AX Hybrid PRO V1.0.2 Release Note

AX Hybrid PRO V1.0.
2 Release Notes
AX Hybrid PRO
Version: V1.0.2
Release Note
(2022-07-22)
1. Firmware Basic Information
Firmware Firmware Version V1.0.2_build220719

Basic
DS-PHA48-EP
Information Device Type
DS-PHA64-LP
Notes:
1. Please update firmware to the latest version to ensure the perfect user experience.
2. For installers, it is recommended to install and maintain devices via Hik-ProConnect.
2. V1.0.2 Upgrade Note
2.1 Added Function:

1) Added R3 protocol peripheral, including wireless detectors,
sounders, and output modules
1. Support to display the status of wireless detectors, including temperature,
humidity, battery status, signal strength, detector status, tamper-proof status,
alarm trigger status, version number

AX Hybrid PRO V1.0.2 Release Notes
The two detectors DTAM CURTAIN and PIR AM CURTAIN support detecting
whether the Anti-Masking is triggered or not.
DS-PDEB1-EG2-WE/B Support single or double key alarm, after enabled PD6662,
short press and long press cross trigger will upload confirm alarm
Detectors support Find Me, Detection Zone Test, and Signal Strength Test
The new detector models are as follows:

DS-PDP15P-EG2-WE/WB
DS-PDD12P-EG2-WE/WB
DS-PDPG12P-EG2-WE/WB）
DS-PDC15-EG2-WE/WB
DS-PDMCS-EG2-WE/WB
DS-PDWL-E-WE/WB
DS-PDEB1-EG2-WE/WB
DS-PDEBP1-EG2-WE/WB
DS-PDTPH-E-WE/WB
DS-PDCL12-EG2-WE/WB
DS-PDC10DM-EG2-WE/WB
DS-PDC10AM-EG2-WE/WB
2. Support to display the status of wireless sounders, including temperature, battery
power, signal strength, online status, whether to connect to the main power status, and the
version number;
The new sounder models are as follows:

DS-PS1-E-WE/WB
DS-PS1-I-WE/WB
When the system is disarmed, the tamper of the outdoor sounder cannot be triggered;
Configurable indicator light or buzzer for arm and disarm linkage sounder;
After enabled the PD6662, the confirmation alarm can be linked;
Sounders support Find Me, Volume Test, and Signal Strength Test
3. Support to display the temperature, power load, signal strength, version number of
the wireless output module
The new relay module models are as follows

DS-PM1-O1L-WE/WB
DS-PM1-O1H-WE/WB
Relay modules support Find Me, Signal Strength Test

2) Supports Wired PIRCAM detector

Wired PIRCAM detector support alarm linkage snapshot, manual snapshot;
Wired PIRCAM model is DS-PDPC12P-EG2

Wired PIRCAM supports configuration sensitivity, LED, Images resolution, Images In
Series, and trigger interval;
After the PIRCAM alarms, it will take a snapshot of itself and upload it to EZVIZ
Wired PIRCAM supports manually capture pictures through the web, and the captured
pictures will be saved locally.

3) Added BUS scan registration function

The WEB can manually open the bus scanning function to detect the unregistered wired
peripherals on the bus, and present the scanned unregistered peripherals of a list. You can
manually add unregistered peripherals in the list, and the completion of the addition
prompts success.
Click Enroll to add the scanned peripherals
4) Support wired output module, Tri-X wireless receiver

Support display module name, module model, version information, online status,
tamper status
BUS module supports Find Me function (operable via WEB and APP)
The new wired output module models as follows:

DS-PM1-O4L-H
DS-PM1-O4H-H
The new Tri-X wireless receiver model is DS-PM1-RT-HWE/WB
You can view the mounted devices of the module through the APP
Devices mounted under the Tri-X wireless receiver

Devices mounted under the wired output module
5) Wired Zone supports 3EOL Function
After the 3EOL function of the wired zone is enabled, the zone can detect two new
detector status of masking and faults

6) Support wired PIRCAM for video review function
Only non-PIRCAM zone detectors can be linked with other PIRCAM; after linkage, when
an alarm is triggered in this zone, the linked PIRCAM will be to capture pictures.
After the zone 1 linked with the zone 11 (PIRCAM), when the zone 1 generates an alarm,
it will link the PIRCAM to take a picture and synthesize the video and upload it to the APP
for association with the alarm of the zone 1
7) Added auto arm sound prompt enable

When this configuration item is turned on, the auto arming and auto disarming need
to be turned on at the same time to take effect. If this configuration item is turned
off, the automatic arming countdown will be silent.
2. Feature Optimization:
1) BUS speed adaptive
In low-rate mode, it can meet the communication requirements of not less than 900m,
and the response delay of devices on the bus doesn’t exceed 1s.
2) When the arm mode of the delay zone is “and”, it can be configured
as a public zone
3) LCD keypad added Entry Delay interface

The LCD keypad added Entry Delay interface, and wake up the keypad and wake
up the button when entering the delay time
4) Module display optimization

The module management page information can be displayed all, and the
corresponding module type can be selected according to the drop-down box.

5) Added Motion Detector Restore reporting configuration

Can control whether the Motion detector Restore report CID is uploaded to the ARC and
EZVIZ
6) Web interface added Peripheral Control interface

The Web interface added the Peripheral Control interface, which can perform find me
operations on the bus module on the web

Remarks:
 Hikvision reserves the right to change, alter or withdraw the above notification without prior
notice.
 Product design and specifications are subject to change without prior notice.
 The Hikvision firmware may contain errors known as errata which may cause the product to
deviate from published specifications. Current characterized errata are available on request.
 Hikvision is not liable for any typing or printing errors.
Hikvision Digital Technology CO., Ltd.

No. 555 Qianmo Road, Binjiang District, Hangzhou 310051,
China
Tel: +86-571-8807-5998
FAX: +86-571-8993-5635
Email: overseabusiness@hikvision.com

AX Hybrid PRO V1.0.2 Release Note

Uploaded by

Copyright:

Available Formats

AX Hybrid PRO V1.0.2 Release Note

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

AX Hybrid PRO V1.0.2 Release Note

Uploaded by

Copyright:

Available Formats

AX Hybrid PRO V1.0.

1. Firmware Basic Information

Firmware Firmware Version V1.0.2_build220719

2. V1.0.2 Upgrade Note

2.1 Added Function:

humidity, battery status, signal strength, detector status, tamper-proof status,

alarm trigger status, version number

whether the Anti-Masking is triggered or not.

DS-PDEB1-EG2-WE/B Support single or double key alarm, after enabled PD6662,

The new detector models are as follows:

2. Support to display the status of wireless sounders, including temperature, battery

The new sounder models are as follows:

After enabled the PD6662, the confirmation alarm can be linked;

the wireless output module

The new relay module models are as follows

Relay modules support Find Me, Signal Strength Test

2) Supports Wired PIRCAM detector

Wired PIRCAM model is DS-PDPC12P-EG2

Wired PIRCAM supports configuration sensitivity, LED, Images resolution, Images In

Series, and trigger interval;

pictures will be saved locally.

3) Added BUS scan registration function

Click Enroll to add the scanned peripherals

4) Support wired output module, Tri-X wireless receiver

The new wired output module models as follows:

Devices mounted under the Tri-X wireless receiver

Devices mounted under the wired output module

5) Wired Zone supports 3EOL Function

detector status of masking and faults

6) Support wired PIRCAM for video review function

for association with the alarm of the zone 1

7) Added auto arm sound prompt enable

off, the automatic arming countdown will be silent.

3) LCD keypad added Entry Delay interface

up the button when entering the delay time

4) Module display optimization

corresponding module type can be selected according to the drop-down box.

5) Added Motion Detector Restore reporting configuration

6) Web interface added Peripheral Control interface

operations on the bus module on the web

 Hikvision is not liable for any typing or printing errors.

Hikvision Digital Technology CO., Ltd.

You might also like