XC9128 XC9129

XC9128/XC9129 series is Discontinued.
XC9128/XC9129 Series
ETR0411-013
1A Driver Transistor Built-In, Step-Up DC/DC Converters
☆Green Operation Compatible
■GENERAL DESCRIPTION
The XC9128/XC9129 series are synchronous step-up DC/DC converters with a 0.2Ω (TYP.) N-channel driver transistor and
a synchronous 0.2Ω (TYP.) P-channel switching transistor built-in. A highly efficient and stable current can be supplied up to
1.0A by reducing ON resistance of the built-in transistors.
With a high switching frequency of 1.2MHz, a small inductor is selectable making the series ideally suited for applications
requiring low profile or space saving solutions. With the MODE pin, the series provides mode selection of PWM control or
PFM/PWM automatic switching control. In the PWM/PFM automatic switching mode, the series switches from PWM to PFM
to reduce switching loss when load current is small. When load current is large, the series switches automatically to the PWM
mode so that high efficiency is achievable over a wide range of load conditions. The series also provides small output ripple
from light to large loads by using the built-in circuit which enables the smooth transition between PWM and PFM.
With a adaptor enable function of the XC9128 series, when a voltage higher than the input voltage is applied to the output,
the input and the output become isolated making it possible for the IC to work in parallel with the likes of an AC adaptor.
■APPLICATIONS ■ FEATURES
●Digital audio equipment High Efficiency, Large Current Step-Up Converter
●Digital still cameras / Camcorders : 150mA＠VOUT=3.3V, VIN=0.9V
Output Current
500mA＠VOUT=3.3V, VIN=1.8V
●Computer Mouses Input Voltage Range : 0.8V ~ 6.0V
●Multi-function power supplies : 1.8V ~ 5.3V (Externally set)
Output Voltage Setting Set up freely with a reference voltage
Range supply of 0.45V (±0.010V) & external
components
: 1.2MHz
Oscillation Frequency
(Fixed oscillation frequency accuracy ±15%)
Input Current : 1.0A
Maximum Current Limit
: 1.2A (MIN.), 2.0A (MAX.)
: PWM, PWM/PFM control
Control
externally selectable
High Speed :100mV @ VOUT=3.3V,
Transient Response VIN=1.8V, IOUT=10mA→100mA
: Thermal shutdown
Protection Circuits
Integral latch method (Over current limit)
Soft-Start Time : 5ms (TYP.) internally set
Ceramic Capacitor Compatible
Adaptor Enable Function (XC9128 series)
Flag Output (XC9128 series) : Open-drain output
Operating Ambient Temperature : - 40 ~ 85℃
Packages : MSOP-10, USP-10B
Environmentally Friendly : EU RoHS Compliant, Pb Free
■TYPICAL APPLICATION CIRCUIT ■TYPICAL PERFORMANCE

CHARACTERISTICS
●Efficiency vs. Output Current
XC9128B45CD
L=4.7μH(LTF5022-LC),CL =30μF(LMK212BJ106KG ×3)
VOUT=3.3V,VEN=6V,VFO =OPEN,VAEN/ =0V
RFB1 =270kΩ,RFB2 =43kΩ,CFB=12pF,CIN=10μF
CIN VOUT 100
PGND VOUT
1 10 90
VIN MODE
2 Lx MODE 9 CFB RFB1 80
Efficiency: EFFI (%)
L CL
3 BAT FB 8 (ceramic) 70
60 1.8V 3.0V
EN AGND
4 EN 7
FO RFB2 50
5 FO AEN/ 6
40
30
20
PWM/PFM (VMODE=0V)
10
PWM (VMODE=VOUT)
0
0.1 1 10 100 1000
Output Current: I OUT (mA)
1/28
XC9128/XC9129 series
XC9128/XC9129 Series is Discontinued.
■BLOCK DIAGRAM
●XC9128 Series
AGND VOUT
Phase Current Sense,
Compensation Limit, PFM
Error Amp. PWM
comparator
FB Lx
PWM/PFM Buffer
Controller, Logic Driver
PGND
Vref with RAMP Wave
AEN/ OSC
Soft Start Generator
MODE MODE
EN,
EN
Thermal Shutdown
Current Limit, FO
Thermal,
Soft Start,
BAT
EN
●XC9129 Series
The XC9129 series does not have AEN/ pin and FO pin.
2/28
XC9128/XC9129 series is Discontinued. XC9128/XC9129
Series
■PRODUCT CLASSIFICATION
●Ordering Information
XC9128①②③④⑤⑥-⑦ (*1)
・・・・Adaptor Chip Enable Pin and Flag Output Pin are added
DESIGNATOR ITEM SYMBOL DESCRIPTION

B With integral protection
① Integral Protection
D Without integral protection
Fixed reference voltage 0.45Ｖ
②③ Reference Voltage 45
②=4, ③=5
④ Oscillation Frequency C 1.2MHz
AR MSOP-10 (1,000pcs/Reel)
Packages AR-G MSOP-10 (1,000pcs/Reel)
⑤⑥-⑦(*1)
(Order Unit) DR USP-10B (3,000pcs/Reel)
DR-G USP-10B (3,000pcs/Reel)
XC9129①②③④⑤⑥-⑦ (*1)
・・・・Adaptor Chip Enable Pin and Flag Output Pin are not added
DESIGNATOR ITEM SYMBOL DESCRIPTION

① Integral Protection D Without integral protection
Fixed reference voltage 0.45Ｖ
②③ Reference Voltage 45
②=4, ③=5
④ Oscillation Frequency C 1.2MHz
Package DR USP-10B (3,000pcs/Reel)
⑤⑥-⑦(*1)
(Order Unit) DR-G USP-10B (3,000pcs/Reel)
(*1)
The “-G” suffix denotes Halogen and Antimony free as well as being fully EU RoHS compliant.
3/28
■PIN CONFIGURATION
FO 5 5
FO 6 6 AEN/
AEN/
EN 4 4
EN 7 7 AGND
AGND
PGND 1 10 VOUT BAT 8 8 FB
BAT 3 3
PGND　1 10　VOUT
FB
Lx 2Lx　2 9 MODE
9　MODE
Lx 2 2
Lx 9 9 MODE
MODE
BAT 3
BAT　3 8　FB
8 FB
PGND 1 1
PGND 1010VOUT
VOUT
EN EN　4
4 7　AGND
7 AGND
FO FO　5
5 6 AEN/
6　AEN/
USP-10B
USP-10B
( BOTTOM VIEW )
(BOTTOM VIEW)
MSOP-10 XC9128 Series
MSOP-10
(TOP VIEW)
(　TOP　VIEW　)
NC 5 5
FO 6 6 AEN/
NC
EN 4 4
EN 7 7 AGND
AGND
BAT
BAT 3
3 8 8 FB
FB
Lx 2 2
Lx 9 9 MODE
MODE
PGND 1 1
PGND 1010VOUT
VOUT
USP-10B
USP-10B
( BOTTOM VIEW )
(BOTTOM VIEW)
XC9129 Series
■PIN ASSIGNMENT
PIN NUMBER
USP-10B* USP-10B* PIN NAME FUNCTION
MSOP-10*
(XC9128) (XC9129)
1 1 1 PGND Power Ground
2 2 2 Lx Output of Internal Power Switch
3 3 3 BAT Battery Input
4 4 4 EN Chip Enable
5 5 - FO Flag Output
6 6 - AEN/ Adaptor Enable
7 7 7 AGND Analog Ground
8 8 8 FB Output Voltage Monitor
9 9 9 MODE Mode Switch
10 10 10 VOUT Output Voltage
- - 5, 6 NC No Connection
* For MSOP-10 and USP-10B packages, please short the GND pins (pins 1 and 7).
* The dissipation pad for the USP-10B package should be solder-plated following the recommended mount pattern and metal masking
so as to enhance mounting strength and heat release. If the pad needs to be connected to other pins, it should be connected to the
Ground pins (pins 1 and 7).
4/28
Series
■FUNCTION CHART
1. EN, AEN/ Pin Function
●XC9128 Series
EN PIN AEN/ PIN FB PIN VOLTAGE IC OPERATIONAL STATE SOFT-START FUNCTION
L→H L - Operation Available
H H→L Lower than 0.45×0.8V Operation Available
Higher than
H H→L Operation Not Available
0.45×0.95V
Step-Up Operation Shut-
H H - -
Down
L L - Disable -
L H - Disable -
* Do not leave the EN and AEN/ Pins open.
●XC9129 Series
EN PIN IC OPERATIONAL STATE
H Operation
L Disable
* Do not leave the EN Pin open.
2. MODE Pin Function

●XC9128/XC9129 Series
MODE PIN FUNCTION
H PWM Control
L PWM/PFM Automatic Switching Control
* Do not leave the MODE Pin open.
5/28
■ABSOLUTE MAXIMUM RATINGS
PARAMETER SYMBOL RATINGS UNITS

VOUT Pin Voltage VOUT -0.3 ~ 6.5 V
AEN/ Pin Voltage (*2) VAEN/ -0.3 ~ 6.5 V
FO Pin Voltage (*2) VFO -0.3 ~ 6.5 V
FO Pin Current (*2) IFO 10 mA
FB Pin Voltage VFB -0.3 ~ 6.5 V
BAT Pin Voltage VBAT -0.3 ~ 6.5 V
MODE Pin Voltage VMODE -0.3 ~ 6.5 V
EN Pin Voltage VEN -0.3 ~ 6.5 V
LX Pin Voltage VLx -0.3 ~ VOUT + 0.3 V
LX Pin Current ILx 2000 mA
350
MSOP-10
Power Dissipation 500 (40mm x 40mm Standard board) (*1)
Pd mW
(Ta=25℃) 150
USP-10B
500 (40mm x 40mm Standard board) (*1)
Operating Ambient Temperature Topr -40 ~ 85 ℃
Storage Temperature Tstg -55 ~ 125 ℃
AGND, PGND is the standard voltage for all of voltages.
(*1)
This power dissipation figure shown is PCB mounted and is for reference only.
The mounting condition is please refer to PACKAGING INFORMATION.
(*２)
The XC9129 series does not have AEN/ pin and FO pin. These pins are available only in the XC9128 series.
6/28
Series
■ELECTRICAL CHARACTERISTICS
XC9128/XC9129 Series Ta=25℃
PARAMETER SYMBOL CONDITIONS MIN. TYP. MAX. UNITS CIRCUIT
Input Voltage VIN - - - 6.0 V -
VOUT=VIN=3.3V, VFO=0V (*8)
FB Voltage VFB Voltage to start oscillation during 0.44 0.45 0.46 V ④
VFB= 0.46V → 0.44V
Output Voltage Setting Range VOUTSET - 1.8 - 5.3 V ①
Connect to external components,
- - 0.8 V ①
RL=1kΩ
Operation Start Voltage VST1
- - 0.9 (*1) V ①
RL=33Ω
Voltage to start oscillation during
Oscillation Start Voltage VST2 - 0.8 - V ①
VIN=0V → 1V, RL=1kΩ
Operation Hold Voltage VHLD Connect to external components, RL=1kΩ - 0.7 - V ①
Supply Current 1 IDD1 VIN = VOUT =3.3V, VFB=0.45V×0.9 - 3 6 mA ②
Supply Current 2 (XC9128) VIN = VOUT =3.3V - 30 80
IDD2 VFB=0.45V×1.1 (Oscillation stop), μA ②
Supply Current 2 (XC9129) VMODE=0V - 28 78
Input Pin Current IBAT VIN =3.3V, VOUT =1.8V, VEN=0V - 2 10 μA ③
Stand-by Current ISTB VIN = VOUT =3.3V, VEN=0V - 2 10 μA ②
VIN = VOUT =3.3V, VFO=0V (*8),
Oscillation Frequency fOSC 1.02 1.20 1.38 MHz ④
VFB=0.45V×0.9
Maximum Duty Cycle MAXDTY 85 92 96 % ④
VFB=0.45V×0.9
Minimum Duty Cycle MINDTY - - 0 % ④
VFB=0.45V×1.1
PFM Switching Current IPFM - 250 400 mA ①
VMODE=0V, RL=330Ω
Efficiency (*2) EFFI - 93 - % ①
RL=33Ω
VIN=VLx=VOUT+50mV,
LX SW "Pch" ON Resistance RLxP - 0.20 0.35 (*1) Ω ⑤
VFB=0.45V×1.1 (*3)
LX SW "Nch" ON Resistance RLxN VIN=VOUT=3.3V, Lx =50mV (*4) - 0.20 (*1) 0.35 (*1) Ω ⑦
LX Leak Current ILXL VIN=VOUT= VLX, VFB=0V - 1 - μA ⑤

Current Limit (*5) ILIM VOUT>2.5V 1.2 1.5 2.0 A ①
Time to stop oscillation during
Integral Latch Time (XC9128) (*6)
RL=33Ω → 3.3Ω, VFO=L → H
tLAT - 3.5 - ms ①
Time to stop oscillation during
Integral Latch Time (XC9129) (*6)
RL=33Ω → 3.3Ω
Time to start oscillation during VEN=0V
Soft-Start Time 1 tSS1 → VIN at VIN = VOUT =3.3V, VFO=0V, 1.7 5.3 10.5 ms ④
VFB=0.45V×0.95
VIN = VOUT =3.3V, VFO=0V,
VFB=0.45V×0.95
Soft-Start Time 2 (*7) tSS2 - 0.02 0.04 ms ④
Time to start oscillation during
VAEN/=VIN→0V.
VIN = VOUT =3.3V, VFO=0V,
VFB=0.45V×0.8
Soft-Start Time 3 (*7) tSS3 1.7 5.3 10.5 ms ④
Time to start oscillation during
VAEN/=VIN→0V
Thermal Shutdown
TTSD - - 150 - ℃ -
Temperature
Hysteresis Width THYS - - 20 - ℃ -
VIN =3.3V
Output Voltage Drop
VLVP Voltage to stop oscillation during 1.3 1.48 1.56 V ⑥
Protection (*6)
VOUT=1.56V→1.3V
FO Output Current (*7) IFO_OUT VIN =VOUT=3.3V, VFO=0.25V 1.3 1.7 2.2 mA ④
FO Leakage Current (*7) IFO_Leak VIN = VOUT =3.3V, VEN=0V ,VFO=1V - 0 1 μA ④
7/28
■ELECTRICAL CHARACTERISTICS (Continued)

●XC9128/XC9129 Series (Continued) Ta=25℃
PARAMETER SYMBOL CONDITIONS MIN. TYP. MAX UNIT CIRCUIT
S
VIN =VOUT=3.3V, VFO=0V (*8)
EN "H" Voltage VENH Voltage to start oscillation during 0.65 - 6.0 V ④
VFB=0.45V×0.9, VEN= 0.2V→0.65V
VIN = VOUT =3.3V, VFO=0V (*8)
Voltage to stop oscillation during
EN "L" Voltage VENL AGND - 0.2 V ④
VFB=0.45V×0.9,
VEN= 0.65V→0.20V
MODE "H" Voltage VMODEH RL =330Ω, Voltage operates at PWM control 0.65 - 6.0 V ①
MODE "L" Voltage VMODEL RL =330Ω, Voltage operates at PFM control AGND - 0.2 V ①
VIN = VOUT =3.3V, VFO=0V
AEN/ Voltage (*7) VAEN/ 0.7 0.8 0.9 V ④
Voltage to start oscillation during VAEN/= 0.9V→0.7V
EN "H" Current IENH VIN=VOUT=VFB=VEN=6.0V - - 0.1 μA ②
EN "L" Current IENL VIN=VOUT=VFB=6.0V, VEN=0V -0.1 - - μA ②
MODE "H" Current IMODEH VIN=VOUT=VFB=VMODE=6.0V - - 0.1 μA ②
MODE "L" Current IMODEL VIN=VOUT=VFB=6.0V, VMODE=0V -0.1 - - μA ②
AEN/ "H" Current (*7) IAEN/H VIN=VOUT=VFB=VAEN/=6.0V - - 0.1 μA ②
AEN/ "L" Current (*7) IAEN/L VIN=VOUT=6.0V, VEN=0V, VAEN/=0V -0.1 - - μA ②
FB "H" Current IFBH VIN=VOUT=VFB=6.0V - - 0.1 μA ②
FB "L" Current IFBL VIN=VOUT=6.0V, VFB=0V -0.1 - - μA ②

Test Conditions: For the Circuit No.1, unless otherwise stated, VIN=1.8V, VEN=VMODE=VFO=3.3V, VAEN/=0V （*8）
For the Circuit No.2, unless otherwise stated, VIN=1.8V, VFB =0V, VEN=VMODE=3.3V, VAEN/=0V （*8）
For the Circuit No.3, unless otherwise stated, VIN=1.8V, VOUT=VEN=VMODE=3.3V, FB=0V
For the Circuit No.4, unless otherwise stated, VIN=1.8V, VFB=0V, VEN=VMODE=Vpull=VFO=3.3V, VAEN/ =0V （*8）
For the Circuit No.5, unless otherwise stated, VIN=3.3V, VAEN/=0V （*8）
For the Circuit No.6, unless otherwise stated, VEN=VMODE=Vpull=VFO=3.3V, VFB=0V （*8）
For the Circuit No.7, unless otherwise stated, VEN=VMODE=3.3V

External Components: For the Circuit No.1, RFB1=270kΩ, RFB2=43kΩ, CFB=12pF, L=4.7μH(LTF5022 TDK), CL1=22μF(ceramic),
CL2=10μF(ceramic), CIN=10μF(ceramic)
For the Circuit No.2,3, CIN=1μF(ceramic)
For the Circuit No.4,6, CIN=1μF(ceramic), Rpull=300Ω
For the Circuit No.5, CIN=1μF(ceramic), COUT=1μF(ceramic)
For the Circuit No.7, CIN=1μF(ceramic), COUT=1μF(ceramic), SBD =XBS304S17(TOREX), Rpull=0.5Ω
1 : Designed value
*
2 : Efficiency ={(output voltage) X (output current)} ÷ {(input voltage) X (input current)} X 100
*
3 : LX SW "Pch" ON resistance=(VLx-VOUT pin test voltage)÷100mA

*
4 : Testing method of LX SW "Nch" ON resistance is stated at test circuits.

*
5 : Current flowing through the Nch driver transistor is limited.

*
6 : The XC9128D/XC9129D type does not have integral latch protection and VLVP function.
*
This is only available with the XC9128B type.

7 : The XC9129 series does not have FO and AEN/ pins. These pins are only available in the XC9128 series.
*
8 : The XC9129 series does not have FO and AEN/ pins. The AEN/FO functions are only effective for the test of the XC9128 series.
*
8/28
Series
■TYPICAL APPLICATION CIRCUIT

CL1
CIN VOUT
1 PGND VOUT 10
VIN
2 Lx MODE 9 CL2 CFB RFB1
L MODE
3 BAT FB 8
EN AGND
4 EN 7
FO RFB2
5 FO AEN/ 6
<Output Voltage Setting>

Output voltage can be set by adding external split resistors. Output voltage is determined by the following equation,
based on the values of RFB1 and RFB2. The sum of RFB1 and RFB2 should normally be 500kΩ or less.
VOUT=0.45 × (RFB1 + RFB2) / RFB2
The value of CFB, speed-up capacitor for phase compensation, should be fZFB = 1 / (2 x π x CFB1 x RFB1) which is in
the range of 10 kHz to 60 kHz. Adjustments are depending on application, inductance (L), load capacitance (CL) and
dropout voltage.
[Example of calculation]
When RFB1=270kΩ, RFB2=43kΩ,
VOUT1 = 0.45 × (270k+43k ) / 43k = 3.276V
VOUT (V) RFB1 (kΩ) RFB2 (kΩ) CFB (pF)

1.8 300 100 10
2.5 270 59 12
3.3 270 43 12
5.0 180 17.8 15
[External Components]
1.2MHz:
L : 4.7μH (LTF5022-4R7-LC TDK)
: 4.7μH (CDRH4D28C-4R7N SUMIDA)
CL1 : 22μF (ceramic)
CL2 : 10μF (ceramic)
CIN : 10μF (ceramic)
* CL1 should be selected in 10μF or higher.

Capacitance CL1 + CL2 is recommended 30μF or higher. (Ceramic capacitor compatible)
If CL1 is lower than 10μF, operation may be unstable.
In case of the usage CL1 + CL2 ＜30μF, output ripple may increase so that we recommend that you fully check
actual performance on the board.
* If using Tantalum or Electrolytic capacitors please be aware that ripple voltage will be higher due to the larger
ESR (Equivalent Series Resistance) values of those types of capacitors. Please also note that the IC’s
operation may become unstable with such capacitors so we recommend that you fully check actual
performance.
9/28
■OPERATIONAL EXPLANATION
The XC9128/XC9129 series consists of a reference voltage source, ramp wave circuit, error amplifier, PWM comparator,
phase compensation circuit, N-channel driver transistor, P-channel synchronous rectification switching transistor and current
limiter circuit. The error amplifier compares the internal reference voltage with the FB pin feed back voltage via resistors RFB1
and RFB2. Phase compensation is performed on the resulting error amplifier output, to input a signal to the PWM comparator
to determine the turn-on time of the N-channel driver transistor during PWM operation. The PWM comparator compares, in
terms of voltage level, the signal from the error amplifier with the ramp wave from the ramp wave circuit, and delivers the
resulting output to the buffer driver circuit to cause the Lx pin to output a switching duty cycle. This process is continuously
performed to ensure stable output voltage. The current feedback circuit monitors the N-channel driver transistor’s turn-on
current for each switching operation, and modulates the error amplifier output signal to provide multiple feedback signals.
This enables a stable feedback loop even when a low ESR capacitor, such as a ceramic capacitor, is used, ensuring stable
output voltage.
<Reference Voltage Source>

The source provides the reference voltage to ensure stable output of the DC/DC converter.
<Ramp Wave Circuit>

The ramp wave circuit determines switching frequency. The frequency is fixed internally at 1.2MHz. The Clock generated is
used to produce ramp waveforms needed for PWM operation, and to synchronize all the internal circuits.
<Error Amplifier>
The error amplifier is designed to monitor output voltage. The amplifier compares the reference voltage with the feedback
voltage divided by the internal resistors (RFB1 and RFB2). When the FB pin is lower than the reference voltage, output voltage
of the error amplifier increases. The gain and frequency characteristics of the error amplifier are optimized internally.
< Maximum Current Limit>

The current limiter circuit monitors the maximum current flowing through the N-channel driver transistor connected to the Lx
pin, and features a combination of the current limit and latch function.
When the driver current is greater than a specific level (equivalent to peak coil current), the maximum current limit
function starts to operate and the pulses from the Lx pin turn off the N-channel driver transistor at any given time.
When the driver transistor is turned off, the limiter circuit is then released from the maximum current limit detection state.
At the next pulse, the driver transistor is turned on. However, the transistor is immediately turned off in the case of an
over current state.
 When the over current state is eliminated, the IC resumes its normal operation.
The XC9128B type waits for the over current state to end by repeating the steps  through . If an over current state continues
for several ms and the above three steps are repeatedly performed, the IC performs the function of latching the OFF state of the
N-channel driver transistor, and goes into operation suspension mode. After being put into suspension mode, the IC can resume
operation by turning itself off once and then re-starting via the EN pin, or by restoring power to the V IN pin.
The XC9128D/XC9129D type does not have this latch function, so operation steps  through  repeat until the over current
state ends.
Integral latch time may be released from a over current detection state because of the noise. Depending on the state of a
substrate, it may result in the case where the latch time may become longer or the operation may not be latched. Please locate
an input capacitor as close as possible.
Limit<# ms
Limit<# mS
Limit<# ms
Limit># mS
Current Limit LEVEL
IOUT
0mA
VOUT
VSS
LX
CE
Restart
VIN
10/28
Series
■OPERATIONAL EXPLANATION (Continued)

<Thermal Shutdown>
For protection against heat damage, the thermal shutdown function monitors chip temperature. When the chip’s
temperature reaches 150℃ (TYP.), the thermal shutdown circuit starts operating and the driver transistor will be turned off.
At the same time, the output voltage decreases. When the temperature drops to 130℃ (TYP.) after shutting off the current
flow, the IC performs the soft start function to initiate output startup operation.
<MODE>
The MODE pin operates in PWM mode by applying a high level voltage and in PFM/PWM automatic switching mode by applying
a low level voltage.
<Shut-Down>
The IC enters chip disable state by applying low level voltage to the EN pin. At this time, the Pch synchronous switching
transistor turns on when VIN>VOUT and vise versa the transistor turns off when VIN<VOUT.
<Adaptor Enable>
While the XC9128 series using step-up DC/DC converters in parallel with an added power source such as AC adaptors, the
circuit needs the step-up DC/DC converter to be transient-efficient for sustaining output voltage in case the added power source
runs down. The AEN/ pin voltage determines whether the added power source is supplied or not so that high-speed following
operation is possible.
The IC starts operating although the driver transistor is off when a high level voltage is applied to the AEN/ pin after a high level
voltage is also applied to the EN pin. If the AEN/ pin voltage changes from high level to low level while the EN pin sustains a
high level voltage, the step-up operation starts with high-speed following mode (without soft-start).
The XC9129 series does not have adaptor enable function.
<Error Flag >

For the XC9128 series, the FO pin becomes high impedance during over current state, over temperature state, soft-start period,
and shut-down period.
The XC9129 series does not have flag out function.
11/28
■NOTE ON USE
1. Please do not exceed the stated absolute maximum ratings values.
2. The DC/DC converter / controller IC's performance is greatly influenced by not only the ICs' characteristics, but also by those
of the external components. Care must be taken when selecting the external components.
3. Make sure that the PCB GND traces are as thick as possible, as variations in ground potential caused by high ground
currents at the time of switching may result in instability of the IC.
4. Please mount each external component as close to the IC as possible and use thick, short traces to reduce the circuit
impedance.
5. When the device is used in high step-up ratio, the current limit function may not work during excessive load current. In this
case, the maximum duty cycle limits maximum current.
6. When the adaptor enable function is used in the below circuit, please use a diode with low reverse bias current. The sum of
RAEN1’s and RAEN2’s resistance should be set to manage the reverse bias current.
Ｄ
USB,
AC Adapter
CIN VOUT
1 PGND VOUT 10
VIN
2 Lx MODE 9 RFB1
L MODE CFB CL
3 BAT FB 8 (ceramic)
EN AGND
4 EN 7 RAEN1
FO RFB2
5 FO AEN/ 6
RAEN2
12/28
Series
■NOTE ON USE (Continued)

7. Pch synchronous switching transistor operation
The parasitic diode of the Pch synchronous transistor is placed between Lx (anode) and VOUT (cathode), so that the power
line can not be turned off from Lx to VOUT. On the other hand, the power line switch from VOUT to Lx is shown in the table
below.
●XC9128 Series
EN Pin AEN/Pin P-channel Synchronous Switch Transistor Operation
H H OFF
H L Switching
L H OFF
L L Undefined
●XC9129 Series
EN Pin P-channel Synchronous Switch Transistor Operation
H Switching
L Undefined
With the XC9128B type, when step-up operation stops as a result of the latch condition working when the maximum current
limit level is reached, the synchronous P-channel transistor will remain ON.
8. The maximum current limiter controls the limit of the N-channel driver transistor by monitoring current flow. This function
does not limit the current flow of the P-channel synchronous transistor.
9. The integral latch time of the XC9128B type, could be released from the maximum current detection state as a result of
board mounting conditions. This may extend integral latch time or the level required for latch operation to function may
not be reached. Please connect the output capacitor as close to the IC as possible.
10. With the XC9128B type, when the EN pin is left open or applied in the range of 0.2V ~ 0.65V, the integral latch or the VLVP
may not be able to release. Please make sure that the EN pin voltage is less than 0.2V or more than 0.65V, or use the
XC9128D type, which does not have the integral latch and the LVP functions.
11. With the XC9128B type, please make the VOUT pin voltage become more than 1.5V within the soft-start time, otherwise
the VLVP is detected. Also, the operation may become unstable, please test and verify the operation in the actual circuits
thoroughly before use.
12. When used in small step-up ratios, the device may skip pulses during PWM control mode.
13/28
■TEST CIRCUITS *1
< Circuit No.1 >
Wave Form Measure Point
L
Lx VOUT
CFB A
BAT MODE RFB1
A ※ External Components
CL1
CIN EN FB RL V
VIN CL2 L : 4.7uH(LTF5022T-4R7N2R0 : TDK)
V VEN VMODE CIN : 10uF (ceramic)
10kΩ
FO AEN/ V RFB2 CL1 : 22uF (ceramic)
VAEN/ CL2 : 10uF (ceramic)
VFO
PGND AGND
< Circuit No.2 > < Circuit No.3 >
Lx VOUT Lx VOUT
A BAT MODE A A BAT MODE
A EN FB A VMODE EN FB VOUT
CIN CIN
VIN FB VIN VMODE
FO AEN/ A FO AEN/
VEN VAEN/ VEN VFB
PGND AGND PGND AGND
※ External Components CIN : 1uF (ceramic) ※ External Components CIN : 1uF (ceramic)
< Circuit No.4 > <Circuit No.5 >

Rpull
Lx VOUT Lx VOUT
Vpull
A BAT MODE BAT MODE
A
VMODE VOUT
VIN CIN EN FB EN FB COUT
CIN
VEN FB VLx VFB
VAEN/
A FO AEN/ FO AEN/
VFO VAEN/ VIN
PGND AGND PGND AGND
Rpull : 300Ω COUT : 1uF (ceramic)
<Circuit No.6 > <Circuit No.7 >

Wave Form Measure Point Wave Form Measure Point
Rpull
Lx VOUT Lx VOUT
V1
SBD Rpull
Vpull
A BAT MODE BAT MODE
Vpull
VIN EN FB VOUT CLX EN FB
CIN CIN
V
VMODE COUT
VEN VIN VOUT
A FO AEN/ FO AEN/
VFO FB VEN VMODE
PGND AGND PGND AGND
Rpull : 300Ω COUT : 1uF (ceramic)
SBD : XBS304S17(TOREX)
Rpull : 0.5Ω
Measurement method for ON resistance of the Lx switch

Using the layout of circuit No.7 above, set the LX pin voltage to 50mV by adjusting the Vpull voltage whilst the Nch driver
transistor is turned on. Then, measure the voltage difference between both ends of Rpull. ON Resistance is calculated by using
the following formula:
RLXN=0.05 ÷ ((V1 – 0.05) ÷ 0.5)
where V1 is a voltage between SBD and Rpull. LX pin voltage and V1 are measured by an oscilloscope.
*1: The XC9129 series does not have the AEN/ pin and the FO pin. When the XC9129 series is measured, the FO and AEN pins
are not effective in the above mentioned test circuits, they are NC.
14/28
Series
■TYPICAL PERFORMANCE CHARACTERISTICS

(1) Efficiency vs. Output Current
XC9128 (VOUT=3.3V) XC9128 (VOUT=5.0V)

L=4.7μH(LTF5022-LC),CL =30μF(LMK212BJ106KG ×3) L=4.7μH(LTF5022-LC),CL =30μF(LMK212BJ106KG ×3)
VEN=6V,VFO =OPEN,VAEN/ =0V VEN=6V,VFO =OPEN,VAEN/ =0V
RFB1 =270kΩ,RFB2 =43kΩ,CFB=12pF,CIN=10μF RFB1 =180kΩ,RFB2 =18kΩ,CFB=15pF,CIN=10μF
100 100
90 90
80 80
Efficiency: EFFI(%)
70 70 4.2V
60 3.0V 60 3.0V
50 50
1.8V
40 1.8V 40
30 V IN=0.8V 30
V IN=0.8V
20 20
PWM/PFM(VMODE=0V) PWM/PFM(VMODE=0V)
10 PWM(VMODE=VOUT)
10 PWM(VMODE=VOUT)
0 0
0.1 1 10 100 1000 0.1 1 10 100 1000
Output Current: I OUT (mA) Output Current: I OUT (mA)
XC9128 (VOUT=1.8V)
VEN=6V,VFO =OPEN,VAEN/ =0V
100
90
80
70
60 1.5V
50 1.2V
40
V IN=0.8V
30
20
PWM/PFM(VMODE=0V)
10
PWM(VMODE=VOUT)
0
0.1 1 10 100 1000
Output Current: I OUT (mA)
15/28
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)

(2) Output Voltage vs. Output Current
V M O D E = V O U T (P W M ),VEN=6V,VFO =OPEN,VAEN/ =0V V M O D E = 0 V (P W M / P FM ),VEN=6V,VFO =OPEN,VAEN/ =0V
L=4.7μH(LTF5022-LC),RFB1 =270kΩ,RFB2 =43kΩ L=4.7μH(LTF5022-LC),RFB1 =270kΩ,RFB2 =43kΩ
CL =30μF(LMK212BJ106KG ×3),CFB=12pF,CIN=10μF CL =30μF(LMK212BJ106KG ×3),CFB=12pF,CIN=10μF
3.5 3.5
Output Voltage : V OUT (V)

Output Voltage: V OUT (V)
3.4 3.4
3.0V V IN=0.8V,1.8V
V IN=0.8V,1.8V,3.0V
3.3 3.3
3.2 3.2
3.1 3.1
0.1 1 10 100 1000 0.1 1 10 100 1000

5.2 5.2
5.1 5.1
V IN=0.8V,1.8V,3.3V,4.2V V IN=0.8V,1.8V,3.3V,4.2V
5 5
4.9 4.9
4.8 4.8
0.1 1 10 100 1000 0.1 1 10 100 1000

2.0 2.0
1.9 1.9
V IN=0.8V,1.2V,1.5V V IN=0.8V,1.2V,1.5V
1.8 1.8
1.7 1.7
1.6 1.6
0.1 1 10 100 1000 0.1 1 10 100 1000
16/28
Series

(3) Ripple Voltage vs. Output Current
XC9128 (VOUT=3.3V) XC9128 (VOUT=3.3V)

L= 4 . 7 μ H (LT F5 0 2 2 - LC), C L = 3 0 μ F(LM K 2 1 2 B J1 0 6 K G × 3 ) L= 4 . 7 μ H (LT F5 0 2 2 - LC), C L = 2 0 μ F(LM K 2 1 2 B J1 0 6 K G × 2 )
100 100
Ripple Voltage: Vr (mVp-p)

PWM(VMODE=VOUT) PWM(VMODE=VOUT)
80 80
V IN=0.8V,1.8V,3.0V V IN=0.8V,1.8V,3.0V
60 60
0.8V 1.8V 3.0V 0.8V 1.8V 3.0V
40 40
20 20
0 0
0.1 1 10 100 1000 0.1 1 10 100 1000
XC9128 (VOUT=3.3V) XC9128 (VOUT=3.3V)

L= 1 0 μ H (LT F5 0 2 2 - LC), C L = 3 0 μ F(LM K 2 1 2 B J1 0 6 K G × 3 ) L= 1 0 μ H (LT F5 0 2 2 - LC), C L = 2 0 μ F(LM K 2 1 2 B J1 0 6 K G × 2 )
100 100
80 80 V IN=0.8V,1.8V,3.0V
V IN=0.8V,1.8V,3.0V
3.0V
60 0.8V 3.0V 60
1.8V
0.8V 1.8V
40 40
20 20
0 0
0.1 1 10 100 1000 0.1 1 10 100 1000
XC9128 (VOUT=5.0V) XC9128 (VOUT=1.8V)

L= 4 . 7 μ H (LT F5 0 2 2 - LC), C L = 3 0 μ F(LM K 2 1 2 B J1 0 6 K G × 3 ) L= 4 . 7 μ H (LT F5 0 2 2 - LC), C L = 2 0 μ F(LM K 2 1 2 B J1 0 6 K G × 2 )
100 100
80 80
V IN=0.8V,1.8V,3.3V,3.6V V IN=0.8V,1.2V,1.5V
60 60
0.8V 1.8V 3.3V 3.6V 0.8V 1.2V 1.5V
40 40
20 20
0 0
0.1 1 10 100 1000 0.1 1 10 100 1000
Output Current : I OUT (mA) Output Current: I OUT (mA)
17/28
(4) Supply Current 1 vs. Ambient Temperature (5) Supply Current 1 vs. Output Voltage
XC9128/29 XC9128/29
VBAT=VOUT,VFB=0V,VEN =3.3V VBAT=VOUT,VFB=0V,VEN =3.3V
10 10
Supply current1: I DD1 (mA)

Supply current1: I DD1 (mA)
8 V OUT =6.0V 8
5.0V
4.0V
6 6 25℃
85℃
4 4
2 2
Ta=-40℃
1.8V 2.5V 3.3V
0 0
-50 -25 0 25 50 75 100 1 2 3 4 5 6
Ambient Temperature: Ta (℃) Output Voltage : V OUT (V)
(6) Supply Current 2 vs. Ambient Temperature (7) Supply Current 2 vs. Output Voltage
XC9128 XC9128
VBAT=VOUT,VFB=VEN =3.3V VBAT=VOUT,VFB=VEN =3.3V
80 80
Supply current2 : I DD2 ( μA)
Supply current2 : I DD2 ( μA)
60 V OUT =6.0V 60
85℃ 25℃
40 40
Ta=-40℃
20 1.8V 3.3V 20
0 0
-50 -25 0 25 50 75 100 1 2 3 4 5 6
(8) Standby Current vs. Ambient Temperature (9) Standby Current vs. Output Voltage
XC9128/29 XC9128/29
VBAT=VOUT,VEN =0V VBAT=VOUT,VEN =0V
10 10
Standby Current : I STB ( μA)
Standby Current : I STB ( μA)
8 8
6 6
V OUT =6.0V 85℃ 25℃ Ta=-40℃

4 4
3.3V
2 2
1.8V
0 0
-50 -25 0 25 50 75 100 1 2 3 4 5 6
18/28
Series

(10) FB Voltage vs. Ambient Temperature (11) FB Voltage vs. Output Voltage
XC9128/29 XC9128/29
VBAT=VOUT,VEN =3.3V VBAT=VOUT,VEN =3.3V

0.460 0.460
Feedback Voltage: VFB (V)

Feedback Voltage: VFB (V)
0.455 0.455
6.0V 25℃
0.450 0.450
V OUT =1.8V,3.3V
0.445 0.445 Ta=-40℃
85℃
0.440 0.440
-50 -25 0 25 50 75 100 1 2 3 4 5 6
Ambient Temperature: Ta (℃) Output Voltage: V OUT (V)
(12) Oscillation Frequency vs. Ambient Temperature (13) Oscillation Frequency vs. Output Voltage
XC9128/29 XC9128/29
VBAT=VOUT,VEN =VMODE=3.3V,VFB= 0V,Rpull= 200Ω VBAT=VOUT,VEN =VMODE=3.3V,VFB= 0V,Rpull= 200Ω
1600 1600
Oscillation Frequency : f OSC (kHz)
Oscillation Frequency : f OSC (kHz)
1500 1500
V OUT =1.8V
1400 3.3V 1400
85℃
1300 1300
1200 1200
1100 1100
5.5V 25℃
Ta=-40℃
1000 1000
900 900
800 800
-50 -25 0 25 50 75 100 1 2 3 4 5 6
(14) Maximum Duty Cycle vs. Ambient Temperature (15) Maximum Duty Cycle vs. Output Voltage
XC9128/29 XC9128/29
VBAT=VOUT,VEN =3.3V,VFB= 0V,Rpull= 200Ω VBAT=VOUT,VEN =3.3V,VFB= 0V,Rpull= 200Ω
100 100
　.
Maximum Duty Cycle: MAXDTY (%)
Maximum Duty Cycle: MAXDTY (%)
V OUT =1.8V
96 96 Ta=-40℃
92 92
25℃
88 5.5V 3.3V 88 85℃
84 84
80 80
-50 -25 0 25 50 75 100 1 2 3 4 5 6
19/28

(16) PFM Switch Current vs. Ambient Temperature
XC9128 (VOUT=5.0V) XC9128 (VOUT=3.3V)

IOUT=10mA,VEN=6V,VMODE=VAEN/ =0V IOUT=10mA,VEN=6V,VMODE=VAEN/ =0V
400 400
V IN=0.9V V IN=0.9V
350 350
PFM Switch Current : IPFM (mA)

300 300
1.8V,2.4V
250 1.8V,3.3V,4.2V 250
200 200
150 150
100 100
50 50
0 0
-50 -25 0 25 50 75 100 -50 -25 0 25 50 75 100
Ambient Temperature: Ta (℃) Ambient Temperature: Ta (℃)
XC9128 (VOUT=1.8V)
IOUT=10mA,VEN=6V,VMODE=VAEN/ =0V
450
PFM Switch Current : I PFM (mA)
400 V IN=0.9V
350
300
1.5V
250
200
150
100
50
0
-50 -25 0 25 50 75 100
Ambient Temperature: Ta (℃)
(17) PFM Switch Current vs. Output Voltage
XC9128 (VIN=0.9V) XC9128 (VIN=1.5V)

IOUT=10mA,VEN=6V,VMODE=VAEN/ =0V,CIN=10μF IOUT=10mA,VEN=6V,VMODE=VAEN/ =0V,CIN=10μF
450 450
Ta=-40℃ Ta=-40℃
400 400
350 350
300 300
25℃
250 25℃ 250
200 85℃
85℃ 200
150 150
100 100
50 50
0 0
1 2 3 4 5 6 1 2 3 4 5 6
Output Voltage: V OUT (V) Output Voltage: V OUT (V)
20/28
Series

(18) Limit Current vs. Ambient Temperature (19) Limit Current vs. Output Voltage
XC9128/29 XC9128/29
VOUT=5V,VEN =VMODE=3.3V,VFB= 0V,Rpull= 200Ω VOUT=5V,VEN =VMODE=3.3V,VFB= 0V,Rpull= 200Ω
2200 2200
2000 2000
Limit Current : ILIM　(mA)
Limit Current : ILIM (mA)

1800 1800
Ta=-40℃
1600 4.2V 1600
1400 1400
3.3V
1200 V BAT =1.8V 1200 25℃
85℃
1000 1000
-50 -25 0 25 50 75 100 0 1 2 3 4 5 6
Ambient Temperature: Ta (℃) Supply Voltage: V BAT (V)
(20) Lx SW “Pch” ON Resistance vs. Ambient Temperature (21) Lx SW ”Pch” ON Resistance vs. Output Voltage
XC9128/29 XC9128/29
VOUT+50mV=VBAT=VLx ,VFB=0V VBAT=VLx =VOUT+50mV,VFB=0V
0.40 0.40
Lx SW"Pch"ON Resistance: R LxP (Ω)
Lx SW"Pch"ON Resistance: R LxP (Ω)
0.35 V OUT =1.8V 0.35
0.30 0.30 85℃

3.3V
0.25 0.25
0.20 0.20
0.15 0.15
25℃
0.10 0.10
6.0V
0.05 0.05 Ta=-40℃
0.00 0.00
-50 0 50 100 1 2 3 4 5 6
(22) Lx SW “Nch” ON Resistance vs. Ambient Temperature (23) Lx SW ”Nch” ON Resistance vs. Output Voltage
XC9128/29 XC9128/29
VOUT=VBAT,VLx =50mV,VFB=0V VOUT=VBAT,VLx =50mV,VFB=0V
0.35 0.35
Lx SW"Nch"ON Resistance: R LxN (Ω)
Lx SW"Nch"ON Resistance: R LxN (Ω)
V OUT =1.8V
0.30 0.30
0.25 85℃
0.25 3.3V
0.20 0.20
0.15 0.15
0.10 25℃
0.10
6.0V
Ta=-40℃
0.05 0.05
0.00 0.00
-50 -25 0 25 50 75 100 1 2 3 4 5 6
21/28
(24) Soft Start Time 1 vs. Ambient Temperature (25) Soft Start Time 1 vs. Output Voltage
XC9128/29 XC9128/29
VBAT=VOUT,VFB=VFO=0V,VEN =0V→VBAT VBAT=VOUT,VFB=VFO=0V,VEN =0V→VBAT

10.0 10.0
Soft Start Time : t SS1 (ms)

Soft Start Time : t SS1 (ms)
8.0 8.0
Ta=-40℃
4.2V
3.3V 6.0
6.0
4.0 4.0 25℃

V OUT =0.9V 1.8V 85℃
2.0 2.0
-50 -25 0 25 50 75 100 1 2 3 4 5 6
(26) Flag Output Current vs. Ambient Temperature (27) Flag Output Current vs. Output Voltage
XC9128 XC9128
VOUT=VBAT,VEN =VMODE=3.3V,VFO=0.25V,VFB=VAEN/=0V VOUT=VBAT,VEN =VMODE=3.3V,VFO=0.25V,VFB=VAEN/=0V
2.5 2.5
Flag Output Current: I FO_OUT (mA)
Flag Output Current : I FO_OUT (mA)
6.0V Ta=-40℃
2.0 2.0
1.5 1.5
3.3V 85℃
25℃
1.0 V OUT =1.8V 1.0
0.5 0.5
0.0 0.0
-50 -25 0 25 50 75 100 1 2 3 4 5 6
(28) Flag Leakage Current vs. Ambient Temperature (29) Flag Leakage Current vs. Output Current
XC9128 XC9128
VBAT=VOUT=VMODE=3.3V,VFB=VAEN/=VEN =0V VBAT=VOUT=VMODE=3.3V,VFB=VAEN/=VEN =0V
1.0 0.10
Flag Leakage Current: I FO_Leak (μA)
Flag Leakage Current: I FO_Leak (μA)
0.9 0.09
0.8 0.08
0.7 0.07
0.6 0.06
0.5 0.05
0.4 0.04
0.3 0.03
Ta=-40℃,25℃,85℃
0.2 V FO=3.3V,6.0V 0.02
0.1 0.01
0.0 0.00
-50 0 50 100 0 1 2 3 4 5 6
Ambient Temperature: Ta (℃) Flag Output Voltage: V FO (V)
22/28
Series

(30) Low Voltage Protection Voltage vs. Ambient Temperature
XC9128
VBAT=1.2V,VEN =VMODE=3.3V,VAEN/=VFB=0V
(V)
1.60
LVP
1.55
Low Voltage Protection Voltage: V
1.50
1.45
1.40
1.35
1.30
-50 -25 0 25 50 75 100
(31) EN ”H” Voltage vs. Ambient Temperature (32) EN ”H” Voltage vs. Output Voltage
XC9128/29 XC9128/29
VBAT=VOUT,VFB=0V VBAT=VOUT,VFB=0V
0.65 0.65
0.60 0.60
Ta=-40℃
EN "H" Voltage: V ENH (V)
EN "H" Voltage: V ENH (V)
0.55 0.55
0.50 0.50
0.45 0.45
0.40 0.40
0.35 V OUT =1.8V,3.3V,5.0V 0.35 25℃ 85℃
0.30 0.30
0.25 0.25
0.20 0.20
-50 -25 0 25 50 75 100 1 2 3 4 5 6
Ambient Temperature: Ta(℃) Output Voltage: V OUT (V)
(33) EN ”L” Voltage vs. Ambient Temperature (34) EN ”L” Voltage vs. Output Voltage
XC9128/29 XC9128/29
VBAT=VOUT,VFB=0V
0.65
VBAT=VOUT,VFB=0V 0.65
0.60 0.60
0.55
EN "L" Voltage:V ENL (V)
EN "L" Voltage: V ENL (V)
0.55 Ta=-40℃
0.50 0.50
0.45 0.45
0.40 0.40
0.35 0.35
25℃ 85℃
0.30 V OUT =1.8V,3.3V,5.0V 0.30
0.25 0.25
0.20 0.20
-50 -25 0 25 50 75 100 1 2 3 4 5 6
Ambient Temperature: Ta(℃) Output Voltage: V OUT (V)
23/28

(35) MODE ”H” Voltage vs. Ambient Temperature (36) MODE ”H” Voltage vs. Output Voltage
XC9128/29 XC9128/29
L=4.7μH(CDRH4D28C),CL =30μF(LMK212BJ106KG ×3) L=4.7μH(CDRH4D28C),CL =30μF(LMK212BJ106KG ×3)
IOUT=10mA,VEN=3.3V,VAEN/ =0V,CIN=10μF IOUT=10mA,VEN=3.3V,VAEN/ =0V,CIN=10μF
0.65 0.65
0.60 0.60
MODE "H" Voltage : VMODEH (V)
MODE "H" Voltage : VMODEH (V)

0.55 0.55 Ta=-40℃
0.50 0.50
0.45 0.45
0.40 V OUT =1.8V,3.3V,5.0V 0.40
25℃
85℃
0.35 0.35
0.30 0.30
0.25 0.25
0.20 0.20
-50 -25 0 25 50 75 100 1 2 3 4 5 6
(37) MODE ”L” Voltage vs. Ambient Temperature (38) MODE ”L” Voltage vs. Output Voltage
XC9128/29 XC9128/29
L=4.7μH(CDRH4D28C),CL =30μF(LMK212BJ106KG ×3) L=4.7μH(CDRH4D28C),CL =30μF(LMK212BJ106KG ×3)
IOUT=10mA,VEN=3.3V,VAEN/ =0V,CIN=10μF IOUT=10mA,VEN=3.3V,VAEN/ =0V,CIN=10μF
0.65 0.65
0.60 0.60
MODE "L" Voltage : V MODEL (V)
MODE "L" Voltage : V MODEL (V)
0.55 0.55
0.50 0.50 Ta=-40℃
0.45 0.45
0.40 0.40
0.35 V OUT =1.8V,3.3V,5.0V 0.35 25℃
0.30 0.30 85℃
0.25 0.25
0.20 0.20
-50 -25 0 25 50 75 100 1 2 3 4 5 6
(39) AEN/Voltage vs. Ambient Temperature (40) AEN/Voltage vs. Output Voltage
XC9128 XC9128
VBAT=VOUT,VEN =3.3V,VFB=0V VBAT=VOUT,VEN =3.3V,VFB=0V
0.90 0.9
AEN/ Voltage: V AEN/ (V)
0.85 0.85 25℃

AEN/ Voltage: V AEN/ (V)
6.0V
0.80 0.8
V OUT =1.8V,3.3V Ta=-40℃ 85℃
0.75 0.75
0.70 0.7
-50 -25 0 25 50 75 100 1 2 3 4 5 6

24/28
Series

(41) Load Transient Response
XC9128B45CDR(PWM Control) XC9128B45CDR(PWM/PFM Automatic Switching Control)

VIN=1.8V,VOUT=3.3V,IOUT=10mA⇔100mA VIN=1.8V,VOUT=3.3V,IOUT=10mA⇔100mA
VEN=VMODE=3.3V,VAEN/ =0V,Ta=25℃ VEN=3.3V,VMODE=VAEN/ =0V,Ta=25℃
3.4 3.4
Output Voltage: VOUT (V)

Output Voltage
Output Voltage
3.3 3.3
3.2 3.2
3.1 3.1
100mA 100mA
3.0 3.0
10mA 10mA Output Current
Output Current
2.9 2.9
Time(400μsec/div) Time(400μsec/div)

5.1 5.1
5.0 Output Voltage 5.0 Output Voltage
4.9 4.9
4.8 4.8
100mA 100mA
4.7 4.7
10mA Output Current 10mA Output Current
4.6 4.6

5.2 5.2
Output Voltage Output Voltage

5.0 5.0
4.8 4.8
4.6 4.6
300mA 300mA
4.4 4.4
10mA Output Current 10mA Output Current

4.2 4.2
25/28
■PACKAGING INFORMATION
For the latest package information go to, www.torexsemi.com/technical-support/packages
PACKAGE OUTLINE / LAND PATTERN THERMAL CHARACTERISTICS
MSOP-10 MSOP-10 PKG Standard Board MSOP-10 Power Dissipation
USP-10B USP-10B PKG Standard Board USP-10B Power Dissipation
26/28
Series
■MARKING RULE
●USP-10B ① represents product series.
MARK PRODUCT SERIES

8 XC9128 series
9 XC9129 series
② represents transistor built-in, output voltage freely set (FB voltage),

integral protection type.
MARK PRODUCT SERIES
●MSOP-10 B With integral protection
D Without integral protection
③④ represents reference voltage.
MARK
VOLTAGE(V)
③ ④
4 5 0.45
⑤ represents oscillation frequency.
MARK OSCILLATION FREQUENCY(kHz)

C 1200
⑥⑦ represents production lot number

01 to 09, 10 to 99, 0A~ 0Z, 1A ~9Z,A0~Z9,AA~ZZ in order.
(G, I, J, O, Q, W excluded)
*No character inversion used
27/28
1. The product and product specifications contained herein are subject to change without notice to
improve performance characteristics. Consult us, or our representatives before use, to confirm that
the information in this datasheet is up to date.
2. The information in this datasheet is intended to illustrate the operation and characteristics of our
products. We neither make warranties or representations with respect to the accuracy or
completeness of the information contained in this datasheet nor grant any license to any intellectual
property rights of ours or any third party concerning with the information in this datasheet.
3. Applicable export control laws and regulations should be complied and the procedures required by
such laws and regulations should also be followed, when the product or any information contained in
this datasheet is exported.
4. The product is neither intended nor warranted for use in equipment of systems which require
extremely high levels of quality and/or reliability and/or a malfunction or failure which may cause loss
of human life, bodily injury, serious property damage including but not limited to devices or equipment
used in 1) nuclear facilities, 2) aerospace industry, 3) medical facilities, 4) automobile industry and
other transportation industry and 5) safety devices and safety equipment to control combustions and
explosions. Do not use the product for the above use unless agreed by us in writing in advance.
5. Although we make continuous efforts to improve the quality and reliability of our products;
nevertheless Semiconductors are likely to fail with a certain probability. So in order to prevent personal
injury and/or property damage resulting from such failure, customers are required to incorporate
adequate safety measures in their designs, such as system fail safes, redundancy and fire prevention
features.
6. Our products are not designed to be Radiation-resistant.
7. Please use the product listed in this datasheet within the specified ranges.
8. We assume no responsibility for damage or loss due to abnormal use.
9. All rights reserved. No part of this datasheet may be copied or reproduced unless agreed by Torex
Semiconductor Ltd in writing in advance.
TOREX SEMICONDUCTOR LTD.
28/28

XC9128 XC9129

Uploaded by

Copyright:

Available Formats

XC9128 XC9129

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

XC9128 XC9129

Uploaded by

Copyright:

Available Formats

XC9128/XC9129 series is Discontinued.

■TYPICAL APPLICATION CIRCUIT ■TYPICAL PERFORMANCE

Output Current: I OUT (mA)

DESIGNATOR ITEM SYMBOL DESCRIPTION

DESIGNATOR ITEM SYMBOL DESCRIPTION

2. MODE Pin Function

■ABSOLUTE MAXIMUM RATINGS

PARAMETER SYMBOL RATINGS UNITS

LX Leak Current ILXL VIN=VOUT= VLX, VFB=0V - 1 - μA ⑤

■ELECTRICAL CHARACTERISTICS (Continued)

EN "L" Current IENL VIN=VOUT=VFB=6.0V, VEN=0V -0.1 - - μA ②

MODE "H" Current IMODEH VIN=VOUT=VFB=VMODE=6.0V - - 0.1 μA ②

MODE "L" Current IMODEL VIN=VOUT=VFB=6.0V, VMODE=0V -0.1 - - μA ②

AEN/ "H" Current (*7) IAEN/H VIN=VOUT=VFB=VAEN/=6.0V - - 0.1 μA ②

AEN/ "L" Current (*7) IAEN/L VIN=VOUT=6.0V, VEN=0V, VAEN/=0V -0.1 - - μA ②

FB "H" Current IFBH VIN=VOUT=VFB=6.0V - - 0.1 μA ②

FB "L" Current IFBL VIN=VOUT=6.0V, VFB=0V -0.1 - - μA ②

For the Circuit No.7, unless otherwise stated, VEN=VMODE=3.3V

3 : LX SW "Pch" ON resistance=(VLx-VOUT pin test voltage)÷100mA

4 : Testing method of LX SW "Nch" ON resistance is stated at test circuits.

5 : Current flowing through the Nch driver transistor is limited.

This is only available with the XC9128B type.

■TYPICAL APPLICATION CIRCUIT

<Output Voltage Setting>

VOUT=0.45 × (RFB1 + RFB2) / RFB2

VOUT (V) RFB1 (kΩ) RFB2 (kΩ) CFB (pF)

* CL1 should be selected in 10μF or higher.

<Reference Voltage Source>

<Ramp Wave Circuit>

< Maximum Current Limit>

Current Limit LEVEL

■OPERATIONAL EXPLANATION (Continued)

The XC9129 series does not have adaptor enable function.

<Error Flag >

■NOTE ON USE (Continued)

Wave Form Measure Point

< Circuit No.2 > < Circuit No.3 >

A BAT MODE A A BAT MODE

PGND AGND PGND AGND

< Circuit No.4 > <Circuit No.5 >

PGND AGND PGND AGND

<Circuit No.6 > <Circuit No.7 >

PGND AGND PGND AGND

Measurement method for ON resistance of the Lx switch

■TYPICAL PERFORMANCE CHARACTERISTICS

XC9128 (VOUT=3.3V) XC9128 (VOUT=5.0V)

Output Current: I OUT (mA) Output Current: I OUT (mA)

Output Current: I OUT (mA)

■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)

Output Voltage : V OUT (V)

Output Current: I OUT (mA) Output Current: I OUT (mA)

V M O D E = V O U T (P W M ),VEN=6V,VFO =OPEN,VAEN/ =0V V M O D E = 0 V (P W M / P FM ),VEN=6V,VFO =OPEN,VAEN/ =0V

Output Voltage: V OUT (V)

Output Current: I OUT (mA) Output Current: I OUT (mA)

V M O D E = V O U T (P W M ),VEN=6V,VFO =OPEN,VAEN/ =0V V M O D E = 0 V (P W M / P FM ),VEN=6V,VFO =OPEN,VAEN/ =0V

Output Current: I OUT (mA) Output Current: I OUT (mA)

■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)

XC9128 (VOUT=3.3V) XC9128 (VOUT=3.3V)