New MG ZS EV Owner Manual

CONTENTS
Preface................................................................................................................................ 1
Introduction .................................................................................................................................... 1
The Owner's Handbook ......................................................................................................................................................... 1
Status at Time of Printing ....................................................................................................................................................... 1
Warranty and Service .............................................................................................................................................................. 1
Symbols Used ............................................................................................................................................................................ 2
In an Emergency........................................................................................................................................................................ 3
Vehicle Identification Information................................................................................................ 4
Vehicle Identification ................................................................................................................................................................ 4
Vehicle Identification Label ..................................................................................................................................................... 5
Instructions for Use of Electric Vehicle........................................................................................ 7
Effects of Ambient Temperature ........................................................................................................................................... 7
Instructions for High Voltage Battery Pack Recycling ...................................................................................................... 7
Driving Range............................................................................................................................................................................. 8
Equalisation Charging............................................................................................................................................................... 9
Intelligent Charging................................................................................................................................................................... 9
Crash Outage Control .......................................................................................................................................................... 10
High Voltage System............................................................................................................................................................... 10
Precautions in the Event of an Accident ........................................................................................................................... 12
1
CONTENTS
1 Instruments and Controls ........................................................................................... 13
Instruments and Controls ........................................................................................................... 14
Instrument Pack ........................................................................................................................... 16
Information Centre ...................................................................................................................... 18
Warning Lights and Indicators.................................................................................................... 28
Lights and Switches...................................................................................................................... 40
Master Lighting Switch........................................................................................................................................................... 40
Headlamp Levelling Manual Adjustment............................................................................................................................ 42
Main Beam Switch................................................................................................................................................................... 43
Direction Indicator Switch ................................................................................................................................................... 46
Fog Lamp Switch ..................................................................................................................................................................... 46
Hazard Warning Lamp........................................................................................................................................................... 47
Wipers and Washers.................................................................................................................... 48
Windscreen Wiper Operation ............................................................................................................................................ 48
Rear Window Wiper Operation ........................................................................................................................................ 50
Steering System ........................................................................................................................... 52
Adjustment of Steering Column.......................................................................................................................................... 52
Electric Power Steering ......................................................................................................................................................... 52
2
CONTENTS
Horn............................................................................................................................................... 54
Rearview Mirrors .......................................................................................................................... 55
Exterior Door Mirrors ......................................................................................................................................................... 55
Manual Anti-dazzle Interior Rearview Mirror.................................................................................................................. 57
Sunvisor ........................................................................................................................................ 58
Windows........................................................................................................................................ 59
Window Operation................................................................................................................................................................ 59
Sunroof * ........................................................................................................................................ 62
Instructions ............................................................................................................................................................................. 62
Sunroof Operation ................................................................................................................................................................ 63
Interior Light ............................................................................................................................... 68
Power Socket ................................................................................................................................ 69
Front Power Socket ............................................................................................................................................................... 69
Rear USB Ports ....................................................................................................................................................................... 70
Top USB Port........................................................................................................................................................................... 70
Wireless Charging System for Mobile Phones * ........................................................................ 72
Wireless Charging of Mobile Phones................................................................................................................................. 72
Storage Devices ............................................................................................................................ 74
3
CONTENTS
Instructions .............................................................................................................................................................................. 74
Glove Box................................................................................................................................................................................. 74
Centre Console Armrest Box ............................................................................................................................................ 75
Loadspace ................................................................................................................................................................................. 75
Cup Holder ................................................................................................................................... 77
Centre Console Cup Holder .............................................................................................................................................. 77
Roof Luggage Rack * ..................................................................................................................... 78
Maximum Authorised Load for the Roof.......................................................................................................................... 78
Periodical Check ..................................................................................................................................................................... 78
2 Air Conditioning and Audio Systems ........................................................................ 79
Ventilation .................................................................................................................................... 80
A/C Filter.................................................................................................................................................................................. 81
Vents ......................................................................................................................................................................................... 81
A/C Control Panel ....................................................................................................................... 83
Control Panel........................................................................................................................................................................... 83
A/C Control Shortcut ........................................................................................................................................................... 83
Defrost/Demist ...................................................................................................................................................................... 83
Heated Rear Window .......................................................................................................................................................... 84
4
CONTENTS
Blower Speed Control Button............................................................................................................................................. 84
Temperature Control Button............................................................................................................................................... 84
A/C Control Interface .................................................................................................................. 85
Control Interface - Connected Car * ................................................................................................................................. 85
Control Interface - Non Connected Car * ....................................................................................................................... 86
Temperature Control............................................................................................................................................................. 87
Cooling On/Off ....................................................................................................................................................................... 87
Auto Mode ............................................................................................................................................................................... 87
System On/Off......................................................................................................................................................................... 87
Blower Speed Control........................................................................................................................................................... 87
Air Distribution Mode ........................................................................................................................................................... 87
Air Circulation Mode............................................................................................................................................................. 88
Infotainment System * ................................................................................................................. 90
Important Safety Information............................................................................................................................................... 90
Privacy and Data Sharing....................................................................................................................................................... 91
Cautions for Using Screen.................................................................................................................................................... 91
Basic Operations..................................................................................................................................................................... 92
Bluetooth Phone ..................................................................................................................................................................... 97
Entertainment........................................................................................................................................................................100
5
CONTENTS
Vehicle-Mobile Phone Interconnection............................................................................................................................106
Energy Management .............................................................................................................................................................107
MG Touchpoint .....................................................................................................................................................................107
Vehicle Setting........................................................................................................................................................................107
Setting......................................................................................................................................................................................108
3 Seats & Restraints ...................................................................................................... 111
Seats............................................................................................................................................. 112
Overview ................................................................................................................................................................................112
Head Restraints.....................................................................................................................................................................112
Front Seats ............................................................................................................................................................................113
Rear Seats...............................................................................................................................................................................115
Front Seat Heating * .............................................................................................................................................................116
Seat Belts .................................................................................................................................... 117
Protection Provided by Seat Belts ....................................................................................................................................117
Wearing Seat Belts................................................................................................................................................................119
Children and Seat Belts ......................................................................................................................................................123
Seat Belt Pre-tensioners......................................................................................................................................................124
Seat Belt Checks, Maintenance and Replacement.........................................................................................................125
Airbag Supplementary Restraint System ................................................................................ 128
6
CONTENTS
Overview ................................................................................................................................................................................128
Airbag Deployment ..............................................................................................................................................................129
Conditions in Which Airbags Will Not Deploy ............................................................................................................132
Disabling the Passenger Airbag..........................................................................................................................................133
Service and Replacement of Airbags ................................................................................................................................135
Disposal of Airbags...............................................................................................................................................................136
Child Restraints .......................................................................................................................... 137
Important Safety Instructions about Using Child Restraints ......................................................................................137
Child Restraints Groups......................................................................................................................................................140
Approved Child Restraint Positions .................................................................................................................................142
4 Starting & Driving ...................................................................................................... 147
Keys .............................................................................................................................................. 148
Overview ................................................................................................................................................................................148
Replacing the Battery...........................................................................................................................................................149
Child Proof Locks ....................................................................................................................... 151
Alarm System ............................................................................................................................. 152
Power Immobilisation ..........................................................................................................................................................152
Body Anti-theft System .......................................................................................................................................................153
7
CONTENTS
Tailgate.....................................................................................................................................................................................158
Starting and Stopping the Power System................................................................................ 160
START STOP Switch ............................................................................................................................................................160
READY Mode.........................................................................................................................................................................161
Switching the Power System OFF.....................................................................................................................................163
Pedestrian Alert Control System ............................................................................................ 164
Economical and Environmental Driving .................................................................................. 165
Running-in...............................................................................................................................................................................165
Economic Driving..................................................................................................................................................................165
Driving in Special Environment..........................................................................................................................................166
Check and Service ................................................................................................................................................................167
Charging and Discharging Requirements ................................................................................ 168
Charging Your Vehicle at Home ........................................................................................................................................170
Installed Charging Points.....................................................................................................................................................170
Home Charging Guide.........................................................................................................................................................170
Charging and Medical Condition Awareness .................................................................................................................171
Charging Port ........................................................................................................................................................................171
Electric Charging Identifier Label * ...................................................................................................................................173
Rapid Charging ......................................................................................................................................................................175
8
CONTENTS
Slow Charging........................................................................................................................................................................176
Charging Information ...........................................................................................................................................................179
Equalisation Charging...........................................................................................................................................................180
Charging Times .....................................................................................................................................................................180
Discharging .............................................................................................................................................................................184
Electric Drive Transmission....................................................................................................... 186
Instructions ............................................................................................................................................................................186
Gear Shift Control................................................................................................................................................................186
Driving on Hills .....................................................................................................................................................................189
Driving Mode .........................................................................................................................................................................189
Energy Regeneration............................................................................................................................................................191
Energy Management .............................................................................................................................................................192
Protection Mode...................................................................................................................................................................193
Brake System .............................................................................................................................. 195
Electronic Brake Force Distribution (EBD) ....................................................................................................................195
Electronic Brake Assistance (EBA) ...................................................................................................................................196
Anti-lock Brake System (ABS) ...........................................................................................................................................196
Hill Hold Control (HHC) ...................................................................................................................................................197
Hill Descent Control (HDC) .............................................................................................................................................198
9
CONTENTS
Auto Hold...............................................................................................................................................................................199
Active Rollover Protection (ARP).....................................................................................................................................201
Emergency Braking Hazard Warning Lights Control (HAZ) ......................................................................................201
Multi-Collision Brake System (MCB) ...............................................................................................................................202
Stability Control System and Traction Control System...............................................................................................203
Electronic Parking Brake (EPB)..........................................................................................................................................204
Adaptive Cruise Control System.............................................................................................. 206
Adaptive Cruise Control System Activation .................................................................................................................206
Adaptive Cruise Target Speed Adjustment ...................................................................................................................209
Adaptive Cruise Target Following Distance Adjustment ............................................................................................209
Adaptive Cruise Pause/Standby .........................................................................................................................................210
Automatic Deactivation of Adaptive Cruise .................................................................................................................210
Adaptive Cruise Override .................................................................................................................................................210
Adaptive Cruise Resume ...................................................................................................................................................211
Clear Speed Memory ..........................................................................................................................................................211
Adaptive Cruise Control System Impairment and Ineffectiveness ............................................................................211
Special Driving Environments ...........................................................................................................................................211
Parking Aid System.................................................................................................................... 215
Ultrasonic Sensor Parking Aid...........................................................................................................................................215
10
CONTENTS
360 Around View System ...................................................................................................................................................217
Rear Driver Assistance System * .............................................................................................. 218
System Overview .................................................................................................................................................................218
Switching the System Functions On/Off ........................................................................................................................220
System Functions .................................................................................................................................................................220
Tyre Pressure Monitoring System (TPMS).............................................................................. 224
Driving Assist System ................................................................................................................ 225
Description of Front View Camera .................................................................................................................................225
Description of Front Detection Radar ...........................................................................................................................226
Speed Assist System ............................................................................................................................................................227
Lane Assist System ..............................................................................................................................................................232
Traffic Jam Assist System.....................................................................................................................................................235
Forward Collision System .................................................................................................................................................238
Load Carrying ............................................................................................................................. 242
Loadspace Loading................................................................................................................................................................242
Internal Loading.....................................................................................................................................................................242
General Towing Safety .........................................................................................................................................................243
5 Emergency Information ............................................................................................ 245
11
CONTENTS
Hazard Warning Devices........................................................................................................... 246
Warning Triangle ...................................................................................................................................................................246
eCall - SOS Emergency Assistance .......................................................................................... 247
Emergency Starting ................................................................................................................... 250
Vehicle Recovery......................................................................................................................... 252
Towing for Recovery............................................................................................................................................................252
Transporter or Trailer .........................................................................................................................................................255
Tyre Repair .................................................................................................................................. 256
Tool Identification ................................................................................................................................................................257
Tyre Repair ............................................................................................................................................................................257
Changing a Wheel * ..............................................................................................................................................................260
Fuse Replacement ...................................................................................................................... 264
Fuse ..........................................................................................................................................................................................264
Fuse Box .................................................................................................................................................................................264
Passenger Compartment Fuse Box ..................................................................................................................................265
Front Compartment Fuse Box ..........................................................................................................................................268
Bulb Replacement ...................................................................................................................... 271
Bulb Specification..................................................................................................................................................................271
Bulb Replacement .................................................................................................................................................................272
12
CONTENTS
6 Maintenance ............................................................................................................... 279
Maintenance................................................................................................................................ 280
Routine Servicing ..................................................................................................................................................................280
Bonnet ......................................................................................................................................... 283
Opening the Bonnet.............................................................................................................................................................283
Closing the Bonnet...............................................................................................................................................................283
Bonnet Open Warning ........................................................................................................................................................283
Front Compartment .................................................................................................................. 285
Cooling System .......................................................................................................................... 286
Coolant Check and Top Up ..............................................................................................................................................286
Coolant Specification...........................................................................................................................................................286
Brake............................................................................................................................................ 288
Brake pads ..............................................................................................................................................................................288
Brake Fluid Check and Top Up..........................................................................................................................................288
Brake Fluid Specification .....................................................................................................................................................289
Battery......................................................................................................................................... 290
Battery Maintenance ...........................................................................................................................................................290
Battery Replacement ..........................................................................................................................................................291
13
CONTENTS
High Voltage Battery Pack ........................................................................................................ 292
Precautions and restricted conditions for use of battery ...........................................................................................292
Washer ....................................................................................................................................... 294
Washer Fluid Check and Top Up .....................................................................................................................................294
Washer Nozzles....................................................................................................................................................................295
Wipers ......................................................................................................................................... 296
Wiper Blades .........................................................................................................................................................................296
Replacing Front Wiper Blades ..........................................................................................................................................297
Replacing Rear Wiper Blades ...........................................................................................................................................298
Tyre .............................................................................................................................................. 299
Overview ................................................................................................................................................................................299
Caring for your Tyres...........................................................................................................................................................300
Tyre Wear Indicators ...........................................................................................................................................................301
Tyre Rotation.........................................................................................................................................................................302
Tyre/Snow Chains .................................................................................................................................................................304
Cleaning and Vehicle Care......................................................................................................... 305
Exterior...................................................................................................................................................................................305
Cleaning the Interior............................................................................................................................................................308
14
CONTENTS
7 Technical Data ............................................................................................................ 311
Technical Data Dimensions ....................................................................................................... 312
Weights........................................................................................................................................ 314
Towing Weights .....................................................................................................................................................................315
Towing Bar Dimensions.......................................................................................................................................................316
Parameters of Traction Motor .................................................................................................. 318
Recommended Fluids and Capacities ...................................................................................... 319
Wheel Alignment (Unladen Condition) .................................................................................. 320
Wheels and Tyres ....................................................................................................................... 320
Tyre Pressure (Cold) .................................................................................................................. 320
8 Appendix ..................................................................................................................... 321
Removable Tow Bar ................................................................................................................... 322
Tow Bar Operating Instructions........................................................................................................................................322
15
PREFACE
Introduction consequences thereof, including loss or damage to
property, or injury to persons, can be accepted by the
The Owner's Handbook manufacturer or MG Authorised Repairer who supplied
This handbook describes all of the vehicles and standard the publication, except in respect of personal injury caused
equipment specification within the model range. Some of by the negligence of the manufacturer or MG Authorised
the information therefore, may not apply to your particular Repairer .
car.
Warranty and Service
Always remember that if you have any queries concerning
the operation or specification of your car, your MG Please consult the owners section at www.mg.co.uk for
Authorised Repairer will be glad to advise you. the warranty terms and conditions, warranty statement,
exemptions and service item renewal schedule.
The illustrations in the Owner's Handbook are for
reference only.
The information presented in this manual may vary slightly
depending on vehicle configuration, software version and
sales area.
Status at Time of Printing

MG operates a policy of constant product improvement
and therefore reserves the right to change specifications
without notice at any time. Whilst every effort is
made to ensure complete accuracy of the information
in this publication, no liabilities for inaccuracies or the
1
PREFACE
Symbols Used
This symbol indicates that parts described must be
The following symbols used within the handbook call your disposed of by authorised persons or bodies to protect the
attention to specific types of information. environment.
Warning Asterisk
This warning symbol identifies procedures An asterisk (*) appearing within the text, identifies features
that must be followed precisely, or or items of equipment that are either optional, or are only
information that must be considered with fitted to some vehicles in the model range.
great care, in order to reduce the risk of
personal injury or serious damage to the car. Illustration Information
Identifies components being explained.

Important
IMPORTANT Identifies movement of components being
explained.
The statements stated here must be followed strictly,
otherwise your car could be damaged.
Note
Note: This describes helpful information.
2
PREFACE
In an Emergency
IMPORTANT
Remember the breakdown safety code

If a breakdown occurs while travelling:
• Wherever possible, consistent with road safety and
traffic conditions, the car should be moved off the
main thoroughfare, preferably into a lay-by. If a
breakdown occurs on a motorway, pull well over to
the inside of the hard shoulder.
• Switch on hazard lights.
• If available, position a warning triangle or a flashing
amber light 50 to 150 metres (150 to 500 ft) behind
your vehicle to warn approaching traffic. Note it is a
legal requirement of some countries that a warning
triangle is carried in the vehicle, if in doubt consult
the local highways agency for further information.
• Consider evacuating passengers through nearside
doors onto the verge to reduce risk of injury in the
event of collision.
3
PREFACE
Vehicle Identification Information required to provide the identification numbers of these
assemblies.
Vehicle Identification
Vehicle Identification Location
1
Vehicle Identification Number (VIN)
• On the floor under the front driver seat;
• On the identification plate;
• Stamped on a plate visible through the bottom left hand
corner of the windscreen;
00000000000000000000
00000000000000000000
• On the inner side of the tailgate visible by opening the

00000000000000000000
0000
00000000000000000000
0000
00000000000000000000
0000
00000000000000000000
0000
00000000000000000000
0000
00000000000000000000
0000
00000000000000000000
00000000000000000000
00000000000000000000
00000000000000000000
00000000000000000000
00000000000000000000
00000000000000000000
00000000000000000000
tailgate.
00000000000000000000
Note: The DLC is located in the driver footwell at the

base of the fascia panel on the RH side. The VIN
information can be extracted from the vehicle using
23 the approved diagnostic equipment.
1 Vehicle Identification Number (VIN) Drive Motor Number

2 Drive Motor Number Stamped on the lower part of the drive motor housing.
3 Electric Drive System Number Electric Drive System Number
Always quote the Vehicle Identification Number (VIN) Stamped behind the upper part of the electric drive system
when communicating with MG Authorised Repairer. If the housing.
drive motor or electric drive system is involved, it may be
4
PREFACE
Vehicle Identification Label
The vehicle identification label contains the following
information:
• Type Approval Number;
• Vehicle Identification Number (VIN);
• Gross Vehicle Weight;
• Gross Train Weight;
• Max Front Axle Weight;
• Max Rear Axle Weight;
• Paint Code;
• Trim Code;
5
PREFACE
Location of Vehicle Identification Label
The identification label is located at the lower side of right
pillar B.
000000000000
000000000000
000000000000
000000000000
000000000000
000000000000
000000000000
000000000000
000000000000
000000000000
000000000000
000000000000
6
PREFACE
Instructions for Use of Electric Vehicle approved dismantling agent. Please refer to the following
information and requirements.
Effects of Ambient Temperature • ONLY qualified personnel should work with the high
The working performance of the high-voltage battery voltage system - there is danger of DEATH.
pack fitted to your vehicle is related to the ambient • High voltage safety: the high voltage system fitted to
temperature. This battery powers the vehicle power your vehicle features a HV battery containing high
system and therefore it is recommended that where voltage components such as lithium battery packs
possible the vehicle should be used within the temperature and high voltage wiring harness; DO NOT attempt
range of -15 to 45℃. This will ensure that the vehicle to dismantle any area of this system, suitably trained
is in the optimum working state, and help extend the professional staff must observe insulation safety
service life of the high-voltage battery pack. Extremely protection before working on or near the high voltage
high or low temperatures will affect the performance of system.
the high-voltage battery pack and vehicle. • Transportation: The high-voltage battery pack is
classed as a Category 9 hazardous material and must
Instructions for High Voltage Battery Pack be transported by vehicles qualified in transporting
Recycling Category 9 hazardous materials.
The high-voltage battery pack fitted to your vehicle • Storage: All HV components (including batteries)
contains several lithium based battery cells. It is should be stored at room temperature and in a dry
installed centrally to the motor-vehicle chassis. Arbitrary environment. They must be kept away from dangerous
disposal may cause pollution, hazard and damage to the sources, such as flammable objects, heat and water
environment. The high-voltage battery pack MUST be sources.
recycled by an MG Authorised Repairer or a professional
7
PREFACE
• Internal composition: The high-voltage battery pack • The driving range is related to the rate of discharge. In
consists of lithium batteries (pack), PCB, HV and normal order to avoid a high rate of discharge from affecting
electric wiring, metal casing and other components. the performance of the high-voltage battery pack, it is
It is strongly recommended that the used high-voltage recommended that the vehicle is connected to a suitable
battery pack generated from vehicle scrappage or any charger upon illumination of the low battery warning
other reasons should be disposed of by an MG Authorised lamp in the instrument pack.
Repairer. • The actual driving range of the vehicle will reduce with
the increase of vehicle age.
Note: If you decide not to use the recommended MG
Authorised Repairer to dispose of your high voltage • The use of A/C will reduce the driving range.
battery, the responsibility of the consequences of • The driving range varies at different speeds.
environmental pollution or accidents must be bourne • At low temperatures, the driving range will be reduced
by the owner. due to temperature characteristics of the battery during
use.
Driving Range • In some instances of extreme temperatures and
low battery voltage, you may experience insufficient
The driving range of your vehicle depends on the HV
acceleration or power reduction. This is due to battery
battery condition, quantity of available electricity, vehicle
characteristics.
age (current remaining battery life), weather, temperature,
road conditions and driving habit etc. To help increase the range of the vehicle please observe
the following:
The range can be affected by other electrical loads (such as
• Have the vehicle regularly maintained as per service
A/C, lights etc), driving style and general road conditions.
schedule.
It should be noted that: • Always ensure the tyre pressures are correct.
8
PREFACE
• Try and use the vehicle between the recommended Equalisation Charging
ambient temperatures.
In order to assist in extending the service life of the high
• Do not park or store the vehicle for long periods with voltage battery pack it is recommended that an equalisation
a low state of charge, where possible charge the vehicle charge is carried out at regular intervals.
as soon as possible prior to storage.
• Remove unnecessary articles to reduce the vehicle load. Please see "Equalisation Charging" in the "Starting &
Driving" section.
• Use of high power consuming systems such as A/C
and heating will use large amounts of power. This will
Intelligent Charging
reduce the driving range.
• At a high speed, where possible, close the windows to The 12V battery SOC is constantly monitored, when the
reduce wind resistance and power consumption. Start/Stop switch is in the OFF position it is possible, under
• Try to maintain a steady speed at all times, avoid certain conditions, that the HV battery will automatically
constant acceleration and braking. charge the 12V battery to ensure the vehicle starts. This
function will activate and switch off automatically.
• During acceleration, apply the accelerator pedal as
gently as possible. Note: The system will suspend intelligent charging if a
• During deceleration, release the accelerator pedal; fault is present, when starting or the vehicle is being
under certain conditions when not applying the brake charged by an external device.
or gently applying the brake, the energy regeneration
Note: The driving range will be reduced after
system (KERS) will assist in charging the HV battery
intelligent charging.
and extend the driving range.
Note: The intelligent charging function is suspended
when the high voltage battery is in a low SOC.
9
PREFACE
Crash Outage Control High Voltage System
If a crash or serious impact occurs, a signal from the SDM • The high voltage system used on your
(Airbag Control Module) will disconnect the relays within vehicle features AC and DC voltages
the battery management system isolating the high voltage up to about 438V. All high voltage
battery from the systems on the vehicle. components have warning labels attached
- please observe these warnings and any
requirements when operating within or
close to these areas.
• ONLY qualified personnel should work on,
or with, the high voltage system - there is
danger of DEATH.
10
PREFACE
The high voltage system component layout is shown below:
1 High Voltage Battery (ESS)

2 Electric Heater
3 Electric Drive Transmission
4 Manual Service Disconnect (MSD)
5 Electric A/C Compressor
6 Power Distribution Unit (PDU)
7 HV Battery Heater
8 High Voltage Harness
1 9 Charging Port
2 10 Combined Charging Unit (CCU)
10
3
4
9 8 7 6 5
11
PREFACE
Precautions in the Event of an Accident
• Ensure the vehicle is in P, the parking brake is applied and the vehicle power system is OFF.
• If any cables on the vehicle are exposed, in order to prevent electric shock or even death DO NOT
make any contact with any cable.
• If the vehicle catches fire, and the fire is small and slow, a carbon dioxide extinguisher can be used to
extinguish the fire, and contact the fire services as soon as possible; if the fire is large and spreading
quickly, immediately evacuate the vehicle and contact the fire services immediately.
• If the vehicle is involved in a collision and cannot be re-started, the negative cable of 12V battery and
Manual Service Disconnect (MSD) MUST be disconnected prior to rescue.
• When the vehicle is completely or partially immersed in water, switch off the vehicle power system
and evacuate the car immediately. The negative cable of 12V battery and Manual Service Disconnect
(MSD) MUST be disconnected prior to rescue or as soon as the vehicle is refloated/removed from the
water. Observe the water/vehicle for any abnormal signs such as excessive bubbles or noises, this may
indicate battery short circuit issues. If no signs are evident, there should not be a shock risk from the
bodywork and recovery can commence.
• If your car is being recovered by an independent recovery agent, please contact an MG Authorised
Repairer for guidance.
• The vehicle is supplied with an emergency response information card. Please show the card to the
rescue personnel when they arrive.
12
1
Instruments and Controls
14 Instruments and Controls 69 Power Socket
16 Instrument Pack 72 Wireless Charging System for Mobile
Phones *
18 Information Centre
74 Storage Devices
28 Warning Lights and Indicators
77 Cup Holder
40 Lights and Switches
*
78 Roof Luggage Rack
48 Wipers and Washers
52 Steering System
54 Horn
55 Rearview Mirrors
58 Sunvisor
59 Windows
*
62 Sunroof
68 Interior Light
INSTRUMENTS AND CONTROLS
Instruments and Controls
9 8 7 6 5 4 3 2 1
10 11 12 13 14 15 16 17 18 19
14
1 Power Window Switch 17 Accelerator Pedal 1
2 Wiper Stalk Switch 18 Bonnet Release Handle
3 Horn Button 19 Exterior Rearview Mirror and Headlamp Leveling
Switch
4 Driver Airbag
5 Instrument Pack
6 Indicator/Main Beam Stalk Switch
7 START/STOP Switch
8 Infotainment System
9 Front Passenger Airbag
10 Air Conditioning/Infotainment Control Switch
11 Driving Mode Selection Switch
12 Energy Regeneration Mode Selection Switch
13 Shift Control Knob
14 Battery Power Display Switch
15 Cruise Control Stalk Switch
16 Brake Pedal
15
Instrument Pack
1 2 3 4
100
Volta ge 367 V
Motor S pe e d
Curre nt 0 A
0.0 X1000RP M
mph %powe r
ODO 75 mls
ODO
Current Journey Long Press OK To Reset
0
N N 9N N N -N --- --.-
190 mls P hh mls mph mls/kWh 1 64 %
-2 5
8 7 6 5
1 Speedometer value, it represents that the power system outputs

power to drive the vehicle; If the power is displayed as
2 Warning Lamps and Indicators
a negative value, it represents that the power system
3 Information Centre converts part of the kinetic energy into electrical
4 Power Meter energy.
Indicates the power status of the power drive system 5 Electricity Meter of High-Voltage Battery Pack
as a percentage. If the power is displayed as a positive
16
IMPORTANT 1
• When the high voltage battery power indicator
displays a low charge condition connect to a
charger and charge immediately.
• Before undertaking any journeys please ensure
the high voltage battery contains enough power.
6 Total Mileage
7 Gear Display
8 Range To Empty
17
Information Centre • Press the OK button in the RH steering wheel
multifunction switch pack to confirm or long press the
With the vehicle power system in the ON/READY position, OK button to reset.
the information centre function can be selected as follows: 1 2 3 4
1 Vehicle Information
2 MG Pilot
3 Health Centre
4 Settings
Vehicle Information
Vehicle Information includes:
• Energy Flow: Displays a graphic showing the current
• Press the UP/DOWN/LEFT/RIGHT button in the RH state of power flow.
steering wheel multifunction switch pack, this will • Electrical Information: Displays the current operation
access and display the information centre options. state of the vehicle, including the voltage, current and
• Press the UP/DOWN button in the RH steering wheel motor speed.
multifunction switch pack to cycle through options.
18
• Current Journey: Displays the trip mileage, trip time, Displays the current level and allows adjustment of the 1
average speed and average power consumption since backlight brightness.
vehicle start. It can be reset by long pressing the "OK"
button in the RH steering wheel multifunction switch OverSpeed Threshold
pack. Allows the setting of the over-speed alarm threshold,
• Accumulated Total: Displays the trip mileage, trip time, please note, the over-speed alarm function is turned off
average speed and average power consumption since when "OFF" is displayed.
the last vehicle reset. It can be reset by long pressing
the "OK" button in the RH steering wheel multifunction Warning Message
switch pack. Warning messages and prompts are displayed in the
MG Pilot information centre in the instrument pack. Any
communications are displayed in 'pop up' messages, these
Displays the active safety information of the vehicle. can be divided into the following categories:
Health Centre • Operating Instruction
• Tyre Pressure: displays the current status of each wheel. • System State Instruction
• Battery Voltage: displays the 12V Battery Voltage. • System Malfunction Alert
• Warning Information ： displays the warning Please follow the instructions displayed in the 'pop up'
information or important notes that are currently message or in the case of a warning message, please refer
relevant to the vehicle. to the relevant section of the owners manual to follow the
correct instructions.
Settings
The following are a selection of warning messages that may
Luminance Level appear in the information centre.
19
Warning Message Procedure Warning Message Procedure
As soon as conditions permit, Indicates that the power system
safely stop the vehicle and has detected a fault. As soon
DANGER! Evacuate evacuate all occupants as conditions permit, safely
Vehicle Control
Vehicle Safely! immediately, and contact an stop the vehicle and switch
System Fault Please
MG Authorised Repairer the vehicle power system to
Stop Safely!
immediately. the OFF position and contact
Vehicle Control Indicates that the power system an MG Authorised Repairer
System Fault Please has detected a fault. Please immediately.
ask Serving Station contact an MG Authorised Indicates that the Manual Speed
for Help! Repairer as soon as possible. Assist (MSA) function has failed.
MSA Fault
Indicates that the power system Please contact an MG Authorised
Vehicle Control has detected a fault. Please drive Repairer as soon as possible.
System Fault Please carefully and contact an MG Indicates that the Intelligent
drive carefully! Authorised Repairer as soon as Speed Assist (ISA) function has
possible. ISA Fault failed. Please contact an MG
Authorised Repairer as soon as
possible.
20
Warning Message Procedure Warning Message Procedure 1
Indicates that the lane departure Indicates that the auto
Lane Departure warning system (LDW) has emergency braking system
Pedestrian Auto
Warning System detected a fault. Please contact for pedestrians (AEBP) has
Emergency Braking
Fault an MG Authorised Repairer as detected a fault. Please contact
Fault
soon as possible. an MG Authorised Repairer as
Indicates that the emergency soon as possible.
Emergency Lane lane keeping system (ELK) has Indicates that the adaptive
Keeping System detected a fault. Please contact cruise control system (ACC) has
Fault an MG Authorised Repairer as ACC System Fault detected a fault. Please contact
soon as possible. an MG Authorised Repairer as
Indicates that the forward soon as possible.
collision warning system (FCW) Indicates that the traffic jam
Forward Collision
has detected a fault. Please assist system (TJA) has detected
System Fault Traffic Jam Assist
contact an MG Authorised a fault. Please contact an MG
System Fault
Repairer as soon as possible. Authorised Repairer as soon as
Indicates that the auto possible.
Auto Emergency emergency braking system (AEB)
Braking System has detected a fault. Please
Fault contact an MG Authorised
Repairer as soon as possible.
21
Indicates that the rear drive Indicates that the anti-lock brake
assist system (RDA) has detected system (ABS) has detected a
Rear Drive Assist
a fault. Please contact an MG fault. and the ABS function is
System Fault ABS Fault
Authorised Repairer as soon as about to be disabled. Please
possible. contact an MG Authorised
Indicates that the passive keyless Repairer immediately.
entry function has detected a Indicates that a fault has been
Passive Entry Fault fault. Please contact an MG detected within the braking
Authorised Repairer as soon as system. Stop the vehicle as
possible. Brake Fault soon as safety permits, switch
Indicates that the power mode the vehicle power system OFF,
Ignition System has detected a fault. Please and contact an MG Authorised
Fault contact an MG Authorised Repairer immediately.
Repairer immediately. Indicates that the SCS system has
Indicates that the START/STOP Stability Control detected a fault. Please contact
Start Stop Button Switch has detected a fault. Fault an MG Authorised Repairer
Fault Please contact an MG Authorised immediately.
Repairer immediately.
22
Indicates that the TCS system Indicates that the HDC system
Traction Control has detected a fault. Please Hill Descent has detected a fault. Please
Fault contact an MG Authorised Control Fault contact an MG Authorised
Repairer immediately. Repairer as soon as possible.
Indicates that the EPB system has Indicates that the electric
Parking System detected a fault. Please contact power steering system (EPS)
Fault an MG Authorised Repairer as has a general failure and the
soon as possible. performance is reduced. As
Indicates that the electronic soon as conditions permit, safely
parking brake system has stop the vehicle and switch the
Park Brake Force vehicle power system to the
detected a fault when parking.
Not Enough OFF position. After a short
Please contact an MG Authorised EPS Performance
Repairer as soon as possible. while, switch the vehicle power
Reduced
system to the READY position,
Indicates that the auto hold drive the vehicle a short distance
function has detected a fault. and monitor the operation of
Autohold Fault
Please contact an MG Authorised the steering. If the message is
Repairer as soon as possible. still displayed or the steering
assistance reduced, please
contact an MG Authorised
23
Indicates that the electric Indicates that the ESCL has
power steering system (EPS) has detected a fault. As soon
EPS Assistance
detected a fault. Please contact as conditions permit, safely
Failure
an MG Authorised Repairer stop the vehicle and switch
ESCL Fault
immediately. the vehicle power system to
Indicates that the steering angle the OFF position and contact
sensor has failed. Please contact an MG Authorised Repairer
Steering Angle Fault immediately.
an MG Authorised Repairer as
soon as possible. Indicates that the SDM has
Indicates that the steering angle detected a fault. As soon
Steering Angle sensor is not calibrated. Please as conditions permit, safely
Uncalibrated contact an MG Authorised stop the vehicle and switch
Airbag Fault
Repairer as soon as possible. the vehicle power system to
the OFF position and contact
an MG Authorised Repairer
immediately.
24
Indicates that the tyre pressure Indicates that the front view
monitoring system (TPMS) has camera module (FVCM) has
Front Camera
TPMS Fault detected a fault. Please contact detected a fault. Please contact
System Fault
an MG Authorised Repairer as an MG Authorised Repairer as
soon as possible. soon as possible.
Indicates that the TPMS has Indicates that the front view
Front Left/Front
detected a sensor has a low camera module (FVCM)
Right/Rear Front Camera
battery. Please contact an MG calibration has failed. Please
Left/Rear Right Tyre Calibration Failed
Authorised Repairer as soon as contact an MG Authorised
Sensor Battery Low
possible. Repairer as soon as possible.
Indicates that the 12V battery Indicates that the radar module
12V Battery charging system has detected RADAR Calibration calibration has failed. Please
Charging System a fault. Please contact an Failed contact an MG Authorised
Fault MG Authorised Repairer Repairer as soon as possible.
immediately.
Indicates that the CCU has
DCDC Charge detected a fault. Please contact
Fault an MG Authorised Repairer
immediately.
25
Indicates that the vacuum system Indicates to the driver via a
has detected a fault. As soon green SOS warning lamp that
as conditions permit, safely an emergency services call is
eCall in process
Vacuum System stop the vehicle and switch currently in progress. The SOS
Fault the vehicle power system to button LED status indicator
the OFF position and contact flashes once per second.
an MG Authorised Repairer Indicates to the driver via a
immediately. yellow SOS warning lamp that
Indicates that the motor has the ecall system has detected a
overheated. Please contact an fault and is not operating within
Motor Overheating
MG Authorised Repairer as soon eCALL system fault its parameters. The SOS button
as possible. LED status indicator flashes
Indicates that the drive motor twice per second. Please contact
has detected a fault. As soon an MG Authorised Repairer as
as conditions permit, safely soon as possible.
stop the vehicle and switch
Motor Fault
the vehicle power system to
the OFF position and contact
immediately.
26
Warning Message Procedure 1
Indicates to the driver via a
red SOS warning lamp that the
ecall system has failed and is
not capable of supporting in the
eCALL system
event of an accident. The SOS
failure
button LED status indicator is
not illuminated. Please contact
immediately.
Indicates to the driver via a red
SOS warning lamp that automatic
ecall service is disabled. Please
Auto eCall Disabled
contact an MG Authorised
Repairer to reactivate the
automatic ecall function.
27
Warning Lights and Indicators
If any warning light or indicator appears in the instrument pack during the process of vehicle starting or driving, it means
that the relevant system is in a certain state or has a fault. Some warning lights will illuminate or flash accompanied with
warning tone or prompt message.
Please read the following instructions in detail for the meaning of the relevant warning lights and indicators. In case of
failure, please take corresponding measures in time and contact an MG Authorised Repairer as soon as possible.
Name Icon Description
Main Beam Indicator The headlamp high beam is turned on.
Auto Main Beam

The auto main beam function is enabled.
Indicator
Side Lamp Indicator The side lamps are on.
Rear Fog Lamp Indicator The rear fog lamps are on.
28
When the turning signal lamp flashes, the direction indicator lamp on the 1
corresponding side also flashes. If the hazard warning lamps are operated,
Direction Indicators both direction indicator lamps will flash together.
If either direction indicator lamp in the instrument pack flashes very rapidly,
it indicates that the turning signal light on the corresponding side has failed.
It indicates that the SRS or the seat belt has failed. As soon as conditions
permit, safely stop the vehicle and switch the vehicle power system to the
Airbag Warning OFF position and contact an MG Authorised Repairer immediately. An SRS
or seat belt fault may mean the components may not be deployed in the
event of an accident.
Seat Belt Unfastened If this lamp illuminates or flashes, it indicates that the seat belt for the driver
Warning or passenger remains unfastened.
If no valid key is detected, this lamp will illuminate. Please use the correct
key, or put the smart key at the alternative starting position. For specific
Immobiliser System location requirements, refer to "Alternative Starting Procedure" in "Starting
Warning & Driving" section.
If the remote key battery is low, this lamp flashes. Please replace the battery
as soon as possible.
29
If this warning lamp illuminates, it indicates that a tyre pressure is low. Please
Tyre Pressure check the tyre pressures.
Monitoring System
(TPMS) Warning If this lamp flashes first and then remains illuminated after a period of time,
it indicates the system has detected a fault.
If this lamp illuminates, it indicates that the electric power steering system
has a general failure and the performance is reduced. Please stop the vehicle
as soon as safety permits. If the lamp still illuminates after restarting the
vehicle and driving for a short while, please contact a local MG Authorised
Repairer for service immediately.
If this lamp flashes, it indicates the electric steering column lock has a
failure. Please stop the vehicle as soon as safety permits, and turn off the
Electric Power Steering START/STOP Switch.
(EPS)/Electronic
Steering Column Lock If this lamp extinguishes after flashing for a while, it indicates that the
(ESCL) Warning steering wheel is locked. Please attempt to release the lock by rocking the
steering wheel left to right.
If this lamp illuminates, it indicates the electric power steering system has a
general failure relevant to steering angle.
If this lamp flashes, it indicates the electric power steering system has a
severe failure and it is hard to steer. Please stop the vehicle as soon as
safety permits.
30
Stability
If this lamp illuminates, it indicates that the stability control system or 1
Control/Traction traction control system has failed.
Control System If this lamp flashes while driving, it indicates that the system is operating to
Warning Lamp
assist the driver.
Stability
Control/Traction
The stability control / traction control system is switched off manually.
Control System OFF OFF
Warning
If this lamp illuminates, it indicates that the HDC system is in the standby
state.
Hill Descent Control
(HDC) On/Malfunction If this lamp flashes, it indicates that the vehicle is under the control of HDC.
Indicator
The HDC system has detected a fault.
Auto Hold Status

Indicator P The auto hold system is operating to assist the driver.
31
If this lamp illuminates, it indicates that the EPB is enabled.
Electronic Parking Brake If this lamp flashes, it indicates that the vehicle is parked on an excessive
(EPB) Status Indicator P slope or the EPB system has failed. Please securely park the vehicle on a
safe road.
Electronic Parking
Brake (EPB) System P The EPB system has detected a fault.
Malfunction Warning
Brake System The brake system has failed. Please stop the vehicle as soon as safety
Malfunction Warning permits, and turn off the START/STOP Switch.
The ABS has failed.

ABS Malfunction ABS
Warning If an ABS failure occurs while driving, ABS operation will be suspended, but
normal braking will still be available.
This indicator is used to inform the driver that the vehicle has a stored
System Fault Message
warning message. Please view the fault message or important notes in the
Indicator
information centre. Refer to "Information Centre" in this chapter.
32
If this lamp illuminates after starting the vehicle, it indicates that the 1
low-voltage battery charging system has failed.
Low-voltage Battery
Charging System If this lamp flashes, it indicates that the battery power is low, and a
Malfunction Warning prompt message appears in the instrument pack. At this time, the system
will restrict or turn off some electrical devices. Please start the vehicle
immediately to charge the battery.
High-voltage Battery If this lamp illuminates or flashes, it indicates that the high voltage battery
Pack Low Battery charge is low. Where possible please charge the high voltage battery before
Warning this lamp enters the flashing stage.
High-voltage Battery
The high voltage battery is disconnected or isolated.
Pack Cutoff Warning
If this lamp illuminates, it indicates that the high voltage battery has detected
High-voltage Battery a fault.
Pack Malfunction If this lamp flashes, it indicates that the high voltage battery temperature is
Warning too high. Please stop the vehicle as soon as safety permits and leave the
vehicle immediately.
Charging Connection
The vehicle is connected to a charge point.
Indicator
33
Charging Status When the vehicle is connected to an external power supply for charging,
Indicator this lamp will illuminate and extinguish after charging is completed.
Driving Power Limited

The vehicle power has been reduced.
Warning
The vehicle has a fault and its performance is limited.

Power System
Malfunction Warning
The vehicle has a serious fault. Please stop the vehicle as soon as safety
permits, and turn off the START/STOP Switch.
READY Indicator The vehicle is ready for driving.
Displays the current driving mode of the vehicle: NORMAL、SPORT、

Driving Mode Indicator NORMAL
ECO.
Braking Energy
Recovery Level 1 Displays the current braking energy recovery level of the vehicle.
Indicator
34
The Manual Speed Assist System is activated.

1
Manual Speed Assist If this lamp illuminates, it indicates that the Manual Speed Assist System is
System Indicator
in the standby state.
If the Manual Speed Assist System has a fault, the lamp will flash yellow and
then extinguish.
The Intelligent Speed Assist System is activated.
Intelligent Speed Assist If this lamp illuminates, it indicates that the Intelligent Speed Assist System
System Indicator
is in the standby state.
If the Intelligent Speed Assist System has a fault, the lamp will flash yellow
and then extinguish.
Manual Speed Assist NNN

This lamp will illuminate when the Manual Speed Assist System is enabled.
System Speed Indicator mph
'NNN' denotes the current setting value of the speed limit.
Speed Limit Sign

N N N 'NNN' denotes the speed value of speed limit sign currently recognised.
Indicator
35
Speed Limit Sign The speed limit sign currently recognised has additional information. Please
Additional Information NNN
Warning pay attention to it.
National Speed Limit When the overspeed alarm or intelligent speed limit function is on, the
Sign Indicator national speed limit sign is recognised.
The Adaptive Cruise Control System is activated.
Adaptive Cruise
Control System The Adaptive Cruise Control System is in the standby state.
Indicator
The Adaptive Cruise Control System has a fault.
36
The Traffic Jam Assist System is activated.

1
Traffic Jam Assist System If this lamp illuminates, it indicates that the Traffic Jam Assist system is in
Indicator
the standby state.
If this lamp remains illuminating after flashing for a while, it indicates that
the system cannot work normally.
The lane departure warning function is on and meets the activation

conditions.
If this lamp illuminates, it indicates that the lane departure warning function
Lane Assist System is in the standby state.
Indicator If this lamp remains illuminating after flashing for a while, it indicates that
The lane keep assist function is on and meets the activation conditions.
37
If this lamp illuminates, it indicates that the lane keep assist function is in the
standby state.
If this lamp remains illuminating after flashing for a while, it indicates that
If this lamp illuminates, it indicates that any function of the Forward Collision
Forward Collision System is off.
System Indicator If this indicator illuminates when all the functions is enabled, it indicates that
the Forward Collision System cannot operate normally.
The Rear Driving Assist System is turned off, the radar is covered or the
Rear Driving Assist
system has failed, the corresponding prompt message will appear in the
System Indicator *
instrument pack.
38
The system is ready and an emergency services call (eCall) is in progress.

1
The system is still capable of sending out a vehicle information message to

eCall SOS Indicator the call centre, but other eCall capabilities are limited due to a fault in the
system.
The eCall system has failed and not operational.
Note: There are some circumstances where a warning light may illuminate or a warning message is displayed
as an indication of an issue with the associated system, this does not necessarily indicate a fault. If in doubt,
please seek advice from an MG Authorised Repairer.
39
Lights and Switches AUTO Lamp
When the vehicle power system is in the ACC position,
Master Lighting Switch
the auto lighting system defaults to the ON position (1).
The auto lighting system will automatically switch the side
3 lamps and switch illumination on and off according to the
2 intensity of current ambient light.
With the vehicle power system switched to the
1 ON/READY position, the auto lighting system defaults
to the ON position (1). The auto lighting system will
4 automatically switch the side lamps, switch illumination
and dipped headlamps on and off according to the intensity
of current ambient light.
Note: This function is realized by fitting a sensor
capable of monitoring exterior lighting conditions
in real time on your vehicle. The sensor is fitted in
the centre of the fascia panel near the windscreen in
1 AUTO Lamp
some models. DO NOT mask or cover this area, or
2 Side Lamps and Switch Illumination the headlamps may automatically come on when not
necessary.
3 Dipped Headlamps
4 Lights OFF
40
Side Lamps and Switch Illumination Lights Off 1
When the START/STOP Switch is in the ACC position, turn Turn the master lighting switch to position 4, this will
the master lighting switch to position 2 to operate the side switch off all lamps, releasing the switch will allow it to
lamps and switch illumination. return to the AUTO switch position.
When the START/STOP Switch is in the ON/READY Daytime Running Lamp
position, turn the master lighting switch to position 2 to
operate the daytime running lamps, rear side lamps and The daytime running lamps turn on automatically when the
switch illumination. START/STOP Switch is in the ON/READY position. When
the dipped headlamps are switched on, the daytime running
With the START/STOP Switch in the OFF position if the lamps extinguish automatically.
lighting switch is in position 2 and the driver’s door is
opened an audible warning will sound to alert the driver, Follow Me Home
the side lamps will remain on.
After the START/STOP Switch is turned off, pull the lighting
Dipped Headlamps stalk switch towards the steering wheel. This will enable
the Follow Me Home function, dipped beam headlamps
When the START/STOP Switch is in the ON/READY and side lamps will illuminate depending upon the vehicle
position, turn the master lighting switch to position 3 configuration. It can be set on the entertainment display.
to operate the dipped headlamps, side lamps and switch
illumination.
41
Headlamp Levelling Manual Adjustment Location Load
0 Driver, or driver & front passenger.
1 All the seats occupied with no load.
All the seats occupied plus an evenly

2 distributed load in the boot, or driver with
full load.
Driver only, plus an evenly distributed load in

3
the boot.
Position 0 is the initial position of the headlamp levelling

adjustment switch. The headlamp levelling adjustment can
be made as per the following table according to the vehicle
load.
42
Main Beam Switch illuminates, push the lever (1) again or pull the lever (2) to 1
switch to headlamp low beams.
Take care not to dazzle oncoming vehicles
when driving using main beam headlamps. High Beam Flash
To briefly flash the high beam on and off, pull the lever
towards the steering wheel (2) and then release.
Headlamp High/Low Beam Switching

With the START/STOP Switch in the ON/READY position
and dipped headlamps are switched on, push the lever (1)
towards the instrument panel to turn on headlamp high
beams. The high beam indicator lamp in instrument pack
43
Auto High Beam undulating road conditions such as bends,
dips or hills.
The auto high beam system serves only as an
• When the car is driving on a winding road
auxiliary function. The driver must check the
or mountainous road.
status of the front lamps, and turn on the
front lamps when necessary. The auto high beam system is designed to detect the light
For example: The main beam may not be intensity information of the vehicle in front using the vehicle
turned off automatically in the following forward camera and switch the main beam on or off when
cases, thus manual switching between the certain conditions are met. When the auto high beam
main beam and dipped beam is required: system is enabled, the auto high beam indicator in the
• The windscreen is dirty, broken or instrument pack illuminates. After the vehicle is started,
obstructed by other objects blocking the the auto high beam system enters the ready state of work.
view of the sensor. It can be set on the entertainment display.
• The lamps of other vehicles are missing, In the case of automatic control, the system will
damaged, blocked or cannot be detected automatically turn on the main beam when the surrounding
due to weather and other reasons. environment is dark and there is no light detected from
• When pedestrians, non-motor vehicles any vehicles ahead, or oncoming vehicles; when the
and other objects with no obvious light or surrounding environment is bright enough or the system
reflected light are encountered. detects the headlamps or tail lamps of the vehicle ahead
• When the headlamps and tail lamps of or oncoming vehicles, the system will automatically turn
other vehicles cannot be detected due off the main beam.
to the sensor view being impaired due
44
To enable the auto high beam system, the following system again. You can only exit two times in one ignition 1
conditions must be met: cycle. If you exit greater than or equal to three times, you
1 The master lighting switch must be in the Auto will not be able to enable this function again in the current
position and the dipped beam lamps switched on via start cycle. The auto high beam system can be reactivated
automatic control. after the next start cycle.
2 The vehicle is running and the speed is above 25mph IMPORTANT
(40km/h).
The auto high beam function uses data from the front
If the following conditions are met, the vehicle will view camera, always keep the windscreen clean and
automatically exit the auto high beam system. free from residue in this area to maintain optimum
• When the auto high beam system is enabled and the performance of this system. Any damage in this area,
dipped beam lights are automatically turned on, the high such as stonechips must be repaired at the earliest
beam switch is operated. convenience.
• When the auto high beam system is enabled and the
main beam lights are automatically turned on, the high
beam switch is operated.
• When the auto high beam system is enabled and the
main beam lights are automatically turned on, the high
beam flash switch is operated.
If the system exits, quickly push the direction
indicator/main beam switch (main beam 'ON') towards
the instrument pack twice to enter the auto high beam
45
Direction Indicator Switch Fog Lamp Switch
Fog lights should only be used when visibility
2 is below 100m - other road users could be
dazzled in clear conditions.
1
1
Move the lever down to indicate a LEFT turn (1). Move the
lever up to indicate a RIGHT turn (2). The corresponding
GREEN indicator lamp in the instrument pack will flash
when the turning signal lamps are working.
Rotating the steering wheel will cancel the indicator
operation (small movements of the steering wheel may Rear Fog Lamp
not operate the self cancelling). To indicate a lane change, With the START/STOP Switch in the ON/READY position
move the lever briefly and release, the indicators will flash and the headlamps on, turn the fog lamp switch to position
three times and then cancel.
46
1, this will turn on the rear fog lamp, release the switch 1
to allow it to return to the last position. The indicator
illuminates in the instrument panel when the rear fog lamp
is on.
Hazard Warning Lamp

Press the hazard warning lamp button to turn on
the hazard warning lamps. The turning signal lamps and
direction indicator lamps will flash together. Press the
button again to switch off the hazard warning lamps. All
turning signal lamps and direction indicator lamps will stop
flashing.
47
Wipers and Washers • Fast wipe (3)
• Single wipe (4)
*
• Automatic wipe interval adjustment / Rain sensor
sensitivity adjustment *(5)
• Programmed wash/wipe (6)
Intermittent Wipe
By pushing the lever up to the Intermittent wipe position
(1), the wipers will operate automatically. Turn the switch
(5) * to adjust the intermittent wipe frequency. This speed
will also change with the vehicle speed. As the vehicle
speed increases, the wiper frequency increases. As the
vehicle speed decreases, the wiper frequency decreases.
Some models are equipped with a rain sensor fitted to the
interior rear view mirror base to detect varying amounts
of water on the outside of the windscreen. With automatic
Windscreen Wiper Operation wipe, the vehicle will adjust the wiping speed according to
the signals provided by rain sensor. Turn the switch (5) *
The wipers and washers will only operate with the vehicle
to adjust the sensitivity of rain sensor. As the sensitivity
power system in the ACC/ON/READY position. Operate
increases, the wiping interval decreases.
the lever to select different wipe speeds:
• Intermittent wipe (1) Note: Immediately operating the wiper one time can
• Slow wipe (2) be achieved by increasing the sensitivity of rain sensor.
48
If the rain sensor detects continuous rainwater, the IMPORTANT 1
wiper will keep working. When no rain is detected, it
• Avoid operating the wipers on a dry windscreen.
is recommended to switch off automatic wipe.
• In freezing or extremely hot weather conditions,
Slow Wipe make sure that the wiper blades are not
frozen/adhered to the windscreen.
By pushing the lever up to the slow wipe position (2), the
• In winter, remove snow or ice from around the arms
wipers will operate slowly. Move the lever to re-select the
and blades, including the wiped area of the screen.
wipe speed.
Fast Wipe Programmed Wash/Wipe

By pushing the lever up to the fast wipe position (3), the Pulling the lever toward the steering wheel (6) will operate
wipers will operate fast. Move the lever to re-select the the windscreen washers. After a short delay, the wipers
wipe speed. will commence operating in conjunction with the washers.
Note: The wipers continue operating for a further
Single Wipe
three wipes after the lever is released. After several
Pressing the lever (4) down and releasing will operate seconds, there will be a further wipe to remove any
a single wipe, if the lever is held down, the wipers will fluid draining down the screen.
operate continuously until the lever is released.
Note: When the car is stationary, if the bonnet
is opened, the front wiper/washer will stop work
immediately.
49
IMPORTANT Rear Window Wiper Operation
If the washers fail to deliver the screen wash solution
(dirt or ice may have blocked the jets), release the
4
lever immediately. This will prevent the wipers
from operating, and the consequent risk of visibility
being impaired by dirt smearing across the unwashed
windscreen.
The rear window wiper and washer will only operate

with the vehicle power system in the ACC/ON/READY
position. Operate the lever to select different wipe speeds:
• Intermittent wipe (1)
• Wash and wipe (2)
• Wash and wipe (3)
• Intermittent wipe frequency adjustment (4)
50
Intermittent Wipe Note: When the tailgate is opened, rear window wiper 1
operations will be disabled.
Turn the rear window wiper switch to intermittent wipe
(1), the rear window wiper will operate, after 3 consecutive Note: When the windscreen wipers are switched on, if
wipes, the wipers will enter into intermittent mode. The the shift control knob is moved to, or in the R position,
time period between the wipes can be increased/decreased the rear window wiper will operate.
via the intermittent wipe frequency adjustment switch (4).
Wash and Wipe

Turn the rear window wiper switch to wash and wipe (2)
position and hold, the rear window wiper and washer will
operate, the rear window wiper wipes quickly. release the
switch allowing it to return to intermittent wipe (1), the
rear window washer will stop operating.
Turn the rear window wiper switch to wash and wipe (3)
and hold, the rear window wiper and washer will operate.
release the switch allowing it to return to OFF position,
the rear window washer will stop operating, and the rear
window wiper wipes for 3 times, after several seconds, the
wiper will wipe once more to remove the washer fluid on
the windscreen.
51
Steering System 1 Fully release the locking lever.
2 Hold the steering wheel in both hands and tilt the
Adjustment of Steering Column
steering column up or down to move the wheel into
DO NOT attempt to adjust the angle of the most comfortable position.
the steering column while the vehicle is in
3 Once a comfortable driving position has been selected,
motion. This is extremely dangerous.
pull the locking lever fully up to lock the steering
column into its new position.
Electric Power Steering

If the electric power steering fails or cannot
operate the steering will appear very heavy,
this will affect driving safety.
The electric power steering system only works when the

vehicle is in READY mode. The system operates via a
motor with assistance levels automatically adjusted based
on vehicle speed, steering wheel torque and steering wheel
angle.
To adjust the angle of the steering column to suit your

driving position:
52
IMPORTANT 1
Holding the steering wheel on full lock for long periods
will result in a reduction in power assistance causing a
heavier feel to the steering for a short period of time.
53
Horn avoid any potential conflict with the operation of the
airbag.
IMPORTANT
To avoid possible SRS issues, please do not press with

excessive force or hit the airbag cover when operating
the horn.
Press the horn button area on the steering wheel (as

indicated by the arrow) to operate the horn.
Note: The vehicle horn switch location and the driver's
airbag are located in close proximity on the steering
wheel. The illustration shows the position of the horn
switches, please ensure that you press in this area to
54
Rearview Mirrors Mirror Glass Heating 1
The door mirrors have integral heating elements which
The vehicle is fitted with rear view mirrors, these consist
disperse ice or mist from the glass. The heating elements
of a door mirror fitted to each door and a centrally
operate while the Heated Rear Window is switched on.
mounted interior mirror. Rear view mirrors reflect
situations directly behind or on both sides of the vehicle Note: The heating elements of rear window and mirror
thus expanding the driver's field of vision. will only work when the power system is in READY
mode.
The rearview mirrors are safety-critical parts. Proper use
and reasonable mirror angle adjustment can improve the
driver's driving safety and comfort.
Exterior Door Mirrors

Note: Objects viewed in exterior door mirrors may
appear further away than they actually are.
The mirrors can be electrically folded back towards the
side windows into a ‘park’ position to enable the car to
negotiate narrow openings and avoid collisions.
In addition to the folding function, the mirror angle of the
exterior door mirrors can be adjusted electronically. Some
vehicles are also equipped with mirror heating function.
55
Electric Door Mirror Glass Adjustment • Upon completion of the adjustment, rotate the knob
back to the central position, this will ensure no
accidental adjustment of the mirror.
Electric Folding of Door Mirror
• The mirror adjustment function will work with the

START/STOP Switch in all modes, including OFF, ACC
and ON/READY.
• Rotate the knob to select left (L) or right (R) rearview
mirror. Rotate the knob to the middle position, and push the
• Move the knob in the desired direction to adjust the knob down. The door mirrors will be folded automatically.
angle of the exterior mirror glass. Pushing the knob downwards again will return the mirrors
to their original position.
56
Operating the key fob lock/unlock buttons will fold/unfold 1
the door mirrors.
Note: Electrical folding door mirrors that have been
moved from their positions by manual or accidental
means must be reset by operating the knob to
complete fold and deployment one time.
IMPORTANT
• Door mirror glass adjustments and door mirror Move the lever at the base of the mirror forward to ‘dip'
folding are operated by electrical motors. Operating the mirror and achieve the anti-dazzle function. Normal
them directly by hand may damage the internal visibility is restored by pulling the lever back again.
components. Note: In some circumstances, the view reflected in a
• Washing or flushing door mirrors with high pressure ‘dipped’ manual mirror can confuse the driver as to the
water jets or car washes may result in electrical precise location of following vehicles.
motor failure.
Manual Anti-dazzle Interior Rearview Mirror

Adjust the body of the interior rearview mirror to achieve
the best possible view. The anti-dazzle function of the
interior rearview mirror helps to reduce glare from the
headlamps of following vehicles at night.
57
Sunvisor Note: Warnings and instructions on use of child
restraint (3) are attached to both sides of the
The vanity mirror on the driver side should
passenger sunvisor.
only be used when the car is stationary.
NEVER use a rearward facing child restraints on a seat
protected by an ACTIVE AIRBAG in front of it, DEATH
Sunvisors (1) are arranged on the roof ahead of both the
or SERIOUS INJURY to the CHILD can occur. Refer
driver and the front passenger. Some models have vanity
to ‘Disabling the Passenger Airbag'.
mirror (2) , depending on the vehicle configuration. For
the models which have vanity mirror, pull the sunvisor
downward and slide the cover aside to use the vanity
mirror.
L R
AIRBAG
1 2
58
Windows Window Operation 1
Ensure children are kept clear when raising or
lowering a window.
Improper use or activation of the electric

1
windows by children could cause serious harm
2 or even death. It is the responsibility of the
3 driver and adult passengers to ensure that
4 when carrying children the necessary steps
5 are taken to isolate the window operation.
This should include the removal of the key
when children are left alone in the vehicle.
1 Front Right Window Switch Push the switch (1-4) down to lower, and pull the switch up
2 Front Left Window Switch to raise the window. The window will stop moving as soon
as the switch is released (unless the ‘One-Touch’ function
3 Rear Right Window Switch is active).
4 Rear Left Window Switch Note: The front and rear passenger windows can also
5 Rear Window Isolation Switch be operated by individual window switches, mounted
on each door. The rear window switches will not
operate if the rear window isolation switch has been
activated.
59
Note: The electric windows can be operated with the position for a short time and releasing will automatically
vehicle power system in the ACC, ON and READY close the window completely. Window movement can
positions. (For safety: doors should be closed). be stopped at a desired position at any time by briefly
operating the switch again.
Rear Window Isolation Switch
The “Anti-Trap” function is a safety feature which prevents
Press the button (5) to isolate the rear window controls, the window from fully closing if an obstruction is sensed -
press again to restore control. if this happens the window will open slightly to allow the
Note: It is recommended that you ISOLATE the rear obstruction to be removed.
window switches when carrying a child. Note: DO NOT operate the power window controls
continuously several times in a short time frame,
“One-Touch” Down otherwise the power window controls may be disabled
The driver's window control switch (1) has 2 positions. to protect the motor. If this occurs, please wait a few
Short press the window control switch to the "2" position seconds until the motor cools down. In the case of
and release. The window automatically descends to fully the driver’s window with "One Touch and Anti-Trap"
open. Window movement can be stopped at desired please wait 30 seconds prior to operation. In some
position at any time by operating the corresponding switch cases it may take 30 minutes to completely cool down,
during descent. during which time the negative battery lead should
not be disconnected.
“One Touch” Up with “Anti-Trap”
Note: If the battery is disconnected, the “One-Touch”
The driver's window control switch (1) has the and “Anti-Trap” features will be lost. To restore this
“one-touch” up function. Lifting the switch to the "2" feature, fully close the window and hold the switch for
60
5 seconds, and then fully open the window and press 1
the switch for 5 seconds.
61
*
Sunroof • DO NOT use abrasive materials to clean the sunroof
glass. Use alcohol based solvent.
The sunroof consists two pieces of glass and one sunshade. • DO NOT hold the operating switch in the open/close
The front glass can be opened by sliding or tilting, the rear position for any length of time after operation is
one is fixed and cannot be opened, and the sunshade can complete, this could damage the electrical components.
slide open. • Clean the sunroof regularly to maintain operation and
performance. Visit an MG Authorised Repairer for
Instructions service as required.
DO NOT allow passengers to lean out of an
open sunroof whilst the vehicle is in motion.
Injuries may occur from objects such as tree
branches.
Safety of the vehicle occupants must be

observed at all times. DO NOT allow limbs to
be placed in the moving path of the sunroof
at any time, injury may occur.
• Avoid fully opening the sunroof during rain showers.

• It is advised not to open the sunroof at high speeds.
• Where possible, please clean any residual water or
raindrops off the sunroof prior to opening. Failure to
do so may result in water entering the car.
62
Sunroof Operation 1
2
1
3
1 4
2
Push the sunroof glass switch upward to the 1st position
(1) and hold, the sunroof will tilt open manually. You can
stop the movement of the sunroof at any time by releasing
the switch.
When the START/STOP Switch is set to ACC or Push the glass switch with slightly harder force to move the
ON/READY, you can operate the sunroof. switch to its 2nd position (2) and then release, the sunroof
will automatically open completely.
Switch 1 is used to operate the sunroof sunshade, and
switch 2 is used to operate the sunroof glass. The Close the Sunroof Glass by Tilting
operational function is identified by the icons on the
Pull the sunroof glass switch downward to the 1st position
switches.
(3) and hold, the sunroof will close manually. You can stop
Sunroof Glass Operation the movement of the sunroof at any time by releasing the
switch.
Open the Sunroof Glass by Tilting
63
Pull the glass switch with slightly harder force to move the Close the Sunroof Glass by Sliding
switch to its 2nd position (4) and then release, the sunroof
Push the sunroof glass switch forward to the 1st position
will automatically close completely.
(1) and hold, the sunroof will close manually. You can stop
Open the Sunroof Glass by Sliding the movement of the sunroof at any time by releasing the
switch.
Push the glass switch forward with slightly harder force to
4 move the switch to its 2nd position (2) and then release,
3 the sunroof will automatically fully close. You can stop the
movement of the sunroof at any time by pushing the switch
forward again.
1 Note: Due to the design of the sunroof there may
2 be occasions where using the manual close function
provides a visual impression that the glass is fully
Push the sunroof glass switch backward to the 1st position closed, this may not be the case, it is recommended
(3) and hold, the sunroof will slide open manually. You can to use the 2nd position to automatically close the
stop the movement of the sunroof at any time by releasing sunroof glass when it needs to be completely closed
the switch.
Push the glass switch backward with slightly harder force
to move the switch to its 2nd position (4) and then release,
the sunroof will automatically open fully. You can stop the
movement of the sunroof at any time by pushing the switch
backward again.
64
Sunroof Sunshade Operation Push the sunroof sunshade switch forward to the 1st 1
position (1) and hold, the sunshade will close manually.
You can stop the movement of the sunshade at any time
4 by releasing the switch.
3 Push the sunshade switch forward with slightly harder force
to move the switch to its 2nd position (2) and then release,
the sunshade will automatically fully close. You can stop
1 the movement of the sunshade at any time by pushing the
2 switch forward again.
Open the Sunshade Note: If the vehicle is to be parked in direct sunlight for
a length of time it is recommended that the sunshade
Push the sunroof sunshade switch backward to the 1st be closed to protect the interior trim components from
position (3) and hold, the sunshade will slide open manually. damage, and to help regulate the in car temperatures.
You can stop the movement of the sunshade at any time by
releasing the switch. Anti-pinch Function
Push the sunshade switch backward with slightly harder The sunroof and sunshade feature an “Anti-Pinch”
force to move the switch to its 2nd position (4) and then function, this is a safety feature which prevents the
release, the sunshade will automatically open fully. You can sunroof or sunshade from fully closing whilst in the
stop the movement of the sunshade at any time by pushing automatic mode if an obstruction is sensed - if this
the switch backward again. happens the sunroof/sunshade will open slightly to allow
the obstruction to be removed.
Close the Sunshade
65
Note: For some vehicles, if the anti-pinch is triggered switch forwards to the 1st position and hold it until the
three times in succession, the sunroof/sunshade sunshade closes fully.
cannot be operated in automatic mode. You can
Note: The anti pinch function is suspended during this
only move the sunroof/sunshade switch to the 1st
operation.
position and hold it to operate in manual mode. The
automatic operation function will be restored after Linkage between Sunshade and Sunroof Glass
the sunroof/sunshade is completely closed once.
To prevent the sunshade from being exposed, the sunshade
Forcibly Closing the Sunroof (over-riding the anti will move together with the sunroof glass as one unit when
the sunroof is opened. To close the sunshade, the sunroof
pinch)
glass will close first.
To forcibly close the sunroof glass after an anti-pinch
intervention, gently slide the glass switch forwards to the Sunroof Initialisation
1st position and hold in position until the sunroof glass is In the event of a power failure or battery disconnection
fully closed. when the sunroof glass or sunshade is in motion, the
Note: The anti pinch function is suspended during this sunroof/sunshade will require initialisation when the power
operation. is restored.
To carry out the sunroof glass initialisation operation:
Forcibly Closing the Sunshade (over-riding the anti
Fully close the glass - gently slide the switch forward to
pinch) the 2nd position and hold in position for 10 seconds. The
To forcibly close the sunshade that has reopened due to sunroof will open a preset amount and stop, it will then
activation of anti-pinch function: gently slide the sunshade close automatically - the sunroof glass is then initiailised.
66
During the whole process, the switch must remain in the 1
2nd position.
To carry out the sunshade initialisation operation:
Fully close the sunshade - slide the close switch forward
to the 2nd position and hold in position for 10 seconds.
The sunshade will open a preset amount and stop, it will
then close automatically - the sunshade is then initiailised.
During the whole process, the switch must remain in the
2nd position.
Thermal Protection
To prevent the sunroof glass motor and the sunshade
motor from being overheated and damaged, the motors
are designed with a thermal protection function.
After the thermal protection function is activated, the
sunroof/sunshade does not respond to other operations
except the closing operation. After the motor has cooled
down and exits the thermal protection state, the sunroof
can be operated normally until the next thermal protection
event.
67
Interior Light Press switch 1 to turn on the front and rear interior lamps,
press again to turn off.
According to different configurations of the vehicles, the
Press either of the buttons 2 to turn on a corresponding
front interior lamp may feature bulb or LED configurations.
front interior lamp, press again to turn off.
In addition to the manual control of the interior lamps,
1 some operating conditions will activate an automatic
2
control function. Press button 3 to turn on or turn off the
3
2 automatic control.
2 3 2
Interior light illumination occurs automatically whenever
the following occur.
LED • The car is unlocked.
• Any door is opened.
Bulb • The vehicle power system is switched off, providing the
vehicle light sensor detects that the ambient light level
1 Main Manual Control Switch of Front/Rear Interior is low or the sidelights have been illuminated during the
Lamps previous 30 seconds.
2 Manual Control Button of Corresponding Front Note: If a door is open for more than a certain period
Interior Lamp of time, the front interior lamp will be switched off
automatically to avoid battery drain.
3 Automatic Control Button
68
Power Socket 1
Front Power Socket
Please ensure the socket blanking plug is
inserted when the power socket is not in use. 12V
This will ensure no debris or foreign objects

enter the socket preventing its use or cause
short circuits. 1
The 12V power socket has a voltage rating of 12V
12V, and the maximum power of 120 Watt,

please DO NOT use any electrical appliance 2
that exceeds this rating.
The 12V power socket is located in front of the shift
Extended use of the accessory power socket
control knob assembly in the centre console. It can be
and USB socket when the vehicle power
used as a power supply when the START/STOP Switch is
system is switched off will cause premature
in the ACC or ON/READY positions when the blanking
discharging of the vehicle battery.
plug is removed.
Located to the right of the power socket are two USB
ports. Both of them can be used to provide a 5V power
supply or a data transmission connection.
69
Note: Due to differences in configuration the charging There are two USB ports located at the rear of the centre
function of the USB port will be slower. console, these provide a 5V power source as a power
outlet.
Note: The vehicle is not supplied with a cigar lighter.
If required please contact your local MG Authorised Note: Due to differences in configuration the charging
Repairer. function of the USB port will be slower.
Rear USB Ports Top USB Port
70
There is also one USB port located in the rear view mirror 1
mounting trim cover, this provides a 5V power source.
Note: Due to differences in configuration the charging
function of the USB port will be slower.
71
Wireless Charging System for Mobile Wireless Charging of Mobile Phones
Phones *
The wireless charging function for a mobile phone is

realized without the necessity for a connection cable. It is
achieved using electromagnetic induction.
Note: The wireless charging function does not apply
to all mobile phones, only brands/models with wireless
charging function.
The wireless charging area is located in the area shown

in the figure. The charging function is enabled when the
START/STOP Switch is placed in the ACC/ON/READY
positions. Place the phone face up horizontally in the
charging area, which can be used for wireless charging.
Note: Only one mobile phone can be charged at a
time.
72
Note: On bumpy roads, the wireless charging function IMPORTANT 1
of the mobile phone may intermittently stop and
When the wireless charging system of the mobile phone
resume. If the mobile phone deviates from the
is being used, make sure that the smart key is 20cm or
charging area and stops charging, it will need to be
more away from the wireless charging area.
placed back in the rechargeable area.
Do not place coins, IC cards, metal keys, or other
Note: The size of each brand of mobile phone is items with a large amount of metal composition in the
different, and the position of the charging coil on the wireless charging area with your phone. This may result
mobile phone is different. Please adjust the position in the failure of wireless charging function and create a
of the mobile phone accordingly. In addition, the safety hazard.
case of some mobile phones may have an impact on
wireless charging. It may be necessary to adjust or
remove the case to achieve wireless charging.
If the mobile phone cannot be charged correctly, please
make sure that there is no foreign matter in the wireless
charging area or wait for the wireless charging area to cool
down before further attempts. If it still fails, seek an MG
Authorised Repairer.
73
Storage Devices Glove Box
Instructions
• Please close all storage devices when the vehicle is in
motion. Leaving these storage devices open may cause
personal injury in cases of a sudden start-off, emergency
braking or a car accident.
• Do not place flammable materials such as liquid or
lighters in any storage devices. The heat in hot
conditions may ignite flammable materials and result in
a fire.
To open the glove box, pull the handle on the glove box
cover (as indicated by the arrow).
Push the box cover forward to close the glove box. Make
sure the glove box is fully closed when the vehicle is in
motion.
74
Centre Console Armrest Box Loadspace 1
DO NOT place articles on the rear parcel
shelf, they could move causing personal
injury in the event of an accident ，
emergency braking or hard acceleration.
Lift the armrest (arrowed) to open the compartment cover.

Put the cover down to close it. 2
The rear parcel shelf is connected to the tailgate using

straps and hooks. When opening the tailgate, the shelf will
automatically be raised.
75
The spare wheel/tyre repair kit and tool kit are stowed
beneath the loadspace carpet, lift the carpet for access.
Always refit the carpet after use.
In addition, The loadspace carpet height can be adjusted by
using the carpet bracket (figure 1, 2).
76
Cup Holder 1
Do not place hot drinks in the cup holder
whilst driving. Spillage may result in personal
injury or damage.
Centre Console Cup Holder
The centre console cup holder is situated at the front end

of the centre console armrest assembly.
77
*
Roof Luggage Rack • The overall height of the car is different when loads are
fitted to the roof luggage rack. Please ensure there is
Roof loads MUST NOT exceed the maximum
adequate clearance when entering tunnels and garages.
authorised load. This may lead to injury or
vehicle damage. • Ensure the loads carried by the roof luggage rack do
not impede operation of the sunroof, roof antenna of
Loose or improperly fixed loads may fall from tailgate opening.
the roof luggage rack and lead to an accident • When installing or removing a piece of loading
or cause injury. equipment, follow the instructions provided by the
manufacturer of the loading equipment.
When heavy or large items are carried Maximum Authorised Load for the Roof
on the roof luggage rack it may lead The maximum authorised load for the roof is 75 kg, and
to changes in steering, handling and the roof load includes the weight of the roof loads and that
braking characteristics. Please avoid sharp of the loading equipment installed.
maneuvers, heavy braking and excessive
Ensure you are aware of the weight of loads, and weigh
acceleration.
them when necessary. Never exceed the maximum
Pay attention to the following when using the roof luggage authorised load for the roof.
rack:
Periodical Check
• Fix loads towards the front of the roof as far as possible,
and distribute the roof load evenly. Alway check the condition and security of bolt connectors
• DO NOT use automatic car washes with loads on the and fasteners before using the rack luggage rack.
roof luggage rack. Periodically check the condition and security of bolt
connectors and fasteners.
78
Air Conditioning and Audio
Systems
2
80 Ventilation
83 A/C Control Panel
85 A/C Control Interface
90 Infotainment System *
AIR CONDITIONING AND AUDIO SYSTEMS
Ventilation
2 2 1 Side Vents
5 5 2 Windscreen/Defrost Vents
3 Centre Vent
4 Front Footwell Vents
5 Front Side Window Vents
6 Centre Console Vents
3 3
1 1
4 4
6 6
80
The air conditioning system is used to adjust the Vents
temperature, speed, humidity and cleanliness of the air in
the car. Fresh air is drawn in through the air intake grille
Centre Vents
at the base of the front windscreen and A/C filter. 2
Always keep the air intake grille clear of obstructions such
as leaves, snow or ice.
A/C Filter
The A/C filter is used to filter air. To remain fully effective,
the filter should be replaced at the recommended service
interval.
Slide the button in the centre of the louvres to the left or

right to open or close the vent.
Toggle the button at the centre of each vent up and down,
left and right to regulate the air direction.
81
Side Vents Centre Console Vents
Rotate the centre thumb-wheel clockwise or Slide the button in the centre of the louvres to the left or
anti-clockwise to open or close the vent. right to open or close the vent.
Toggle the centre thumb-wheel up, down, left or right to Toggle the button at the centre of each vent up and down,
adjust the air direction. left and right to regulate the air direction.
82
A/C Control Panel A/C Control Shortcut
ON/
Control Panel OFF
Short press the A/C control shortcut to display
the air conditioning interface on the infotainment screen. 2
Long press the A/C control shortcut to switch the system
on, all functions will revert to the state before shutdown.
Long press again to switch off.
Defrost/Demist
1 2 3 4 5 Press Defrost/Demist Button on the control

panel, the indicators on the button and display illuminate,
the A/C cooling and external circulation functions are
switched on, and the system enters the defrost/demist
function to clear the windshield and side windows.
1 A/C Control Shortcut Press again to switch off. The indicator will go off and the
2 Defrost/Demist Button system will return to the previous state
3 Heated Rear Window Button Whilst the defrost/demist is selected, operate the A/C
on/off button to turn the compressor on/off; operate
4 Blower Speed Control Button the air recirculation button to switch between internal
5 Temperature Control Button recirculation and external circulation; operation of either
83
of these functions will not affect the defrost/demist Temperature Control Button
function; operation of any other air distribution modes
will quit defrost/demist.
Press the temperature control button upward
Heated Rear Window or downward to regulate the temperature of the air
supplied by the vents.
The heating elements on the inside of the rear
window are easily damaged. DO NOT scrape
or scratch the inside of the glass. DO NOT
stick labels over the heating elements.
Press the Heated Rear Window Button to

switch the function on or off. The button indicator
illuminates when the function is on, and is extinguished
when the function is off. The heated rear window features
a timer function and will automatically switch off after a
preset time. To continue to use the heated rear window,
operate the button again.
Blower Speed Control Button
Press the blower speed control button upward

or downward to regulate the blower speed.
84
A/C Control Interface
Control Interface - Connected Car *
2
1 Air Distribution Mode Control
1 2 System On/Off
28 c
Outs ide Te mpe ra ture
2 3 Cooling On/Off
PM2.5 F ilter
A/C
3 4 Auto Mode
5 A/C Setting
AUTO
4
6 Air Circulation Mode
5 7 Blower Speed Control
8 Temperature Control
360
360 o
24 c 4
8 7 6
85
Control Interface - Non Connected Car *
1 Air Distribution Mode Control

1 2 System On/Off
28 c
Outs ide Te mpe ra ture
2 3 Cooling On/Off
PM2 .5 Filte r
A/C
3 4 Auto Mode
5 A/C Setting
AUTO
4
6 Air Circulation Mode
5 7 Blower Speed Control
6 8 Temperature Control
AUTO 24 c
7 8
86
Temperature Control Note: To ensure the auto mode operates efficiently,
all windows and the sunroof must be closed and the air
Touch the temperature control touch button to regulate
inlet grille must be clear of obstructions. In addition,
the temperature of the air supplied by the vents.
the A/C Auto control sensor should not be covered. 2
Cooling On/Off
System On/Off
Touch the cooling On/Off touch button to operate the
cooling function. Touch the system On/Off touch button to switch the
system on or off.
Note: A small amount of water may remain in the air
conditioner after usage, this may produce a peculiar Blower Speed Control
smell. If this is a particular issue, it is recommended to
switch off the cooling function and run the blower for Touch the blower speed control touch button to regulate
a while. the blower speed.
Auto Mode Air Distribution Mode

Set the target temperature required and then press the Select the corresponding Air Distribution Mode Touch
AUTO touch button to enable the auto mode function. In Button as required to regulate the air distribution mode.
auto mode, the air distribution mode, blower speed and Touch Button On Air Distribution Mode
other functions are automatically adjusted to reach and
maintain the required temperature. To ‘Face’
Manually adjust the air distribution mode or blower speed
To ‘Face + Feet’
to exit auto mode. In this case the AUTO indicator will
extinguish.
87
Touch Button On Air Distribution Mode Note: In this mode, a small amount of airflow will be
directed to the side vents.
To ‘Feet’
To ‘windscreen’. Directs air to the windscreen/defrost and
To ‘Feet + Windscreen’ front side window vents.
Note: In this mode, a small amount of airflow will be
To ‘windscreen’ directed to the side vents.
Air Circulation Mode

Note: The air distribution mode can also be switched
Touch the air recirculation mode touch button to switch
by touching the air outlet area of the control interface.
between air recirculation modes.
To ‘Face’. Directs airflow to the side and centre vents.
To ‘Face + Feet’. Directs air to footwell, side and centre
vents. During internal recirculation, the air
conditioning system circulates the air inside the car to
To ‘Feet’. Directs air to footwell vents.
meet the requirements of rapid cooling or heating, and at
Note: In this mode, a small amount of airflow will the same time, it can prevent the entry of traffic fumes.
be directed to the side, front side window and front
windscreen vents.
To ‘Feet + Windscreen’. Directs air to the footwell, front During the external circulation, the air
windscreen and front side window vents. conditioning system draws air from outside the vehicle to
ensure fresh air enters the vehicle.
88
During automatic circulation, the air

conditioning system can automatically adjust the internal
recirculation or external circulation according to the 2
situation.
Note: Leaving the system in internal recirculation
mode can cause the windscreen to mist. If this
happens, turn on the defrost/demist mode.
89
*
Infotainment System Using this entertainment system in this condition may
result in permanent damage to the system.
Important Safety Information • Operation of the navigation or video functions of the
• Do not attempt to fit, repair or modify the system is prohibited whilst the vehicle is in motion. MG
entertainment system by yourself, there are Motor accepts no responsibility for any consequences
high-voltage components in the device , which caused by this operation. Please park your vehicle in
may cause electric shock. For internal inspection, a safe location select Park and apply the parking brake
adjustment or repair, please consult a local MG before making the necessary adjustments or watching
Authorised Repairer. Video.
• Do not allow this entertainment and navigation • Particularly high or particularly low temperatures will
system to come into contact with liquids. If liquids interfere with normal operation. If the vehicle has not
or foreign objects enter into this entertainment and been used, is parked in direct sunlight or in particularly
navigation system, please park your vehicle in a safe cold conditions, the car may become particularly hot
place, immediately switch off the power and contact or cold, in this environment the system may not work
a local MG Authorised Repairer. Do not use the properly. Once the temperature inside the car is back
entertainment and navigation system in this condition to normal, the system will resume normal function. If it
because doing so may result in a fire, electric shock, or does not resume, please contact a local MG Authorised
other failure. Repairer for assistance.
• If you notice smoke, abnormal noises or odours from • Excessive use of the entertainment and navigation
the entertainment system, or any other abnormal signs system without the vehicle being driven or in READY
on the screen, switch the power off immediately and mode can drain the vehicle low voltage battery.
contact a local MG Authorised Repairer for service.
90
• Your navigation is only a guide, you must always consider Cautions for Using Screen
and follow the traffic signs, and drive according to road • To protect the screen against damage, be sure to touch
conditions; if you deviate from the recommended route, the panel buttons with your finger (a touch pen can be
the entertainment and navigation system will change the used for special calibration). 2
directive accordingly. • Please protect the screen against direct sunlight.
• When using a mobile phone, keep the antenna of the Extended exposure to direct sunlight will result in
mobile phone away from the screen to prevent the screen malfunction due to high temperature.
disruption of video signal in the form of spots, colored • When the temperature is above or below the operating
stripes, etc. on the screen. temperature range (-30℃ to +85℃), please do not use
the LCD screen, the screen may not operate normally
Privacy and Data Sharing and could be damaged.
When using this entertainment system for the first time, • Do not use excessive force to drag and drop or press
you must read the Privacy Policy carefully and make a the screen, damage or scratching may occur.
choice. • To remove dust from the screen or clean the screen,
please turn the system off first, and then wipe with a
In the settings interface of the entertainment system, you
dry soft cloth. When wiping the screen, take care not
can authorise / disable the data sharing service at any time.
to scratch the surface. Do not use irritative or abrasive
Please note that once disabled, the relevant functions will
chemical cleaners.
not be available.
Note: Restoring factory settings or upgrading software
may require you to reauthorise data sharing services.
91
Basic Operations Main System Interface
Control Panel Page One
1 2 3 4 5 6
1 2
1 (HOME) Button
Short press to return to the main interface；continue
to press for about 10 seconds to restart the system.
2 Volume Adjustment Button
8 7
1 Apple CarPlay
Touch to enter the Apple CarPlay interface.
2 Energy Management
92
Touch to enter the Energy Management interface. • Touch to enter the Music interface.
3 Android Auto • Touch to enter the Vehicle Setting interface.
• Touch to enter the 360 interface.
Touch to enter the Android Auto interface.
Page Two 2
4 Radio/Music
1 2 3 4 5 6
Touch to enter the Radio/Music interface.
5 Navigation Tra ck1 PAS S ENGER
AIRBAG 07:28
Touch to enter the Navigation interface. Refer to

Navigation Manual for details.
We a the r AC Radio User Phone Ve hicle
6 Status Bar
360 o
Displays signal strength, time and other information.
Pull down to enter the shortcut control page, here MG
360 Vide o Setting Rescue Call Touchpoint
you can set the screen brightness, car control, etc.
7 A/C Adjustment 360 o
24 c 4
Touch to adjust temperature, blower speed and air

recirculation mode.
7 8 9 10 11
8 Shortcut Icons
1 Weather
• Touch to enter the main system interface.
• Touch to enter the Navigation interface.
93
Touch to enter the Weather interface. Refer to 8 Video
Touch to enter the Video interface.
2 A/C
9 Setting
Touch to enter the A/C interface. Refer to “A/C
Touch to enter the Setting interface.
Control Interface” in this section for details.
10 Rescue Call
3 Radio
Touch to enter the Rescue Call interface. Refer to
Touch to enter the Radio interface.
4 User
11 MG Touchpoint
Touch to enter the User interface. Refer to Navigation
Touch to enter the MG Touchpoint interface.
Manual for details.
5 Phone
Touch to enter the Bluetooth Phone interface.
6 Vehicle
Touch to enter the Vehicle Settings interface.
7 360
Touch to enter the 360 around view interface. Refer
to “360 Around View System” section in this manual
for details.
94
Power On/Off Steering Wheel Multi-Function Switch Controls
Power On
1 2 3 4
Pressing the START/STOP Switch to select the ACC or
ON/READY position will automatically set the system to
2
power on.
When the system is turned on, press and hold the power
button on the system control panel for about 10 seconds,
the system will restart automatically.
5 67 8 9
Power Off
When setting the START/STOP switch to off, the system
will continue to work for about 10 minutes, and then
automatically power off. 1 Button
After the vehicle is locked, the system will power off Switch to previous track/station.
automatically. Refer to in radio, music and video interface for
details.
2 Button
Mute/Unmute.
3 Volume Up Button
95
4 Button interconnection speech recognition function; short
press again to exit the speech recognition function.
Switch to next track/station.
Refer to navigation manual about the local speech
Refer to in radio, music and video interface for
recognition function for details.
details.
5 Button
Long press to hang up if in calling/talking state; short
press to answer and long press to reject if in incoming
call state.
6 Volume Down Button
7 SRC Audio Source Switch Button
Switch to the next available media audio source.
8 “*” Shortcut Button
The user-defined function of the button can be set in
the vehicle settings.
9 Speech Recognition Function Button
Short press to turn on the local speech recognition
function; long press to turn on the mobile phone
96
Volume Adjustment Bluetooth Phone
The audio volume can be adjusted using the control panel Instructions
, the buttons on the steering wheel and the shortcut • Connection to all mobile phones featuring Bluetooth
control page. During volume adjustment, the system wireless technology is not guaranteed.
2
automatically pops up a volume indication window which
• The mobile phone used must be compatible with
changes smoothly with the adjustment process.
the Infotainment system so that all functions of the
Note: The playback volume of Bluetooth music can connected Bluetooth device can function correctly.
be adjusted by the device itself and the Infotainment • When using Bluetooth wireless technology, the
player. entertainment system may not operate all functions on
the mobile phone.
• When transmitting voice and data via Bluetooth
technology, the straight-line distance between the
entertainment system and the mobile phone should not
exceed 10 metres. However, the actual transmission
distance may be shorter than the estimated distance,
depending on the usage environment.
• When the entertainment system is turned off, the
Bluetooth connection will be disconnected.
• Due to Bluetooth wireless connection, interruption or
error occurring in the process of transmission in some
extreme cases, the entertainment system may be unable
to be paired and connected with the mobile phone.
97
At this time, it is recommended to clear the paired • Call the number in contacts.
devices in the device list on the mobile phone and the • Keypad Input.
entertainment system, and conduct pairing again. • Directly on the mobile phone.
Please connect a bluetooth device first before attempting
Ending a Call
to use any Bluetooth phone functions, Refer to "Bluetooth
Pairing and Connection" in "Settings" section for details. Calls can be ended using the following methods:
Touch the [Phone] card in the main interface to enter the • Touch to hang up.
Bluetooth phone interface. • Long press on the steering wheel to hang up.
· | n 1 14;31
PAS S ENGER
AIRBAG 07:28 P M • Hang up on the mobile phone.
Ala n luckridge
175 2178 59769
Incoming Call
Ca ll
Ala n Buckridge
his tory
Answer an Incoming Call
178 2178 5969
• Touch to answer an incoming call.
Alphons o J e nkins Conta cts • Short press button on the steering wheel to answer
137 3864 8367
an incoming call.
Buddy Kuva lis
Ke ypa d
• Answer an incoming call on the mobile phone.
176 2102 2023
Reject an Incoming Call

360 o
24 c 4
• Touch to reject an incoming call.
• Long press button on the steering wheel to reject an
Making a Call
incoming call.
Calls can be made using the following methods: • Reject an incoming call on the mobile phone.
• Call the number in call history.
98
During a call suitable location and operate the mobile phone where
it is safe and legal to do so.
During a call,
• Touch to enter the Private Mode; Touch to restore
the Speaker Mode. 2
• Touch to switch between Microphone Mute or
Enabled function.
• Touch to enter the keypad interface.
• Touch to add third party calls and keep the current
call. When there are two calls, short press button on
the steering wheel or touch the corresponding contact
icon to switch the call object (It can only be used when
the mobile phone supports three-party call function).
• Touch to check the contacts.
In Private Mode, you may continue with the call using
the mobile phone; the speakers and microphone of the
entertainment system will be muted. Bluetooth remains
connected.
Note: It is illegal to operate a mobile telephone whilst
driving. If you wish to make, or take a call using your
mobile phone directly, please ensure you pull over in a
99
Entertainment Connecting/Disconnecting a USB Storage
Precautions for Playing from a Storage Medium Device
Mode Inserting a USB Storage Device
• The system supports USB drives and Bluetooth storage Connect a USB device to the USB port for connection.
media.
• If the USB device media is not in use, DO NOT leave Removing a USB Storage Device
the device connected. This may result in connection Check and confirm that there is no data being accessed,
deterioration. then pull out the USB storage device.
• Do not remove USB device whilst media is playing.
Note: If any data loss or breach occurs whilst the USB
Failure to follow these instructions could result in
storage device is inserted or being used, it will generally
corrupted data.
be unrecoverable. MG Motor accepts no responsibility
• Keep the USB port dry and free from debris. The port for any data loss or breach.
will become unusable if it is blocked.
• Due to differences in the compression ratio and bit Note: Some USB storage devices may be
rate of the multimedia formats downloaded from the unidentifiable.
Internet and other factors, the actual situation of the
Note: The Infotainment system may not achieve its
decoding result shall prevail.
optimum performance when using some USB storage
devices.
Note: Using a USB hub or extension cable may result

in the USB device not being recognised.
100
Radio 1 Station list of the current transmitter area
Touch [Radio] in the main interface to enter the radio 2 List of valid stations
interface.
3 List of favorite stations
To listen to broadcasts on different bands, touch [DAB],
2
4 Short press to switch to the previous valid radio
[FM] or [AM] on the right of the screen to switch between
station; Long press to switch channels.
radio bands and DAB. Pressing the SRC button can also
switch between the different radio bands. 5 Pause/play the current station
6 Short press to switch to the next valid radio station;
DAB
Long press to switch channels.
7 Add a Station to/Remove a Station from Favorites
1 2 3 4 5 6 7
101
FM/AM 5 Short press to switch to the next valid radio station;
long press to quickly adjust the frequency/amplitude
modulation.
6 Add a Station to/Remove a Station from Favorites
Drag to finely adjust the frequency/amplitude
modulation.
1 2 3 4 5 6
1 List of valid stations
2 List of favorite stations
3 Short press to switch to the previous valid
radio station; long press to quickly adjust the
frequency/amplitude modulation.
4 Pause/play the current station
102
PAS S ENGER
Tra ck2 AIRBAG 07:28
Music
1 Tra ck 1
Tra ck 2
Touch the Radio/Music area in the main interface or the Artis t 2 BT
mus ic
Tra ck 2 Artis t 2’s s ong
icon to enter the music interface.
Touch [BT music] / [amazon music] / [USB music] on 3 Tra ck 3
Sound aduj s tme nt
a ma zon
2
mus ic
the right of the screen to enter the corresponding music 4 Tra ck 4

01:43 02:37
interface. Pressing the SRC button can also switch

5 Tra ck 5
between the different sound source. USB
mus ic
Refer to navigation manual about the amazon music for 360 o

24 c 4
details.
Bluetooth Music
1 2 3 4 5
Please connect a Bluetooth device first before playing
Bluetooth music. Refer to "Bluetooth Pairing and 1 Track List
Connection" in "Settings" section for details. 2 Opening / Closing Track List
3 Previous Track
4 Play/Pause
5 Next Track
Note: Some mobile phones or bluetooth devices may
not support synchronized track lists, and the relevant
information will not be displayed in the play list bar.
103
USB Music 4 Play/Pause
Insert a USB storage device into the USB port, and the 5 Drag the progress bar to any playback point.
system automatically loads the music from the storage
6 Next Track
device.
Tra ck2 PAS S ENGER
AIRBAG 07:28 7 Touch to switch between single cycle mode, list cycle
P la y a ll Tota l of 40 mode and random play mode.
Tra ck 2
My fa vourite Artis t 2 BT
mus ic
Artis t 2’s s ong
Sound aduj s tme nt

Cla s s ica l mus ic
a ma zon
mus ic
P op mus ic 01:43 02:37
Othe rs
USB
mus ic
360 o
24 c 4
1 2 3 4 5 6 7
1 Track List
Touch to search for a song according to its name.
2 Touch to display the current lyrics.
3 Previous Track
104
Video Touch to search for video according to its name.
Insert a USB storage device into the USB port, touch 3 Short press to switch to the previous video; long press
[Video] in the main interface to enter the video playback to fast rewind.
interface.
4 Play/Pause
2
1
5 Short press to switch to the next video; long press to
fast forward.
6 Drag the progress bar to any playback point.
2 3 4 5 6
1 Touch to switch to full screen playback mode.
2 Play List
105
Vehicle-Mobile Phone Interconnection 4 After the vehicle and mobile phone are successfully
Note: Only the USB port on the driver's side can connected, you can operate the iPhone using the
support vehicle-mobile phone interconnection. entertainment system screen.
5 Press the HOME button on the control panel to return
Note: Due to the differences of mobile phone models
to the main system interface.
and system versions, some mobile phones may not be
able to use the vehicle-mobile phone interconnection Android Auto
function normally.
Android Auto enables information interaction between the
Apple CarPlay android mobile phone and the on-board entertainment
system, including map, music, telephone, voice commands
Apple CarPlay enables information interaction between the and so on.
mobile phone and the on-board entertainment system,
including map, music, telephone, voice recognition and so Ensure the Android Auto software is downloaded to your
on. phone using an APP from your regional APP supplier.
Ensure that the function is enabled.
Connection Method
1 Confirm that your iPhone has the Carplay function and Connection Method
that it is turned on. 1 Connect the mobile phone to the entertainment
system using an approved USB cable.
2 Connect the mobile phone to the entertainment
system mainframe using an approved USB cable. 2 In the main interface, touch the [Android Auto] area
to enter the Android Auto interface
3 In the main interface, touch [Apple CarPlay] area to
enter the Apple CarPlay interface.
106
3 Operate according to the interface prompts, you can Energy Management
then use the phone functions once the connection is
Touch the Energy Management area in the main interface
successful.
to enter the energy management interface. You can view
4 Press the HOME button on the control panel to return the current electricity information, charging settings, etc. 2
to the main system interface.
MG Touchpoint
Touch [MG Touchpoint] in the main interface to enter
the Maintenance interface. You can view the dealer
information.
Vehicle Setting
Touch [vehicle] in the main interface or the icon to enter
the vehicle settings interface. You can set the MG Pilot,
lights, etc., and can also view the vehicle information and
maintenance status.
107
Setting vehicle device using the phone to pair, after the pairing
is completed, the Bluetooth icon will show in the
Touch [Setting] in the main interface to enter the settings
status bar. If the pairing fails, please repeat the above
interface. You can set general settings, connection mode
steps.
and flow management.
The devices already paired and connected are displayed in
General the [Connected Currently] directory, only one Bluetooth
device can be connected to this system.
In the settings interface, touch [General] to enter the
general settings interface to set the screen brightness, time In the Bluetooth Connection interface, you can choose
, etc. whether or not to synchronize call history and contacts,
disconnect the currently connected device, and pair with
Bluetooth Pairing and Connection other devices in [Pairing history] or [Other devices]
The steps of Bluetooth pairing and connection are as according to your requirements.
follows:
WiFi Connection
• Touch [Bluetooth] in the settings interface to enter the
bluetooth interface, enable the Bluetooth function. WIFI connection steps are as follows:
• In the settings interface, touch [Wireless network],
Local name: displays the name of the vehicle, you can
enter the WIFI connection interface, and turn on the
customize the name , the name of the vehicle hotspot
WIFI switch.
will be updated synchronously after modification.
• Select the WIFI with which you want to connect in the
• The on-board mainframe will actively search for nearby
[Choose the Network] column to connect, or touch
Bluetooth devices that can be connected and show
[Add WiFi] to connect to a hidden WIFI by entering
them in [Other Devices], you can also search for the
the WIFI name, security type or password.
108
Note: For your information security, it is • Device Connected: displays the number of devices
recommended to select a WIFI connection with a high connected to the vehicle hotspot and the device
security level of WPA2. information.
Traffic Management 2
Hotspot Connection
In the settings interface, touch [Data traffic management]
In the settings interface, touch [Vehicle Hotspot], enter the
to enter the traffic management interface, you can turn the
vehicle hotspot interface, and turn on the Vehicle Hotspot
online network switch on or off and view the data usage.
switch.
• Vehicle name: displays the name of this vehicle, you can Voice
customize the name, the vehicle name on the vehicle
In the settings interface, touch [Voice] to enter the voice
Bluetooth will also be updated synchronously after
setting interface to set the voice broadcast language,
modification.
greetings, etc.
• Hotspot passcode: you can customize the vehicle
hotspot password, the password length should be Volume settings
greater than 8 characters.
In the settings interface, touch [Volume settings] to enter
• Hotspot network frequency band: you can choose
the volume setting interface to set the system sound,
2.4GHz or 5GHz. 2.4GHz supports more devices
chime, etc.
connected to the vehicle hotspot, but it is easy to
generate interference, 5GHz is the opposite, you can
set according to your needs.
109
System User Manual
In the settings interface, touch [System] to enter the In the settings interface, touch [User Manual] to enter the
system setting interface. You can view the software user manual interface. You can view the user manual and
version or upgrade the application software. entertainment manual.
Touch [Upgrade] to enter the upgrade interface and select
[Detect New Versions]. If the system detects a new
version, you can download and install the new software
version according to the interface prompt.
Note: For software version, map and voice upgrade
related functions, please consult an MG Authorised
Repairer.
Activation
In the settings interface, touch [Activation] to enter the
activation interface. If the activation process has not been
completed, you can activate it again here.
Privacy policy
In the settings interface, touch [Privacy policy] to enter the
privacy policy interface, where you can view the privacy
policy and choose whether to agree with it or not.
110
Seats & Restraints
112 Seats
117 Seat Belts
128 Airbag Supplementary Restraint 3
System
137 Child Restraints
SEATS & RESTRAINTS
Seats Head Restraints
Adjust the height of the head restraint so that
Overview
the top of it is in line with the top of the
To avoid personal injuries due to the loss of occupant's head. This location may reduce
control, DO NOT adjust the seats while the the risk of head and neck injuries in the event
car is moving. of a collision. DO NOT adjust or remove the
head restraints while the car is moving.
An ideal position of the seat should make sure your driving
position is comfortable, which allows you to hold the DO NOT hang anything on any head restraint
steering wheel with your arms and legs slightly bent and or head restraint rod.
control all the equipment. Make sure your driving position
is comfortable and enables you to maintain full control
The head restraint is designed to prevent rearward
of the vehicle. Take care when adjusting the height of
movement of the head in the event of a collision or
front seats - the feet of the rear passenger could become
emergency braking, thereby reducing the risk of head and
trapped when the seat is lowered.
neck injuries.
Do not incline the front-seat backrest excessively.
Optimum benefit is obtained from the seat belt with the
backrest angle set to approximately 25° from the upright
(vertical). The driver and front passenger seats should
be positioned as far rearward as practical. A properly
adjusted seat helps reduce the risk of injury from sitting
too close to an inflating airbag.
112
SEATS & RESTRAINTS
Front Seats
Manual Seat
When adjusting the head restraints from a low to high

position, pull the head restraint directly upward, and gently
press it downward after it reaches the desired position to 1
make sure that it is locked in position. To remove the 3
head restraint, press and hold the guide sleeve button (as
2
indicated by the arrow) on the left of the head restraint,
then pull the head restraint upward to remove it.
When adjusting the head restraints from a high to low
position, press the guide sleeve button (as indicated by the
arrow) on the left of the head restraint, and press the head
restraint downward; release the button after it reaches
the desired position, and gently press the head restraint
downward to make sure that it is locked in position.
113
SEATS & RESTRAINTS
*
• Forward/Backward Adjustment Power Seat
Lift the lever (1) under the seat cushion, slide the seat
into an appropriate position and release the lever. Make
sure that the seat is locked in place.
B
0
• Cushion Height Adjustment *
0
Lift the lever (2) repeatedly to raise the seat cushion,
and press the lever downward to lower the seat A
cushion.
• Backrest Adjustment
Lift the lever (3), adjust the backrest until it moves into
a satisfiable position , and put down the lever.
1 2
114
SEATS & RESTRAINTS
• Forward/Rearward Adjustment Rear Seats
Push the switch (1) forward or backward (A) to move
the seat forward/backward.
• Cushion Height Adjustment
Pull the switch (1) upward or push downward (B) to
raise or lower the seat cushion. 3
• Backrest Adjustment
Move the switch (2) forward/backward to adjust the
backrest until it reaches the desired angle.
To increase luggage space, the rear seat backrest can be

fully folded forward. When folding the backrest, first fully
lower (or remove) all the rear seat head restraints, and
then pull up the backrest unlock straps on both sides
respectively and fold the seat backrests forward.
To return the backrest to an upright position, raise the
rear seat backrest. When the desired upright position is
115
SEATS & RESTRAINTS
reached, a 'click' will be heard. Ensure the backrest is When pressing a seat heater switch, the corresponding
locked in position. seat will become warm. Press the switch again to stop
the heating function. When the seat heating function is
Note: When the head restraint of the rear seat is
activated, the operating indicator in the switch illuminates.
not fully lowered or the backrest of the front seat is
When the temperature reaches approximate 42℃, the
inclined backward excessively, the folding of the rear
heating function will be deactivated automatically.
seat is very likely to damage the back of the front seat,
small storage compartment or head restraint of the IMPORTANT
rear seat.
• DO NOT cover the heated seats with blankets,
Note: When returning the rear seat backrest to the cushions or other insulation type objects or
desired position, make sure that the rear seat belt is materials.
not trapped. • If the seat temperature has reached 42℃ and
continues getting hotter when using the seat heating
*
Front Seat Heating system, please turn off the seat heating and contact
If bare skin is in contact with the heated seats an MG Authorised Repairer.
for excessive periods of time, it may cause • Overuse of the driver's heated seat may cause
burns. drowsiness and could affect safety.
The seat cushion and backrest are provided with heating

elements. After the vehicle is set to READY mode, access
the air conditioning control interface and press the seat
heating switch to control the heating function of the
corresponding seat.
116
SEATS & RESTRAINTS
Seat Belts
It is important that all seat belts are worn This vehicle is equipped with a seat belt warning
correctly. Always check that all passengers lamp to remind you to fasten your seat belt.
are wearing seat belts. DO NOT carry During driving, seat belts must be fastened，this is because:
passengers that are unable to wear correctly • You can never predict if you will be involved in a collision
positioned seat belts. Wearing seat belts accident and how serious it may be.
incorrectly may cause serious injury or even • In many cases of collision accidents, passengers with
3
death in the event of a collision. seat belts properly fastened are well-protected, while
passengers with seat belts not fastened suffer from
Airbags can not replace seat belts. Airbags serious injury or even death.
can only provide extra support when
Therefore, all passengers must wear seat belts correctly,
triggered, and not all traffic accidents
even during short-distance journeys.
will trigger airbags. Whether airbags are
triggered or not, seat belts can reduce the
risks of serious injury or death in accidents. Protection Provided by Seat Belts
Therefore, seat belts must be worn properly. It is of equal importance for passengers in the
rear seat to fasten their seat belts correctly.
NEVER unfasten a seat belt whilst driving, Otherwise, passengers with seat belts not
serious injury or death may occur in the case correctly fastened will be thrown forward in
of an accident or emergency braking. accidents, and will endanger themselves as
well as the driver and other passengers.
117
SEATS & RESTRAINTS
When the vehicle is in motion, the travelling speed of the
occupants is identical to that of the vehicle.
In the event of a ‘head on collision’ or emergency braking,
the vehicle may stop, but the occupants will carry on
travelling until they come into contact with a stationary
object. This object may be the steering wheel, dashboard,
windscreen or front seats.
A correctly fastened seat belt will eliminate this risk of
injury. When the seat belt is worn correctly, it will lock
automatically in collision accidents or emergency braking
to reduce your speed together with the vehicle, so as
to prevent the out-of-control movement which may cause
serious injury to driver and passengers.
118
SEATS & RESTRAINTS
Wearing Seat Belts Seat belts cannot function correctly when the
seats are reclined excessively. DO NOT drive
Incorrectly worn seat belts could cause injury when the seats are excessively reclined.
or death in the event of an accident.
The seat belts fitted to your vehicle are designed for use
Seat belts are designed for one person, DO by normal sized adults. This part of the literature refers to
NOT share seat belts. adult use. 3
All seat belts are 3 point lap-diagonal belts.
DO NOT wrap a seat belt around when In order to maintain effective protection, the passengers
holding a baby or child in your arms. must sit in the correct orientation, feet placed on the floor
in front of them, with an upright body (no excessive recline)
Remove any heavy coats or clothing when and the seat belt correctly fastened.
wearing a seat belt, failure to do so can affect
protection provided by the seat belt.
Seat belts should not be wrapped around

hard or sharp objects such as pens, spectacles
or keys.
119
SEATS & RESTRAINTS
Fastening Seat Belts
Please follow the instructions below to fasten the seat belts
correctly.
1 Adjust the seat correctly.
2 Hold the metal tab, pull the seat belt out steadily over
the shoulder and across your chest. Ensure there is no
twist on the belt.
4 Remove any slackness in the belt by pulling up on the

diagonal section of the belt.
5 To release the seat belt, press the red button on the
buckle. The seat belt will retract automatically to its
original place.
3 Insert the metal tab into the buckle until you hear a
'click', this indicates the seat belt is securely locked.
120
SEATS & RESTRAINTS
IMPORTANT Correct Routing of the Seat Belts
• Always ensure the seat belt will not become trapped Ensure the seat belt is correctly positioned on
in the door aperture when closing the door, damage the body, never cross the neck or abdomen,
will occur. never pass the seat belt behind the back or
• Pulling the seat belt out too quickly may cause it under the arms.
to lock. In this case, allow the seat belt to retract
slightly and then pull it across your body slowly.
3
• If it is difficult to pull the seat belt out, it may be due
to twisted webbing. If this is the case, fully extract
the seat belt, remove the twist, allow the seat belt
to retract slowly.
• When using the rear seat belts please ensure they
are fully retracted into the correct position to avoid
jamming in the rear seat catches. Even if the seat
belt is twisted, it is still required to be worn during
driving, but the twisted part of the seat belt should
not contact the passenger. When this happens,
please go to an MG Authorised Repairer for repair.
When wearing seat belts, the lap belt section should be
positioned as low as possible across your hips, never across
the abdomen. In the event of a collision, the lap belt can
apply a force on the hips and reduce the possibility of you
121
SEATS & RESTRAINTS
slipping under the lap belt. If you slip under the lap belt, the
belt will apply force on your abdomen, which may cause
serious or fatal injuries. The diagonal section of the belt
should cross the middle of the shoulder and the chest. In
the event of emergency braking or collision, the diagonal
section of the belt will be locked.
To ensure that the seat belts always provide maximum
protection, ensure the belt is flat, not loose and contacts
the body.
Seat Belts Use during Pregnancy

The diagonal section of the seat belt should pass across
Wearing correctly positioned seat belts will provide the chest as normal, the lap section of the belt should pass
protection for both mother and unborn child in the event below the belly, low and snug on the hip bones. NEVER
of a collision or emergency braking. position the belt on or above the belly.
Please consult your physician for further details.
Seat Belts and Disabilities

It is a legal requirement that all occupants wear seat belts,
this include people with disabilities.
Depending upon the disability, consult your physician for
further details.
122
SEATS & RESTRAINTS
Children and Seat Belts Infants MUST use a suitable child restraint device. Please
Proper protection measures must be taken consult the child seat manufacturer’s guidelines when
for children during driving. selecting the correct seat. Follow the manufacturer’s
instructions on installation. Please refer to "Child
For safety reasons, children must travel in a child restraint Restraints" in this chapter for more details.
device fixed to the rear seat.
Older Children 3
Infants NEVER share a seat belt amongst children.
Only recommended child restraints suitable In the event of an accident or collision, the
for the age, height and weight of the child children are not secure. It could cause death
should be used. or serious injury.
NEVER carry a child or infant with your arms
during driving. When collision accidents
occur, the weight of the child will produce
so great of a force that you will not be able
to hold on to the child. The child will be
thrown forward and suffer serious injury or
even death.
The seat belts fitted to your vehicle are designed for adults,
they are not suitable for children. In the event of an
accident or collision the children are not secure, it could
cause death or serious injury.
123
SEATS & RESTRAINTS
As children grow and become older/larger it will get to the Seat Belt Pre-tensioners
stage when they no longer require child seat restraints. At
The seat belt pre-tensioners will only
this point they will require use of the vehicle standard seat
be activated once and then MUST
belt. Please ensure the seat belt is correctly positioned on
BE REPLACED. Failure to replace the
the body of the child.
pre-tensioners will reduce the efficiency of
When fastening a seat belt for a child always check it for the vehicle's restraint system.
correct positioning. Adjust the height of the seat belt to
ensure the shoulder belt is kept away from the child's face If the pre-tensioners have been activated, the
and neck. Position the lap belt across the hips as low seat belts will still function as restraints, and
as possible, and tighten adequately. Correct positioning must be worn in the event that the vehicle
means that the seat belts can pass the applied force to the remains in a drivable condition. The seat
strongest part of the child's body in accidents. belt pre-tensioners should be replaced at the
earliest opportunity by an MG Authorised
If the shoulder belt is too close to the child's face or neck,
Repairer.
it may be necessary to use a child booster cushion (always
ensure that it meets any relevant laws or standards).
The vehicle is fitted with seat belt pre-tensioners. These
are designed to retract the seat belts and work in
conjunction with the airbags in the event of a severe
collision. They are designed to retract the seat belt and
'secure' the occupant in the seat.
The airbag warning light on the instrument pack will
alert the driver to any malfunction of the seat belt
124
SEATS & RESTRAINTS
pretensioners.(see ‘Warning Lights and Indicators' in the Seat Belt Checks, Maintenance and
‘Instruments and Controls’ chapter). Replacement
The seat belt pre-tensioners can only be activated once. Seat Belt Checks
After activation they must be replaced. This may also
involve replacement of other SRS components. Please Split, worn or frayed seat belts may not
refer to 'Replacing Airbag System Parts'. function correctly in the event of a collision,
if there are any signs of damage, replace the 3
IMPORTANT belt immediately.
• Seat belt pre-tensioners will not be activated by
Always ensure the red release button on the
minor impacts.
seat belt buckle is pointing upwards to ensure
• The removal or replacement of a pre-tensioner must
easy release in the event of an emergency.
be carried out by the technicians trained by the
manufacturer.
Please follow the instructions below to check the seat belt
• 10 years from the initial date of registration warning lamp, seat belt, metal tab, buckle, retractor and
(or installation date of a replacement seat belt fixing device regularly:
pre-tensioner), some components will need to
• Insert the seat belt metal tab into the corresponding
be replaced. The appropriate page of the Service
buckle and pull seat belt webbing close to the buckle
Records must be signed and stamped once the work
quickly to check that the belt clasp locks.
has been completed.
• Hold the metal tab and pull the seat belt forward quickly
to check that the seat belt reel locks automatically,
preventing the webbing from extending.
125
SEATS & RESTRAINTS
• Fully extract the seat belt and visibly examine for twists, Ensure no foreign or sharp objects become
fraying, splits or worn areas. lodged in the seat belt mechanisms. DO
• Fully extract the seat belt and allow to return slowly to NOT allow liquids to contaminate the seat
ensure continual and complete smooth operation. belt buckle, this could affect the buckle
• Visibly examine the seat belt for missing or broken engagement.
components.
• Ensure the seat belt warning system is fully functional. Seat belts should only be cleaned with warm soapy water.
DO NOT use any solvent to clean the seat belt. DO NOT
If the seat belt fails any of the above tests or inspections,
attempt to bleach or dye the seat belt, it may weaken the
contact an MG Authorised Repairer immediately for
seat belt. After cleaning, wipe with a cloth and allow to
repairs.
dry. DO NOT allow the seat belt to fully retract before it
Seat Belts Maintenance is completely dry. Keep seat belts clean and dry.
DO NOT attempt to remove, install, modify, If there are contaminants accumulated in the retractor, the
disassemble or dispose of the seat belts. Have retraction of the seat belt will be slow. Please use a clean
any necessary repairs carried out by your MG and dry cloth to remove any contaminants.
Authorised Repairer. Inappropriate handling
may lead to incorrect operation.
126
SEATS & RESTRAINTS
Replacing Seat Belts
Collision accidents may damage the seat belt
system. The seat belt system may not be able
to protect users after damage, which may
result in serious injury or even death. After
an accident, seat belts should be checked and
replaced as needed immediately. 3
Seat belts should not require change after minor collisions,
however, some other parts of the seat belt system may
require attention. Please consult an MG Authorised
Repairer for advice.
127
SEATS & RESTRAINTS
Airbag Supplementary Restraint • Seat Side Airbags (fitted to the outer side of the seat
System squab)
• Side Head Impact Protection Airbags (fitted behind the
Overview headlining)
The airbag SRS provides ADDITIONAL • Airbag Control Module
protection in a severe frontal impact only. It Please note that this is model and trim level dependant.
does not replace the need, or requirement to
wear a seat belt.
The airbags together with the seat belts

provide optimum protection for adults, but
it is not the case for infants. The seat
belt and airbag systems in the vehicle are
not designed for protecting infants. The
protection required by infants should be
provided by child restraints.
The Airbag Supplementary Restraint System generally

consists of:
• Front Airbags (fitted to the centre of the steering wheel
and dashboard above the glove compartment)
128
SEATS & RESTRAINTS
In the corresponding position where airbags are fitted, Airbag Deployment
there is a warning sign stating ‘AIRBAG’.
Front seat passengers should not place feet,
Airbag Warning Light knees or any other part of the body in contact
with, or in close proximity to a front airbag.
The airbag warning light is located in the To minimise the risk of accidental injury from
instrument pack. If this lamp does not extinguish or inflating airbags, seat belts should be worn 3
illuminates during driving, it indicates that there is a failure correctly at all times. In addition, both driver
in the SRS or seat belt. Please seek an MG Authorised and front seat passenger should adjust their
Repairer at the earliest opportunity. An SRS or seat belt seat to provide sufficient distance from the
fault may mean the components may not be deployed in front airbags. If side airbags/side head impact
the event of an accident. protection airbags are fitted, both driver and
front seat passenger should be seated to
maintain sufficient distance from the upper
part of the body to the sides of the vehicle,
this will ensure maximum protection when
the side airbags/side head impact protection
airbags are deployed.
129
SEATS & RESTRAINTS
When airbags are deployed, children without DO NOT knock or strike the position where
proper protection may suffer from serious airbags or related parts are located, so as
injury or even death. DO NOT carry children to avoid accidental airbag deployment which
in the arms or on the knees during traveling. may cause serious injury or even death.
Children should wear seat belts suitable to
age. DO NOT lean out of windows. In the event of a collision, the airbag control unit monitors
the rate of deceleration or acceleration induced by the
An inflating airbag can cause facial abrasions collision, to determine whether the airbags should be
and other injuries if the occupant is too close deployed. Airbag deployment is virtually instantaneous
to the airbag at the time of its deployment. and occurs with considerable force, accompanied by a
loud noise.
DO NOT affix or place any objects on, or
Provided the front seat occupants are correctly seated and
adjacent to the airbags. This may affect the
with seat belts properly worn, the airbags will provide
airbag passage or create projectiles that may
additional protection to the chest and facial areas in the
cause injury or serious harm in the event of
event of the car receiving a severe frontal impact.
airbag deployment.
Side airbags and side head impact protection airbags are
After deployment the airbag components designed to offer additional protection to the side of the
become very hot. DO NOT touch any airbag body facing the impact, if a severe side collision occurs.
related components, it may cause burns or
serious injury.
130
SEATS & RESTRAINTS
IMPORTANT Front Airbags
• Airbags cannot protect lower body parts of NEVER use a rearward facing child restraint
passengers. on a seat protected by an ACTIVE AIRBAG
• Airbags are not designed for rear collision, minor in front of it, DEATH or SERIOUS INJURY to
frontal or side impacts, or if the vehicle overturns; the CHILD can occur. Refer to ‘Disabling the
nor will it operate as a result of heavy braking. Passenger Airbag'.
• Deployment and retraction of the frontal and side
3
Front seat passengers should not place feet,
airbags takes place very quickly and will not protect knees or any other part of the body in contact
against the effects of secondary impacts that may with, or in close proximity to a front airbag.
occur.
• When an airbag inflates, a fine powder is released. In extreme cases driving on very uneven
This is not an indication of a malfunction, however, surfaces may cause airbag deployment.
the powder may cause irritation to the skin and Please take extra care when driving on
should be thoroughly flushed from the eyes and any uneven roads.
cuts or abrasions of the skin.
• After inflation, front and side airbags deflate Airbags are designed to deploy during serious impacts, the
immediately. This provides a gradual cushioning following conditions may cause airbag deployment.
effect for the occupant and also ensures that the • A frontal collision with unmovable or non deformable
driver's forward vision is not obscured. solid objects at a high speed.
• Conditions that can cause serious chassis damage, such
as a collision with kerbstones, road edges, deep ravines
or holes.
131
SEATS & RESTRAINTS
Seat Side Airbags Conditions in Which Airbags Will Not
The manufacture and material of the seat Deploy
is critical to the correct operation of side The deployment of airbags does not depend on the vehicle
airbags. Therefore, please DO NOT fit speed, but on the object that the vehicle hits, angle of
seat covers which may affect side airbag impact and the rate at which the car changes speed as a
deployment. result of a collision. When the impact force of collision
is absorbed or dispersed to vehicle body, airbags may not
In the event of a serious side impact, the relevant side airbag
deploy; however, airbags may sometimes deploy according
will deploy (only the affected side).
to impact condition. Therefore, the deployment of airbags
• The airbag will be deployed in the event that the side of
shall not be judged based on the severity of vehicle damage.
the vehicle is impacted with a solid object or another
vehicle. Front Airbags
Side Head Impact Protection Airbags Under certain conditions the front airbags may not be
In the event of a serious side impact, the relevant side deployed. Some examples are listed below:
curtain airbag will deploy (only the affected side). • The impact point is not central to the front of the
• The side curtain airbag will be deployed in the event that vehicle.
the side of the vehicle is impacted with a solid object or • The impact is not of sufficient force (the impact is with
another vehicle. an object that is not solid, such as a lamp post or central
barriers).
• The impact area is high (collision with the tailgate of a
truck).
• Impacts to the rear or side of the vehicle.
132
SEATS & RESTRAINTS
• The vehicle rolling over. Disabling the Passenger Airbag
• Frontal collision at an angle with guard bars. The Passenger Airbag should only be disabled
Seat Side Airbags and Side Head Impact when a rear facing child seat is fitted to the
front passenger seat.
Protection Airbags
Under certain conditions the seat side and side head When an adult is seated in the front
airbags may not be deployed. Some examples are listed passenger seat, ensure that the airbag is 3
below: switched on.
• Side impacts at certain angles.
• Light side impacts such as a motorcycle.
• Impacts that are not central to the side of the vehicle,
either too far toward the front compartment or the
loadspace.
• The vehicle rolling over.
• Frontal collision at an angle with guard bars.
• The angled impact is not of sufficient force (the impact
is with an object that is not solid, such as a lamp post
or central barriers).
• The impact is not of sufficient force (with another
vehicle, stationary or moving).
• The impact is from the rear of the vehicle.
133
SEATS & RESTRAINTS
The passenger airbag disable switch is located inside of the When the switch is turned to the OFF position, the OFF
glovebox, Insert the key and turn the switch to the on or indicator light ( located in the PAB display panel in the lamp
off position to enable or disable the passenger airbag. assembly ) illuminates, this indicates that the passenger
airbag is disabled.
When the switch is turned to the ON position, the ON
indicator light ( located in the PAB display panel in the lamp
assembly ) illuminates, this indicates that the passenger
PA S S E N G E R A IR B A G airbag is enabled.
O FF O N
PA S S E N G E R A IR B A G
O FF O N
The passenger airbag status light is located in the roof

mounted interior lamp assembly. The shape of the lamp
assembly varies according to the configuration of the
vehicle.
134
SEATS & RESTRAINTS
Service and Replacement of Airbags • Steering wheel centre pad.
• Area of dashboard containing the passenger airbag.
Service Information
• Area of roof lining and front pillar finishers which
DO NOT install or modify the airbag. Any enclose the side head impact protection modules.
changes to the vehicle structure or airbag If the airbag warning lamp fails to illuminate, stays on, or
system wiring harness are strictly prohibited. if there is damage to the front or side of the vehicle, or
the airbag covers show signs of damage, contact an MG 3
Changes to vehicle structure is prohibited. Authorised Repairer immediately.
This may affect the normal operation of the
SRS. IMPORTANT
• The removal or replacement of an airbag module

DO NOT allow these areas to be flooded with should be carried out by an MG Authorised Repairer.
liquid and DO NOT use petrol, detergent,
• After 10 years from the initial date of registration
furniture cream or polishes.
(or installation date of a replacement airbag), some
components will need to be replaced by an MG
If water contaminates or enters the SRS it
Authorised Repairer. The appropriate page of the
may cause damage and affect deployment.
Service Portfolio must be signed and stamped once
In this case contact an MG Authorised
the work has been completed.
To prevent damage to the airbag SRS, the following

areas should be cleaned sparingly with a damp cloth and
upholstery cleaner ONLY:
135
SEATS & RESTRAINTS
Replacing Airbag System Parts If the vehicle is scrapped, the undeployed airbags may have
potential risks, therefore, before the disposal, they must be
Even if the airbag does not deploy, collisions
deployed safely in a certain environment by a professional
may cause damage to SRS in the vehicle.
agency or an MG Authorised Repairer.
Airbags may not function properly after
damage, and can not protect you and other
passengers when a second collision occurs,
which may cause serious injury or even
death. To ensure that SRS can function
properly after collision, please go to an MG
Authorised Repairer to check airbags and
repair as necessary.
Airbags are designed for using once only. Once the airbag
is deployed, you must replace SRS parts.
Please go to an MG Authorised Repairer for replacement.
Disposal of Airbags
When your vehicle is sold, ensure that the new owner
knows the vehicle is equipped with airbags, and is aware
of the replacement date of SRS.
136
SEATS & RESTRAINTS
Child Restraints serious injury to the child in an event of a sudden stop or
accident.
Important Safety Instructions about Using • All occupants, including children must wear seat belts
Child Restraints or use an appropriate child restraint.
It is recommended that children below the age of 12 years • It is recommended that children under 12 years of age
old should be seated on the rear seat of the vehicle, in a or less than 1.5 metres tall should use the appropriate
child restraint system appropriate to the children's weight child restraint fitted to the rear seat. 3
and size. Infants less than 2 years old should be restrained • Only one child can be carried in any one restraint.
in an infant child restraint system. • Do not put the child on the lap or in arms when sitting
It is recommended that a child restraint system that in any seat.
complies with UN ECE-R44 or ECE-R129 standard are • Always adjust the seat back rest to a central position
fitted in this vehicle. Check markings on the child restraint and ensure it is locked in position when installing a child
system. seat or restraint.
There are a number of child restraint systems available of • If installing a rear facing child restraint to the rear
different type and specification. For optimum protection, seat, the corresponding front seat should be adjusted
it is recommended that you choose restraint systems forward; if installing a forward facing child restraint
appropriate to the child’s age and weight. to the rear seat, you may need to adjust the height
of the headrest to the lowest; if installing a forward
It is important to comply with installation instructions facing child restraint to the front seat, you may need to
supplied by the child restraint manufacturer and that any remove its headrest.
child restraint system is properly secured to the vehicle. • Never let your child stand or kneel on the seat during
Failure to follow these instructions may cause death or driving.
137
SEATS & RESTRAINTS
• Always ensure the child is seated correctly in the child Warnings and Instructions on Use of Child
restraint. Restraint on Front Passenger Seat
• The ways of using seat belts have a great influence on
the maximum protection offered by the seat belt, you
must comply with the child restraint manufacturer's
instructions on proper use of seat belts. If seat belts
AIRBAG
are not properly fastened, a minor traffic accident may
also lead to injury.
• Child restraints that are not fitted correctly may move
and injure other occupants in the event of an accident
or emergency braking. Therefore, even if there is no
infant or child in the child restraint, it also should be
fitted properly and securely in the vehicle. NEVER use a rearward facing child restraint
on a seat protected by an ACTIVE AIRBAG
in front of it, DEATH or SERIOUS INJURY to
the CHILD can occur.
In cases where there is a need to install a rear

facing child restraint on the front passenger
seat, use the key to deactivate the front
passenger airbag function, or severe injury
or even death can occur.
138
SEATS & RESTRAINTS
Once the child restraint is removed from the Only recommended child restraints suitable
front passenger seat, use the key to reactivate for the age, height and weight of the child
the front passenger airbag. should be used.
When installing a child restraint on the front DO NOT place any items in areas where
passenger seat, move the front passenger airbags may be deployed, there is a risk of
seat as far rearward as possible. serious injury. 3
In the event of a side collision, the side airbags can provide
Use one child restraint per child. better protection for the passenger. However, when
the airbag is triggered a very strong expansion force is
generated, if the passenger's seating position is not correct,
Please study the safety warning label on the sun visor.
the airbags or items in the side airbag deployment area
Where possible always install child restraints on the rear
may cause injury.
seat. If it is necessary to install a child restraint on the front
seat please observe the warnings above. When the correct child restraint is used to secure the
child properly in the rear seat and the child's seating
Children's Safety and Side Airbags position is correct, there is enough space between the
Children should not be allowed in areas child and the side airbag deployment region for the airbag
where airbags may be deployed, there is a to deploy without any hindrance, and thus provide the
risk of serious injury. best protection.
139
SEATS & RESTRAINTS
Child Restraints Groups ISOFIX Child Restraint Systems
Secured Using 3 Point lap Diagonal Belts The ISOFIX anchorages in the rear seat are
Please DO NOT put the rear facing child designed for use with ISOFIX systems only.
restraint in the front passenger seat, this may
cause serious injury or even death. Child restraint anchorages are designed
to withstand only those loads imposed by
correctly fitted child restraints. Under no
circumstances are they to be used for adult
seat belts, harnesses, or for attaching other
items or equipment to the vehicle.
Note: When installing and using any child restraint

system, always follow the manufacturer's instructions.
Note: The rear seats fitted to this vehicle are provided

with the ISOFIX interface (as indicated by the arrow in
the following image), these are designed to connect to
an ISOFIX child seat.
It is recommended that children should always be seated
1 Fasten vehicle-approved ISOFIX child restraint
in the rear of the vehicle in a child restraint or restraint
systems to the mounting brackets.
system，and fixed with 3 point, lap diagonal seat belts.
2 When using ISOFIX mounting brackets for seat
mounting, universally approved child restraint systems
for ISOFIX may be used.
140
SEATS & RESTRAINTS
Note: When using seat mounting, universally
approved child restraint systems, Top-tether must
be used.
4 After installation apply suitable force to ensure the
restraint is securely fastened.
T O P T E T H E R
3 To fasten the top tether strap of the child restraint

system, route the tether strap under the head restraint
and attach to the anchorage hook being careful not to T O P T E T H E R
T O P T E T H E R
twist the strap. If not using ISOFIX lower anchorages,

using the seatbelt, complete the installation in line with
the child restraint manufacturers instructions.
141
SEATS & RESTRAINTS
Approved Child Restraint Positions
It is recommended that a child restraint system that complies with UN ECE-R44 or ECE-R129 standard are fitted in this
vehicle. Check markings on the child restraint system.
Approved Child Restraint Positions (for non ISOFIX Child Restraints)

Seating Positions
Front Passenger
Mass Group
With Front Passenger Airbag OFF Switch Rear Outboard Rear Middle
Airbag ON Airbag OFF
0 group (less than 10 kg) X U U U
0+ group (less than 13 kg) X U U U
I group (9～18 kg) X U U U
II group (15～25 kg) X U U U
III group (22 ～ 36 kg) X U U U

Note: Description of letters in the table:
U = Suitable for universal child restraint systems approved for this mass group;
X = Seat position not suitable for child restraint systems in this mass group.
142
SEATS & RESTRAINTS
Approved Child Restraint Positions (for ISOFIX Child Restraints)
Mass group categories
0 group 0+ group I group

Seating Position
Rear facing Forward facing Rear facing
Up to 29 lbs(13 kg) 20–40 lbs(9～18 kg) 3
Front Passenger Size Class
Not ISOFIX equipped
Seat Seat Type
Rear Outboard Size Class C,D,E1 A,B, B11 C,D1

Seat ISOFIX Seat Type IL2 IL2,IUF3 IL2
Size Class
Rear Centre Seat Not ISOFIX equipped
Seat Type
Note: IL Suitable for particular ISOFIX child restraints systems of the semi-universal category. Please consult child restraints
systems suppliers' vehicle recommendation lists;
IUF Suitable for ISOFIX forward facing child restraints systems of universal category approved for use in this mass group
and ISOFIX size class;
1
. The ISOFIX size class for both universal and semi-universal child seat systems is defined by the capital letters grade A～
G. These identification letters are displayed on the ISOFIX child seat;
143
SEATS & RESTRAINTS
2
. At time of publishing the recommended Group 0+ ISOFIX baby safety seat is the Britax Romer Baby Safe;
3
. At time of publishing the recommended Group I ISOFIX child seat is the Britax Romer Duo.
Note: At time of publishing the recommended Group II-III ISOFIX child seat is the KidFix II XP SICT.
Table of I- Size child seats
The table gives a recommendation for which I- Size child seats suit which locations, and for what size of child.
The child seat must be approved in accordance with UN Reg R129.
Type of child seat Front passenger seat Rear outboard seats Rear centre seat
I- Size child restraint systems X I-U X

Note: I-U Suitable for use with forward and rear facing I- Size child restraint systems.
X Not suitable for use with I- Size restraint systems.
144
SEATS & RESTRAINTS
Group 0/0+ Child Restraint Group I Child Restraint
When the front passenger airbag is active, When the front passenger airbag is active,
never place a rear facing child restraint on never place a rear facing child restraint on
the front passenger seat, severe injury or even the front passenger seat, severe injury or even
death can occur. death can occur.
Child restraints that can be adjusted to lying position

are most suitable for infants who are lighter than 10 kg
(normally for those younger than 9 months) or those who Backward/forward child restraints are most suitable for
are lighter than 13 kg (normally for those younger than 24 infants whose weight is 9～18 kg (normally for those older
months). than 9 months and younger than 4 years old).
145
SEATS & RESTRAINTS
Group II Child Restraint Group III Child Restraint
The diagonal section of the seat belt should The diagonal section of the seat belt should
pass across the shoulder and upper body, pass across the shoulder and upper body,
away from the neck. The lap section of the away from the neck. The lap section of the
belt should pass across the hips, away from belt should pass across the hips, away from
the abdomen. the abdomen.
The combination of child restraint and 3 point lap diagonal

The combination of child booster seat and vehicle 3 point
seat belt is most suitable for children whose weight is
lap diagonal seat belt is most suitable for children whose
15～25 kg (normally for those older than 3 years old and
weight is 22 ～ 36 kg and whose height is below 1.5 m
younger than 7 years old).
(normally for those about 7 years old or those older than
7 years old).
146
Starting & Driving
148 Keys 224 Tyre Pressure Monitoring System
(TPMS)
151 Child Proof Locks
225 Driving Assist System
152 Alarm System
242 Load Carrying
160 Starting and Stopping the Power
System
4
164 Pedestrian Alert Control System
165 Economical and Environmental Driving
168 Charging and Discharging
Requirements
186 Electric Drive Transmission
195 Brake System
206 Adaptive Cruise Control System
215 Parking Aid System
218 Rear Driver Assistance System *
STARTING & DRIVING
Keys
Overview
Please keep the spare key in a safe place - not
in the car!
It is recommended that spare keys are not
kept on the same key ring, since this may
cause interference and prevent correct key
recognition and therefore prevent the correct
operation of the vehicle power system. 1 Lock Button
The smart key contains delicate circuits and 2 Tailgate Button
must be protected from impact and water
3 Unlock Button
damage, high temperature and humidity,
direct sunlight and the effects of solvents, 4 Smart Key
waxes and abrasive cleaners. The smart key only works within a certain range. It's
Your vehicle is supplied with two smart keys, each one working range is sometimes influenced by the key battery
contains a back up mechanical key blade, this will operate condition, physical and geographical factors. For safety
the driver door mechanical lock. The smart keys supplied consideration, after you lock your vehicle by the smart key,
are programmed to the security system on the car, any key please recheck if the vehicle is locked.
that is not programmed to the car will not operate the If your key is lost/stolen or broken, a replacement can be
keyless entry function or the vehicle immobiliser. obtained from an MG Authorised Repairer. The lost/stolen
148
STARTING & DRIVING
key can be deactivated. If the lost key is found, an MG
Authorised Repairer can reactivate it.
A B
Note: Any key made privately may not start the
vehicle, and may affect the safety of your car. To
obtain a suitable key replacement, it is recommended
that you can consult an MG Authorised Repairer.
Note: The new key cannot be offered to you C D

immediately because it requires programming to the
vehicle by the MG Authorised Repairer. 4
Note: Avoid operating the smart key close to
strong radio interference devices (such as notebook
computers and other electronic products), the normal
function of the key may be affected. 1 Press the button (A) on the smart key to eject the
decorative trim.
Replacing the Battery 2 Remove the backup mechanical key (B) in the arrowed
Please use the picture guide to replace the smart key direction.
battery if any of the following conditions occur: 3 Using a suitable flat bladed tool, insert the tool into
• The smart key locking/unlocking function range is the side of the key (C), carefully prise off the battery
reduced; cover and separate the upper and lower casings (D).
• The message centre will display "Remote Key Low
4 Remove the battery from the slot.
Battery, Please Replace".
149
STARTING & DRIVING
5 Put the new battery in the slot, and make sure it is in IMPORTANT
full contact with the slot.
• Use of an incorrect or inappropriate battery may
Note: Make sure that the polarity of battery is damage the smart key. The new replacement’s rated
correct ('+' side facing down). voltage, sizes and specifications must be the same as
the old one.
Note: It is recommended to use a CR2032 battery. • Incorrect fitting of the battery may damage the key.
6 Refit the cover and press tightly, ensuring the gap • Disposal of the used battery must be strictly in
around the cover is even. accordance with relevant environmental protection
acts.
7 Refit the mechanical key, and refit the decorative trim.
8 Operate the vehicle power system to resynchronize
the key with the vehicle.
150
STARTING & DRIVING
Child Proof Locks • Open the rear door on the corresponding side, move
NEVER leave children unsupervised in the the child proof lock lever to the lock position in the
vehicle. direction of the arrow to engage the child proof lock;
• Move the lever to the unlock position in the reverse
direction of the arrow to disable the child proof lock.
With the child proof lock locked, the rear door on the
corresponding side cannot be opened from inside the car,
but can be opened from outside the car.
Steps for enabling or disabling the child proof locks are as

follows:
151
STARTING & DRIVING
Alarm System If the car can still not be started, please contact MG
Your car is fitted with an electronic anti-theft alarm and
power immobilisation system. To ensure maximum safety
and operation convenience, we strongly recommend you
to carefully read this chapter to fully understand the
activation and deactivation of anti-theft systems.
Power Immobilisation
Power Immobilisation is designed to safeguard the vehicle
from theft. The power immobilisation system can only be
deactivated to start the car by using the matched key.
Press the START STOP button on the instrument panel,
once a valid key is detected in the vehicle, immobilisation
system will be deactivated automatically.
If the message centre displays "Smart Key Not Detected" or
"Put Key Into Back-up Position" or the power immobiliser
system warning lamp illuminates, please put the smart key
at the bottom of the centre console cup holder (refer to
"Alternative Starting Procedure" in "Starting and Stopping
the Power System" section), or try to use the spare key.
152
STARTING & DRIVING
Body Anti-theft System tool, insert the tool into the underside of the trim and
carefully remove the driver door lock trim cover, insert
Locking and Unlocking the key into the driver door lock and turn clockwise
When the vehicle is locked, the indicator lamps flash three to unlock the car.
times; when it is unlocked, the indicator lamps flash once.
Find My Car
Operation of Door Lock System (Key) After the vehicle has been left in a locked condition for a
Key Locking few minutes pressing the lock button again on the remote
• Using the remote key to lock: press the lock button on key will enable the Find My Car function. This function
the key to lock the car after closing the doors, bonnet will identify the car by means of an audible and visual alert. 4
and tailgate. Pressing the Lock button on the handset again will suspend
this operation. Pressing the Unlock button will cancel this
• Using the mechanical key to lock: partially operate
operation. This feature can be set on the entertainment
the door release handle, using a suitable flat blade
display.
tool, insert the tool into the underside of the trim and
carefully remove the door lock trim cover, insert the Note: If the vehicle power system is not switched to
key into the driver door lock and turn counterclockwise the ACC/ON/READY position within 15 seconds after
to lock the car. the vehicle is unlocked with the mechanical key, the
immobilisation alarm will be triggered.
Key Unlocking
• Using the remote key to unlock: press the unlock Note: If no panels are opened within a few seconds
button on the key to unlock the car. after the vehicle is unlocked by using the remote key,
• Using the mechanical key to unlock: partially operate all doors will automatically re-lock.
the door release handle, using a suitable flat blade
153
STARTING & DRIVING
Operation of Door Lock System (Keyless) Keyless Locking
The keyless entry system can lock and unlock the doors After switching the START/STOP Switch to the OFF
and tailgate as long as you carry the smart key and approach position and exiting the car, press the door handle button
to the car. once before moving away from the car to lock all doors
and tailgate (no need to press the lock button on the
key). Note, this will also arm the alarm and immobilise
the vehicle.
Keyless Unlocking
Press the button on the front door handle once to unlock
the car, then pull the door handle to open the door.
Note: When the vehicle is locked, if you are within the
smart key range and operate the door handle button,
but carry out no further action, after 30 seconds
the vehicle will automatically re-lock itself to remain
secure.
IMPORTANT
The smart key must be within 1.5 metres of the vehicle

for the keyless system to operate correctly.
154
STARTING & DRIVING
IMPORTANT Inadvertent Locking of Keys in Vehicle
After the door is locked by using the key, press the If the vehicle is locked using the mechanical key blade or
button on the door handle to unlock the car. If the car handset whilst a smart key/s remain inside, the following
cannot be unlocked or locked normally, seek an MG actions will occur:
Authorised Repairer. • One smart key locked in the vehicle - The
immobilisation release function of the smart key locked
Mislock in the vehicle is suspended, the lock and unlock function
of the smart key is retained. The vehicle will not change
If the driver's door is not fully closed when the smart key power state. To reinstate the immobiliser release
lock button is pressed, or the START/STOP Switch has function of the smart key locked in the vehicle the
4
not been switched OFF, the vehicle horn will sound once, second smart key should be used to unlock the vehicle.
indicating a mislock. In this case, none of the doors will The function will automatically be reinstated.
lock, the alarm system will not be armed. • Both smart keys locked in vehicle - The immobilisation
If the driver's door is closed, the passenger door, bonnet release function of both smart keys locked in the vehicle
and tailgate are not fully closed, the horn sounds once to is suspended, the lock and unlock function of the smart
indicate mislock when the car undergoes locking operation. keys is retained. The vehicle will not change power
However, the ‘partial arming’ attributes of the security state. The reinstatement of key functions can only be
system will enable as much of the system to be armed as carried out using the approved diagnostic tool. Consult
possible (all fully closed doors, bonnet or tailgate apertures an MG Authorised Repairer immediately.
will be protected, but an open door will not!). The alarm
indicator will flash. As soon as the open aperture is closed,
the system will automatically revert to an armed state
155
STARTING & DRIVING
Anti-theft Alarm Sounder Interior Lock and Unlock Switch
If the anti-theft alarm has been triggered, the car horn will
sound continuously. Press the UNLOCK button on the
key, the anti-theft alarm will be deactivated.
1 Lock Switch
2 Unlock Switch
When the anti-theft alarm system is not in operation, press
the lock switch (1) to lock all doors; press the unlock
switch (2) to unlock all doors.
156
STARTING & DRIVING
Note: If the anti-theft alarm system is switched on, Interior Door Handles
pressing the lock/unlock button will not lock/unlock
When the anti-theft alarm system is not in operation, use
the doors but will trigger the alarm system.
the interior door handle to open the door:
If the doors, bonnet and tailgate are closed, press the 1 Pull the interior door handle once to unlock the door.
interior lock switch. The yellow indicator on the interior
2 Pull the interior door handle again to open the door.
lock switch illuminates.
If a mislock is caused by non-driver door, tailgate or bonnet, Speed Lock
press the interior lock switch. The yellow indicator on the All the doors will be locked automatically when the road
interior lock switch illuminates. speed exceeds 10 mph (15 km/h). 4
Automatic Unlock
When the vehicle power system is switched to the OFF
position, all the doors will be unlocked automatically.
157
STARTING & DRIVING
Tailgate The tailgate can be opened by using the following 2
If the tailgate can not be closed due to methods:
the type of cargo loaded, be sure to close 1 When the vehicle is unlocked or the matched key
all windows during driving, select the face appears within 1m range around the tailgate, directly
distribution mode of the air condition, and open the tailgate by turning over the emblem on the
set the blower to maximum speed, so as to tailgate (Figure A).
decrease any fumes entering the vehicle.
2 When START/STOP Switch in the OFF position, press
the release button on the remote key (Figure B) for
Tailgate Open Mode
more than 2 seconds to open the tailgate.
Emergency Tailgate Opening

The emergency tailgate release access is located in the
centre of the tailgate trim.
Fold down the rear seat to gain access, remove the
blanking plug, and rotate the emergency open knob
counterclockwise to open the tailgate from inside.
A B
158
STARTING & DRIVING
159
STARTING & DRIVING
Starting and Stopping the Power If the switch has not been operated and there are no
System indicators illuminated, the power system is OFF. The power
seats and electric door mirrors remain operational.
START STOP Switch Yellow Light (ACC)
Pressing the START STOP button without the footbrake
being applied whilst the vehicle power system is OFF will
place the system in the ACC state, this will illuminate the
yellow indicator in the switch button. The ACC position
S TA R T allows operation of certain ancillaries such as power
S TO P
windows.
Green Light (ON/READY)
• Whilst in the ACC state, pressing the START STOP
button without the footbrake being applied will place
the system in the ON state, the green indicator will
illuminate. This will allow the remaining electrical
The keyless START STOP switch is located in the fascia systems to operate.
to the left of the steering column, it is a push button style • Pressing the START STOP button with P selected
switch. To operate the switch the smart key must be inside and the footbrake applied will place the vehicle in
the vehicle. the READY state, the green indicator will illuminate
The operational status displays are as follows: and the word READY will appear in instrument panel
information display. This indicates that all electrical
Indicator Off (OFF)
160
STARTING & DRIVING
systems will operate and the vehicle is ready to be READY Mode
driven.
Setting the power system into READY mode:
Note: Whilst in the OFF state, if the driver exits
the vehicle leaving the smart key inside, after the 1 Ensure all unnecessary electrical loads are switched off.
second operation of re-opening the driver's door, the 2 Ensure the parking brake is applied.
instrument pack message centre will display a warning
3 Ensure P or N is selected (If the shift control knob
message to indicate that the key is still in the car.
is in any other position the power system cannot be
Note: To remove the electronic shift control knob from switched to the ON/READY state)
P the vehicle must be in an ON/READY state and the 4 Press brake pedal. 4
footbrake applied.
5 Press the START/STOP Switch (do not hold the button
If your car is subject to strong radio signals the keyless in, release immediately)
entry and start systems may suffer from interference and
not function correctly. Please see the ‘Alternative Starting’
procedure.
161
STARTING & DRIVING
IMPORTANT Alternative Starting Procedure
• If the vehicle will not enter a READY state, please
check for any warning indicators or messages displayed
in the instrument pack message centre. In extremely
low temperatures please allow 5 minutes between
power up attempts, if after 3 attempts the power
state cannot be set to READY please consult an MG
Authorised Repairer or breakdown service.
• Do not leave the power system in an ACC or
ON/READY state for long periods of time, excessive
use of electrical equipment may lead to to a discharged
battery.
• The vehicle is fitted with an anti-theft system.
Independently sourced keys may not allow vehicle
entry and system power up. Any new keys will require
programming using the manufacturers software.
If the vehicle is located in an area where there are strong
• Your car is fitted with complex electronic control
radio signals causing interference or the smart key battery
systems, please ensure that all other radio
condition is low, please use the following steps to attempt
transmission or electromagnetic devices are kept away
to start the car:
from the smart key and centre console cubby areas.
1 Place the smart key centrally in the centre console cup
They may cause interference and operational issues.
holder cubby box with the buttons facing upward - as
Please see the 'Alternative Starting' procedure.
shown in the illustration.
162
STARTING & DRIVING
2 Ensure P or N is selected, press the brake pedal and 3 Press START/STOP Switch to shut down the power
then press START/STOP Switch to power the vehicle. system.
If the vehicle power system cannot be changed after the
Note: Please observe the park brake warning light
car has left the area of strong radio interference or had
and message displayed in the instrument pack
the smart key battery replaced please consult an MG
message centre confirming that the parking brake
is applied before exiting the vehicle.
IMPORTANT
The Alternative Starting Procedure should only be

required if the smart key battery is very low or flat. 4
Once the vehicle has been removed from the area of
excessive radio interference the keyless entry and Start
Stop systems should return to normal.
Switching the Power System OFF

Setting the power system to OFF:
1 After bringing the car to a halt, ALWAYS maintain
brake pedal application.
2 Using the electronic shift control knob select (P), this
will automatically apply the parking brake - please
check that the parking brake is applied.
163
STARTING & DRIVING
Pedestrian Alert Control System
In order to improve the safety, your car is fitted with a

Pedestrian Alert System. When the vehicle is travelling at
a low speed, the system controls a speaker that sounds to
remind pedestrians in the vicinity of your presence.
Strategies of sounding warnings

The speaker sounds when all of the following conditions
are met:
1 The vehicle is READY;
2 The pedestrian alert system is fault free;
3 During acceleration, the vehicle speed is less than
19mph (30km/h); during deceleration, the vehicle
speed is less than or equal to 12mph (20km/h).
164
STARTING & DRIVING
Economical and Environmental Driving Economic Driving
The way in which you drive your car has a significant
Running-in
bearing on the life span of the car and battery.
The brakes and tyres need time to 'bed-in' and adjust to
the demands of everyday motoring. During the first 900 Drive Smoothly
miles, please avoid heavy braking where possible.
Anticipating obstructions and slowing down well in
advance, avoids the need for unnecessary acceleration and
harsh braking. A smooth driving style not only improves
battery/distance performance, but can reduce the amount
of wear on the brakes and tyres.
4
Avoid Driving at Maximum Speed
Power consumption and noise levels rise significantly at
higher speeds.
Driving Foreseeingly
Avoid roads with traffic congestion or traffic jams. Foresee
road congestion as early as possible , keep enough distance
from the car in front during driving, and slow down in time.
Avoid lengthy and heavy brake pedal applications when they
are not necessary, these will cause the brakes to overheat
and cause premature brake wear.
165
STARTING & DRIVING
Use of Electrical Equipment Driving in Special Environment
Use of electrical equipment will reduce the power available Driving in Rain or Snow
from the battery. Whilst it is essential to maintain
a comfortable interior environment, excessive use of Emergency braking, accelerating and steering
systems such as A/C will increase power consumption and on slippery roads will reduce the vehicle's
reduce the vehicle range. handling performance and grip.
• When raining, the windows may fog, reducing visibility

(Use the Air-conditioning demist function).
• Grip will be reduced, so please drive carefully.
• Reduce speed when it rains. Avoid aquaplaning (the
effect of a film of water between the tyres and the road)
affecting steering and braking performance.
Driving through Water
Avoid driving through floods after heavy rain, which may
lead to serious damage to the vehicle.
166
STARTING & DRIVING
Check and Service
Check Tyre Pressures Regularly
Under-inflated tyres increase the rolling resistance of the
car which, in turn, increases power consumption. Over or
under-inflated tyres wear out more rapidly and also have a
detrimental effect on the car’s handling characteristics.
Do not Carry Unnecessary Loads

The additional weight of unnecessary loads wastes power, 4
especially in stop/start conditions where the car is
frequently required to set off from stationary.
Maintain Correct Four-Wheel Alignment

Maintain the correct wheel alignment. Avoid collisions
with the kerb and reduce speed on uneven road surfaces.
Out of specification wheel alignment will not only lead to
excessive tyre wear, but also increases the load and power
consumption.
167
STARTING & DRIVING
Charging and Discharging After charging completion, switch off the
Requirements charger (where necessary), disconnect the
cable from the vehicle, fit the waterproof
Under normal circumstances it is strongly
blanking plugs, close the charging point door.
recommended that you use a slow charging
If necessary you can then disconnect the
method, avoid constant or regular use of
cable from the charger (where applicable).
rapid chargers.
Whilst charging the car on rainy days, where
Prior to using any charging equipment please
possible, please avoid connecting the charger
inspect the sockets, plugs and cables for any
during torrential rain or storms. If excessive
damage. DO NOT use any equipment that
water is evident around the charging plugs
shows signs of misuse or damage.
please use a suitable cloth to dry the area as
It is recommended that the charging cable best possible before removing the waterproof
be connected to the charging device before blanking plugs and connecting the charging
connecting to the vehicle and charging cables.
commences.
DO NOT touch the charging connector or
DO NOT attempt to switch the vehicle power charging plug when your hand is wet.
system to READY during charging.
DO NOT stand in water or snow when
connecting or disconnecting the charging
cable.
168
STARTING & DRIVING
DO NOT attempt to charge when the Always hold the charging connector handle
charging connector and plug are wet. or plug when connecting or removing the
charging cable, if you pull the cable itself
Always keep the charging connector and (without using the handle), the internal wires
charging plug in clean and in a dry condition. may disconnect or get damaged. This may
Be sure to keep the charging cable in lead to electric shock or fire.
a condition where there is no water or
High voltage charging or discharging
moisture.
equipment can cause interference with
Only use the correct charger for charging the electronic medical devices. When
electric vehicle. Using any other charger or using medical electrical devices such as
4
connector configuration may cause failure. pacemakers, please consult your doctor
about whether charging or discharging
Take care not to drop the charging connector. your electric vehicle will impact the
This could result in damage. operation of the device. In some instances,
electromagnetic waves that are generated
STOP charging or discharging immediately if from the charger can seriously impact
you find anything abnormal, such as sparks, medical electric device operation.
burning or smoke.
NEVER use a high powered jet wash directly
on the charger door or to clean around the
charge point.
169
STARTING & DRIVING
Charging Your Vehicle at Home NEVER allow water or fluids to enter or contaminate your
Whilst your MG has been supplied with a home charging charger or vehicle charging sockets.
kit, it is essential that you check with a qualified electrician NEVER use damaged charging points, equipment or
that the infrastructure of your property will support the sockets.
charging equipment. Please seek qualified advice that
STOP charging immediately if you see anything unusual,
your current electrical supply and circuits will support the
smell something burning or see sparks.
requirements of the charging equipment.
ALWAYS follow the operating instructions supplied with
Installed Charging Points your charging equipment.
Various companies will supply and install charging points Note: The charging point and power supply
to your property, MG insist that only qualified reputable infrastructure must be installed and serviced by
suppliers and installers are used - failure to have the correct suitable qualified personnel from an approved
equipment installed by a qualified professional may result in installation company using only the materials
overloaded circuits and fire. recommended by them.
Home Charging Guide

ONLY use certified approved equipment.
ONLY use qualified suppliers and installers.
When the battery is fully charged, disconnect the cable plug
from the vehicle socket - if it is necessary to interrupt the
charging of the vehicle, isolate the power supply first，
then disconnect the vehicle plug.
170
STARTING & DRIVING
Charging and Medical Condition Awareness Charging Port
High voltage charging equipment can create The charging port is located behind the charging port door
areas of strong electromagnetic interference, mounted in the front bumper. It is incorporated into the
this may cause operational issues with master locking system.
electronic medical devices. To open the door, ensure the vehicle is unlocked, press
the charging port door and release - the door will open to
When using medical electrical devices such as pacemakers
open the waterproof plug covers.
or cardioverter defibrillators (ICD's), please consult your
doctor about whether charging your electric vehicle will an Open the plug covers to reveal the combined charging port.
impact on the operation of the device. In some instances, 4
electromagnetic waves that are generated from the charger
can seriously impact medical electric device operation.
Note: There are no cautions issued about medical
devices when the car is not charging. It is perfectly safe
for individuals fitted with pacemakers or cardioverter
defibrillators to drive or ride in the vehicle.
1 2
171
STARTING & DRIVING
1 Slow and Fast Charge Port - 7 Pin - Type 2 Plug Charging Port Electronic Lock
2 Rapid Charge Port - 7 Pin and 2 Pin - CCS Type Plug In order to prevent the charging connector and cable being
disconnected inadvertently during charging, the charging
The upper plug covers the 7 pin slow/fast charging socket
socket features an electronic locking mechanism.
(1). The lower plug covers the rapid charging socket (2).
The electronic lock is activated as soon as the vehicle
Note: In order to use the rapid charger socket, both
begins charging, and remains in a locked state until the
waterproof plug covers will require removal.
charging is finished or interrupted.
After charging, refit the waterproof plug covers, close the
Whilst the charging cable is connected DO NOT attempt
charging port door, push the door fully home until the latch
to remove the plug.
locates.
ALWAYS ensure that any excess water is removed from Manually Releasing the Charging Port Lock in
the port area before connecting any charging device. Emergency Situations
The vehicle features an emergency release device for the
charging port lock.
To access the manual release, raise the bonnet and locate
the release cable on the O/S of the radiator cowling
assembly - see picture.
172
STARTING & DRIVING
Electric Charging Identifier Label *
Identifier Label on Slow Charging Kit
C
Pull the release cable handle, remove the connector plug
whilst maintaining tension on the cable this will release the 1
locking device.
1 AC charging identifier label
Note: Users can purchase a slow charging kit from an
MG Authorized Repairer.
173
STARTING & DRIVING
Identifier Labels on Charging Port cable. After checking that the alphabetic characters of
the charging identifier symbols match, proceed the next
charging step.
Note: Risk of failure, fire or injury etc. when using
a charging connector with unmatched identifier
symbols.
C K Electric charging identifier label symbol table
Supply Type of Voltage
Configuration Identifier
Type Accessory range
Vehicle
connector
1 2
AC 7P
and vehicle
≤480V C
inlet
1 AC charging identifier label Vehicle
2 DC charging identifier label connector
DC 7P+2P
and vehicle
50V–500V K
Precautions for AC or DC charging inlet
After opening the charging port door, check the charging
identifier symbol on the plug cover. Check the charging
connector identifier symbol on the AC or DC charger
174
STARTING & DRIVING
Rapid Charging pack may display less than 100% power. If you have a
Note: Please read any equipment operating long journey planned, it is recommended that you use
instructions carefully prior to using the rapid charging a slow charging point to charge the vehicle so as not
station. Each type of charger may use different to affect your journey (Battery Pack Type 1).
instructions.
Note: The cable of the charging plug should be shorter

than 30 m.
If you have any doubts, please seek professional assistance.
4
Rapid Charging Safety Precautions
• Before connecting the rapid charger, switch the vehicle
power system OFF and wait 10 seconds.
Note: If at any time during the charging process you
should want to check the state of charge, please switch
the vehicle power system to the ON position. The high
voltage battery state of charge will be displayed in the
message centre in the instrument pack.
Note: Considering the safety and service life of the

high voltage battery, when using a rapid charging
station to charge the vehicle the battery will not
become fully charged, and therefore the instrument
175
STARTING & DRIVING
Slow Charging AC Charging Points
Note: Carrying out a full slow charge is the only way IMPORTANT
for the high voltage battery to reach the optimal
Please ensure that only charge points that meet IEC
equilibrium state (equalisation charge).
61851 and IEC 62196 are used to connect to your
High voltage battery chargers are available with various vehicle.
power outputs. Chargers with outputs of up to 3 kW
are generally considered as slow chargers, 7 - 22 kW are Using an AC charging device:
considered fast chargers and rapid chargers are available in 1 Ensure the vehicle power system is OFF and all doors
AC or DC outputs. Generally the AC chargers are rated are closed.
at 43kW and the DC chargers at 50kW plus. 2 Open the charging port door, remove the waterproof
Charging times are dependent on charger output. plug cover from the 7 pin charging plug connector.
To carry out an equalisation slow charge, it is 3 Plug the cable from the charger point into the vehicle.
recommended that the charger output does not exceed Lock the vehicle.
7kW. 4 On completion of the charge， shut off the power,
unlock the vehicle and disconnect the plug from the
vehicle.
5 Ensure the charge socket is free from debris, fit the
waterproof plug cover. Close the charging point door.
176
STARTING & DRIVING
the vehicle power system to the ON position. The high Residential Charging
During the charging operation the vehicle power system
must be OFF. Carry out the following procedure to charge
the vehicle:
1 Ensure the vehicle power system is OFF and all doors
are closed.
2 Open the charging port door, remove the waterproof
plug cover from the 7 pin charging plug connector.
Ensure the surroundings are clean, dry and free from 4
debris.
3 Connect the 7 pin charging plug to the socket on the
vehicle.
4 Connect the charging device plug to the domestic
electricity supply. Lock the vehicle.
5 On completion of the charge, shut off the power,
unlock the vehicle, disconnect the charging cable from
the vehicle, and then the domestic plug.
6 Ensure the charge socket is free from debris, fit the
waterproof plug cover. Close the charging point door.
177
STARTING & DRIVING
the vehicle power system to the ON position. The high
178
STARTING & DRIVING
Charging Information
At the beginning of the charging process, the following information will be displayed within the instrument pack message
centre.
1 2
1 Charging status
Char ging 2 Charging time
Remai ning time :
3 hour 20 minute s
3 High voltage battery pack status
4 Driving range 4
231 mls 76%
4 3
Note: The information displayed on the instrument pack may be different based on vehicle configuration.
179
STARTING & DRIVING
Equalisation Charging Charging Times
Equalisation charging means that after a normal charging Charging times of the high voltage battery can vary
process the battery management system will enter a mode depending upon numerous factors, these include: current
where it will attempt to equalise the charge of every capacity, charging mode, ambient temperature and device
battery cell. type/power.
If an equalisation charge has not been carried out for some Rapid Charging Time
time, the message centre in the instrument pack will display
'Please Slow-charge the Vehicle'. Please refer to 'Slow Rapid chargers will vary in power output, on average it
Charging' in the 'Starting and Driving' section. will take approximately 40 - 60 minutes to charge the high
voltage battery up to 80% (80% displayed in IPK) using an
On average it takes at least 11.5 hours (battery pack type average rapid charger.
1) or 8.5 hours (battery pack type 2) to complete a charge
that includes the equalisation charge. Note: Ambient temperatures have an effect on
charging times. It may take longer to complete a
Note: Ambient temperatures have an effect on charge when the ambient temperatures are low or
charging times. It may take longer to complete a high.
charge when the ambient temperatures are low.
Slow Charging Time
On average it takes approximately 10.5 hours (battery pack
type 1) or 8 hours (battery pack type 2) to charge the high
voltage battery from low battery warning to 100% (charge
quantity can be checked using the instrument pack).
180
STARTING & DRIVING
• At low temperatures the charging time will be extended.
• If an equalisation charge has not been conducted for a
long time the required charge time will be extended.
• An equalisation charge must be carried out prior to
using the car after a long period of storage or non use.
In these cases the charging time will be extended.
Note: The slow charging notes above relate to using
an AC charging device. Use of the slow charging
device using a domestic power supply can increase the
charging times by up to 3 times. 4
181
STARTING & DRIVING
Indicative Charging Times for Battery Pack Type 1
Note: These times are only a guide.
From alarm status (the high voltage battery low warning displayed in the instrument pack message
Rapid charging
centre) to 80%, it takes almost 40 minutes.
From alarm status (the high From alarm status (the high voltage
It takes approximately
voltage battery low warning battery low warning displayed in the
28 hours to complete
displayed in the instrument pack instrument pack message centre)
an equalisation charge
Residential message centre) to 100% (the high to 100% (the high voltage battery
for first use after the
electricity voltage battery state of charge state of charge displayed in the
vehicle has been parked
or stored for a long
message centre), it takes almost and equalisation, it takes almost 26
time.
Slow 25 hours. hours.
charging From alarm status (the high From alarm status (the high voltage
13.5 hours to complete
AC an equalisation charge
message centre) to 100% (the high to 100% (the high voltage battery
charging for first use after the
voltage battery state of charge state of charge displayed in the
station vehicle has been parked
or stored for a long
message centre), it takes almost and equalisation, it takes almost
time.
10.5 hours. 11.5 hours.
182
STARTING & DRIVING
Indicative Charging Times for Battery Pack Type 2
Note: These times are only a guide.
From alarm status (the high voltage battery low warning displayed in the instrument pack message
Rapid charging
centre) to 80%, it takes almost 40 minutes.
From alarm status (the high From alarm status (the high voltage
18 hours to complete
an equalisation charge
Residential message centre) to 100% (the to 100% (the high voltage battery
electricity high voltage battery state of state of charge displayed in the
for first use after 4
the vehicle has been
charge displayed in the instrument instrument pack message centre)
parked or stored for a
pack message centre), it takes and equalisation, it takes almost 17
long time.
Slow almost 16 hours. hours.
charging From alarm status (the high From alarm status (the high voltage
9 hours to complete
AC an equalisation charge
message centre) to 100% (the to 100% (the high voltage battery
charging for first use after
high voltage battery state of state of charge displayed in the
station the vehicle has been
charge displayed in the instrument instrument pack message centre)
parked or stored for a
pack message centre), it takes and equalisation, it takes almost 8.5
long time.
almost 8 hours. hours.
183
STARTING & DRIVING
Discharging remove the discharge gun using force, this will damage
the locking mechanism.
The vehicle is equipped with a discharge function, this
can covert the high voltage DC power in the high-voltage 4 The user is able to click the stop discharging button in
battery pack into domestic AC power. the entertainment display screen to stop the discharge,
or stop the discharge after the power is discharged to
This discharge function can be realized by using a discharge
the set cut-off value. At this time the electronic lock
kit.
will automatically be released and the discharge gun
Note: Users have the opportunity to purchase the can be removed.
discharge kit from an MG Authorised Repairer.
5 Make sure there is no debris or foreign matter in the
To use the discharge function, follow the instructions charging port, fit the charging port cover and close the
below: charging point door.
1 Unlock the vehicle and access the AC charging port
Note: After the vehicle starts discharging, if the
(the charging port is also the discharging port).
entertainment display goes off, the vehicle will still
2 Insert the discharge gun connector into the discharge maintain the discharging condition.
port socket.
Note: During discharge, the START/STOP switch can
3 Access the discharger management interface in the be placed in the “ON” position to check the current
entertainment display screen, ensure the cut-off power status and driving range of the high-voltage
power of discharge is set. After setting, click the battery pack via the instrument cluster.
start discharging button, the electronic lock will lock
the discharge gun in place and the vehicle will enter Note: During the discharge process, the user can still
the discharge state. At this time, do not attempt to set the discharge power cut-off point.
184
STARTING & DRIVING
Note: During discharge, the vehicle cannot be placed
in “READY” mode.
Note: Using the discharge function will reduce the

driving range of the vehicle.
IMPORTANT
• Before beginning the discharge operation, check the

condition of the discharge connector and gun.
• If it is necessary to use the discharge function on wet 4
days, please pay particular attention in protecting the
discharge port area and discharge gun from water,
rain or snow.
• In cases of abnormal phenomena such as peculiar
smells, smoke emission or overheating etc during
the discharge process, the electrical circuit MUST
be disconnected immediately and the discharge
operation stopped.
185
STARTING & DRIVING
Electric Drive Transmission When the vehicle is in motion, it is prohibited
to switch from D gear to R gear or P gear, it
Instructions may cause serious damage to the electric drive
transmission or cause an accident.
The following information is very important. Please read
carefully before use:
• The electric drive transmission consists of a high voltage
unit. DO NOT touch any drive components unless you
have the correct training and qualifications.
• Before setting the vehicle power system to ON, close
the door, make sure the vehicle is in P or N gear, apply
the brake pedal and activate the EPB.
• When the vehicle power system is READY, the brake
and EPB are still maintained, shift to the required gear.
• Switch off the EPB and maintain brake pedal application
until you are ready to manoeuvre. On a flat road,
once the brake pedal is released, the vehicle may
automatically start moving slowly without applying the
accelerator pedal.
The shift control knob is in the intermediate steady state
Gear Shift Control position, and there are two unsteady positions clockwise
and counterclockwise, that is, the shift control knob will
DO NOT press the shift control knob whilst return to the intermediate steady state position once
driving . released.
186
STARTING & DRIVING
• P Park If the brake pedal is released, the driver seat belt
is unfastened and the driver door is open, P will
When the shift control knob is in this position, the
automatically be selected and engaged.
electronic parking brake has been applied. Only select
this gear when the vehicle is stationary. • R Reverse
Select this gear only when the vehicle is stationary and
Note: The electronic parking brake system must be you wish to drive backwards.
released via the EPB switch. See “Electronic Parking
Brake (EPB)” under the “Brake System” section. Apply the brake pedal, turn the shift control knob
counterclockwise to the end and release. The spring
Note: If the electronic parking system fails to loaded shift control knob will return to a central 4
activate, the vehicle will enable the parking position and the vehicle will enter Reverse.
function of the electric drive transmission, the P • N Neutral
gear indicator on the shift control knob will flash.
Select this gear when the vehicle is stationary (for
Operating the shift control knob to select any other
example, waiting for traffic lights).
gear will exit Park.
When in Park, apply the brake pedal, turn the shift
The shift control knob can be pressed to select and
control knob clockwise or counterclockwise to the
engage P.
first non-steady state position and release. The spring
If the START/STOP Switch is operated to power the loaded shift control knob will return to a central
vehicle OFF, P will automatically be selected and position and the vehicle will enter Neutral.
engaged.
In Reverse, turn the shift control knob clockwise to
the first non-steady state position and release. The
187
STARTING & DRIVING
spring loaded shift control knob will return to a central return to a central position and the vehicle will enter
position and the vehicle will enter Neutral. Drive.
Whilst D is selected, turn the shift control knob For safety reasons ALWAYS apply the brake pedal
counterclockwise to the first non-steady state position when shifting between R and D positions.
and release. The spring loaded shift control knob will
return to a central position and the vehicle will enter
Neutral.
• D Drive
This is used for normal driving.
Whilst in Park, apply the brake pedal, turn the shift
control knob clockwise to the end and release. The
spring loaded shift control knob will return to a central
position and the vehicle will enter Drive.
In R or N, turn the shift control knob clockwise to the
end and release. The spring loaded shift control knob
will return to a central position and the vehicle will enter
Drive.
When the vehicle is stationary and has remained in
Neutral for more than 2 seconds. Please apply the brake
pedal, turn the shift control knob clockwise to the end
and release. The spring loaded shift control knob will
188
STARTING & DRIVING
Driving on Hills Driving Mode
In cases where a short stop on a hill is Please avoid switching between Driving
required, such as a traffic jam, DO NOT Modes while driving. This may divert the
frequently apply the accelerator pedal to driver's attention away from road conditions
prevent a “ roll back”. This could cause the and cause an accident.
electric drive transmission to overheat or
In each of the different driving modes, the control system
even system damage.
uses different control strategies for output control.
Hill Start
4
In cases of a hill start, the start assist function of the
electronic parking brake (EPB) can be used to prevent the
vehicle from rolling backwards. For details on this function,
please refer to “Electronic Parking Brake (EPB)” in the
“Brake System” section.
Models equipped with Hill Hold Control can use this
function to assist hill starts. For details on the hill hold
control system, please refer to “Hill Hold Control” in
“Brake System” section.
Note: The aid of these functions cannot defy the
laws of physics. DO NOT drive the vehicle beyond its
physical limitations. Loss of control will still occur.
189
STARTING & DRIVING
The driver can select three driving modes by operating the Every time the vehicle power system is cycled and the
MODE switch: system set to READY, the driving mode defaults to the
1 ECO Mode NORMAL Mode.
The vehicle is in the state of low energy consumption, Selecting different driving modes will also automatically
which is used for energy-saving driving. select the settings of other systems such as electronic
steering and A/C - please see the chart below:
2 NORMAL Mode
Driving Power Steering A/C
The vehicle is balanced for daily driving.
Mode Mode Mode Mode
3 SPORT Mode
ECO Eco Urban Eco
Sport Mode concentrates on providing more power to
enhance the performance. NORMAL Normal Normal Normal
Constant use of Sport Mode will increase energy SPORT Sport Dynamic Sport
consumption.
Note: While ECO Mode is selected, the A/C will
It is recommended to choose the Sport Mode when operate in a low energy consumption state to provide
driving on special road conditions such as mountain an increase in vehicle power.
roads .
When the driving mode is switched, the message centre
will display: ECO , NORMAL, SPORT.
190
STARTING & DRIVING
Energy Regeneration
Deceleration caused by energy regeneration
is NOT a substitute for braking safely. The
driver must ALWAYS be prepared to make
braking manoeuvres to maintain safe driving.
When the vehicle is in a braking, over-run or coasting

state, the energy regeneration function is activated, and
the motor converts part of the kinetic energy of the vehicle
into electric energy, which is then stored in the high voltage 4
battery pack.
Energy cannot be regenerated or is limited under some
conditions, such as:
• N gear is selected (During driving do not coast in N The driver can select three energy regeneration levels by
gear) ; operating the KERS switch :
• During torque intervention (SCS or traction control 1 Heavy
operation) ; Heavy Level: Maximum energy is regenerated, the
• High voltage battery pack is fully charged; vehicle exhibits shorter coasting distances and a strong
• High voltage battery pack temperature is too high or sensation of over-run drag or motor braking. The
too low. message centre displays 3 .
2 Moderate
191
STARTING & DRIVING
Moderate Level: Moderate energy regenerated. The Energy Management
message centre displays 2 .
3 Light
Light Level: Minimum energy is regenerated, the
vehicle exhibits longer coasting distances and no
significant sensation of over-run drag or motor
braking. The message centre displays 1 .
Every time the vehicle power system is cycled and the
system is set to READY, the energy regeneration level
defaults to the Heavy Level.
Note: It is recommended to choose Light or Moderate
levels on surfaces that have low adhesion levels (e.g.
icy roads).
The driver can operate the BATTERY switch backward

to display the energy management interface in the
infotainment system.
192
STARTING & DRIVING
Protection Mode If the electric drive transmission has cooled down for a
long time (about 20 minutes) and the warning message has
When parking the vehicle, please ensure the
not disappeared, please park the vehicle safely and seek an
vehicle is parked safely and that all traffic
MG Authorised Repairer immediately. Otherwise it may
by-laws are observed.
seriously damage the electric drive transmission.
Motor Overheating Protection for the Electric IMPORTANT
Drive Transmission When the motor of the electric drive transmission

is under overheating protection, in order to avoid
The electric drive transmission may become very hot in
a high-temperature environment with frequent starting,
damage to the motor, the power of the vehicle will 4
be limited (the message centre will display “Power
frequent rapid acceleration and deceleration, long-term
Limited, Limiting Speed”, and warning indicator
continuous steep climbing, and overload of the electric
will illuminate). After decelerating, the warnings will
drive transmission. In order to prevent damage to the
disappear when the motor temperature returns to
motor, the system will perform an overheating protection
normal.
function, the warning message “Motor Overheating”
displays.
Motor Fault of Electric Drive Transmission
In this case, park your vehicle safely or, while keeping a low
load, continue to drive your vehicle at a constant speed to If a fault or failure is detected in the motor or the power
cool the motor. Only when the motor temperature has electronic box of electric drive transmission, the warning
decreased, and the warning message disappears, can the message “Motor Fault, Consult Handbook” will display
vehicle be driven normally. simultaneously. Please seek an MG Authorised Repairer
immediately.
193
STARTING & DRIVING
Parking System Fault of Electric Drive In some cases, the electric drive transmission will enter
Transmission Limp Mode and will only function at certain speeds, please
seek an MG Authorised Repairer immediately.
If a fault or failure is detected in the electrical park motor
control unit, the warning indicator will illuminate, Severe Functional Malfunction
and the warning message “Parking System Fault, Consult In some cases, when a fault or severe failure is detected
Handbook” will display simultaneously. After a few in the electric drive transmission, the warning indicator
seconds, the warning message will disappear but the
will illuminate in red, and the warning message
warning indicator will remain on, please seek an MG “Vehicle Control System Fault, Please Stop Safely!” will
Authorised Repairer immediately. display simultaneously. After a few seconds, the warning
Electric Drive Transmission Fault message will disappear but the warning indicator will
remain on. To protect the electric drive transmission, the
In some cases, when a fault or failure is detected, the power system will isolate the power transmission, and the
warning indicator will illuminate in yellow or red vehicle will not be able to be driven, please seek an MG
according to different faults, and the warning message Authorised Repairer immediately.
“Vehicle Control System Fault, Please ask Serving Station
for Help!” or “Vehicle Control System Fault, Please drive In some cases, when a fault or severe failure is detected
carefully!” will display simultaneously. After a few seconds, in the gear shift system, the message centre will display
the warning message will disappear but the warning “EP”. For safety reasons, if the vehicle speed is below
a preset speed, the power system will isolate the power
indicator will remain on.
transmission, and the vehicle will not be able to be driven,
please seek an MG Authorised Repairer immediately.
194
STARTING & DRIVING
Brake System safe to do so, please pull over and allow the electric
vacuum pump to cool down for a while. Please power
The free stroke of brake pedal is 0–30 mm. the vehicle again, to return to normal.
Driving through water or heavy rain may adversely affect • If the prompt message "Vacuum System Fault" is
braking efficiency. The SCS (Stability Control System) displayed in the instrument pack, bring the car to a halt
includes a Brake Disc Wiping function which is activated as quickly as traffic conditions safely allow and contact
when the windscreen wipers are used. However, always an MG Authorised Repairer as soon as possible. At
keep a safe distance from other vehicles and intermittently this time, the brake system may be unable to provide
apply the brake pedal in conditions where the wipers are sufficient braking force, DO NOT drive the vehicle.
not used. • The efficiency of the brake servo booster can be 4
affected by numerous conditions, such as change of
The brake system is servo assisted, always be aware of the
atmospheric pressure due to altitude differences. These
followings during the operation:
conditions could result in extra force being required to
• The servo assistance function is reliant upon vacuum, operate the brake pedal to stop the car.
this is only produced whilst the vehicle power system is
ON or READY. NEVER allow the car to coast when the Electronic Brake Force Distribution (EBD)
vehicle power system is OFF.
Your car is equipped with Electronic Brake Force
• Vacuum to support the system is provided by an
Distribution, which, in order to maintain braking efficiency,
electric vacuum pump. DO NOT continually pump the
distributes braking forces between front and rear wheels,
brake pedal, this may affect the vacuum pump efficiency,
under all load conditions.
the brake system may be unable to provide sufficient
brake assist and the vehicle speed will be limited. If
this situation does occur or is unavoidable, when it is
195
STARTING & DRIVING
Electronic Brake Assistance (EBA) ABS can prevent the wheels from locking while braking,
thereby enabling the driver to retain steering control of
Your car is equipped with Electronic Brake Assistance,
the car.
which reacts to the speed at which the brake pedal is
applied. If, in an emergency situation the brakes are applied Under normal braking conditions, ABS will not be
faster than the limits set within the system, then full ABS activated. However, once the braking force exceeds the
application is applied to bring the car to a stop in the available adhesion between the tyres and the road surface,
shortest possible distance. thereby causing the wheels to lock, ABS will automatically
come into operation. This will be recognisable by a rapid
Anti-lock Brake System (ABS) pulsation felt through the brake pedal.
When travelling at high speed or there is a If an emergency situation occurs, the driver should apply
danger of aquaplaning, i.e. where a layer full braking effort to activate ABS even when the road
of water prevents adequate contact between surface is slippery.
the tyres and the road surface, ABS cannot
Note: On soft surfaces such as powdery snow, sand
overcome the physical limitations of stopping
or gravel, vehicles equipped with ABS may have a
the car in a short distance. In these cases, it
braking distance greater than those without ABS. This
is the responsibility of the driver to maintain
is because the natural action of locked wheels on soft
a safe distance from other vehicles.
surfaces is to build up a wedge of material in front of
(or to the side of, if steering) the tyre contact patch.
DO NOT pump the brake pedal at any time,
This effect assists the car to stop when braking or to
this will interrupt the operation of ABS and
change direction when steering.
may increase the braking distance.
196
STARTING & DRIVING
IMPORTANT • The driver's door is closed and the driver seat belt is
fastened.
ABS can not reliably make up for the driver's
• The vehicle is stopped on a slope for more than 2
misoperation or lack of experience.
seconds.
• SCS is active and fault free.
Hill Hold Control (HHC) • EPB is fault free and released.
HHC has limitations when subject to adverse • Power system is READY.
conditions such as wet or icy surfaces and • D or R gear is selected.
steep slopes. • Sufficient brake pedal application force has been applied.
4
DO NOT exit the vehicle with only HHC Note: HHC is available in both forward and backward
applied, it may lead to a serious accident directions when pulling away on uphill slopes.
when HHC releases.
Firm application of the brake pedal when

stopping is required by HHC to generate
sufficient brake pressure to maintain hold.
HHC assists the driver by 'holding' the vehicle during hill

starts. If the driver releases the brake pedal, the HHC will
hold the vehicle stationary for a short time.
The following conditions must be fulfilled to activate HHC:
197
STARTING & DRIVING
Hill Descent Control (HDC) the driver to drive on acute downhill surfaces at low
The HDC system is only an auxiliary speed.
function. It has limitations when subject to Note: When HDC system is working, the brake system
adverse conditions such as wet or icy surfaces will produce slight vibration or working noise, which is
and steep slopes. a normal phenomenon.
Even when HDC system is switched on, the Note: During the operation of the HDC system, please
driver must always pay close attention to do not move the shift control knob to the "N" position.
the driving state of the vehicle, and take Such operation may deactivate the HDC function.
active control when necessary. In certain
cases, HDC may be suspended or switched HDC System On/Off
off temporarily.
When the START/STOP Switch is switched to ON/READY,
During some driving conditions on downhill the HDC system defaults to off. Use the switch within the
surfaces (e.g. driving down a slope at infotainment system to turn the HDC system on/off.
high speed or small slope, etc.), HDC is
The HDC system has four states:
inoperative, the driver must maintain control
1 Standby: Press the HDC switch to set the system into
of the vehicle at all times and use brake
standby mode, the green HDC indicator lamp in the
applications to ensure safety.
instrument pack will illuminate.
The HDC system is an auxiliary function specially designed 2 Operation whilst in Standby mode: When the vehicle
for driving on acute downhill gradients. The system drives onto a steep slope at a low speed and the driver
reduces the speed by applying brake force, thus assisting does not press the brake and accelerator pedal, the
198
STARTING & DRIVING
system will automatically enter the operating state. In result in a 'kickback' sensation through the pedal. This
this case, the HDC indicator lamp in the instrument is a normal phenomenon.
pack flashes green, this may be accompanied by the
working noise of the brake system. The HDC system Auto Hold
will attempt to control the vehicle's descent down the The Auto Hold function cannot guarantee
steep slope smoothly. the stability of the vehicle when starting off
3 Temporary Deactivation: By pressing the accelerator or braking on hills especially on slippery or
pedal or if the brake pedal is pressed beyond a certain icy surfaces.
limit whilst in operating mode, the HDC system will
temporarily suspend operation.
When Auto Hold stops the vehicle, for 4
reasons such as power system shutdown,
4 Off: Press the HDC switch again to switch the system releasing the seat belt or pressing the Auto
off, the green HDC indicator lamp in the instrument Hold switch, the electronic parking brake is
pack will extinguish. applied. It cannot be guaranteed that the
vehicle will be stabilised in all cases. For
Note: If the vehicle undergoes sharp steering
example, the rear wheels are on a slippery
manoeuvres on certain gradients, the HDC system
road surface, or the vehicle incline is too
may change from the standby state to the operating
great. Please make sure that the vehicle is
state.
safely stabilised prior to exiting.
Note: During HDC system operation, the brake system
The driver should pay full attention and
will automatically pressurise and maintain pressure.
observe the surroundings even if the vehicle
Operation of the brake pedal during this phase may
is equipped with Auto Hold system.
199
STARTING & DRIVING
Auto Hold cannot guarantee the electronic Standby state. The Auto Hold switch indicator lamp
parking brake operation in all cases where illuminates.
the power system is shut down. Please ensure
2 Parking:
the electronic parking brake is applied and
the vehicle is stabilised prior to exiting the With the brake pedal firmly pressed and the vehicle
vehicle. completely stopped, the Auto Hold function will
switch from Standby state to Parking state. In this
The Auto Hold function should be switched
state the green indicator on the instrument pack
off during the use of automatic car washes,
illuminates.
otherwise the electronic parking brake may
suddenly apply and cause vehicle damage. When the Auto Hold is in the Parking state, engaging
forward or reverse gear and pressing the accelerator
If the vehicle is required to stop frequently for a length of pedal will automatically release the Auto Hold
time (such as traffic lights, traffic queues or stop/start), and function.
the power system is running, the Auto Hold system assists
3 Off:
in stabilising the vehicle, enabling you to remove your foot
from the brake pedal when the vehicle is stationary and the Press the Auto Hold switch again to turn the function
Auto Hold active. off.
Auto Hold has 3 main states:
1 Standby:
With the driver's seat belt fastened, the driver’s door
closed and the power system running, press the
Auto Hold switch to switch the function from Off to
200
STARTING & DRIVING
Note: It is recommended to turn off the Auto Hold
function when reversing into the garage.
Active Rollover Protection (ARP)

The ARP system is a driver aid to assist the stability of the
vehicle under extreme conditions. It is not a guarantee that
the car will not roll over.
In cases where the vehicle has a high centre of mass, rapid
or excessive dual direction lane changing may create a 4
roll condition. ARP may use the brake system to apply
certain brakes to try and correct the condition and assist
in preventing rollover.
Note: During ARP application the steering
In some circumstances such as releasing the seat belt,
characteristics of the vehicle may be noticeably
switching off the power system or remaining static for
different from normal.
a length of time, it will result in exiting the Auto Hold
Parking state. At this time the electronic parking brake Emergency Braking Hazard Warning Lights
will be applied. Control (HAZ)
Note: The parking brake will NOT be applied when When the vehicle is driving at high speed, if the driver
operating the switch to turn the Auto Hold off with makes an emergency braking manoeuvre, the brake lamps
the brake pedal pressed. will automatically flash to alert the drivers behind.
201
STARTING & DRIVING
Note: If the hazard warning lamps are being operated • A vehicle collision where seat belts or airbags are
manually, this suspends the HAZ function. deployed;
When the emergency braking manoeuvre is exited (no • The vehicle speed is less than 37.5mph (60km/h);
severe deceleration detected) then the function will be • The steering wheel has not been turned in excess of
switched off after a few seconds. 180°;
• SCS is fault free.
Note: As the car speed drops to below 6mph (10km/h)
After a collision or the MCB function is triggered, if the
and the brake lamps no longer flash, the hazard
driver strongly applies the accelerator pedal, the system
warning lamps will illuminate automatically. Short
will not trigger or exit the braking state.
press the hazard warning lamp switch or increase
your speed to above 12mph (20km/h) for 5 seconds to Note: The MCB function cannot decelerate the
switch off the hazard warning lamps. vehicle in all cases of collision, because the collision
process may cause some parts to malfunction or fail
Multi-Collision Brake System (MCB) and affect the normal operation of the function.
The MCB function will automatically apply the brake to
reduce the vehicle speed and improve the vehicle stability
after a collision. It is designed to reduce the risk of a
secondary collision caused by the uncontrolled movement
of the vehicle after a collision.
The MCB will be activated when the following conditions
are all met at the same time:
202
STARTING & DRIVING
Stability Control System and Traction system will reduce motor power in order to regulate
Control System wheel rotation until traction is regained.
Stability Control System (SCS) Switching On/Off

SCS is designed to assist the driver in control of driving SCS and TCS are automatically switched to standby when
direction. the power system placed in ON/READY position, they
When SCS detects that the vehicle is not moving in the can be switched off by using the switch located within the
intended direction, it will intervene by applying brake infotainment system when the power system is in READY
force to selected wheels or through the power system mode.
management system to prevent sliding and assist in bringing Note: Disabling SCS and TCS will not affect the
4
the car back to the right direction. operation of ABS. Always disable SCS and TCS when
driving with snow chains fitted.
Traction Control System (TCS)
The purpose of TCS is to aid traction, thereby helping the
driver to maintain control of the car in situations where
one or both of the driving wheels are spinning (for example,
if one wheel is on ice and the other on tarmac).
TCS monitors the driving speed of each wheel individually.
If spin is detected on one wheel, the system automatically
brakes that wheel, transferring torque to the opposite,
non-spinning wheel. If both wheels are spinning, the
203
STARTING & DRIVING
Electronic Parking Brake (EPB) Applying EPB
In the event of EPB malfunction where EPB When the vehicle is parked safely, selecting P on the shift
release is not possible, please consult an MG control knob will automatically apply the EPB. If the EPB
Authorised Repairer in order to carry out an cannot be activated automatically, please activate the EPB
emergency manual release of the parking manually as follows before leaving the vehicle or parking.
brake. • Pull the EPB switch upward until the indicator in the EPB
switch illuminates.
• If the indicator in the EPB switch and the indicator
in the instrument pack illuminate, the EPB is applied.
Note: An audible motor noise may be heard when
applying or releasing EPB.
IMPORTANT
• DO NOT leave the vehicle before the indicator in

EPB switch illuminates and the gear indicator displays
P, the vehicle may not be safely parked due to EPB
failure and slip.
• In the event of a flat battery or power failure it is
not possible to apply or release the EPB. If using
'jump leads' to temporarily supply power please see
'Emergency Starting' in the Emergency Information.
204
STARTING & DRIVING
Releasing EPB is pressed in order to pull away, the EPB will automatically
release.
If the vehicle is stably parked on a flat road or slight
incline/decline, the vehicle power system is READY, press Emergency Braking Function
the brake pedal to allow the shift control system to switch
from P to N, D or R, the EPB will automatically released. Inappropriate use of EPB can lead to
accidents and injuries. Do not apply the EPB
If on a steep slope, switching from the P position will not
for vehicle braking unless in emergency.
automatically release the EPB. In this case, manually release
the EPB as follows or apply the Start Assist function of the During emergency braking using the EPB, DO
EPB to release the EPB. NOT switch off the START/STOP Switch, this 4
• Ensure the vehicle power system is set to the could result in serious injury.
ON/READY position, press the brake pedal, and press
the EPB switch. In the event of normal brake failure, emergency braking
• If the indicator in the EPB switch and the indicator using the EPB can be initiated by pulling and holding the
in the instrument pack are extinguished, the EPB is EPB switch upward.
released. • Pull the EPB switch upward and hold to realise the
Start Assist emergency braking. In the process of emergency
braking, an audible warning will sound at the same time.
The EPB can predict the driver's intention and
• To cancel the emergency braking process, release the
automatically release.
EPB switch.
If the driver's seat belt is fastened, the power system is
READY, D or R gear is selected and the accelerator pedal
205
STARTING & DRIVING
Adaptive Cruise Control System accelerate or gently apply the brakes of the car to maintain
the set following distance.
The adaptive cruise control system is
designed as a comfort system enabling the Note: The adaptive cruise control system is designed
driver to maintain a constant speed or for highways and roads in good condition. It is
distance from the car in front. It provides recommended not to be used on urban roads and
assistance to the driver, it DOES NOT replace mountain roads.
any of the drivers responsibilities. When
using the adaptive cruise control system, Adaptive Cruise Control System Activation
it is important that the driver maintains
After following the vehicle ahead to a stop,
concentration at ALL times and is prepared
the driver must observe any local traffic laws
to take action. Otherwise, accidents or
and ensure that there are no obstacles or
personal injuries may occur.
other traffic participants, such as pedestrians,
directly in front of the vehicle before allowing
The adaptive cruise control system can automatically
it to pull away and begin to follow the vehicle
switch between constant speed cruise and car following
ahead again.
cruise depending on whether it can detect a vehicle directly
ahead. Constant speed cruise controls the vehicle within Whilst using the car following cruise function
a certain speed range. Car following cruise operates by it is strongly recommended that the driver
setting the distance between the vehicle and the vehicles does not touch the accelerator pedal. Any
directly ahead. activation of the accelerator will not allow
When activated if the adaptive cruise control system the system to automatically apply the brakes
detects a vehicle in the same lane directly ahead it may should this be necessary.
206
STARTING & DRIVING
DO NOT exit the vehicle when the adaptive 1
cruise control system car following cruise
function has stopped the car, or is keeping 8
0
the car stationary. Before exiting the car
the shift control knob should be in the Park
4 5
position and the START/STOP Switch in the
0
OFF position.
7 3 6 9 2
If the adaptive cruise control system has
already stopped the vehicle, and the adaptive 4
cruise control function is disabled, turned off
or cancelled, the vehicle will no longer stay
still, it may move forward or slip backward.
When the vehicle is stopped and kept still by
the adaptive cruise control system, be sure to 1 Speed Limit Increase/Accelerate
be ready to apply the brakes manually. 2 Speed Limit Decrease/Decelerate
When driving on a bend, the adaptive cruise 3 Cancel

control may actively reduce the vehicle speed 4 Standby
to maintain vehicle stability and safety.
5 Resume
6 Set
7 OFF
207
STARTING & DRIVING
8 Increase Distance （30 km/h）, then the target speed of the system is
set at 20mph （30 km/h）. If the speed of the vehicle
9 Decrease Distance
ahead is greater than the cruise target speed of your
The adaptive cruise control system is operated with a lever vehicle, your vehicle will maintain the target speed to
switch, which is located, at the left side of the steering conduct constant speed cruise. If the speed of the
wheel underneath the indicator/lighting stalk switch. vehicle ahead is lower than the cruise target speed of
1 With the vehicle START/STOP Switch in the your vehicle, it will enter the car-following cruise. An
ON/READY position, if the adaptive cruise lever image of your car and the car ahead is displayed in
switch is in the ‘OFF’ position (7), then the adaptive the instrument pack message centre. In this mode the
cruise control system is switched OFF. actual speed may be less than the set target speed.
2 Move the adaptive cruise lever switch to the ‘ON' Whilst in the car following cruise mode, you can
position (4), the adaptive cruise system status indicator follow the vehicle ahead to a stop. If the parking time
on the instrument pack illuminates yellow, the adaptive is less than a preset time period, your vehicle may
cruise control system is in the Standby mode. automatically pull away to follow the vehicle ahead,
or you need re-activate the adaptive cruise control
3 The system will automatically detect the speed and system using the method displayed.
position of the vehicle ahead, if your vehicle speed
is above 3mph （5 km/h）, after pressing the 'Set' Note: Manual deactivation of either the Traction
button (6) at the end of the adaptive cruise stalk lever, Control System (TCS) or Stability Control System
the indicator on the instrument pack will turn green, (SCS) will inhibit the operation of the adaptive cruise
and the adaptive cruise control system enters the control system.
Activated mode, its target speed is the actual speed
at activation; if your vehicle speed is less than 20mph
208
STARTING & DRIVING
Adaptive Cruise Target Speed Adjustment or downward (2) once, the target speed will change
5mph （5 km/h）, press and hold the lever upward or
When the adaptive cruise control system is activated:
downward and the speed will increase or decrease in
1 Use the accelerator pedal to reach the desired speed,
1mph （1 km/h） increments, release the lever when
short press the 'Set' button (6) on the end of the
the desired speed reading is displayed.
adaptive cruise switch lever, release the control button
and accelerator pedal. The vehicle will cruise at the Note: If the vehicle ahead continually makes hard
desired speed. acceleration or deceleration manoeuvres the adaptive
cruise control may not be able accurately maintain the
2 Move the lever switch upward (1) and hold, the target
required distance between vehicles. It is important
speed will increase until the desired set speed appears
that the driver always concentrates and pay attention 4
in the instrument pack, then release the switch. When
to the current vehicle position and situation in case
it is confirmed that there is no vehicle in front of your
they need to make a braking or avoidance manoeuvre.
vehicle or the vehicle ahead exceeds the preselected
following distance, the speed will be increased to the
Adaptive Cruise Target Following Distance
set speed.
Adjustment
3 Move the lever switch downward (2) and hold, the
When the adaptive cruise control system is activated,
target speed will decrease until the desired set speed
rotate the switch on the end of the lever upward (8)
appears in the instrument pack, then release the
or downward (9) to adjust the following distance, you
switch, the vehicle speed will decrease to the set
are able to toggle between 3 distance settings which are
speed.
displayed in the message centre in the instrument pack.
4 When using the lever to adjust the target speed, briefly
Always select an appropriate following distance that is
operate the adaptive cruise lever switch upward (1)
relative to the current speed of your vehicle and the
209
STARTING & DRIVING
vehicle you are following, the greater the speed, the • Follow the vehicle ahead to a stop and the stop time
further the distance. ALWAYS consider current traffic, exceeds a certain period of time.
road and weather conditions when making your selection. • The camera or radar view is blocked, the surrounding
environment triggers the preset safe exit mechanism of
Adaptive Cruise Pause/Standby the sensors, or the system fails.
When the adaptive cruise control system is activated, move Note: If following the vehicle ahead to a stop with
the lever switch to the 'Cancel' position (3), and the system the adaptive cruise control system enabled, if any of
will exit to the Standby mode. the following conditions occur whilst the vehicle is in a
stopped state, the EPB will automatically be applied:
Automatic Deactivation of Adaptive Cruise • The driver unfastens his/her seat belt.
In the following situations, the adaptive cruise control • The driver door is opened.
system may be automatically deactivated, this transfers full • The stationary time exceeds the preset time period.
control of the vehicle to the driver.
• Move the lever switch to ‘OFF' position (7).
Adaptive Cruise Override
• Press the brake pedal whilst the vehicle is in motion. If the driver has cause to use the accelerator pedal
• Move the rotary gear knob to either R or N position. when the adaptive cruise control system is activated, the
• The driver unfastens his/her seat belt. vehicle will remain in Cruise mode while the vehicle speed
increases. When the accelerator pedal is released, the
• Press and hold the accelerator pedal beyond a preset
adaptive cruise control system will resume to operate at
time period.
previously set cruise speed.
• Open any door, bonnet or tailgate.
• Pull the EPB switch up to apply the parking brake.
210
STARTING & DRIVING
Adaptive Cruise Resume • A vehicle suddenly cuts into the lane in front.
If the adaptive cruise control system has reverted to, or • Encounters a vehicle driving at a low speed.
been switched to, the Standby mode it can be reactivated • Encounters a vehicle with loaded items protruding from
by moving the lever switch to the ‘Resume' position (5). the body profile of the vehicle.
The target cruise speed will automatically be set to the • Encounters a vehicle with a higher chassis (e.g., a truck).
target speed before exiting the adaptive cruise control • Encounters pedestrians, non-motor vehicles or animals.
system. • The vehicle is driving on an uneven road or a complex
traffic road section.
Clear Speed Memory • The vehicle makes a sharp turn.
4
If the lever switch is moved to the ‘OFF' position (7) or • Enters and leaves a tunnel or drives in the tunnel.
the vehicle START/STOP Switch is switched to the OFF • Drives in the shade of mottled trees.
position, the system may clear the adaptive cruise control • Excessive weight being carried in the boot space or
set speed in the memory. cargo area causing the front of the car to point upwards.
Adaptive Cruise Control System Impairment Special Driving Environments

and Ineffectiveness
The adaptive cruise control system has it's limitations.
• Encounters a vehicle or object which is stationary or
Listed below are some conditions that may be beyond the
traversing the lanes.
safe operating limits. The driver should maintain control
• Approaching the vehicle ahead too fast, and the system of the vehicle and must remain alert at all times. They
cannot apply sufficient braking force. should pay special attention to the traffic conditions and
• The vehicle ahead is an oncoming vehicle, or makes an surroundings, select the appropriate speed and be ready
emergency braking manoeuvre. to take any required actions.
211
STARTING & DRIVING
be unable to detect the vehicle ahead, even if it is in the
same lane, it is possible the system may detect a vehicle in
another lane.
Note: Do not use the adaptive cruise control system
on entrance/exit ramps or sharp bends.
If the vehicle ahead changes lanes, but does not drive into
the lane completely, the adaptive cruise control system may
be unable to detect the vehicle.
If the vehicle ahead changes lanes, but does not exit the
When turning at an intersection or following a vehicle into, lane completely, the adaptive cruise control system may
or out of a curve, the adaptive cruise control system may
212
STARTING & DRIVING
determine that the vehicle ahead has exited the lane and
accelerate to any preset speed.
When driving on uneven roads that may include steep

climbs or dips please DO NOT use the adaptive cruise When driving behind a vehicle that is only partially
control system. overlapping your vehicle, ‘A' in the graphic, the adaptive
cruise control system may be unable to detect anything.
Note: Please DO NOT use the adaptive cruise control
system in the following situations:
• Driving in bad weather conditions.
213
STARTING & DRIVING
• When the ambient light is insufficient, the light is
too bright, or the forward lighting of the vehicle is
poor.
• Driving on rough or poor road surfaces.
• Driving through roadworks or construction sites.
• Driving on low friction roads.
214
STARTING & DRIVING
Parking Aid System Rear Parking Aid
The ultrasonic sensors in the rear bumper monitor the area
Ultrasonic Sensor Parking Aid
behind the vehicle to search for obstacles. If any obstacle
The purpose of the parking aid is to assist the is detected, the system will calculate its distance from the
driver in reversing! The sensors may not be rear of the vehicle and communicates the message to the
able to detect obstacles of certain type, e.g. driver by sounding warning chimes.
narrow posts or small objects no more than
a few inches wide, small objects close to the Parking Aid in Operation
ground, objects above the tailgate and some The rear parking aid is enabled automatically when
objects with non-reflective surfaces. reverse is selected, it is switched off as soon as reverse
4
is disengaged. A short beep is given by the parking aid
Keep the sensors free from dirt, ice and snow. within 1 second after selecting reverse to indicate that the
If deposits build up on the surface of the system is operating normally.
sensors, their performance may be impaired.
When washing the car, avoid aiming high The entertainment system screen will display a silhouette
pressure water jets directly at the sensors image of the car showing the object distance values for the
from close range. sensor.
Note: If a longer, higher pitched sound is emitted for 3
seconds when reverse is selected this indicates a fault
in the system. In this case seek assistance from your
MG Authorised Repairer.
215
STARTING & DRIVING
With the parking aid enabled, when obstacles are detected, • Once the obstruction is within 30cm range of the rear
the system will give sounds in different frequencies (there bumper, the beeps will merge into a continuous warning.
might be blind areas).
1 .2 m
30cm
• If there is an obstacle within 1.2m range from the rear

sensors, the system starts to emit a beeping sound. As
the vehicle moves closer to the obstacle, the beeps are
transmitted more rapidly.
216
STARTING & DRIVING
360 Around View System The 360 around view system can be enabled using the
following methods:
The purpose of the 360 around view system
is to assist the driver during parking, The • Selecting Reverse gear.
cameras have a limited field of vision and • Operating the 360 button.
cannot detect obstructions outside the field • Using the 'Setting' interface to select low speed
of vision. switching of corner lights/indicators, this will
automatically open the 360 around view system when
Although the entertainment display can the indicators are used at low speeds and exit when
provide images around the vehicle, please the indicators are cancelled.
still pay attention to the current actual road In the 360 around view system display interface, select 4
conditions for your driving safety. the settings icon to enable personal settings for system
functions.
Please ensure that the exterior rearview
Note: When the shift lever is placed in a forward gear
mirrors are unfolded when using the 360
position, the 360 around view system is inhibited at
around view system.
speeds above or equal to 10mph (15km/h).
With the 360 around view system activated, the
entertainment display will display the 360 degree
panoramic image of the vehicle to facilitate the observation
of the surrounding environment in order to assist with
safer driving. Buttons on the entertainment display can be
touched to view the images from different angles around
the vehicle.
217
STARTING & DRIVING
Rear Driver Assistance System * The rear driver assistance function is only an
aide, it is NOT a substitute for the attention
System Overview of the driver. The driver must always remain
The rear driver assistance sensors may in control, observe the surroundings and drive
misidentify some surroundings, such as safely.
roadside buildings or guardrails and provide
The rear driver assist system may not provide
a false alarm.
adequate warning of very fast approaching
The effective recognition capabilities of the vehicles or operate correctly on tight curves
rear sensors can be limited by objects such of 500m radius or less.
as roadside buildings, guardrails, changes in
pitch angle of the car due to heavy loading, The rear driver assist system will not operate
road conditions such as bends or bumps or correctly whilst towing a trailer or caravan.
weather conditions such as snow and ice etc.
Any of the above may trigger a false alarm. The correct operation of the rear sensors will
be compromised if they are misaligned due to
The system has limitations and may not be accident damage. This may cause the system
able to warn of vehicles approaching at high to automatically shutdown.
speeds.
To ensure that the radar sensors work
correctly, the rear bumper should be kept
free of snow and ice and must not be covered.
218
STARTING & DRIVING
Use of non recommended materials or
paint on rear bumper repairs may have a
detrimental effect on the operation of the
rear sensors. Please only use recommended
materials.
The rear driver assistance system includes blind spot

detection (BSD), lane change assist (LCA), and rear cross
traffic alert (RCTA) functions.
The rear driver assistance modules are mounted at the 4
rear of the vehicle on each side, they can assist in detecting
vehicles behind or to the side of your vehicle.
The warning lamps to support this system are located
within the LH and RH door mirror glasses, they will Note: The radar requires calibration on new vehicles
illuminate or flash to warn of an approaching object or car or for vehicles of where a rear detecting radar
to assist you in manoeuvring the car safely. sensor has been replaced. The rear detection radar
sensors possess an automatic calibration function to
compensate for installation error within a certain
range. When the vehicle is running, the radar will
automatically enter the calibration state. During the
calibration process, the system will provide limited
functions, and the alarm may be inaccurate. Upon
219
STARTING & DRIVING
completion of the calibration, the system will resume System Functions
all functions. Note: The detection area, collision time threshold
value and vehicle speed provided in the system
Switching the System Functions On/Off function description are just for your reference.
The rear driver assist system function and sub system
switches can be accessed via the infotainment screen. Blind Spot Detection (BSD)
Select ON/OFF to activate/deactivate the system. When the vehicle is driving forward, the system will
monitor the motor vehicles located in the blind zones of
the left and right exterior mirrors. When the conditions
for activating the blind spot detection function are met, the
warning lamps in the corresponding mirror will illuminate.
Subsequent operation of the relevant indicator will cause
the warning lamp in the mirror to flash to remind the
driver of an approaching vehicle.
220
STARTING & DRIVING
and 7m behind the rear of the vehicle, and 3.5m to the
side of the vehicle are the system detection areas.
Note: The warning lamps will not illuminate whilst
you are overtaking another vehicle and your speed is
greater than that of the vehicle you are passing, even
though it is in the blind zone.
The conditions for activating the blind spot detection

function include:
1 No faults are present in the system.
2 Blind spot detection (BSD) function is enabled.
3 The vehicle speed is above 10mph (15km/h).
4 There are motor vehicles in the blind zone of the
vehicle. The left and right areas, which are 1m ahead
221
STARTING & DRIVING
Lane Change Assist (LCA) The conditions for activating the lane change assist function
include:
When the vehicle is driving forward, the system will
monitor the motor vehicles approaching rapidly in the 1 No faults are present in the system.
adjacent lanes. When the indicators are activated, and the 2 Lane change assist (LCA) function is enabled.
conditions for activating the lane change assist function
3 The vehicle speed is above 10mph (15km/h).
are met, the system will flash the warning lamp within the
respective mirror to warn the driver of an approaching 4 The speed of the approaching vehicle is higher than the
vehicle. This aims to help avoid collisions when changing speed of your vehicle.
lanes. 5 The approaching vehicle enters the detection area of
the lane change assistance, the monitored areas are
7m - 70m behind your vehicle and 3.5m to the side of
your vehicle.
6 The approaching vehicle is likely to have a collision with
your vehicle within 3.5 seconds.
222
STARTING & DRIVING
Rear Cross Traffic Alert (RCTA) The conditions for activating the rear cross traffic alert
function include:
When the vehicle is reversing, the system will monitor
vehicles approaching from the left and right rear. When 1 No faults are present in the system.
the conditions for activating RCTA function are met, the 2 Rear cross traffic alert (RCTA) function is enabled.
warning lamps in the mirrors on the corresponding side
3 The vehicle is in Reverse gear.
will illuminate, simultaneously a warning triangle icon for
the corresponding side will be displayed in the infotainment 4 The vehicle speed is less than 6mph (10km/h).
screen to alert the driver to the situation. 5 The speed of the vehicle being monitored is above
6mph (10km/h). 4
6 The motor vehicle drives across the system detection
area. The areas monitored to the left and right of the
vehicle are 7m behind the rear of the vehicle, and 30m
from the side.
7 The approaching vehicle is likely to have a collision with
your vehicle within 3 seconds.
223
STARTING & DRIVING
Tyre Pressure Monitoring System ‘Instruments and Controls’ section. TPMS can remind you
(TPMS) of low tyre pressure, but it can not replace normal tyre
maintenance. For tyre maintenance, please refer to ‘Tyres’
TPMS can not replace routine maintenance in ‘Maintenance’ chapter.
and checks of tyre condition and pressures.
Using equipment that transmits on If the TPMS malfunction indicator lamp

frequencies similar to that of the TPMS illuminates, and the warning message “XX Tyre Pressure
may interfere with the operation of the Low” is displayed, it is advised that you please stop the
Tyre Pressure Monitoring System, this may car as soon as possible, check the tyre pressure and
illuminate a warning or register a temporary inflate the tyre to correct pressure value. Driving with
fault. under-inflated tyres may overheat and cause tyre fault.
Over or under-inflated tyres wear out more rapidly
Note: TPMS only warns of low tyre pressures, it does and also have a detrimental effect on the car’s handling
not re-inflate the tyre. characteristics. Under-inflated tyres increase the rolling
resistance of the car which, in turn, increases power
TPMS uses pressure sensors built into tyre valves to consumption. Always check/adjust tyre pressures when
continuously monitor pressure and transmit data to the they are cold.
ECU inside the vehicle using RF signals. If it deduces
that the pressure of that tyre has fallen below the Note: After changing the tyre position or replacing a
predefined limit of the system, the warning light in the TPMS sensor and receiver, the vehicle needs to run at
instrument pack will illuminate (always yellow). For a speed of 25mph for about 10 minutes to correctly
more information, please refer to ‘Instrument Pack’ in indicate the tyre pressure value at the corresponding
position.
224
STARTING & DRIVING
Driving Assist System Note: The calibration of front view camera requires
professional knowledge and tools. If calibration is
Under certain conditions the driving assist system can required, please seek an MG Authorised Repairer.
detect the road and environmental information ahead of
the vehicle by utilising a front view camera and a front Obstruction of the front view camera
detection radar. This information is used to relay warning
On occasion the front view camera view may become
messages or provide assistance to help the driver in
obstructed by foreign objects or stains on the glass.
controlling the vehicle in a safer and more reliable manner.
In these cases a prompt message will appear in the
The front view camera is located in the interior rearview
information centre. Please wipe or clean immediately.
mirror base cover, the front detection radar is located at 4
the lower middle of the front bumper. In the following situations, the detection
Note: DO NOT operate any infotainment switches performance of front view camera will be
whilst driving. If you wish to make any settings
changes, please pull over when it is safe and legal to affected:
do so. • Driving in poor weather conditions where visibility is
reduced due to thick fog, heavy rain, snow, dust or sand
Description of Front View Camera storm etc.
• Affected by light, for example low light levels at night,
Calibration of front view camera poor auxiliary lighting, excessive backlighting in the
The front view camera will require re-calibration after any view, light from oncoming vehicles, abrupt change
of the following operations: of brightness with a quick bright/dark jump (tunnel
• Removal and refitting of the front view camera. entrance/exit), driving on surfaces with strong reflective
• Replacement of the windscreen.
225
STARTING & DRIVING
properties (road surface covered with water or snow), Note: If the front detection radar is subject to strong
tunnels, inside a building etc. vibration or slight impact, the mounting position of
• The front view camera view is partially or fully blocked the front detection radar needs to be checked and
by obstacles, e.g. dust, foreign objects, oil pollution, re-calibrated as necessary.
mud, snow, excessive water (rain), frost or water spray
Note: The calibration of front detection radar requires
from the road on the windscreen.
professional knowledge and tools. If calibration is
• The windscreen viewing area is damaged.
required, please seek an MG Authorised Repairer.
• Not calibrated after removing/refitting the front view
camera or the windscreen. Front radar performance will be effected in the
• The front view camera is not secured in place.
following situations:
Description of Front Detection Radar
• When the front detection radar is covered by mud,
Calibration of front detection radar snow, excessive water (rain) or water spray from the
road.
The front detection radar re-calibration is required after
any of the following: • When the radar or surrounding areas are covered by
objects such as labels or auxiliary lighting installation.
• The front detection radar mis-alignment failure, for
example the position of the front detection radar has • When the front detection radar is subject to strong
changed. vibration or slight impact.
• Remove/refit the front detection radar or radar bracket. • Some targets may affect and weaken the detection
capability of the front detection radar, such as road
• Remove/refit the front anti-collision beam.
barriers, fences and tunnel entrances.
• The four-wheel alignment parameters have changed.
226
STARTING & DRIVING
• When the front detection radar is affected by the Speed Assist System
environment, such as strong electromagnetic field
The intelligent speed assist system is an
interference or due to the target itself.
auxiliary function. It may display an
• Strong reflected radar signals (such as: in multi-storey incorrect speed limit value or no speed limit
car parks, tunnels, sprinkler spray systems or water jets value in the instrument pack due to various
etc). Experiencing any of these could cause the function factors. As a result, the vehicle speed is
of the front detection radar to be effected. not restricted within the correct range. The
Note: Any snow that gathers on the front radar may driver still needs to observe the speed limit
be removed using a soft brush, and any ice should be of the road traffic, and speeding is strictly
removed using a propriety deicing spray. prohibited. 4
Note: Avoid any collision or contact with the front
The front view camera cannot recognise
radar module, this may cause misalignment.
speed limit signs painted on the road surface.
The driver MUST observe these speed limits
and adjust the their speed accordingly.
The speed assist system settings are available via the

infotainment system. Enter the MG Pilot interface to
locate the speed assistance system option and switch on
or off the overspeed alarm function. When the adaptive
cruise control system is OFF, you are able to choose from
227
STARTING & DRIVING
the intelligent speed limit function, manual speed limit speed within the permitted maximum speed limit. A
function or not enabled. visual warning will be utilised when over speed. Please
refer to the section “Speed settings of manual speed
5/ limit”.
1 Overspeed alarm: The vehicle detects a speed limit Speed assistance system setting
sign (as shown above) at the roadside with the front The operating interface for the speed assistance system
view camera. The speed limit sign identified will be is located in the infotainment display. Enter the MG Pilot
displayed in the instrument pack. When the vehicle interface to locate the speed assistance system option to
speed exceeds the speed limit by a preset amount, a find the setting interface for the speed assistance system:
visual warning in the instrument pack will flash. 1 Touch the corresponding button on the infotainment
2 Intelligent speed limit: The vehicle detects a speed display to turn the overspeed alarm function On/Off.
limit sign (as shown above) at the roadside with the 2 Touch the corresponding button on the infotainment
front view camera. The speed limit sign identified will display to select the speed assist mode: intelligent
be displayed in the instrument pack. The system will speed limit, manual speed limit.
automatically intervene and maintain speed control to
keep the vehicle speed within the permitted maximum Speed settings of manual speed limit:
speed limit. A visual warning will be utilised when over
After the manual speed limit function is enabled, the speed
speed.
limit value can be set by using the adaptive cruise control
3 Manual speed limit: The driver sets the maximum lever as follows:
speed using the adaptive cruise control lever. The 1 Moving the control lever to adjust the speed limit.
system will actively intervene and keep the vehicle After the speed limit value is displayed in the
228
STARTING & DRIVING
instrument pack, press the SET button (3 in the 3 After the manual speed limit function is activated, the
figure below), the manual speed assist function will be driver can press the SET button (3 in the figure below)
activated. When pressing the SET button, if the actual on the adaptive cruise control lever to reinstate the
speed value is lower than the setting, the speed limit system to the standby state. Press the SET button
value displayed in the instrument pack will be defined again, the manual speed assist function will be resumed.
as the setting. If the actual speed value is higher
than the speed limit adjusted, the speed limit value 1
displayed in the instrument pack will be defined as
the current actual speed and rounded to the nearest
value of 5mph (62mph will be defined as 65mph). The 4
speed range is 20mph - 100mph. Moving the lever
up or down once will increase or decrease the speed
limit value by 5mph. Holding the lever up or down
3
will continuously change the speed limit value in units 2
of 5mph.
2 After the manual speed limit function is activated, the
system will actively intervene and keep the vehicle
speed within the target speed limit. If the current
actual speed exceeds the target speed limit value set
by the driver, the system will reduce the speed until it N N N
is below the target speed limit. When the overspeed alarm function or
intelligent speed limit function is enabled, the speed limit
229
STARTING & DRIVING
value indication illuminates. When the vehicle passes the illuminates yellow. When the function is activated by
first speed limit sign identified, the speed limit indication pressing the SET button on the adaptive cruise control
displays the real-time speed limit value. lever, the system indicator lamp illuminates green. If the
intelligent speed assist function detects a fault or failure,
Note: When the vehicle needs to change lane, make
the indicator lamp will flash yellow then extinguish. Please
a turn, or turn around at an intersection and the
try to restart this function. If this function cannot be
driver uses an indicator in advance and slows down,
turned on, please contact an MG Authorised Repairer.
the original speed limit value on the instrument pack
will be reset until a new speed limit sign is detected.
NNN
If the conditions are not met, the original speed limit When the front view camera detects a speed
value will be maintained and not be reset. The driver limit sign with a text message below, the warning lamp
MUST observe the speed limits and adjust their speed illuminates to remind the driver to read and act upon the
accordingly. message themselves. The camera cannot recognise the
text messages provided below the speed limit sign, such as
auxiliary lane, 100mls ahead, school section, 7:00-10:00.
When the national speed limit sign is identified
The camera will recognise the speed limit sign with text
and the speed limit information function or intelligent
messages as a normal speed limit sign. The driver is
speed assist function is enabled, the national speed limit
required to make correct judgement according to the text
indication illuminates. These two functions will work using
message.
60mph as the national speed limit.
When the manual speed limit function is

When the intelligent speed limit function is
enabled, the system indicator lamp in the instrument pack
enabled, the system indicator lamp in the instrument pack
illuminates yellow. When the function is activated by
230
STARTING & DRIVING
pressing the SET button on the adaptive cruise control instrument pack will change to yellow. Press the SET
lever, the system indicator lamp illuminates green. If the button again to resume the functions.
manual speed assist function detects a fault or failure, the
3 Move the adaptive cruise control lever to the “ON”
indicator lamp will flash yellow then extinguish. Please try
position to switch the speed limit function off.
to restart this function. If this function cannot be turned
on, please contact an MG Authorised Repairer. The overspeed alarm function and intelligent
NNN speed limit function may be impaired in the
mph
When the manual speed limit function is following situations:
enabled, the speed limit value indication illuminates. Move
the adaptive cruise control lever up and down to adjust
1 The detection performance of the front view camera 4
is affected.
the target speed limit value. The “NNN” will now show
the adjusted speed limit value. 2 The vehicle is driven at a high speed.
The driver can directly switch off, or temporarily suspend 3 The speed limit signs are obscured along the road, for
the intelligent speed limit function or manual speed limit example: by trees, ice/frost, snow, dust, etc.
function by carrying out the following actions: 4 The speed limit signs are incorrectly placed or
1 To temporarily exceed the speed limit (overtaking damaged.
manoeuvre), press the accelerator pedal hard. The
5 There are multiple speed limit signs above the lane or
indicator lamp in the instrument pack illuminates
on the sides of the road. Currently, the front view
green, and the speed limit value flashes.
camera can only recognise the speed limit signs for the
2 Gently press the SET button on the end of the lane in which the vehicle is being driven.
adaptive cruise control lever, the indicator lamp in the
231
STARTING & DRIVING
6 Non standard speed limit signs or signs that contain Lane Assist System
additional information.
The lane assist system is an auxiliary system
7 The speed limit signs set up at a fork in the road, on a that provides assistance to the driver. It does
bend or on-ramp/off-ramp. NOT remove the responsibility of safe driving
8 During manoeuvres such as lane-changing. from the driver. When choosing to use the
lane assist system, the driver MUST always
IMPORTANT pay attention to the surroundings, hold the
• The camera may not correctly recognise speed limit steering wheel and be prepared to make
signs during poor lighting conditions, bad weather, manoeuvres at any time. Failure to maintain
non-standardized or sheltered speed limit signs overall control of the vehicle may result in
or the camera’s own restrictions which include an accident or personal injury.
the recognition of similar signs (e.g., recognise a
The lane assist system does not always
weight limit sign as a speed limit sign, or recognise a
recognise the lane lines and curbs.
minimum speed sign as the maximum speed sign).
Sometimes poor road surfaces, certain road
• Some drastic or rapid steering operations made by
structures or objects may be mistaken for
the driver may be judged as changing lane or turning
lane lines. When such situations occur,
around at an intersection by the system. This will
the lane assist system must be immediately
result in the identified speed limit signs being cleared.
turned off.
The lane assist system switch is located in the infotainment

display. Enter the corresponding interface for driving
232
STARTING & DRIVING
assistance to turn the system ON/OFF, and make mode • The function is switched ON,
selection. • Vehicle speed is above 37mph （60 km/h）,
• Lane line markings are clear and the system recognises
Alert
at least one lane line.
The system uses the front view camera to detect the lane When a wheel is about to cross the lane line or curb, or
lines ahead of the vehicle. The system will be activated has already crossed the line or curb, the system will provide
when the following detection conditions are met: assistance to the driver by attempting to keep the vehicle
• The function is switched ON, in between the lane lines by applying corrective steering
• Vehicle speed is above 37mph （60 km/h）, intervention and simultaneously displaying a prompt. If
• Lane line markings are clear and the system recognises the vehicle deviates from the lane lines too much ， the 4
at least one lane line. system will activate the alert function. The function will
When a wheel is about to cross the lane line, or has automatically exit when the vehicle speed drops below
already crossed the line, the system will provide warnings 33mph （55 km/h）.
to prompt the driver to take action and maintain the In the absence of a steering input from the driver for a
vehicle position between the lane lines. The function will certain period of time, the system will provide warnings.
automatically exit when the vehicle speed drops below
33mph （55 km/h）.
Emergency lane keeping

The system uses the front view camera to detect the lane
lines and curbs ahead of the vehicle. The system will be
activated when the following detection conditions are met:
233
STARTING & DRIVING
IMPORTANT • During system intervention the steering wheel is
operated (in the mode of emergency lane keeping).
• In cases where the number of lanes increase or lanes
• The lane line is too thin, damaged, or fuzzy.
merge, the driver MUST take full control of the
vehicle. • The curb is irregular or damaged.
• In areas where there are complex traffic conditions • The vehicle is being driven on a bend with a small
such as intersections or road junctions with curvature radius, the road is too narrow or too wide.
congestion, the driver MUST take full control of the • The vehicle has just entered a road section with lane
vehicle. lines or is driven on a road section without lane lines.
• The vehicle changes lanes or sways laterally too fast.
The lane assist system will be impaired or • The vehicle is not in D.
• The vehicle speed is below 33mph （55 km/h）, or too
ineffective in the following conditions: high.
• The hazard lamps are activated.
• The anti-lock brake system (ABS) and the dynamic
• The driver indicates in the direction of the lane line stability control system (SCS) are activated.
about to be crossed.
• Faults exist in the anti-lock brake system (ABS), dynamic
• The driver applies the accelerator rapidly, carries out stability control system (SCS), electric power steering
an emergency manoeuvre or makes a hard brake pedal system (EPS), etc.
application.
• The system detects that the driver has not moved the It is recommended to turn off the lane assist
steering wheel for a preset time period (in the mode of system in the following situations:
emergency lane keeping). • Driving in a sports style or manner.
• Driving in bad weather conditions.
234
STARTING & DRIVING
• Driving on rough or poor road surfaces. Traffic Jam Assist System
• Driving through roadworks or construction sites. The traffic jam assist system is an auxiliary
system that provides assistance to the driver.
It does NOT remove the responsibility of
safe driving from the driver. When choosing
to use the traffic jam assist system, due
to the limitations of system detection and
control, the driver must always be careful
and hold the steering wheel at all times.
The driver needs to correct or take over the 4
steering wheel control if necessary. Failure
to maintain overall control of the vehicle
may result in an accident or personal injury.
235
STARTING & DRIVING
• The adaptive cruise control system is activated.
1 • The traffic jam assist system is switched on via the
corresponding button in the infotainment system.
2 • The system detects lane lines on both sides of the
vehicle.
• The vehicle is in D.
If the lane lines ahead on both sides are clear, the system
can assist the vehicle in driving within the lane lines. When
driving at low speed, if there is a vehicle ahead and the lane
lines ahead on both sides aren't clear, the system also can
assist the vehicle in following the track of the vehicle ahead.
In the absence of a steering input from the driver for a
certain period of time, the system will provide warnings.
The traffic jam assist system switch is located in the
Note: The driver should adjust the vehicle speed and
infotainment display. Enter the corresponding interface for
the following distance according to the road visibility,
driving assistance to turn the system ON/OFF. Operating
weather and road conditions. The traffic jam assist
the adaptive cruise control level to “RESUME” twice will
system does not respond to pedestrians, animals,
switch the traffic jam assist system into the standby or
stationary vehicles and vehicles that drive across the
active state.
lane or oncoming vehicles in the same lane. If the
The traffic jam assist system works on the same basis as the traffic jam assist system cannot reduce the vehicle
adaptive cruise control system. The system will operate speed timely and effectively, the driver MUST apply
when the following conditions are met: the brakes. In congested conditions, should another
236
STARTING & DRIVING
vehicle cut into the lane being used by the vehicle • The vehicle has just entered a road section with lane
under traffic jam assist system control, the system lines or is being driven on a road section without lane
may not detect the vehicle in adequate time to make lines.
a braking manoeuvre. In this case the brakes should • The vehicle is not in D.
be applied by the driver. • The vehicle changes lanes or sways laterally too fast.
• The turning radius of the car using the traffic jam assist
The traffic jam assist system will be impaired or system to track in front is too small.
ineffective in the following conditions: • The anti-lock brake system (ABS) and the dynamic
• The hazard lamps are activated. stability control system (SCS) are activated.
• The driver indicates in the direction of the lane line • Faults exist in the anti-lock brake system (ABS), dynamic
4
about to be crossed. stability control system (SCS), electric power steering
• The driver applies the accelerator rapidly, carries out system (EPS), etc.
an emergency manoeuvre or makes a hard brake pedal It is recommended to turn off the traffic jam
application.
• The system detects that the driver has not moved the
assist system in the following situations:
steering wheel for a preset time period. • Driving in a sports style or manner.
• During system intervention, the steering wheel is being • Driving in bad weather conditions.
manipulated by the driver. • Driving on rough or poor road surfaces.
• The lane line is too thin, damaged, or fuzzy. • Driving through roadworks or construction sites.
• The vehicle is being driven on a bend with a small • Driving on steep, winding or slippery roads (such as
curvature radius, the road is too narrow or too wide. snow covered and icy roads, wet roads and roads
covered with water).
237
STARTING & DRIVING
• Driving on grass tracks or unpaved roads. Forward Collision System
IMPORTANT The driver remains responsible for the safety
of the entire driving process, even if the
• In cases where the number of lanes increase or
vehicle is equipped with a forward collision
lanes merge the driver MUST take full control of the
system. The driver MUST pay full attention
vehicle.
and drive carefully. As with all the driver
• In areas where there are complex traffic conditions assist systems, the forward collision system
such as intersections or road junctions with cannot prevent accidents or avoid collisions
congestion, the driver MUST take full control. in all situations. The driver MUST always
• The driver MUST be aware of the surroundings and remain in control to avoid accidents or
be able to assume full control of the vehicle when emergency situations.
using the traffic jam assist system to track the car in
front should the need arise. Emergency braking whilst under the control
of the forward collision system may cause
injuries to the passengers. Therefore, drive
carefully and all passengers MUST wear seat
belts at all times.
238
STARTING & DRIVING
Ensure the forward collision system or vehicle Emergency braking
power system is switched off when being
When the system detects that there is a risk of collision
towed. If the forward collision system is
between the vehicle and the vehicle directly in front of the
enabled when the vehicle is being towed,
vehicle, the brake system will automatically intervene to
adverse effects may affect the safety of your
decelerate the vehicle, so as to avoid collision accidents
vehicle, the towing vehicle and the people
or mitigate damage from collision accidents. If the vehicle
around.
is braked and stopped under the system control, it will
remain stationary for a short time. Full control of the
To avoid the occurrence of accidents, never
vehicle will then be returned to the driver.
specially test the functions of the forward 4
collision system. Pedestrian auto emergency braking
The forward collision system switch is located in the When the system detects that there is a risk of collision
infotainment display. Enter the corresponding interface for between the vehicle and the mobile pedestrian directly in
driving assistance to turn the system ON/OFF, and make front of the vehicle, the brake system will automatically
mode selection. intervene to decelerate the vehicle, so as to avoid collision
accidents or mitigate damage from collision accidents. If
Alert the vehicle is braked and stopped under the system control,
it will remain stationary for a short time. Full control of the
When the system detects that there is a risk of collision
vehicle will then be returned to the driver.
between the vehicle and the vehicle in front in the same
lane, warnings will be provided to prompt the driver to The system will only slow down the vehicle automatically
slow down in time and keep a relatively safe distance from if the following conditions are met:
the vehicle ahead.
239
STARTING & DRIVING
• The dynamic stability control system (SCS) and traction • The vehicle ahead is an abnormal vehicle (modified or
control system (TCS) are fault-free and ON. abnormal shape).
• The vehicle is in D or N. • The vehicle ahead is a vehicle with higher chassis.
• The airbags are not deployed. • The vehicle ahead is a large vehicle at close range (such
Note: In some cases, the driver may not have as tractor, trailer, towing vehicle, mud truck, sanitation
anticipated any braking intervention and does truck, sprinkler truck etc.).
not want to apply the brakes whilst the forward • The vehicle ahead is unusual transportation (such as a
collision system is braking heavily, the driver can horse, cart, carriages etc.).
temporarily cancel this operation by heavily pressing • The system detects the side of a vehicle.
the accelerator pedal after ensuring that it is safe to • The contour of the vehicle ahead is unclear (such as
do so. water being sprayed by the wheels of the front and
surrounding vehicles).
The operation of the forward collision system • The vehicle ahead does not have or has obscured tail
may be impaired or ineffective in the following lamps when driving at night or in a tunnel.
situations: • The tail lamps of the vehicle ahead are all LED strip lights
• The vehicle ahead approaches head-on, crosses the or other homemade coloured lamps.
intersection or jumps the queue rapidly in a short • The street lights are inconsistent or flickering when
distance. driving at night.
• The vehicle ahead does not follow the rules of driving • The pedestrian is not directly in front of the vehicle, or
and parking (such as drives on the lane lines). the pedestrian is not fully visible.
• The vehicle ahead is not in the same lane as your vehicle • The pedestrian is not standing upright, or it is a child
or the vehicle ahead is partially obscured. under a certain height.
240
STARTING & DRIVING
• There is a group of pedestrians in front of the vehicle
that is over-shadowed or in the dark.
• There are animals in front of the vehicle.
• Objects such as special-shaped ground obstacles (e.g.
roadblocks, isolation piles, isolation strips, large stones,
other scattered objects etc.) are detected in front of
the vehicle.
• Objects such as signs, guardrails, bridges, buildings or
other are detected in front of the vehicle.
• The vehicle is being driven on a hillside road, upper and 4
lower bridge section or tight bend.
• The vehicle is in R.
• The vehicle is in a state of braking or rapid acceleration.
241
STARTING & DRIVING
Load Carrying IMPORTANT
DO NOT exceed the gross vehicle weight Traffic regulations must be observed when loading cargo,
or the permitted front and rear axle loads. if the cargo extrudes the loadspace appropriate warning
Failure may result in vehicle damage or measures must be taken to warn other road users.
serious injury.
Internal Loading
Loadspace Loading DO NOT carry unsecured equipment, tools
Ensure that the rear seat backrests are or luggage that could move, causing personal
securely latched in the upright position when injury in the event of an accident, or
loads are carried in the load space behind the emergency braking or hard acceleration.
seats.
DO NOT obstruct the driver's or passenger's
When luggage is carried in the load space, always ensure vision with loads.
heavy items are placed as low and as far forward as possible,
so as to avoid the cargo shift in the event of an accident or Folding the rear seats can increase luggage space, refer
sudden stop. to “Rear Seats” described in the “Seats and Restraints”
section.
Drive carefully and avoid emergency braking or
manoeuvres. When cargo is loaded in the vehicle, place it at a position
as low as possible and ensure that it is tightly secured, so as
Driving with the tailgate open is very dangerous. If the
to avoid personal injury caused by cargo movement when
load being carried requires the tailgate to be open, please
traffic accidents or emergency braking occurs. If the cargo
ensure the cargo is suitably secured.
242
STARTING & DRIVING
has to be placed on a seat, then the seat must not be used Tow bars: Only genuine MG approved tow bars should
by an occupant during that time. be fitted to your vehicle. Only use the attachment method
specified by the vehicle manufacturer for securing the
General Towing Safety towing hitch. Contact your authorised MG dealer for
more information.
Your vehicle can tow a trailer if you carefully observe load
limits, use approved equipment, and follow the towing Safety chains: Safety chains must be used as a
guidelines. Always check load limits before towing. precautionary measure should the trailer become
unintentionally unhitched. Make sure the safety chain is
Towing loads in excess of the maximum towing weight
securely attached to both the trailer and the vehicle prior
can seriously affect vehicle handling and performance, and
to departure. 4
could damage your vehicles engine and drive-train.
Note: Exceeding any load limits advised by MG Motor
Altitude: Your engine delivers less power at higher
altitude. If you tow a trailer in a mountainous area you
is dangerous. Consult the recommended load limits
should reduce the combined vehicle and trailer weight by
and loading prior to any journey.
10% for every 1000 m of elevation.
Check the loading of your vehicle and trailer carefully
before starting to drive.
Gradients: Where possible, when towing, you should
plan your journey to avoid steep gradients. The advised
Trailer hitch load should never exceed the limit advised by brake towing mass stated assumes a maximum gradient
MG Motor. capability of 12%. Where possible it is recommended
Note: Excessive towing loads reduce front tyre traction you drive on gradients less than 12%. Follow the trailer
and steering control, too little trailer nose load can associations recommendations for suitable roads.
make the trailer unstable and cause it to sway.
243
STARTING & DRIVING
Running in period: Avoid towing a trailer during your
vehicles first 625 miles 1000 km.
Stop/Start function: On vehicles fitted with a
Stop/Start function, manually switch the Automated
Stop/Start function OFF when towing. The trailer weight
can affect your vehicle's braking efficiency if Automated
Stop/Start is activated on a hill while towing a trailer.
244
Emergency Information
246 Hazard Warning Devices
247 eCall - SOS Emergency Assistance
250 Emergency Starting
252 Vehicle Recovery
256 Tyre Repair
264 Fuse Replacement
271 Bulb Replacement 5
EMERGENCY INFORMATION
Hazard Warning Devices metres behind the car, if possible, and press the hazard
warning switch to warn other road users of your position.
Warning Triangle
The warning triangle supplied with your car is stowed in

the loadspace.
If you have to stop your car on the road in an emergency,
you must place a warning triangle approximately 50 - 150
246
eCall - SOS Emergency Assistance When the eCall triggers, the system will only transmit the
data information to the relevant public safety answering
In an accident, your vehicle’s eCall – SOS Emergency points designated by the respective public authorities of
Assistance can either be triggered manually or in severe the country on which territory they are located, which
cases automatically upon detection by vehicle’s sensors. will receive and process your emergency call request. The
The eCall service is a public service of general interest and system will retain data locally within 13 hours of triggering.
is accessible free of charge. The emergency call centre will
You have the right to access the data information stored
establish verbal communication with the vehicle occupants
in this system, and to request the rectification, erasure
in order to understand the extent of the emergency and
or blocking of data information that does not meet the
the level of assistance required. If verbal communication
requirements of the regulations. When you think your
is not achievable an attempt will be made to send the
personal data is infringed, you have the right to complain
following vehicle information message to the emergency
to the competent data protection authority.
call centre. The appropriate emergency services will be 5
deployed to the vehicle’s current location if known. For manual activation, press and release the SOS button
• Current time, location and direction of travel in the overhead console for about 1 second to activate an
• Vehicle type emergency services call. A single beep will be heard when
the eCall is triggered and a message will be displayed on
• Vehicle identification number (VIN)
the vehicle’s message centre and entertainment player. The
• Whether the call was automatically or manually initiated
entertainment player will be muted whilst the emergency
• Vehicle category services call is active. Manually triggered emergency
This system will ensure that your personal data is securely services calls may be cancelled by pressing and releasing
protected. It is designed to ensure that it is not traceable the SOS button again within about 5 seconds of the initial
and other external systems are not able to gain access. press, and the messages will be removed.
247
The emergency services call (eCall) system will perform a fault is detected. Faults detected during the self-test will
self-test when the vehicle power system/ignition is turned be displayed on the vehicles message centre.
ON. During a Self-Test the emergency services call (eCall)
Note: The operation of eCall - SOS Emergency
LED status indicator on the SOS button will flash quickly
Assistance relies on cellular coverage and may be
until completion. The LED status indicator will illuminate
affected by signal outages or low signal strength.
permenantly if no system faults are present. The LED
status indicator will be extinguished or flash slowly if a
248
Note: The automatic emergency services call (eCall)
function may be disabled by a local MG Authorised
Repairer upon request.
Note: It is strongly recommended the eCall function is

not disabled, any action requested by the owner must
be accompanied by a signed request.
249
Emergency Starting
A
NEVER attempt to power the vehicle by
pushing or towing.
Make sure that both batteries are of the same

rated voltage (12 volts), and that the booster
cables are approved for use with 12 volt car
batteries.
Ensure sparks and naked flames are kept well

away from the front compartment. B
Ensure that each booster cable connection

is securely made. There must be no risk of Ensure the START/STOP Switch is turned off and switch
touching each other or other moving parts, off ALL electrical equipment of BOTH vehicles, then follow
this could cause sparking, which could lead the instructions below:
to fire or explosion. 1 Connect the RED booster cable between the positive
(+) terminals of both batteries. Connect the BLACK
When the battery loses power, the booster cables can be booster cable from the negative (-) terminal of the
used to connect the battery of a donor vehicle or external donor battery (A) to a good earth point (CCU housing
battery to start the vehicle. or other unpainted surface, for example), as far away
250
from the battery as possible and well away from brake 4 After both the vehicles have normally
lines on the disabled vehicle (B). started/powered, turn off the START/STOP Switch of
the donor vehicle.
5 Disconnecting the booster cables must be an exact
reversal of the procedure used to connect them, i.e.
disconnect the BLACK cable from the earth point on
the disabled vehicle FIRST.
IMPORTANT
DO NOT switch on any electrical appliance in the

disabled vehicle until the booster cables have been
disconnected.
5
Note: It is recommended to turn off lighting, air
conditioning and other comfort appliances, and
ensure that the disabled vehicle remains powered or
runs for more than 1~2 hours after it is started, in
2 Power up or start the donor vehicle and allow it to
order to recover the battery power. If the vehicle
run for a few minutes.
still fails to start/power normally after full charging,
3 Power up or start the disabled vehicle. If the disabled please contact an MG Authorised Repairer.
vehicle does not power up or start after several
attempts, it may need to be repaired. Please contact
an MG Authorised Repairer.
251
Vehicle Recovery
Towing for Recovery
Towing Hook
When pushing or towing the vehicle from a dangerous situation or onto the transporter, the speed must
remain below 3mph and be completed within 3 minutes.
When pushing or towing the vehicle onto the transporter, the driver's side seat belt should be inserted
into the lock and maintained in the inserted state in order to release the EPB.
DO NOT use a tow rope that is twisted - or the towing hook may be unscrewed.
DO NOT tow the vehicle with any of the driven wheels in contact with the road surface, this will avoid
electric drive transmission damage.
252
Your car is equipped with 2 towing eyes (located at the front and the rear of the vehicle), which are used for fitting the
towing hook. The towing hook is placed beneath the loadspace floor. To fit the towing hook, remove the small cover set
into the bumper, first press one end of the small cover plate, then open the small cover plate after the other end is lifted,
then screw in the towing hook via the small hole into the threaded hole in the bumper beam (see illustration). Ensure the
towing hook is fully tightened!
Note: The towing eye cover may be secured to the bumper by a plastic cord.
253
Both towing points are intended for use by qualified recovery specialists to assist in the recovery of your car when a
breakdown or accident occur. They are not designed for towing other vehicles, and must NEVER be used to tow a trailer
or caravan. The vehicle can be towed using a tow rope but a towing bar is recommended.
Towing for Recovery
When towing, DO NOT suddenly accelerate

or brake suddenly, this can cause accidents.
Suspended Towing
Suspended towing is the best method for recovering a
vehicle that needs to be towed. The drive wheels MUST be
suspended above the ground. Ensure the EPB is released
when the rear wheels are in contact with the road surface.
Switch the hazard lamps ON and ensure no passengers are
in the vehicle.
254
Transporter or Trailer 3 Fit the lashing straps (3) around the wheels and secure
to the trailer. Tighten the straps until the car is
If your car is to be transported on the back of a trailer or
securely held.
transporter, it must be secured as illustrated:
1 Apply the parking brake and place the electric drive

transmission in park.
2 Fit wheel chocks (1) as shown, then position the anti
slip rubber blocks (2) around the circumference of the
tyre.
255
Tyre Repair first during the first inflation operation, and then
screw off the dust cap when there is enough space.
Your vehicle is equipped with low wind resistance wheel
Note: If the pulling force required to remove the wheel
trim covers, which are fixed by snaps. If you need to
trim cover is large, use a suitable tool to pull it out.
remove or install the wheel trim cover, please pay attention
to the following precautions:
• When removing the trim cover, it's better to pull the
trim cover apart at several positions similar to 1 (see
1
illustration). Please DO NOT pull the trim cover at
other positions to avoid damaging it;
• When removing the trim cover, pull the five best pulling
points one by one, and remove the wheel trim cover as
a whole after all of them are pulled apart;
• When installing the trim cover, please check the valve
mark on the back of the trim cover (as shown in the
enlarged illustration), align the nearest hollow of the
trim cover next to it with the valve on the wheel, and
then install it to ensure that the valve can be exposed
from the hollow. And then clamp the trim cover in
place.
Note: When the new vehicle leaves the factory, the
dust cap of the valve may be a little tight. It is
recommended that you remove the wheel trim cover
256
Tool Identification Tyre Repair
1 Remove the label at the bottom of the repair fluid
2 3 4 reservoir and attach it to the steering wheel to remind
the driver not to exceed 50 mph.
max. 80km/h
5 max. 50mph
max.
max.
80
50
km/h
mph
1 Repair Fluid
2 Electric Air Pump
3 Towing Hook 2 Connect the air hose of the electric air pump to
the repair fluid reservoir, fit the tyre sealant bottle
4 Wheel Bolt Cap Removal Tool
(upright) into the slot on the compressor. Remove
5 Warning Triangle the valve dust cap of the flat tyre, and connect the
filler hose from the tyre sealant bottle to the tyre
257
valve. Ensure that the power switch of the electric 3 Switch on the power switch of the electric compressor
air compressor is switched off (i.e., press “O”), then (i.e., press “-”), to start pumping sealant into the
insert the plug from the compressor into the centre tyre. The tyre sealant bottle will become empty after
console power socket, and turn the vehicle power approximately 30 seconds. The tyre should reach the
system to ON/READY. specified pressure within 5 or 10 minutes.
Note: The pressure gauge may briefly reach 6
S TA R T
bar (87 psi), then the pressure begins to drop to
normal.
S TA R T
S TO P
4 When the required pressure is reached, switch off the
power switch of the electric compressor (i.e., press
“O”).
Note: If the required pressure cannot be
reached within 10 minutes, please disconnect
the compressor, drive the vehicle 10 metres (33
feet) approx forward or backward to allow the
sealant to spread within the tyre. If the required
pressure can still not be reached, the tyre is
Note: To avoid battery discharge, it is severely damaged and you should seek assistance
recommended to keep the vehicle in P and READY from the Roadside Assistance company or an MG
mode. Authorised Repairer.
258
Note: Continual operation of the electric air • If the tyre pressure has dropped to less than 0.8 bar
compressor for more than 10 minutes may result (11.6 psi), do not continue driving, seek assistance
in damage to the compressor. instead.
• If the tyre pressure is between 0.8 bar (11.6 psi)
Note: Under no circumstances should you
and specified pressure, use the electric air pump
continue your journey with a deflated tyre.
to inflate the tyre until it reaches the specified
Driving a vehicle with a deflated tyre is extremely
pressure. Repeat the operations of step 6.
dangerous.
• If the tyre pressure has not dropped, you may
5 Remove the tyre sealant bottle from the slot in the continue driving, but the vehicle speed must not
compressor, disconnect the hose from the tyre valve, exceed 50 mph, and the driving mileage must not
remove the compressor plug from the centre console exceed 125 miles.
power socket, return the tyre repair kit to its stowage
Note: Please regularly check the tyre sealant 'use by 5
tray.
date' and replace as necessary.
6 After successfully adding sealant to the tyre, drive
Note: DO NOT remove foreign objects (eg.
immediately for a short time (around one minute).
screws,nails) from the tyre. The tyre repair system
This will allow the sealant to distribute evenly inside
must only be used when the foreign object is in the
the tyre. Continue driving and do not exceed 50 mph.
tread pattern (A), DO NOT attempt a repair when
After a further 10 minutes, find a safe place to stop
the damage is in the sidewall of the tyre (B).
and recheck the tyre pressure.
Please follow different guidelines based on the tyre
pressure measured:
259
*
Changing a Wheel
If you need to change the wheel during the journey, choose
a safe place to stop away from the main road if possible.
Always ask your passengers to get out of the car and wait
A B B
in a safe area away from other traffic.
Switch on hazard warning lamps. If available, position
a warning triangle about 50 to 150 metres behind your
vehicle to warn approaching traffic.
Before changing a wheel, ensure the front wheels are in
the straight ahead position. Apply the parking brake and ,
where possible ensure P is selected.
Observe the following precautions:
• Ensure the jack is positioned on firm, level ground.
• If the vehicle must be parked on the hill, place chocks in
front of and behind the other 3 wheels to prevent the
vehicle moving.
260
Positioning the Jack Avoid accidental contact with any underbody
NEVER work beneath the car with the jack parts, the high voltage battery casing.
as the only means of support. The jack is
designed for wheel changing only! Position the jack on firm level ground under the jacking
point nearest the wheel to be removed. Note that the
NEVER jack the car using any jacking points domed head of the jack must fit into the corresponding
other than the recommended jacking points. recess in the sill plate (There is a triangle indicator in the
Serious damage to the car could result. area shown by the arrowhead.).
Turning the jack screw by hand, adjust the jack until the jack
head fits snugly onto the sill in the correct area. Ensure that
the base of the jack is in full contact with the level ground.
Fitting the Spare Wheel 5

Regularly check the spare wheel tyre
pressure, it may not be used for long
periods of time. After fitment, at the first
opportunity check and adjust the tyre
pressure.
The wheel bolts must be tightened to the
specified torque after changing a wheel
(120 ～ 130 Nm).
261
1 Before raising the car, remove the wheel trim cover. toolbox in the well in the load space floor (face down).
Use the wheel bolt spanner to slacken each bolt half a Lower the boot floor, and put the boot storage box on
turn anti-clockwise. the boot floor.
2 Turn the handle in a clockwise direction until the tyre Note: DO NOT stand on the handle of the wheel bolt
is clear of the ground. spanner or use extension tube on the handle of the
spanner.
3 Remove the wheel bolts and place them in the tool tray
to prevent them from being lost. Make sure the vehicle Note: When replacing the wheel, please fully tighten
is steady and there is no risk of slip or movement the bolts in the diagonal sequence twice.
before removing wheel bolts.
Note: Consult your MG Authorised Repairer. or tyre
4 Remove the road wheel.
specialist for a replacement tyre, as soon as possible.
Note: Avoid placing wheels face down on the
Spacesaver Spare Wheel
ground - the surface may be scratched.
Only one spacesaver spare wheel can be used
5 Fit the spare wheel and tighten the wheel bolts with
at any one time, otherwise the operational
wheel bolt spanner until the wheel is seated firmly
performance and brake performance may be
against the hub.
reduced, thereby leading to accident or injury
6 Lower the car and remove the jack, then FULLY tighten to yourself and others.
the wheel bolts in a diagonal sequence.
7 Finally, return the tools to the toolbox, put the toolbox
into the well of the boot floor, tighten the spare wheel
retaining nuts, and put the replaced wheel above the
262
When driving on icy or slippery surfaces it is
advised to fit the spacesaver wheel to the rear
of the vehicle to maintain adaquate stability.
This may mean swapping a front wheel with
a rear wheel.
Snow chains can not be used on the
spacesaver spare wheel, this can cause
damage to the car and snow chain.
When the spacesaver spare wheel is fitted, the vehicle

speed should not exceed 50 mph. Please have the full-scale
tyre repaired and replace the spare wheel as soon as
possible. This will extend the life span of the spare wheel 5
for other emergencies.
Note: DO NOT use an automatic car wash when
the spacesaver wheel is fitted, the guide rails of the
car wash may conflict with the wheel/tyre and cause
damage.
263
Fuse Replacement Fuse Box
There are two fuse boxes in the vehicle：
Fuse
Fuses are simple circuit breakers which protect the vehicle
electrical equipment by preventing the electrical circuits
from being overloaded. A blown fuse results in the item
of electrical equipment it protects failing to work.
Check a suspect fuse by removing it from the fuse box and
looking for a break in the wire inside the fuse.
It is recommended to have spare fuses in the vehicle, these 1 2
can be obtained from a local MG Authorised Repairer.
00000000000000000
00000000000000000
0000
00000000000000000
0000
00000000000000000
0000
00000000000000000
0000
00000000000000000
0000
00000000000000000
00000000000000000
00000000000000000
00000000000000000
IMPORTANT 00000000000000000
00000000000000000
• NEVER attempt to repair a blown fuse. ALWAYS

replace a fuse with one of the same rating.
• If a replaced fuse fails immediately, please contact an
1 Front Compartment Fuse Box（at the left side of the
MG Authorised Repairer as soon as possible.
Front Bay）.
2 Passenger Compartment Fuse Box（below the glove
box at the front passenger side）.
264
Passenger Compartment Fuse Box 3 Press the fuse extraction tool onto the fuse head
and pull to remove the fuse. A blown fuse can be
recognised by a break in the wire.
4 Replace the blown fuse with a same rating.
F41 F40 F39 F38 F37 F36 F35 F34 F7 F6 F5 F4 F3 F2 F1

Fuse Specification
F44 F43 F42

F14 F13 F12 F11 F10 F9 F8 NO. Specs Function
R5
R4 R3 R2 R1
F23 F22 F21 F20 F19 F18 F17 F16 F15
Charging Plug Lock Relay,
F1 5A
F33 F32 F31 F30 F29 F28 F27 F26 F25 F24 Charging Plug Unlock Relay
F2 10A Diagnostic Line Connector
Combined Charging Unit, 5

Electric Vehicle Communication
F3 5A
Controller, Battery Pressure
Check or Replace a Fuse Alarm Switch
1 Switch off the vehicle power system and all electrical
Front Washer Relay, Rear
equipment, disconnect the battery negative cable. F4 15A
Washer Relay
2 Remove the closing panel below the glove box to gain
access to the fuse box. F5 5A Sensing Diagnostic Module
F6 5A High Voltage PTC, ESS PTC
265
NO. Specs Function NO. Specs Function
F7 10A Energy Storage System F17 5A Phone Wireless Charger
EPB Switch, Tyre Pressure F18 5A Rear USB

F8 5A
Monitoring System
F19 5A E-Call TBOX
F9 5A Vehicle Control Unit
F20 5A TBOX
F10 10A Pedestrian Alert Control Module
Around View Module, Radio
Passive Entry Passive Start F21 10A Broadcasting Reception Module,
F11 5A
Module Front Central Display
F12 5A Power Electronic Box F22 10A Exterior Mirrors Heating Element
F13 30A Driver Seat Adjust Switch Rear Windscreen Heating

F23 25A
Element
F14 5A Backup Immobilizer Coil
Front Infotainment Control
F15 15A Front Power Socket F24 20A
Module
Outside Mirror and Master Light
Automatic Temperature
Height Adjust Switch, Top USB, F25 15A
F16 5A Controller
Left Headlamp Assembly, Right
Headlamp Assembly F26 5A Instrument Pack
266
Information Faceplate, Outside F42 40A Stability Control Module(Valve)

Mirror and Master Light Height
F27 10A Driver Window Lifter, Rear Right
Adjust Switch, Driver Door F43 30A
Window Lift Switch
Switch Pack
Passenger Window lift Switch,
Rear Driving Assistance System, F44 30A
F28 5A Rear Left Window Lift Switch
Rain Light Sensor
F29 10A Gateway
F30 10A Gateway
F31 30A Sunroof Motor 5

F32 30A Sunshade Motor
F33 5A Shift Control Unit
F34 10A Electronic Steering Column Lock
F35 15A Super Lock Relay
F36 5A Charging Flap Motor
F37–41 －－
267
Front Compartment Fuse Box Check or Replace a Fuse
1 Switch off the vehicle power system and all electrical
equipment, disconnect the battery negative cable.
FL2 F14 R LY 1 8 R LY 1 9
F23 2 Press the locating clips to remove the fuse box lid.
R LY 6 F22 R LY 2
FL17
FL14
3 Press the fuse extraction tool onto the fuse head
FL3 R LY 3
F12 F2 F6 F15 F8 F27 F4 F13 F5
FL16
and pull to remove the fuse. A blown fuse can be
R LY 1 7
FL4
FL13
recognized by a break in the wire.
FL12 FL8 FL10 F28
F3 F1 F21 F25 F29 R LY 2 0
R LY 9
F9
F17
R LY 4
F26 F30
4 Replace the fuse with a same rating.
R LY 1
F 11 F 1 0 F 2 4 FL9 R LY 1 6 FL7
FL5 F19 F18
R LY 8
F20
Fuse Specification
FL6
FL1 R LY 1 0 F7 R LY 5
R LY 7
FL15
F16 F L 11
NO. Specs Function
FL1 200A Combined Charging Unit
FL2 80A Electric Power Steering Module
FL3 40A Cooling Fan Relay Pack
Passenger Compartment Fuse

FL4 80A
F1-F7, F19-F21, F34, F35, F42, F44
268
Windscreen/Mirror Heating Relay, Electric Parking Motor Control

FL16 30A
FL5 80A Passenger Compartment Fuse Unit
F8-F14, F24-F33, F43
FL17 40A EVP Relay
FL6 －－
F1 －－
Automatic Temperature
FL7 40A PEB Coolant Pump, Cooling Fan
Controller, Blower F2 15A
Relay Pack
FL8 20A Body Control Module
F3 －－
FL9 40A Stability Control Module(Pump)
F4 －－
FL10 30A Body Control Module 5
Electric Air Conditioning
F5 10A
FL11 －－ Compressor
FL12 20A Body Control Module F6 －－
FL13 －－ Front Wiper Enable Relay, Front

F7 30A
Wiper High/Low Speed Relay
FL14 －－
F8 －－
FL15 30A KLR Relay
F9 －－
269
F10 10A Right Headlamp Assembly F24 －－
F11 10A Left Headlamp Assembly F25 15A Body Control Module
F12 －－ F26 －－
F13 15A Horn Relay Body Control Module, EVP Relay,

F27 5A
Front Breathing Lamp
F14 －－
F28 15A ESS Coolant Pump Relay
F15 5A Brake Pedal Switch
F29 －－
F16 15A Rear Wiper Relay
Shift Control Unit, Body Control
F17 －－
Module, Instrument Pack, PDC
F18 5A Sensing Diagnostic Module Sensor, Front View Control
F30 10A
Module, Front Detection Radar,
F19 5A Vehicle Control Unit E-Call TBOX, Airbag Display
F20 －－ Module
F21 15A Body Control Module
F22 10A Front Left Seat Heating Relay
F23 10A Front Right Seat Heating Relay
270
Bulb Replacement
Bulb Specification
Lamp Bulb Specifications Lamp Bulb Specifications

Headlamp High/Low Stop Lamps LED
LED
Beam
License Plate Lamps W5W 5W
Front Direction
LED
Indicators Rear Fog Lamps LED
Daytime Running Lamps LED High Mounted Stop Lamp LED
Front Side Light LED Interior Lamp (bulb
W5W 5W 5
configuration)
Reverse Lamps W16W 16W
Interior Lamp (LED
Rear Direction Indicators WY16W 16W LED
configuration)
Rear Side Light LED Load Space Lamp C10W 10W
271
Bulb Replacement Reverse Lamps Bulb Renewal
Before replacing any bulb, turn off the START/STOP Switch 1 Open the tailgate.
and lighting switch to avoid any possibility of a short circuit. 2 Disconnect the battery negative terminal.
Note: MG only recommends replacement bulbs that 3 Using a suitable pry bar or lever, carefully remove the
completely meet the manufacturers specifications. cover trim.
Take care NOT to touch the glass with your fingers; always 4 Using a suitable spanner/socket wrench, remove the 3
use a cloth to handle the bulb. If necessary, clean the glass screws (1) securing the lamp to the tailgate. Remove
with methylated spirits to remove fingerprints. the wiring connector (2). Release the lamp assembly
If in doubt, when replacing bulbs, contact an MG and remove away from the body.
For replacement of other bulbs not listed please consult an
272
1
1
0
0
2 1
5
5 Rotate the bulb holder in an anti-clockwise direction. 6 Remove bulb holder and remove bulb.
7 Fit new bulb to bulb holder.
8 Insert bulb holder in lamp assembly, rotate clockwise
until fully secure.
9 Ensure lamp seal is correctly located.
10 Position lamp to tailgate, refit the wiring connector
and the screw fixings, and tighten to 2.7-3.3 Nm.
273
11 Refit screw cover trim. License Plate Lamps Bulb Renewal
12 Reconnect battery negative terminal. 1 Disconnect the battery negative terminal.
13 Test lamp operation. 2 For license plate lamps bulb replacement, it is

necessary to remove the rear bumper cover, seek
14 Close tailgate. guidance from an Authorised MG Repairer.
3 Remove the wiring connector.
4 Rotate the bulb holder in an anti-clockwise direction.
274
5 Remove bulb holder and remove bulb. Rear Direction Indicator Bulb Renewal
6 Fit new bulb to bulb holder. 1 Open the tailgate.
7 Insert bulb holder in lamp assembly, rotate clockwise 2 Disconnect the battery negative terminal.
until fully secure. 3 Using a suitable pry bar or lever, carefully release and
8 Refit the wiring connector. remove the securing screw cover trim.
9 Fit the rear bumper cover. 4 Using a suitable spanner/socket wrench, remove the 2
screws securing the lamp to the body.
10 Reconnect battery negative terminal.
11 Test lamp operation.
275
5 Remove the wiring connector. Release the lamp 10 Ensure lamp seal is correctly located.
assembly and remove away from the body.
11 Position lamp to body, refit the wiring connector, start
6 Rotate the bulb holder in an anti-clockwise direction. both screw fixings, and tighten to 3-5 Nm.
12 Refit screw cover trim.
13 Reconnect battery negative terminal.
15 Close tailgate.
7 Remove bulb holder and remove bulb.

8 Fit new bulb to bulb holder.
9 Insert bulb holder in lamp assembly, rotate clockwise
until fully secure.
276
Interior Lamp Bulb Renewal assembly. Push the lens upwards until it ‘clicks’ into
1 Disconnect the battery negative terminal. position
2 Lightly prize off the lamp lens from the lamp assembly 6 Connect battery negative terminal.
using a flat-blade screwdriver. 7 Test lamp operation.
3 Pull the bulb from its mounting to remove.

4 Install new bulb.
5 Install the lens, locate the two prongs at the front
of the lens and then carefully flex the lens to locate
the two prongs at the rear of the lens into the lamp
277
Load Space Lamp Bulb Renewal 9 Close tailgate.
1 Open the tailgate.
2 Disconnect the battery negative terminal.
3 Insert a suitable tool or small flat bladed screwdriver
into the indent on one of the narrow sides of the lens
and carefully remove the unit from its location.
4 Push against spring pressure and lift the bulb to remove

it.
5 Install new bulb.
6 Refit the unit, push until fully secured.
7 Connect battery negative terminal.
278
Maintenance
280 Maintenance
283 Bonnet
285 Front Compartment
286 Cooling System
288 Brake
290 Battery
292 High Voltage Battery Pack
294 Washer
296 Wipers 6
299 Tyre
305 Cleaning and Vehicle Care
MAINTENANCE
Maintenance Brake Fluid Replacement
Replace the brake fluid according to the information
Routine Servicing
contained in the "Service Schedule" - see www.mg.co.uk -
The safety, reliability and performance of your car will owners section.
depend partly on how well it is maintained. You must
ensure that maintenance is carried out when required and Note: Brake fluid replacement will be an additional
according to the information contained in the "Service cost.
Schedule" - see www.mg.co.uk - owners section.
Coolant Replacement
Servicing The coolant (anti-freeze and water solution) needs to be
For next service information please consult your service replaced according to the information contained in the
records. "Service Schedule" - see www.mg.co.uk - owners section.
Some markets feature a service reminder in the IPK Note: Coolant replacement will be an additional cost.
message centre.
Service History
Ensure MG Authorised Repairer registers the Service
History after each service.
280
MAINTENANCE
Owner Maintenance Special Operating Conditions
Any significant or sudden drop in fluid levels, If your car is frequently used in dusty conditions, or
or uneven tyre wear, should be reported operated in extreme climates where sub-zero or very
without delay to MG Authorised Repairer. high ambient temperatures are normal, more frequent
attention may need to be paid to servicing requirements.
In addition to the routine services referred to previously, You need to carry out special maintenance operations
a number of simple checks must be carried out more (refer to Service Schedule) or contact an MG Authorised
frequently. Advice is given on the pages that follow. Repairer.
Daily Check
Safety in the Garage
• Operation of lights, horn, wipers, washers and warning
lamps. Cooling fans may commence operating after
• Operation of seat belts and brakes. the vehicle is switched off, and continue
operating for a number of minutes. Keep
• Look for fluid deposits underneath the car that might
clear of all fans while working in the front
indicate a leak.
• Check tyre appearance.
motor compartment 6
Weekly Check If you need to carry out maintenance, observe the
• Coolant levels. following safety precautions at all times:
• Brake fluid level. • If the car has been driven recently, DO NOT TOUCH
• Windscreen washer fluid level. cooling system components until the drive motor has
• Operate air conditioning. been fully cooled down.
281
MAINTENANCE
• DO NOT TOUCH electrical leads or components
when the START/STOP Switch is on.
• DO NOT work underneath the car with a wheel
changing jack as the only means of support.
• Wear protective clothing and work gloves.
• Remove watches and jewelery before working in the
front compartment.
• DO NOT allow tools or metal parts of the car to make
contact with the battery leads or terminals.
Toxic Liquid
Fluids used in motor vehicles are poisonous and should
not be consumed or brought into contact with open
wounds. These include: battery acid, coolant, brake fluid
and windscreen washer fluid.
For your own safety, ALWAYS read and obey all
instructions printed on labels and containers.
282
MAINTENANCE
Bonnet 1 From the inside of the vehicle, pull the bonnet release
handle (Figure A).
Opening the Bonnet
2 Move the safety catch release handle on the bonnet
DO NOT drive when the bonnet is not closed lock assembly in the direction of the arrow (Figure B)
or retained only by the safety catch. to release the bonnet safety catch.
3 Raise the bonnet and hold it up with the support rod
firmly.
Closing the Bonnet

Support the bonnet by one hand, release the support rod
0000000000000
0000000000000
0000000000000
0000000000000
0000000000000
0000000000000
using the other hand, and place it firmly into the support
0000000000000
rod base. Then hold the bonnet using both hands and
0000000000000
0000000000000
0000000000000
0000000000000
0000000000000
0000000000000
0000000000000
0000000000000
lower it, allowing it to drop for the last 20 cm～30 cm

0000000000000
0000000000000
to fully close the bonnet.

6
By attempting to lift the front edge of the bonnet, check if
00 the lock is fully engaged after closing the bonnet. If it is not
fully engaged, you must repeat the operation.
A B
Bonnet Open Warning
If the bonnet is not fully engaged, when the vehicle power
system is in the ON/READY position, the corresponding
283
MAINTENANCE
alarm icon will be displayed in the information message
centre of the instrument pack. If it is detected that the
bonnet is not fully engaged whilst driving, an audible
warning will sound.
IMPORTANT
• For safety reasons, the bonnet should be fully latched

and secure when driving. Therefore every time the
bonnet is opened, you must check after closing that
the bonnet is securely latched, e.g. the bonnet edge
is flush with the body of the car.
• You should stop the car immediately when safety
permits and close the bonnet if it is not closed fully
when driving.
• Beware of injury to hands while fully closing the
bonnet with a downward force.
284
MAINTENANCE
Front Compartment
While working in the front compartment, always observe the safety precautions listed under ‘Safety in
the Garage’, refer to ‘Maintenance’ in ‘Maintenance’ section.
1 Washer fluid reservoir (blue cap)

1 2 3 4 2 Battery coolant expansion box （ black
cap）
3 Brake fluid reservoir (yellow/black cap)
4 Electric drive transmission coolant
expansion box（black cap）
285
MAINTENANCE
Cooling System 2 Electric Drive Transmission Coolant Expansion Tank
The cooling system should be checked weekly when the
Coolant Check and Top Up
cooling system is cold and with the car resting on level
DO NOT remove the coolant expansion tank ground. If the coolant level is below the "MIN" mark,
cap when the cooling system is hot - escaping remove the coolant expansion tank cap and top up coolant.
steam or hot coolant could cause serious The coolant level should not be higher than the "MAX"
injury. mark.
Note: Prevent coolant from coming into contact
with the vehicle body when topping up. Coolant will
damage paint.
If the coolant level falls appreciably during a short period,
and you suspect that there may be a leak, please seek an
Authorised Repairer for service.
Coolant Specification
1 2 Please use the coolant which is recommended and
certified. Please refer to ‘Recommended Fluids and
Capacities’ in the "Technical Data" section.
Note: The addition of corrosion inhibitors or other
additives to the cooling system of this car may severely
1 Battery Coolant Expansion Tank disrupt the efficiency of the system and cause parts
286
MAINTENANCE
damage. For cooling system issues please consult an
Coolant is poisonous and can be fatal if
swallowed - keep coolant containers sealed
and out of the reach of children. If accidental
contact of coolant by children is suspected,
seek medical assistance immediately.
Prevent the coolant from coming into contact

with the skin or eyes. If this occurs, rinse
immediately with plenty of water. If eyes
are still red, painful or uncomfortable, seek
medical attention immediately.
287
MAINTENANCE
Brake Brake Fluid Check and Top Up
Brake fluid is highly toxic, keep containers
Brake pads
sealed and out of the reach of children. If
DO NOT rest your foot on the brake pedal accidental contact of brake fluid is suspected,
while driving, this may overheat the brakes, seek medical attention immediately.
reduce their efficiency and cause excessive
wear. Prevent brake fluid coming into contact
with the skin or eyes. If this occurs, rinse
Wear rates for brake pads and discs may vary. The immediately with plenty of water. If eyes
recommended minimum thickness for brake pads is 2 mm, are still red, painful or uncomfortable, seek
for front brake discs is 23-25 mm and rear brake discs is medical attention immediately.
8-10 mm.
For the first 900 miles (1500 km), you should avoid The brake fluid level should be checked weekly when the
situations where heavy braking is required. system is cold and with the car on level ground.
Remember that regular servicing is vital to ensure that The fluid level can be seen through the reservoir and should
all the brake components are examined for wear at the be maintained between 'MAX' and 'MIN' mark.
correct intervals, and replaced when required to ensure Note: Do not allow the fluid level to drop below 'MIN'
long term safety and optimum performance during the mark or rise above 'MAX' mark.
interval prescribed in Service Portfolio.
The car needs to run in for 500 miles (800 km) after brake
pad or brake disc replacement.
288
MAINTENANCE
Brake Fluid Specification
Use the brake fluid recommended and certified by
the manufacturer. Refer to ‘Recommended Fluids and
Capacities’ in ‘Technical Data’ chapter.
IMPORTANT
Replace brake fluid regularly according to the Service

Portfolio.
Note: Brake fluid will damage painted surfaces. If

you accidentally spill the brake fluid on the painted 6
surface, soak up any spillage with an absorbent cloth
immediately and wash the area with water or car
shampoo.
289
MAINTENANCE
Battery Note: It is recommended to ensure the vehicle is
placed in READY mode for half an hour every week
Battery Maintenance to help extend the service life of the battery. If the
vehicle is stored for more than 1 month, remove the
DO NOT leave electric components switched
negative terminal from the battery. Make sure that
on when not in READY mode, this may cause
the vehicle power system has been turned off before
the battery to become flat, resulting in the
connecting or disconnecting the negative terminal.
failure of the ability to set vehicle into READY
mode and the reduction of battery life.
Always store batteries upright, tilting may

allow the corrosive substances contained
within the battery to leak out.
Never attempt to dismantle a battery, they

are sealed units.
The battery is located in the front compartment and is

maintenance-free, therefore there is no need to refill fluid.
According to the current load condition and battery
status, the system may limit the power of some electrical
appliances. Please ensure the vehicle is placed in READY
mode as soon as possible to charge the battery.
290
MAINTENANCE
Battery Replacement
The battery contains sulphuric acid, which is
corrosive.
Please go to an MG Authorised Repairer to remove and

refit the battery. Only fit a replacement battery of the
same type and specification as the original to maintain the
correct vehicle functionality.
The used battery should not be discarded at will,

for it is harmful to the environment. It must be recycled by
professional institutes. Please consult an MG Authorised
Repairer for more details.
291
MAINTENANCE
High Voltage Battery Pack DO NOT attempt to dismantle the battery
pack or any High Voltage components -
Precautions and restricted conditions for THESE ARE DANGEROUS. Any signs of
use of battery dismantling or damage caused by attempts
If the vehicle is not going to be used, parked, to dismantle will invalidate the warranty.
or stored for a long time it is necessary to
charge the vehicle at least once every 3 When using a paint curing oven please
months. During this time, the High Voltage observe the following:
battery state of charge should not be allowed Before and after any paint baking process,
to drop below 50%. the vehicle should be parked at room
temperature (20 ± 2 ℃) for 24 hours.
If the battery is in a low state of charge and The vehicle can be used normally after
the instrument pack displays no valid driving being parked for 24 hours. The baking oven
range, the vehicle MUST NOT be left in a temperature should not exceed 80 ℃ and
stored state for more than 7 days without the baking time should not be longer than 30
being charged to above 50%. minutes.
1 DO NOT park the vehicle in conditions where the

Failure to follow these guidelines will result ambient temperature exceeds 45℃ for more than 15
in HV battery damage and invalidate the days. This will effect the performance and service life
warranty. of the high voltage battery.
2 To maintain or improve the service life of the high
voltage battery, it is recommended that you use a slow
292
MAINTENANCE
charging method wherever possible, rapid charging 5 In the event of an accident, damage to the high
should only be used for long distance journeys or voltage battery or any of its related components, or
emergencies. any repairs made to the high voltage system the car
must be inspected by qualified personel at an MG
3 It is recommended using the vehicle at least once a
month.
6 In the event of any accident or body repairs being
Where possible it is recommended that you carry
required please consult the qualified personnel at an
out a slow charge (equalisation charging) every month
MG Authorised Repairer. The repair may require high
to extend the service life of high-voltage battery
voltage battery isolation or specialist HV component
pack. The battery management system will monitor
removal.
the status of the high voltage battery pack. After
monitoring for a period of time, if an equalisation IMPORTANT
charge has not been carried out for some time the
Only fully trained and qualified personel are
message centre in the instrument pack will display
allowed to work on the high voltage systems and
‘Please Slow-charge the Vehicle’. At this time you must
components of this vehicle. Any disassembly of
carry out an equalisation charge. For operation mode,
such systems or components is strictly prohibited.
6
please refer to ‘Equalisation Charging’ in ‘Starting &
Driving’ section.
4 When the vehicle is used for the first time or after
a long period of storage, the SOC displayed in the
instrument pack may not be accurate. A full charge
is recommended before use. (Battery pack type 2)
293
MAINTENANCE
Washer Note: DO NOT use an anti-freeze or vinegar/water
solution in the washer reservoir - anti-freeze will
Washer Fluid Check and Top Up damage paintwork while vinegar will damage the
washer pump.
Windscreen washer fluid is flammable. DO
NOT allow windscreen washer fluid to come
into contact with naked flames or sources
of ignition.
When filling the washer fluid, DO NOT let the
00
washer fluid spill on parts around the engine,
motor, electric drive transmission or on the
paint surface of the vehicle body. In case the
washer fluid is spilled on hands or other parts
of the body, please immediately wash with
clean water.
The washer fluid is used to clean the windshield. Check

the washer fluid level regularly. When the level of washer
fluid is low, please top up the washer fluid as instructed.
Please use the washer fluid recommended and certified
by the manufacturer. Refer to ‘Recommended Fluids and
Capacities’ in "Technical Data" chapter.
294
MAINTENANCE
IMPORTANT
• Use the washer fluid recommended and certified by

the manufacturer. Misuse of washer fluid in winter
may cause damage to the washer motor due to
freezing.
• Using the washer switch when there is no washer
fluid may cause damage to the washer motor.
• Operating the wipers when the windscreen is dry
and there is no washer fluid may cause damage to
the windscreen and wipers. Please spray the washer
fluid and start the wipers when there is adequate
washer fluid.
Washer Nozzles
6
Operate the washers periodically to check that the nozzles
are clear and properly directed.
If the nozzle is obstructed, insert a needle or thin metal
wire into the hole to remove the obstruction.
295
MAINTENANCE
Wipers
Wiper Blades
IMPORTANT
• Grease, silicon and petrol based products impair the blade's wiping capability. Wash the wiper blades in warm soapy
water and periodically check their condition.
• Clean the windscreen frequently, DO NOT use wipers to remove stubborn or ingrained dirt, it will reduce their
effect and their life span.
• If signs of hardness or cracking in the rubber are found, or if the wipers leave streaks or unwiped areas on the screen,
then the wiper blades should be replaced.
• Clean the windscreen regularly with an approved glass cleaner and ensure the screen is thoroughly cleaned before
fitting replacement wiper blades.
• Only fit replacement wiper blades that are identical to the original specification.
• Clean ice and snow from around wipers and ensure they are not frozen or otherwise sticking to the windscreen
before attempting to operate them.
296
MAINTENANCE
Replacing Front Wiper Blades 3 Press the retaining clips at both sides (as shown in
the figure), whilst pulling the wiper blade outward,
to remove the wiper blade from the wiper arm and
discard.
4 Position the fitting of the new wiper blade into the slot
of the wiper arm.
5 Push the wiper blade towards the wiper arm until it is
located embedded with a click been heard.
6 Place the wiper assembly back on the windscreen.
7 To exit the service mode and return the wipers to
the park position, operate the wiper stalk switch again
by pressing down and releasing, alternatively, set the
vehicle power system to ON.
1 With the bonnet closed, and within 20 seconds 6
of switching the START/STOP Switch to the OFF
position, operate the wiper stalk switch by pressing
down and releasing, the wipers will sweep and stop in
the 'service position' on the windscreen.
2 Lift the wiper arm away from the windscreen.
297
MAINTENANCE
Replacing Rear Wiper Blades 4 Place the wiper assembly back on the rear window.
1 Lift the wiper arm away from the rear window.

2 Rotate the wiper blade as shown in the figure, to
remove it from the wiper arm and discard.
3 Position the fitting of the new wiper blade into the slot
of the wiper arm. Ensure the wiper blade is properly
secured on the wiper arm.
298
MAINTENANCE
Tyre see the damage from the outside, continue driving the
vehicle slowly to the nearest MG Authorised Repairer for
Overview inspection and service.
• New tyres may not have the best adhesive ability at the
Tyre Life
beginning. Therefore, driving your vehicle at moderate
speed and in a prudent way at the first 300 miles, which Correct tyre pressures and moderate driving style can
is also beneficial to the service life of the tyres. extend tyre life. Recommendations:
• Regularly check tyres for signs of damage. DO NOT • Check the tyre pressures at least once a month, it
remove foreign objects such as screws or nails from the should be carried out when the tyre is cold;
tyre. If a tyre shows any signs of damage, please ensure • Avoid cornering at excessive speeds;
it is inspected by a reputable tyre fitter for advice. • Check tyres frequently for abnormal wear;
• The valve dust cap must be fitted to prevent dust from • When the vehicle is to be parked for a long time, the
entering the valve. vehicle should be moved at least once every two weeks
• If the tyre is to be removed, always mark the tyre/wheel to prevent permanent deformation of the tyres due to
orientation to ensure correct reinstallation. long-term stress. 6
• Store the removed wheel or tyre in a cool, dry and dark The following factors affect the tyre life:
place.
The damage of a tyre or rim may happen unnoticed. If Tyre Pressure
abnormal vibration or deviation is experienced, that means Incorrect pressure will cause the abnormal wear of the
the tyre may have been damaged. If you suspect that a tyre, greatly shorten the service life, and have an adverse
tyre is damaged, please slow down immediately, and stop effect on the driving characteristics of the vehicle.
your vehicle to check the tyre for damage. If you can't
299
MAINTENANCE
Driving Style Caring for your Tyres
Excessively harsh acceleration and braking whilst cornering DEFECTIVE TYRES ARE EXTREMELY
will reduce tyre life. DANGEROUS! DO NOT drive if any tyre is
damaged, excessively worn, or incorrectly
Wheel Balance inflated.
Every new vehicle leaves the factory having had the wheels
dynamically balanced. Out of balance wheels may be due It is recommended to install the tyres
to many factors. If wheels are out of balance, shaking or consistent with the original specifications.
vibration of the steering mechanism may occur and the DO NOT replace the tyres with tyres of
tyres may start to wear excessively. It is important to any other type. Alternative tyres, of a
restore wheel balance as quick as possible. Each wheel different specification, may adversely affect
should be rebalanced after installing a new tyre or having a the vehicle's driving characteristics and
tyre repair. safety. In order to retain the original safety
characteristics it is suggested that you consult
Wheel Alignment an MG Authorised Repairer.
Incorrect wheel alignment can cause excessive tyre wear
Always drive with consideration for the condition of the
and affect vehicle safety. If the tyres show signs of abnormal
tyres, and regularly inspect the tread and side walls for any
wear, check the wheel alignment and seek advice from an
sign of distortion (bulges), cuts or wear.
If possible, protect tyres from contamination
by oil, grease and fuel.
300
MAINTENANCE
Tyre Pressure immediately and drive with caution until the spare wheel
can be fitted, or repairs undertaken.
Before a long distance journey, the tyre
pressures should be checked. Note: If the sidewall of the tyre is damaged or
distorted, replace the tyre immediately. Do not
Check the pressures (including the spare wheel if fitted) at attempt a repair.
least every month. Carry out pressure checks when the
tyres are cold. Tyre Wear Indicators
If it is necessary to check the tyres when they are warm, Tyres fitted as original equipment have wear indicators
you should expect the pressures to have increased by 30～ moulded into the tread pattern at several points around the
40kPa (0.3 ～ 0.4bar). In this circumstance, NEVER let circumference. When the tread has worn down to 1.6mm
air out of the tyres in order to match the recommended the indicators will come to the surface of the tread pattern,
pressures (cold) in the technical data. producing the effect of a continuous band of rubber across
the width of the tyre.
Valves
Keep the valve caps firmly secured to prevent dirt from 6
entering the valve. Check the valve for leaks (listen for a
tell-tale hissing) when you check the tyre pressure.
Punctured Tyres
Your vehicle is fitted with tyres which may not leak if
penetrated by a sharp object, provided the object remains
in the tyre. If you are aware of this occurring, reduce speed
301
MAINTENANCE
Tyre Rotation
It is recommended that you swap wheels from side to side
or front to rear at irregular intervals in order to equalise
tyre wear.
In cases of even front tyre wear, it is recommended to
exchange the front and rear wheels as shown in the figure.
This can equalise tyre wear, extend tyre life, and uniform
tyre fatigue.
Swapping the driven wheels diagonally is not advised,
therefore, on AWD models it is not recommended to
change any wheels diagonally, front to rear change is
permissible. Swapping non driven wheels is allowed,
therefore on 2WD models it is permissible to swap wheels
IMPORTANT
diagonally whilst considering the DOR advice.
A tyre MUST be replaced as soon as a wear indicator
becomes visible. Otherwise there may be a risk of
accidents.
302
MAINTENANCE
to correctly indicate the tyre pressure value at the
corresponding position.
Note: Directional tyres are marked with ‘direction of

rotation' (DOR). To maintain driving characteristics,
tyres must always be fitted with indication arrow 6
showing the correct ‘DOR'. When the tyre tread
pattern is directional, the wheels must not be
exchanged diagonally or left to right but can be
exchanged front to rear.
Note: After any tyre/wheel rotation, the vehicle must

be driven at a speed of 25 mph for about 10 minutes
303
MAINTENANCE
Tyre/Snow Chains Note: If you often drive on snow covered and icy roads,
it is recommended to use winter tyres. Please consult
Unsuitable tyre/snow chains may damage the tyres, wheels,
an MG Authorised Repairer for details.
suspension, brakes or bodywork of your vehicle.
Please pay attention to the following requirements during
usage:
• The tyre/snow chains can only be fitted on the drive
wheels;
• The thickness of tyre/snow chains must not exceed
15mm;
• Please always observe the installation and tension
instructions for the tyre/snow chains, as well as the
speed limits of different roads;
• Do not drive faster than 30 mph;
• To avoid the tyre damage and excessive wear of
the tyre/snow chains, the tyre/snow chains must be
removed while driving on the road without snow.
For this vehicle, the only specification of
wheels and tyres that will support tyre/snow
chains are as follows:
Wheel rim size: 6.5J×16
Tyre size: 205/60 R16
304
MAINTENANCE
Cleaning and Vehicle Care • In hot weather, DO NOT wash the car in direct sunlight.
Observe all safety precautions on cleaning • When using a hose, DO NOT aim the water directly
products; Do Not drink fluids and keep them at window, door or sunroof seals, or through wheel
away from the eyes. apertures onto the brake components.
If the car is particularly dirty, use a hose to flush grime and
grit from the bodywork, prior to washing. Then, wash the
Exterior car using cold or lukewarm water containing a good quality
wash and wax shampoo. Always use plenty of water to
Washing Your Car
ensure that grit is flushed from the surface and not ground
Some high pressure cleaning systems will into the paintwork. After washing, rinse the bodywork
penetrate door, window and sunroof seals, with clean water and dry off with a chamois leather.
and damage lock mechanisms. DO NOT aim
water jets directly at components that might Cleaning the underside
be easily damaged. Ensure the vehicle power
system is OFF when washing your car. Note: DO NOT use a high pressure hose to clean the
Do not clean the front compartment with

front compartment – damage to the car’s electronic 6
systems may occur.
high pressure water since it may damage the
electrical system of the vehicle. From time to time, but particularly during winter months
when salt has been used on the roads, use a hose to wash
In order to preserve the paint finish on your car, please the underside of the car. Flush away accumulations of mud
observe the following care points: and thoroughly clean those areas where debris can easily
• DO NOT use hot water to wash the car. collect (wheel arches and panel seams, for example).
• DO NOT use detergents or washing up liquid.
305
MAINTENANCE
IMPORTANT IMPORTANT
• Avoid cleaning the vehicle in direct sunlight. • Please pay attention to the operating instructions of
• When cleaning the vehicle in winter avoid spraying high pressure cleaner.
water directly onto door locks and panel gaps due • High pressure cleaners should not be closely
to risk of icing. directed at soft parts of the vehicle.
• Do not use rough sponges or cloth to clean the car,
this will damage the paintwork finish. Removing tar spots
• When cleaning the headlamps do not use a dry cloth
Use white spirit to remove tar spots and stubborn grease
or sponge, use only warm soapy water.
stains from the paintwork. Then wash the area immediately
with soapy water to remove all traces of the spirit.
Cleaning with a High Pressure Cleaner
Body Protection
Note: Always read the manufacturers operating
After washing, examine the paintwork for damage. If the
instructions.
damage has revealed bare metal, use a colored primer first,
When using high pressure washers, always ensure there is then apply the correct colour base coat and finish off with
adequate distance between the spray nozzle and any soft a lacquer pencil, if appropriate. Carry out this treatment
materials, decals or rubber seals. after washing but before polishing or waxing. More
Note: DO NOT direct the pressure washer nozzle extensive damage to paint or bodywork must be repaired
directly toward the high voltage charging point or high in accordance with the manufacturer’s recommendations.
voltage battery connections on the underside of the Failure to do this will invalidate the Anti-Corrosion
vehicle. Warranty. If in doubt, ask your MG Authorised Repairer.
306
MAINTENANCE
Polishing the Paintwork Windows and Mirrors
DO NOT use car polish containing coarse Regularly clean all windows, inside and out, using an
abrasives – these will remove the paint film approved glass cleaner.
and damage the gloss finish.
Windscreen: In particular, clean the outside of the screen
Occasionally treat the paint surface with an approved polish with glass cleaner after washing the car with wash and wax
containing the following properties: products, and before fitting new wiper blades.
• Very mild abrasives to remove surface contamination Rear screen: Clean the inside with a soft cloth, using a side
without removing or damaging the paint. to side motion to avoid damaging the heating elements.
• Filling compounds that will fill scratches and reduce
Note: DO NOT scrape or use abrasive cleaners on the
their visibility.
inside of the rear screen – this will damage the heating
• Wax to provide a protective coating between the paint elements.
and the elements.
Note: If possible, avoid applying polish or wax Mirrors: Wash with soapy water. Use a plastic scraper to
products to window glass and rubber seals. remove ice. DO NOT use abrasive cleaning compounds
or metal scraper. 6
Wiper Blades
Plastic Components
Wash in warm soapy water. DO NOT use spirit or solvent
Any plastic components should be cleaned using
based cleaners.
conventional cleaning methods and not be treated with
abrasive materials.
307
MAINTENANCE
Paint Damage Cleaning the Interior
Any paint damage or stonechips should be treated with Plastic materials
suitable paint/lacquer materials immediately to avoid
Clean plastic-faced materials with diluted upholstery
invalidating the Anti Corrosion Warranty.
cleaner, then wipe with a damp cloth.
Weather Strips and Rubber Seals Note: DO NOT polish dashboard components – these
Any weather strips or rubber aperture seals should be should remain non-reflective.
treated with suitable materials (silica gel) if they are cleaned
using strong detergents, this should avoid any sticking and Carpet and fabrics
maintain the service life of the seal. Clean with diluted upholstery cleaner - test a concealed
area first.
Wheels
When cleaning the wheels any materials or Leather
water that contact the brake disc directly Clean leather trim with warm water and a non-detergent
may effect braking efficiency. soap. Dry and polish the leather with a dry, clean, lint-free
cloth.
In order to ensure the wheels are kept in optimum
condition they should be cleaned regularly. Note: DO NOT use petrol, detergents, furniture
creams or polishes as cleaning agents.
Only use a recommended non-acidic propriety wheel
cleaner. Always read the instructions on the product.
308
MAINTENANCE
Instrument Pack, Audio and Navigation Display Extend the belts, then use warm water and a non-detergent
soap to clean. Allow the belts to dry naturally; DO NOT
Clean with a dry cloth only. DO NOT use cleaning fluids
retract them or use the car until they are completely dry.
or sprays.
Airbag Module Covers

DO NOT allow these areas to be flooded with
liquid and DO NOT use petrol, detergent,
furniture cream or polishes.
To protect damage to the airbag SRS, the following

areas should be cleaned sparingly with a damp cloth and
upholstery cleaner ONLY:
• Steering wheel centre pad.
• Area of dashboard containing the passenger airbag.
• Area of roof lining and front pillar finishers which 6
enclose the side head impact protection modules.
Seat Belts
DO NOT use bleaches, dyes or cleaning

solvents on seat belts.
309
Technical Data
312 Technical Data Dimensions
314 Weights
318 Parameters of Traction Motor
319 Recommended Fluids and
Capacities
320 Wheel Alignment (Unladen
Condition)
320 Wheels and Tyres
320 Tyre Pressure (Cold)
7
TECHNICAL DATA
Technical Data Dimensions
E D F
B A
Item, Units Parameters Item, Units Parameters
Overall length A, mm 4323 Rear Overhang F，mm 837

Overall width B, mm 1809
Front Wheel Track，mm 1526
1625(body height)
Overall height C (unladen), mm Rear Wheel Track，mm 1539
1649(with rack)
Wheelbase D，mm 2585 Minimum Turning Diameter，m 11.2
Front Overhang E，mm 901
Note: Vehicle length not including the license plate.
312
TECHNICAL DATA
Note: Rearview mirrors and the deformed portion of
tyre wall directly above the touchdown point are not
included in the total width.
313
TECHNICAL DATA
Weights
Item, Units Parameters
SE(51) Trophy(51) SE & Trophy(72)
Person in cab, person 5
Unladen vehicle weight 1570 1610 1620

(kerb), kg
Gross vehicle weight, kg 2060 2060 2070
Unladen front axle 891 908 914

weight, kg
Unladen rear axle weight, 679 702 706

kg
Gross front axle weight, 1014 1014 1020

kg
Gross rear axle weight, 1046 1046 1050

kg
314
TECHNICAL DATA
Towing Weights
Item, Units Parameters
Towing limit unbraked, kg 500
Towing limit braked, kg 500
Towing hitch load, kg 50

Note: When towing a trailer, the vehicle speed MUST not exceed 60mph.
Note: Prior to towing a trailer, please check the rear tyre pressures, inflate to at least 20kPa (0.2bar) above the
recommended pressure - DO NOT allow the tyre pressure to exceed 300kPa (3.0bar), this can be dangerous.
315
TECHNICAL DATA
Towing Bar Dimensions
A E
D
F
G
B
C
Item Dimension Description, Units Parameters
A Bumper to centre of tow ball, mm 80

B Attachment point to centre the tow ball, mm 57
C Wheel centre to centre of tow ball, mm 912

D Centre of tow ball to side member, mm 465
316
TECHNICAL DATA
Item Dimension Description, Units Parameters
E Distance between side members, mm 930
F Centre of tow ball to centre of first attachment point, mm 321
Centre of tow ball to centre of second attachment point,
G 460
mm
317
TECHNICAL DATA
Parameters of Traction Motor
Parameter Values
Item, Units
Battery Pack Type 1 Battery Pack Type 2
Traction motor type Three-phase permanent magnet synchronous motor
Continuous Power/Maximum Net Power, kW 75/130 73/115
Peak Torque, Nm 280 280
Rated Speed/Maximum Speed, rpm 9000/15000 8000/15000
Winding Type 4
Waterproof Grade IP67
318
TECHNICAL DATA
Recommended Fluids and Capacities
Name Grade Capacity
Electric drive transmission coolant, L 4.8

Glycol (OAT)
High-voltage battery pack coolant, L 5.6
Electric drive transmission oil, L Shell E-Fluids E6 iX (SL2808) 0.9
Brake fluid, L DOT 4 0.85
Windshield detergent, L ZY-Ⅷ 4
Air conditioning refrigerant, g R1234yf 540±20
319
TECHNICAL DATA
Wheel Alignment (Unladen Condition) Tyre Pressure (Cold)
Item Parameter Wheels Unladen
Camber angle -0°35¢±45¢ Front Wheels 280kPa/2.8bar/41psi
Castor angle 4°01¢±45¢ Rear Wheels 280kPa/2.8bar/41psi

Front
Toe-in (Total) 0°8¢±15¢
King pin inclination 12°04¢±45¢
Camber angle -1°15¢±45¢

Rear
Toe-in (Total) 0°24¢±20¢
Wheels and Tyres

Wheel size 7.0J×17
Tyre size 215/55 R17 94V
320
Appendix
322 Removable Tow Bar
8
APPENDIX
Removable Tow Bar The tow ball is in the spring position if:
• The operating handle is pushed in completely and no
Tow Bar Operating Instructions colour indication is shown inside the indication area of
the operating handle.
Safety:
• The slider is pulled fully towards the tow ball (shown in
Operation of the detachable tow bar should only be picture 3.1).
performed by hand, never use hand tools to operate the • It is not possible to lock the system with the supplied
locking mechanism. locking keys (see picture 5.2).
If the trailer is fitted with a security cable or brake cable it The tow ball is NOT in the spring position if:
must be attached to the dedicated connection hole in the • The operating handle is popped out and shows a red
fixed part of the tow bar. field in the indication area of the operating handle (see
When a stabiliser coupling is installed on the trailer never picture 3.1)
use grease on the tow ball. • The slider is pushed out towards the tow ball (the part
is indicated by in picture 3.1).
Always remove the detachable tow ball when not in use if
• It is possible to lock the system with the supplied keys
it obscures the registration plate.
(see picture 5.2).
Preparation: To place the tow ball in the spring position:
• Unlock the tow ball (see picture 6.1)
Remove tow ball cover.
• Push the operating handle inwards, rotate in a clockwise
Ensure the tow ball is clean and free from dirt and debris. direction (whilst pushing inwards) until the handle
Ensure the tow ball is in the ‘spring position’ (see picture remains in position (see picture 3.2). If unsure repeat
3.1). operation.
322
APPENDIX
Note: If a tow ball cannot be tensioned into the spring Attachment:
position it cannot and MUST NOT be used.
Before attaching the tow ball to the car please remove the
cover from the housing (see picture 4.1).
3.1
• Insert tow ball (that must be in the spring position) fully
into the housing.
• Hold the tow ball in position, keeping your hands away
from the operating handle, use a slight force to pull at
GREEN RED RED
the tow ball as shown in picture 4.3.
• The unlocking pin will trigger the locking mechanism and
5mm
the locking process will automatically take place.
3.2
RED • Always check the tow ball is correctly installed, this can
be recognised by:
1 2
• The operating handle pops out and a approximate gap
CLICK
of 5 millimeters will be visible between the tow ball and
the operating handle (see picture 5.1).
• A green field will be visible in the indication area of the
GREEN GREEN
operating handle (see picture 5.1).
• The tow ball can be locked using the supplied keys (see
GREEN GREEN picture 5.2). This can only be done when the handle
has popped out completely, after this the handle can no
4.1
longer be pushed in and the tow ball cannot be released 8
(remember to remove the keys).
323
APPENDIX
• Check the tow ball for security – no play should be
evident.
The tow ball is now ready for use.
4.1 4.2 4.3
324
APPENDIX
Care Points • The tow ball can now be removed from the housing in
• Always check the tow ball for correct mounting every a downward motion (see picture 6.4). WARNING, this
time prior to use. item is heavy, do not allow it to drop.
• Never attempt to attach/detach a tow ball whilst • Refit the plastic cover into the housing (see picture 6.5).
trailer/accessory attached.
5.1
• Always keep the tow ball clean and free from debris, do
GREEN GREEN
not clean with high pressure washer.
RED
• Never use a tow ball that has signs of damage, excessive
wear or modification.
RED
• Never use a tow ball that has been installed by any other
5 mm 5 mm RED
method than ‘hand pressure’.
5.2 5.3
Removal
Always disconnect the trailer/accessory and safety cable
prior to tow ball removal.
• Unlock the detachable tow ball by turning the locking
key clockwise using your thumb and forefinger (see
picture 6.1).
• Hold the tow ball with your left hand, push the
operating handle fully inwards and turn clockwise until
the operating handle remains in position (see picture 8
6.3).
325
APPENDIX
6.1 6.2
6.3 6.4
6.5
326

New MG ZS EV Owner Manual

Uploaded by

Copyright:

Available Formats

New MG ZS EV Owner Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

New MG ZS EV Owner Manual

Uploaded by

Copyright:

Available Formats

CONTENTS

Status at Time of Printing

Identifies components being explained.

Note: This describes helpful information.

Remember the breakdown safety code

• On the inner side of the tailgate visible by opening the

Note: The DLC is located in the driver footwell at the

1 Vehicle Identification Number (VIN) Drive Motor Number

1 High Voltage Battery (ESS)

1 Speedometer value, it represents that the power system outputs

Main Beam Indicator The headlamp high beam is turned on.

Auto Main Beam

Side Lamp Indicator The side lamps are on.

Auto Hold Status

The ABS has failed.

Driving Power Limited

The vehicle has a fault and its performance is limited.

READY Indicator The vehicle is ready for driving.

Displays the current driving mode of the vehicle: NORMAL、SPORT、

The Manual Speed Assist System is activated.

The Intelligent Speed Assist System is activated.

Manual Speed Assist NNN

Speed Limit Sign

The Adaptive Cruise Control System is activated.

The Adaptive Cruise Control System has a fault.

The Traffic Jam Assist System is activated.

The lane departure warning function is on and meets the activation

The system is ready and an emergency services call (eCall) is in progress.

The system is still capable of sending out a vehicle information message to

The eCall system has failed and not operational.

0 Driver, or driver & front passenger.

1 All the seats occupied with no load.

All the seats occupied plus an evenly

Driver only, plus an evenly distributed load in

Position 0 is the initial position of the headlamp levelling

Headlamp High/Low Beam Switching

Hazard Warning Lamp

Fast Wipe Programmed Wash/Wipe

The rear window wiper and washer will only operate

Wash and Wipe

Electric Power Steering

The electric power steering system only works when the

To adjust the angle of the steering column to suit your

To avoid possible SRS issues, please do not press with

Press the horn button area on the steering wheel (as

Exterior Door Mirrors

• The mirror adjustment function will work with the

Manual Anti-dazzle Interior Rearview Mirror

Improper use or activation of the electric

Safety of the vehicle occupants must be

• Avoid fully opening the sunroof during rain showers.

This will ensure no debris or foreign objects

12V, and the maximum power of 120 Watt,

Rear USB Ports Top USB Port

The wireless charging function for a mobile phone is

The wireless charging area is located in the area shown

Lift the armrest (arrowed) to open the compartment cover.

The rear parcel shelf is connected to the tailgate using

Centre Console Cup Holder

The centre console cup holder is situated at the front end