kV
power-frequency rated short-duration 3.6/ 3 kV at 10 kV
– 4MK3 combined voltage withstand voltage power-frequency
transformer 4.8/ 3 kV at 20 kV
withstand voltage
Rated lightning impulse 75 kV 125 kV 5.0/ 3 kV at 20 kV
• According to IEC 60 044-3/ withstand voltage 6.0/ 3 kV at 20 kV
VDE 0414 Part 5 6.6/ 3 kV at 20 kV
Rated current IN 50 A to 600 A
7.2/ 3 kV at 20 kV
• Designed as single-pole, Rated thermal short-time up to 25 kA
10.0/ 3 kV at 28 kV
combined indoor trans- withstand current Ith
11.0/ 3 kV at 28 kV
formers
Rated lightning impulse 75 kV
Rated continuous up to 1.2 x IN
• Metal-enclosed withstand voltage
thermal current ID
• Insulation class E Rated voltage 1.9 x UN
factor (8 h)
• Inductive type Rated peak withstand max. 2.5 x Ith
current Idyn Max. equipment operating 24 kV
• Secondary connection by voltage Um (= 1.2 x UN)
means of screw-type Secondary data
Rated voltage UN at max. 13.8/ 3 kV at 38 kV
terminals Rated current 1 A or 5 A rated short-duration 15.0/ 3 kV at 38 kV
Meas- Class 0.2 0.5 1 power-frequency
17.5/ 3 kV at 50 kV
Panel type ME2 uring Overcurrent factor FS5 or FS10
withstand voltage
20.0/ 3 kV at 50 kV
core 22.0/ 3 kV at 50 kV
• For combination with Rating 10 VA to 15 VA
left-hand panels Pro- Class 10 P Rated lightning impulse 125 kV
– As individual panels or tection Overcurrent factor 10 withstand voltage
– As panel blocks (on request) core Rated voltage 1.9 x UN
Rating 5 VA or 15 VA factor (8 h)
• For combination with
Secondary multi-ratio option
right-hand panels as end function Secondary data
panels or panel blocks
Rated voltage 100/ 3 V
110/ 3 V
Rated voltage for auxiliary 100/3 V
winding (option) 110/3 V
Rating 30 VA 75 VA 150 VA
Class 0.2 0.5 1
* Available only as a combination of

current and voltage transformers
Siemens HA 41.11 · 2003 25

Components
Cable connection
Features
Cable connection · Examples
• Bushings with outside cone
• Uniform cable connection L1 L2 L3 L1 L2 L3
Cable connections in
height 575 mm ring-main panels
• With cable bracket, e.g. 1 Prepared for cable
type C40 according to plugs with bolted
contact (M16)
DIN EN 50 024 1 2
3 2 Phase L1:
• Access to the cable con- Make: Euromold,
nection compartment only if 4 type K400 LB as
the feeder has been isolated cable elbow plug
and earthed 3 Phase L2:
Make: Euromold,
Special features type K400 TB as
cable T-plug
– In ring-main panels
4 Phase L3:
– In circuit-breaker panels
R-HA41-034 eps
R-HA41-033 eps
Make: Euromold,
– In cable panels: type AGT 20/630 as
• With bolted contact (M16) cable T-plug
as interface type “C” Cable connection compartment, Cable plugs with For options A, B, C
according to EN 50181/ supplied without cable clamps bolted contact (M16) and E, see below
DIN EN 50181
• For thermoplastic- L1 L2 L3 L1 L2 L3 Cable connections in
insulated cables circuit-breaker panels
• For paper-insulated 5 Prepared for cable
mass-impregnated cables plugs with bolted
with adapter systems contact (M16)
5 6
• For conventional cable 6 Phase L1:
7
Elbow adapter,
sealing ends via elbow make: Siemens,
8
adapter AKE 20/630 type AKE 20/630
(make Siemens)
7 Phase L2:
• For cable T-plugs or cable Make: Euromold,
elbow plugs with bolted type K400 TB as
cable T-plug
contact
8 Phase L3:
• For connection cross-
R-HA41-035 eps
R-HA41-036 eps
Make: Euromold,
sections up to 300 mm² type AGT 20/630 as
(standard) cable T-plug
• Cable routing downwards, Cable connection compartment, Cable plugs with For options A, B, C,
cable connection at front supplied without cable clamps bolted contact (M16) E and F, see below
• For rated normal currents of

400/630 A L1 L2 L3 L1 L2 L3
Cable connections in
– In transformer panels: transformer panels
• With plug-in contact as 9 Prepared for cable
interface type “A” 10 elbow plugs with plug-in
according to EN 50 181/ 9 contact
11
DIN EN 50 181 10 Phase L1:
12 Make: Euromold,
• For cable elbow plugs
type AWGL
with plug-in contact
11 Phase L2:
• For thermoplastic- Make: Euromold,
insulated cables type K158 LR
• For connection cross- 12 Phase L3:
sections up to 120 mm² Make: Euromold,
R-HA41-037 eps
R-HA41-038 eps
type AWG 20/250

• For rated normal currents (with metal housing)
of 200 A For options A, D and F,
Cable connection compartment, Cable elbow plugs with see below
Options supplied without cable clamps plug-in contact
See figures on the right
Options D Bushings as interface type “C” according to
EN 50 181 / DIN EN 50 181 for cable plugs with bolted contact (M16)
A Mounted cable clamps
E Suitable for connection of plug-in surge arresters in conjunction with
B Short-circuit / earth-fault indicator
corresponding cable T-plugs
* Cable plugs, cable sealing ends C Double cable connection with
F Suitable for connection of 4MT8 metal-enclosed voltage
and cable clamps are not corresponding cable plugs and
transformers in conjunction with corresponding cable T-plugs;
included in the scope of supply deep cable compartment cover
deep cable compartment cover is required
26 Siemens HA 41.11 · 2003

Components
Low-voltage equipment
• Height
– Standard 600 mm
– Option 900 mm
• Safe-to-touch
compartmentalization from 1
the high-voltage part of the
panel
2 3
• Installation on the panel:
– Standard for circuit-breaker
panels type LS and bus
sectionalizer panel type LT1
– Option for all other panel 4
types, depending on the
R-HA41-041a eps
R-HA41-039a eps
scope of the secondary

equipment
• For accommodation of protec-
Low-voltage compartment Electronic control board with
tion, control, measuring and of a circuit-breaker panel multifunction protection relay
metering equipment, e. g. type LS SIPROTEC 4 7SJ63
suitable for multifunction
protection relay SIPROTEC 4
R-HA41-040 eps
7SJ63 1 LEDs
• Electronic control board 2 LCD

of the multifunction protec- 3 Navigation keys
tion relay SIPROTEC 4 7SJ63 4 Function keys
with the following features:
1 User-programmable LEDs
with application-specific label,
for displaying any desired
process and equipment data
2 LCD for process and
equipment data, e.g. for
– Measuring and metering
values
– Binary information on status Open low-voltage compartment
of switchgear and switching with (optional) equipment
device
– Protection data
– General indications
– Alarms
3 Keys for navigation in the Low-voltage niche
menus and for entering values
4 Four user-programmable
1 Low-voltage
function keys for frequently niche
performed actions
2 Equipment
1 (option)
Low-voltage niche
• Only inside billing metering 2
panels type ME1
• Option: For accommodation,
e.g. of voltage transformer
mcbs
Low-voltage cables
• Control cables of the panel to
the low-voltage compartment
R-HA41-042 eps
are connected via multi-pole,

coded module plug connec-
tors
• Option: Plug-in bus wires from Low-voltage niche of a
billing metering panel type ME1
panel to panel are routed in with open cover
the separate wiring duct on
the panel
Siemens HA 41.11 · 2003 27

Dimensions
aa
28
2000 (2300)*
2000 (2300)*
2000 (2300)*
350
350
Cable panel
type K
500
1400
Ring-main panel
type RK
1400
Transformer panel
type TR
1
3
1400
Siemens HA 41.11 · 2003

HA41-2298d eps
³15
HA41-2299d eps
³15
HA41-2300c eps
³15
aa
Ring-main, cable, transformer and circuit-breaker panels as individual panels
215 110 110

215 110 110
215 110 110
600 (900)*
312
312
553
515
~560**
600 (900)*
312
553
~560**
600 (900)*
~520**
747
775
747
775
747
775
60
40
60
40
60
~565
40
575
575
2000 (2300****)
2000 (2300****)
500
500
1400
type LS1
1400
type LS2
Cable panel type K:

1 Option: Earthing function
HA41-2301b eps
³15
HA41-2302b eps
³15
2 Interlocking of the cable compartment cover

in conjunction with earthing function
312
215 110 110
312
215 110 110
3 Cable compartment cover screwed on (without earthing function)
* Option:
With low-voltage compartment
** Dependent on the type of
cable plug
*** Available mounting depth
for low-voltage equipment
**** Option: With high
low-voltage compartment 900 mm
600 (900****)
553
~560**
600 (900****)
553
~560**
747
775
747
775
426***
426***
~565
40
~565
40
Dimensions
Ring-main, cable and transformer panels in panel blocks
HA41-2304b eps
HA41-2303b eps
HA41-2305b eps
2000 (2300)*
2000 (2300)*
2000 (2300)*
1400
1400
1400
RK RK RK RK RK TR TR
700 1050 1000

Ring-main Ring-main Transformer
panel block type R-B2 panel block type R-B3 panel block type T-B2
HA41-2306b eps
HA41-2307b eps
HA41-2308b eps
2000 (2300)*
2000 (2300)*
2000 (2300)*
1400
1400
1400
TR TR TR RK TR RK RK TR
1500 700 1050

Transformer Ring-main/transformer Ring-main/transformer
panel block type T-B3 panel block type RT-B2 panel block type 2RT-B3
HA41-2309b eps
HA41-2310b eps
2000 (2300)*
2000 (2300)*
1
Cable panel type K:
2 1 Option: Earthing function
1400
1400
2 Interlocking of the cable compartment cover

3 in conjunction with earthing function
3 Cable compartment cover screwed on
(without earthing function)
RK RK RK TR K TR
* Option:
1400 700
Ring-main/transformer Cable connection/transformer
panel block type 3RT-B4 panel block type KT-B2
Siemens HA 41.11 · 2003 29

Dimensions
2000 (2300****)
aa
2000 (2300****)
2000 (2300)*
30
500
Bus sectionalizer
panel type LT1
500
500
1400
1400
Bus sectionalizer
panel type LT1-V
1400
Bus sectionalizer
panel type LT2
Siemens HA 41.11 · 2003

1
1
HA41-2311b eps
³15
HA41-2312b eps
³15
HA41-2313c eps
³15
aa
Bus sectionalizer panels and voltage metering panel as individual panels
312
215 110 110
312
215 110 110
215 110 110
600 (900****)
600 (900****)
600 (900)*
312
747
775
747
775
747
775
426***
426***
40
40
60
40
2000 (2300)*
500
Voltage metering
panel type ME3
1400
1
1 Cable compartment cover

screwed on
* Option: With low-voltage compartment

*** Available mounting depth for
low-voltage equipment
**** Option: With high
HA41-2315c eps
³15
low-voltage compartment 900 mm

215 110 110
600 (900)*
312
747
775
60
40
Busbar earthing panels
as individual panels
a 2000 (2300)*
2000 (2300)*
350
Earthing
500
Earthing
1400
panel type SE1
panel type SE2
* Option:
1400
HA41-2316c eps
³15
HA41-2317c eps
³15
With Low-voltage compartment

aa
215 110 110
215 110 110
600 (900)*
312
600 (900)*
312
747
775
747
775
60
40
60
40
2000 (2300)*
Only individual
panel or panel block 1)
on the left
HA41-2477 eps
Connection
at the busbar
* Option:
Billing metering panel ME2 as individual panel and

metering panel combin. with billing metering panel
600
Billing metering
panel type ME2
1400
Metering panel combination
1
Billing metering
panel
type ME2
600
HA41-2323d eps
³15
Billing metering panel type ME2 with

individual panel attached on the left
and panel block attached on the right
(example)
1 Cover screwed on

*** Available mounting depth
for low-voltage equipment
1) Panel block on request
Dimensions
600 (900)*
312
Individual panel
or panel block
on the right
Connection
at the busbar
747
775
339***
215 110 110
Siemens HA 41.11 · 2003

60
40
1400
31
Dimensions
Billing metering panels type ME1... as individual panels
aa
32
2000 (2300)*
255
850
Billing metering
panel type ME1
1 Cover screwed on
* Option:
255
1400

1
HA41-2319d eps
³15
a
** Dimension for cable routing: 323 mm for combination of

panel type ME1-K with pressure absorber duct
Siemens HA 41.11 · 2003

312
215 110 110
600 (900)*
747
775
60
675
40
1135
2000 (2300)*
2000 (2300)*
2000 (2300)*
255
255
255
850
Billing metering
panel type ME1-K
850
Billing metering
panel type ME1-S
850
Billing metering
panel type ME1-KS
255
255
255
1400
1400
1400
1
HA41-2320d eps
³15
1
HA41-2321d eps
³15
1
HA41-2322e eps
³15
312
215 110 110
312
600 (900)*
~145**
600 (900)*
600 (900)*
215 110 110
~600
747
775
747
775
747
775
60
675
40
60
675
40
60
675
40
1135
1135
1135
Dimensions
Metering panel combinations with billing metering panels type ME1...

Possible panel arrangements
Billing metering panels with individual panels
The following types of individual panels
or panel blocks attached on the left and right (examples)
or panel blocks can be attached to billing
metering panels – on the right or left:
Possiblity 1
Individual panel Billing metering Individual panel
or panel block, panel or panel block, Possibility 1
on the left type ME1 on the right
• Types attached on the left
with connection at the feeder
– Individual panel type
RK-U, K-U, TR-U, LS1-U or LS2-U
– Panel block type
R-B2 or R-B3 (in RK-U panel),
T-B2 or T-B3 (in TR-U panel),
RT-B2, 2RT-B3 or 3RT-B4 (in TR-U panel)
1400
or KT-B2 (in TR-U panel)
• Types attached on the right
with connection at the busbar
HA41-2441a eps

RK, K, TR, LS1, LS2, SE1, SE2, ME3 or LT
850 R-B2, R-B3, T-B2, T-B3, RT-B2, 2RT-B3, 3RT-B4
Connection Connection or KT-B2
at the feeder * at the busbar
Possibility 2
Possiblity 2 with connection at the busbar
Only Billing metering Individual panel – Individual panel type
individual panel, panel or panel block, RK, K, TR, LS1, LS2, SE1, SE2, ME3 or LT
on the left type ME1 on the right
– Panel blocks cannot be attached
• Types attached on the right
with connection at the feeder
RK-U, K-U, TR-U, LS1-U or LS2-U
R-B2 or R-B3 (in RK-U panel),
1400
T-B2 or T-B3 (in TR-U panel),

RT-B2, 2RT-B3 or 3RT-B4 (in RK-U panel)
or KT-B2 (in K-U panel)
HA41-2442a eps
Possibility 3
850 – Individual panel type
Connection Connection
at the busbar at the feeder ** RK, K, TR, LS1, LS2, SE1, SE2, ME3 or LT
– Panel blocks cannot be attached
Possiblity 3 • Types attached on the right
Only Billing metering Individual panel
individual panel, panel or panel block, RK, K, TR, LS1, LS2, SE1, SE2, ME3 or LT
on the left type ME1-S on the right – Panel block type
R-B2, R-B3, T-B2, T-B3, RT-B2, 2RT-B3, 3RT-B4
or KT-B2
1400
HA41-2443a eps
Connection inside the panel block:

* Only possible in the right-hand feeder
850
Connection Connection ** Only possible in the left-hand feeder
at the busbar at the busbar
Siemens HA 41.11 · 2003 33

³15
1
aa
³15
1
³15
34
Dimensions
480
150480
150
HA41-2325d eps
HA41-2326d eps
³15 480
150
HA41-2327c eps
HA41-2328c eps
31
233 122 69
47 197
31
233 122 69
47 197
31
233 122 69
47 197
31
233 122 69
47 197
35
10
19
40
35
10
19
40
35
10
19
40
15
35
19
40
a
a
a
Floor openings (dimensions in red) and fixing points
Standard (for special versions, see pages 36 and 37)
175
350
110 110
106 100
270
150 150
106 125 125
250
131
420
55
623
For individual panels
500
150 150
106 125 125

420
470
600
300
520
Siemens HA 41.11 · 2003

14 x 28
713
610
28 x 14
250
500
55
623
55
63
623
14 x 28
713
610
28 x 14
14 x 28
713
425
28 x 14
55
623
4
2
4
63
63
50 135
14 x 28
713
610
28 x 14
4
2
4
2
4
5
63
4
2
4
• For ring-main panels
type RK
• For cable panels
type K
• For busbar earthing
panel
type SE1
• For circuit-breaker
panel types LS1 and LS2
each without cable-type
current transformer
• For transformer
panels type TR
• For bus sectionalizer
panels type LT
• For busbar earthing
panel type SE2
• For busbar voltage
metering panel type ME3
• For circuit-breaker
panel types LS1 and LS2
each with cable-type
current transformers
• For billing metering

panels
type ME2
³15
1
³15
1
³15
1
HA41-2329c eps
480
150
HA41-2330d eps
480
150
HA41-2331d eps
31
233 122 69
47 197
31
233 122 69
47 197
31
233 122 69
47 197
35
19
40
35
10
19
40
35
10
19
40
275
256
175
110 110
106 100
40
350
150 150
106 125 125
1 Wall distance
500
255
For panel block

350
620
For panel blocks
250
40
850
300
770
700
40
350
19
312
1000
500
920
255
110 110
500
19
40
150 150
55
623
462
55
623
713
610
28 x 14
14 x 28
713
610
2 Fixing frame (base) of an individual panel or panel block

3 Floor opening for high-voltage cables and, if applicable,
control cables
4 Fixing points
55
63
28 x 14
14 x 28
63
623
4
2
14 x 28
713
28 x 14
5 For 4MC70 33 cable-type current transformer with outside diameter

145 mm for arrangement beneath the panel
6 Position of the incoming cables for metering panels type ME1...
7 Position of the incoming cables for the feeder
B Cutout in the mounting frame for extended floor opening for

panel with cable-type current transformers
4
2
63
610
4
2
4
• For billing metering
–
–
–
–
panels
Type ME1
Type ME1-K
Type ME1-S
Type ME1-KS
• For ring-main
panel block
type R-B2
• For ring-main/
transformer
panel block
type RT-B2
• For cable connection/
transformer
panel block
type KT-B2
• For transformer
panel block
type T-B2
aa
³15
1
³15
1
³15
1
480
150
HA41-2332d eps
480
150480
150
HA41-2333d eps
HA41-2334d eps
31
233 122 69
47 197
31
233 122 69
47 197
31
233 122 69
47 197
35
10
19
40
35
10
19
40
35
10
19
40
a
175
106 100
40
110 110
350
110 110
106 100
350
350
For panel blocks
175
40
For panel block
250
150 150
106 125 125
500
For panel block
1 Wall distance
4 Fixing points
350
40
1050
40 40
350
110 110
19
350
970
40 40
350
110 110
19
500
350
500
19
1400
1320
40
150 150
350
500
19
350
40
110 110
312
40 40
110 110
1500
1420
19
40
350
55
623
350
110 110
40
500
19
2 Fixing frame (base) of an individual panel or panel block

19
312
150 150
462
14 x 28
713
610
28 x 14
40
63
3 Floor opening for high-voltage cables and, if applicable, control cables
7 Position of the incoming cables for the feeder
B Cutout in the mounting frame for extended floor opening for

panel with cable-type current transformers
4
2
4
55
623
55
14 x 28
713
610
28 x 14
623
63
14 x 28
713
610
28 x 14
63
4
2
4
2
4
• For ring-main
panel block
type R-B3
• For ring-main/
transformer
panel block
type 2RT-B3
• For ring-main/
transformer
panel block
type 3RT-B4
• For trans-
former
panel block
type T-B3
Dimensions
Siemens HA 41.11 · 2003 35

aa
³15
36
Dimensions

HA41-2478 eps
³15
³15 480
150
1
HA41-2479a eps
1
HA41-2480a eps
³15
1
HA41-2481a eps
31
233 122 69
47 197
480
150
480
150
480
150
31
35
10
19
40
15
233 122 69
197
31
233 122 69
110 197
42
31
233 122 69
aa
65 150 130 197
Siemens HA 41.11 · 2003

Special versions
35
10
19
40
35
10
19
40
35
10
19
40
175
106 100
350
110 110
270
320
175
110 110
270
110 110
106 100
175
350
270
110 110
106 100
~245*
270
55
623
~101*
4
14 x 28
713
28 x 14
55
648
8, 9
55
~190*
728
55
923
63
425
50 135
14 x 28
713
635
28 x 14
818
715
28 x 14
14 x 28
1013
28 x 14
63
63634
2
4
9, 10
900
4
8
4
type RK
type K
For individual panels with cable-type current transformers

or surge arresters
350
4
2
type RK
type K
(panel depth 775 mm), standard or 25 mm deeper cable compartment cover
175
350
14 x 28 4
2
type RK
type K

type RK
type K
19
40
³15
1
1
HA41-2482a eps
³15
420
HA41-2483a eps
³15
1
HA41-2484a eps
480
150
480
150
480
150
31
233 122 69
197
28 x 14 4
31
8, 9
For individual panels with double cable connection or surge arresters make Tyco Electronics Raychem, type RDA 24
233 122 69
110 197
42
For individual panels with double cable connection (panel depth 880 mm), 105 mm deeper cable compartment cover
4
2
31
233 122 69
65 150 130 197
For individual panels with double cable connection (panel depth 1075 mm), 300 mm deeper cable compartment cover
Legends and footnotes see page 37
35
10
35
10
19
40
35
10
19
40
250
500
150 150
250
500
150 150
106 125 125
250
420
500
150 150
~245*
106 125 125

420
55
648
~101*
55
728
~190*
55
923
14 x 28
713
635
14 x 28
818
715
28 x 14
14 x 28
1013
28 x 14
63
63
63
900
4
2
4
2
4
8
4
2
4
type RK1
• For circuit-breaker panels
type LS1 and LS2

type RK1
type LS1 and LS2

type RK1
type LS1 and LS2
aa
³15
HA41-2485 eps
³15
HA41-2486 eps
³15
HA41-2488 eps
215
122
233
47 197
215
122
233
47 197
215
122
233
197
65 150 130
19
40
19
40
19
40
aa
Special versions in combination with pressure absorber system

~635***
~675**
b
~675***
~101*
~675**
~245*
c
b
c
b
115
713
28 x 14
115
719
115
1013
2 Fixing frame (base)

828
550
240
12
13
4
28 x 14
1128
28 x 14
550
200
834
550
514
300 mm deeper cable compartment cover
1 Wall distance
of an individual panel or
panel block
3 Floor opening for high-
voltage cables and, if
applicable, control cables
4 Fixing points
834
For individual panels with single cable connection
a 11
12
4
2
8
11
7
2
For individual panels with double cable connection

standard or 25 mm deeper
cable compartment cover
a 11
2
12
3
4
type RK and RK1
type K
type LS1 and LS2
• For transformer panels
type TR

type RK and RK1
type K
type LS1 and LS2

type RK and RK1
type K
type LS1 and LS2
• For transformer panels
type TR, however connec-
tion with bolted contact
(M16)
7 Position of the incoming

cables for the feeder
8 Position of 2nd cable
9 For surge arrester
10 For cable-type current
transformers with outside
diameter up to 90 mm
11 Pressure absorber duct
12 Front edge of base
³15
HA41-2487 eps
of the pressure absorber system

13 Front edge of panel
without cable compartment cover
215
122
233
65 85 197
19
40
~675***
~190*
Dimensions
a
c
b
115
824
a = Panel width
b = Width of
550
343
28 x 14
floor opening
c = Fixing
(values see
pages 34 and 35)
939
11
2
12
4
Dimensions

type RK and RK1
type K
type LS1 and LS2

105 mm deeper cable compartment cover
* Dependent on the type of

cable plug employed
** For panel types RK, K and LS
*** For panel types TR, connection
with plug-in contact
B Cutout in the mounting frame
for extended floor opening for
panel with cable-type current
transformers
Siemens HA 41.11 · 2003 37

Dimensions
aa 63
63
HA41-2489 eps
63
aaa
HA41-2339c eps
Cable-connection fittings in ring-main, cable and circuit-breaker panels

(non-binding examples, for further examples see Catalog HA 40.1)
Cable connection in
ring-main panel
553***
~560**
610
747
~560**
610
775
Standard cable compartment cover
HA41-2340c eps
553***
747
775

HA41-2341c eps
38
63
553***
~560**
150 mm deeper
715
852
880
553***
~560**
900
1047
1075
~190**
~245**
300 mm deeper cable compartment

cover for double cable connection
Siemens HA 41.11 · 2003

1
575
2
575
3
4
18
19
18
575
575
HA41-2342c eps
63
HA41-2343c eps
63
HA41-2344e eps
63
HA41-2345c eps
63
Cable connection with
surge arresters
553***
~560**
610
747
775
553***
~560**
610
747
~560**
775
553***
610
25 mm deeper
772
800
300****
553***
~560**
610
150 mm deeper
897
925

5
575
7
575
8
575
10
9
575
11
12
HA41-2346c eps
63
HA41-2490 eps
63
HA41-2347c eps
63
Connection in
circuit-breaker panel
560
610
~560
747
775
13
575
553***
635
747
775
290*
101
14
15
575
553***
~560**
610
150 mm deeper
897
925
* Max. mounting space

for cable plugs
** Dependent on the type
of cable plug
*** Dimension for bushing as
interface type “C” with
bolted contact (M16)
**** Mounting depth for
combination of cable T-plug
and surge arrester
16
575
17
1 Elbow adapter, make: Siemens,
type AKE 20/630 with
conventional cable sealing end,
make: Corning Cables, type IAE 20
2 Cable T-plug, make: Euromold,

types K400 TB/TBS

type K400 TB
type K400 TB as 2nd cable
(option: cable elbow plug
type K400 LB);
always same make required
5 Elbow adapter, make: Siemens,

type AKE 20/630 with
conventional cable sealing end,
make: Corning Cables, type IAE 20
6 Surge arrester,
on request
make: Siemens, type 3EG2
7 Cable plug,
make: Tyco Electronics Raychem,
type RICS 5139
8 Surge arrester,
make: Tyco Electronics Raychem,
type RDA 21 (for type RDA 24,
a floor opening of 635 mm
instead of 610 mm is required)
9 Cable T-plug,
make: ABB Energiekabel,
type SET (12/24)
and
10 Surge arrester
type MUT (13/23)
or:
9 Cable connector, make: nkt cables,
type AB 24-630
and
10 Surge arrester
make: nkt cables, type ASA 24-5

types 400 TB / K400 TB
12 Surge arrester, e.g.
make: Euromold,
types 156 SA, 400 Pb
or similar designs
13 Busbar system
for billing metering panel
type ME1
14 Cable T-plug,
make: nkt cables, type CB 24-630
15 Coupling connector,
make: nkt cables, type CC 24-630
16 Cable T-plug,
make: Euromold, type K400 TB
17 4MT8 plug-in voltage transformer
18 Cable T-plug,
type SET 24
19 Coupling insert,
type KU 23.2
Standards
Standards, specifications, guidelines Notes

Overview of standards (December 2002)
IEC standard VDE standard EN standard If not stated otherwise on
up to now current in future current in future current
the individual pages of this
catalog, we reserve the right
Switchgear IEC 60 694 * IEC 60 694 * IEC 62 271-1 VDE 0670 Part 1000 VDE 0671-001 EN 60 694
to include modifications,
IEC 60 298 * IEC 60 298 * IEC 62 271-200 VDE 0670 Part 6 VDE 0671-200 EN 60 298 especially regarding the
Devices 1) IEC 60 056 ** IEC 62 271-100 IEC 62 271-100 VDE 0670 P. 101 to 106 VDE 0671-100 EN 60 056 stated values, dimensions
2) IEC 60 129 ** IEC 62 271-102 IEC 62 271-102 VDE 0670 Part 2 VDE 0671-102 EN 60 129 and weights.
3) IEC 60 265-1 * IEC 62 265-1 * IEC 62 271-103 VDE 0670 Part 301 VDE 0671-103 EN 60 265-1 Drawings are not binding.
4) IEC 60 420 ** IEC 62 271-105 IEC 62 271-105 VDE 0670 Part 303 VDE 0671-105 EN 60 420 All product designations
5) IEC 61 243-5 IEC 61 243-5 IEC 61 243-5 VDE 0682 Part 415 VDE 0682 Part 415 EN 61 243-5 used are trademarks or
6) IEC 60 282 IEC 60 282 IEC 60 282 VDE 0670 Part 4 VDE 0670 Part 4 EN 60 282 product names of
Degree of IEC 60 529 IEC 60 529 IEC 60 529 VDE 0470 Part 1 VDE 0470 Part 1 EN 60 529 Siemens AG or other
protection suppliers.
Insulation IEC 60 071 IEC 60 071 IEC 60 071 VDE 0111 VDE 0111 EN 60 071 If not stated otherwise,
Current IEC 60 044-1 IEC 60 044-1 IEC 60 044-1 VDE 0414 Part 1 VDE 0414 Part 1 EN 60 044-1 all dimensions in this
transformers catalog are given in mm.
Voltage IEC 60 044-2 IEC 60 044-2 IEC 60 044-2 VDE 0414 Part 2 VDE 0414 Part 2 EN 60 044-2
transformers
Standards
The 8DH10 switchgear
complies with the relevant
standards and specifications
applicable at the time of
type tests.
In accordance with the
harmonization agreement
reached by the countries of the
European Community, their
national specifications
conform to the IEC standard.
Responsible for
Technical contents:
1) Circuit-breaker
Christoph Maul
2) Disconnector and earthing switch Siemens AG,
3) Switch-disconnector Dept. PTD M2 S2
4) Switch-disconnector / Erlangen
fuse combination
General editing:
5) Voltage detection systems Gabriele Pollok
6) HV HRC fuses Siemens AG,
Dept. PTD CC T
Erlangen
* In future, these standards
will be summarized in IEC 62 271 Printed in Germany
(switching devices and switchgear) KGK 06.03 11.0 VO/- 36 En
100637 6101/D6269
** Standard withdrawn
Siemens HA 41.11 · 2003 39
If you have any questions about
Power Transmission and Distribution,
our Customer Support Center
is available around the clock
Tel: +49 180 / 524 70 00 (Subject to changes,
Fax: +49 180 / 524 24 71 e.g.: 12 ct/min.)
E-Mail: support@ptd.siemens.de
www.siemens.com/ptd-support
Published by
Siemens AG
Power Transmission and Distribution
Medium Voltage Division
Postfach 32 20
91050 Erlangen
Germany
www.siemens.com/medium-voltage-switchgear Order No.: E50001-K1441-A101-A4-7600

8DH10 Katalog en

Uploaded by

Copyright:

Available Formats

8DH10 Katalog en

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

8DH10 Katalog en

Uploaded by

Copyright:

Available Formats

Medium-Voltage

Contents Application, Requirements

option: 105 mm or 300 mm

the pressure absorber system,

Siemens HA 41.11 · 2003 3

Rated voltage Ur kV 7.2 12 15 17.5 24 Pressure values at 20 °C

Transformer panel type TR

Circuit-breaker panel type LS, bus sectionalizer panel type LT1

Rated short-time for switchgear with tk = 1 s up to kA 20 25 20 25 20 25 20 25 20

1) The rated normal currents apply

4 Siemens HA 41.11 · 2003

* For free-standing arrangement

Switchgear installation with

3 Panel depth of the standard

10 Height of the cable

Switchgear installation with rear-side

9 2nd cable connected by means

19 Width of the pressure absorber duct

Siemens HA 41.11 · 2003

Shipping data Product range overview

Transport of individual panels

Transport of panel blocks Transformer panel with

1 T1 = Depth of individual Panel blocks

6 Siemens HA 41.11 · 2003

Siemens HA 41.11 · 2003 7

Ring-main panels, cable and transformer panels as individual panels

Ring-main panels Cable panels Transformer panels

option option option 4MT8 plug-in voltage

with plug-in with plug-in with plug-in

2nd cable (not

as transfer panels as transfer panels as transfer panels

option Type RK-U Type K-U option Type TR-U Plug-in

to the right to the right to the right

option Type RK-U Type K-U option Type TR-U

for transfer for transfer for transfer * Deep cable

Ring-main panels, cable and transformer panels in panel blocks

Ring-main panel blocks Ring-main/transformer panel blocks

1050 mm wide 1050 mm wide

Transformer panel blocks 1400 mm wide

Designs and options for each panel, see page 8 consisting of

Cable connection/transformer panel block

1500 mm wide 700 mm wide

* A plug-in voltage transformer cannot be provided at the connection

Siemens HA 41.11 · 2003 9

Circuit-breaker panels as individual panels

Circuit-breaker panels Circuit-breaker panels with metal-enclosed

HA41-2243 _1c eps

as transfer panels as transfer panels

option option Plug-in

option Type LS1-U option Type LS2-U

for transfer for transfer * Deep cable

Bus sectionalizer Busbar earthing Busbar voltage metering

Type LT2 Type SE2

Siemens HA 41.11 · 2003 11

Air-insulated metering panels as transfer panels

Scheme 3 Scheme 3 Scheme 3

Scheme 4 Scheme 4 Scheme 4

12 Siemens HA 41.11 · 2003

Air-insulated metering panels as transfer panels

option option P2 P1 included in the