AirHarmony-4000 Datasheet

High-Capacity Outdoor LTE-Advanced eNodeB

AirHarmony-4000 is part of Airspan’s carrier-class LTE Advanced eNodeB

family. AirHarmony 4000 is a Macro-class product that supports 3GPP’s
Long Term Evolution (LTE) eNodeB specifications, providing high-speed
data, mobility, Voice over LTE, and broadcast/multicast services to meet the
demands of the LTE Mobile Carriers.

AirHarmony-4000 is a compact, easy to install Macro-class eNodeB, allowing

an operator to deploy LTE broadband services using existing infrastructure
or Street Furniture. AirHarmony 4000 has two 43dBm transmit channels and
two receive channels. AirHarmony-4000 supports single carrier up to
20MHz.

Release 10 LTE-Advanced
AirHarmony-4000 supports 3GPP LTE Broadband access technologies; Airspan’s 3GPP LTE
implementation is compliant with the 3GPP standards and has interoperable S1 and X2 interfaces
and supports commercial GCF tested UE devices, including Smartphones, Dongles and Tablet
computers.

Broadband Access

AirHarmony-4000 supports 3GPP LTE Broadband access technologies; Airspan’s 3GPP LTE implementation is compliant with the 3GPP
standards and has interoperable S1 and X2 interfaces and supports commercial GCF tested UE devices, including Smartphones, Dongles
and Tablet computers.

Page 1 of 6
 AirHarmony-4000 Datasheet
Physical
Dimensions

Variant Dimensions1 (H x W x D)
Main Unit w/o / duplexers 509 x 236 x 210 mm / 20.0 x 9.3 x 8.3 in.
Main Unit with integrated external duplexers 631 x 236 x 267 mm / 24.8 x 9.3 x 10.5 in.
Weight

Variant Weight
Main Unit w/o filters / duplexers 17Kg/37.48 Lbs.
External Duplexers 10 Kg / 22 Lbs.
Main Unit with integrated external duplexers 27 Kg / 59.52 Lbs.
Universal mounting bracket 3 Kg / 6.6 Lbs.

Operational Tolerances
Type Details Standard Compliance
Operating temperature -40°C to 55°C / -40°F to 131°F ETSI 300 019 1-4
Operating humidity 5% - 100% non-condensing ETSI 300 019 1-4
Storage temperature -40°C to 70° C / -40°F to 158°F N/A
Storage humidity 5% - 100% non-condensing ETSI 300 019 1-4
Rain and dust ingress protection IP66 N/A
70-106 kPa as well as:
Operational altitude From -60m to 1800m @ 40C ETSI 300 019 1-4
From 1800m to 4000m @ 30C
Solar radiation 1120 W/m2 ETSI 300 019 1-4

Voltages and Amperage Draws

AirHarmony 4000 AC variants supports direct connection to AC power source
• Operational Voltage Range: 90VAC~240VAC, 50Hz~60Hz
AirHarmony 4000 DC variants supports direct connection to DC power source
• Operational Voltage Range: -40.5 to -57 VDC
• Transient Voltage: +150V (ETR283)
AC power feed is also available, using an AC/DC power converter offered by Airspan.

Tx Power PoE Maximum

Max Power Power Supply
at Power Power
Duplex Consumption Requirements
RF Port Source Consumption
(W) (W)
(dBm)
(W)
FDD 2x 43 DC 300 60 500

Transmitter Radio Performance

Product Variants

1
Dimensions excludes connectors height and protruding screws
Page 2 of 6
 AirHarmony-4000 Datasheet

Band Variant Downlink Uplink Dup. Max Tx / Rx Tx Power Filters /

Freq. Freq. Mode Chann Conf. Power Source Duplexers
(MHz) (MHz) el BW (dBm) Variant
(MHz)
Integrated
20 HAR40-CN-U20-B06DP 791-821 832-862 FDD 20 2x2 43 DC External
Duplexers

Channel Frequency Resolution

The center frequency is tunable with a 100 KHz resolution
Frequency Stability
The AirHarmony-4000 reference frequency accuracy is better than ±0.05ppm
Modulation & FEC
AirHarmony 4000 supports QPSK, 16QAM and 64QAM modulations on both Downlink and Uplink
and 256QAM in Downlink. All Modulation and Coding Schemes defined in 3GPP TS 36.211.
Power
Maximum Configurable Tx Power (per RF port) 43 dBm
Transmit Power Accuracy ±1dB in normal conditions
Control Step 1dB
Transmitter Dynamic Range
The transmitter supports a monotonic power control of 40dB with step size of 1dB
Transmitter Spurious Emissions
AirHarmony-4000 complies with the “Category B” transmitter spurious emissions, as they are defined in TS
36.104
Transmitter Error Vector Magnitude
The AirHarmony 4000 transmitter EVM/RCE3 is no more than -28dB for all power levels
Receiver Radio Performance
Receiver Sensitivity Level2
The values in the table below are defined for QPSK ⅓ with allocation BW as indicated by TS 36.104
Channel Bandwidth (MHz) Allocation Size (RB) Reference Sensitivity Level (dBm)
5 25 -102.5
10 25 -102.5
15 25 -102.5
20 25 -102.5

In Channel Selectivity3
AirHarmony-4000 complies with ICS as defined by TS 36.104 for “Wide Area BS”

2
The receiver sensitivity power level is the minimum mean power received at the antenna connector at which a throughput
requirement is being met for a specified reference measurement channel. The AirHarmony 4000 meets the requirements defined for in
TS 36.104 for Wide Area Base Stations
3 In-channel selectivity (ICS) is a measure of the receiver ability to receive a wanted QPSK½ signal at its assigned resource block

locations in the presence of an interfering signal received at a larger power spectral density.
Page 3 of 6
AirHarmony-4000 Datasheet
Adjacent Channel Selectivity4
AirHarmony-4000 ACS complies with ACS requirements as defined in TS 36.104 for “Wide Area BS”
Receive Dynamic Range
AirHarmony-4000’s receiver has a dynamic range of 54dB

Maximum Input Signal

The AirHarmony-4000 receiver can receive a maximum on-channel signal of –30dBm
Maximum Input Signal without Damage
The AirHarmony-4000 receiver can tolerate a maximum signal of -10dBm without damage
Receiver Spurious Emission5
AirHarmony-4000 complies with the receiver spurious emission as defined by TS 36.104 as well as ETSI EN 301 893
Mobility
AirHarmony-4000 can support Intra and Inter frequency handovers.
Physical Interfaces
This following defines all external Network and Maintenance equipment interfaces
as well as System LED.
All interfaces are Weatherproof, supporting IP66 Ingress Protection Rating.
GPS Antenna Port
Connector Type TNC Male
Characteristic Impedance 50 Ω
Quantity 1

RF ports:
• 4 ports located on the top panel and connected via cables to the external
duplexers.
• Duplexers and cables connecting them are factory installed
• RF ports to the antenna located on the duplexers one on the top and one on
the bottom
Connector Type 4.1-9.5 DIN Female
Characteristic Impedance 50 Ω

Fiber SFP Port

Connector Type SFP Socket with Full AXS sealing connector
Quantity 2
Protocol Ethernet, GPON (without sync over GPON)

Copper Ethernet Port

Connector Type RJ45

4
Adjacent Channel Selectivity (ACS) is defined as the measure of the receiver’s ability to receive a wanted signal at its assigned
channel frequency in the presence of an adjacent channel signal with a specified center frequency offset of the interfering signal to the
band edge of a victim system

5
The spurious emissions are the power of emissions generated or amplified in a receiver that appear at the receiver antenna
connector
Page 4 of 6
AirHarmony-4000 Datasheet
Standard IEEE802.3
Cable Type STP Category 5E
Interface Speed 100/1000 Base-T
Communication Mode Full/Half Duplex with Auto Negotiation
PoE Output 2 ports support PoE out
Quantity 2

PoE Port Specification

Power available at powered device 25.5 W
Maximum power delivered 30 W6
Voltage range delivered 50.0–57.0 V
Voltage range (at powered device) 42.0–57.0 V
Maximum current 600 mA
Maximum cable resistance 12.5 Ω (Category 5 cable)
Power management Four power class levels negotiated at initial
connection or 0.1 W steps negotiated continuously
Supported cabling Category 3 and Category 5

SBA Control
Connector Type AISG
Standard RS485
Controls the SBA direction when mounted remotely
Can also control specific RET antennas control by the AISG protocol. Contact
Airspan sales for further details.

Power Connection DC Variants

Connector Type Proprietary
Standard -48V DC
Cable Length Various
LED Display
A single tri-color LED (Green/Red/Orange) appears at the bottom of the unit, providing unit status indication

Mounting
AirHarmony-4000 includes a pole mounting kit with the following attributes:
Attribute Values
Mechanical tilting range 0°
Supported pole diameters 48.3 to 406.4 mm / 1.9 to 16 inches
Supported wind load 200 km/h / 125 mph

6
Each port can supply up to 30W. Total power from the 2 ports cannot exceed 45W
Page 5 of 6
AirHarmony-4000 Datasheet

Standard Compliances
Standard
EN 301 489-1 V1.9.2 (2011-09) Class B
EMC EN 301 489-4 V2.2.1 (2015-05)
FCC 47 CFR Part 15:2014 Subpart B Class B
IEC 60950-1:2005 + A1:2009 + A2:2013
IEC 60950 22:2005 (1st Edition) + A11:2008
EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013
Safety
EN 60950-22:2006 + A11:2008
UL 60950-1
UL 60950-22
ROHS EU ROHS directive - 2002/95/EC (ROHS) - ROHS6
WEEE Per the requirements of European directive 2002/96/EC
IEC 60529
IEC 60068
Environmental ETSI EN 300-019-2-4 Operational (non-weather protected equipment)
ETSI EN 300-019-2-1 Storage (weather protected, not temperature-controlled locations)
ETSI EN 300-019-2-2 Transportation (Public Transportation)
IP Rating IP66

Color – RAL9002

Page 6 of 6