SURVEYING INSTRUMENTS

Series110M
SET3110M . SET4110M Auto Pointing Total Stations

The time consuming sighting operation has now been automated.

Pointing, Measuring and Display of Result --- All can be done with a Single Key Operation!
Point the telescope approximately to the prism through the peep sight, then simply press the measuring key. The Series110M will automatically point and measure. The measured result will be displayed instantaneously. Automatic pointing system eliminates looking through the telescope. No focusing is necessary. Therefore, even an inexperienced operator can make accurate measuring. - Reduces Stress Eyestrain will be relieved, as looking through the telescope is not necessary. Survey work will be extremely facilitated as physical stress is relieved. - Automatic Pointing of Long Distance A distance up to 800m (2,600ft.) with a single prism and a distance up to 300m (950ft.) with a pinpole prism can be pointed automatically. - Automatic Pointing Made Easy Under Twilight Conditions The Series110M will accurately and quickly point to the object even under unfavorable twilight conditions at dusk or at dawn.

A MOTOR DRIVE TECHNOLOGY THAT MAKES HIGHLY ACCURATE AUTOMATIC POINTING AND POSITIONING POSSIBLE
- Equipped with Sokkias Original Drive Mechanism and Control Algorithm. A highly accurate automatic pointing and angle positioning are made possible, thanks to the original gear reduction mechanism and the control algorithm using angle information obtained directly from the angle-measuring encoders. - Jog Dial (Variable Speed Fine Coarse Dial) Equipped with a Fine /Coarse Variable Speed Jog Dial for adjusting vertical and horizontal rotation. The feed rate will be changed automatically depending on the speed of turning the dial. Positioning to the target point can be made as smoothly as with the manual total stations.

Efficiency upgraded, drastically reduces operator fatigue by eliminating the need for looking through telescope. Sokkias Series110M Total Stations dramatically improve the work efficiency.

- Self-lock, Free Rotation Mechanism Accelerates Job Efficiency. To enhance handling efficiency, the mechanical clamps have been eliminated and a self-locking mechanism is employed which automatically locks the telescope position. Also, the free rotation mechanism enables to freely rotate the telescope with hands.

THE PRINCIPLE OF AUTO POINTING

A laser beam for auto pointing is emitted from the center of the telescope. The vertical and horizontal line-CCDs located co-axially with the telescope receive the laser beam reflected from the prism and capture the beam position. The control unit instantly calculates the deviation from the telescope optical axis. Based on this calculation, the vertical and horizontal motors will respond simultaneously to align the sighting axis to the prism center. The high resolution line CCDs and the high speed processing capability enables to obtain a high accuracy of within 2.5 mm (0.1in.) for distances up to 100m(330ft.) and within 5 for distances beyond 100m. The safe, Class 1 laser beam will not harm the eyes.

THE GUIDE LIGHT SUPPORTS SETTING OUT

The guide light supports the alignment of prism to the telescope sighting line. The guide light will be seen as red when it is at right side, and will be seen as green if it is at the left. The center position can be easily recognized even at close distance as the two lights are emitted through a single outlet. The guide light can be seen for a distance up to 170m (560ft.). The brightness can be adjusted in 3 steps. The Class 1 LED is safe and will not harm the eyes.

A WIDE AREA AUTOMATIC POINTING

The automatic pointing search area is not limited to the inside telescope sight range. Even an inexperienced operator, who is unfamiliar with peep sight rough pointing, by selecting the wide search area,
1. [Within the telescope sight] Suitable for operators who is familiar with rough pointing. Speedy measuring is possible. 3. [Oblong] Suitable for surveying at a flat land.

can do accurate measuring. When operating the unit using a wireless controller from the prism side, the prism can be found easily by utilizing the various search functions.
2. [Wide] Suitable for inexperienced operators. 4. [Oblong, vertical] For measuring and setting out in places of large hight differences.

1 2
10m/100m (30ft./330ft.) 2.6m/100m (8.5ft./330ft.)

4 3
13m/100m (40ft./330ft.) 13m/100m (40ft./330ft.)

800m (2,600ft.)

300m (980ft.)

Series110M Specifications
Telescope Length Objective Aperture Magnification Image Resolving power Field of view Minimum focus Reticle illumination Focusing ring Angle measurment Unit Display resolutions Accuracy (ISO 12857-2 1997) Measuring time Automatic dual-axis compensator SET3110M SET4110M Fully transiting, coaxial sighting and distance measuring optics. 165mm (6.5in.) 45mm (1.8in.) [EDM:50mm (2.0in.)] 30x Erect 3 130(26m/1,000m) 1.2m (4.0ft.) Bright or dim selectable Fine/Coarse two-speed motion Photoelectric incremental rotary encoder scanning with 0 index Degree/Gon/Mil, selectable 1"/5", 0.2mgon/1mgon, 0.005mil/0.02mil, selectable 3(1mgon) 5(1.5mgon) Less than 0.5sec., continnous ON (V&H,V only) / OFF selectable Dual-axis liqid tilt sensor 3 (55 mgon), out-of-range warning display provided Digital/graphic reslution: according to angle display resolution ON/OFF selectable Clockwise / Counterclockwise, selectable. 0-set / Hold / Angle input, available Zenith 0, Horizontal 0, Horizontal 0 90, slope in%, selectable Modulated near infrared light (IEC Class 1 LED) 3 to 80m (260ft.) 1.2 to 300m (980ft.) 1.2 to 600m (1,900ft.) 1.2 to 1,600m (5,200ft.) (2+2ppm x D)mm (5+2ppmx D)mm (4+2ppmx D)mm (5+2ppmx D)mm Every2.0sec.(initial meas.3.7sec.) Every0.9sec.(initial meas.2.1sec.) Every0.4sec.(initial meas.1.9sec.) Meters / Feet / Inch, selectable 0.001m (0.01ft. / 1/8in.) 0.001m (0.01ft. / 1/8in.) 0.01m (0.1ft. / 1/2in.) Fine meas.(single/repeat/average) / Rapid meas.(single/repeat) / Tracking, selectable Temperature, pressure, humidity, ppm input available -99 to + 99mm (1mm steps) ON (K=0.142/0.20)/OFF selectable DC motor drive with self-locking free rotation system Fully transiting Less than 10sec. for 180 rotation (compensator off) Variable speed jogging knobs Pulse Laser transmitter and CCD detetor with co-axial optics Laser diode, wavelength 785nm (IEC Class 1 laser, FDA Class I laser) 2 to 300m 2 to 400m 2 to 800m Better than 2.5mm (0.1in.) up to 100m (330ft.) Better than 5 (1.5mgon.) over 100m (330ft.) 3 to 6sec. typically (with a prism at 100m distance) Red LED (626nm) and Green LED (524nm) (IEC Class 1 LED) Up to 170m (560ft.) Approx: 4m/100m (13ft./ 330ft.) (more than 2.5 from telescope axis) Approx: 3.5m/100m (11ft./ 330ft.) (more than 2 from telescope axis) Approx: 12cm3cm/100m (4.7in. 1.2in./ 330ft.) (4'1') Approx. 20,000points Asynchronous serial, RS-232C compatible, baud rate:1,200 to 38,400bps Alphanumeric / graphic dot matrix LCD 20 characters x 8 lines, on single face (Face 1) with backlight Alphanumeric, 28 keys Alphanumeric, 28 keys Trigger key, 1 key 3'/outer circle 10'/2mm 30/2mm Provided Image:Erect, Magnification: 3x, Minimum forcus: 0.5m (1.6ft.) -20 to +50C (-4 to + 122F) 245mm (9.6in.) from tribrach bottom, 202mm (8.0in.) from tribrach dish W202 x D165 x H380mm (W8.0 x D6.5 x H15.0in.) Approx. 7.1kg (15.7lbs) Working duration Charging time Working duration About 4 hours*3 Approx 130 min. with standard charger CDC56 more than 7 hours*3 4 steps with warning message 30 minutes after operation / OFF, selectable more than 3 hours*3

H&V H&V H&V Type Range Display

Collimation program Measuring mode

H V

Distance measurement Measuring range With RS90N-K reflective sheet target (slope distance*1) With OR1PA pinpole prism With CP01 compact prism With one AP01 prism Accuracy With prism Fine meas. Rapid meas. (D=measuring distance; unit:mm) with reflective sheet target Fine meas. Rapid meas. Measuring time Fine meas. Rapid meas. Tracking meas. Unit Display resolution Fine meas. Rapid meas. Tracking meas. Measurement mode Atmospheric correction Prism constant correction Refraction&earth-curvature correction Motor drive Rotating angle H&V Positioning speed H&V Fine motion H&V Auto pointing Light source Distance range With OR1PA pinpole prism With CP01 compact prism With one AP01 prism Auto pointing accuracy Auto pointing time*2 Guide light Visible range*2 Visible width Center resolution (horizontal) General Data storage Interface Display Keyboard Sensitivity of levels Face1 Face2 Graphic LCD level Circular level (in tribrach) Plate level

H V

Calendar-clock function Optical plummet Operating temperature Tilting / Trunnion axis height Size with handle and battery Weight with handle and battery Power supply BDC45 Ni-MH detachable battery Optional external battery BDC7 Battery level display Automatic power cut-off

*1 Under average conditions. Slight haze,visibility about 20km(12miles), sunny periods,weak scintillation. *2 Values vary according to the environmental conditions. *3 Single measurement alternately at each face with 30-second intervals, using auto pointing function, at 25C (77F).

Sokkia is a trademark of Sokkia Co., Ltd. Designs and specifications are subject to change without notice.

Sokkia is a sponsor of the international Federation of Surveyors.

ISO9001 Certified (JQA-0557)

http://www.sokkia.co.jp/english/ INTERNATIONAL SALES DEPARTMENT PHONE +81-46-248-7984 FAX +81-46-247-1731 260-63 HASE, ATSUGI, KANAGAWA, 243-0036 JAPAN
A-199-E-2-0310-NP-AB Printed in Japan on 100% recycled paper with ecologically safe soy ink.