This document provides specifications for a TNC straight plug connector used with cable S67163, including:
1. Dimensions and construction details of the connector, such as materials used, weight, and finishes.
2. Performance specifications like impedance, frequency range, and voltage rating.
3. Instructions for installation, including required tools and dies.
This document provides specifications for a TNC straight plug connector used with cable S67163, including:
1. Dimensions and construction details of the connector, such as materials used, weight, and finishes.
2. Performance specifications like impedance, frequency range, and voltage rating.
3. Instructions for installation, including required tools and dies.
This document provides specifications for a TNC straight plug connector used with cable S67163, including:
1. Dimensions and construction details of the connector, such as materials used, weight, and finishes.
2. Performance specifications like impedance, frequency range, and voltage rating.
3. Instructions for installation, including required tools and dies.
This document provides specifications for a TNC straight plug connector used with cable S67163, including:
1. Dimensions and construction details of the connector, such as materials used, weight, and finishes.
2. Performance specifications like impedance, frequency range, and voltage rating.
3. Instructions for installation, including required tools and dies.
A Division of the Angelus Corporation Approved : Date 04/10/97
Ph (262) 246-0500 Fax (262) 246-0450 www.picwire.com Rev. 6 (06/18/14) PO Box 330 Sussex, WI 53089 Distribution : USER Uncontrolled Document
TNC Straight Plug
for S67163
1.80 1.17
TNC Plug per
Mil-Std 348
.56 .62
Features Not Shown : Safety Wire Holes, Gasket in Front
PERFORMANCE CONSTRUCTION
Nominal Impedance 50 Ohms Materials:
Body Brass, ASTM-B16, Frequency Range 0 - 12 GHz Alloy UNS 36000, H02 Center Contact Brass, ASTM-B16, Voltage Rating 500 VRMS Alloy UNS 36000, H02 Ferrule Brass, ASTM-B16, Insulation Resistance 5000 Megohms Alloy UNS 36000, Dead Soft, Weatherseals included CONNECTOR WEIGHT (Each) Dielectric TFE Fluorocarbon, ASTM-D1710, Type 1, Grade 1 1.15 ounces (32.60 grams) Finish : RoHS COMPLIANT Body, Ferrule Nickel Center Contact Gold Complies to RoHS Standards Applicable Standards MIL-STD 348 INSTALLATION MIL-PRF-39012
Pic Die Set MIL Spec Die Set Notes :
Center Contact Center Contact 1) A 2.5" piece of Raychem ATUM heat shrink M22520 / 5 - 01 Tool, M22520 / 5-01 Tool, P/N ATUM-16/4-0 provided with connector for *PIC 190518A Hex Crimp Die MIL Spec *M22520 / 5-57 purpose of strain relief & moisture protection. (.098 hex) (.100 B hex) 2) Please refer to T-190XXX Termination Instruction Crimp Ferrule Crimp Ferrule sheet for strip dimensions & instructions. M22520 / 5 - 01 Tool, M22520 / 5-01 Tool, *PIC 190518A Hex Crimp Die MIL Spec *M22520 / 5-43 (.270/.340 hex) (.268 A hex)
* Notes: 1. PIC 190518 Crimp Die Set superceded by PIC 190518A; either is acceptable for use with 190508 Connectors. 2. MIL Spec die to be used on the smaller diameter area of ferrule only. Not the larger "Bell" area on end.
PIC Wire & Cable Connector User specification sheets are non-controlled documents. Please contact PIC Wire and Cable or visit the PIC website (www.picwire.com) to ensure the latest revision of the drawing is being viewed.
