200 AutoCAD Commands (3rd Edition)

2 0 0
AUTOCAD
COMMANDS
Third Edition
www.thesourcecad.com
BY: Jaiprakash Pandey
INTRODUCTION
AutoCAD has thousands of commands. This
book however contains 200 of the most useful
commands that one should definitely know.
The command list here focuses on usability

rather than listing commands for the sake of it.
This book is great for a beginner as well as an

experienced AutoCAD user. A beginner will find
lots of new commands to learn the software
from scratch and a seasoned user will find many
new commands that will improve their
productivity.
The commands are divided into different

categories to make them easy to remember and
wherever applicable a link to a detailed video
or article explaining the command is added as
well.
O1 Keyboard shortcut keys
Page 4 - 7
O2 Status bar toggle

Page 8 - 13
O3 Basic AutoCAD commands

Page 14 - 21
O4 General commands
Page 22 - 37
O5 Performance related commands

Page 38 - 50
CONTENTS
O6 Accesibility commands
Page 51 - 61
O7 3D commands
Page 62 - 71
O1
KEYBOARD
SHORTCUT
KEYS
Keyboard shortcuts or hotkeys are the shortest and

quickest way of activating some of the common AutoCAD
operations or commands. In this list, I have included some
of the most frequently used and useful keyboard
shortcuts
Ctrl + N
You can use this shortcut to open a new drawing tab in
AutoCAD.
Ctrl + S
You can use this keyboard shortcut to save a drawing file.
Ctrl + Shift + S
You can use this keyboard shortcut to save the drawing as a
new file, in short, this is the hotkey for “save as” command.
Ctrl + 0
Clears screen to show only the drawing area and hides
palettes and tabs. Press it again to reset the default AutoCAD
interface.
Ctrl + 1
Select an object and press Ctrl + 1 to open the properties
palette which lists the properties of the object. You can use
this palette to modify most of the properties of the object
too.
You can also use the PR command to open the property

palette.
5
Ctrl + 2
You can use it to open design center palette which contains
many AutoCAD blocks that can be used directly in your
drawing.
Ctrl + 8
You can use this to open a quick calculator inside the

AutoCAD user interface to perform simple and complex
calculations using the scientific calculator and also for unit
conversion calculations.
Ctrl + 9
You can use this keyboard shortcut to toggle the visibility of
the command line.
If for some reason your command line is hidden from the

drawing area, then use this keyboard shortcut to bring it back.
Ctrl + C
Select objects from the drawing area and press Ctrl + C to
copy to objects to the clipboard.
6
Ctrl + V
To paste the copied objects of the clipboard in the drawing
keeping their original properties, you can use this keyboard
shortcut.
Ctrl + Shift + V
To paste the copied objects as a block you can use this
keyboard shortcut, the block thus created will have a random
set of characters as its name.
You can use this keyboard shortcut to make blocks quickly

without going through the create block window.
Ctrl + Z
This keyboard shortcut can be used to undo the last action in
your drawing. You can press this shortcut key multiple times
to undo many actions.
Ctrl + Y
This keyboard shortcut can be used to redo the last undo
action which you have performed.
Ctrl + Tab
You can use this keyboard shortcut to cycle through all open
drawing tabs in AutoCAD.
7
O2
STATUS BAR
TOGGLE
The status bar is an important feature of the AutoCAD user

interface and its tools are required quite frequently while
making or editing your drawing hence they are available on
the status bar for easy access. You can activate or deactivate
status bar icons using keyboard shortcuts, commands or by
clicking on their respective icon.
F3
One of the most important status bar toggles. This function
key activates/deactivates the object snap option, when object
snap is active you will be able to snap your cursor to some
exact points in the geometry like End, centre, quadrant,
tangent etc. Using this option you can make precise AutoCAD
drawings.
F6
Dynamic UCS can be activated or deactivated using this
function key. Using dynamic UCS you can make geometries
directly of the face or another 3D object irrespective of the
position of UCS. You can also toggle dynamic UCS using
UCSDETECT system variable, the values of this system
variable can be 1 for ON and 0 for OFF.
F7
This status bar tool will toggle the visibility of the background
grid which is often visible in your drawing area.
9
F8
Toggles Ortho mode on/off. When ortho mode is on you can
make lines either horizontally or vertically only.
F9
Toggle Snap mode, when the snap mode is active AutoCAD
cursor will jump to specific points in the drawing area which
is defined in snap mode.
F10
Toggles Polar tracking on/off. With polar tracking active you
can make lines inclined to any angle which is defined in the
polar tracking increment angle.
F11
Toggles Object snap tracking on/off. Using this option you can
track snap points of geometries like centre, midpoint,
endpoint etc and make geometries with their reference.
10
DYNMODE
By default, the value of this system variable is set to -3 which
keeps it off you change this system variable to 3 to make
dynamic input active. Dynamic input allows you to add
information dynamically on the cursor tooltip.
ISODRAFT
Using this toggle you can activate the isometric drawing plane
in AutoCAD. You can select from Isoplane Left, Isoplane Top
and Isoplane Right.
You can also toggle between different isoplanes using F5

function key. The default value of ISODRAFT option is
orthographic.
LWDISPLAY
This system variable toggles the visibility of lineweight in a
drawing. The default value of this system variable is OFF
which keeps the lineweight display off you can change its
value to ON to keep lineweight visible in the drawing area.
11
TRANSPARENCYDISPLAY
Just like lineweight this status variable allows you to toggle
the visibility of transparency of an object.
You change the value of this system variable to 1 to make

transparency visible or 0 if you want to make it invisible.
SELECTIONCYCLING
Using this system variable you can select overlapping objects
very easily.
When the value of this system variable is set to 2, an

overlapping icon and a menu containing a list of overlapping
objects appear and you can select the required object from
this list.
If you set the value of this system variable to 1, only the

overlap icon appears not the menu. You can turn this off by
changing the value of this system variable to 0.
12
GRAPHICSCONFIG
Using this status bar option you can open the Graphics
configuration window which is used to change settings
related to the display and graphics properties of AutoCAD.
You can also use 3DCONFIG for opening the graphics

performance window.
13
O3
BASIC AUTOCAD
COMMANDS
These are some of the Draw and Modify commands which

make the very basics of AutoCAD and if you are just
starting to learn AutoCAD then you should know all of
these basic commands.
L
It can be used for making simple lines in the drawing.
C
It is the command used for making a circle in AutoCAD.
PL
This command can be used to make a Polyline in your
drawing.
REC
This command will make a rectangle in AutoCAD.
POL
This command can be used to make a polygon with minimum
of 3 sides and a maximum of 1024 sides.
ARC
As the name suggests, this command can be used to make
an arc in AutoCAD.
REG
This command can be used to make a region geometry in
AutoCAD.
15
ELLIPSE
As the name suggests, this command can be used to make an
ellipse with the major and minor axis.
CO
This command is used to copy object(s) in AutoCAD.
ARRAY
Using this command you can make Rectangular, polar or
Path array.
TR
This command is used for trimming a geometry.
EX
This command extends the selected object to meet the
reference object which is selected.
16
I
This command can be used to insert an existing block or a
drawing as a block in AutoCAD.
OP
Using this command you can open options window which
contains most of the settings of AutoCAD.
ST
Using this command you can open text style window which
controls properties of the default AutoCAD text style.
X
This command can be used to explode objects like Polyline to
simple lines, an array or a block to a simple geometry etc.
17
F
This command can be used to add rounded corners to the
sharp edges of the geometry, these round corners are also
called fillets.
CHA
This command can be used to add slant edges to the sharp
corners, these slant edges are also called chamfers.
B
This command is used for creating a block, the properties of
the block can be defined using the block definition window.
LA
This command can be used to open layer properties manage
palette which is a tool for creating and managing layers in a
drawing.
18
REVCLOUD
Using this command you can make a revision clouds that are
essentially drawing markup tools.
POINT (PO)
This command makes a single point geometry in the drawing.
To modify the type of point created by this command you can
use PTYPE command and choose the desired point type from
Point Style window.
SKETCH
You can make a freehand sketch using this command. You can
use Line, Polyline or Spline as the object type for making this
freehand sketch.
Check this animated image for an example.
19
DONUT
It creates two circles with a filled area in between by inputting
the inner and outer dimension of the two circle.
ML
Multiple parallel lines can be created using this command.
This command is great for making walls with predefined
thicknesses.
SPL
Using this command the user can create smooth curves with
control points for changing the curvature of the sketch.
Following image shows an example of spline.
DT
Starts the single line text command in AutoCAD which
perhaps is the most basic texting command in AutoCAD. This
allows to insert the text in a single line.
20
MT
This allows the user to insert text in Multiline text format.
Mostly this is used to insert a large text or a paragraph.
Mtext Is also associated with a text editor dialogue box where

the user can make many changes and text formatting in the
software itself.
DJO
Jogged dimensions can be created and marked in the drawing
using this command. A jogged dimension is shown in the
following image.
SC
This command is used to change the scale of an object.
21
O4
GENERAL
COMMANDS
These are some of the commands which can be frequently

used in your drawing workflow to improve your overall
efficiency. You might be familiar with many of these
commands but there are also some commands which are
really helpful still they remain largely unused.
COUNT
This command shows the number of blocks in a drawing in
tabular form. You can select the entire drawing or a specific
area from the drawing to count the blocks from.
PEDIT
This command will start the Polyline edit tool that you can
use to edit polylines or convert 2D geometry like lines and arc
into a polyline.
23
MULTIPLE
If you want to repeat any command without pressing enter
key then use MULTIPLE command. To cancel repetition of
command press ESC key.
NCOPY
Use this command to copy nested objects from a block or Xref
without exploding them.
‘CAL
Using this subcommand you can perform calculations directly
on the AutoCAD command line even when you are in the
middle of a command.
You can start this subcommand by entering ‘CAL (don’t forget

to add an apostrophe before CAL) while running any other
command.
BURST
Explodes the block containing attributes retaining the
attribute setting and its layer definition. This is especially
helpful if you want to retain the text of the attribute after
exploding the block.
24
ARCTEXT
This command can be used to write arc-aligned text in
AutoCAD. This command has options for changing text
formatting and text alignment direction along the arc.
SP
Using this command you can check the spelling of selected
text and correct the spellings from Check Spelling window.
OOPS
This command can be used to restore the last deleted object
in your drawing.
After deleting an object if you made many other changes in

the drawing and realized that you might need to restore the
deleted object then simply type OOPS and press enter.
25
CHSPACE
This command can be used to change the space of an object
from model space to paper space and vice versa. See the
animated image shown below for reference.
DIVIDE
You can use this command to divide any 2D geometry into
many equal parts. At each point of division, a point geometry
will be added to the 2D curve.
RENAME
If you need to rename any named object like layer, block or
linetype simply use this command to rename it. More about
this command can be found in this related article.
BREAK
This command can be used to break 2D geometries at one or
two points.
It is helpful if you want to break a curve at the point of

intersection with another curve or if you want to create a gap
by breaking a part of the geometry.
26
DI
It can be used to find the distance between two points in the
drawing.
TIME
Using this command you can find a lot of information about

your drawing like the date when the drawing was created and
total editing time consumed on the drawing.
QSELECT
This command can be used to make the selection from your
drawing with filters.
As an example, you can use quick select to make a selection

set containing all circles of the drawing with the radius of a
particular value.
COPYBASE
Using this command you can copy any object using a base
point.
27
PASTECLIP
You can paste the copied objects from the clipboard to your
drawing using this command.
If you use COPYBASE to copy the objects then you will be able
to paste them into the same or another drawing with the
selected base point.
LIST
Using this command you can find lots of properties of an
object like the layer they are on, area, length or radius,
perimeter or circumference and a lot more.
To use this command simply type LIST on the command line

then press enter and select the object from the drawing area
about which you want to know and press enter again.
TJUST
Using this command you can change the text justification of
Text and Mtext elements in the drawing.
28
DIM
This command was introduced in AutoCAD 2016 version and it
can be used to make most of the dimensions like Linear,
aligned, radius, diameter and baseline.
To access this command you can use DIM command or select

the DIM tool from dimensions panel of Annotate tab.
TOLERANCE
If you want to add a feature control frame representing
tolerance related information in your drawing then you can
use this command.
ML
Using this command you can make a multiline geometry
which contains multiple parallel lines.
29
SCALETEXT
Using this command you can change the scale of existing Text
or Mtext object in the drawing.
To use this command type SCALETEXT on the command line

press enter and select the text from drawing area and press
Enter again.
Now select “Existing” option from the command line and then
select “scale factor” option and then type the scale in which
you want to convert the text height and press enter.
When the scale of these text entities are changed the base
point will remain fixed.
BASE
Using this command you can change the base point of a
drawing without changing its origin.
This is especially helpful in the situation where you want to

insert the drawing into another as an Xref.
By default, AutoCAD takes origin as the base point which can

be modified using this command without changing the origin.
ID
This command can be used to find the coordinate values of a
point in AutoCAD drawing.
30
DWGPREFIX
If you have a drawing open in AutoCAD and you don’t know
the location where it is saved you can simply type DWGPREFIX
command to look it.
This command can be used to quickly find the location of

Xref’s attached in the drawing.
UNITS
Using this command you can set the drawing units and other
settings like the precision of linear and angular dimensions
and default rotation angle.
31
TINSERT
You can insert a block or a drawing as a block in the table
using this command.
You can also fit the block in the table cell and also justify its
location automatically with TINSERT dialogue box.
I have made a simple table by importing blocks of design

center as shown in the image below.
MIRRTEXT
By default, AutoCAD does not mirror text in the drawing but if
you want to mirror the text of your drawing then change the
value of MIRRTEXT system variable to 1.
32
AREA
As the name suggests this command can be used to find the
area of closed or open shapes in the AutoCAD drawing.
TORIENT
Using this command you can reorient text entities in the best
readable position.
In image A below the text is oriented at different angles and in

some situations, the text is not properly readable.
Whereas in image B below TORIENT command has been used

to make the text readable for all angles.
MINSERT
Using this command you can insert existing blocks of a
drawing as a rectangular array component. An array added
using MINSERT command can’t be exploded.
33
BOUNDARY
Using this command you can extract closed boundaries from
any enclosed area.
This boundary can be used to find the area of the enclosed

region or for many other applications.
In the image below the boundary of the area mentioned as A

has been extracted as a polyline using BOUNDARY command.
TXT2MTXT
Using this command you can convert a text object into a Mtext
object and you can also combine multiple separate Mtext
objects into a single Mtext unit.
DIMROTATED
This command can be used to make a dimension line inclined
to a particular angle with respect to the positive side of the X-
axis.
34
In the example shown below the dimensions are made with
DIMROTATED command.
BREAKLINE
You can use this tool to make a Breakline symbol on a line.
Type BREAKLINE on the command line and press enter then

click on the scale option of the command line and apply an
appropriate scale to the breakline.
Select the starting and end points of the breakline then click at
any point on the line to specify the location of breakline or
directly press enter to place it exactly at the center of the line.
35
J
This command helps to join similar objects to make them a
single object. For example, different lines drawn continuously
can be joined to make them a polyline.
S
This command helps the user to stretch the object to the
required length. The selection method decides the process of
stretch on the object.
LEN
This command helps to change the length and angle of lines
and arcs.
O
Using this command you can create a replica of the original
sketch at a specified distance from the actual sketch.
HATCH
This command allows to fill up the closed area with a particular
hatch pattern, gradient or solid fill.
GRADIENT
This command allows you to fill up the closed area with a
particular color gradient.
36
FILETAB
You can show the file tab if it is not visible using this
command. To hide the file tab you can use the FILETABCLOSE
command. File tabs are shown in the following image.
TXTEXP
Using this command you can convert single line as well as
multiline text into geometries.
XLINE (XL)
Using this command you can make infinite lines starting from
the point of selection. When you trim or break this infinite
line to a finite length it becomes a simple line geometry.
37
O5
PERFORMANCE
RELATED
COMMANDS
There are several inbuilt tools and commands in AutoCAD

that help you keeping the performance of AutoCAD
optimized. In this section, you will find all those
performance and optimization-related commands which
you can use in your daily workflow.
PURGE
This command can be used to remove unused named
objects like layers, blocks and dimension styles from the
drawing.
LAYDEL
Using this command you can delete some of the most
stubborn layers from your drawing which can’t be removed
using PURGE command.
This command can also remove Defpoints layer and also layer
containing objects but I would not recommend that.
OVERKILL
Use this command to remove overlapping or unnecessary
geometries from the drawing.
RECOVERALL
This command repairs a corrupted or damaged drawing along
with all of its attached Xref’s.
AUDIT
This command should be used for removing errors from
your drawing. It is always a good practice to keep checking
your drawing file with AUDIT tool for errors.
39
FILLMODE
Using this system variable you can turn off or on the visibility
of filled area in hatches or wide polylines by changing its value
to 0 or 1 respectively.
By turning the FILLMODE to off you can enhance the

performance of AutoCAD by limiting resources consumed on
regenerating the filled geometries.
You need to regenerate the drawing using REA command

after changing this system variable to see its effect.
HIGHLIGHT
This system variable is also similar to SELECTIONPREVIEW
but in this case, the object will appear highlighted when
selected. Its default value is 1 but you can turn off this
highlight effect by changing its value to 0.
40
SELECTIONPREVIEW
When hovering the cursor over any object a preview will
appear if the value of this system variable is set to 3.
You can remove this preview thereby improving the

performance by changing the value of this system variable to
0.
ISAVEPERCENT
You can change the value of this system variable to reduce the
time it takes to save a drawing.
This system variable also affects the file size of AutoCAD

drawings and their compatibility with other software.
By decreasing the value of this system variable you can

increase its compatibility with other software and it also
decreases the size of the CAD file but the time consumed in
save operation generally increases.
When you increase the value of this system variable opposite

happens. The default value of this system variable is 50 and it
can be changed from 0 to 100.
41
APERTURE
This system variable controls the area of influence of object
snap. The aperture size as defined by this system variable is
the area of the square under which the point will be selected
if the cursor is brought into it.
The default value of this aperture is 10 but depending on the

complexity of the drawing you can change this value between
1-50.
The size of the aperture is relative to the current scale of the

screen and it is not an absolute value.
In the image below the red box (not visible in AutoCAD) is the
aperture size for two values 10 and 50 respectively.
SAVEALL
As the name suggests this command can be used to save all
of the open drawings in AutoCAD window.
42
PICKBOX
Using this system variable you can change the size of Pickbox
which appears at the cursor of AutoCAD. The default value of
this system variable is 3 and you can change its value from 0
to 50.
In the image below the size of Pickbox is 3 for first cursor and
10 for the second cursor.
CLOSEALL
If you have multiple tabs open in your AutoCAD window and
you don’t want to manually close them one by one then you
can simply use the CLOSEALL command to close all the open
windows.
AutoCAD will prompt you with the save dialogue box before
closing all unsaved drawings and it will take you to start
screen after closing all of the drawings.
CLOSEALLOTHER
Using this command you can close all open drawing
windows except the current drawing window.
43
STARTMODE
This system variable will toggle the visibility of the start tab at
the beginning of the AutoCAD application.
By default the value of this system variable is 1 which allows

the start screen to appear, you can change this value to 0 if
you don’t want to see the start screen.
FILEDIA
This system variable suppresses the dialogue box that opens
up when invoking certain commands like Save, Save As and
Export.
The default value of this system variable is 1 which allows the

dialogue box to open.
When you, however, change the value of this system variable

to 0 the command will run on the command line and the
dialog box will not open.
44
RECOVER
This command is similar to the AUDIT command but it is
useful for the drawings that are corrupted to such an extent
that you can’t even open them.
ZOOMFACTOR
This command controls the magnification of with respect to
the turning of mouse wheel.
Its value is between 3 and 100 with default value set to 60.
Higher the value more will be the effect of zoom wheel
motion.
QP
This command will bring up a quick property window, where
the essential and common properties will be listed for the
objects that are selected.
45
TEXTFIT
Using this command you can shrink or expand the text
entities in a drawing to fit in the required area. In the example
below I have fitted the AutoCAD text within the rectangle
using TEXTFIT command.
WIPEOUT
Using the wipeout command you can clean the background
in a crowded drawing to make overlaying objects clear
against the background.
In the image shown below Wipeout command has been used

to clean the area around the second hook.
You can use the WIPEOUTFRAME system variable and change

its value to 0 to remove the wipeout frame boundary also.
46
-DWGUNITS
Using this command you can convert your AutoCAD drawing
from one unit to another and you can also scale the existing
drawing to new scales automatically.
ANNOMONITOR
When this system variable is ON it shows all the non-
associative dimensions and multileaders with a yellow badge.
When it is set to off it shows no warning badge.
47
TEXTMASK
Using this command you can automatically create masking
behind the text to make it clearly visible against the crowded
background.
In the image below Textmask has not been applied for the
first case and in the second case, it has been applied.
LAYMRG
If you want to merge layers of multiple objects then this
command is for you.
Type LAYMRG press enter key then select the objects whose
layers you want to change then press enter again.
Select any object of the target layer on which you want to

transfer the selected objects and press enter again.
All the objects of the selected layer will be transferred to the

end layer and also the selected layer will be removed.
48
DS
Using this command you can open the drafting settings
window which can be used to change settings related to
status bar options like object snap, polar tracking, snap and
grid settings.
TABLET
If for some reason you are looking to use the Tablet as a
pointing and navigation device in AutoCAD then you can use
this command to turn the Tablet input on and off.
The Tablet can be turned on and off using TABMODE system

variable also.
49
3DCONFIG
You can use this command to Turn on/off hardware
acceleration or change the graphics related properties of
AutoCAD like smooth line display and high-quality graphics
display.
ICL
This commands crops the selected image with respect to the
boundary defined.
50
O6
ACCESSIBILITY
COMMANDS
These commands will help you in making your overall

drawing workflow faster by eliminating the need for using
many repetitive tasks.
TEXTSCR
This command will open a text window which has a history
of recently used commands.
MA
This command is a great time saver if you want to copy
properties of one object on another without changing its
geometry or contents.
CENTERLINE
As the name suggests you can add a centerline easily

between parallel or intersecting lines using this tool. See the
related article for more on Centermark and Centerline tools.
CENTERMARK
This tool was added in the AutoCAD 2017 version and it
allows you to create center mark easily on a circle or arc.
52
LAYMCH
Using this command you can change the layers of selected
objects.
To use this command type LAYMCH on the command line,

press enter key, select objects whose layer assignment you
want to change, press enter, select any entity of the layer you
want to apply to selected objects, and press enter key again.
LAYWALK
Using this command you can check all the objects which are
on a particular layer.
When you use LAYWALK command a list with all layers

appears on the screen and you can click on any of the
layer(s) from the list and objects from that layer(s) will only
become visible in the drawing area.
The original status of layer and object visibility is restored

once you close LAYWALK window.
53
BATTMAN
This tool can be used to modify the attribute information of
blocks containing attributes.
FS
Using this command you can select objects which are
connected to the selected object in the drawing area.
The behaviour of this command is controlled by FSMODE

system variable, if the value of FSMODE is OFF then FS
command will select only the selected object and one object
that is directly connected to the selected object.
If the value of FSMODE is ON then the FS command will

select the selected object as well as all the objects connected
to it and its next connected object in the series.
This selection series continues as long as the command finds

connected objects.
TEXTTOFRONT
Using this command you can bring TEXT, Dimensions and
Leader lines on the front of all underlying objects like hatches.
This command is especially helpful if you want to bring
multiple annotations to the front of all drawings objects
without changing their draw order selectively.
54
ISOLATE
Using this command you can hide all objects from the drawing
area except the selected objects.
By hiding unnecessary objects from drawing you can get a

clean work area.
To bring back all the hidden objects back to the drawing select
UNISOLATE or UNHIDE command.
HIDEOBJECTS
This command is similar to the ISOLATE command but in this
case, you can hide selected objects while keeping the
remaining objects visible.
In this case, also you can bring back hidden objects by using
UNHIDE or UNISOLATE command.
GROUP
Using this command you can group multiple objects as a
single unit.
This command is excellent for making groupings of similar

types of objects like a group of similar blocks.
To break this group you can use UNGROUP command.
55
ADCENTER
This command can be used to bring the Design Center
palette to the drawing area.
You can also use the CTRL+2 key to open the design centre
palette.
FIELD
Fields are dynamic text information which can add a lot of
intelligence to your drawing by keeping data interlinked and
updated.
Fields are extensively used in the sheet set and layout

drawings and they can be used to automate a lot of
information in AutoCAD drawings.
You can start the Field window using the FIELD command of
AutoCAD.
56
IMPORT
Using this command you can import drawings of many
different formats in AutoCAD, the list of all supported
formats is shown in the image below.
WBLOCK
If you want to export a certain part of your drawing or any of
its blocks to an external file then you can use the write block
tool or its command equivalent WBLOCK.
PUBLISH
Using this command you can print multi-sheet files directly,
unlike PLOT command which only plots single sheet this
command will allow you to plot multiple sheets or even all of
the sheets of the drawing directly.
57
TCOUNT
Using this command you can add bullet points and
numbered lists along multiple rows of the text.
An example is shown in the image below, figure A is the text

we used for example and figure B is the result after using
TCOUNT on the rows of texts.
MA
This command is used to transfer properties like lineweight,
transparency, layer, color and more from one object to
another.
LTS
This command changes the scale for the Line Type and
applies throughout the drawing.
LW
This command changes the line weight of the object.
58
ID
The current coordinate of a point can be determined using
this command
EXP
This allows the user to save the drawing to a different file
format as shown in the following image.
MEA
Using this command the user can measure the distance ,
radius,area and volume of the selected object
EPDF
The drawing can be exported and saved as a PDF file by
using this command.
XR
This command opens up an external reference palette and
you can use it to attach DWG, PDF or images in your drawing
as external refernces.
59
RE
This tool is the same as that of a "refresh" function in the
windows operating system. This will regenerate the entire
drawing in the software showing any changes you've made.
BE
This command allows us to edit the block and its
parameters. This command will take the user to an exclusive
block editor window where all the changes can be made and
saved in the block.
MLD
Call out or leaders can be placed in the drawing by using this
command.
MLE
Multileaders size, text etc can be edited using this command.
COMPARE
Using this command you can compare two versions of the
same drawing and all the changes in it.
60
ACTRECORD
Using this command you can record the repetitive actions in
your drawing and replay them again to automate the entire
process without having to write the macros.
SHARE
Using this command you can share your drawing using a URL
with the Autodesk cloud. The recipient can view the drawing
without using AutoCAD software in a browser.
DWGHISTORY
Using this command you can show the history of a drawing
and all the changes made to it. This command will work only
when you save your drawing using a cloud service like Box,
Dropbox or OneDrive.
61
O7
3D COMMANDS
This section has some noteworthy AutoCAD 3D commands

related to solid, surface and mesh modelling. You might be
familiar with many of these commands but there are also
many commands which are not frequently used despite
their great features.
EXT
This command extends the 2D object to the third axis which
is the Z axis, so as to convert it into 3D.
REV
This command helps the user to create a 3D solid by
revolving a 2D region around an axis.
SWEEP
Using this command you can sweep a 2D geometry along a
path. Following image shows an object created with sweep.
BOX
This command will create a 3D box shape without using any
2D base sketch.
CYL
A 3D solid cylinder can be made using this command. Here
the user has to provide the radius or diameter of the base
and then provide the height of the object.
63
PYR
3D Solid pyramid can be created using this command. The

user first has to provide the base dimension and then
provide the height of the pyramid.
LOFT
Using this command you can join two or more 2D curves to

make a lofted 3D object. In the following image red 2D
curves were used to create this lofted 3D.
SL
This tool divides a 3D object or 2D surface into two different

part.
64
THICKEN
Using this command you can convert a surface into a 3D
solid by adding thickness to it.
CONVTOSOLID
Using this command you can convert 3D mesh and
watertight objects made with surfaces to 3D solid and you
can also control whether the converted solid is smooth or
faceted.
POLYSOLID
Using this command you can make a 3D wall-like shape as
shown in the image here, you can also define the height and
thickness of this poly solid using command line options.
REGEN3
This command was introduced in AutoCAD 2017.1 update
and it is especially helpful in removing the 3D graphics-
related anomalies and surface tessellations.
65
DELOBJ
This system variable controls the behaviour or 2D curves
when 3D tools like Extrude, Presspull and Sweep are used.
You can change the value of this system variable so that

AutoCAD either retains or deletes curves after converting
them to 3D.
VOLUME
Using this command you can find the volume of a 3D solid as
well as lots of other information like its moment of inertia,
radius of gyration, centroid, and products of inertia.
INTERFERE
This command can be used to detect intersecting 3D solids.
The command is especially useful in situations where you
want to detect clashes between different solids like pipes
and walls.
66
XEDGES
You can extract the edges of a 3D solid as 2D geometries
using this tool. In the image shown here, the XEDGES tool
has been used to extract the edges of the 3D solid and then
the solid geometry has been moved to reveal the edges only.
SECTIONPLANE
Using this command you can create a section plane in the
drawing that can be used to see the 3D drawings by
sectioning them along different planes.
67
FLATSHOT
This command is great for converting a 3D drawing into 2D.
Using this command you can also create multiple views of a

single 3D drawing like the front, top and isometric on a
single plane.
PROJECTGEOMETRY
Using this command you can project a 2D curve on a 3D
surface, solid or region as shown in the animated image
below.
Here is an example shown in this image.
Shell (SOLIDEDIT)
Using this command you can convert a 3D solid into a hollow
solid with a wall thickness.
To use this command type SOLIDEDIT on the command line

press enter type B press enter again type S and press enter
again.
Alternatively, you can also select the shell tool from Solid
editing panel of the Solid tab.
HELIX
As the name suggests this command can be used to make a
helix in AutoCAD drawing.
68
SURFPATCH
Using this command you can fill the open areas of a surface
like the top of a cylinder as shown in this animated image
here.
Moveface (SOLIDEDIT)
Using this tool you can move faces like a groove of a 3D solid
from one point to other as shown in the animated image
here.
For using this tool type SOLIDEDIT on the command line

press enter then type F press enter then type M and press
enter again.
SURFTRIM
This command is similar to the trim command of 2D
drawings but in this case, it will trim surfaces instead of 2D
geometries.
FACETRES
This command adjusts the smoothness of shaded and
rendered objects and shadows. Its default value is 0.5000
and you can change it from 0.01 to 10.0.
The higher the value smoother will be the 3D objects but it

will consume more processing power to render it.
69
3DALIGN
Using this command you can align a 3D solid object with
respect to another 3D solid, this video explains the use of
this command in detail.
SURFOFFSET
Using this command you can offset any surface inside,
outside or on both sides of the surface as shown in the
animated image here.
IMPRINT
Using this command you can imprint 2D drawings on planar
faces of a 3D solid or a surface to create additional faces for
3D tools like Presspull.
SOLIDHIST
Using this tool you can record the history of solids on which
boolean operations are performed and you can modify
these solids later.
In the image, here Subtract operation is performed on two

solids and then the amount of removed part is changed by
selecting the Cone by pressing CTRL key and then changing
its base radius.
The default value of this system variable is 0 (off) but you can
activate it using value 1 (ON).
70
3DP
It prepares the watertight mesh object in AutoCAD and saves
it in STL format for 3D printing.
CAM
It helps the user to set up a camera (Perspective) view so
that the user can view the angle as if looking at it in the real
world.
UNI
This command merges two or more 3D objects connected
together into one.
SUBTRACT
This command subtracts one object from another 3D object
provided they have interfering volume.
IN
This tool creates a 2D region, surface or 3D solid from the
overlapping section.
71
Jaiprakash Pandey
Author
About this Book

This revised and updated edition of the AutoCAD
commands eBook is written by Jaiprakash Pandey with
inputs and suggestions from our team here at
SourceCAD Learning.
Special thanks to Alan Baker for suggesting some really

great improvements in the book. Thanks, Kalpana for
compiling all the commands into a beautiful eBook
format.
Though this edition is revised meticulously still not

immune to errors and if you find any please reach out
to me at admin@thesourcecad.com
This book is protected by copyright and its reprint or reuse in part or full is prohibited without
permission from the author.

200 AutoCAD Commands (3rd Edition)

Uploaded by

Copyright:

Available Formats

200 AutoCAD Commands (3rd Edition)

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

200 AutoCAD Commands (3rd Edition)

Uploaded by

Copyright:

Available Formats

What are some of the keyboard shortcuts mentioned in the document?

What are some of the keyboard shortcuts mentioned in the document?

What categories are the commands divided into?

What categories are the commands divided into?

2 0 0

The command list here focuses on usability

This book is great for a beginner as well as an

The commands are divided into different

O2 Status bar toggle

O3 Basic AutoCAD commands

O5 Performance related commands

Keyboard shortcuts or hotkeys are the shortest and

You can also use the PR command to open the property

You can use this to open a quick calculator inside the

If for some reason your command line is hidden from the

You can use this keyboard shortcut to make blocks quickly

The status bar is an important feature of the AutoCAD user

You can also toggle between different isoplanes using F5

You change the value of this system variable to 1 to make

When the value of this system variable is set to 2, an

If you set the value of this system variable to 1, only the

You can also use 3DCONFIG for opening the graphics

These are some of the Draw and Modify commands which

Check this animated image for an example.

Following image shows an example of spline.

Mtext Is also associated with a text editor dialogue box where

These are some of the commands which can be frequently

You can start this subcommand by entering ‘CAL (don’t forget

After deleting an object if you made many other changes in

Check this animated image for an example.

It is helpful if you want to break a curve at the point of

Check this animated image for an example.

Using this command you can find a lot of information about

As an example, you can use quick select to make a selection

To use this command simply type LIST on the command line

To access this command you can use DIM command or select

To use this command type SCALETEXT on the command line

This is especially helpful in the situation where you want to

By default, AutoCAD takes origin as the base point which can

This command can be used to quickly find the location of

I have made a simple table by importing blocks of design

In image A below the text is oriented at different angles and in

Whereas in image B below TORIENT command has been used

This boundary can be used to find the area of the enclosed

In the image below the boundary of the area mentioned as A

Type BREAKLINE on the command line and press enter then

There are several inbuilt tools and commands in AutoCAD

By turning the FILLMODE to off you can enhance the

You need to regenerate the drawing using REA command

You can remove this preview thereby improving the

This system variable also affects the file size of AutoCAD

By decreasing the value of this system variable you can

When you increase the value of this system variable opposite

The default value of this aperture is 10 but depending on the

The size of the aperture is relative to the current scale of the

By default the value of this system variable is 1 which allows

The default value of this system variable is 1 which allows the

When you, however, change the value of this system variable

In the image shown below Wipeout command has been used

You can use the WIPEOUTFRAME system variable and change