WEAVER'S COVE ENERGY WEAVERS COVE OFFSHORE BERTH PROJECT Resource Report 13

APPENDIX D DESIGN CODES AND STANDARDS

WEAVER'S COVE ENERGY WEAVERS COVE OFFSHORE BERTH PROJECT Resource Report 13

13.D

DESIGN CODES AND STANDARDS

The following federal agencies have been assigned the tasks of permitting the construction and operation of LNG facilities. Federal Energy Regulatory Commission Site selection, design and construction US Coast Guard (USCG) Marine design, assessment of waterway suitability Pipeline and Hazardous Materials Safety Administration (PHMSA) Prepares and enforces LNG safety regulations in 49 CFR (Code of Federal Regulations) The jurisdiction of FERC is shown in Figure 13.D-1 below:
Figure 13.D-1. Federal Agency Jurisdiction

The LNG Transfer System design and construction are to comply with the applicable US Federal Government Regulations, specifically: 1. 33 CFR Part 127, which references: 2. ASME B31.3-1993 - Process Piping - ASME Code for Pressure Piping, B31 3. NFPA 59A, Standard for the Production, Storage, and Handling of Liquefied Natural Gas (LNG), 1994 Edition 4. Other documents incorporated by reference in 33 CFR Part 127 para. 127.003 Other documents selected as design and engineering guidance1 for this project include those provided in the following sections. The list provided here is not meant to be exclusive.
1

Guidance is intended to mean that these documents will be adopted for use to extent practicable and where they do not conflict with mandatory requirements listed in 33 CFR Part 127

13.D-1

WEAVER'S COVE ENERGY WEAVERS COVE OFFSHORE BERTH PROJECT Resource Report 13

1.0

LOCAL CODES

Local codes, as applicable. 2.0 ACI AMERICAN CONCRETE INSTITUTE US Product Standard PS-1 "Construction and Industrial Plywood" Standard Specifications for Tolerances for Concrete Construction and Materials and Commentary Specifications for Structural Concrete Guide for Concrete Floor and Slab Construction Guide for Measuring, Mixing, Transporting, and Placing Concrete Hot Weather Concreting Cold Weather Concreting Standard Specification for Curing Concrete Details and Detailing of Concrete Reinforcement Building Code Requirements for Structural Concrete and Commentary Guide to Formwork for Concrete Guide for the Design and Construction of Fixed Offshore Concrete Structures Design and Construction of Circular Wire and Strand Wrapped Prestressed Concrete Structures Design and Construction of Circular Pre-stressed Concrete Structures with Circumferential Tendons American Concrete Institute Detailing Manual

Concrete Formwork ACE 117/117R ACI 301 AC1 302.1R ACI 304R ACI 305R ACI 306R ACE 308.1 AC1 315 ACI 318/318R ACI 347 AC1 357R ACI 372R AC1 373R ACI SP-66 3.0

AEIC ASSOCIATION OF EDISON ILLUMINATING COMPANIES Specifications for Ethylene Propylene Rubber Insulated Shielded Power Cables Rated 5 through 69kV ANTI-FRICTION BEARING MANUFACTURERS ASSOCIATION, INC. Load Ratings and Fatigue Life for Ball Bearings AMERICAN GAS ASSOCIATION Operating Section Report, Purging Principles and Practice Classification of Gas Utility Areas for Electrical Installations

AEIC CS6

4.0

AFBMA

AFBMA 9 5.0 AGA

AGA Section 4.3.5 AGA XFO277 6.0

AGMA AMERICAN GEAR MANUFACTURERS ASSOCIATION 1981 Lubrication of Industrial Enclosed Gear Drives 13.D-2

AGMA 350.04

WEAVER'S COVE ENERGY WEAVERS COVE OFFSHORE BERTH PROJECT Resource Report 13

7.0

AISC AMERICAN INSTITUTE OF STEEL CONSTRUCTION

Specification for the Design, Fabrication and Erection of Structural Steel for Buildings and Code of Standard Practice for Steel and Bridges AISC S302 AISC S326 AISC S329 Code of Standard Practice for Steel Buildings and Bridges Design, Fabrication, and Erection of Structural Steel for Buildings, with Supplements Allowable Stress Design Specification for Structural Joints Using ASTM A 325 or ASTM A 490 Bolts

Manual of Steel Construction Allowable Stress Design LRFD Manual of Steel Construction 8.0 ANSI AMERICAN NATIONAL STANDARDS INSTITUTE Pipe Threads, General Purpose (Inch) Pipe Flanges and Flanged Fittings: NPS 1/2 through 24 Factory-Made Wrought Steel Buttwelding Fittings Forge Steel Fittings, Socket-Welding and Threaded Non-Ferrous Pipe Flanges Plain Washers Chemical Plant and Petroleum Refinery Piping Welded Aluminum-Alloy Storage Tanks Pipe Flanges and Flanged Fittings Steel Pipe Stainless Steel Pipe National Electrical Safety Code Low-Voltage Power Circuit Breakers and AC Power Circuit Protectors, Preferred Ratings, Related Requirements and Application Recommendations Trip Devices for AC and General Purpose DC Low-Voltage Power Circuit Breakers Switchgear - Low-Voltage AC Power Circuit Breakers Used in Enclosures - Test Procedures Switchgear - Metal-Enclosed Low-Voltage AC Power Circuit Breaker Switchgear Assemblies - Conformance Test Procedures Definitions For Power Switchgear Requirements for Electrical Analog Indicating Instruments (1990) Rigid Steel Conduit - Zinc Coated Specification for Octave-Band and Fractional Octave-Band Analog and Digital Filters Acoustics - Measurement of Airborne Noise Emitted by Information Technology and Telecommunications Equipment Part I, Performance Requirements, Combustible Gas Detectors, 1986

ANSI B1.20.1 ANSI B16.5 ANSI B16.9 ANSI B16.11 ANSI B16.31 ANSI B18.22.1 ANSI B31.3 ANSI B96.1 ANSI B16.5 ANSI B36.10 ANSI B36.19 ANSI C2 ANSI C37.16

ANSI C37.17 ANSI 037.50 ANSI C37.51 ANSI C37.100 ANSI C39.1 ANSI C80.1 ANSI S 1.11 ANSI S 12 .1 ANSI S12.13

13.D-3

WEAVER'S COVE ENERGY WEAVERS COVE OFFSHORE BERTH PROJECT Resource Report 13

9.0

API

AMERICAN PETROLEUM INSTITUTE Specification for Line Pipe Specification for Pipeline Valves Electrical Classification Sizing, Selection, and Installation of Pressure-Relieving Devices in Refineries Part I - Sizing and Selection Part II Installation Guide for Pressure-Relieving and Depressuring Systems Flanged Steel Safety Relief Valves Commercial Seat Tightness of Safety Relief Valves with Metal-to-Metal Seats Fire Test for Evaluation of Valve Stem Packing Valve Inspection and Testing Fire Test for Soft Seated Ball Valves Butterfly Valves: Double Flanged, Lug and Wafer Type Lubrication Shaft - Sealing and Control - Oil Systems for Special-Purpose Applications Design and Construction of Large, Welded, Low-Pressure Storage Tanks Tank Inspection, Repair, Alteration and Reconstruction Venting Atmospheric and Low-Pressure Storage Tanks Non-refrigerated and Refrigerated Recommended Practice and Supplementary Welding Guidelines for the Chemical, Oil and Gas Industries Manual of Petroleum Measurement Standards: Tank Calibration Calibration of Upright Cylindrical Tanks Using the Optical Reference Line Method Planning, Designing and Constructing Fixed Offshore Platforms Fire Test for Soft Seated Ball Valves Recommended Practice for Analysis, Design, Installation, and Testing of Basic Surface Safety Systems for Offshore Production Platforms-Seventh Edition Fire Prevention and Control on Open Type Offshore Production Platforms Recommended Practice for Design and Hazards Analysis for Offshore Production Facilities-Second Edition Recommended Practice For Classification of Locations For Electrical Installations Sizing, Selection, and Installation of Pressure-Relieving Devices in Refineries; Part I - Sizing and Selection-Seventh Edition and Part II Installation Pressure-relieving and Depressuring Systems-Fifth Edition; Incorporates Errata: 6/2007 and Addendum: 5/2008 Electrical Installations in Petroleum Processing Plants Manual on Installation of Refinery Instruments and Control Systems Design, Construction, Operation, and Maintenance of Offshore 13.D-4

API 5L API 6D API 500 API 520

API 521 API 526 API 527 API 589 API 598 API 607 API 609 API 614 API 620 API 653 API 2000 API/PIP 582 API MPM CH 2.2B

API RP2A API RP 6F API RP 14C

API RP 14G API RP 14J API RP 500 API RP 520

API RP 521 API RP 540 API RP 550 API RP 1111

WEAVER'S COVE ENERGY WEAVERS COVE OFFSHORE BERTH PROJECT Resource Report 13

API RP 2003 API LRFD RP2A API RP 550 API RP 2350 API Standard 12D API Standard 12F API Standard 601 API Standard 620 API Standard 650 API Standard 660 API Pub 2030

Hydrocarbon Pipelines (Limit State Design) - Third Edition, (1997) Protection Against Ignitions Arising Out of Static, Lightning and Stray Currents, 1991 Planning, Designing and Constructing Fixed Offshore Platforms -Load and Resistance Factor Design Article 2, Section 1 Analyzers Overfill Protection for Storage Tanks In Petroleum Field Welded Tanks for Storage of Production Liquids Shop Welded Tanks for Storage of Production Liquids Metallic Gaskets Design and Construction of Large, Welded, Low Pressure Storage Tanks Welded Steel Tanks for Oil Storage Shell and Tube Heat Exchangers for General Refinery Services Guidelines for Application of Fixed Water Spray Systems for Fire Protection in the Petroleum Industry

10.0

ASCE AMERICAN SOCIETY OF CIVIL ENGINEERS Minimum Design Loads for Buildings and Other Structures Wind and Seismic

5E1/ASCE 7-02

11.0

ASME AMERICAN SOCIETY OF MECHANICAL ENGINEERS

Boiler and Pressure Vessel Code, including Mandatory Addenda ASME B1.1 Unified Inch Screw Threads (UN and UNR Thread Form) ASME B1.20.1 Pipe Threads, General Purpose (Inch) ASME B16.5 Pipe Flanges and Flanged Fittings ASME B16.21 Nonmetallic Flat Gaskets For Pipe Flanges ASME B16.25 Buttwelding Ends ASME B16.34 Valves Flanged, Threaded and Welding End ASME B16.47 Series A 150# through 900# 26 Inch through 60 Inch ASME B31.1 Power Piping ASME B31.3 Process Piping, 1993 ASME B31.5 Refrigeration Piping ASME B31.8 Gas Transmission and Distribution Piping Systems ASME B32.3 Piping Systems ASME B46.1 Surface Texture, Surface Roughness, Waviness and Lay Process Piping ASME PTC 25 Pressure Relief Devices ASME PTC 25.3 Safety and Relief Valves ASME Section II Material Specifications: Part A (Ferrous), Part B (Nonferrous), Part C (Weld Filler Metal), Part D (Properties) ASME Section V Non-Destructive Examination ASME, Section VIII Boiler and Pressure Vessel Code, Divisions 1 and 2, and Alternative Rules 13.D-5

WEAVER'S COVE ENERGY WEAVERS COVE OFFSHORE BERTH PROJECT Resource Report 13

ASME Section IX

Boiler and Pressure Vessel Code - Qualification Standard for Welding and Brazing Procedures, Welders, Braziers, and Welding and Brazing Operators

12.0

ASME/ANSI AMERICAN NATIONAL STANDARDS INSTITUTE

13.0

ASNT AMERICAN SOCIETY FOR NONDESTRUCTIVE TESTING Standard for Qualification and Certification of Nondestructive Testing Personnel

ASNT 2504

14.0

ASTM AMERICAN SOCIETY FOR THE TESTING OF MATERIALS Specification for General Requirements for Rolled Steel Plates, Shapes, Sheet Piling, and Bars for Structural Use Specification for General Requirements for Steel Plates for Pressure Vessels Specification for Structural Steel Specification for Gray Iron Castings Specification for Pipe, Steel, Black and Hot-Dipped, Zinc Coated, Welded and Seamless Specification for Steel Wire, Plain, for Concrete Reinforcement Test Method for Weight (Mass) of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings Specification for Carbon Steel Forgings for Piping Applications Specification for Zinc (Hot-Galvanized) Coatings on Products Coatings on Iron and Steel Products Specification for Electric-Fusion (Arc) - Welded Steel Pipe (NPS 4 and over) Practice for Safeguarding Against Embrittlement of Hot-Dip Galvanized Structural Steel Products and Procedure for detecting Embrittlement Specification for Zinc Coating (Hot Dip) on Iron and Steel Hardware Specification for Stainless and Heat-Resisting Chromium - Nickel Steel Plate, Sheet and Strip Specification for Forged or Rolled Alloy Steel Pipe Flanges, Forged Fittings and Valves and Parts for High-Temperature Service Specification for Alloy-Steel and Stainless Steel Bolting Materials for High-Temperature Service Specifications for Carbon and Alloy Steel Nuts for High-Pressure of High-Temperature Service, or Both Specification for Steel Castings, Carbon, Suitable for Fusion Welding, for High-Temperature Service Specification for Steel Casting, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for High-Temperature Service Standard Specification for Piping Fittings of Wrought Carbon Steel and 13.D-6

ASTM A6/A6M ASTM A20/A2OM ASTM A36/A36M ASTM A48/A48M ASTM A53/A53M ASTM A82 ASTM A90/90M ASTM A105/A105M ASTM A123/A123M ASTM A139/A139M ASTM A143/A143M ASTM A153/A153M ASTM A167 ASTM A182/A182M ASTM A193/A193M ASTM A194/A194M ASTM A216/A216M ASTM A217/A217M ASTM A234

WEAVER'S COVE ENERGY WEAVERS COVE OFFSHORE BERTH PROJECT Resource Report 13

ASTM A245 ASTM A252 ASTM A283 ASTM A307 ASTM A320 ASTM A325 ASTM A328 ASTM A366 ASTM A350 ASTM A351 ASTM A352 ASTM A370 ASTM A384 ASTM A385 ASTM A403 ASTM A416 ASTM A420 ASTM A449 ASTM A463 ASTM A490 ASTM A493 ASTM A516/A516M ASTM A525 ASTM A536 ASTM A553/A553M ASTM A577/A577M ASTM A563 ASTM A572

Alloy Steel for Moderate and High Temperature Service For Sheet Metal Used in the Steelwork Standard Specification for Welded and Seamless Steel Pipe Piles Standard Specification for Low and Intermediate Tensile Strength Carbon Steel Plates Carbon Steel Externally Threaded Standard Fasteners Specification for Carbon and Low-Alloy Steel Forgings, Requiring Notch Toughness Testing for Piping Components Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength Standard Specification for Steel Sheet Piling Standard Specification for Steel, Sheet, Carbon, Cold-Rolled Commercial Quality Standard Specification for Carbon and Low-Alloy Steel Forgings, Requiring Notch Toughness testing for Pipe Components Specification for Castings, Austenitic, Austenitic-Ferric (Duplex), for Pressure-Containing Parts Standard Specification for Steel Castings, Ferritic and Martensitic for Pressure-Containing Parts, Suitable for Low-Temperature Service Test Methods and Definitions for Mechanical Testing of Steel Products Standard Practice for Safeguarding Against Warpage and Distortion during Hot-Dip Galvanizing of Steel Assemblies Standard Practice for Providing High-Quality Zinc Coatings (Hot-Dip) Standard Specification for Wrought Austenitic Stainless Steel Piping Fittings Standard Specification for Steel Strand, Uncoated Seven-Wire for Prestressed Concrete Standard Specification for Pipe Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service Quenched and Tempered Steel Bolts and Studs Steel Sheet, Aluminum-Coated, by the Hot Dip Process (1989) Heat-Treated Steel Structural Bolts; 150 PSI Minimum Tensile Strength Stainless and Heat Resisting Steel for cold Heading and Cold Forging Bar and Wire Specification for Pressure Vessel Plates, Carbon Steel, for Moderateand lower- temperature service Standard Specifications for General Requirements for Steel Sheet, Zinc-Coated (Galvanized) By the Hot-Dip Process Ductile iron Castings Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered 8 and 9 percent Nickel Specification for Ultrasonic Angle-beam Examination of Steel Plates Carbon and Alloy Steel Nuts Standard Specification for High-Strength Low- Alloy Columbium Vanadium Structural Steel 13.D-7

WEAVER'S COVE ENERGY WEAVERS COVE OFFSHORE BERTH PROJECT Resource Report 13

ASTM A615 ASTM A706 ASTM A722 ASTM A780 ASTM A786 ASTM A992 ASTM B3 ASTM B8 ASTM B117 ASTM B209 ASTM B496 ASTM B633 ASTM C31 ASTM C33 ASTM C39 ASTM C42 ASTM C94 ASTM C127 ASTM C136 ASTM C140 ASTM C143 ASTM C150 ASTM C165 ASTM C171 ASTM C172 ASTM C177

Standard Specifications for Deformed and Plain Billet-Steel Bars for Concrete Reinforcement Standard Specification for Low-Alloy Steel Deformed Bars for Concrete Reinforcement Uncoated High-Strength Steel Bar for Prestressing Concrete Practice for Repair of Damaged Hot-Dip Galvanized Coatings Rolled Steel Floor Plates Standard Specification for Steel for Structural Shapes for Use in Building Framing Soft or Annealed Copper Wire Standard Specification for Concentric-Lay-Stranded Copper Conductors, Hard, Medium-Hard, or Soft Standard Practice for Operating Salt Spray (Fog) Apparatus Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate Compact Round Concentric-Lay-Stranded Copper Conductors Electro Deposited Coatings of Zinc on Iron and Steel Making and Curing Concrete Test Specimens in the Field Standard Specification for Concrete Aggregates Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens Standard Test Method for Obtaining and Testing Drilled Cores and Sawed Beams of Concrete Standard Test Method for Specific Gravity and Absorption of Coarse Aggregate Sieve Analysis of Fine and Coarse Aggregates Standard Test Methods for Sampling and Testing Concrete Masonry Units and Related Units Slump of Hydraulic Cement Concrete Portland Cement Test Method for Measuring Compressive Properties of Insulations Sheet Materials for Curing Concrete Sampling Freshly Mixed Concrete Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus Standard Specification for Mineral Fiber Thermal Insulating Cement Cold Applied. Tape Coatings for Exterior of Special Sections, Connections, and Fittings for Buried/Submerged Steel Water Pipelines Standard Specification for Air-Entraining Admixtures for Concrete Test Method for Density of Preformed Block-Type Thermal Insulation Liquid Membrane-Forming Compounds for Curing Concrete Cellular Glass Block Insulation for Hot Surfaces to 600 F Class I Mineral Wool Glass Block Standard Specification for Mineral Fiber Hydraulic-Setting Thermal 13.D-8

ASTM C195 ASTM C217 ASTM C260 ASTM C303 ASTM C309 ASTM C343 ASTM C392 ASTM C449

WEAVER'S COVE ENERGY WEAVERS COVE OFFSHORE BERTH PROJECT Resource Report 13

ASTM C476 ASTM C494 ASTM C520 ASTM C535 ASTM C552 ASTM C533 ASTM C549 ASTM C591 ASTM C618 ASTM C795 ASTM C1107 ASTM C1116 ASTM D75 ASTM D226 ASTM D256 ASTM D422 ASTM D429 ASTM D621 ASTM D659 ASTM D698 ASTM D714/714 ASTM D1140 ASTM D1186 ASTM D1535 ASTM D1556 ASTM D1557 ASTM D1622 ASTM D1654 ASTM D1692 ASTM D2000 ASTM D2167 ASTM D2244 ASTM D2487

Insulating and Finishing Cement Specification for Grout Standard Specification for Chemical Admixtures for Concrete Standard Test Method for Density of Granular Loose Fill Insulations Standard Test Method for Resistance to Degradation of Large-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine Cellular Glass Block and Pipe-Thermal Insulation Standard Specification for Calcium Silicate Block and Pipe Thermal Insulation Perlite Loose Fill insulation Unfaced Preformed Rigid Cellular Polyisocyanurate Thermal Insulation Fly Ash and Raw or Calcined; Natural Pozzolan for Use as a Mineral Admixture in Portland Cement Concrete Standard Specification for Thermal insulation for Use in Contact with Austenitic Stainless Steel Packaged Dry, Hydraulic-Cement Grout (Non-shrink) Fiber-Reinforced Concrete and Shotcrete Standard Practice for Sampling Aggregates Standard Specification for Asphalt-Saturated Organic Felt Used in Roofing and Waterproofing Impact Resistance of Plastics and Electrical Insulating Materials Particle-Size Analysis of Soils Standard Test Methods for Rubber Property - Adhesion to Rigid Substrates Compressive Properties of Rigid Cellular Plastics Method for Evaluating Degree of Chalking of Exterior Paints Test Method for Moisture-Density Relations of Soils and Soil-Aggregate Mixtures Using 5.5 pound Rammer and 12 inch Drop Standard Test Method for Evaluating Degree of Blistering of Paint Amount of Material in Soils Finer than the No. 200 Sieve Method fob Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to a Ferrous Base Standard Method for Specifying Color by the Munsell System Density and Unit Weight of Soil in Place by the Sand-Cone Method Laboratory Compaction Characteristics of Soil Using Modified Effort 56,000 ft-lb/cu. ft. Density Apparent or Rigid Cellular Plastics Method for Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments Rate of Burning and/or Extent and Time of Burning of Cellular Plastics Using a Specimen Supported by a Horizontal Screen Classification System for Rubber Products in Automotive Applications Density and Unit Weight of Soil in Place by the Rubber Balloon Method Test Method for Calculating of Color Differences from Instrumentally Measured Color Coordinates Classification of Soils for Engineering Purposes (Unified Soil 13.D-9

WEAVER'S COVE ENERGY WEAVERS COVE OFFSHORE BERTH PROJECT Resource Report 13

ASTM D2856 ASTM D2922 ASTM D2937 ASTM D3017 ASTM D3487 ASTM D3786

ASTM D4318 ASTM D4354 ASTM D4355 ASTM D4533 ASTM D4632 ASTM D4751 ASTM D4759 ASTM D4945 ASTM D5519 ASTM D6092 ASTM D6684 ASTM E84 ASTM E96 ASTM E376 ASTM F436 ASTM F112187

Classification System) Open Cell Content of Rigid Cellular Plastics by the Air Pycnometer Density of Soil-Aggregate in Place by Nuclear Methods (Shallow Depth) Density of Soil in Place by the Drive-Cylinder Method Water Content of Soil and Rock in Place by Nuclear Methods (Shallow Depth) Specification for Mineral Insulating Oil Used in Electrical Apparatus Standard Test Method for Hydraulic Bursting Strengths of Knitted Goods and Non-woven Fabrics - Diaphragm Bursting Strength Tester Method Liquid Limit, Plastic Limit, and Plasticity Index of Soils Standard Practice for Sampling Geosynthetics for Testing Standard Test Method for Deterioration of Geotextiles from Exposure to Ultraviolet Light (Xenon-Arc Type Apparatus) Standard Test Method for Trapezoidal Tearing Strength of Geotextiles Standard Test Method for Grab Breaking Load and Elongation of Geotextiles Standard Test Method for Determining Apparent Opening Size of a Geotextile Standard Practice for Determining the Specification Conformance of Geosynthetics Standard Test Method for High-Strain Dynamic Testing of Piles Standard Test Method for Particle Size Analysis of Natural and ManMade Riprap Materials Standard Practice for Specifying Standard Sizes of Stone for Erosion Control Standard Specification for Materials and Manufacture of Articulating Concrete Block (ACB) Revetment Systems Test Method for Surface Burning Characteristics of Building Materials Water Vapor Transmission of Materials Sheet Form Standard Practice for Measuring Coating Thickness by Magnetic-Field or Eddy-Current (Electromagnetic) Examination Methods Hardened Steel Washers Standard Specification for International Shore Connections for Marine Fire Applications (1993)

15.0

AWS AMERICAN WELDING SOCIETY SPECIFICATIONS Welding Symbols Standard Symbols for Welding, Brazing, and Nondestructive Examination Standard Welding Terms and Definitions Standard Procedure for Calibrating Magnetic Instruments to Measure Delta Ferrite Content of Austenitic and Duplex Austenitic-Ferritic Stainless Steel Weld Metal Specification for Nickel and Nickel Alloy Welding Electrodes for Shield 13.D-10

AWS A2.1 AWS A2.4 AWS A3.0 AWS A4.2

AWS A5.11

WEAVER'S COVE ENERGY WEAVERS COVE OFFSHORE BERTH PROJECT Resource Report 13

AWS A5.14 AWS D1.1 AWS D1.4 AWS D3.6 16.0 AWWA

Metal Arc Welding Specification for Nickel and Nickel Alloy Bare Welding Electrodes and Rod Structural Welding Code - Steel Structural Welding Code - Reinforcing Steel Specification for Underwater Welding AMERICAN WATER WORKS ASSOCIATION AWWA Standard for Steel Water Pipe EUROPEAN COMMITTEE FOR ELECTRICAL STANDARDIZATION

AWWA C200 17.0 CENELEC

18.0

CINI

INSULATION FOR INDUSTRIES

19.0

CAA

CLEAN AIR ACT National Emission Standard for Hazardous Air Pollutants

CAA Section 12 20.0

CGA COMPRESSED GAS ASSOCIATION Standard for Insulated Cargo Tank Specification for Nonflammable Cryogenic Liquids

CGA 341

21.0

CMAA CRANE MANUFACTURERS ASSOCIATION OF AMERICA Electric Overhead Traveling Cranes CONCRETE REINFORCING STEEL INSTITUTE MANUAL OF

CMAA 70 22.0 29.0 CRSI PRACTICE

CRSI 63 CRSI 65

Recommended Practice for Placing Reinforcing Bars Recommended Practice for Placing Bar Supports, Specifications and Nomenclature CSA AMERICA, INC Shutdown System Adopting Latest Standards and Supporting Codes ELECTRICAL AND ELECTRONIC MANUFACTURERS OF CANADA Procedure for Testing the Resistance of Metal-clad Switchgear Under 13.D-11

23.0

CSA

CSA for Class 1 Div 2 24.0 EEMAC

EEMAC G14-1

WEAVER'S COVE ENERGY WEAVERS COVE OFFSHORE BERTH PROJECT Resource Report 13

Condition of Arcing Due to an Internal Fault 25.0 EJMA STANDARDS OF THE EXPANSION JOINT MANUFACTURERS ASSOCIATION

26.0

EPA

ENVIRONMENTAL PROTECTION AGENCY Monitoring Requirements FLUID CONTROL INSTITUTE INC. Control Valve Seat Leakage FEDERAL STANDARDS (Rev B) Colors FACTORY MUTUAL APPROVAL GUIDE (Shutdown System Adopting Latest Standards and Supporting Codes)

EPA 40 CFR Part 61 27.0 FCI

FCI 70-2 28.0 FED-STD

FED-STD 595 29.0 FM

FM for Class 1 Div 2 30.0 FS

FEDERAL SPECIFICATIONS (Rev A; Am 1) Bearings, Ball, Annular (General Purpose) (Basic; Am 4) Bearings, Roller, Cylindrical; and Bearings, Roller, Self and Aligning (Rev D) Chains and Attachments, Welded and Weldless (Rev D Am 1) Wire Rope and Strand GAS PROCESSORS ASSOCIATION Obtaining Natural Gas Samples

FS FF-B-171 FS FF-B-185 FS RR-C-271 FS RR-W-410 31.0 GPA

GPA 2166

32.0

GIIGNL

LNG CUSTODY TRANSFER HANDBOOK

33.0

ICEA INSULATED CABLE ENGINEERS ASSOCIATION (NEMA WC8) Ethylene-Propylene-Rubber-insulated Wire and Cable for the Transmission and Distribution of Electrical Energy (NEMA WC57) Control Cables

ICEA S-68-516 ICEA 5-73-532

13.D-12

WEAVER'S COVE ENERGY WEAVERS COVE OFFSHORE BERTH PROJECT Resource Report 13

34.0

IEC

INTERNATIONAL ELECTROTECHNICAL COMMISSION Industrial Platinum Resistance Thermometer Sensors Industrial-Process Control Valve, Part 1: Control Valve Terminology and General Conditions Industrial-Process Control Valves, Part 2-1: Flow-Capacity, Sizing Equations for Fluids Flow Under Installed Conditions Industrial-Process Control Valves, Part 2-3: Flow Capacity, Test Procedures Industrial-Process Control Valves, Part 2: Flow Capacity, Section 4: Inherent Flow Characteristics and Rangeability Industrial-Process Control Valves, Part 3-1: Dimensions-Face-to-Face Dimensions for Flanged, Two-Way, Globe-Type, Straight Pattern and Centre-Control Valves Industrial-Process Control Valves, Part 3-2: Dimensions-Face-to-Face Dimensions for Rotary Control Valves Except Butterfly Valves Industrial-Process Control Valves, Part 3: End-to-End Dimensions for Buttweld, Two-Way Globe-Type, Straight Pattern Control Valves Industrial-Process Control Valves, Part 4: Inspection Routine Testing Industrial Process Control Valves, Part 5, Marking Industrial Process Control Valves, Part 6, Mounting Details for Attachment of Positioners to Control Valves, Section 1: Positioner Mounting on Linear Actuators Industrial Process Control Valves, Part 8, Noise Considerations, Section 2: Laboratory Measurement of Noise Generated by Hydrodynamic Flow through Control Valves Industrial Process Control Valves, Part 8, Noise Considerations, Section 8: Control Valves, Prediction of Noise Generated by Hydrodynamic Flow Functional Safety of Electrical/Electronic/Programmable Electronic Safety-Related Systems Safety Instrumented Systems for the Process Industry Sector

IEC 751 IEC 60534-1 Part 1 IEC 60534-2-1 IEC 60534-2-3 IEC 60534-2-4 IEC 60534-3-1

IEC 60534-3-2 IEC 60534-3-3 IEC 60534-4-4 IEC 60534-5 IEC 60534-6-1

IEC 60534-8-2

IEC 60534-8-3

IEC 615078 SIL 3 IEC 61511 35.0

IEEE INSTITUTE OF ELECTRICAL AND ELECTRONIC ENGINEERS Flame Testing of Cables for Use in Cable Tray in Industrial and Commercial Occupancies Type Test of Class 1E Electric Cables, Field Splices, and Connections for Nuclear Power Generating Stations Standard for Petroleum and Chemical Industry - Severe Duty Totally Enclosed Fan Cooled (TEFC) Squirrel Cage Induction Motors - Up to and Including 500 Horsepower National Electrical Safety Code Code for Electrical Metering Standard Rating Structure for AC High-Voltage Circuit Breakers Rated on a Symmetrical Current Basis 13.D-13

IEEE 1202 IEEE 383 IEEE 841

IEEE C2 IEEE C12.1 IEEE C37.04

WEAVER'S COVE ENERGY WEAVERS COVE OFFSHORE BERTH PROJECT Resource Report 13

IEEE C37.06 IEEE C37.13 IEEE C37.20.1 IEEE C37.20.2 IEEE C37.23 IEEE C37.40

IEEE C37.60

IEEE C57.104 IEEE C57.111 IEEE C57.12.00 IEEE C57.12.13 IEEE C57.12.80 IEEE C57.12.90

IEEE C57.13 IEEE C57.13.1 IEEE Std. 1 IEEE Std. 80 IEEE Std 142 IEEE Std. 519 IEEE Std. 837 IEEE Std. 998 36.0 ISA 20 ISA 75.01 ISA 75.03 ISA 75.04 ISA

AC High-Voltage Circuit Breakers Rated on a Symmetrical Current Basis -- Preferred Ratings and Related Required Capabilities Low-Voltage AC Power Circuit Breakers Used in Enclosures Metal-Enclosed Low-Voltage Power Circuit-Breaker Switchgear Standard for Metal-Clad and Station-Type Cubicle Switchgear Standard for Metal-Enclosed Bus and Calculating Losses in IsolatedPhase Bus Service Conditions and Definitions for High-Voltage Fuses, Distribution Enclosed Single-Pole Air Switches, Fuse Disconnecting Switches, and Accessories Standard for Overhead, Pad-Mounted, Dry Vault, and Submersible Automatic Circuit Reclosers and Fault Interrupters for Alternating Current Systems Up to 38 kV Guide for the Interpretation of Gases Generated in Oil Immersed Transformers (ANSI) Guide for Acceptance of Silicone Insulating Fluid and Its Maintenance in Transformers Standard General Requirements for Liquid-Immersed Distribution, Power, and Regulating Transformers Liquid-Filled Transformers Used In Unit installations Including Unit Substations Conformance Standard Standard Terminology for Power and Distribution Transformers (ANSI) Standard Test Code for Liquid-Immersed Distribution, Power, and Regulating Transformers; and Guide for Short-Circuit Testing of Distribution and Power Transformers (ANSI) Standard Requirements for Instrument Transformers Field Testing of Relaying Current Transformers General Principles for Temperature Limits in the Rating of Electrical Equipment and for the Evaluation of Electrical Insulation AC Substation Grounding Grounding of Industrial and Commercial Power Systems (Lightning Protection) Recommended Practices and Requirements for Harmonic Control in Electrical Power Systems Qualifying Permanent Connections Used in Substation Grounding Guide for Direct Lightning Strike Shielding of Substations

THE INSTRUMENTATION, SYSTEMS AND AUTOMATION SOCIETY Specification Forms for Process, Measurement and Control Instruments, Primary Elements, and Control Valves Flow Equations for Sizing Control Valves Face-to-Face Dimensions for Integral Flanged Globe-Style Control Valve Bodies (ANSI Classes 125, 150, 250, 300 and 600) Face-to-Face Dimensions for Flangeless Control Valves (ANSI Classes 150, 300 and 600) 13.D-14

WEAVER'S COVE ENERGY WEAVERS COVE OFFSHORE BERTH PROJECT Resource Report 13

ISA 75.08.04 ISA 75.08.07 ISA 75.15 ISA 75.16 ISA 75.17 ISA 75.19.01 ISA 75.22 ISA 75.25 ISA S5.1 ISA S5.3 ISA S84 ISA S91 ISA-RP-12.1 ISA-RP-12.4 37.0 ISO

Face-to-Face Dimensions for Buttweld-End Globe-Style Control Valves (ANSI Classes 4500) Face-to-Face Dimensions for Separable Flanged Globe-Style Control Valves (ANSI Classes 150, 300 and 600) Face-to-Face Dimensions for Buttweld-End Globe-Style Control Valves (ANSI Classes 150, 300, 600, 900, 1500 and 2500) Face-to-Face Dimensions for Flanged Globe-Style Control Valve Bodies (ANSI Classes 900, 1500 and 2500) Control Valve Aerodynamic Noise Prediction Hydrostatic Testing of Control Valves Face-to-Centerline Dimensions for Flanged Globe-Style Angle Control Valve Bodies (ANSI Classes 150, 300 and 600) Test Procedure for Control Valve Response Measurement from Step Inputs Instrumentation Symbols and Identification Graphics Symbols for Distributed Control/Shared Display Instrumentation, Logic and Computer Systems Shutdown System Adopting Latest Standards and Supporting Codes Shutdown System Adopting Latest Standards and Supporting Codes Electrical Instruments in Hazardous Areas Instrument Purging for Reduction of Hazardous Area Classification INTERNATIONAL ORGANIZATION FOR STANDARDIZATION Petroleum Liquids Automatic Pipeline Sampling Metal Valve for Use in Flanged Pipe Systems Face-to-Face and Center-to-Face Dimensions Refrigerating Light Hydrocarbon Fluids

ISO 3171:1988 ISO 5752 ISO 8943 38.0

MNL 116 MANUAL FOR QUALITY CONTROL FOR PLANTS AND PRODUCTION OF PRECAST AND PRESTRESSED CONCRETE PRODUCTS

39.0

MS

MILITARY SPECIFICATIONS (Rev A; Amt) Cranes, Overhead Traveling, Underhung, Electric Powered (Rev C; Am 2, Notice 1) Varnish, Moisture-and-Fungus Resistant (for Treatment of Communications, Electronics, and Associated Equipment)

MS MIL-C-28546 MS MIL-V-173

40.0

MSS MANUFACTURERS' STANDARDIZATION SOCIETY OF THE VALVE AND FITTING INDUSTRY Standard Marking System for Valves, Fittings, Flanges and Unions Quality Standard for Steel Castings and Forgings for Valves, Flanges 13.D-15

MSS SP-25 MSS SP-53

WEAVER'S COVE ENERGY WEAVERS COVE OFFSHORE BERTH PROJECT Resource Report 13

MSS SP-54

MSS SP-55

MSS SP-67 MSS SP-68 MSS SP-93

MSS SP-94

and Fittings and Other Piping Components Magnetic Particle Examination Method Quality Standard for Steel Castings and Forgings for Valves, Flanges and Fittings and Other Piping Components Radiographic Examination Method Quality Standard for Steel Castings and Forgings for Valves, Flanges and Fittings and Other Piping Components Visual Method for Evaluation of Surface Irregularities Butterfly Valves High Pressure Offset Seat Butterfly Valves Quality Standard for Steel Castings and Forgings for Valves, Flanges and Fittings and Other Piping Components Liquid Penetrant Examination Method Quality Standard for Steel Castings and Forgings for Valves, Flanges and Fittings and Other Piping Components Ultrasonic Examination Method

41.0

NACE NATIONAL ASSOCIATION OF CORROSION ENGINEERS Sulfide Stress Cracking Resistant Metallic Materials for Oil Field Equipment Control of External Corrosion on Underground or Submerged Metallic Piping Systems Design Consideration for Corrosion Control of Reinforcing Steel in Concrete Structure Coatings for Concrete Surfaces in Non-Immersion and Atmospheric Service Visual Standard for Surfaces of New Steel Air-blast Cleaned with Abrasive NATIONAL ASSOCIATION OF CORROSION

NACE MR-01-75 NACE RP0169 NACE RP0187 NACE RP0591 NACE TM-0170

42.0

NACE/INTERNATIONAL ENGINEERS

RP-0188 PIP Coatings PIP CTCE-1000 PIP CTSE-1000 43.0

Discontinuity (Holiday) Testing of New Protective Coatings on Conductive Substrates Process Industry Practices External Coating Systems Selection Criteria Application of External Coatings

NEMA NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION Enclosures for Electric Equipment (1000 Volts maximum) Busways Enclosed and Miscellaneous Distribution Equipment Switched (600 Volts Maximum) 13.D-16

NEMA 250 NEMA BU 1 NEMA KS 1

WEAVER'S COVE ENERGY WEAVERS COVE OFFSHORE BERTH PROJECT Resource Report 13

NEMA ICS 1 NEMA ICS 2 NEMA ICS 3 NEMA ICS 4 NEMA ICS 6 NEMA MG 1 NEMA SG-5 NEMA ST 1 NEMA WC26 44.0 51.0 NFPA

Industrial Control and Systems General Requirements industrial Control and Systems Controllers, Contactors, and Overload Relays Rated Not More Than 2000 Volts AC or 750 Volts DC Industrial Control and Systems Factory Built assemblies Industrial Control and Systems Terminal Blocks Industrial Control and Systems Enclosures Motors and Generators Power Switchgear assemblies Specialty Transformers (Except General Purpose Type) Wire and Cable Packaging NATIONAL FIRE PREVENTION ASSOCIATION Portable Fire Extinguishers Standard for Water Spray Fixed Systems for Fire Protection Standard for the Installation of Standpipe and Hose Systems Standard for Dry Chemical Extinguishing System Firewater Pumps Private Firewater Systems Flammable Liquids Code Fire Prevention in Use of Cutting and Welding Processes, 1994 Standard for the Production, Storage and Handling of LNG, 1994 National Electric Code (NEC) Fire Alarm Code Lightning Protection Code Life Safety Code Fire Tests of Building Construction and Materials, 1990 Method of Test of Surface Burning Characteristics of Building Materials Standard For Purged and Pressurized Enclosures For Electrical Equipment in Hazardous Areas

NFPA 10 NFPA 15 NFPA 14 NFPA 17 NFPA 20 NFPA 24 NFPA 30 NFPA 51B NFPA 59A NFPA 70 NFPA 72 NFPA 78 NFPA 101 NFPA 251 NFPA 255 NFPA 496

45.0

OCIMF OIL COMPANIES INTERNATIONAL MARINE FORUM

Design and Construction Specification for Marine Loading Arms Fire Protection for Marine Terminals Prediction of Wind and Current Loads on VLCCs Safety Guide for Terminals Handling Ships Carrying Liquefied Gases in Bulk Prediction of Wind loads on Large Liquefied Gas Carriers International Safety Guide for Oil Tankers and Terminals 46.0 OCMA FSV.1 FIRE SAFE CONSTRUCTION FOR BALL VALVES

13.D-17

WEAVER'S COVE ENERGY WEAVERS COVE OFFSHORE BERTH PROJECT Resource Report 13

47.0

OSHA OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION

OSHA 1910.95 Occupational Noise Exposure Regulation OSHA 29 CFR1910. Flammable Liquids 106 OSHA 29 CFR1910. Fire Alarm Systems 165 48.0 PCI PRECAST/PRESTRESSED CONCRETE INSTITUTE Precast and Prestressed Concrete PROCESS INDUSTRY PRACTICES, PIPING, LATEST EDITION External Coating Systems Selection Criteria Application of External Coatings

MNL-120-99 49.0 PIP

PIP CTCE-1000 PIP CTSE-1000 50.0

SIGTTO SOCIETY OF INTERNATIONAL GAS TANKER & TERMINAL OPERATORS

A Guide to Contingency Planning for Marine Terminals Handling Liquefied Gases in Bulk Guidelines for Hazard Analysis as an Aid to Management of Safe Operations Ship/Shore Interface Communications Recommendations and Guidelines for Linked Ship/Shore Emergency Shut-Down of Liquefied Gas Cargo Transfer Guidelines for the Alleviation of Excessive Surge Pressures on ESD Liquefied Gas Handling Principles on Ships and in Terminals Fire Protection for Marine Terminals Prediction of Wind Loads on Large Liquefied Gas Carriers, 1995 SIGTTO/OCIMF Listing of Design Guidelines for Liquefied Gas Terminals 51.0 SSPC STEEL STRUCTURE PAINTING COUNCIL STANDARDS Mineral and Slag Abrasives Shop, Field and Maintenance Painting Measurement of Dry Coasting Thickness with Magnetic Gages Solvent Cleaning Hand Tool Cleaning Power Tool Cleaning White Metal Blast Cleaning Commercial Blast Cleaning Brush-off Blast Cleaning Near-White Blast Cleaning 13.D-18

SSPC - AB1 SSPC PA1 SSPC - PA-2 SSPC - SP-1 SSPC - SP-2 SSPC - SP-3 SSPC - SP-5 (NACE No.1) SSPC - SP-6 (NACE No. 3) SSPC - SP-7 (NACE No. 4) SSPC - SP-10(NACE

WEAVER'S COVE ENERGY WEAVERS COVE OFFSHORE BERTH PROJECT Resource Report 13

No. 2) SSPC SP-11 SSPC-VIS 1&3

Power Tool Cleaning to Bare Metal Pictorial Surface Preparation Standards for Abrasive Blast and Power/Hand Tool Cleaned Steel

52.0

TEMA TUBULAR EXCHANGER MANUFACTURER ASSOCIATION

Standards for Finned Tube Type Exchangers (Vaporizers) 53.0 TUV APPROVAL TO LEVEL AK-6 SHUTDOWN SYSTEM ADOPTING LATEST STANDARDS AND SUPPORTING CODES

54.0

UBC-1997 UNIFORM BUILDING CODE (SEISMIC) OR FEMA PUBLICATION 368 NEHRP 2000, USE IN CONJUNCTION WITH 14

55.0

UFC

UNIFORM FIRE CODE

56.0

UL

UNDERWRITERS LABORATORIES, INC. Fire Resistance Directory Standard for Safety - Cabinets and Boxes Shutdown System Adopting Latest Standards and Supporting Codes Electric Motors and Generators for Use in Hazardous (Classified) Locations Standard for Motor Control Centers Busways and associated Fitting2s Medium-Voltage Power Cables Standard for Safety for Electrical Power and Control Tray Cables with Optional Optical-Fiber Members Standard for Safety Metal-Enclosed Low-Voltage Power Circuit Breaker Switchgear Metal-Clad Cables

UL 05 UL 50 UL UL 508 UL 674 UL 845 UL 857 UL 1072 UL 1277 UL 1558 UL 1569 57.0

AIDS TO NAVIGATION (ATONS)

References 1. United States Coast Guard COMDTINST M16500.1C Aids to Navigation Positioning Manual COMDTINST M16500.3A Aids to Navigation Technical Manual COMDTINST M16500.7 Aids to Navigation Administration Manual COMDTINST M16500.21 Aids to Navigation Seamanship Manual. COMDTINST M16510.2A Aids to Navigation Visual Signal Design Manual 13.D-19

WEAVER'S COVE ENERGY WEAVERS COVE OFFSHORE BERTH PROJECT Resource Report 13

2. United States of America Code of Federal Regulations, Title 33, Navigation and Navigable Waters, Chapter 1 - Coast Guard, Department of Homeland Security, Part 62 United States Aids to Navigation System 3. ASTM D25 Standard Specification for Round Timber Piles 4. AWPA C3 Standard Specification for CCA Treatment
58.0 STEEL SHEET PILING

References Design of Sheet Pile Walls (Technical Engineering and Design Guides as Adapted from the U.S. Corps of Engineers, No. 15) D3.6 Specification for Underwater Welding 59.0 CERTAIN OTHER CODES, STANDARDS, SPECIFICATIONS AND GUIDELINES

Permanent International association of Navigation Congresses "Guidelines for the Design of Fender Systems", 2002 46 CFR Part 154, Safety Standards for Self-propelled Vessels Carrying Bulk Liquefied Gases 49 CFR Part 191, Transportation of Natural and Other Gas by Pipeline; Annual Reports, Incident Reports, and Safety-Related Condition Reports 49 CFR Part 192, Transportation of Natural and Other Gas by Pipeline: Minimum Federal Safety Standards 49 CFR Part 193, Liquefied Natural Gas Facilities: Federal Safety Standards 49 CFR Part 195, Transportation of Hazardous Liquids by Pipeline 49 CFR Part 199, Drug and Alcohol Testing. U.S. Army Corps of Engineers. 2002. Coastal Engineering Manual. Engineer Manual 1110-21100, U.S. Army Corps of Engineers, Washington, D.C. (in 6 Volumes). U.S. Army Corps of Engineers. 1995. Designs of Coastal Revetments, Seawalls, and Bulkheads. Engineer Manual 1110-2-1614, U.S. Army Corps of Engineers, Washington, D.C., misc. paginated. Center for Civil Engineering Research and Codes. 1995. Manual on the Use of Rock in Hydraulic Engineering. CUR/RWS Report 169, A.A. Balkema Publishers, Brookfield, VT.

13.D-20