100

NOTES:

ABBREVIATIONS: 1. ALL DIMENSIONS ARE IN MILLIMETRES AND LEVELS ARE IN

METRES UNLESS NOTED OTHERWISE.
RHS - RECTANGULAR HOLLOW SECTION
2. THIS DRAWING IS PRODUCED ON BASIS OF INFORMATION
℄ - CENTER LINE FROM RECORD DRAWINGS PROVIDED BY NATIONAL
EXISTING mm - MILLIMETRES HIGHWAYS, CONTRACTOR SHALL CONFIRM AT SITE THAT THE
HAND - RAILS PROPOSED DETAILS SUCH AS DIMENSIONS AND LOCATION OF
TYP. - TYPICAL
HOLES WILL FIT INTO THE EXISTING STRUCTURE.
Millimetres

CONTRACTOR SHALL INFORM THE DESIGNER IN CASE OF ANY

DISCREPANCY.

3. DEFECTS AT ACCESS STEPS ARE BASED ON FINDINGS OF

LAST GENERAL INSPECTION ON 17/JULY/2020. PROPOSED
TYPICAL REPAIRS TO BE FOLLOWED AT OTHER STEPS WITH
SIMILAR DEFECTS.

4. SEVERAL OTHER DEFECTS SUCH AS CORROSION TO OTHER

STEEL ELEMENTS, MISSING FIXINGS ETC. WERE RECORDED
AND ARE NOT COVERED UNDER THIS PROPOSAL.
10

100 5. AN APPROPRIATE ANTI-SLIP AND PROTECTIVE COATING

CUT LINE SHOWN INDICATIVELY
CONFORMING TO BS EN 16165 SHALL BE PROVIDED ON
0

EXISTING STEEL STAIR TREAD PROPOSED TREADS.

DO NOT SCALE

WITH DEFECTS (5mm THICK)

6. HOLES ON PROPOSED ELEMENTS SHALL BE CAREFULLY
KEY PLAN A1/88.60 DRILLED TO ENSURE CORRECT ALIGNMENT FOR
MAIN STRINGER BEAM
(SCALE 1 : N.T.S) WYBOSTON FOOTBRIDGE INSTALLATION OF HEXAGONAL BOLTS.
152.4x101.6x6.35mm
GRID REF: 516400E 256480N
RHS

1830 (TILL THE INNER FACE OF

STRINGER AT OTHER END) STEPS:
BEFORE INSTALLATION CAREFULLY CHECK THAT THE
1. CUT THE EXISTING DEFECTIVE STEPS AT 120mm FROM THE INNER FACE OF DIMENSION OF THE PROPOSED ELEMENTS AND
EXISTING STRINGER USING AN APPROPRIATE METHOD SUCH AS DISC-CUTTER POSITION OF THE HOLES SHALL FIT IN PROPERLY OVER
OR FLAME CUTTING. THE EXISTING SYSTEM BY TAKING SITE MEASUREMENTS

2. SURFACE PREPARATION USING ANGLE GRINDER OR SAND PAPER MAY BE

VIEW A - A (HANDRAILS NOT SHOWN FOR CLARITY, REQUIRED AT FACES OF EXISTING TREAD AND STRINGER TO ENSURE
PROPER FITTING OF THE PROPOSED ELEMENTS.
SIMILAR FIXING DETAILS TO BE PROVIDED AT THE
OTHER END OF THE EXISTING STEP WITH DEFECTS)

SAFETY, HEALTH AND ENVIRONMENTAL

STAGE-1 INFORMATION
SCALE 1:5 In addition to the hazards/risks normally associated with the types of work
detailed on this drawing, note the following significant residual risks
(Reference shall also be made to the design hazard log).
Construction
1) SAFETY RISKS DUE TO USE OF POWER TOOLS FOR CUTTING
MAIN STRINGER BEAM EXISTING TREAD
152.4x101.6x6.35mm RHS 2) DIFFICULTY IN INSTALLATION DUE TO INCORRECT ALIGNMENT
STEPS:
OF HOLES
3) DIFFICULTY IN INSTALLATION DUE TO TIGHT CLEARANCES
1. APPROPRIATE SIZE HOLES IN ACCORDANCE WITH
4) DAMAGE TO EXISTING STEEL MEMBERS WHILE DRILLING HOLES
THE MANUFACTURER'S SPECIFICATIONS TO BE DRILLED INTO
Maintenance / Cleaning
EXISTING RHS STRINGER BEAMS AT THE PROPOSED LOCATIONS
TO INSTALL M10 (SIZE 1) HOLLO-BOLTS.
℄ OF EXISTING NONE
TREAD / PROPOSED
UNEQUAL ANGLE
2. PROPOSED UNEQUAL ANGLE (WITH PRE-DRILLED HOLES) TO BE Use
FIXED WITH THE STRINGER USING M10 (SIZE-1) HOLLO-BOLTS NONE
APPLYING REQUIRED TIGHTENING TORQUE IN ACCORDANCE
B-
WITH THE MANUFACTURER'S SPECIFICATIONS.
Decommissioning / Demolition
100
A
-
50 40 75 75 40
NONE

MAIN STRINGER BEAM Description

25
152.4x101.6x6.35mm
RHS 2 NO. PRE-DRILLED HOLES FOR Status Revision Drawn Checked Reviewed Authorised Issue Date
M12 HEXAGONAL BOLTS (TYP.)

75
50
A
-
PROPOSED 2 NO.
33°
Description

M-10 (SIZE-1) 30 95 105

Status Revision Drawn Checked Reviewed Authorised Issue Date
B

15
HOLLO-BOLTS

2
230 PROPOSED UNEQUAL ANGLES
SECTION LOSS DUE TO - Description
100mmx75mmx8mm
CORROSION
SHOWN INDICATIVELY PROPOSED UNEQUAL ANGLE Status Revision Drawn Checked Reviewed Authorised Issue Date
(SEE NOTE 03) 100mmx75mmx8mm MAIN STRINGER BEAM
EXISTING STAINLESS STEEL BASE
EXISTING STEEL PLATE PLATE WITH 2 NO. M20 152.4x101.6x6.35mm Description
(5mm THK.) WITH HOLDING-DOWN BOLTS (TYP.) RHS
UPSTAND/DOWNSTAND Status Revision Drawn Checked Reviewed Authorised Issue Date
AT FREE EDGES
Description
VIEW A - A VIEW B - B
STAGE-2 Status
S0
Revision
P01.1
Drawn
---
Checked
---
Reviewed
---
Authorised
---
Issue Date
---
SCALE 1:5
Drawing Suitability Status

WORK IN PROGRESS S0
Woodcote Grove
TYPICAL ISOMETRIC VIEW OF THE EXISTING STAIRCASE AT NORTH WEST END STEPS: Ashley Road
Epsom

PLATE USING M-12

6mm THICK STEEL
SCALE: N.T.S 1. PLACE THE PROPOSED STEEL TREAD TO ALIGN THE POSITION OF HOLES AT BOTH ENDS Surrey

HEXAGON BOLTS
KT18 5BW
2. INSTALL 2 NO. M12 HEXAGONAL BOLTS TO FIX THE PROPOSED PLATE C 20 Tel: +44 (0)1372 726140
Fax: +44 (0)1372 740055
℄ OF EXISTING -
Copyright C SNC Lavalin (2022) www.atkinsglobal.com
TREAD / PROPOSED

6
PROPOSED MATERIAL SPECIFICATIONS :
UNEQUAL ANGLE Client

65

65

65
1. M-12 NON-PRELOADED HEXAGONAL HEAD FULLY-THREADED CARBON STEEL BOLTS (MIN. LENGTH OF 60mm)

6
HAVING PROPERTY CLASS 8.8 AND CONFORMING TO BS EN ISO 4014:2011 SHALL BE USED.
287
2. HEXAGONAL CARBON STEEL NUTS CONFORMING TO BS EN ISO 4032:2012 SHALL BE USED. 72 150 65
PROPOSED 6mm THICK MILD STEEL

150

150

150
287

287

287
3. HOLLO-BOLTS SHALL BE M10 (SIZE-1) WITH PROPRIETARY ELECTRO-ZINC PLATED COATING FROM AN PLATE FIXED WITH 2 Nos. M-12 40 75 75 40
APPROVED MANUFACTURER.THE MINIMUM FACTORED TENSION AND SHEAR RESISTANCE SHALL BE 8.5KN AND HEXAGONAL BOLTS AT EACH END 50 50
10KN RESPECTIVELY.
25

Project Title
Civil Engineering Specialist Support
4. MECHANICAL PROPERTIES OF FASTENERS SHALL BE CONFORMING TO BS EN ISO 898-1:2013.
75

72

72

72
50

5. PROPOSED MILD STEEL PLATE SHALL BE GRADE S275JR OR S275J0 AND CONFORMING TO BS EN - 10025. Drawing Title

6
6
DIMENSIONAL TOLERANCES SHALL BE CONFORMING TO BS EN - 10029. 33°
30 95 105 55 A1/88.60 WYBOSTON FOOTBRIDGE
15

6. PROPOSED UNEQUAL ANGLE SHALL BE GRADE S275JR OR S275J0 AND CONFORMING TO BS EN - 10025. 1830
2

DIMENSIONAL TOLERANCES SHALL BE CONFORMING TO BS EN - 10056. 230 PROPOSED UNEQUAL ANGLES PROPOSED REPAIRS FOR
100mmx75mmx8mm C ACCESS STEPS
PLAN - SECTION C-C
MAIN STRINGER BEAM
152.4x101.6x6.35mm
Drawing Number
RHS PROPOSED 6mm THICK MILD STEEL PLATE (SEE NOTE 5) Project Originator Volume

HE605560 - ATK - SBR -

VIEW B - B XX_BX5281 - DR - CB - 000001
STAGE-3 Location Type Role Number
SCALE 1:5 Original Project
Size: A1 Scale: AS SHOWN Ref. No: 55 Sheet: 1 of 1 Rev: P01.1
This Drawing is saved on ProjectWise. Plotted: 03/11/2022 17:11:17 By: SELV3604