This document outlines an assignment for a Building Technology course to illustrate cast-in-place and pre-cast construction systems. Students must submit drawings of two floor/roof systems and two wall panel systems, showing connections, materials, and each item's purpose. Drawings must be inked on A3 paper and will be evaluated based on completeness, clarity, visual quality, technical details, and overall presentation. Students must compile their drawings and include a cover sheet with their name and other details. Submissions are due within 10 days between September 26-30, with no extensions allowed.
This document outlines an assignment for a Building Technology course to illustrate cast-in-place and pre-cast construction systems. Students must submit drawings of two floor/roof systems and two wall panel systems, showing connections, materials, and each item's purpose. Drawings must be inked on A3 paper and will be evaluated based on completeness, clarity, visual quality, technical details, and overall presentation. Students must compile their drawings and include a cover sheet with their name and other details. Submissions are due within 10 days between September 26-30, with no extensions allowed.
This document outlines an assignment for a Building Technology course to illustrate cast-in-place and pre-cast construction systems. Students must submit drawings of two floor/roof systems and two wall panel systems, showing connections, materials, and each item's purpose. Drawings must be inked on A3 paper and will be evaluated based on completeness, clarity, visual quality, technical details, and overall presentation. Students must compile their drawings and include a cover sheet with their name and other details. Submissions are due within 10 days between September 26-30, with no extensions allowed.
This document outlines an assignment for a Building Technology course to illustrate cast-in-place and pre-cast construction systems. Students must submit drawings of two floor/roof systems and two wall panel systems, showing connections, materials, and each item's purpose. Drawings must be inked on A3 paper and will be evaluated based on completeness, clarity, visual quality, technical details, and overall presentation. Students must compile their drawings and include a cover sheet with their name and other details. Submissions are due within 10 days between September 26-30, with no extensions allowed.
College of Engineering and Architecture Department of Architecture A.Y. 2022 – 2023 _ 1st Semester
BTECH 413 ACTIVITY/PROJECT NO.1
Building Technology 5 Cast-in-place and Pre-Cast Alternative Building Construction System Instructor: 3rd Week of September 2022 Teodoro L. Luzung , UAP to 5th Week of September 2022 tlluzung@dhvsu.edu.ph
A. Project Title / Subtitle
“Cast-in-place and Pre-cast Construction System”
B. Topic Description/ Brief
Cast-in-place concrete, also known as “site-cast” or “poured-in-place” concrete, is poured and cured onsite in the concrete’s finished position. For specific applications, this type of casting can be ideal. For example, some foundations and other very large concrete components would be difficult to transport between a concrete plant and job site, making cast-in-place concrete more feasible. Cast-in-place concrete is also commonly used for small projects. Precast concrete pricing scales with projects, so smaller projects can cost more. In these cases, cast-in-place concrete may be preferred. But overall, precast concrete is the best choice for building foundations with structural integrity and dimensions built to your precise specifications.
Precast concrete, sometimes called “prefabricated” or “pre-made” concrete, is a concrete product that is created offsite, then delivered to its project destination for final use. Precast concrete products are created by pouring a cement mixture into a mold that can contain wire mesh, rebar, or even prestressed cable. The filled mold is then cured in a controlled environment to ensure greater control over material quality.
C. Project Requirements Students are required to submit illustrations showing the different parts of the specific construction system that should reflect the connections, the materials that were used, and the purpose of each item that are mentioned below. The outputs should be INKED and rendering of the drawings is optional but rendered outputs will have additional points.
TOPIC: CAST-IN-PLACE AND PRE-CAST CONSTRUCTION SYSTEMS
• FLOOR SYSTEM AND ROOF SLAB SYSTEM (PICK 2)
o FLAT SLAB o FLAT PLATE o RIBBED FLOOR SLAB o WAFFLE SLAB o LIFT SLAB o SPAN STRESS FLOOR SYSTEM o SLIP FORM METHOD
• WALL PANEL SYSTEMS (PICK 2)
o FLAT TYPE o RIBBED TYPE o WINDOW TYPE o WALL TYPE o TILT-UP WALL PANEL SYSTEM
Remarks: [1] Each item shall be drawn on an A3 paper (Example is provided on the last page) [2] All drawings, details, and specifications should be INKED [3] Rendering of the outputs are not required, but may have additional points if provided
Project Goals and Objectives
• To explore the variety of materials and tools in an actual building/construction
• To introduce the details of cast-in-place and pre-cast type of construction • To understand better the advantages of using such systems.
Page 1 of 3 BTECH 2413_ACTIVITY/PROJECT NO.1_1st Semester-A.Y. 2022-2023 D. Project Criteria / Presentation
A. PROVISION OF COMPLETE NUMBER OF OUTPUTS (4 A3) -10 PTS.
B. CLEANLINESS OF THE SUBMITTAL -15 PTS. C. VISUAL APPEAL OF THE PRESENTATION MATERIAL -20 PTS. D. PROVISION OF THE IMPORTANT DETAILS -25 PTS. E. OVERALL PRESENTATION OF THE PROJECT -30 PTS.
E. Notes for submission
• After finishing your outputs, compile them all together and include 1 A3 paper that will serve as your top sheet. It shall include the following details on the LOWER RIGHT CORNER of the sheet:
• All outputs shall be submitted on the face-to-face day that will be announced by the respective course instructor.
F. Project timeline
❖ LAUNCHING DATE: September 12-16, 2022
❖ SUBMISSION DATE & TIME: September 26-30, 2022 on or before 12 noon ❖ DURATION: 10 DAYS
NOTE(s): • “NO EXTENSION OF SUBMISSION DATE” – for strict compliance [A.1] • The deadline for the said plate/activity/assignment is stated ABOVE, late submittals are subject to grade deduction depending on the delay of submission. – for strict compliance. [A.1] • Also, non-compliance with the stated requirements will be subject to grade deductions. [A.1]
Remarks: [A.1] (depending on Instructor’s directions)
PREPARED BY:
AR. TEODORO L. LUZUNG, UAP
BTECH 413 Instructor | Ar Department
Page 2 of 3 BTECH 2413_ACTIVITY/PROJECT NO.1_1st Semester-A.Y. 2022-2023 Page 3 of 3 BTECH 2413_ACTIVITY/PROJECT NO.1_1st Semester-A.Y. 2022-2023
