GRANDSTAND SEATING INFO

Pg.

GRANDSTAND SEATING
CONTENT :

1) TECHNICAL SPECIFICATIONS
2) TECHNICAL SPECIFICATIONS
3) TWO TYPICAL SECTION & DIMENSIONS
4) GRANDSTAND PARTS
5) SECTION SHOWING DIFFERENT TRUSS COMBINATION
6) VOMITORY STAIR ACCESS WITH SINGLE AILSE
7) VOMITORY STAIR ACCESS WITH DOUBLE AISLE
8) REAR LOADING STAIR ACCESS
9) FRONT STAIR ACCESS TO GRANDSTAND
10) FRONT LOADING STAIRCASE & LANDING ACCESS TO ELEVATED GRANDSTAND
11) TYPICAL REAR LOADING PAKAR STAIRCASE ACCESS WITH LANDING
12) FRONT PLATFORM EXTENSION OPTIONS
13) RINGLOCK BASE JACK OPTIONS
14) PS1 - DESIGN FOR PAKAR SEATING
15) PLYWOOD FIRE REPORT
16) PLYWOOD FIRE REPORT
17) PLYWOOD SPEC
18) PLASTIC SEAT TEST CERT
19) FLAME RETARDANT EVENT SCREEN
Pg1

PAKAR GRANDSTAND
TECHNICAL SPECIFICATIONS
Grid Width : 1.800m c/c Wide Bay
Grid Depth : 3.000m c/c Deep Bay

Gradients and Heights Setting ( Riser) : .125mm , .250mm and .375mm

(9 deg) (18.5 deg) (26.5 deg)
Seating Bay length : 1.800m (4 x Seats per bay)

Seat Depth : .750mm

Seat pan : .340mm

Seat Spacing : .450mm c/c

Seat Rest : .370mm for Bucket seat

Spacing Between 2 Rows : .350mm for Bucket seat

2
Load capacity : 5KN/ m
2
Dead Load : .025 KN/m

MATERIAL
Seating Truss
Each Truss T4 supports 4 x rows of 4 seats with a .750mm spacing between the rows . The truss is 3.000m long
with a hot dip galvanized finish and made with high Tensile strength steel tube.
The truss structure is fully welded to produce a rigid framework. The truss frame are inter-locked together
horizontally and vertically.
The T4 Truss come in three riser heights: 125mm ( Low), 250mm (Med), 375mm ( High)

Ringlock - Standards - Ledgers - Braces

These are constructed from hot dip galvanized high Tensile steel pipe. The diameters are 48.3mm x 3.2mm wt
and 30.5mm x 2mm wt. pipe with wedge locking pins.

Deck Units ( Platforms)

Deck Units ( Platforms) are made of 12mm thick anti slip Phenolic film faced - plywood. The plywood is fixed and
supported on 3 x units of steel SHS 40 x 40 x 3mm thick with a hot dip galvanised finish. When installed onto the
grandstand truss the deck units is held captive by a cleat on the truss frame and provide a self - interlocking
system.
Pg2

PAKAR GRANDSTAND
Seat Support Beam (4 x Seats)
The Steel Seat support beam unit is fixed into the Truss Frame units with a Integral hooks and are locked onto the
Frame with a hidden locking pin. The seat units when not in use are designed so they can be nested and stacked.
The seats are made of UV stabilized polypropylene plastic with a bright and smooth appearance.
Buck Seat : Clearway is : 350mm spacing

Single Aisle Seat

4 x Seat support beam
Guardrails / Balustrades
Side Guardrails are connected to the frame unit and are positioned to provide a barrier height of 1.100m above
the deck level. The front and rear balustrades are connected to high strength posts that are connected to the
truss frame unit. The imposed loads of the barriers 1KN/m to 2KN/m.
The balustrades rails are constructed to restrict any object greater than 100mm from passing through.

Post
Link Guardrail

Side Guardrail
Rear Guardrail Stair Guardrail
Aisles and Gangways
Aisle and gangways are generously proportioned to provide for clear unobstructed access. The access to the
grandstand is provided by use of a front staircase, rear staircase or internal vomitory staircase access

Stair step
Stair access step Stair step 1 x step

The stairs and aisle steps have yellow reflective strips attached to the front face of each nose of the step.
Also attached to the front of the steps are non slip tape strip.

C/Step Infill ( Infill's between Decks lifts)

The galvanized steel C/Step infill comes in three rises, 125mm (9 deg) 250mm (18.5 deg) and 375mm (26.5 deg)
and used to infill the gaps between the deck units. The C/step infill is fitted between the two deck units and
placed under the seating unit .The C/Step seals off the decks and eliminates any gaps no greater than 100mm

C Step profile
Pg3

PAKAR GRANDSTAND
SECTION SHOWING DIMENSION FOR TWO
SECTION SHOWING DIMENSION FOR
TYPICAL PAKAR GRANDSTANDS
TYPICAL GRANDSTAND

250mm Rise Grandstand , 18.5 Deg Angle

375mm Rise Grandstand , 26.5 Deg Angle

Pg4

PAKAR GRANDSTAND
TYPICAL PAKAR GRANDSTAND PARTS

SECTION

REAR ELEVATION

1.800m Bay

PLAN
Pg5

PAKAR GRANDSTAND
PAKAR GRANDSTAND SHOWING THE USE OF ALL THREE RISER HEIGHTS

SECTION THROUGH GRANDSTAND 125mm & 250mm & 375mm RISER TO FORM THE GRANDSTAND

END ELEVATION OF THE GRANDSTAND SHOW GUARDRAILS

GL TRUSS F5 125/75 STARTING TRUSS 0.5m x 3.000m LONG

Pg6

PAKAR GRANDSTAND
VOMITORY STAIR ACCESS TO GRANDSTAND WITH A SINGLE SIDE AISLE

LANDING
PLATFORM

PLAN
Stair stringer Stair Steps Stair stringer
S6 (6 x Steps) 280mm going S3 (3 x Steps)
Lower Step
to suit

Vomitory
1.270m
Landing
Wide Step
Platform

PLAN STAIRCASE

Vomitory
Landing SEATING TRUSS
Platform

Lower Step to suit rise

(1 or 2 step options)
STAIR STRINGER
S6 (6 x Steps)

ELEVATION
Pg7

PAKAR GRANDSTAND
VOMITORY STAIR ACCESS TO GRANDSTAND WITH DOUBLE SIDE AISLE

LANDING
PLATFORM

PLAN SHOWING THE VOMITORY STAIR

ACCESS THROUGH THE GRANDSTAND

SECTION SHOWING VOMITORY STAIRCASE SECTION SHOWING THE

AND GUARDRAILS TO THE VOMITORY ACCESS ROUTE TOP AND SIDE GUARDRAILS
Pg8

PAKAR GRANDSTAND
REAR STAIR ACCESS TO THE GRANDSTAND

S6 Stairs Stringer
Stair Step 1.270m

Staircase
S6 Stairs Stringer

TOP LANDING PLATFORM 1.80m x

0.481m

Seat support beam x 4

Stair access Step 1.8m

Std Platform 1.8m x .520m

PLAN VIEW
Pg9

PAKAR GRANDSTAND
PAKAR FRONT STAIR ACCESS ONTO GRANDSTAND
Pg10

PAKAR GRANDSTAND
TYPICAL PAKAR FRONT LOADING STAIRCASE ACCESS TO ELEVATED GRANDSTAND
TYPICAL PAKAR FRONT LOADING STAIR ACCESS TO GRANDSTAND
Step
280mm

1.800m x 1.500m
Landing platform

1.500m Landing side PLAN

guardrail S6 Stairs Stringer S3 Stairs Stringer

1.800m Landing side

guardrail

S6 Stairs Stringer
6 x Steps

SIDE ELEVATION

1.5m LANDING
TRUSS 250/75

1.5m RINGLOCK
STANDARD
RINGLOCK
3m 1.5m BRACE
RINGLOCK
3m LEDGER

TYPICAL FRONT STAIRS AND

LANDING ACCESS TO THE
FRONT OF GRANDSTAND
END ELEVATION
Pg11

PAKAR GRANDSTAND
TYPICAL PAKAR REAR LOADING STAIRS ACCESS WITH TOP LANDING
1.5m

1.5m

1.5m

PLAN
1.5m x 1.2m H

END ELEVATION

1.5m

SIDE ELEVATION
Pg12

FRONT PLATFORM EXTENSION OPTIONS TO THE GRANDSTAND

FIRST SIDE GUARD RAIL 25-75

PROVIDES FRONT
LANDING FOR THE RINGLOCK 2m
FRONT ROW OF SEATS STANDARD

1m RINGLOCK
STANDARD

RINGLOCK RINGLOCK RINGLOCK

COLLAR 3m LEDGER COLLAR

FRONT CANTILEVER 25/75

FRONT CANTILEVER TRUSS

SIDE GUARD RAIL INSIDE DOWN 25-75

SIDE GUARD RAIL 25-75

1m RINGLOCK
STANDARD
RINGLOCK
3m LEDGER RINGLOCK
COLLAR
1ST ROW SUPPORT

1ST ROW FRONT CANTILEVER

Pg13

RINGLOCK BASE JACK OPTIONS, WITH PAKAR SEATING SYSTEM

1m RINGLOCK
STANDARD
RINGLOCK
COLLAR

BASE JACK
400mm
pg14

PS1- DESIGN FOR PAKAR SEATING SYSTEM IN NEW ZEALAND

Pg15

PLYWOOD DECKING FIRE REPORT SEATING SYSTEM

Pg16

PLYWOOD DECKING FIRE REPORT SEATING SYSTEM

Pg17

PLYWOOD DECKING SPEC

Pg18

PLASTIC SEAT TEST CERTIFCATE

Pg19

FLAME RETARDANT EVENT SCREENING TEST CERTIFCATE

THE FOLLOWING PRODUCT IS USED WHERE A FLAME RETARDANT EVENT SCREEN IS REQUIRED
TO BE SECURED TO THE OUTSIDE OF A GRANDSTAND OR HOSPITALITY PLATFORM STRUCTURE
TECHNICAL SPECIFICATIONS SIZE : 240g/m2 x 2.000m Wide x 50.000m Long rolls
COLOUR : Black