Repair Manual: M452nw M452dn M452dw

Color LaserJet Pro MFP M377
Color LaserJet Pro M452

Color LaserJet Pro MFP M477
Repair Manual
M452nw M452dw
M452dn
M377dw
M477fnw
M477fnw
M477fdw
www.hp.com/support/colorljM377MFP
www.hp.com/support/colorlj452
www.hp.com/support/colorlj477MFP
For printer theory and problem soloving
information, see the Troubleshooting Manual.
HP Color LaserJet Pro MFP M377, HP Color
LaserJet Pro M452 and HP Color LaserJet
Pro MFP M477
Repair Manual
Copyright and License
© Copyright 2016 HP Development Company,

L.P.
Reproduction, adaptation, or translation

without prior written permission is prohibited,
except as allowed under the copyright laws.
The information contained herein is subject to

change without notice.
The only warranties for HP products and

services are set forth in the express warranty
statements accompanying such products and
services. Nothing herein should be construed
as constituting an additional warranty. HP shall
not be liable for technical or editorial errors or
omissions contained herein.
Edition 3, 4/2016
Conventions used in this guide
TIP: Helpful hints or shortcuts.
NOTE: Information that explains a concept or how to complete a task.
Reinstallation tip: Reinstallation helpful hints, shortcuts, or considerations.
IMPORTANT: Information that help the user to avoid potential printer error conditions.
CAUTION: Procedures that the user must follow to avoid losing data or damaging the printer.
WARNING! Procedures that the user must follow to avoid personal injury, catastrophic loss of data, or
extensive damage to the printer.
ENWW iii
iv Conventions used in this guide ENWW
For additional service and support information
HP service personnel, go to the Service Access Work Bench (SAW) at http://h41302.www4.hp.com/km/saw/
home.do.
Channel partners, go to HP Channel Services Network (CNS) at https://h30125.www3.hp.com/hpcsn.
At these locations, find information on the following topics:
● Install and configure
● Printer specifications
● Up-to-date control panel message (CPMD) troubleshooting
● Solutions for printer issues and emerging issues
● Remove and replace part instructions and videos
● Service advisories
● Warranty and regulatory information
To access HP PartSurfer information from any mobile device, go to http://partsurfermobile.hp.com/ or scan

the Quick Response (QR) code below.
ENWW v
vi For additional service and support information ENWW
Table of contents
1 Removal and replacement .............................................................................................................................. 1

For additional service and support ........................................................................................................................ 2
Removal and replacement strategy ...................................................................................................................... 3
Introduction ......................................................................................................................................... 3
Considerations during removal and replacement .............................................................................. 3
Electrostatic discharge ........................................................................................................................ 4
Required tools ..................................................................................................................................... 4
Fasteners used in this printer .............................................................................................................. 5
Service approach .................................................................................................................................................... 6
Before performing service .................................................................................................................. 6
Secondary service menu ..................................................................................................................... 6
After performing service ..................................................................................................................... 6
Post service tests ................................................................................................................................ 7
Print-quality test ............................................................................................................... 7
Copy-quality test (M377, M477 models) .......................................................................... 7
Fax-quality test (M477 models) ....................................................................................... 7
Order parts by authorized service providers ......................................................................................................... 8
Orderable parts .................................................................................................................................... 8
Whole unit replacement (WUR) part numbers .................................................................................... 8
Supplies part numbers ........................................................................................................................ 9
Related documentation and software ................................................................................................ 9
Removal and replacement procedures ............................................................................................................... 11
Customer self-repair (CSR) A parts and assemblies ......................................................................... 11
Removal and replacement: Toner cartridges ................................................................. 12
Removal and replacement: Trays ................................................................................... 18
Removal and replacement: Tray 2 ............................................................... 19
Removal and replacement: Tray 3 ............................................................... 21
Field replaceable units (FRUs) ........................................................................................................... 23
Removal and replacement: Rollers ................................................................................. 23
Removal and replacement: Tray 1 pickup roller .......................................... 24
Removal and replacement: Tray 1 separation pad ...................................... 29
Removal and replacement: Tray 2 pickup and feed rollers ......................... 34
ENWW vii
Removal and replacement: Tray 2 separation roller ................................... 47
Removal and replacement: Tray 3 pickup and feed rollers ......................... 59
Removal and replacement: Tray 3 separation roller ................................... 66
Removal and replacement: Secondary transfer roller ................................. 72
Removal and replacement: External panels, covers, and doors .................................... 78
Removal and replacement: Right cover (M452 models) .............................. 79
Removal and replacement: Left cover (M452 models) ................................ 94
Removal and replacement: Right cover (M377, M477 models) ................ 109
Removal and replacement: Left cover (M377, M477 models) ................... 127
Removal and replacement: Front door assembly ...................................... 146
Removal and replacement: Duplexer door assembly (duplex models) .... 180
Removal and replacement: Rear top cover (simplex models) ................... 227
Removal and replacement: Rear lower cover (simplex models) ............... 272
Removal and replacement: Rear door (simplex models) .......................... 317
Removal and replacement: Top cover (M452 models) .............................. 364
Removal and replacement: Top cover (M377, M477 models) ................... 405
Removal and replacement: Touchscreen control panel (M452dw
model) ........................................................................................................ 470
Removal and replacement: Touchscreen control panel (M377, M477
models) ....................................................................................................... 507
Removal and replacement: Integrated scanner assembly (M377, M477 models) ...... 569
Introduction ................................................................................................ 569
Step 1: Remove Tray 2 ................................................................................ 569
Step 2: Open the front door and rear door or duplexer door .................... 570
Step 3: Remove the left cover (M377, M477 models) ................................ 572
Step 4: Remove the integrated scanner assembly .................................... 576
Step 5: Unpack the replacement part ........................................................ 581
Step 6: Install the integrated scanner assembly ....................................... 581
Step 7: Install the left cover (M377, M477 models) ................................... 586
Step 8: Close the front door and rear door or duplexer door .................... 592
Step 9: Install Tray 2 ................................................................................... 593
Removal and replacement: Internal parts and assemblies ......................................... 595
Removal and replacement: Power switch assembly ................................. 597
Removal and replacement: Toner cartridge tray ....................................... 626
Removal and replacement: Cartridge fan .................................................. 660
Removal and replacement: Power supply fan ........................................... 689
Removal and replacement: Low-voltage power supply (LVPS) ................. 719
Removal and replacement: Pickup motor .................................................. 778
Removal and replacement: Driver PCA ...................................................... 839
Removal and replacement: Drum motor ................................................... 869
Removal and replacement: Developer motor ............................................ 936
viii ENWW
Removal and replacement: Secondary transfer assembly (simplex
models) ..................................................................................................... 1003
Removal and replacement: Secondary transfer assembly (duplex
models) ..................................................................................................... 1009
Removal and replacement: Intermediate transfer belt (ITB) .................. 1016
Removal and replacement: Registration density sensor ........................ 1082
Removal and replacement: Re-pickup assembly (duplex models) ......... 1166
Removal and replacement: Engine controller PCA .................................. 1222
Removal and replacement: Lifter drive assembly ................................... 1251
Removal and replacement: Pickup assembly .......................................... 1321
Removal and replacement: Front feed guide assembly .......................... 1411
Removal and replacement: Rear feed guide assembly ........................... 1508
Removal and replacement: Registration assembly ................................. 1606
Removal and replacement: Memory PCA ................................................. 1708
Removal and replacement: Laser scanner (M452 models) ..................... 1795
Removal and replacement: Laser scanner ( M377, M477 models) ......... 1855
Removal and replacement: Fuser (simplex models) ............................... 1939
Removal and replacement: Fuser (duplex models) ................................. 2027
Removal and replacement: Fuser power supply ..................................... 2116
Removal and replacement: Fuser motor ................................................. 2148
Removal and replacement: Duplex drive assembly (duplex models) ..... 2181
Removal and replacement: Wireless antenna (M452nw/dw models) ..... 2278
Removal and replacement: Wireless PCA (M452nw/dw models) ............ 2317
Removal and replacement: Wireless PCA (M377, M477fnw/fdw
models) ..................................................................................................... 2336
Removal and replacement: Formatter PCA ............................................. 2361
Removal and replacement: Environmental sensor ................................. 2393
Removal and replacement: Fax PCA (M477 models) ............................... 2420
Removal and replacement: NFC PCA (M452dw and M477dw models) ... 2460
Removal and replacement: Walk-up USB port (M452dw model) ............ 2544
Removal and replacement: Walk-up USB port (M377, M477 models) .... 2577
Removal and replacement: Drawer connector ........................................ 2639
Removal and replacement: Accessories ..................................................................... 2665
550-sheet paper feeder ........................................................................... 2666
2 Parts and diagrams .................................................................................................................................. 2985

For additional service and support ................................................................................................................. 2986
Assembly locations ......................................................................................................................................... 2987
Base printer, M452 ........................................................................................................................ 2987
Base printer, M377 and M477 ....................................................................................................... 2988
550-sheet paper feeder (all models) ............................................................................................ 2989
ENWW ix
Order parts, accessories, and supplies ........................................................................................................... 2990
Ordering ........................................................................................................................................ 2990
Orderable parts ............................................................................................................................. 2990
Supplies ......................................................................................................................................... 2990
Accessories .................................................................................................................................... 2991
Customer self-repair kits .............................................................................................................. 2991
Related documentation and software .......................................................................................... 2991
How to use the parts lists and diagrams ........................................................................................................ 2992
Parts and diagrams: Document feeder and scanner whole units .................................................................. 2994
Document feeder and scanner (M377, M477) .............................................................................. 2994
Parts and diagrams: Covers and control panels ............................................................................................. 2996
M452 covers and control panels ................................................................................................... 2996
M377, M477 covers and control panel ......................................................................................... 2998
Parts and diagrams: Internal components ..................................................................................................... 3000
Internal components (1 of 5) ........................................................................................................ 3000
Parts and diagrams: 550-sheet paper feeder ................................................................................................ 3010
550-sheet paper feeder covers .................................................................................................... 3010
550-sheet paper feeder main body (1 of 2) ................................................................................. 3012
550-sheet paper feeder main body (2 of 2) ................................................................................. 3014
Alphabetical parts list ..................................................................................................................................... 3016
Numerical parts list ......................................................................................................................................... 3023
Index .......................................................................................................................................................... 3031
x ENWW
List of tables
Table 1-1 Supplies part numbers ......................................................................................................................................... 9

Table 2-1 Base printer, M452 (no optional trays or accessories) .................................................................................. 2987
Table 2-2 Base printer, M377, M477 (no optional trays or accessories) ....................................................................... 2988
Table 2-3 550-sheet paper feeder (all models) ............................................................................................................. 2989
Table 2-4 Supplies .......................................................................................................................................................... 2990
Table 2-5 Accessories ..................................................................................................................................................... 2991
Table 2-6 Document feeder and scanner (M377, M477) ............................................................................................... 2995
Table 2-7 M452 covers and control panels .................................................................................................................... 2997
Table 2-8 M377, M477 covers and control panel ........................................................................................................... 2999
Table 2-9 Internal components (1 of 5) ......................................................................................................................... 3001
Table 2-10 Internal components (2 of 5) ....................................................................................................................... 3003
Table 2-14 550-sheet paper feeder covers ................................................................................................................... 3011
Table 2-15 550-sheet paper feeder main body (1 of 2) ................................................................................................ 3013
Table 2-16 550-sheet paper feeder main body (2 of 2) ................................................................................................ 3015
ENWW xi
xii ENWW
List of figures
Figure 1-1 Screwdrivers ........................................................................................................................................................ 4

Figure 1-2 Open the front door .......................................................................................................................................... 13
Figure 1-3 Open the cartridge drawer ................................................................................................................................ 13
Figure 1-4 Remove the toner cartridge .............................................................................................................................. 14
Figure 1-5 Recycle and unpack ........................................................................................................................................... 14
Figure 1-6 Rock the toner cartridge ................................................................................................................................... 15
Figure 1-7 Do not touch imaging drum .............................................................................................................................. 15
Figure 1-8 Install a toner cartridge .................................................................................................................................... 16
Figure 1-9 Close the toner cartridge drawer ...................................................................................................................... 16
Figure 1-10 Close the front door ........................................................................................................................................ 17
Figure 1-11 Remove the tray .............................................................................................................................................. 19
Figure 1-12 Recycle and unpack ......................................................................................................................................... 20
Figure 1-13 Install the tray ................................................................................................................................................. 20
Figure 1-17 Release the front door .................................................................................................................................... 25
Figure 1-18 Open the front door ........................................................................................................................................ 25
Figure 1-19 Release two tabs ............................................................................................................................................. 26
Figure 1-20 Remove the pickup roller ................................................................................................................................ 26
Figure 1-22 Install the pickup roller ................................................................................................................................... 27
Figure 1-24 Release the front door .................................................................................................................................... 30
Figure 1-26 Press down and release tabs .......................................................................................................................... 31
Figure 1-27 Remove the separation pad ............................................................................................................................ 31
Figure 1-29 Position the separation pad ............................................................................................................................ 32
Figure 1-30 Snap the separation pad into place ................................................................................................................ 33
ENWW xiii
Figure 1-33 Open the cartridge drawer .............................................................................................................................. 35
Figure 1-34 Remove the toner cartridge ............................................................................................................................ 36
Figure 1-35 Slide the cartridge tray in ............................................................................................................................... 36
Figure 1-38 Release the feed guide ................................................................................................................................... 38
Figure 1-39 Release the roller holder ................................................................................................................................. 38
Figure 1-40 Remove the roller case ................................................................................................................................... 39
Figure 1-41 Locate the rollers ............................................................................................................................................ 39
Figure 1-42 Remove the roller ............................................................................................................................................ 40
Figure 1-44 Position the roller ........................................................................................................................................... 41
Figure 1-45 Install the roller ............................................................................................................................................... 41
Figure 1-46 Position the roller case ................................................................................................................................... 42
Figure 1-47 Install the roller case ...................................................................................................................................... 42
Figure 1-50 Slide the cartridge tray out ............................................................................................................................. 44
Figure 1-51 Do not touch imaging drum ............................................................................................................................ 44
Figure 1-52 Install a toner cartridge .................................................................................................................................. 45
Figure 1-53 Close the toner cartridge drawer .................................................................................................................... 45
Figure 1-56 Open the cartridge drawer .............................................................................................................................. 48
Figure 1-57 Remove the toner cartridge ............................................................................................................................ 49
Figure 1-58 Slide the cartridge tray in ............................................................................................................................... 49
Figure 1-61 Release the tabs .............................................................................................................................................. 51
Figure 1-62 Remove the cover ........................................................................................................................................... 51
Figure 1-63 Release the separation roller .......................................................................................................................... 52
Figure 1-64 Remove the separation roller ......................................................................................................................... 52
Figure 1-66 Install the separation roller ............................................................................................................................ 53
Figure 1-67 Position the roller cover .................................................................................................................................. 54
Figure 1-71 Slide the cartridge tray out ............................................................................................................................. 56
Figure 1-72 Do not touch imaging drum ............................................................................................................................ 56
Figure 1-73 Install a toner cartridge .................................................................................................................................. 57
xiv ENWW
Figure 1-74 Close the toner cartridge drawer .................................................................................................................... 57
Figure 1-77 Release the roller holder ................................................................................................................................. 60
Figure 1-78 Remove the roller case ................................................................................................................................... 61
Figure 1-79 Locate the rollers ............................................................................................................................................ 61
Figure 1-80 Remove the roller ............................................................................................................................................ 62
Figure 1-82 Position the roller ........................................................................................................................................... 63
Figure 1-83 Install the roller ............................................................................................................................................... 63
Figure 1-84 Position the roller case ................................................................................................................................... 64
Figure 1-85 Install the roller case ...................................................................................................................................... 64
Figure 1-88 Release the tabs .............................................................................................................................................. 67
Figure 1-89 Remove the cover ........................................................................................................................................... 68
Figure 1-90 Release the separation roller .......................................................................................................................... 68
Figure 1-91 Remove the separation roller ......................................................................................................................... 69
Figure 1-93 Install the separation roller ............................................................................................................................ 70
Figure 1-94 Position the roller cover .................................................................................................................................. 70
Figure 1-98 Lift the end of the roller .................................................................................................................................. 73
Figure 1-99 Remove the stopper ........................................................................................................................................ 74
Figure 1-100 Reattach the stopper spring ......................................................................................................................... 74
Figure 1-101 Remove the secondary transfer roller .......................................................................................................... 75
Figure 1-102 Recycle and unpack ...................................................................................................................................... 75
Figure 1-103 Position the secondary transfer roller ......................................................................................................... 76
Figure 1-104 Attach stopper .............................................................................................................................................. 76
Figure 1-105 Install the secondary transfer roller ............................................................................................................. 77
Figure 1-106 Check the tabs ............................................................................................................................................... 77
Figure 1-107 Remove the tray ............................................................................................................................................ 80
Figure 1-108 Release the front door .................................................................................................................................. 80
Figure 1-109 Open the front door ...................................................................................................................................... 81
Figure 1-110 Open the duplexer door ................................................................................................................................ 81
Figure 1-111 Open the rear door ........................................................................................................................................ 82
Figure 1-112 Remove one screw ........................................................................................................................................ 82
Figure 1-114 Locate the tabs ............................................................................................................................................. 83
ENWW xv
Figure 1-115 Release front lower tabs ............................................................................................................................... 84
Figure 1-116 Release lower rear tab .................................................................................................................................. 84
Figure 1-117 Release two front tabs .................................................................................................................................. 85
Figure 1-118 Release upper tabs ....................................................................................................................................... 85
Figure 1-119 Remove the right cover ................................................................................................................................. 86
Figure 1-120 Recycle and unpack ...................................................................................................................................... 86
Figure 1-121 Position two tabs .......................................................................................................................................... 87
Figure 1-122 Install rear tab ............................................................................................................................................... 87
Figure 1-123 Install the right cover .................................................................................................................................... 88
Figure 1-124 Install upper tabs .......................................................................................................................................... 88
Figure 1-125 Install the front tabs ..................................................................................................................................... 89
Figure 1-126 Install the front lower tab ............................................................................................................................. 89
Figure 1-127 Install two tabs ............................................................................................................................................. 90
Figure 1-128 Install one screw ........................................................................................................................................... 90
Figure 1-129 Install one screw ........................................................................................................................................... 91
Figure 1-130 Close the front door ...................................................................................................................................... 91
Figure 1-131 Close the duplexer door ................................................................................................................................ 92
Figure 1-132 Close the rear door ........................................................................................................................................ 92
Figure 1-133 Install the tray ............................................................................................................................................... 93
Figure 1-134 Remove the tray ............................................................................................................................................ 95
Figure 1-135 Release the front door .................................................................................................................................. 95
Figure 1-136 Open the front door ...................................................................................................................................... 96
Figure 1-137 Open the duplexer door ................................................................................................................................ 96
Figure 1-138 Open the rear door ........................................................................................................................................ 97
Figure 1-140 Release two tabs ........................................................................................................................................... 98
Figure 1-141 Locate the tabs ............................................................................................................................................. 98
Figure 1-142 Release bottom tabs ..................................................................................................................................... 99
Figure 1-143 Release three tabs ........................................................................................................................................ 99
Figure 1-144 Release two tabs ........................................................................................................................................ 100
Figure 1-145 Remove the button ..................................................................................................................................... 100
Figure 1-146 Recycle and unpack .................................................................................................................................... 101
Figure 1-147 Install the button ........................................................................................................................................ 101
Figure 1-148 Install two tabs ........................................................................................................................................... 102
Figure 1-149 Position three tabs ..................................................................................................................................... 102
Figure 1-150 Install one tab ............................................................................................................................................. 103
Figure 1-151 Install the left cover .................................................................................................................................... 104
Figure 1-152 Make sure the tab does not get caught ...................................................................................................... 104
Figure 1-153 Install four tabs ........................................................................................................................................... 105
Figure 1-154 Engage two tabs ......................................................................................................................................... 105
Figure 1-155 Install hinge pin .......................................................................................................................................... 106
xvi ENWW
Figure 1-156 Install one screw ......................................................................................................................................... 106
Figure 1-157 Close the front door .................................................................................................................................... 107
Figure 1-158 Close the duplexer door .............................................................................................................................. 107
Figure 1-159 Close the rear door ..................................................................................................................................... 108
Figure 1-160 Install the tray ............................................................................................................................................. 108
Figure 1-161 Remove the tray ......................................................................................................................................... 110
Figure 1-162 Release the front door ................................................................................................................................ 110
Figure 1-163 Open the front door .................................................................................................................................... 111
Figure 1-164 Open the duplexer door .............................................................................................................................. 111
Figure 1-165 Open the rear door ...................................................................................................................................... 112
Figure 1-166 Raise the scanner ....................................................................................................................................... 112
Figure 1-167 Remove one screw ...................................................................................................................................... 113
Figure 1-169 Locate the tabs ........................................................................................................................................... 114
Figure 1-170 Release front lower tabs ............................................................................................................................ 114
Figure 1-171 Release lower rear tab ................................................................................................................................ 115
Figure 1-172 Release front upper tabs ............................................................................................................................ 115
Figure 1-173 Rotate the front of the cover ...................................................................................................................... 116
Figure 1-174 Release top tabs ......................................................................................................................................... 116
Figure 1-175 Release one tab and one hook ................................................................................................................... 117
Figure 1-176 Lower the scanner ...................................................................................................................................... 117
Figure 1-177 Remove the right cover .............................................................................................................................. 118
Figure 1-179 Install rear tab ............................................................................................................................................ 119
Figure 1-181 Rotate the right cover ................................................................................................................................. 120
Figure 1-182 Position the hooks in the slots ................................................................................................................... 120
Figure 1-183 Slide the cover ............................................................................................................................................ 121
Figure 1-186 Install the front and lower tabs .................................................................................................................. 122
ENWW xvii
Figure 1-203 Release four tabs ........................................................................................................................................ 132
Figure 1-204 Rotate the cover ......................................................................................................................................... 133
Figure 1-205 Release one tab and two hooks ................................................................................................................. 133
Figure 1-207 Remove the left cover ................................................................................................................................. 134
Figure 1-209 Remove the button ..................................................................................................................................... 135
Figure 1-211 Install the button ........................................................................................................................................ 136
Figure 1-214 Rotate the left cover ................................................................................................................................... 138
Figure 1-218 Install the top hooks ................................................................................................................................... 140
xviii ENWW
Figure 1-239 Release two front tabs ............................................................................................................................... 152
Figure 1-240 Release upper tabs ..................................................................................................................................... 152
Figure 1-255 Tilt the door up ........................................................................................................................................... 160
Figure 1-256 Release the right hinge cover ..................................................................................................................... 160
Figure 1-257 Release one tab .......................................................................................................................................... 161
Figure 1-258 Release the left hinge cover ....................................................................................................................... 161
Figure 1-260 Release one arm ......................................................................................................................................... 162
Figure 1-261 Remove the front door ............................................................................................................................... 163
Figure 1-263 Install the front door .................................................................................................................................. 164
Figure 1-264 Install one arm ............................................................................................................................................ 164
Figure 1-266 Attach left hinge cover ................................................................................................................................ 165
Figure 1-267 Install the left hinge cover .......................................................................................................................... 166
Figure 1-268 Attach right hinge cover ............................................................................................................................. 166
Figure 1-269 Install the hinge cover ................................................................................................................................ 167
Figure 1-271 Position two tabs ........................................................................................................................................ 168
Figure 1-273 Install the right cover .................................................................................................................................. 169
Figure 1-274 Install upper tabs ........................................................................................................................................ 169
Figure 1-275 Install the front tabs ................................................................................................................................... 170
Figure 1-276 Install the front lower tab ........................................................................................................................... 170
ENWW xix
xx ENWW
Figure 1-322 Release bottom tabs ................................................................................................................................... 194
Figure 1-323 Release three tabs ...................................................................................................................................... 195
Figure 1-333 Close the secondary transfer assembly ..................................................................................................... 200
Figure 1-334 Remove three screws ................................................................................................................................. 200
Figure 1-335 Release the retention arm .......................................................................................................................... 201
Figure 1-336 Remove the duplexer door ......................................................................................................................... 201
Figure 1-338 Position the tab in the slot ......................................................................................................................... 202
Figure 1-339 Install the duplexer door ............................................................................................................................ 203
Figure 1-340 Install the retaining arm ............................................................................................................................. 203
Figure 1-341 Install three screws ..................................................................................................................................... 204
ENWW xxi
xxii ENWW
Figure 1-423 Release six tabs .......................................................................................................................................... 247
Figure 1-424 Remove the rear top cover ......................................................................................................................... 247
Figure 1-426 Install the rear top cover ............................................................................................................................ 248
ENWW xxiii
xxiv ENWW
Figure 1-510 Remove two screws and release one tab ................................................................................................... 292
Figure 1-511 Remove the rear lower cover ...................................................................................................................... 293
Figure 1-513 Install the rear lower cover ......................................................................................................................... 294
Figure 1-514 Engage tab and install screws .................................................................................................................... 294
ENWW xxv
xxvi ENWW
Figure 1-598 Remove the rear lower cover ...................................................................................................................... 338
Figure 1-599 Remove the rear door ................................................................................................................................. 339
Figure 1-601 Install the rear door .................................................................................................................................... 340
Figure 1-602 Install the rear lower cover ......................................................................................................................... 340
ENWW xxvii
xxviii ENWW
Figure 1-667 Disconnect one connector .......................................................................................................................... 375
Figure 1-669 Disconnect the antenna .............................................................................................................................. 376
Figure 1-670 Remove two screws .................................................................................................................................... 377
Figure 1-671 Remove the guide ....................................................................................................................................... 377
Figure 1-674 Remove screw and release two tabs .......................................................................................................... 379
Figure 1-676 Remove the top cover ................................................................................................................................. 380
Figure 1-677 Remove three screws and unroute cable ................................................................................................... 380
Figure 1-678 Remove the bracket .................................................................................................................................... 381
Figure 1-679 Rotate the control panel ............................................................................................................................. 381
Figure 1-680 Remove the control panel .......................................................................................................................... 382
Figure 1-682 Set the control panel in place ..................................................................................................................... 383
Figure 1-683 Install the bracket ....................................................................................................................................... 383
Figure 1-684 Install three screws and fasten the cable .................................................................................................. 384
Figure 1-685 Remove protective backing from adhesive strip ....................................................................................... 384
Figure 1-686 Install the top adhesive strip ...................................................................................................................... 385
Figure 1-687 Peel the silver tape up ................................................................................................................................ 385
Figure 1-688 Remove the protective backing .................................................................................................................. 386
ENWW xxix
Figure 1-689 Press the silver tape ................................................................................................................................... 386
Figure 1-690 Position the tape ........................................................................................................................................ 387
Figure 1-691 Remove the protective cover ...................................................................................................................... 387
Figure 1-692 Position the top cover ................................................................................................................................. 388
Figure 1-694 Install two tabs and one screw ................................................................................................................... 389
Figure 1-697 Install the guide .......................................................................................................................................... 390
Figure 1-698 Install two screws ....................................................................................................................................... 391
Figure 1-699 Connect one connector ............................................................................................................................... 391
Figure 1-701 Connect the antenna ................................................................................................................................... 392
xxx ENWW
Figure 1-753 Disconnect the scanner cables ................................................................................................................... 420
Figure 1-754 Remove one screw and release the ground wire ....................................................................................... 421
Figure 1-756 Release the scanner arm pin ...................................................................................................................... 422
Figure 1-757 Remove the scanner arm pin. ..................................................................................................................... 422
Figure 1-759 Remove the scanner cable cover ................................................................................................................ 423
Figure 1-760 Release the cables ...................................................................................................................................... 424
Figure 1-761 Remove the scanner assembly ................................................................................................................... 424
Figure 1-762 Disconnect one connector and remove four screws .................................................................................. 425
Figure 1-763 Remove the fax cover ................................................................................................................................. 425
Figure 1-764 Remove the fax PCA .................................................................................................................................... 426
Figure 1-765 Disconnect two connectors ........................................................................................................................ 426
Figure 1-766 Remove one screw and the sheet metal plate ........................................................................................... 427
Figure 1-767 Lower the support arm and remove one screw ......................................................................................... 427
Figure 1-768 Remove the scanner support arm .............................................................................................................. 428
Figure 1-770 Release the control panel cover ................................................................................................................. 429
ENWW xxxi
Figure 1-771 Remove the control panel cover ................................................................................................................. 429
Figure 1-772 Release the flat cable ................................................................................................................................. 430
Figure 1-775 Refasten the control panel to the top cover .............................................................................................. 431
Figure 1-776 Release the USB cable ................................................................................................................................ 432
Figure 1-778 Release one retainer and three tabs .......................................................................................................... 433
Figure 1-780 Remove the flat cable from the guides ...................................................................................................... 434
Figure 1-784 Slide the walk-up USB port ......................................................................................................................... 436
Figure 1-785 Remove the walk-up USB port ................................................................................................................... 436
Figure 1-787 Connect the walk-up USB port ................................................................................................................... 437
Figure 1-788 Install the walk-up USB port ....................................................................................................................... 438
Figure 1-790 Install the flat cable .................................................................................................................................... 439
Figure 1-792 Route the flat cable .................................................................................................................................... 440
Figure 1-794 Install one retainer and three tabs ............................................................................................................. 441
Figure 1-796 Install the USB cable ................................................................................................................................... 442
Figure 1-801 Install the control panel cover .................................................................................................................... 444
Figure 1-804 Install the scanner support arm ................................................................................................................. 446
Figure 1-805 Raise the metal plate .................................................................................................................................. 446
Figure 1-806 Lower the support arm and install one screw ............................................................................................ 447
Figure 1-807 Install the metal plate ................................................................................................................................ 447
Figure 1-809 Connect two connectors ............................................................................................................................. 448
Figure 1-810 Install the fax PCA ....................................................................................................................................... 449
Figure 1-811 Install the fax cover .................................................................................................................................... 449
xxxii ENWW
Figure 1-812 Install four screws and connect one connector ......................................................................................... 450
Figure 1-813 Install the scanner assembly ...................................................................................................................... 450
Figure 1-814 Press the cables .......................................................................................................................................... 451
Figure 1-815 Position the scanner cable cover ................................................................................................................ 451
Figure 1-816 Install the scanner cable cover ................................................................................................................... 452
Figure 1-817 Install the scanner arm pin ......................................................................................................................... 452
Figure 1-818 Secure the scanner arm pin ........................................................................................................................ 453
Figure 1-820 Install the ground wire ................................................................................................................................ 454
Figure 1-821 Install the M377, M477 scanner ................................................................................................................. 454
ENWW xxxiii
Figure 1-873 Disconnect the antenna .............................................................................................................................. 482
Figure 1-875 Remove the guide ....................................................................................................................................... 483
Figure 1-878 Remove screw and release two tabs .......................................................................................................... 484
Figure 1-881 Remove three screws and unroute cable ................................................................................................... 486
Figure 1-882 Remove the bracket .................................................................................................................................... 486
Figure 1-883 Rotate the control panel ............................................................................................................................. 487
Figure 1-886 Set the control panel in place ..................................................................................................................... 488
Figure 1-887 Install the bracket ....................................................................................................................................... 489
Figure 1-888 Install three screws and fasten the cable .................................................................................................. 489
Figure 1-891 Install two tabs and one screw ................................................................................................................... 491
xxxiv ENWW
Figure 1-894 Install the guide .......................................................................................................................................... 492
Figure 1-898 Connect the antenna ................................................................................................................................... 494
ENWW xxxv
Figure 1-950 Disconnect the scanner cables ................................................................................................................... 522
Figure 1-951 Remove one screw and release the ground wire ....................................................................................... 523
Figure 1-953 Release the scanner arm pin ...................................................................................................................... 524
Figure 1-954 Remove the scanner arm pin. ..................................................................................................................... 524
Figure 1-956 Remove the scanner cable cover ................................................................................................................ 525
Figure 1-957 Release the cables ...................................................................................................................................... 526
Figure 1-958 Remove the scanner assembly ................................................................................................................... 526
Figure 1-959 Disconnect one connector and remove four screws .................................................................................. 527
Figure 1-960 Remove the fax cover ................................................................................................................................. 527
Figure 1-961 Remove the fax PCA .................................................................................................................................... 528
Figure 1-962 Disconnect two connectors ........................................................................................................................ 528
Figure 1-963 Remove one screw and the sheet metal plate ........................................................................................... 529
Figure 1-964 Lower the support arm and remove one screw ......................................................................................... 529
Figure 1-965 Remove the scanner support arm .............................................................................................................. 530
Figure 1-967 Release the control panel cover ................................................................................................................. 531
Figure 1-968 Remove the control panel cover ................................................................................................................. 531
Figure 1-969 Release the flat cable ................................................................................................................................. 532
Figure 1-972 Refasten the control panel to the top cover .............................................................................................. 533
Figure 1-973 Release the USB cable ................................................................................................................................ 534
Figure 1-975 Release one retainer and three tabs .......................................................................................................... 535
xxxvi ENWW
Figure 1-977 Remove the flat cable from the guides ...................................................................................................... 536
Figure 1-983 Route the flat cable .................................................................................................................................... 539
Figure 1-985 Install one retainer and three tabs ............................................................................................................. 540
Figure 1-987 Install the USB cable ................................................................................................................................... 541
Figure 1-992 Install the control panel cover .................................................................................................................... 543
Figure 1-995 Install the scanner support arm ................................................................................................................. 545
Figure 1-996 Raise the metal plate .................................................................................................................................. 545
Figure 1-997 Lower the support arm and install one screw ............................................................................................ 546
Figure 1-998 Install the metal plate ................................................................................................................................ 546
Figure 1-1000 Connect two connectors ........................................................................................................................... 547
Figure 1-1001 Install the fax PCA ..................................................................................................................................... 548
Figure 1-1002 Install the fax cover .................................................................................................................................. 548
Figure 1-1003 Install four screws and connect one connector ....................................................................................... 549
Figure 1-1004 Install the scanner assembly .................................................................................................................... 549
Figure 1-1005 Press the cables ........................................................................................................................................ 550
Figure 1-1006 Position the scanner cable cover ............................................................................................................. 550
Figure 1-1007 Install the scanner cable cover ................................................................................................................. 551
Figure 1-1008 Install the scanner arm pin ....................................................................................................................... 551
Figure 1-1009 Secure the scanner arm pin ...................................................................................................................... 552
Figure 1-1010 Lower the scanner .................................................................................................................................... 552
Figure 1-1011 Install the ground wire ............................................................................................................................. 553
Figure 1-1012 Install the M377, M477 scanner ............................................................................................................... 553
Figure 1-1013 Install the rear top cover .......................................................................................................................... 554
Figure 1-1014 Release two tabs ...................................................................................................................................... 554
Figure 1-1015 Install one tab ........................................................................................................................................... 555
Figure 1-1016 Rotate the left cover ................................................................................................................................. 556
ENWW xxxvii
Figure 1-1017 Make sure the tab does not get caught .................................................................................................... 556
Figure 1-1018 Raise the scanner ..................................................................................................................................... 557
Figure 1-1019 Position the hooks in the slots ................................................................................................................. 557
Figure 1-1020 Install the top hooks ................................................................................................................................. 558
Figure 1-1022 Install four tabs ........................................................................................................................................ 559
Figure 1-1023 Install two tabs ......................................................................................................................................... 559
Figure 1-1024 Install hinge pin ........................................................................................................................................ 560
Figure 1-1025 Install one screw ....................................................................................................................................... 560
Figure 1-1027 Install rear tab .......................................................................................................................................... 561
Figure 1-1029 Rotate the right cover ............................................................................................................................... 562
Figure 1-1031 Slide the cover .......................................................................................................................................... 563
Figure 1-1032 Rotate the front of the cover .................................................................................................................... 564
Figure 1-1034 Install the front and lower tabs ................................................................................................................ 565
Figure 1-1038 Close the front door .................................................................................................................................. 567
Figure 1-1039 Close the duplexer door ........................................................................................................................... 567
Figure 1-1040 Close the rear door ................................................................................................................................... 568
Figure 1-1041 Install the tray .......................................................................................................................................... 568
Figure 1-1042 Remove the tray ....................................................................................................................................... 570
Figure 1-1043 Release the front door .............................................................................................................................. 570
Figure 1-1044 Open the front door .................................................................................................................................. 571
Figure 1-1045 Open the duplexer door ............................................................................................................................ 571
Figure 1-1046 Open the rear door ................................................................................................................................... 572
Figure 1-1048 Remove one screw .................................................................................................................................... 573
Figure 1-1050 Locate the tabs ......................................................................................................................................... 574
Figure 1-1051 Release four tabs ...................................................................................................................................... 574
Figure 1-1052 Rotate the cover ....................................................................................................................................... 575
Figure 1-1053 Release one tab and two hooks ............................................................................................................... 575
Figure 1-1055 Remove the left cover .............................................................................................................................. 576
Figure 1-1056 Disconnect the scanner cables ................................................................................................................. 577
Figure 1-1057 Remove one screw and release the ground wire ..................................................................................... 577
xxxviii ENWW
Figure 1-1059 Release the scanner arm pin .................................................................................................................... 578
Figure 1-1060 Remove the scanner arm pin. ................................................................................................................... 579
Figure 1-1061 Release one tab ........................................................................................................................................ 579
Figure 1-1062 Remove the scanner cable cover .............................................................................................................. 580
Figure 1-1063 Release the cables .................................................................................................................................... 580
Figure 1-1064 Remove the scanner assembly ................................................................................................................ 581
Figure 1-1065 Recycle and unpack .................................................................................................................................. 581
Figure 1-1066 Install the scanner assembly .................................................................................................................... 582
Figure 1-1067 Press the cables ........................................................................................................................................ 582
Figure 1-1068 Position the scanner cable cover ............................................................................................................. 583
Figure 1-1069 Install the scanner cable cover ................................................................................................................. 583
Figure 1-1070 Install the scanner arm pin ....................................................................................................................... 584
Figure 1-1071 Secure the scanner arm pin ...................................................................................................................... 584
Figure 1-1073 Install the ground wire ............................................................................................................................. 585
Figure 1-1074 Install the M377, M477 scanner ............................................................................................................... 586
ENWW xxxix
Figure 1-1099 Release front lower tabs .......................................................................................................................... 602
Figure 1-1100 Release lower rear tab .............................................................................................................................. 602
Figure 1-1101 Release two front tabs ............................................................................................................................. 603
Figure 1-1102 Release upper tabs ................................................................................................................................... 603
Figure 1-1103 Remove the right cover ............................................................................................................................ 604
Figure 1-1110 Release front upper tabs .......................................................................................................................... 607
Figure 1-1112 Release top tabs ....................................................................................................................................... 608
Figure 1-1113 Release one tab and one hook ................................................................................................................. 609
Figure 1-1116 Remove one screw and release three tabs .............................................................................................. 610
Figure 1-1117 Disconnect one connector ........................................................................................................................ 611
Figure 1-1119 Install the power switch ........................................................................................................................... 612
Figure 1-1120 Check the spring position ......................................................................................................................... 612
Figure 1-1121 Install one screw and connect one connector .......................................................................................... 613
Figure 1-1122 Position two tabs ...................................................................................................................................... 613
Figure 1-1124 Install the right cover ............................................................................................................................... 614
Figure 1-1125 Install upper tabs ...................................................................................................................................... 615
Figure 1-1126 Install the front tabs ................................................................................................................................. 615
Figure 1-1127 Install the front lower tab ........................................................................................................................ 616
xl ENWW
Figure 1-1148 Open the cartridge drawer ....................................................................................................................... 628
Figure 1-1149 Remove the toner cartridge ..................................................................................................................... 628
Figure 1-1150 Slide the cartridge tray in ......................................................................................................................... 629
Figure 1-1157 Release bottom tabs ................................................................................................................................ 632
Figure 1-1158 Release three tabs .................................................................................................................................... 633
Figure 1-1168 Release the hinge arm .............................................................................................................................. 638
Figure 1-1169 Remove two screws .................................................................................................................................. 638
Figure 1-1170 Remove the cover ..................................................................................................................................... 639
Figure 1-1171 Pull the tray slide mechanism out ............................................................................................................ 639
Figure 1-1172 Rotate the cartridge tray to release one shaft ........................................................................................ 640
Figure 1-1173 Remove the cartridge tray ........................................................................................................................ 640
Figure 1-1175 Install the white clip ................................................................................................................................. 641
Figure 1-1176 Install the silver shaft ............................................................................................................................... 642
Figure 1-1177 Rotate the tray .......................................................................................................................................... 642
Figure 1-1178 Slide the tray slide mechanism in ............................................................................................................ 643
Figure 1-1179 Install the cover ........................................................................................................................................ 643
Figure 1-1180 Install two screws ..................................................................................................................................... 644
ENWW xli
Figure 1-1181 Install the hinge arm ................................................................................................................................ 644
Figure 1-1182 Position three tabs ................................................................................................................................... 645
Figure 1-1184 Install the left cover .................................................................................................................................. 646
Figure 1-1187 Engage two tabs ....................................................................................................................................... 647
Figure 1-1205 Slide the cartridge tray out ...................................................................................................................... 657
Figure 1-1206 Do not touch imaging drum ...................................................................................................................... 657
Figure 1-1207 Install a toner cartridge ............................................................................................................................ 658
Figure 1-1208 Close the toner cartridge drawer ............................................................................................................. 658
xlii ENWW
Figure 1-1236 Disconnect one connector and release cables from guides .................................................................... 673
Figure 1-1238 Remove the cartridge fan ......................................................................................................................... 674
Figure 1-1240 Install the cartridge fan ............................................................................................................................ 675
Figure 1-1241 Install three tabs ...................................................................................................................................... 676
Figure 1-1242 Connect one connector and install cables into guides ............................................................................. 676
ENWW xliii
Figure 1-1293 Release the spring .................................................................................................................................... 703
Figure 1-1295 Remove the power supply fan .................................................................................................................. 704
Figure 1-1297 Install the power supply fan ..................................................................................................................... 705
Figure 1-1299 Install the spring ....................................................................................................................................... 706
Figure 1-1300 Connect one connector and install cables into guides ............................................................................. 706
xliv ENWW
ENWW xlv
Figure 1-1364 Close the secondary transfer assembly ................................................................................................... 740
Figure 1-1365 Remove three screws ............................................................................................................................... 740
Figure 1-1366 Release the retention arm ........................................................................................................................ 741
Figure 1-1367 Remove the duplexer door ....................................................................................................................... 741
Figure 1-1368 Remove the rear door ............................................................................................................................... 742
Figure 1-1373 Remove the power supply fan and holder ............................................................................................... 744
Figure 1-1374 Check the connectors ............................................................................................................................... 745
Figure 1-1375 Disconnect five connectors and remove four screws .............................................................................. 745
Figure 1-1376 Remove two screws and release three tabs ............................................................................................ 746
Figure 1-1377 Remove the LVPS ...................................................................................................................................... 746
Figure 1-1379 Install the side tabs of the LVPS ............................................................................................................... 747
Figure 1-1380 Install the back tabs of the LVPS .............................................................................................................. 748
Figure 1-1382 Connect five connectors and install four screws ..................................................................................... 749
xlvi ENWW
Figure 1-1387 Connect one connector and install cables in the guides .......................................................................... 751
Figure 1-1388 Install the rear door .................................................................................................................................. 752
Figure 1-1389 Position the tab in the slot ....................................................................................................................... 752
Figure 1-1390 Install the duplexer door .......................................................................................................................... 753
Figure 1-1391 Install the retaining arm ........................................................................................................................... 753
Figure 1-1392 Install three screws .................................................................................................................................. 754
ENWW xlvii
xlviii ENWW
Figure 1-1490 Remove the fan duct ................................................................................................................................ 806
Figure 1-1491 Remove the pickup motor ........................................................................................................................ 806
Figure 1-1493 Install the pickup motor ........................................................................................................................... 807
Figure 1-1494 Install the fan duct .................................................................................................................................... 808
ENWW xlix
l ENWW
Figure 1-1579 Disconnect all connectors and remove one screw ................................................................................... 853
Figure 1-1580 Remove the driver PCA ............................................................................................................................. 853
Figure 1-1582 Install the driver PCA ................................................................................................................................ 854
Figure 1-1583 Fan connector locations ........................................................................................................................... 855
Figure 1-1584 Install one screw and connect all connectors .......................................................................................... 855
Figure 1-1585 Connect one connector ............................................................................................................................. 856
ENWW li
lii ENWW
Figure 1-1668 Remove the driver PCA holder .................................................................................................................. 899
Figure 1-1669 Remove the drum motor .......................................................................................................................... 900
Figure 1-1671 Install the drum motor ............................................................................................................................. 901
Figure 1-1672 Install the cables in the driver PCA holder ............................................................................................... 901
ENWW liii
Figure 1-1673 Install the driver PCA holder ..................................................................................................................... 902
Figure 1-1674 Connect one connector and install cables into the guides ...................................................................... 902
liv ENWW
ENWW lv
Figure 1-1795 Remove the driver PCA holder .................................................................................................................. 966
lvi ENWW
Figure 1-1796 Remove the developer motor ................................................................................................................... 967
Figure 1-1798 Install the developer motor ...................................................................................................................... 968
Figure 1-1799 Install the cables in the driver PCA holder ............................................................................................... 968
Figure 1-1800 Install the driver PCA holder ..................................................................................................................... 969
Figure 1-1801 Connect one connector and install cables into the guides ...................................................................... 969
ENWW lvii
Figure 1-1859 Lower the scanner .................................................................................................................................. 1000
Figure 1-1860 Close the front door ............................................................................................................................... 1000
Figure 1-1861 Close the duplexer door ......................................................................................................................... 1001
Figure 1-1862 Close the rear door ................................................................................................................................. 1001
Figure 1-1863 Install the tray ........................................................................................................................................ 1002
Figure 1-1864 Open the rear door ................................................................................................................................. 1004
Figure 1-1865 Remove one retainer collar .................................................................................................................... 1004
Figure 1-1866 Slide the assembly left ........................................................................................................................... 1005
Figure 1-1867 Remove the secondary transfer assembly ............................................................................................ 1005
Figure 1-1868 Recycle and unpack ................................................................................................................................ 1006
Figure 1-1869 Position the secondary transfer assembly ............................................................................................ 1006
Figure 1-1870 Slide the assembly right ......................................................................................................................... 1007
Figure 1-1871 Install one retainer collar ....................................................................................................................... 1007
Figure 1-1873 Open the duplexer door .......................................................................................................................... 1010
Figure 1-1875 Remove one screw and release the arm ................................................................................................ 1011
lviii ENWW
Figure 1-1881 Install the retaining arm ......................................................................................................................... 1014
Figure 1-1884 Remove the tray ..................................................................................................................................... 1017
Figure 1-1885 Release the front door ........................................................................................................................... 1018
Figure 1-1886 Open the front door ................................................................................................................................ 1018
Figure 1-1889 Remove one screw .................................................................................................................................. 1020
Figure 1-1891 Locate the tabs ....................................................................................................................................... 1021
Figure 1-1892 Release front lower tabs ........................................................................................................................ 1021
Figure 1-1893 Release lower rear tab ............................................................................................................................ 1022
Figure 1-1894 Release two front tabs ........................................................................................................................... 1022
Figure 1-1895 Release upper tabs ................................................................................................................................. 1023
Figure 1-1896 Remove the right cover .......................................................................................................................... 1023
Figure 1-1897 Raise the scanner ................................................................................................................................... 1024
Figure 1-1903 Release front upper tabs ........................................................................................................................ 1027
Figure 1-1904 Rotate the front of the cover .................................................................................................................. 1027
Figure 1-1905 Release top tabs ..................................................................................................................................... 1028
Figure 1-1906 Release one tab and one hook ............................................................................................................... 1028
Figure 1-1910 Release two tabs .................................................................................................................................... 1030
Figure 1-1912 Release bottom tabs .............................................................................................................................. 1031
Figure 1-1913 Release three tabs .................................................................................................................................. 1032
Figure 1-1918 Release four tabs .................................................................................................................................... 1034
ENWW lix
Figure 1-1919 Rotate the cover ..................................................................................................................................... 1035
Figure 1-1920 Release one tab and two hooks ............................................................................................................. 1035
Figure 1-1922 Remove the left cover ............................................................................................................................ 1036
Figure 1-1932 Slide the cartridge tray out .................................................................................................................... 1041
Figure 1-1933 Release two levers ................................................................................................................................. 1042
Figure 1-1934 Pull two levers out .................................................................................................................................. 1042
Figure 1-1935 Release one tab ...................................................................................................................................... 1043
Figure 1-1936 Remove the cover. .................................................................................................................................. 1043
Figure 1-1937 Disconnect two connectors .................................................................................................................... 1044
Figure 1-1939 Remove the fuser cover ......................................................................................................................... 1045
Figure 1-1940 Remove two screws ................................................................................................................................ 1045
Figure 1-1942 Slide the ITB out ..................................................................................................................................... 1046
Figure 1-1944 Clean the mylar strips ............................................................................................................................ 1047
Figure 1-1945 Check tabs on the end of the ITB ........................................................................................................... 1048
Figure 1-1946 Lower both tabs on each side of the ITB to the position shown ............................................................ 1048
Figure 1-1947 Slide the ITB in ........................................................................................................................................ 1049
Figure 1-1948 Install two screws ................................................................................................................................... 1049
Figure 1-1949 Install the fuser cover ............................................................................................................................. 1050
Figure 1-1950 Connect two connectors ......................................................................................................................... 1050
Figure 1-1951 Install the cover. ..................................................................................................................................... 1051
Figure 1-1952 Push two levers in .................................................................................................................................. 1052
Figure 1-1953 Push two levers in (different view) ........................................................................................................ 1052
Figure 1-1954 Rotate two levers into place ................................................................................................................... 1053
Figure 1-1955 Slide the cartridge tray in ....................................................................................................................... 1053
lx ENWW
Figure 1-1965 Position three tabs ................................................................................................................................. 1058
Figure 1-1966 Install one tab ......................................................................................................................................... 1059
Figure 1-1967 Install the left cover ............................................................................................................................... 1060
Figure 1-1968 Make sure the tab does not get caught .................................................................................................. 1060
Figure 1-1969 Install four tabs ...................................................................................................................................... 1061
Figure 1-1970 Engage two tabs ..................................................................................................................................... 1061
Figure 1-1971 Install hinge pin ...................................................................................................................................... 1062
Figure 1-1972 Install one screw ..................................................................................................................................... 1062
Figure 1-1974 Rotate the left cover ............................................................................................................................... 1064
Figure 1-1977 Position the hooks in the slots ............................................................................................................... 1065
Figure 1-1978 Install the top hooks ............................................................................................................................... 1066
Figure 1-1981 Install two tabs ....................................................................................................................................... 1067
Figure 1-1985 Position two tabs .................................................................................................................................... 1069
Figure 1-1986 Install rear tab ........................................................................................................................................ 1070
Figure 1-1987 Install the right cover ............................................................................................................................. 1070
Figure 1-1988 Install upper tabs ................................................................................................................................... 1071
Figure 1-1989 Install the front tabs ............................................................................................................................... 1071
Figure 1-1990 Install the front lower tab ...................................................................................................................... 1072
Figure 1-1996 Rotate the right cover ............................................................................................................................. 1075
Figure 1-1998 Slide the cover ........................................................................................................................................ 1076
ENWW lxi
Figure 1-2001 Install the front and lower tabs .............................................................................................................. 1077
Figure 1-2011 Open the cartridge drawer ..................................................................................................................... 1084
Figure 1-2012 Remove the toner cartridge ................................................................................................................... 1085
lxii ENWW
Figure 1-2061 Release two levers ................................................................................................................................. 1109
Figure 1-2062 Pull two levers out .................................................................................................................................. 1110
Figure 1-2064 Remove the cover. .................................................................................................................................. 1111
Figure 1-2067 Remove the fuser cover ......................................................................................................................... 1112
Figure 1-2070 Slide the ITB out ..................................................................................................................................... 1114
Figure 1-2071 Release the hinge arm ............................................................................................................................ 1114
Figure 1-2073 Remove the cover ................................................................................................................................... 1115
Figure 1-2074 Pull the tray slide mechanism out ......................................................................................................... 1116
Figure 1-2075 Rotate the cartridge tray to release one shaft ...................................................................................... 1116
Figure 1-2076 Remove the cartridge tray ..................................................................................................................... 1117
Figure 1-2077 Location of the registration density sensor ........................................................................................... 1117
Figure 1-2078 Disconnect one connector and release cables ....................................................................................... 1118
Figure 1-2080 Slide the sensor and cable guide right ................................................................................................... 1119
Figure 1-2081 Release the connector ............................................................................................................................ 1119
Figure 1-2082 Remove the registration density sensor and guide ............................................................................... 1120
ENWW lxiii
Figure 1-2083 Release the cables from the guides ....................................................................................................... 1120
Figure 1-2084 Remove the cable guide ......................................................................................................................... 1121
Figure 1-2086 Reinstall spring ....................................................................................................................................... 1122
Figure 1-2087 Install the cables in the guides ............................................................................................................... 1122
Figure 1-2088 Install the connector .............................................................................................................................. 1123
Figure 1-2089 Install the cable guide tabs .................................................................................................................... 1123
Figure 1-2091 Install the registration density sensor ................................................................................................... 1124
Figure 1-2092 Connect one connector ........................................................................................................................... 1125
Figure 1-2093 Install the white clip ............................................................................................................................... 1125
Figure 1-2094 Install the silver shaft ............................................................................................................................. 1126
Figure 1-2095 Rotate the tray ....................................................................................................................................... 1126
Figure 1-2096 Slide the tray slide mechanism in .......................................................................................................... 1127
Figure 1-2097 Install the cover ...................................................................................................................................... 1127
Figure 1-2099 Install the hinge arm .............................................................................................................................. 1128
Figure 1-2100 Clean the mylar strips ............................................................................................................................ 1129
Figure 1-2101 Check tabs on the end of the ITB ........................................................................................................... 1130
Figure 1-2102 Lower both tabs on each side of the ITB to the position shown ............................................................ 1130
Figure 1-2103 Slide the ITB in ........................................................................................................................................ 1131
Figure 1-2105 Install the fuser cover ............................................................................................................................. 1132
Figure 1-2107 Install the cover. ..................................................................................................................................... 1133
Figure 1-2108 Push two levers in .................................................................................................................................. 1134
Figure 1-2109 Push two levers in (different view) ........................................................................................................ 1134
Figure 1-2110 Rotate two levers into place ................................................................................................................... 1135
lxiv ENWW
ENWW lxv
Figure 1-2165 Do not touch imaging drum .................................................................................................................... 1163
Figure 1-2166 Install a toner cartridge .......................................................................................................................... 1164
Figure 1-2167 Close the toner cartridge drawer ........................................................................................................... 1164
lxvi ENWW
Figure 1-2211 Close the secondary transfer assembly ................................................................................................. 1188
Figure 1-2212 Remove three screws ............................................................................................................................. 1188
Figure 1-2213 Release the retention arm ...................................................................................................................... 1189
Figure 1-2214 Remove the duplexer door ..................................................................................................................... 1189
Figure 1-2215 Disconnect two connectors and remove cables from guides ................................................................ 1190
Figure 1-2216 Remove six screws ................................................................................................................................. 1190
Figure 1-2218 Remove the re-pickup assembly ............................................................................................................ 1191
Figure 1-2220 Position the foot through the opening .................................................................................................. 1192
Figure 1-2222 Install six screws .................................................................................................................................... 1193
Figure 1-2223 Connect two connectors and install cables in guides ............................................................................ 1194
Figure 1-2224 Position the tab in the slot ..................................................................................................................... 1194
Figure 1-2225 Install the duplexer door ........................................................................................................................ 1195
Figure 1-2227 Install three screws ................................................................................................................................ 1196
ENWW lxvii
lxviii ENWW
Figure 1-2295 Check the cables ..................................................................................................................................... 1232
Figure 1-2296 Disconnect all of the connectors ............................................................................................................ 1233
Figure 1-2299 Remove the engine controller PCA ......................................................................................................... 1234
Figure 1-2301 Position the engine controller PCA ........................................................................................................ 1235
Figure 1-2304 Connect all of the connectors ................................................................................................................ 1237
ENWW lxix
lxx ENWW
Figure 1-2375 Remove the rear door ............................................................................................................................. 1275
Figure 1-2385 Remove four screws and release cables ................................................................................................ 1280
Figure 1-2386 Remove one cover .................................................................................................................................. 1281
Figure 1-2388 Remove the shaft ................................................................................................................................... 1282
Figure 1-2389 Locate the tray sensor switch ................................................................................................................ 1282
Figure 1-2391 Release the tray sensor switch .............................................................................................................. 1283
Figure 1-2392 Remove the tray sensor switch .............................................................................................................. 1284
Figure 1-2393 Remove the lifter drive assembly .......................................................................................................... 1284
Figure 1-2395 Install the lifter drive assembly ............................................................................................................. 1285
Figure 1-2396 Install the tray sensor switch cable ....................................................................................................... 1286
Figure 1-2397 Install the tray sensor switch ................................................................................................................. 1286
Figure 1-2398 Install the shaft ...................................................................................................................................... 1287
Figure 1-2400 Install one cover ..................................................................................................................................... 1288
Figure 1-2401 Install four screws and cables ................................................................................................................ 1288
Figure 1-2410 Install the rear door ................................................................................................................................ 1293
ENWW lxxi
lxxii ENWW
ENWW lxxiii
Figure 1-2516 Disconnect one connector ...................................................................................................................... 1349
Figure 1-2517 Disconnect all connectors and remove one screw ................................................................................. 1349
Figure 1-2518 Remove the driver PCA ........................................................................................................................... 1350
Figure 1-2519 Disconnect one connector and release cables from guides .................................................................. 1350
Figure 1-2523 Remove the power supply fan and holder ............................................................................................. 1352
Figure 1-2524 Check the connectors ............................................................................................................................. 1353
Figure 1-2525 Disconnect five connectors and remove four screws ............................................................................ 1353
Figure 1-2526 Remove two screws and release three tabs .......................................................................................... 1354
Figure 1-2527 Remove the LVPS .................................................................................................................................... 1354
Figure 1-2528 Remove the fan duct .............................................................................................................................. 1355
Figure 1-2529 Remove the pickup motor ...................................................................................................................... 1355
lxxiv ENWW
Figure 1-2544 Release the cables from the cable guides ............................................................................................. 1363
Figure 1-2545 Release the cables .................................................................................................................................. 1363
Figure 1-2546 Remove the pickup assembly ................................................................................................................. 1364
Figure 1-2549 Thread the cables ................................................................................................................................... 1365
Figure 1-2550 Install the pickup assembly .................................................................................................................... 1366
Figure 1-2551 Install the cable ...................................................................................................................................... 1366
Figure 1-2552 Install the cables in the cable guides ..................................................................................................... 1367
Figure 1-2565 Install the pickup motor ......................................................................................................................... 1373
Figure 1-2566 Install the fan duct ................................................................................................................................. 1374
Figure 1-2567 Install the side tabs of the LVPS ............................................................................................................. 1374
Figure 1-2568 Install the back tabs of the LVPS ............................................................................................................ 1375
Figure 1-2570 Connect five connectors and install four screws ................................................................................... 1376
ENWW lxxv
Figure 1-2575 Connect one connector and install cables in the guides ........................................................................ 1378
Figure 1-2576 Install the driver PCA .............................................................................................................................. 1379
Figure 1-2577 Fan connector locations ......................................................................................................................... 1379
Figure 1-2578 Install one screw and connect all connectors ........................................................................................ 1380
lxxvi ENWW
ENWW lxxvii
lxxviii ENWW
Figure 1-2723 Release the tray 1 feed guide ................................................................................................................. 1455
Figure 1-2724 Slide the roller holder ............................................................................................................................. 1456
Figure 1-2725 Remove the pickup and feed rollers ...................................................................................................... 1456
Figure 1-2727 Remove the roller holder ........................................................................................................................ 1457
Figure 1-2728 Remove the front feed guide assembly ................................................................................................. 1458
Figure 1-2730 Position the front feed guide assembly ................................................................................................. 1459
Figure 1-2731 Position the flag ..................................................................................................................................... 1459
Figure 1-2732 Install the front feed guide assembly .................................................................................................... 1460
Figure 1-2733 Install the roller holder ........................................................................................................................... 1460
ENWW lxxix
lxxx ENWW
ENWW lxxxi
lxxxii ENWW
ENWW lxxxiii
Figure 1-2917 Remove the rear feed guide assembly ................................................................................................... 1555
Figure 1-2919 Install the rear feed guide assembly ...................................................................................................... 1556
lxxxiv ENWW
ENWW lxxxv
lxxxvi ENWW
ENWW lxxxvii
lxxxviii ENWW
Figure 1-3109 Release five tabs .................................................................................................................................... 1654
Figure 1-3110 Remove the registration assembly ........................................................................................................ 1655
Figure 1-3112 Position the registration assembly ........................................................................................................ 1656
Figure 1-3114 Install five tabs ....................................................................................................................................... 1657
Figure 1-3115 Check the tabs ........................................................................................................................................ 1657
ENWW lxxxix
xc ENWW
ENWW xci
Figure 1-3252 Release six tabs ...................................................................................................................................... 1729
Figure 1-3253 Remove the rear top cover ..................................................................................................................... 1729
Figure 1-3254 Disconnect the scanner cables ............................................................................................................... 1730
Figure 1-3255 Remove one screw and release the ground wire ................................................................................... 1730
Figure 1-3257 Release the scanner arm pin .................................................................................................................. 1731
Figure 1-3258 Remove the scanner arm pin. ................................................................................................................ 1732
Figure 1-3260 Remove the scanner cable cover ........................................................................................................... 1733
Figure 1-3262 Remove the scanner assembly .............................................................................................................. 1734
Figure 1-3263 Disconnect one connector and remove four screws .............................................................................. 1734
Figure 1-3264 Remove the fax cover ............................................................................................................................. 1735
Figure 1-3265 Remove the fax PCA ............................................................................................................................... 1735
Figure 1-3267 Remove one screw and the sheet metal plate ....................................................................................... 1736
Figure 1-3268 Lower the support arm and remove one screw ..................................................................................... 1737
Figure 1-3269 Remove the scanner support arm .......................................................................................................... 1737
Figure 1-3271 Release the control panel cover ............................................................................................................. 1738
xcii ENWW
Figure 1-3272 Remove the control panel cover ............................................................................................................ 1739
Figure 1-3273 Release the flat cable ............................................................................................................................. 1739
Figure 1-3276 Refasten the control panel to the top cover .......................................................................................... 1741
Figure 1-3277 Release the USB cable ............................................................................................................................ 1741
Figure 1-3279 Release one retainer and three tabs ...................................................................................................... 1742
Figure 1-3280 Remove the top cover ............................................................................................................................. 1743
Figure 1-3283 Disconnect the antenna ......................................................................................................................... 1744
Figure 1-3285 Remove the guide ................................................................................................................................... 1745
Figure 1-3288 Remove screw and release two tabs ...................................................................................................... 1747
Figure 1-3289 Remove two screws and release one tab ............................................................................................... 1747
Figure 1-3291 Locate the memory PCA ......................................................................................................................... 1748
Figure 1-3292 Remove the memory PCA ....................................................................................................................... 1749
Figure 1-3294 Position the memory PCA ....................................................................................................................... 1750
Figure 1-3295 Install the memory PCA .......................................................................................................................... 1750
Figure 1-3296 Position the top cover ............................................................................................................................ 1751
Figure 1-3297 Engage tab and install screws ................................................................................................................ 1751
Figure 1-3298 Install two tabs and one screw .............................................................................................................. 1752
Figure 1-3301 Install the guide ...................................................................................................................................... 1753
Figure 1-3305 Connect the antenna .............................................................................................................................. 1755
Figure 1-3307 Install one retainer and three tabs ........................................................................................................ 1756
Figure 1-3309 Install the USB cable ............................................................................................................................... 1757
ENWW xciii
Figure 1-3313 Install the flat cable ................................................................................................................................ 1759
Figure 1-3314 Install the control panel cover ............................................................................................................... 1760
Figure 1-3317 Install the scanner support arm ............................................................................................................. 1761
Figure 1-3318 Raise the metal plate ............................................................................................................................. 1762
Figure 1-3319 Lower the support arm and install one screw ....................................................................................... 1762
Figure 1-3320 Install the metal plate ............................................................................................................................ 1763
Figure 1-3323 Install the fax PCA .................................................................................................................................. 1764
Figure 1-3324 Install the fax cover ................................................................................................................................ 1765
Figure 1-3325 Install four screws and connect one connector ..................................................................................... 1765
Figure 1-3326 Install the scanner assembly ................................................................................................................. 1766
Figure 1-3327 Press the cables ...................................................................................................................................... 1766
Figure 1-3328 Position the scanner cable cover ........................................................................................................... 1767
Figure 1-3329 Install the scanner cable cover ............................................................................................................... 1767
Figure 1-3330 Install the scanner arm pin .................................................................................................................... 1768
Figure 1-3331 Secure the scanner arm pin .................................................................................................................... 1768
Figure 1-3333 Install the ground wire ........................................................................................................................... 1769
Figure 1-3334 Install the M377, M477 scanner ............................................................................................................. 1770
Figure 1-3335 Install the rear top cover ........................................................................................................................ 1770
xciv ENWW
ENWW xcv
Figure 1-3413 Remove one screw and release one tab ................................................................................................ 1812
Figure 1-3415 Disconnect four connectors ................................................................................................................... 1813
Figure 1-3416 Lift the flat cable .................................................................................................................................... 1814
Figure 1-3418 Remove the bracket ............................................................................................................................... 1815
Figure 1-3420 Remove the grounding plate .................................................................................................................. 1816
Figure 1-3422 Remove the USB bracket ........................................................................................................................ 1817
Figure 1-3424 Remove the front door switch holder .................................................................................................... 1818
Figure 1-3425 Release one tab on the cover ................................................................................................................. 1818
Figure 1-3431 Remove the exhaust duct ...................................................................................................................... 1821
Figure 1-3432 Release three springs ............................................................................................................................. 1822
Figure 1-3433 Lift the duct to release the spring .......................................................................................................... 1822
Figure 1-3434 Remove the laser scanner ...................................................................................................................... 1823
xcvi ENWW
Figure 1-3436 Install three tabs .................................................................................................................................... 1824
Figure 1-3438 Spring position ....................................................................................................................................... 1825
Figure 1-3439 Reposition the spring ............................................................................................................................. 1825
Figure 1-3440 Install three springs ............................................................................................................................... 1826
Figure 1-3441 Lift the duct to install the spring ............................................................................................................ 1826
Figure 1-3442 Position the exhaust duct ...................................................................................................................... 1827
Figure 1-3445 Position the cover ................................................................................................................................... 1828
Figure 1-3449 Position the front door switch holder .................................................................................................... 1830
Figure 1-3450 Position the spring and install one screw .............................................................................................. 1831
Figure 1-3451 Install the USB bracket ........................................................................................................................... 1831
Figure 1-3453 Install the grounding plate ..................................................................................................................... 1832
Figure 1-3455 Install the bracket ................................................................................................................................... 1833
Figure 1-3457 Position the flat cable ............................................................................................................................ 1834
Figure 1-3458 Connect four connectors ........................................................................................................................ 1835
Figure 1-3460 Position the NFC PCA .............................................................................................................................. 1836
Figure 1-3461 Install one tab and one screw ................................................................................................................ 1836
ENWW xcvii
xcviii ENWW
Figure 1-3556 Disconnect four connectors ................................................................................................................... 1886
Figure 1-3557 Lift the flat cable .................................................................................................................................... 1886
ENWW xcix
Figure 1-3560 Remove four screws ............................................................................................................................... 1888
Figure 1-3562 Remove the metal bracket ..................................................................................................................... 1889
Figure 1-3564 Remove the front door switch holder .................................................................................................... 1890
Figure 1-3565 Release one tab on the cover ................................................................................................................. 1890
Figure 1-3571 Remove the exhaust duct ...................................................................................................................... 1893
Figure 1-3572 Release three springs ............................................................................................................................. 1894
Figure 1-3573 Lift the duct to release the spring .......................................................................................................... 1894
Figure 1-3574 Remove the laser scanner ...................................................................................................................... 1895
Figure 1-3578 Spring position ....................................................................................................................................... 1897
Figure 1-3580 Install three springs ............................................................................................................................... 1898
Figure 1-3581 Lift the duct to install the spring ............................................................................................................ 1898
Figure 1-3582 Position the exhaust duct ...................................................................................................................... 1899
Figure 1-3589 Position the front door switch holder .................................................................................................... 1902
Figure 1-3590 Position the spring and install one screw .............................................................................................. 1903
Figure 1-3591 Position the metal bracket ..................................................................................................................... 1903
Figure 1-3592 Install the metal bracket ........................................................................................................................ 1904
Figure 1-3593 Insert the cables ..................................................................................................................................... 1904
Figure 1-3594 Install four screws .................................................................................................................................. 1905
Figure 1-3597 Position the flat cable ............................................................................................................................ 1906
Figure 1-3598 Connect four connectors ........................................................................................................................ 1907
c ENWW
ENWW ci
cii ENWW
ENWW ciii
Figure 1-3740 Disconnect six connectors ...................................................................................................................... 1979
Figure 1-3742 Remove five screws ................................................................................................................................ 1980
Figure 1-3743 Remove the fuser ................................................................................................................................... 1981
Figure 1-3745 Position the fuser ................................................................................................................................... 1982
Figure 1-3746 Install five screws ................................................................................................................................... 1982
Figure 1-3748 Connect six connectors .......................................................................................................................... 1983
civ ENWW
ENWW cv
cvi ENWW
ENWW cvii
Figure 1-3912 Disconnect eight connectors .................................................................................................................. 2067
Figure 1-3917 Install the lever through the opening .................................................................................................... 2070
Figure 1-3918 Switchback lever shaft ........................................................................................................................... 2070
Figure 1-3919 Switchback lever position ...................................................................................................................... 2071
Figure 1-3922 Connect eight connectors ....................................................................................................................... 2072
Figure 1-3924 Position the guide ................................................................................................................................... 2073
cviii ENWW
ENWW cix
cx ENWW
Figure 1-4035 Release the retainer arm ........................................................................................................................ 2130
Figure 1-4036 Disconnect two connectors and remove three screws .......................................................................... 2131
Figure 1-4037 Remove the fuser power supply ............................................................................................................ 2131
Figure 1-4042 Install the retainer arm .......................................................................................................................... 2134
ENWW cxi
cxii ENWW
Figure 1-4099 Remove the fuser motor ........................................................................................................................ 2164
Figure 1-4101 Install the fuser motor ........................................................................................................................... 2165
ENWW cxiii
cxiv ENWW
Figure 1-4210 Disconnect eight connectors .................................................................................................................. 2221
ENWW cxv
Figure 1-4220 Remove the duplex drive assembly ....................................................................................................... 2226
Figure 1-4223 Install the duplex drive assembly .......................................................................................................... 2228
Figure 1-4230 Install the lever through the opening .................................................................................................... 2231
Figure 1-4231 Switchback lever shaft ........................................................................................................................... 2232
Figure 1-4232 Switchback lever position ...................................................................................................................... 2232
Figure 1-4235 Connect eight connectors ....................................................................................................................... 2234
Figure 1-4237 Position the guide ................................................................................................................................... 2235
cxvi ENWW
ENWW cxvii
cxviii ENWW
Figure 1-4351 Locate the wireless antenna .................................................................................................................. 2294
Figure 1-4352 Loosen the tape ...................................................................................................................................... 2294
Figure 1-4353 Remove the antenna .............................................................................................................................. 2295
Figure 1-4355 Remove protective backing from adhesive strip ................................................................................... 2296
Figure 1-4356 Install the top adhesive strip .................................................................................................................. 2296
Figure 1-4357 Peel the silver tape up ............................................................................................................................ 2297
Figure 1-4358 Remove the protective backing .............................................................................................................. 2297
Figure 1-4359 Press the silver tape ............................................................................................................................... 2298
Figure 1-4360 Position the tape .................................................................................................................................... 2298
Figure 1-4361 Remove the protective cover ................................................................................................................. 2299
ENWW cxix
Figure 1-4405 Disconnect all of the connectors) ........................................................................................................... 2323
Figure 1-4408 Remove the formatter PCA .................................................................................................................... 2324
Figure 1-4409 Remove the wireless PCA ....................................................................................................................... 2325
Figure 1-4411 Position the wireless PCA ....................................................................................................................... 2326
Figure 1-4412 Connect the wireless PCA ....................................................................................................................... 2326
Figure 1-4414 Position the formatter PCA ports ........................................................................................................... 2327
cxx ENWW
Figure 1-4445 Slide the wireless PCA holder forward ................................................................................................... 2344
Figure 1-4446 Remove the wireless PCA holder ............................................................................................................ 2345
Figure 1-4448 Release the cable .................................................................................................................................... 2346
Figure 1-4449 Feed the cable through the holder ......................................................................................................... 2346
Figure 1-4450 Remove the wireless PCA from the holder ............................................................................................. 2347
Figure 1-4454 Install the wireless PCA on the holder ................................................................................................... 2349
Figure 1-4455 Feed the cable through the holder ......................................................................................................... 2349
Figure 1-4458 Install the wireless PCA holder ............................................................................................................... 2351
Figure 1-4459 Slide the wireless PCA holder ................................................................................................................. 2351
ENWW cxxi
Figure 1-4496 Disconnect all of the connectors) ........................................................................................................... 2372
Figure 1-4499 Remove the formatter PCA .................................................................................................................... 2373
Figure 1-4500 Remove the wireless PCA ....................................................................................................................... 2374
Figure 1-4501 Remove the bracket ............................................................................................................................... 2374
cxxii ENWW
Figure 1-4503 Install the bracket ................................................................................................................................... 2375
Figure 1-4504 Position the wireless PCA ....................................................................................................................... 2376
Figure 1-4505 Connect the wireless PCA ....................................................................................................................... 2376
Figure 1-4507 Position the formatter PCA ports ........................................................................................................... 2377
ENWW cxxiii
Figure 1-4554 Disconnect one connector and release two tabs ................................................................................... 2403
Figure 1-4555 Disconnect one connector and remove the sensor ............................................................................... 2404
Figure 1-4559 Install two tabs and connect one connector .......................................................................................... 2406
cxxiv ENWW
ENWW cxxv
cxxvi ENWW
ENWW cxxvii
cxxviii ENWW
ENWW cxxix
cxxx ENWW
Figure 1-4852 Locate the walk-up USB port .................................................................................................................. 2558
Figure 1-4853 Remove screws and disconnect connector ............................................................................................ 2559
Figure 1-4854 Remove the walk-up USB port ............................................................................................................... 2559
Figure 1-4856 Install the walk-up USB port .................................................................................................................. 2560
Figure 1-4857 Install screws and connect connector .................................................................................................... 2561
ENWW cxxxi
cxxxii ENWW
Figure 1-4944 Slide the walk-up USB port .................................................................................................................... 2606
Figure 1-4945 Remove the walk-up USB port ............................................................................................................... 2607
Figure 1-4947 Connect the walk-up USB port ............................................................................................................... 2608
Figure 1-4948 Install the walk-up USB port .................................................................................................................. 2608
ENWW cxxxiii
cxxxiv ENWW
Figure 1-5027 Disconnect one connector and release two tabs ................................................................................... 2649
Figure 1-5028 Remove the drawer connector ............................................................................................................... 2650
Figure 1-5030 Install the drawer connector .................................................................................................................. 2651
Figure 1-5031 Install two tabs and connect one connector .......................................................................................... 2651
ENWW cxxxv
cxxxvi ENWW
Figure 1-5085 Remove the rear cover ........................................................................................................................... 2685
Figure 1-5087 Install the tabs ........................................................................................................................................ 2686
Figure 1-5109 Remove the PCA cover ............................................................................................................................ 2699
Figure 1-5112 Remove the foot ..................................................................................................................................... 2700
Figure 1-5114 Remove the baseplate ............................................................................................................................ 2701
ENWW cxxxvii
Figure 1-5117 Remove the feed frame assembly ......................................................................................................... 2703
Figure 1-5118 Disconnect connector and remove five screws ...................................................................................... 2703
Figure 1-5119 Locate the switch cable assembly .......................................................................................................... 2704
Figure 1-5121 Remove the switch cable assembly and holder ..................................................................................... 2705
Figure 1-5122 Remove the cables from the guides ...................................................................................................... 2705
Figure 1-5124 Remove the switch cable assembly ....................................................................................................... 2706
Figure 1-5126 Position the switch cable assembly ....................................................................................................... 2707
Figure 1-5128 Install the switch cable assembly .......................................................................................................... 2708
Figure 1-5130 Install the cables and connect one connector ....................................................................................... 2709
Figure 1-5131 Install the feed frame assembly ............................................................................................................ 2710
Figure 1-5133 Install the cables .................................................................................................................................... 2711
Figure 1-5135 Rotate the baseplate down .................................................................................................................... 2712
Figure 1-5139 Install the PCA cover ............................................................................................................................... 2714
cxxxviii ENWW
Figure 1-5176 Remove the cables ................................................................................................................................. 2734
Figure 1-5180 Release the tray sensor switch cables ................................................................................................... 2736
Figure 1-5181 Remove eight screws ............................................................................................................................. 2737
Figure 1-5182 Remove the cross braces ........................................................................................................................ 2737
Figure 1-5183 Remove screws and release tabs ........................................................................................................... 2738
Figure 1-5184 Remove the tray guide ........................................................................................................................... 2738
Figure 1-5188 Install the tray guide .............................................................................................................................. 2740
Figure 1-5189 Install screws and tabs ........................................................................................................................... 2741
Figure 1-5190 Install the cross braces ........................................................................................................................... 2741
Figure 1-5191 Install eight screws ................................................................................................................................. 2742
Figure 1-5192 Install the tray sensor switch cables ...................................................................................................... 2742
ENWW cxxxix
cxl ENWW
Figure 1-5256 Remove the motor .................................................................................................................................. 2776
Figure 1-5268 Install the motor ..................................................................................................................................... 2782
ENWW cxli
cxlii ENWW
Figure 1-5354 Install the pickup and feed rollers .......................................................................................................... 2827
ENWW cxliii
cxliv ENWW
ENWW cxlv
cxlvi ENWW
ENWW cxlvii
Figure 1-5543 Remove the front paper feed guide ....................................................................................................... 2926
Figure 1-5545 Remove the paper feed assembly .......................................................................................................... 2927
Figure 1-5547 Install the paper feed assembly ............................................................................................................. 2928
Figure 1-5550 Install the front paper feed guide .......................................................................................................... 2929
cxlviii ENWW
ENWW cxlix
Figure 1-5622 Disconnect the wire harness .................................................................................................................. 2968
Figure 1-5624 Connect the wire harness ....................................................................................................................... 2969
Figure 1-5627 Install the connector holder ................................................................................................................... 2970
Figure 1-5644 Position the driver PCA ........................................................................................................................... 2980
cl ENWW
Figure 2-1 Base printer, M452 ........................................................................................................................................ 2987
Figure 2-2 Base printer, M377 and M477 ...................................................................................................................... 2988
Figure 2-3 550-sheet paper feeder (all models) ........................................................................................................... 2989
Figure 2-4 Document feeder and scanner (M377, M477) .............................................................................................. 2994
Figure 2-5 M452 covers and control panels ................................................................................................................... 2996
Figure 2-6 M377, M477 covers and control panel ......................................................................................................... 2998
Figure 2-7 Internal components (1 of 5) ........................................................................................................................ 3000
Figure 2-10 Internal components (4 of 5) ...................................................................................................................... 3006
Figure 2-11 Internal components (5 of 5) ...................................................................................................................... 3008
Figure 2-12 550-sheet paper feeder covers .................................................................................................................. 3010
Figure 2-13 550-sheet paper feeder main body (1 of 2) ............................................................................................... 3012
Figure 2-14 550-sheet paper feeder main body (2 of 2) ............................................................................................... 3014
ENWW cli
clii ENWW
1 Removal and replacement
● For additional service and support
● Removal and replacement strategy
● Service approach
● Order parts by authorized service providers
● Removal and replacement procedures
ENWW 1
For additional service and support
home.do.
Channel partners, go to HP Channel Services Network (CSN) at https://h30125.www3.hp.com/hpcsn.

2 Chapter 1 Removal and replacement ENWW

Removal and replacement strategy
Introduction
The printer uses a field repair strategy. Defective parts are diagnosed and replaced at the Field Replaceable
Unit (FRU) assembly level. Repair normally begins by using the printer internal diagnostics and the following
two-step process:
1. Isolate the problem to the major system (for example, the network or server, or the printer).
2. Troubleshoot the problem by using the procedures in the troubleshooting chapter.
After locating a faulty part, the printer can usually be repaired at the assembly level by replacing FRUs. Some
mechanical assemblies might need to be repaired at the subassembly level. HP does not support replacement
of components on the printed circuit assemblies.
The user replaces toner cartridges as they are depleted. Additional instructions about other user-replaceable
parts are provided in this section.
The printer tracks the amount of use on the customer-replaceable supplies by keeping a page count. The
printer prompts the user to replace certain items when a supply is depleted or a specific number of pages has
been printed.
Swapping toner cartridges between printers might cause a misrepresentation of supply life values and is not
recommended.
Considerations during removal and replacement

HP does not support repairing individual subassemblies or troubleshooting to the printed-circuit assembly
(PCA) component level.
WARNING! Never operate or service the printer with the protective cover removed from the laser scanner
assembly. The reflected beam, although invisible, can cause damage the eyes.
The sheet-metal parts can have sharp edges. Be careful when handling sheet-metal parts.
Turn the printer off, wait 5 seconds, and then remove the power cord before attempting to service the printer.
If this warning is not followed, severe injury and damage to the printer can result. The power must be on for
certain functional checks during troubleshooting. However, the power cord must be disconnected during
parts removal. AC voltage is still present inside the printer when the power switch is in the off position. The
power cord must be disconnected before servicing the printer.
CAUTION: Incorrectly routed or loose wire harnesses might interfere with other internal components or
assemblies and be damaged, pinched, or frayed. Make sure that wire harnesses are correctly routed and
retained when installing assemblies.
Do not bend or fold the flat cables during removal or installation.
Do not expose the toner cartridge (or toner cartridges), to strong light even for a short time.
Be careful when using a screwdriver to remove the printer covers. The screwdriver might slip and cause
cosmetic damage to the covers.
IMPORTANT: When an assembly is removed that includes a rating plate or tag (or a printer code label), make
sure to transfer the plate or tag (or code label) to the replacement assembly.
ENWW Removal and replacement strategy 3

NOTE: During assembly removal and replacement, or if the printer is moved, remove the toner cartridge or
cartridges.
Toner is a non-poisonous substance composed of plastic and a small number of colored components. If toner
gets on the skin or clothing, wipe it off with dry tissue paper and wash in cold water. Hot water sets toner and
it might be difficult, or impossible, to remove. Toner easily breaks down vinyl materials—avoid letting toner
contact with vinyl.
During assembly removal and replacement, or if the printer is moved, remove the tray cassette or cassettes.
TIP: For clarity, some figures in this chapter show assemblies removed that are not required to be removed
to service the printer (for example, the scanner and document feeder assemblies). The procedures in this
manual are correct for this printer.
Electrostatic discharge
CAUTION: Some parts are sensitive to electrostatic discharge (ESD). Look for the ESD reminder when
removing printer parts. Always perform service work at an ESD-protected workstation or mat. If an ESD
workstation or mat is not available, touch the sheet-metal chassis to provide a static ground before touching
an ESD-sensitive assembly.
Protect the ESD-sensitive assemblies by placing them in ESD pouches when they are out of the printer.
Required tools
● #2 Phillips screwdriver with a magnetic tip and a 152-mm (6-in) shaft length
● Small, flat-blade screwdriver
● Needle-nose pliers
● ESD strap (if one is available)
● Penlight
CAUTION: Always use a #2 Phillips screwdriver (callout 1). Do not use a Pozidriv screwdriver (callout 2) or
any motorized screwdriver. These can damage screws or screw threads.
Figure 1-1 Screwdrivers

Fasteners used in this printer
WARNING! Make sure that assemblies are replaced with the correct screw type. Using the incorrect screw
(for example, substituting a long screw for the correct shorter screw) can cause damage to the printer or
interfere with printer operation. Do not intermix screws that are removed from one assembly with the screws
that are removed from another assembly.
NOTE: To install a screw, first turn it counterclockwise to align it with the existing thread pattern, and then
carefully turn it clockwise to tighten. Do not overtighten. If a self-tapping screw-hole becomes stripped,
repair the screw-hole or replace the affected assembly.
Always take note of the length, diameter, color, type, and location of each removed screw. Make sure that
screws are installed in the original location they were removed from during reinstallation.
Fasteners used in M452 models

● M3x10mm Plastite (metallic)
● M3x8mm Taptite (metallic)
● M3x6mm Taptite (black)
Fasteners used in M377, M477 models

● M3x8mm Taptite (metallic)
● M3x6mm Taptite (black)
● M4x13.3mm Plastite (black chrome)
● M3x14 Taptite (black)
ENWW Removal and replacement strategy 5

Service approach
Before performing service
WARNING! Turn the printer off, wait 30 seconds, and then remove the power cord before attempting to
service the printer. If this warning is not followed, severe injury and damage to the printer can result. The
power must be on for certain functional checks during troubleshooting. However, the power supply should be
disconnected during parts removal.
1. Remove all paper.
2. Place the printer on an ESD mat (if available). If an ESD workstation or mat is not available, touch the
sheet-metal chassis to provide a static ground before touching an ESD-sensitive assembly.
3. Remove the toner cartridge or toner cartridges.
4. Remove the trays.
Secondary service menu

Use the secondary service menu to print service-related reports and to run special tests. Customers do not
have access to this menu.
Two-line control panels
1. From the printer control panel, press the OK button.
2. Select the Setup menu, and then press the OK button.
3. Press the left arrow button, and then quickly press the Cancel button. The control panel returns to
the Ready state.
4. Press the OK button, and then reopen the Setup menu.
5. Select the 2ndary Service menu, and then press the OK button.
Touchscreen control panels
1. From the Home screen on the printer control panel, swipe to and touch the Setup button.
2. Touch the space between the Home and Help control-panel buttons.
3. Touch the Back button. The control panel returns to the Home screen.
4. From the Home screen on the printer control panel, swipe to and touch the Setup button.
5. Touch the 2ndary Service menu.
After performing service
1. Reinstall the toner cartridge or toner cartridges.
2. Reinstall the trays.
3. Return all paper to the trays.

4. Plug in the power cable and turn on the printer.
5. Perform print-quality tests by printing from a host computer.
Post service tests

After service has been completed, perform the following tests to verify that the repair or replacement was
successful.
Print-quality test
1. Verify that you have completed the necessary reassembly steps.
2. Ensure that the input tray contains clean, unmarked paper.
3. With the power cord and interface cables attached, turn on the printer.
4. Verify that the expected start up sounds occur.
5. Print a configuration page, and then verify that the expected printing sounds occur.
6. Print a demo page, and then verify that the print quality is as expected.
7. Send a print job from the host computer, and then verify that the output meets expectations.
8. If necessary, restore any customer-specified settings.
9. Clean the outside of the printer with a damp cloth.
Copy-quality test (M377, M477 models)

1. Verify that you have completed the necessary reassembly steps.
2. Ensure that the input tray contains clean, unmarked paper.
3. With the power cord attached, turn on the printer.
4. Verify that the expected start up sounds occur.
5. Print a configuration page, and then verify that the expected printing sounds occur.
6. Place the configuration page in the document feeder or on the flatbed glass.
7. Print a copy job, and then verify the results.
8. Clean the outside of the printer with a damp cloth.
Fax-quality test (M477 models)

1. Place the configuration page in the document feeder.
2. Type a valid fax number, and send the fax job.
3. Verify that the send quality and the receive quality meet expectations.
ENWW Service approach 7

Order parts by authorized service providers
Order supplies and paper www.hp.com/go/suresupply
Order genuine HP parts or accessories www.hp.com/buy/parts
Order through service or support providers Contact an HP-authorized service or support provider.
Order using the HP Embedded Web Server (EWS) To access, in a supported Web browser on your computer, enter
the printer IP address or host name in the address/URL field. The
EWS contains a link to the HP SureSupply Web site, which provides
options for purchasing Original HP supplies.
Orderable parts
Not all of the assemblies described in this chapter can be ordered. Use the parts chapter in this manual to
determine if an assembly is orderable.
Whole unit replacement (WUR) part numbers

Part number Description
CF388-67056 220V M452nw WUR CN
CF388-69001 220V M452nw WUR EMEA
CF388-69002 220V M452nw WUR AP
CF388-69003 110V M452nw WUR WW
CF389-67056 220V M452dn WUR CN
CF389-69001 220V M452dn WUR WW
CF389-69002 220V M452dn WUR AP
CF389-69003 110V M452dn WUR WW
CF394-67056 220V M452dw WUR CN
CF394-69001 220V M452dw WUR LAC
CF394-69002 220V M452dw WUR AP
CF394-69003 110V M452dw WUR WW
CF377-67055 110V M477fnw WUR BR
CF377-67056 220V M477fnw WUR CN/MY
CF377-69001 220V M477fnw WUR EMEA
CF377-69002 110V M477fnw WUR NAR/TW
CF377-69003 220V M477fnw WUR AP/LAR
CF377-69004 220V M477fnw WUR CL/AR
CF378-69001 220V M477fdn WUR EMEA
CF378-69002 110V M477fdn WUR NAR/TW
CF379-67055 110V M477fdw WUR BR

Part number Description
CF379-67056 220V M477fdw WUR CN/MY
CF379-69001 220V M477fdw WUR EMEA
CF379-69002 110V M477fdw WUR NAR/TW
CF379-69003 220V M477fdw WUR AP/LAR
CF379-69004 220V M477fdw WUR CL/AR
M5H23-67001 220V M377dw WUR CN/MY
M5H23-69001 220V M377dw WUR EMEA
M5H23-69002 220V M377dw WUR AP/LAR
M5H23-69003 110V M377dw WUR NAR/TW
Supplies part numbers

Table 1-1 Supplies part numbers
Item Description Cartridge number Part number
Supplies
HP 410A Black Original LaserJet Toner Standard-capacity replacement black toner 410A CF410A
Cartridge cartridge
HP 410X High Yield Black Original High-capacity replacement black toner 410X CF410X
LaserJet Toner Cartridge cartridge
HP 410A Cyan Original LaserJet Toner Standard-capacity replacement cyan toner 410A CF411A
Cartridge cartridge
HP 410X High Yield Cyan Original High-capacity replacement cyan toner 410X CF411X
HP 410A Yellow Original LaserJet Standard-capacity replacement yellow toner 410A CF412A
Toner Cartridge cartridge
HP 410X High Yield Yellow Original High-capacity replacement yellow toner 410X CF412X
HP 410A Magenta Original LaserJet Standard-capacity replacement magenta 410A CF413A

Toner Cartridge toner cartridge
HP 410X High Yield Magenta Original High-capacity replacement magenta toner 410X CF413X
Accessories
Optional 550-sheet paper feeder Optional Tray 3 CF404A
USB 2.0 printer cable A-to-B cable (2-meter standard) C6518A
Related documentation and software

HP service personnel, go to the Link Service Access Work Bench (SAW) at
http://h41302.www4.hp.com/km/saw/home.do.
ENWW Order parts by authorized service providers 9

Channel partners, go to Link HP Channel Services Network (CNS) at https://h30125.www3.hp.com/hpcsn.

Removal and replacement procedures
Customer self-repair (CSR) A parts and assemblies
● Removal and replacement: Toner cartridges
● Removal and replacement: Trays
The CSR level indicates the expected difficulty the customer will experience when removing and replacing an
assembly. The CSR A assemblies in this section are easy for the customer to remove and replace.
ENWW Removal and replacement procedures 11

Removal and replacement: Toner cartridges
Introduction
This document provides the procedures to remove and replace the toner cartridges.
CAUTION: To prevent damage to a toner cartridge, do not expose it to light for more than a few minutes.
Cover the green imaging drum if the toner cartridge must be removed from the printer for an extended period
of time.
If toner gets on clothing, wipe it off by using a dry cloth and wash the clothes in cold water. Hot water sets
toner into fabric.
Use the table below to identify the correct part number for your printer. To order the part, go to
www.hp.com/buy/parts.
Toner cartridge part numbers
CF410-67901 Standard-capacity replacement black toner cartridge
CF410-67902 High-capacity replacement black toner cartridge
CF411-67901 Standard-capacity replacement cyan cartridge
CF411-67902 High-capacity replacement cyan toner cartridge
CF412-67901 Standard-capacity replacement yellow toner cartridge
CF412-67902 High-capacity replacement yellow toner cartridge
CF413-67901 Standard-capacity replacement magenta toner cartridge
CF413-67902 High-capacity replacement magenta toner cartridge
Required tools
No special tools are required to install this part.
Make sure that the cartridge tray and front door are fully closed after replacing a toner cartridge.
Post service test
The print quality page shows bands of colors that can indicate whether the printer is producing colors
correctly.
1. 2-line control panels: On the printer control panel, press the OK button.
Touchscreen control panels: From the Home screen, touch the Setup button.
2. Open the Reports menu.
3. Select the Print Quality Page menu item.

Step 1: Remove the toner cartridges
NOTE: The M452 model is pictured in the figures in this section. The procedure is the same for the M477
model.
1. Open the front door by pressing the button on the left cover.
Figure 1-2 Open the front door
2. Grasp the blue handle on the toner cartridge tray, and then pull out the tray.
Figure 1-3 Open the cartridge drawer

3. Grasp the handle on the toner cartridge, and then pull the toner cartridge straight up to remove it.
Figure 1-4 Remove the toner cartridge
Step 2: Unpack the replacement part
Remove the new toner cartridge from its protective shell by tearing off the plastic strip and opening the
package. Save all packaging for recycling the used toner cartridge.
Product return and recycling
CAUTION: To prevent damage to a replacement toner cartridge, do not expose it to light for more than a few
minutes. Cover the green imaging drum if the toner cartridge must be removed from the printer for an
extended period of time.
If toner gets on clothing, wipe it off by using a dry cloth and wash the clothes in cold water. Hot water sets
toner into fabric.
NOTE: HP recommends responsible disposal of the defective assembly.
Figure 1-5 Recycle and unpack
2 3

Step 3: Install a toner cartridge
1. Hold both ends of the toner cartridge and rock it 5-6 times.
Figure 1-6 Rock the toner cartridge
2. Do not touch the imaging drum on the bottom of the toner cartridge. Fingerprints on the imaging drum
can cause print-quality problems.
Figure 1-7 Do not touch imaging drum

3. Insert the new toner cartridge into the tray. Make sure that the color chip on the cartridge matches the
color chip on the tray.
Figure 1-8 Install a toner cartridge
4. Close the toner cartridge tray.
Figure 1-9 Close the toner cartridge drawer

5. Close the front door.
Figure 1-10 Close the front door

Removal and replacement: Trays
● Removal and replacement: Tray 2
● Removal and replacement: Tray 3

Removal and replacement: Tray 2
● Introduction
● Step 1: Remove Tray 2
● Step 2: Unpack the replacement part
● Step 3: Install Tray 2
Introduction
This document provides the procedures to remove and replace Tray 2.
Use the table below to identify the correct part number for your printer, and then go to
http://h20141.www2.hp.com/hpparts to order the part.
Tray 2 part number
RM2-6377-000CN Tray 2
Required tools
Make sure that Tray 2 is fully closed after replacing it.
Step 1: Remove Tray 2

▲ Pull the tray out until it stops. Lift the front of the tray, and then pull it out of the printer to remove it.
Figure 1-11 Remove the tray
Remove the new part from its package. Save all packaging for recycling the used part.

For complete information on HP's recycling programs, go to Product return and recycling.
NOTE: HP recommends responsible disposal of the defective part.
Step 3: Install Tray 2

▲ With the front of the tray slightly lifted, align the sides of the tray with the rails in the printer, and then
carefully slide the tray into the printer. As the tray slides into the printer, lower the front of the tray, and
then close it.
Figure 1-13 Install the tray

Removal and replacement: Tray 3
● Introduction
● Step 1: Remove the tray
● Step 2: Unpack the replacement tray
● Step 3: Install the tray
Introduction
This document provides the procedures to remove and replace Tray 3.
Use the table below to identify the correct part number for your printer, and then go to
http://h20141.www2.hp.com/hpparts to order the part.
Tray 3 part number
RM2-6486-000CN Tray 3
Required tools
Make sure that Tray 3 is fully closed after replacing it.
Step 1: Remove the tray


Step 2: Unpack the replacement tray
Step 3: Install the tray

▲ With the front of the tray slightly lifted, align the sides of the tray with the rails in the feeder, and then
carefully slide the tray into the feeder. As the tray slides into the feeder, lower the front of the tray, and
then close it.

Field replaceable units (FRUs)
Removal and replacement: Rollers
● Removal and replacement: Tray 1 pickup roller
● Removal and replacement: Tray 1 separation pad
● Removal and replacement: Tray 2 pickup and feed rollers
● Removal and replacement: Tray 2 separation roller
● Removal and replacement: Tray 3 pickup and feed rollers
● Removal and replacement: Tray 3 separation roller
● Removal and replacement: Secondary transfer roller

Removal and replacement: Tray 1 pickup roller
● Introduction
● Step 1: Open the front door
● Step 2: Remove the Tray 1 pickup roller
● Step 4: Install the Tray 1 pickup roller
● Step 5: Close the front door
Introduction
This document provides the procedures to remove and replace the Tray 1 pickup roller.
Before you begin

● Turn off the printer.
● Disconnect the power cable.
WARNING! To avoid damage to the printer, turn the printer off, wait 30 seconds, and then remove the
power cord before attempting to service the printer.
● Use the table below to identify the correct part number for your printer. To order the part, go to
www.hp.com/buy/parts to order the part.
Tray 1 pickup roller part number
RL1-2593-000CN Tray 1 pickup roller
Required tools

● Connect the power cable.
● Use the power switch to turn the power on.
Step 1: Open the front door
1. Press the button (callout 1) on the left side of the printer to release the front door.

Figure 1-17 Release the front door
2. Open the front door.
Step 2: Remove the Tray 1 pickup roller
1. Release two tabs (callout 1).

Figure 1-19 Release two tabs
2. Remove the pickup roller.
Figure 1-20 Remove the pickup roller
Remove the new pickup roller from its package. Save all packaging for recycling the used parts.

Step 4: Install the Tray 1 pickup roller

▲ Position the tabs (callout 1) on the roller into the slots (callout 2) on the roller shaft. Press down to snap
the roller into place.
Figure 1-22 Install the pickup roller
Step 5: Close the front door

▲ Close the front door.


Removal and replacement: Tray 1 separation pad
● Introduction
● Step 1: Open the front door
● Step 2: Remove the Tray 1 separation pad
● Step 4: Install the Tray 1 separation pad
● Step 5: Close the front door
Introduction
This document provides the procedures to remove and replace the Tray 1 separation pad.
Before you begin

Tray 1 separation pad part number
RM2-6406-000CN Tray 1 separation pad
Required tools

Step 1: Open the front door

Step 2: Remove the Tray 1 separation pad
1. Press down on the separation pad holder (callout 1) and release two tabs (callout 2).

Figure 1-26 Press down and release tabs
2. Continue to press down on the separation pad holder (callout 1), and the slide the separation pad
(callout 2) away from the printer to remove it.
Figure 1-27 Remove the separation pad
Remove the new separation roller from its package. Save all packaging for recycling the used part.
For complete information on HP's recycling programs, go to Product return and recycling

Step 4: Install the Tray 1 separation pad
1. Press down on the separation pad holder (callout 1), and then slide the separation pad (callout 2) toward
the printer to install it.
Figure 1-29 Position the separation pad

2. Press down on the separation pad (callout 1) until the two tabs (callout 2) snap into place.
Figure 1-30 Snap the separation pad into place
Step 5: Close the front door

▲ Close the front door.

Removal and replacement: Tray 2 pickup and feed rollers
● Introduction
● Step 1: Remove the toner cartridges
● Step 3: Remove the Tray 2 pickup or feed roller
● Step 5: Install the Tray 2 pickup or feed roller
● Step 7: Install the toner cartridges
Introduction
This document provides the procedures to remove and replace the Tray 2 pickup and feed rollers.
Before you begin

Tray 2 pickup and feed rollers part numbers
RM2-5576-000CN Tray 2 pickup roller
RM2-5577-000CN Tray 2 feed roller
Required tools
● No tools are required to install this part.

NOTE: The M452 model is pictured in the figures in this section. The procedure is the same for the M377,
M477 models.


Repeat this step for each toner cartridge.
4. Slide the cartridge tray into the printer.
Figure 1-35 Slide the cartridge tray in


Step 3: Remove the Tray 2 pickup or feed roller
1. Turn the printer right side up, so that it is resting on the left side. Press the release button (callout 1),
and then release the Tray 1 feed guide (callout 2) toward the front of the printer.

Figure 1-38 Release the feed guide
2. On the underside of the printer, press the tab (callout 1) toward the front of the printer, and then slide
the roller holder down (callout 2).
Figure 1-39 Release the roller holder
1
2

3. Remove the pickup and feed roller case (callout 1).
Figure 1-40 Remove the roller case
4. Locate the feed roller (callout 1) and the pickup roller (callout 2).
Figure 1-41 Locate the rollers
2
1

5. Release the top of the roller and remove it from the case.
NOTE: The feed roller is shown in the figure below. The procedure is the same for the pickup roller.
Figure 1-42 Remove the roller
Remove the part from its package. Save all packaging for recycling the used part.
Step 5: Install the Tray 2 pickup or feed roller
1. Install the ridge on the bottom of the roller (callout 1) in the hole in the bottom of the case (callout 2).

Figure 1-44 Position the roller
2. Rotate the top of the roller into the case. Make sure that the roller snaps into place.
Figure 1-45 Install the roller

3. Make sure that the printer is positioned right side up, so that it is resting on the left side. Install the ends
of the rollers (callout 1) in the roller case over the shafts (callout 2) on the printer.
Figure 1-46 Position the roller case
4. Hold the roller case in position (callout 1) and slide the roller holder (callout 2) up until it snaps into
place.
Figure 1-47 Install the roller case
2
5. Return the printer to an upright position so that the bottom side is down.

then close it.

Step 7: Install the toner cartridges

2. Slide the cartridge tray out of the printer.
Figure 1-50 Slide the cartridge tray out

4. Insert the toner cartridge into the tray. Make sure that the color chip on the cartridge matches the color
chip on the tray. Repeat this step for each toner cartridge.
5. Close the toner cartridge drawer.


Removal and replacement: Tray 2 separation roller
● Introduction
● Step 3: Remove the Tray 2 separation roller
● Step 5: Install the Tray 2 separation roller
Introduction
This document provides the procedures to remove and replace the Tray 2 separation roller.
Before you begin

Tray 2 separation roller part number
RM2-5881-000CN Tray 2 separation roller
Required tools

M477 models.




Step 3: Remove the Tray 2 separation roller
1. Turn the printer front side up, so that it is resting on the rear door or duplexer door. On the underside of
the printer, release two hinge tabs (callout 1), and then release two tabs (callout 2).

Figure 1-61 Release the tabs
2. Lift up to remove the separation roller cover.
Figure 1-62 Remove the cover

3. Press on the left side of the separation roller (callout 1) to release it.
Figure 1-63 Release the separation roller
4. Remove the separation roller (callout 1).
Figure 1-64 Remove the separation roller
Remove the part from its package. Save all packaging for recycling the used part.

Step 5: Install the Tray 2 separation roller
1. Make sure that the printer is positioned front side up, so that it is resting on the rear door or duplexer. On
the underside of the printer, position the end of the roller into the slot in the printer (callout 1). It might
be necessary to rotate the roller until it fits correctly into the slot (callout 2). Press down on the left side
of the roller (callout 3) until it snaps into place.
Figure 1-66 Install the separation roller
1
3

2. Position the roller cover (callout 1) over the roller.
Figure 1-67 Position the roller cover
3. Make sure that the hinge tabs (callout 1) and the tabs (callout 2) snap into place.

then close it.





Removal and replacement: Tray 3 pickup and feed rollers
● Introduction
● Step 2: Remove the Tray 3 pickup or feed roller
● Step 4: Install the Tray 3 paper pickup roller
Introduction
This document provides the procedures to remove and replace the Tray 3 pickup roller.
Before you begin

Tray 3 pickup and feed rollers part numbers
RM2-5576-000CN Tray 3 pickup roller
RM2-5577-000CN Tray 3 feed roller
Required tools



Step 2: Remove the Tray 3 pickup or feed roller
1. Press the tab (callout 1) toward the front of the feeder, and then slide the roller holder to the right
(callout 2).
Figure 1-77 Release the roller holder

2. Remove the pickup and feed roller case (callout 1).
Figure 1-78 Remove the roller case
3. Locate the feed roller (callout 1) and the pickup roller (callout 2).
Figure 1-79 Locate the rollers
2
1

4. Release the top of the roller and remove it from the case.
Figure 1-80 Remove the roller
Remove the new pickup roller from its package. Save all packaging for recycling the used parts.
Step 4: Install the Tray 3 paper pickup roller
1. Install the ridge on the bottom of the roller (callout 1) in the hole in the bottom of the case (callout 2).

Figure 1-82 Position the roller
2. Rotate the top of the roller into the case. Make sure that the roller snaps into place.
Figure 1-83 Install the roller

3. Install the ends of the rollers (callout 1) in the roller case over the shafts (callout 2) on the printer.
Figure 1-84 Position the roller case
1
2
4. Slide the roller holder (callout 1) to the left until it snaps into place.
Figure 1-85 Install the roller case

then close it.


Removal and replacement: Tray 3 separation roller
● Introduction
● Step 2: Remove the Tray 3 separation roller
● Step 4: Install the Tray 3 separation roller
Introduction
This document provides the procedures to remove and replace the Tray 3 separation roller.
Before you begin

Tray 3 separation roller kit part number
RM2-5881-000CN Tray 3 separation roller
Required tools



Step 2: Remove the Tray 3 separation roller
1. Release two tabs (callout 1), and then release two hinge tabs (callout 2).
Figure 1-88 Release the tabs

2. Lift up to remove the separation roller cover.
3. Press on the left side of the separation roller to release it.
Figure 1-90 Release the separation roller

4. Remove the separation roller (callout 1).
Figure 1-91 Remove the separation roller
Remove the new separation roller from its package. Save all packaging for recycling the used part.
Step 4: Install the Tray 3 separation roller
1. Position the end of the roller into the slot in the printer (callout 1). It might be necessary to rotate the
roller until it fits correctly into the slot. Press down on the left side of the roller (callout 2) until it snaps
into place.

Figure 1-93 Install the separation roller
2. Position the roller cover over the separation roller.
Figure 1-94 Position the roller cover

3. Install the roller cover. Make sure that the hinge tabs (callout 1) and the tabs (callout 2) snap into place.

then close it.

Removal and replacement: Secondary transfer roller
● Introduction
● Step 1: Remove the secondary transfer roller
● Step 2:Unpack the replacement part
● Step 3: Install the secondary transfer roller
Introduction
This document provides the procedures to remove and replace the secondary transfer roller.
Before you begin

Secondary transfer roller part number
RM2-6455-000CN Secondary transfer roller
Required tools

Step 1: Remove the secondary transfer roller
1. For simplex models (M452nw and M477fnw) open the rear cover. For duplex models (M377dw, M452dn,
M452dw, M477fdn, and M477fdw), open the duplex door assembly. Inside the door assembly, release
two tabs (callout 1).

2. Lift up the left end of the roller.
Figure 1-98 Lift the end of the roller

3. Remove the stopper (callout 1) from the end of the roller (callout 2).
Figure 1-99 Remove the stopper
2
1
NOTE: If the spring falls off of the stopper, reattach it as shown below.
Figure 1-100 Reattach the stopper spring

4. Remove the secondary transfer roller.
Figure 1-101 Remove the secondary transfer roller
Step 2:Unpack the replacement part
Remove the new secondary transfer roller from its package. Save all packaging for recycling the used part.
Step 3: Install the secondary transfer roller
1. Position the end of the secondary transfer roller into the slot in the holder (callout 1).

Figure 1-103 Position the secondary transfer roller
2. Position the metal shaft (callout 1) on the end of the roller into the opening (callout 2) in the stopper.
Figure 1-104 Attach stopper
2
1

3. Lower the secondary transfer roller and stopper into position.
Figure 1-105 Install the secondary transfer roller
4. Make sure that two tabs (callout 1) snap into place. Close the rear cover or the duplex door assembly.
Figure 1-106 Check the tabs

Removal and replacement: External panels, covers, and doors
● Removal and replacement: Right cover (M452 models)
● Removal and replacement: Left cover (M452 models)
● Removal and replacement: Right cover (M377, M477 models)
● Removal and replacement: Left cover (M377, M477 models)
● Removal and replacement: Front door assembly
● Removal and replacement: Duplexer door assembly (duplex models)
● Removal and replacement: Rear top cover (simplex models)
● Removal and replacement: Rear lower cover (simplex models)
● Removal and replacement: Rear door (simplex models)
● Removal and replacement: Top cover (M452 models)
● Removal and replacement: Top cover (M377, M477 models)
● Removal and replacement: Touchscreen control panel (M452dw model)
● Removal and replacement: Touchscreen control panel (M377, M477 models)

Removal and replacement: Right cover (M452 models)
● Introduction
● Step 2: Open the front door and rear door or duplexer door
● Step 3: Remove the right cover
● Step 5: Install the right cover
● Step 6: Close the front door and rear door or duplexer door
Introduction
This document provides the procedures to remove and replace the right cover for the M452.
Before you begin

Right cover part number (M452 models)
RC4-4853-000CN Right cover (M452 models)
Required tools
● #2 Phillips screwdriver with a magnetic tip



Step 2: Open the front door and rear door or duplexer door

3. Duplex models: Open the duplexer door.
Figure 1-110 Open the duplexer door

4. Simplex models: Open the rear door.
Figure 1-111 Open the rear door
Step 3: Remove the right cover
1. At the back of the printer, remove one screw (callout 1).
Figure 1-112 Remove one screw

2. At the front of the printer, remove one screw (callout 1).
3. Slide the printer to the edge of a work surface. Note the location of the tabs on the lower edge of the
cover (callout 1).
Figure 1-114 Locate the tabs

4. Release one tab (callout 1) on the front of the cover by slightly pulling the cover away from the printer.
While holding the cover in the released position, release one tab (callout 2) on the bottom of the cover.
Figure 1-115 Release front lower tabs
1
2
5. Hold the front tabs in the released position (callout 1), and then release one tab (callout 2) on the
bottom of the cover, toward the back of the printer.
Figure 1-116 Release lower rear tab

6. Release two tabs at the front of the printer (callout 1) by slightly pulling the cover away from the printer.
CAUTION: Be careful not to dislodge the power switch (callout 2).
Figure 1-117 Release two front tabs
1
2
7. Release four tabs on the top of the printer (callout 1).
Figure 1-118 Release upper tabs

8. Slide the cover toward the back of the printer to remove it.
Figure 1-119 Remove the right cover
Step 5: Install the right cover
1. Position two tabs (callout 1) on the back of the cover in the slots (callout 2) in the printer.

Figure 1-121 Position two tabs
2
1
2. At the back of the printer, install the tab (callout 1) under the edge of the top cover (callout 2).
Figure 1-122 Install rear tab

3. Slide the cover toward the front of the printer to install it.
Figure 1-123 Install the right cover
4. Engage three tabs (callout 2) on the top of the cover.
Figure 1-124 Install upper tabs

5. At the front of the printer, position the front of the cover over two tabs (callout 1).
Figure 1-125 Install the front tabs
1
2
6. Press the right cover toward the printer to engage one tab (callout 1) on the front of the cover.
Figure 1-126 Install the front lower tab

7. Install two tabs on the bottom of the cover (callout 1).
Figure 1-127 Install two tabs
8. At the front of the printer, install one screw (callout 1).
Figure 1-128 Install one screw

9. At the back of the printer, install one screw (callout 1).
Step 6: Close the front door and rear door or duplexer door

2. Duplex models: Close the duplexer door.
Figure 1-131 Close the duplexer door
3. Simplex models: Close the rear door.
Figure 1-132 Close the rear door

then close it.


Removal and replacement: Left cover (M452 models)
● Introduction
● Step 3: Remove the left cover (M452 models)
● Step 5: Install the left cover (M452 models)
Introduction
This document provides the procedures to remove and replace the left cover for the M452.
Before you begin

Left cover part numbers
RC4-4854-000CN Left cover (M452 models)
Required tools





Step 3: Remove the left cover (M452 models)

2. Release two tabs (callout 1) at the front of the cover. Hold the cover open to prevent the tabs from
reengaging.
cover (callout 1).

4. Beginning from the front of the cover, release four tabs (callouts 1-4) on the lower edge of the cover.
Figure 1-142 Release bottom tabs
4 3 2 1
5. Release three tabs at the top of the cover (callout 1), and then slide the cover toward the rear of the
printer to remove it.
Figure 1-143 Release three tabs

6. On the inside of the left cover, release two tabs (callout 1).
7. Remove the door-release button. Save this button for installation on the replacement left cover.
Figure 1-145 Remove the button

Step 5: Install the left cover (M452 models)
1. Install the door-release button removed from the old left cover into the replacement left cover in the
orientation shown.
Figure 1-147 Install the button

2. Make sure that the two tabs (callout 1) snap into place.
3. Position the hook (callout 1) on the cover in the slot (callout 2) on the printer. Position three tabs
(callout 3) on the back of the cover in the slots (callout 4) in the printer.
Figure 1-149 Position three tabs
2
1
3 4

Figure 1-150 Install one tab

2

5. Slide the cover toward the front of the printer (callout 1), and then engage three tabs (callout 2) on the
top of the cover.
Figure 1-151 Install the left cover
CAUTION: Make sure that the tab (callout 1) does not get caught behind the printer frame (callout 2).
Figure 1-152 Make sure the tab does not get caught
2
1

6. Slide the printer to the edge of a work surface in order to access the tabs on the bottom of the cover.
Beginning from the back of the cover, install four tabs (callouts 1-4) on the lower edge of the cover.
Figure 1-153 Install four tabs
1 2 3 4
7. Install two tabs (callout 1) at the front of the cover.
Figure 1-154 Engage two tabs

8. Make sure that the hinge pin (callout 1) on the front door fits into the slot (callout 2) on the left cover.
Figure 1-155 Install hinge pin
1
2
9. Install one screw (callout 1).



then close it.

Removal and replacement: Right cover (M377, M477 models)
● Introduction
● Step 3: Remove the right cover
● Step 4: Unpack a replacement right cover
● Step 5: Install the right cover
Introduction
This document provides the procedures to remove and replace the right cover for the M377, M477.
Before you begin

Right cover part number (M377, M477 models)
RC4-6044-000CN Right cover (M377, M477 models)
Required tools





Step 3: Remove the right cover
1. Raise the scanner.
Figure 1-166 Raise the scanner


cover (callout 1).
While holding the cover in the released position, release one tab (callout 2) on the lower edge of the
cover.
1
2

6. Hold the front tabs in the released position (callout 1), and then release one tab (callout 2) on the lower
edge of the cover, toward the back of the printer.
Figure 1-172 Release front upper tabs

8. Rotate the front of the cover away from the printer (callout 1).
Figure 1-173 Rotate the front of the cover
9. Slightly pull the front of the cover away from the printer (callout 1) to release one tab (callout 2).
Figure 1-174 Release top tabs

10. At the top of the printer, slightly pull the top of the cover away from the printer to release one retention
tab (callout 1) on the inside of the cover. While holding the cover away, slide the cover toward the back of
the printer (callout 2) to release one hook (callout 3) on the inside of the cover.
Figure 1-175 Release one tab and one hook
11. Lower the scanner.
Figure 1-176 Lower the scanner

12. Rotate the cover away from the printer (callout 1) to release one tab (callout 2) at the back of the printer,
and then remove the cover.
Step 4: Unpack a replacement right cover
Step 5: Install the right cover
1. At the back of the printer, install the tab (callout 1) on the cover into the slot (callout 2) on the printer.

2
1

3. Rotate the right cover toward the printer.
Figure 1-181 Rotate the right cover
4. Position the hooks (callout 1) on the inside of the cover into the slots (callout 2) in the printer.
Figure 1-182 Position the hooks in the slots

5. Engage one hook (callout 1) on the inside of the cover. Hold the top of the cover closed (callout 2) while
sliding the cover toward the front of the printer (callout 3).
Figure 1-183 Slide the cover
1
2
6. Rotate the front of the cover toward the printer (callout 1).

7. Install two tabs at the front of the printer (callout 1).
8. Press the right cover toward the printer (callout 1) to engage one tab on the front of the cover, and two
tabs (callout 2) on the lower edge of the cover.
Figure 1-186 Install the front and lower tabs




then close it.


Removal and replacement: Left cover (M377, M477 models)
● Introduction
● Step 3: Remove the left cover
● Step 5: Install the left cover
Introduction
This document provides the procedures to remove and replace the left cover for the M377, M477.
Before you begin

Left cover part numbers
RC4-6045-000CN Left cover (M377, M477 models)
Required tools





Step 3: Remove the left cover

3. Release two tabs (callout 1) at the front of the cover. Hold the cover open to prevent the tabs from re-
engaging.

cover (callout 1).
5. Beginning from the front of the cover, release the four tabs (callouts 1-4) on the lower edge of the cover.
Figure 1-203 Release four tabs
4 3
2 1

6. Rotate the front of the cover away from the printer (callout 1). Make sure that the tab (callout 2) does
not get caught on the printer frame (callout 3).
Figure 1-204 Rotate the cover
3
1
the printer (callout 2) to release two hooks (callout 3) inside the cover.
Figure 1-205 Release one tab and two hooks

9. Rotate the cover away from the printer (callout 1), and then slide the cover (callout 2) toward the back of
the printer to remove it.
Figure 1-207 Remove the left cover
2 1

10. On the inside of the left cover, release two tabs (callout 1).
11. Remove the door-release button. Save this button for installation on the replacement left cover.
Figure 1-209 Remove the button

Step 5: Install the left cover
1. Install the door-release button removed from the old left cover into the replacement left cover in the
orientation shown.
Figure 1-211 Install the button

2. Make sure that the two tabs (callout 1) snap into place.
3. At the back of the printer, install the tab (callout 1) on the cover into the slot (callout 2) in the printer.
Install the locator pins (callout 3) into the slots (callout 4) in the printer.
2
1
3 4

4. Rotate the cover toward the printer.
Figure 1-214 Rotate the left cover

6. Position the hooks (callout 1) on the inside of the cover into the slots (callout 2) on the printer.

7. Hold the cover against the printer (callout 1), and then slide it (callout 2) toward the front of the printer.
Figure 1-218 Install the top hooks
CAUTION: Make sure that the tab (callout 1) on the front of the cover does not get caught behind the
printer frame (callout 2).

1 2
3 4
9. Press the cover toward the printer (callout 1), and then install two tabs (callout 2) at the front of the
cover.
1
2

1
2



then close it.


Removal and replacement: Front door assembly
● Introduction
● Step 3: Remove the right cover (M452 models)
● Step 4: Remove the right cover (M377, M477 models)
● Step 5: Remove the front door assembly
● Step 7: Install the front door assembly
● Step 8: Install the right cover (M452 models)
● Step 9: Install the right cover (M377, M477 models)
Introduction
This document provides the procedures to remove and replace the front door.
Before you begin

Front door part numbers
RM2-6390-000CN Front door assembly
Required tools
● Small flat-blade screwdriver




Step 3: Remove the right cover (M452 models)
NOTE: This step is for the M452 models. For the M377, M477 models, skip this step and go to Step 4:
Remove the right cover (M377, M477 models) on page 153.

cover (callout 1).

1
2

1
2

Step 4: Remove the right cover (M377, M477 models)
NOTE: This step is for the M377, M477 models. For the M452 models, skip this step and go to Step 5:
Remove the front door assembly on page 159.


cover (callout 1).
cover.
1
2




Step 5: Remove the front door assembly
1. Remove one screw (callout 1).

2. Tilt the front door up to about a 45-degree angle.
Figure 1-255 Tilt the door up
3. Lift the end of the right hinge cover up (callout 1), and then slide it away from the door (callout 2) to
disconnect it.
Figure 1-256 Release the right hinge cover

4. On the left side of the door, release one tab (callout 1).
Figure 1-257 Release one tab
5. Release the left hinge cover (callout 1).
Figure 1-258 Release the left hinge cover

7. Release one arm (callout 1).
Figure 1-260 Release one arm

8. Lift the front door up slightly, swing the right side of the door away from the printer (callout 1), and then
slide the door left (callout 2) to remove it.
Figure 1-261 Remove the front door
1
2
Step 7: Install the front door assembly
1. Install the hinge on the left side of the door, and then slide the door left (callout 1). Rotate the right side
of the door (callout 2) toward the printer.

Figure 1-263 Install the front door
2
1
2. Install the tab on the end of the arm (callout 1) into the slot (callout 2) in the printer.
Figure 1-264 Install one arm
1
2

4. If the left hinge cover becomes detached, reattach it as shown below.
Figure 1-266 Attach left hinge cover

5. Press down to reinstall the left hinge cover (callout 1).
Figure 1-267 Install the left hinge cover
6. If the right hinge cover becomes detached, reattach it as shown below.
Figure 1-268 Attach right hinge cover

7. Install the tab (callout 1) on the hinge cover in the slot (callout 2) on the front door, and then rotate
(callout 3) the cover down toward the door.
Figure 1-269 Install the hinge cover
1
3
Step 8: Install the right cover (M452 models)
NOTE: This step is for the M452 models. For the M377, M477 models, skip this step and go to Step 9: Install
the right cover (M377, M477 models) on page 172.

2
1


1
2


Step 9: Install the right cover (M377, M477 models)
NOTE: This step is for the M377, M477 models. For the M452 models, skip this step and go to Step 10: Close
the front door and rear door or duplexer door on page 177.
2
1


1
2






then close it.

Removal and replacement: Duplexer door assembly (duplex models)
● Introduction
● Step 2: Open the front door and duplexer door
● Step 6: Remove the left cover (M377, M477 models)
● Step 7: Remove the duplexer door assembly
● Step 9: Install the duplexer door assembly
● Step 11: Install the left cover (M377, M477 models)
● Step 14: Close the front door and duplexer door
Introduction
This document provides the procedures to remove and replace the duplexer door for duplex models.
Before you begin

Duplexer door part number
RM2-6383-000CN Duplexer door
Required tools


Step 2: Open the front door and duplexer door

3. Open the duplexer door.


cover (callout 1).
1
2

2
1
2

Remove the left cover (M452 models) on page 192.


cover (callout 1).

cover.
1
2



Remove the left cover (M377, M477 models) on page 195.

reengaging.

cover (callout 1).
4 3 2 1

Step 6: Remove the left cover (M377, M477 models)
Remove the duplexer door assembly on page 199.

engaging.

cover (callout 1).
4 3
2 1

3
1

2 1
Step 7: Remove the duplexer door assembly
1. Rotate the secondary transfer assembly (callout 1) toward the printer to close it.

Figure 1-333 Close the secondary transfer assembly
2. At the back of the printer, remove two screws (callout 1), and then remove one screw (callout 2) that
holds the retention arm.
Reinstallation tip: Note that the screw (callout 2) that holds the retention arm is longer than the other
two. Make sure this screw is installed in the correct position.
Figure 1-334 Remove three screws

3. Release the retention arm (callout 1).
Figure 1-335 Release the retention arm
4. Release one tab (callout 1), and then slide the duplexer door (callout 2) to the right to remove it.
Figure 1-336 Remove the duplexer door

Step 9: Install the duplexer door assembly
1. Position the tab (callout 1) on the door into the slot (callout 2) on the printer.
Figure 1-338 Position the tab in the slot
2
1

2. Slide the door to the left (callout 1) until the tab (callout 2) snaps into place.
Figure 1-339 Install the duplexer door
3. Install the tabs (callout 1) on the retaining arm into the slots (callout 2) in the printer.
Figure 1-340 Install the retaining arm
2
1

4. At the back of the printer, install two screws (callout 1), and then install one screw (callout 2) that holds
the retention arm.
Figure 1-341 Install three screws
Install the left cover (M377, M477 models) on page 208.
2
1
3 4


2

top of the cover.
2
1

1 2 3 4

1
2
Step 11: Install the left cover (M377, M477 models)
Install the right cover (M452 models) on page 215.

2
1
3 4




1 2
3 4
cover.
1
2

1
2

Install the right cover (M377, M477 models) on page 219.
2
1


1
2


the front door and duplexer door on page 225.

2
1


1
2



Step 14: Close the front door and duplexer door

2. Close the duplexer door.

then close it.

Removal and replacement: Rear top cover (simplex models)
● Introduction
● Step 2: Open the front door and rear door
● Step 7: Remove the rear top cover
● Step 9: Install the rear top cover
● Step 14: Close the front door and rear door
Introduction
This document provides the procedures to remove and replace the rear top cover for simplex models.
Before you begin

Rear top cover part number
RC4-4855-000CN Rear top cover
Required tools


Step 2: Open the front door and rear door

3. Open the rear door.


cover (callout 1).
1
2

2
1
2



cover (callout 1).

cover.
1
2




reengaging.

cover (callout 1).
4 3 2 1

Remove the rear top cover on page 246.

engaging.

cover (callout 1).
4 3
2 1

3
1

2 1
Step 7: Remove the rear top cover
1. At the back of the printer, release four tabs (callout 1) on the bottom of the cover and two tabs
(callout 2) on the top of the cover.

Figure 1-423 Release six tabs
2. Remove the rear top cover.
Figure 1-424 Remove the rear top cover

Step 9: Install the rear top cover
1. Position the tabs on top of the rear top cover (callout 1) under the edge of the top cover (callout 2).
Figure 1-426 Install the rear top cover

2. Make sure that the tabs on the bottom (callout 1) and the tabs on the top (callout 2) snap into place.
2
1
3 4


2

top of the cover.
2
1

1 2 3 4

1
2

2
1
3 4




1 2
3 4
cover.
1
2

1
2

2
1


1
2


the front door and rear door on page 270.

2
1


1
2



Step 14: Close the front door and rear door

2. Close the rear door.

then close it.

Removal and replacement: Rear lower cover (simplex models)
● Introduction
● Step 7: Remove the rear lower cover (simplex models)
● Step 9: Install the rear lower cover (simplex models)
Introduction
This document provides the procedures to remove and replace the rear lower cover for simplex models.
Before you begin

Rear lower cover part number
RC4-5131-000CN Rear lower cover
Required tools



NOTE: This step is for the M452 models. For the M477 models, skip this step and go to Step 4: Remove the
right cover (M477 models) on page 278.


cover (callout 1).
1
2

2
1
2

left cover (M452 models) on page 284.


cover (callout 1).

cover.
1
2




reengaging.

cover (callout 1).
4 3 2 1

rear lower cover (simplex models) on page 291.

engaging.

cover (callout 1).
4 3
2 1

3
1

2 1
Step 7: Remove the rear lower cover (simplex models)

2. Remove two screws (callout 1) and release one tab (callout 2).
Figure 1-510 Remove two screws and release one tab

3. Slide the printer to the edge of a work surface in order to allow removal of the cover. Lift the rear door
up (callout 1), and then move the rear lower cover down to remove it (callout 2).
Figure 1-511 Remove the rear lower cover
Step 9: Install the rear lower cover (simplex models)
1. Slide the printer to the edge of a work surface in order to allow installation of the cover. Lift the rear
door up (callout 1), and then move the rear lower cover up to install it (callout 2).

Figure 1-513 Install the rear lower cover
2. Engage one tab (callout 1), and then install two screws (callout 2).
Figure 1-514 Engage tab and install screws
NOTE: This step is for the M452 models. For the M477 models, skip this step and go to Step 11: Install the

2
1
3 4

2

top of the cover.
2
1

1 2 3 4

1
2

2
1
3 4




1 2
3 4
cover.
1
2

1
2

2
1


1
2


NOTE: This step is for the M477 models. For the M452 models, skip this step and go to Step 14: Close the
front door and rear door on page 315.

2
1


1
2





then close it.

Removal and replacement: Rear door (simplex models)
● Introduction
● Step 7: Remove the rear lower cover (simplex models)
● Step 8: Remove the rear door (simplex models)
● Step 10: Install the rear door (simplex models)
● Step 11: Install the rear lower cover (simplex models)
Introduction
This document provides the procedures to remove and replace the rear door for simplex models.
Before you begin

Rear door part number
RC4-5130-000CN Rear door

Required tools





cover (callout 1).

1
2

1
2



cover (callout 1).
cover.
1
2





reengaging.
cover (callout 1).

4 3 2 1
rear lower cover (simplex models) on page 337.


engaging.
cover (callout 1).

4 3
2 1
3
1


2 1
Step 7: Remove the rear lower cover (simplex models)

2. Remove two screws (callout 1) and release one tab (callout 2).
3. Slide the printer to the edge of a work surface in order to allow removal of the cover. Lift the rear door
up (callout 1), and then move the rear lower cover down to remove it (callout 2).
Figure 1-598 Remove the rear lower cover
Step 8: Remove the rear door (simplex models)

▲ Slightly flex one hinge arm (callout 1) to release a hinge pin, and then slide the rear door to the left
(callout 2) to remove it.

Figure 1-599 Remove the rear door
Step 10: Install the rear door (simplex models)

▲ Slightly flex the door hinge arms to install two hinge pins (callout 1).

Figure 1-601 Install the rear door
Step 11: Install the rear lower cover (simplex models)
1. Slide the printer to the edge of a work surface in order to allow installation of the cover. Lift the rear
door up (callout 1), and then move the rear lower cover up to install it (callout 2).
Figure 1-602 Install the rear lower cover

2. Engage one tab (callout 1), and then install two screws (callout 2).
2
1
3 4


2

top of the cover.
2
1

1 2 3 4

1
2

2
1
3 4




1 2
3 4
cover.
1
2

1
2

2
1


1
2



2
1


1
2





then close it.

Removal and replacement: Top cover (M452 models)
● Introduction
● Step 5: Remove the rear top cover (simplex model)
● Step 6: Remove the top cover (M452 models)
● Step 7: Remove the control panel (M452dw model)
● Step 9: Install the control panel (M452dw model)
● Step 10: Install the wireless antenna (M452nw/dw models)
● Step 11: Install the top cover (M452 models)
● Step 12: Install the rear top cover (simplex model)
Introduction
This document provides the procedures to remove and replace the top cover for the M452.
Before you begin

IMPORTANT: M452nw and M452dw models: Make sure to order a replacement antenna from the table
below when replacing the top cover. This new antenna must be installed on the replacement top cover.
Top cover part numbers
RM2-6433-000CN Top cover (M452nw)
RM2-6442-000CN Top cover (M452dn)

RM2-6456-000CN Top cover (M452dw)
0960-3467 Remote antenna
Required tools






cover (callout 1).
1
2

2
1
2


reengaging.

cover (callout 1).
4 3 2 1

Step 5: Remove the rear top cover (simplex model)

Step 6: Remove the top cover (M452 models)
1. M452dw model only: On the left side of the printer, on the formatter, disconnect one connector
(callout 1).
Figure 1-667 Disconnect one connector

2. M452nw/dn models only: On the left side of the printer, on the formatter, disconnect one connector
(callout 1).
3. M452nw/dw models only: Disconnect the antenna (callout 1) from the connector (callout 2) on the
wireless PCA.
Figure 1-669 Disconnect the antenna
1
2

4. M452dw model only: Remove one screw (callout 1) and release one ground wire. Remove one screw
(callout 2). Note the location (callout 3) of the guide.
Figure 1-670 Remove two screws
2 3 1
5. M452dw model only: Remove the guide.
Figure 1-671 Remove the guide

6. M452dn/dw models only: At the back of the printer, remove three screws (callout 1).
7. M452dn/dw models only: Gently pull the top of the fuser away (callout 1), and then release two tabs
(callout 2).

8. M452nw model only: At the back of the printer, remove one screw (callout 1), and then release two tabs
(callout 2).
Figure 1-674 Remove screw and release two tabs
9. At the front of the printer, remove two screws (callout 1), and then release one tab (callout 2).

10. Remove the top cover.
Figure 1-676 Remove the top cover
Step 7: Remove the control panel (M452dw model)
1. On the underside of the top cover, remove three screws (callout 1), and then carefully unfasten the tape
strips (callout 2) to unroute the control-panel flat cable.
TIP: HP recommends keeping the tape strips for reuse when the control panel is reinstalled.
Figure 1-677 Remove three screws and unroute cable

2. Lift up on the bracket (callout 1) to remove it.
Figure 1-678 Remove the bracket
3. Rotate the control panel away from the top cover.
Figure 1-679 Rotate the control panel

4. Pull the control panel away from the top side of the top cover to remove it.
Figure 1-680 Remove the control panel
Step 9: Install the control panel (M452dw model)
1. On the top side of the top cover, set the control panel in place.

Figure 1-682 Set the control panel in place
2. On the underside of the top cover, install the bracket (callout 1).
Figure 1-683 Install the bracket

3. On the underside of the top cover, install three screws (callout 1), and then carefully fasten the tape
strips (callout 2) to affix the control-panel flat cable to the cover.
CAUTION: Ensure that the control-panel cable is securely fastened to the control panel and the top
cover. Pinching the cable between the cover and the chassis can damage the cable.
Figure 1-684 Install three screws and fasten the cable
Step 10: Install the wireless antenna (M452nw/dw models)
Unpack the wireless antenna from its packaging and install it following the procedure below.
1. On the back of the antenna at the top edge, peel the protective backing off of the adhesive strip.
Figure 1-685 Remove protective backing from adhesive strip

2. Position the antenna on the top cover, and then press along the top edge to make sure that the adhesive
strip is securely in place.
Figure 1-686 Install the top adhesive strip
3. Begin peeling the silver tape up and away from the protective backing.
Figure 1-687 Peel the silver tape up

4. Peel the silver tape (callout 1) all the way up, and then remove the protective backing (callout 2).
Figure 1-688 Remove the protective backing
1
2
5. Press the entire surface of the silver tape down to make sure it is securely attached to the top cover.
Figure 1-689 Press the silver tape

6. Position the tape over the antenna cable to hold it securely against the top cover.
NOTE: If the tape is missing, use a small piece of electrical tape to secure the antenna to the top cover
at the location shown.
Figure 1-690 Position the tape
7. Remove the protective cover (callout 1) from the end of the antenna cable.
Figure 1-691 Remove the protective cover
Step 11: Install the top cover (M452 models)
1. Position the top cover on top of the printer.

Figure 1-692 Position the top cover
2. At the front of the printer, engage one tab (callout 1), and then install two screws (callout 2).

3. M452nw model only: At the back of the printer, install two tabs (callout 1), and then install one screw
(callout 2).
NOTE: The M452dw model is shown. The procedure is correct for the M452nw model.
Figure 1-694 Install two tabs and one screw
4. M452dn/dw models only:Gently pull the top of the fuser away (callout 1), and then install two tabs
(callout 2).

5. M452dn/dw models only: At the back of the printer, install three screws (callout 1).
6. M452dw model only: Position the guide in the printer.
Figure 1-697 Install the guide

7. M452dw model only: Position the ground wire and Install one screw (callout 1). Install one screw
(callout 2).
Figure 1-698 Install two screws
2 1
8. M452dw model only: On the left side of the printer, on the formatter, connect one connector (callout 1).
Figure 1-699 Connect one connector

9. M452nw/dn models only: On the left side of the printer, on the formatter, connect one connector
(callout 1).
10. M452nw/dw models only: Connect the antenna (callout 1) to the connector (callout 2) on the wireless
PCA.
Figure 1-701 Connect the antenna
1
2
Step 12: Install the rear top cover (simplex model)


2
1
3 4

2

top of the cover.
2
1

1 2 3 4

1
2

2
1


1
2




then close it.


Removal and replacement: Top cover (M377, M477 models)
● Introduction
● Step 6: Remove the image scanner (M377, M477 models)
● Step 7: Remove the fax PCA (M477 models)
● Step 8: Remove the top cover (M377, M477 models)
● Step 9: Remove the control panel (M377, M477 models)
● Step 10: Remove the walk-up USB port (M377, M477 models)
● Step 12: Install the walk-up USB port (M377, M477 models)
● Step 13: Install the control panel (M377, M477 models)
● Step 14: Install the top cover (M377, M477 models)
● Step 15: Install the fax PCA (M477 models)
● Step 16: Install the image scanner
Introduction
This document provides the procedures to remove and replace the top cover for the M377, M477.
Before you begin


RM2-6466-000CN Top cover (M477fnw/fdn)
RM2-6468-000CN Top cover (M377, M477fdw)
Required tools






cover (callout 1).

cover.
1
2





engaging.
cover (callout 1).

4 3
2 1
3
1


2 1

Step 6: Remove the image scanner (M377, M477 models)
1. On the left side of the printer, disconnect three connectors (callout 1).
Figure 1-753 Disconnect the scanner cables

2. Raise the scanner cables up, and then remove one screw (callout 1) to release the ground wire
(callout 2).
Figure 1-754 Remove one screw and release the ground wire
1
2

4. With the scanner lifted, release the tab (callout 1) on the scanner support arm pin from the slot and
rotate the pin in the direction indicated.
Figure 1-756 Release the scanner arm pin
5. Remove the scanner arm pin.
CAUTION: Once the scanner arm pin is removed, support the scanner with one hand at all times so that
it does not fall backwards off of the printer.
Figure 1-757 Remove the scanner arm pin.

6. On the top of the printer, use a flat-blade screwdriver to release one tab (callout 1).
7. Remove the scanner cable cover.
Figure 1-759 Remove the scanner cable cover

8. The scanner cables (callout 1) are held in place on the top cover with double-sided tape. Carefully
release the cables from the top cover.
Figure 1-760 Release the cables
9. Open the scanner assembly fully, slide the assembly toward the right side of the printer, and then lift
the assembly off of the printer.
Figure 1-761 Remove the scanner assembly
2
1
Step 7: Remove the fax PCA (M477 models)
1. Disconnect one connector (callout 1). Beginning with the top right screw (callout 2) remove four screws
(callout 3) in a counterclockwise direction.

Figure 1-762 Disconnect one connector and remove four screws
2
3
2. Release one tab (callout 1), and then slide the fax cover (callout 2) toward the front of the printer to
remove it.
Figure 1-763 Remove the fax cover

3. Lift up to remove the fax PCA (callout 1).
Figure 1-764 Remove the fax PCA
Step 8: Remove the top cover (M377, M477 models)
1. On the left side of the printer, on the formatter PCA, disconnect two connectors (callout 1).
Figure 1-765 Disconnect two connectors

2. On the top cover, remove one screw (callout 1) and the sheet metal plate (callout 2).
Figure 1-766 Remove one screw and the sheet metal plate
3. At the top of the printer, lower the scanner support arm (callout 1), and then remove one screw
(callout 2).
Figure 1-767 Lower the support arm and remove one screw
2 1

4. Remove the scanner support arm (callout 1).
Figure 1-768 Remove the scanner support arm
5. At the top of the printer, remove three screws (callout 1).
Reinstallation tip: One screw (callout 2) is longer than the other screws. Make sure that this screw is
reinstalled in the correct position.

6. Behind the control panel, remove one screw (callout 1), and then use a small flat-blade screwdriver at
two pry points (callout 2) to release the control panel cover from the top cover.
Figure 1-770 Release the control panel cover
7. Remove the control panel cover (callout 1).
Figure 1-771 Remove the control panel cover

8. Remove the flat cable (callout 1) from the retaining guide (callout 2).
Figure 1-772 Release the flat cable
2
1
9. Remove two screws (callout 1), and then remove one screw (callout 2) and release one ground wire.
Reinstallation tip: The two screws toward the front of the control panel (callout 1) are longer than the
other screw. Make sure these screws are installed in the correct position when reinstalling the part.

10. Carefully lift the control panel away and rest it on the top cover, and then remove one screw (callout 1).
CAUTION: The control panel is still attached to the top cover by the flat cable.
11. Place the control panel back into position. With your hand, refasten the screw (callout 1) that was
previously removed from the control panel cover to temporarily reattach the control panel to the top
cover. Doing this should protect the flat cable from being damaged.
Figure 1-775 Refasten the control panel to the top cover

12. Remove the USB cable (callout 1) from the cable guides (callout 2).
Figure 1-776 Release the USB cable
13. At the front of the printer, remove two screws (callout 1).

14. Release one retainer (callout 1), and then release three tabs (callout 2).
Figure 1-778 Release one retainer and three tabs
Step 9: Remove the control panel (M377, M477 models)
1. Turn the top cover on its side, and then remove the flat cable (callout 1) from the cable guides
(callout 2).

Figure 1-780 Remove the flat cable from the guides
2. On the top of the top cover, use your finger to remove the screw (callout 1) that is temporarily holding
the control panel to the top cover.

3. Lift the control panel up and completely remove the flat cable (callout 1) from the slot (callout 2) in the
top cover.
1
2
Step 10: Remove the walk-up USB port (M377, M477 models)
1. Lay the top cover face-down. Behind the control panel, remove two screws (callout 1).

2. Slide the walk-up USB port (callout 1) out of the sheet metal opening (callout 2).
Figure 1-784 Slide the walk-up USB port
3. Release the cable (callout 1) from the guides (callout 2), and then disconnect one connector (callout 3).
Figure 1-785 Remove the walk-up USB port
3 1

Step 12: Install the walk-up USB port (M377, M477 models)
1. Connect one connector (callout 2), and then install the cable (callout 2) in the guides (callout 3).
Figure 1-787 Connect the walk-up USB port
1 2

2. Install the USB port (callout 1) into the sheet metal opening (callout 2), and then install the slots
(callout 3) on the walk-up USB port over the tabs (callout 4) on the top cover.
Figure 1-788 Install the walk-up USB port
1
4
3. Install two screws (callout 1).
Step 13: Install the control panel (M377, M477 models)
1. Install the flat cable (callout 1) in the slot (callout 2) in the top cover.

Figure 1-790 Install the flat cable
2. On the top of the cover, use your finger to install one screw (callout 1).

3. Turn the top cover on its side, and then route the flat cable (callout 1) through the cable guides
(callout 2).
Figure 1-792 Route the flat cable
Step 14: Install the top cover (M377, M477 models)
1. Position the top cover on the printer.

2. At the front of the printer, install one retainer (callout 1), and then install three tabs (callout 2).
Figure 1-794 Install one retainer and three tabs

4. Install the USB cable (callout 1) into the cable guides (callout 2).
Figure 1-796 Install the USB cable
5. With your hand, remove the screw (callout 1) that was previously installed to temporarily reattach the
control panel to the top cover.

6. Carefully lift the control panel away and rest it on the top cover, and then install one screw (callout 1).
7. Install two screws (callout 1), and then position the ground wire and install one screw (callout 2).

8. Install the flat cable (callout 1) under the retaining guide (callout 2).
2
1
9. Install the control panel cover (callout 1) behind the control panel.
Figure 1-801 Install the control panel cover

10. Make sure that two tabs (callout 1) are snapped into position, and then install one screw (callout 2).
11. At the top of the printer, install three screws (callout 1).
TIP: One screw (callout 2) is longer than the other screws. Make sure that this screw is installed in the
correct position.

12. Install the scanner support arm (callout 1).
Figure 1-804 Install the scanner support arm
13. Before installing the scanner support arm screw in the next step, use a small flat-blade screwdriver to
hold the metal plate (callout 1) up. Continue to hold the plate up while installing the screw so that the
screw attaches to the plate.
Figure 1-805 Raise the metal plate

14. Lower the scanner support arm (callout 1), and then install one screw (callout 2).
Figure 1-806 Lower the support arm and install one screw
2 1
15. Reinstall the metal plate (callout 1). Position the tab (callout 2) under the edge of the top cover
(callout 3).
Figure 1-807 Install the metal plate

16. Install one screw (callout 1) to secure the sheet metal plate (callout 2).
17. On the left side of the printer, on the formatter PCA, Connect two connectors (callout 1).
Figure 1-809 Connect two connectors
Step 15: Install the fax PCA (M477 models)
1. Position the fax PCA (callout 1) on the printer.

Figure 1-810 Install the fax PCA
2. Install the tabs (callout 1) on the fax cover in the slots (callout 2) on the top cover. Slide the cover toward
the back of the printer to install it.
Figure 1-811 Install the fax cover
1
2

3. Beginning with the lower right screw (callout 1) install four screws (callout 2) in a clockwise direction.
Connect one connector (callout 3).
Figure 1-812 Install four screws and connect one connector
Step 16: Install the image scanner
1. Lower the scanner assembly onto the printer, and then slide the assembly toward the left side of the
printer to install it.
Figure 1-813 Install the scanner assembly
1
2

2. Press the scanner cables (callout 1) down onto the double-sided tape on the top cover.
Figure 1-814 Press the cables
3. Install the tabs (callout 1) on the front of the scanner cable cover in the slots (callout 2) on the top cover.
Figure 1-815 Position the scanner cable cover

4. Press down on the back of the scanner cable cover to engage one tab (callout 1).
Figure 1-816 Install the scanner cable cover
5. With the scanner lid lifted, insert the scanner support arm pin (callout 1) into the slot in the scanner
support arm (callout 2).
Figure 1-817 Install the scanner arm pin

6. Rotate the tab on the scanner arm pin (callout 1) in the direction indicated to snap it into place.
Figure 1-818 Secure the scanner arm pin

8. Raise the scanner cables up, position the ground wire (callout 1), and then install one screw (callout 2).
Figure 1-820 Install the ground wire
2
1
9. Connect three connectors (callout 1).
Figure 1-821 Install the M377, M477 scanner


2
1
3 4




1 2
3 4
cover.
1
2

1
2

2
1


1
2






then close it.

Removal and replacement: Touchscreen control panel (M452dw model)
● Introduction
● Step 7: Remove the control panel (M452dw model)
● Step 9: Install the control panel (M452dw model)
Introduction
This document provides the procedures to remove and replace the touchscreen control panel for the M452dw.
Before you begin

Control panel part number
CF388-60113 Control panel (M452dw model)
Required tools





cover (callout 1).

1
2

1
2


reengaging.
cover (callout 1).

4 3 2 1

(callout 1).

(callout 1).

wireless PCA.
1
2
2 3 1


(callout 2).
(callout 2).

Step 7: Remove the control panel (M452dw model)
1. On the underside of the top cover, remove three screws (callout 1), and then carefully unfasten the tape
strips (callout 2) to unroute the control-panel flat cable.
TIP: HP recommends keeping the tape strips for reuse when the control panel is reinstalled.

Figure 1-881 Remove three screws and unroute cable
2. Lift up on the bracket (callout 1) to remove it.

3. Rotate the control panel away from the top cover.
Figure 1-883 Rotate the control panel
4. Pull the control panel away from the top side of the top cover to remove it.

Step 9: Install the control panel (M452dw model)
1. On the top side of the top cover, set the control panel in place.
Figure 1-886 Set the control panel in place

2. On the underside of the top cover, install the bracket (callout 1).
3. On the underside of the top cover, install three screws (callout 1), and then carefully fasten the tape
strips (callout 2) to affix the control-panel flat cable to the cover.
CAUTION: Ensure that the control-panel cable is securely fastened to the control panel and the top
cover. Pinching the cable between the cover and the chassis can damage the cable.
Figure 1-888 Install three screws and fasten the cable


(callout 2).
(callout 2).


(callout 2).
2 1

(callout 1).
PCA.
1
2


2
1
3 4

2

top of the cover.
2
1

1 2 3 4

1
2

2
1


1
2




then close it.


Removal and replacement: Touchscreen control panel (M377, M477 models)
● Introduction
● Step 6: Remove the image scanner (M377, M477 models)
● Step 9: Remove the control panel (M377, M477 models)
● Step 11: Install the control panel (M377, M477 models)
● Step 14: Install the image scanner (M377, M477 models)
Introduction
This document provides the procedures to remove and replace the control panel for the M377, M477.
Before you begin


Control panel part number
B5L25-60101 Control panel (M377, M477 models)
Required tools






cover (callout 1).

cover.
1
2





engaging.
cover (callout 1).

4 3
2 1
3
1


2 1

Step 6: Remove the image scanner (M377, M477 models)

(callout 2).
1
2



2
1

2
3
remove it.


(callout 2).
2 1



2
1



Step 9: Remove the control panel (M377, M477 models)
1. Turn the top cover on its side, and then remove the flat cable (callout 1) from the cable guides
(callout 2).

Figure 1-977 Remove the flat cable from the guides
2. On the top of the top cover, use your finger to remove the screw (callout 1) that is temporarily holding
the control panel to the top cover.

3. Lift the control panel up and completely remove the flat cable (callout 1) from the slot (callout 2) in the
top cover.
1
2
Step 11: Install the control panel (M377, M477 models)
1. Install the flat cable (callout 1) in the slot (callout 2) in the top cover.

2. On the top of the cover, use your finger to install one screw (callout 1).

3. Turn the top cover on its side, and then route the flat cable (callout 1) through the cable guides
(callout 2).
Figure 1-983 Route the flat cable




2
1

correct position.


2 1
(callout 3).


1
2

Step 14: Install the image scanner (M377, M477 models)
1
2




2
1


2
1
3 4




1 2
3 4
cover.
1
2

1
2

2
1


1
2






then close it.

Removal and replacement: Integrated scanner assembly (M377, M477 models)
● Introduction
● Step 4: Remove the integrated scanner assembly
● Step 6: Install the integrated scanner assembly
Introduction
This document provides the procedures to remove and replace the integrated scanner assembly for the M377,
M477.
Before you begin

Integrated scanner assembly part number
CF377-60104 Integrated scanner assembly
Required tools






engaging.

cover (callout 1).
4 3
2 1

3
1

2 1
Step 4: Remove the integrated scanner assembly

(callout 2).
1
2




2
1
Step 6: Install the integrated scanner assembly

1
2



2
1

2
1
3 4




1 2
3 4
cover.
1
2

1
2



then close it.


Removal and replacement: Internal parts and assemblies
● Removal and replacement: Power switch assembly
● Removal and replacement: Toner cartridge tray
● Removal and replacement: Cartridge fan
● Removal and replacement: Power supply fan
● Removal and replacement: Low-voltage power supply (LVPS)
● Removal and replacement: Pickup motor
● Removal and replacement: Driver PCA
● Removal and replacement: Drum motor
● Removal and replacement: Developer motor
● Removal and replacement: Secondary transfer assembly (simplex models)
● Removal and replacement: Secondary transfer assembly (duplex models)
● Removal and replacement: Intermediate transfer belt (ITB)
● Removal and replacement: Registration density sensor
● Removal and replacement: Re-pickup assembly (duplex models)
● Removal and replacement: Engine controller PCA
● Removal and replacement: Lifter drive assembly
● Removal and replacement: Pickup assembly
● Removal and replacement: Front feed guide assembly
● Removal and replacement: Rear feed guide assembly
● Removal and replacement: Registration assembly
● Removal and replacement: Memory PCA
● Removal and replacement: Laser scanner (M452 models)
● Removal and replacement: Laser scanner ( M377, M477 models)
● Removal and replacement: Fuser (simplex models)
● Removal and replacement: Fuser (duplex models)
● Removal and replacement: Fuser power supply
● Removal and replacement: Fuser motor
● Removal and replacement: Duplex drive assembly (duplex models)
● Removal and replacement: Wireless antenna (M452nw/dw models)
● Removal and replacement: Wireless PCA (M452nw/dw models)

● Removal and replacement: Wireless PCA (M377, M477fnw/fdw models)
● Removal and replacement: Formatter PCA
● Removal and replacement: Environmental sensor
● Removal and replacement: Fax PCA (M477 models)
● Removal and replacement: NFC PCA (M452dw and M477dw models)
● Removal and replacement: Walk-up USB port (M452dw model)
● Removal and replacement: Walk-up USB port (M377, M477 models)
● Removal and replacement: Drawer connector

Removal and replacement: Power switch assembly
● Introduction
● Step 5: Remove the power switch assembly
● Step 7: Install the power switch assembly
Introduction
This document provides the procedures to remove and replace the power switch assembly.
Before you begin

Power switch assembly part number
RM2-6373-000CN Power switch assembly
Required tools






cover (callout 1).

1
2

1
2

Remove the power switch assembly on page 610.


cover (callout 1).
cover.
1
2




Step 5: Remove the power switch assembly
1. On the front of the printer, remove one screw (callout 1), and then release three tabs (callout 2).
Figure 1-1116 Remove one screw and release three tabs

2. Disconnect one connector (callout 1).
Step 7: Install the power switch assembly
1. Install the tabs (callout 1) on the power switch into the corresponding slots (callout 2) on the printer.

Figure 1-1119 Install the power switch
2. Make sure that the spring (callout 1) is positioned around the screw hole.
Figure 1-1120 Check the spring position

3. Install one screw (callout 1), and then connect one connector (callout 2).
Figure 1-1121 Install one screw and connect one connector
2
1


1
2



2
1


1
2





then close it.


Removal and replacement: Toner cartridge tray
● Introduction
● Step 3: Open the rear door or duplexer door
● Step 6: Remove the toner cartridge tray
● Step 8: Install the toner cartridge tray
● Step 11: Close the rear door or duplexer door
Introduction
This document provides the procedures to remove and replace the toner cartridge tray.
Before you begin

Toner cartridge tray part number
RM2-6401-000CN Toner cartridge tray
Required tools


M477 models.


Step 3: Open the rear door or duplexer door


reengaging.

cover (callout 1).
4 3 2 1

Remove the toner cartridge tray on page 637.

engaging.

cover (callout 1).
4 3
2 1

3
1

2 1
Step 6: Remove the toner cartridge tray
1. Release the tab (callout 1) on the front door hinge arm from the slot (callout 2) on the tray slide
mechanism.

Figure 1-1168 Release the hinge arm
1 2
2. Remove two screws (callout 1).

3. Remove the cover (callout 1).
4. Pull the tray slide mechanism (callout 1) out.
Figure 1-1171 Pull the tray slide mechanism out

5. Slide the cartridge tray out of the printer (callout 1). Rotate the tray counterclockwise (callout 2) to
release one silver shaft (callout 3).
Figure 1-1172 Rotate the cartridge tray to release one shaft
6. Continue to rotate the tray to release the edge of the tray (callout 1) from the white clip (callout 2).
Figure 1-1173 Remove the cartridge tray
2
1

Step 8: Install the toner cartridge tray
1. Install the edge of the tray (callout 1) into the white clip (callout 2), and then rotate the tray clockwise.
Figure 1-1175 Install the white clip
2
1

2. Install the silver shaft (callout 1) over the edge of the sheet metal (callout 2) on the cartridge tray.
Figure 1-1176 Install the silver shaft
3. Rotate the tray clockwise (callout 1), and then slide the tray into the printer (callout 2).
Figure 1-1177 Rotate the tray

4. Slide the tray slide mechanism (callout 1) into the printer.
Figure 1-1178 Slide the tray slide mechanism in
5. Install the tab on the cover (callout 1) into the slot (callout 2) on the printer. Then, install the slot
(callout 3) on the cover over the tray slide mechanism (callout 4) on the printer.
Figure 1-1179 Install the cover
4
1
3 2

7. Install the tab (callout 1) on the front door hinge arm into the slot (callout 2) on the tray slide
mechanism.
Figure 1-1181 Install the hinge arm
1 2

2
1
3 4

2

top of the cover.
2
1

1 2 3 4

1
2
the rear door or duplexer door on page 655.

2
1
3 4




1 2
3 4
cover.
1
2

1
2

Step 11: Close the rear door or duplexer door





then close it.

Removal and replacement: Cartridge fan
● Introduction
● Step 5: Remove the cartridge fan
● Step 7: Install the cartridge fan
Introduction
This document provides the procedures to remove and replace the cartridge fan.
Before you begin

Cartridge fan part number
RK2-6270-000CN Cartridge fan
Required tools






cover (callout 1).

1
2

1
2

Remove the cartridge fan on page 673.


cover (callout 1).
cover.
1
2




Step 5: Remove the cartridge fan
1. Disconnect one connector (callout 1), and then remove the cables (callout 2) from the wire guides
(callout 3).
Figure 1-1236 Disconnect one connector and release cables from guides
3 2 1

2. Release three tabs (callout 1).
3. Remove the cartridge fan (callout 1).
Figure 1-1238 Remove the cartridge fan

Step 7: Install the cartridge fan
1. Position the cartridge fan so that the white label (callout 1) is facing the printer and the top embossed
arrow (callout 2) is pointing into the printer.
Figure 1-1240 Install the cartridge fan

2. Make sure that the fan is snaps into position under three tabs (callout 1).
Figure 1-1241 Install three tabs
3. Connect one connector (callout 1), and then install the cables (callout 2) into the wire guides (callout 3).
Figure 1-1242 Connect one connector and install cables into guides
3 2 1

2
1


1
2


2
1


1
2






then close it.

Removal and replacement: Power supply fan
● Introduction
● Step 5: Remove the power supply fan
● Step 7: Install the power supply fan
Introduction
This document provides the procedures to remove and replace the power supply fan.
Before you begin

Power supply fan part number
RK2-6270-000CN Power supply fan
Required tools





cover (callout 1).

1
2

1
2

Remove the power supply fan on page 702.


cover (callout 1).
cover.
1
2




Step 5: Remove the power supply fan
1. Disconnect one connector (callout 1), and then remove the cable (callout 2) from the wire guide
(callout 3).
3 1

2. Release the spring (callout 1) from the tab (callout 2).
Figure 1-1293 Release the spring

4. Remove the power supply fan (callout 1).
Figure 1-1295 Remove the power supply fan
Step 7: Install the power supply fan
1. Position the power supply fan so that the white label (callout 1) is facing the printer.

Figure 1-1297 Install the power supply fan
2. Make sure that the fan is snaps into position under two tabs (callout 1).

3. Install the spring (callout 1) behind the tab (callout 2).
Figure 1-1299 Install the spring
4. Connect one connector (callout 1), and then install the cable (callout 2) into the wire guide (callout 3).
Figure 1-1300 Connect one connector and install cables into guides
3 1

2
1


1
2


2
1


1
2






then close it.

Removal and replacement: Low-voltage power supply (LVPS)
● Introduction
● Step 7: Remove the duplexer door assembly (duplex models)
● Step 9: Remove the LVPS
● Step 11: Install the LVPS
● Step 13: Install the duplexer door assembly (duplex models)
Introduction
This document provides the procedures to remove and replace the low-voltage power supply.
Before you begin


Low-voltage power supply part number
RM2-7913-000CN Low-voltage power supply (110V)
RM2-7914-000CN Low-voltage power supply (220V)
Required tools






cover (callout 1).
1
2

2
1
2



cover (callout 1).

cover.
1
2




reengaging.

cover (callout 1).
4 3 2 1

Remove the duplexer door assembly (duplex models) on page 739.

engaging.

cover (callout 1).
4 3
2 1

3
1

2 1
Step 7: Remove the duplexer door assembly (duplex models)
NOTE: This step is for duplex models. For simplex models, skip this step and go to Step 8: Remove the rear
door (simplex models) on page 741.


NOTE: This step is for simplex models. For duplex models, skip this step and go to Step 9: Remove the LVPS
on page 742.

Step 9: Remove the LVPS
(callout 3).
1
2

3. Release the hinge arm (callout 1).

4. Release one tab (callout 1) on the right side of the power supply fan.
5. Lift the front door up slightly (callout 1), and then remove the power supply fan and holder (callout 2).
Figure 1-1373 Remove the power supply fan and holder

6. Before disconnecting the cables in the next step, make note of the position of two cables (callout 1).
IMPORTANT: These cables can be inadvertently switched when reinstalling. The connectors on the
cables will fit in either connector on the LVPS. Make sure that these cables are installed in the correct
connectors. If the cables are switched, the printer will not power on when reassembled.
Figure 1-1374 Check the connectors
7. Disconnect five connectors (callout 1). Note that one connector (callout 2) has a latch that must be
released before disconnecting it. Remove four screws (callout 3).
Figure 1-1375 Disconnect five connectors and remove four screws
1
2

8. Remove two screws (callout 1), and then release three tabs (callout 2).
Figure 1-1376 Remove two screws and release three tabs
1 2
9. Remove the LVPS (callout 1).
Figure 1-1377 Remove the LVPS

Step 11: Install the LVPS
1. Install the tab (callout 1) on the LVPS into the slot (callout 2) in the printer. Install the slots (callout 3) in
the LVPS over the tabs (callout 4) on the printer.
Figure 1-1379 Install the side tabs of the LVPS
1 2
3 4

2. At the back of the printer, install the tabs on the LVPS (callout 1) into the slots (callout 2) in the printer.
Figure 1-1380 Install the back tabs of the LVPS
2
1

4. Connect five connectors (callout 1), and then install four screws (callout 2).
Figure 1-1382 Connect five connectors and install four screws
IMPORTANT: Two of the cables (callout 1) can be inadvertently switched. The connectors on the cables
will fit in either connector on the LVPS. Make sure these cables are installed in the correct connectors. If
these cables are switched, the printer will not power on when reassembled.

5. Lift the front door up slightly (callout 1), and then install the power supply fan and holder (callout 2).
6. Install the hinge arm (callout 1).

Figure 1-1387 Connect one connector and install cables in the guides
1
2
NOTE: This step is for simplex models. For duplex models, skip this step and go to Step 13: Install the
duplexer door assembly (duplex models) on page 752.

Step 13: Install the duplexer door assembly (duplex models)
NOTE: This step is for duplex models. For simplex models, skip this step and go to Step 14: Install the left
cover (M452 models) on page 754.
2
1

2
1

the retention arm.
2
1
3 4


2

top of the cover.
2
1

1 2 3 4

1
2

2
1
3 4




1 2
3 4
cover.
1
2

1
2

2
1


1
2



2
1


1
2





then close it.


Removal and replacement: Pickup motor
● Introduction
● Step 9: Remove the low-voltage power supply (LVPS)
● Step 10: Remove the pickup motor
● Step 12: Install the pickup motor
● Step 13: Install the LVPS
Introduction
This document provides the procedures to remove and replace the pickup motor.
Before you begin


Pickup motor part number
RM2-7350-000CN Pickup motor
Required tools






cover (callout 1).
1
2

2
1
2



cover (callout 1).

cover.
1
2




reengaging.

cover (callout 1).
4 3 2 1


engaging.

cover (callout 1).
4 3
2 1

3
1

2 1


NOTE: This step is for simplex models. For duplex models, skip this step and go to Step 9: Remove the low-
voltage power supply (LVPS) on page 801.

Step 9: Remove the low-voltage power supply (LVPS)
(callout 3).
1
2



1
2

1 2
Step 10: Remove the pickup motor
1. Release one tab (callout 1), and then slide the fan duct (callout 2) up to remove it.

Figure 1-1490 Remove the fan duct
1
2
2. Disconnect one connector (callout 1), remove two screws (callout 2), and then remove the pickup motor
(callout 3).
Figure 1-1491 Remove the pickup motor

Step 12: Install the pickup motor
1. Position the pickup motor (callout 1) on the printer. Install two screws (callout 2), and then connect one
connector (callout 3).
Figure 1-1493 Install the pickup motor

2. Position the fan duct (callout 1) on the printer. Slide the fan duct down to engage one tab (callout 2).
Figure 1-1494 Install the fan duct
2
1
Step 13: Install the LVPS
1 2
3 4

2
1



1
2
duplexer door assembly on page 813.

2
1

2
1

the retention arm.
2
1
3 4


2

top of the cover.
2
1

1 2 3 4

1
2

2
1
3 4




1 2
3 4
cover.
1
2

1
2

2
1


1
2



2
1


1
2





then close it.


Removal and replacement: Driver PCA
● Introduction
● Step 5: Remove the driver PCA
● Step 7: Install the driver PCA
Introduction
This document provides the procedures to remove and replace the driver PCA.
Before you begin

Driver PCA part number
RM2-7369-000CN Driver PCA
Required tools






cover (callout 1).

1
2

1
2

Remove the driver PCA on page 852.


cover (callout 1).
cover.
1
2




Step 5: Remove the driver PCA

2. Release one retainer (callout 1), disconnect all of the connectors on the driver PCA, remove one screw
(callout 2), and then release two tabs (callout 3).
Figure 1-1579 Disconnect all connectors and remove one screw
3 2
3. Rotate the top of the driver PCA away from the printer (callout 1), and then lift up (callout 2) to remove
it.
Figure 1-1580 Remove the driver PCA

Step 7: Install the driver PCA
1. Make sure that all of the cables (callout 1) are positioned in front of the driver PCA. Position the bottom
of the driver PCA (callout 2) against the PCA holder, and then rotate the top of the PCA (callout 3) toward
the printer until it snaps into place.
Figure 1-1582 Install the driver PCA
1
2

2. When connecting the connectors in the next step, make sure that the power supply fan connector
(callout 1) and the cartridge fan connector (callout 2) are installed in the correct positions.
Figure 1-1583 Fan connector locations
2
1
3. Install one screw (callout 1), connect all of the connectors on the driver PCA, and then close one retainer
(callout 2).
Figure 1-1584 Install one screw and connect all connectors

4. Connect one connector (callout 1).
2
1


1
2



2
1


1
2





then close it.


Removal and replacement: Drum motor
● Introduction
● Step 11: Remove the driver PCA holder
● Step 12: Remove the drum motor
● Step 14: Install the drum motor
● Step 15: Install the driver PCA holder
● Step 17: Install the low-voltage power supply (LVPS)
Introduction
This document provides the procedures to remove and replace the drum motor.

Before you begin
Drum motor part number
RM2-7342-000CNN Drum motor
Required tools






cover (callout 1).
1
2

2
1
2



cover (callout 1).

cover.
1
2




reengaging.

cover (callout 1).
4 3 2 1


engaging.

cover (callout 1).
4 3
2 1

3
1

2 1



(callout 3).
1
2



1
2

1 2

3 2

it.
Step 11: Remove the driver PCA holder
1. Disconnect one connector (callout 1), and then release the cables (callout 2) from the guides (callout 3).
1
2

3. Release the cables from the driver PCA holder (callout 1), and then remove the driver PCA holder.
Figure 1-1668 Remove the driver PCA holder
Step 12: Remove the drum motor

▲ Disconnect one connector (callout 1), remove four screws (callout 2), and then remove the drum motor
(callout 3).

Figure 1-1669 Remove the drum motor
3 1
Step 14: Install the drum motor

▲ Position the drum motor on the printer (callout 1), install four screws (callout 2), and then connect one

Figure 1-1671 Install the drum motor
1 3
Step 15: Install the driver PCA holder
1. Install the cables through the opening in the driver PCA holder (callout 1).
Figure 1-1672 Install the cables in the driver PCA holder

2. Position the driver PCA holder behind one metal tab (callout 1), and then install three tabs (callout 2).
Figure 1-1673 Install the driver PCA holder
3. Connect one connector (callout 1), and then install the cables (callout 2) into the guides (callout 3).
Figure 1-1674 Connect one connector and install cables into the guides
1
2

1
2
2
1

(callout 2).
Step 17: Install the low-voltage power supply (LVPS)

1 2
3 4
2
1




1
2

2
1

2
1

the retention arm.
2
1
3 4


2

top of the cover.
2
1

1 2 3 4

1
2

2
1
3 4




1 2
3 4
cover.
1
2

1
2

2
1


1
2



2
1


1
2





then close it.


Removal and replacement: Developer motor
● Introduction
● Step 7: Remove the duplexer door assembly
● Step 11: Remove the driver PCA holder
● Step 12: Remove the developer motor
● Step 14: Install the developer motor
● Step 15: Install the driver PCA holder
● Step 17: Install the low-voltage power supply (LVPS)
Introduction
This document provides the procedures to remove and replace the developer motor.

Before you begin
Developer motor part number
RM2-7344-000CN Developer motor
Required tools






cover (callout 1).
1
2

2
1
2



cover (callout 1).

cover.
1
2




reengaging.

cover (callout 1).
4 3 2 1

Remove the duplexer door assembly on page 956.

engaging.

cover (callout 1).
4 3
2 1

3
1

2 1
Step 7: Remove the duplexer door assembly



(callout 3).
1
2



1
2

1 2

3 2

it.
Step 11: Remove the driver PCA holder
1. Disconnect one connector (callout 1), and then release the cables (callout 2) from the guides (callout 3).
1
2

3. Release the cables from the driver PCA holder (callout 1), and then remove the driver PCA holder.
Figure 1-1795 Remove the driver PCA holder
Step 12: Remove the developer motor

▲ Remove four screws (callout 1), lift the developer motor away from the printer slightly (callout 2), and
then disconnect one connector (callout 3).

Figure 1-1796 Remove the developer motor
3 1
Step 14: Install the developer motor

▲ Connect one connector (callout 1), position the developer motor on the printer (callout 2), and then
install four screws (callout 3).

Figure 1-1798 Install the developer motor
1 3
Step 15: Install the driver PCA holder
1. Install the cables through the opening in the driver PCA holder (callout 1).
Figure 1-1799 Install the cables in the driver PCA holder

2. Position the driver PCA holder behind one metal tab (callout 1), and then install three tabs (callout 2).
Figure 1-1800 Install the driver PCA holder
Figure 1-1801 Connect one connector and install cables into the guides
1
2

1
2
2
1

(callout 2).
Step 17: Install the low-voltage power supply (LVPS)

1 2
3 4
2
1




1
2
duplexer door assembly on page 977.

2
1

2
1

the retention arm.
2
1
3 4


2

top of the cover.
2
1

1 2 3 4

1
2

2
1
3 4




1 2
3 4
cover.
1
2

1
2

2
1


1
2



2
1


1
2





then close it.


Removal and replacement: Secondary transfer assembly (simplex models)
● Introduction
● Step 1: Remove the secondary transfer assembly
● Step 3: Install the secondary transfer assembly
Introduction
This document provides the procedures to remove and replace the secondary transfer assembly for simplex
models.
Before you begin

Secondary transfer assembly part number
RM2-6430-000CN Secondary transfer assembly (simplex models)
Required tools

Step 1: Remove the secondary transfer assembly

2. Remove one retainer collar (callout 1).
Figure 1-1865 Remove one retainer collar

3. Lift the assembly up slightly (callout 1), and then slide it to the left (callout 2).
Figure 1-1866 Slide the assembly left
1
2
4. Rotate the right side of the assembly away from the printer to remove it.
Figure 1-1867 Remove the secondary transfer assembly

Step 3: Install the secondary transfer assembly
1. Install the shaft on the secondary transfer assembly into the hole in the printer (callout 1), and then
rotate the right side of the assembly toward the printer to install it (callout 2).
CAUTION: Do not touch or damage the secondary transfer roller (callout 3).
Figure 1-1869 Position the secondary transfer assembly

2. Lift the assembly up slightly (callout 1), and then slide it to the right (callout 2).
Figure 1-1870 Slide the assembly right
1
2
3. Install one retainer collar (callout 1).
Figure 1-1871 Install one retainer collar


Removal and replacement: Secondary transfer assembly (duplex models)
● Introduction
● Step 1: Remove the secondary transfer assembly
● Step 3: Install the secondary transfer assembly
Introduction
This document provides the procedures to remove and replace the secondary transfer assembly for duplex
models.
Before you begin

Secondary transfer assembly part number
RM2-6397-000CN Secondary transfer assembly (duplex models)
Required tools

Step 1: Remove the secondary transfer assembly


3. Remove one screw (callout 1), and then release the retaining arm (callout 2).
Figure 1-1875 Remove one screw and release the arm
1
2

5. Rotate the right side of the assembly away from the printer (callout 1) so that the left side of the
assembly rotates free of the plastic tab (callout 2). Remove the assembly.
Step 3: Install the secondary transfer assembly
1. Install the left edge of the secondary transfer assembly behind the plastic tab (callout 1), and then

1
3
1
2

3. Position the retaining arm (callout 1) on the printer, and then install one screw (callout 2).


Removal and replacement: Intermediate transfer belt (ITB)
● Introduction
● Step 7: Remove the secondary transfer assembly (simplex models)
● Step 8: Remove the secondary transfer assembly (duplex models)
● Step 9: Remove the ITB
● Step 11: Install the ITB
● Step 12: Install the secondary transfer assembly (simplex models)
● Step 13: Install the secondary transfer assembly (duplex models)
Introduction
This document provides the procedures to remove and replace the intermediate transfer belt.
Before you begin


Intermediate transfer belt part number
RM2-6454-000CN Intermediate transfer belt
Required tools






cover (callout 1).
1
2

2
1
2



cover (callout 1).

cover.
1
2




reengaging.

cover (callout 1).
4 3 2 1

Remove the secondary transfer assembly (simplex models) on page 1036.

engaging.

cover (callout 1).
4 3
2 1

3
1

2 1
Step 7: Remove the secondary transfer assembly (simplex models)
NOTE: This step is for simplex models. For duplex models, skip this step and go to Step 8: Remove the
secondary transfer assembly (duplex models) on page 1038.


1
2
Step 8: Remove the secondary transfer assembly (duplex models)
NOTE: This step is for duplex models. For simplex models, skip this step and go to Step 9: Remove the ITB
on page 1041.


1
2

Step 9: Remove the ITB

2. Locate two levers (callout 1) above the low-voltage power supply, and then rotate them down to release
them.
Figure 1-1933 Release two levers
3. Use a small flat-blade screwdriver to pull the levers away from the printer until they stop.
Figure 1-1934 Pull two levers out

4. Release one tab (callout 1).
5. Remove the cover.
Figure 1-1936 Remove the cover.

6. Use a small flat-blade screwdriver to release the retainers and remove two connectors (callout 1).
7. Release one tab (callout 1) on the left side of the fuser cover, and then release one tab (callout 2) on the
right side.
1 2

8. Remove the fuser cover (callout 1).
Figure 1-1939 Remove the fuser cover

10. Press up on two tabs with thumbs (callout 1) and position fingers on the sheet metal on the top of the
ITB (callout 2).
CAUTION: Do not touch the silver surface of the ITB. Skin oils on the ITB will cause print-quality
problems.
11. Slide the ITB out of the printer.
CAUTION: Do not tamper with any of the white fittings on the side of the ITB.
Figure 1-1942 Slide the ITB out

Step 11: Install the ITB
1. Use a soft, lint-free cloth to remove any paper dust from the mylar strips (callout 1) under the ITB.
Figure 1-1944 Clean the mylar strips

2. Verify that the tabs on the end of the ITB are in the position shown.
Figure 1-1945 Check tabs on the end of the ITB
Figure 1-1946 Lower both tabs on each side of the ITB to the position shown

3. Slide the ITB into the printer.
problems.
Figure 1-1947 Slide the ITB in

5. Install the tabs on the fuser cover (callout 1) into the slots (callout 2) in the printer, and then snap the
cover into place.
Figure 1-1949 Install the fuser cover
6. Connect two connectors (callout 1).

7. Position the tabs (callout 1) on the cover into the slots (callout 2) on the printer, and then snap the cover
into place.
Figure 1-1951 Install the cover.
2
1

8. Use a small flat-blade screwdriver to push the levers into the printer until they stop.
Figure 1-1952 Push two levers in
Figure 1-1953 Push two levers in (different view)

9. Rotate the levers up until they snap into place.
Figure 1-1954 Rotate two levers into place
Step 12: Install the secondary transfer assembly (simplex models)

1
2

Step 13: Install the secondary transfer assembly (duplex models)

1
3
1
2


2
1
3 4


2

top of the cover.
2
1

1 2 3 4

1
2

2
1
3 4




1 2
3 4
cover.
1
2

1
2

2
1


1
2



2
1


1
2





then close it.


Removal and replacement: Registration density sensor
● Introduction
● Step 8: Remove the secondary transfer assembly (simplex models)
● Step 9: Remove the secondary transfer assembly (duplex models)
● Step 10: Remove the intermediate transfer belt (ITB)
● Step 11: Remove the toner cartridge tray
● Step 12: Remove the registration density sensor
● Step 14: Install the registration density sensor
● Step 15: Install the toner cartridge tray
● Step 16: Install the intermediate transfer belt (ITB)
● Step 17: Install the secondary transfer assembly (simplex models)
● Step 18: Install the secondary transfer assembly (duplex models)
Introduction
This document provides the procedures to remove and replace the registration density sensor.

Before you begin
Registration density sensor part number
RM2-7399-000CN Registration density sensor
Required tools


M477 models.





cover (callout 1).

1
2

1
2



cover (callout 1).
cover.
1
2





reengaging.
cover (callout 1).

4 3 2 1
Remove the secondary transfer assembly (simplex models) on page 1104.


engaging.
cover (callout 1).

4 3
2 1
3
1


2 1
Step 8: Remove the secondary transfer assembly (simplex models)

1
2

Step 9: Remove the secondary transfer assembly (duplex models)
NOTE: This step is for duplex models. For simplex models, skip this step and go to Step 10: Remove the
intermediate transfer belt (ITB) on page 1108.


1
2
Step 10: Remove the intermediate transfer belt (ITB)

2. Locate two levers (callout 1) above the low-voltage power supply, and then rotate them down to release
them.
Figure 1-2061 Release two levers

3. Use a small flat-blade screwdriver to pull the levers away from the printer until they stop.
Figure 1-2062 Pull two levers out

Figure 1-2064 Remove the cover.
6. Use a small flat-blade screwdriver to release the retainers and remove two connectors (callout 1).

7. Release one tab (callout 1) on the left side of the fuser cover, and then release one tab (callout 2) on the
right side.
1 2
8. Remove the fuser cover (callout 1).
Figure 1-2067 Remove the fuser cover

10. Press up on two tabs with thumbs (callout 1) and position fingers on the sheet metal on the top of the
ITB (callout 2).
problems.

11. Slide the ITB out of the printer.
CAUTION: Do not tamper with any of the white fittings on the side of the ITB.
Figure 1-2070 Slide the ITB out
Step 11: Remove the toner cartridge tray
1. Release the tab (callout 1) on the front door hinge arm from the slot (callout 2) on the tray slide
mechanism.
1 2

3. Remove the cover (callout 1).

4. Pull the tray slide mechanism (callout 1) out.
Figure 1-2074 Pull the tray slide mechanism out
5. Slide the cartridge tray out of the printer (callout 1). Rotate the tray counterclockwise (callout 2) to
release one silver shaft (callout 3).
Figure 1-2075 Rotate the cartridge tray to release one shaft

6. Continue to rotate the tray to release the edge of the tray (callout 1) from the white clip (callout 2).
Figure 1-2076 Remove the cartridge tray
2
1
Step 12: Remove the registration density sensor
1. The registration density sensor (callout 1) is located behind the Tray 1 pickup and feed rollers.
Figure 1-2077 Location of the registration density sensor

2. On the left side of the printer, disconnect one connector (callout 1), and then release the cables
(callout 2) from the guide (callout 3).
Figure 1-2078 Disconnect one connector and release cables
1
3

4. Slide the registration density sensor (callout 1) and the cable guide (callout 2) to the right to release
them.
Figure 1-2080 Slide the sensor and cable guide right
2 1
5. Release the connector through the opening in the sheet metal (callout 1).
Figure 1-2081 Release the connector

6. Remove the registration density sensor and cable guide.
Figure 1-2082 Remove the registration density sensor and guide
7. Release the cables (callout 1) from the guides (callout 2).
Figure 1-2083 Release the cables from the guides

8. Remove the cable guide (callout 1).
Figure 1-2084 Remove the cable guide
Step 14: Install the registration density sensor
1. If the spring on the registration density sensor becomes dislodged, reinstall it as shown below.

Figure 1-2086 Reinstall spring
2. Position the cable guide on the replacement registration density sensor, and then install the cables
(callout 1) into the guides (callout 2).
Figure 1-2087 Install the cables in the guides

3. Install the connector through the opening in the sheet metal (callout 1).
Figure 1-2088 Install the connector
4. Install the tabs (callout 1) on the cable guide into the slots (callout 2) in the printer.
Figure 1-2089 Install the cable guide tabs

5. Install the tabs (callout 1) on the registration density sensor into the slots (callout 2) in the printer.
6. Slide the registration density sensor (callout 1) and the cable guide (callout 2) to the left to install them.
Figure 1-2091 Install the registration density sensor
2 1

7. On the left side of the printer, connect one connector (callout 1), and then install the cables (callout 2) in
the guide (callout 3).
1
3
Step 15: Install the toner cartridge tray
1. Install the edge of the tray (callout 1) into the white clip (callout 2), and then rotate the tray clockwise.
Figure 1-2093 Install the white clip
2
1

2. Install the silver shaft (callout 1) over the edge of the sheet metal (callout 2) on the cartridge tray.
Figure 1-2094 Install the silver shaft
3. Rotate the tray clockwise (callout 1), and then slide the tray into the printer (callout 2).
Figure 1-2095 Rotate the tray

4. Slide the tray slide mechanism (callout 1) into the printer.
Figure 1-2096 Slide the tray slide mechanism in
5. Install the tab on the cover (callout 1) into the slot (callout 2) on the printer. Then, install the slot
(callout 3) on the cover over the tray slide mechanism (callout 4) on the printer.
4
1
3 2

7. Install the tab (callout 1) on the front door hinge arm into the slot (callout 2) on the tray slide
mechanism.
1 2
Step 16: Install the intermediate transfer belt (ITB)
1. Use a soft, lint-free cloth to remove any paper dust from the mylar strips (callout 1) under the ITB.

Figure 1-2100 Clean the mylar strips

2. Verify that the tabs on the end of the ITB are in the position shown.
Figure 1-2101 Check tabs on the end of the ITB
Figure 1-2102 Lower both tabs on each side of the ITB to the position shown

3. Slide the ITB into the printer.
problems.
Figure 1-2103 Slide the ITB in

5. Install the tabs on the fuser cover (callout 1) into the slots (callout 2) in the printer, and then snap the
cover into place.
Figure 1-2105 Install the fuser cover
6. Connect two connectors (callout 1).

7. Position the tabs (callout 1) on the cover into the slots (callout 2) on the printer, and then snap the cover
into place.
Figure 1-2107 Install the cover.
2
1

8. Use a small flat-blade screwdriver to push the levers into the printer until they stop.
Figure 1-2108 Push two levers in
Figure 1-2109 Push two levers in (different view)

9. Rotate the levers up until they snap into place.
Figure 1-2110 Rotate two levers into place
Step 17: Install the secondary transfer assembly (simplex models)

1
2

Step 18: Install the secondary transfer assembly (duplex models)

1
3
1
2


2
1
3 4


2

top of the cover.
2
1

1 2 3 4

1
2

2
1
3 4




1 2
3 4
cover.
1
2

1
2

2
1


1
2



2
1


1
2








then close it.

Removal and replacement: Re-pickup assembly (duplex models)
● Introduction
● Step 3: Open the duplexer door
● Step 8: Remove the duplexer door (duplex models)
● Step 9: Remove the re-pickup assembly
● Step 11: Install the re-pickup assembly
● Step 12: Install the duplexer door (duplex models)
● Step 17: Close the duplexer door
Introduction
This document provides the procedures to remove and replace the re-pickup assembly for duplex models.
Before you begin


Re-pickup assembly part number
RM2-6387-000CN Re-pickup assembly
Required tools


M477 models.



Step 3: Open the duplexer door

▲ Open the duplexer door.


cover (callout 1).
1
2

2
1
2



cover (callout 1).

cover.
1
2




reengaging.

cover (callout 1).
4 3 2 1

Remove the duplexer door (duplex models) on page 1187.

engaging.

cover (callout 1).
4 3
2 1

3
1

2 1
Step 8: Remove the duplexer door (duplex models)


Step 9: Remove the re-pickup assembly
1. On the left side of the printer, disconnect two connectors (callout 1), and then remove the cables
(callout 2) from the guides (callout 3).

Figure 1-2215 Disconnect two connectors and remove cables from guides
1
2
2. Lay the printer on the right side so that the left side is facing up. Remove six screws (callout 1).
Figure 1-2216 Remove six screws

3. Release four tabs (callout 1).
4. Remove the re-pickup assembly (callout 1).
Figure 1-2218 Remove the re-pickup assembly

Step 11: Install the re-pickup assembly
1. Position the foot on the printer (callout 1) through the opening (callout 2) on the re-pickup drive
assembly.
Figure 1-2220 Position the foot through the opening
1 2

2. Install four tabs (callout 1).
3. Install six screws (callout 1).
Figure 1-2222 Install six screws

4. Return the printer to an upright position so that the top side is facing up. On the left side of the printer,
connect two connectors (callout 1), and then install the cables (callout 2) in the guides (callout 3).
Figure 1-2223 Connect two connectors and install cables in guides
1
2
Step 12: Install the duplexer door (duplex models)
2
1

2
1

the retention arm.
2
1
3 4


2

top of the cover.
2
1

1 2 3 4

1
2

2
1
3 4




1 2
3 4
cover.
1
2

1
2

2
1


1
2


the duplexer door on page 1217.

2
1


1
2



Step 17: Close the duplexer door

▲ Close the duplexer door.




then close it.


Removal and replacement: Engine controller PCA
● Introduction
● Step 5: Remove the engine controller PCA
● Step 7: Install the engine controller PCA
Introduction
This document provides the procedures to remove and replace the engine controller PCA.
Before you begin

Engine controller PCA part number
RM2-7910-000CN Engine controller PCA (simplex models)
RM2-7909-000CN Engine controller PCA (duplex models)
Required tools





reengaging.
cover (callout 1).

4 3 2 1
Remove the engine controller PCA on page 1232.


engaging.
cover (callout 1).

4 3
2 1
3
1


2 1
Step 5: Remove the engine controller PCA
1. Duplex printers only: Before disconnecting the connectors in the next step, make note of the position of
two of the cables (callout 1).
cables will fit in either connector on the engine controller PCA. Make sure that these cables are installed
in the correct connectors. If the cables are switched, the printer will experience a repeatable jam when
printing duplex jobs.
Figure 1-2295 Check the cables

2. Disconnect all of the connectors on the engine controller PCA. Note that one connector (callout 1) is a
zero-insertion force (ZIF) connector. Lift the latch on the connector before removing the flat cable.
Figure 1-2296 Disconnect all of the connectors
3. Remove six screws (callout 1).

5. Remove the engine controller PCA.
Figure 1-2299 Remove the engine controller PCA

Step 7: Install the engine controller PCA
1. Position the engine controller PCA on the printer.
Figure 1-2301 Position the engine controller PCA


4. Connect all of the connectors on the engine controller PCA. Note that one connector (callout 1) is a zero-
insertion force (ZIF) connector. Lift the latch on the connector before installing the flat cable, and then
secure the latch once the cable is installed.
IMPORTANT: Duplex printers only: Two of the cables (callout 2) can be inadvertently switched when
reinstalling. The connectors on the cables will fit in either connector on the engine controller PCA. Make
sure that these cables are installed in the correct connectors. If these cables are switched, the printer
will experience a repeatable jam when printing duplex jobs.
Figure 1-2304 Connect all of the connectors
1
2
the left cover (M377, M477 models) on page 1241.

2
1
3 4

2

top of the cover.
2
1

1 2 3 4

1
2

2
1
3 4




1 2
3 4
cover.
1
2

1
2



then close it.


Removal and replacement: Lifter drive assembly
● Introduction
● Step 11: Remove the re-pickup assembly (duplex models)
● Step 12: Remove the lifter drive assembly
● Step 14: Install the lifter drive assembly
● Step 15: Install the re-pickup assembly (duplex models)
Introduction
This document provides the procedures to remove and replace the lifter drive assembly.

Before you begin
Lifter drive assembly part number
RM2-6370-000CN Lifter drive assembly
Required tools


M477 models.





cover (callout 1).

1
2

1
2



cover (callout 1).
cover.
1
2





reengaging.
cover (callout 1).

4 3 2 1


engaging.
cover (callout 1).

4 3
2 1
3
1


2 1


engine controller PCA on page 1275.



Step 11: Remove the re-pickup assembly (duplex models)
1
2


Step 12: Remove the lifter drive assembly
1. Remove four screws (callout 1), and then release the cables (callout 2) from the guides (callout 3).
Figure 1-2385 Remove four screws and release cables
1 2 3

2. Remove one cover (callout 1).
Figure 1-2386 Remove one cover

4. Remove the shaft.
Figure 1-2388 Remove the shaft
5. Lay the printer on the right side so that the left side is facing up. Locate the tray sensor switch
(callout 1).
Figure 1-2389 Locate the tray sensor switch

7. Release the tray sensor switch (callout 1), and then remove the cables (callout 2) from the guides
(callout 3).
Figure 1-2391 Release the tray sensor switch

8. Remove the tray sensor switch by releasing the cables (callout 1) through the printer frame.
Figure 1-2392 Remove the tray sensor switch
9. Remove the lifter drive assembly (callout 1), and then release the cables (callout 2) through the printer
frame.
Figure 1-2393 Remove the lifter drive assembly

Step 14: Install the lifter drive assembly
1. Install the cables (callout 1) on the lifter drive assembly up through the printer frame, and then install
the lifter drive assembly (callout 2).
Figure 1-2395 Install the lifter drive assembly

2. Install the cables (callout 1) on the tray sensor switch up through the printer frame.
Figure 1-2396 Install the tray sensor switch cable
3. Install the cables (callout 1) in the cable guide (callout 2), and then install the tray sensor switch
(callout 3) on the lifter drive assembly (callout 4).
Figure 1-2397 Install the tray sensor switch
1
4

4. Return the printer to an upright position so that the top side is facing up. Install the shaft (callout 1) into
the hole (callout 2) in the printer.
Figure 1-2398 Install the shaft
1 2

6. Install the tabs and slots on the cover (callout 1) into the corresponding tabs and slots (callout 2) on the
printer.
Figure 1-2400 Install one cover
2 1
7. Install four screws (callout 1), and then install the cables (callout 2) into the guides (callout 3).
Figure 1-2401 Install four screws and cables
1 2 3
Step 15: Install the re-pickup assembly (duplex models)
assembly.

1 2

1
2


1
2

2
1

2
1

the retention arm.
2
1
3 4


2

top of the cover.
2
1

1 2 3 4

1
2

2
1
3 4




1 2
3 4
cover.
1
2

1
2

2
1


1
2



2
1


1
2








then close it.

Removal and replacement: Pickup assembly
● Introduction
● Step 12: Remove the low-voltage power supply
● Step 16: Remove the pickup assembly
● Step 18: Install the pickup assembly
● Step 22: Install the low-voltage power supply

Introduction
This document provides the procedures to remove and replace the pickup assembly.
Before you begin

Pickup assembly part number
RM2-6372-000CN Pickup assembly
Required tools



M477 models.





cover (callout 1).
1
2

2
1
2



cover (callout 1).

cover.
1
2




reengaging.

cover (callout 1).
4 3 2 1


engaging.

cover (callout 1).
4 3
2 1

3
1

2 1






3 2

it.
Step 12: Remove the low-voltage power supply
(callout 3).
1
2



1
2

1 2

1
2
(callout 3).

1
2


1 2 3


(callout 1).

(callout 3).

frame.
Step 16: Remove the pickup assembly
1. Remove three screws (callout 1).

2. Release the cables (callout 1) from the cable guides (callout 2).
Figure 1-2544 Release the cables from the cable guides
3. Thread the cables (callout 1) through the opening in the driver PCA holder (callout 2).

4. Lay the printer on the right side so that the left side is facing up. Press the pickup and feed roller holder
(callout 1) toward the printer, and then remove the pickup assembly (callout 2).
Figure 1-2546 Remove the pickup assembly
5. Release the cables (callout 1) through the printer frame.

Step 18: Install the pickup assembly
1. Thread the cables (callout 1) through the printer frame.
Figure 1-2549 Thread the cables

2. Press the pickup and feed roller holder (callout 1) toward the printer, and then install the pickup
assembly (callout 2).
Figure 1-2550 Install the pickup assembly
3. Return the printer to an upright position so that the top side is facing up. Thread the cables (callout 1)
through the opening in the driver PCA holder (callout 2).
Figure 1-2551 Install the cable

4. Install the cables (callout 1) in the cable guides (callout 2).
Figure 1-2552 Install the cables in the cable guides
5. Install three screws (callout 1).


1
4
1 2

printer.
2 1

1 2 3
assembly.
1 2


1
2

2
1
Step 22: Install the low-voltage power supply
1 2
3 4

2
1



1
2

1
2
2
1

(callout 2).


1
2

2
1

2
1

the retention arm.
2
1
3 4


2

top of the cover.
2
1

1 2 3 4

1
2

2
1
3 4




1 2
3 4
cover.
1
2

1
2

2
1


1
2



2
1


1
2








then close it.

Removal and replacement: Front feed guide assembly
● Introduction
● Step 17: Remove the front feed guide assembly
● Step 19: Install the front feed guide assembly

Introduction
This document provides the procedures to remove and replace the front feed guide assembly.
Before you begin

Front feed guide assembly part number
RM2-6368-000CN Front feed guide assembly
Required tools



M477 models.





cover (callout 1).
1
2

2
1
2



cover (callout 1).

cover.
1
2




reengaging.

cover (callout 1).
4 3 2 1


engaging.

cover (callout 1).
4 3
2 1

3
1

2 1






3 2

it.
(callout 3).
1
2



1
2

1 2

1
2
(callout 3).

1
2


1 2 3


(callout 1).

(callout 3).

frame.


Step 17: Remove the front feed guide assembly
1. Release the cables (callout 1) from the cable guide (callout 2).

2
1
2. Lay the printer on the right side so that the left side is facing up. Press the tray 1 feed guide release
button (callout 1), and then release the tray 1 feed guide toward the front of the printer (callout 2).
Figure 1-2723 Release the tray 1 feed guide

3. Press the lever (callout 1) on the roller holder, and then slide the roller holder up (callout 2).
Figure 1-2724 Slide the roller holder
4. Hold the roller holder up (callout 1), and then lift the pickup and feed roller case (callout 2) up off of the
shafts (callout 3).
Figure 1-2725 Remove the pickup and feed rollers

5. Remove three screws (callout 1) on the rear feed guide assembly, and then remove three screws
(callout 2) on the front feed guide assembly.
Reinstallation tip: The three screws (callout 1) on the rear feed guide assembly are larger than the
screws on the front feed guide assembly.
1
2
6. Remove the roller holder (callout 1).
Figure 1-2727 Remove the roller holder

7. Remove the front feed guide assembly (callout 1). Release the cables (callout 2) through the printer
frame.
Figure 1-2728 Remove the front feed guide assembly
Step 19: Install the front feed guide assembly
1. Thread the cables (callout 1) on the front feed guide assembly up through the printer frame, and then
move the front feed guide assembly (callout 2) into position.

Figure 1-2730 Position the front feed guide assembly
2. Make sure that the flag (callout 1) on the front feed guide assembly fits in the opening (callout 2) in the
rear feed guide assembly.
Figure 1-2731 Position the flag
2
1

3. Install the holes on the front feed guide assembly (callout 1) over the tabs (callout 2) on the rear feed
guide assembly.
Figure 1-2732 Install the front feed guide assembly
2 1
4. Position the tabs (callout 1) on the roller holder in the slots (callout 2) in the rear feed guide assembly,
and then install the roller holder.
Figure 1-2733 Install the roller holder

5. Install three screws (callout 1) on the rear feed guide assembly, and then install three screws (callout 2)
on the front feed guide assembly.
1
2
6. Hold the roller holder up (callout 1), and then install the pickup and feed roller case (callout 2) on the
shafts (callout 3). Lower the roller holder until it snaps into place.

7. Return the printer to an upright position so that the top side is facing up. Install the cables (callout 1)
into the cable guide (callout 2).
2
1




1
4
1 2

printer.
2 1

1 2 3
assembly.
1 2


1
2

2
1
1 2
3 4

2
1



1
2

1
2
2
1

(callout 2).


1
2

2
1

2
1

the retention arm.
2
1
3 4


2

top of the cover.
2
1

1 2 3 4

1
2

2
1
3 4




1 2
3 4
cover.
1
2

1
2

2
1


1
2



2
1


1
2








then close it.

Removal and replacement: Rear feed guide assembly
● Introduction
● Step 18: Remove the rear feed guide assembly
● Step 20: Install the rear feed guide assembly

Introduction
This document provides the procedures to remove and replace the rear feed guide assembly.
Before you begin

Rear feed guide assembly part number
RM2-6366-000CN Rear feed guide assembly
Required tools



M477 models.





cover (callout 1).
1
2

2
1
2



cover (callout 1).

cover.
1
2




reengaging.

cover (callout 1).
4 3 2 1


engaging.

cover (callout 1).
4 3
2 1

3
1

2 1






3 2

it.
(callout 3).
1
2



1
2

1 2

1
2
(callout 3).

1
2


1 2 3


(callout 1).

(callout 3).

frame.



2
1

shafts (callout 3).

1
2

frame.
Step 18: Remove the rear feed guide assembly

▲ Remove the rear feed guide assembly (callout 1).
Figure 1-2917 Remove the rear feed guide assembly

Step 20: Install the rear feed guide assembly

▲ Install the rear feed guide assembly (callout 1).
Figure 1-2919 Install the rear feed guide assembly

2
1

guide assembly.
2 1

1
2

2
1




1
4
1 2

printer.
2 1

1 2 3
assembly.
1 2


1
2

2
1
1 2
3 4

2
1



1
2

1
2
2
1

(callout 2).


1
2

2
1

2
1

the retention arm.
2
1
3 4


2

top of the cover.
2
1

1 2 3 4

1
2

2
1
3 4




1 2
3 4
cover.
1
2

1
2

2
1


1
2



2
1


1
2








then close it.

Removal and replacement: Registration assembly
● Introduction
● Step 5: Remove the right cover ( M377, M477 models)
● Step 7: Remove the left cover ( M377, M477 models)
● Step 18: Remove the rear feed guide assembly
● Step 19: Remove the registration assembly
● Step 21: Install the registration assembly
● Step 22: Install the rear feed guide assembly

● Step 34: Install the left cover ( M377, M477 models)
● Step 36: Install the right cover ( M377, M477 models)
Introduction
This document provides the procedures to remove and replace the registration assembly.
Before you begin

Registration assembly part number
RM2-6374-000CN Registration assembly
Required tools



M477 models.



Remove the right cover ( M377, M477 models) on page 1615.


cover (callout 1).
1
2

2
1
2

Step 5: Remove the right cover ( M377, M477 models)


cover (callout 1).

cover.
1
2



Remove the left cover ( M377, M477 models) on page 1624.

reengaging.

cover (callout 1).
4 3 2 1

Step 7: Remove the left cover ( M377, M477 models)

engaging.

cover (callout 1).
4 3
2 1

3
1

2 1






3 2

it.
(callout 3).
1
2



1
2

1 2

1
2
(callout 3).

1
2


1 2 3


(callout 1).

(callout 3).

frame.



2
1

shafts (callout 3).

1
2

frame.
Step 18: Remove the rear feed guide assembly

Step 19: Remove the registration assembly

2. Squeeze the registration assembly (callout 1) to release five tabs (callout 2).
Figure 1-3109 Release five tabs
2
1

3. Remove the registration assembly (callout 1). Release the cables (callout 2) through the printer frame.
Figure 1-3110 Remove the registration assembly
Step 21: Install the registration assembly
1. Thread the cables (callout 1) on the registration assembly up through the printer frame, and then move
the registration assembly (callout 2) into position.

Figure 1-3112 Position the registration assembly
2. Install the tabs (callout 1) on the registration assembly in the slots (callout 2) in the printer frame.
1
2

3. Squeeze the registration assembly (callout 1) to install five tabs (callout 2).
Figure 1-3114 Install five tabs
2
1
4. Make sure that the tabs (callout 1) are installed correctly.
Step 22: Install the rear feed guide assembly

▲ Install the rear feed guide assembly (callout 1).


2
1
guide assembly.
2 1

1
2

2
1




1
4

1 2

printer.
2 1
1 2 3
assembly.

1 2

1
2

2
1

1 2
3 4
2
1




1
2

1
2
2
1

(callout 2).


1
2

2
1

2
1

the retention arm.
Install the left cover ( M377, M477 models) on page 1686.
2
1
3 4


2

top of the cover.
2
1

1 2 3 4

1
2
Step 34: Install the left cover ( M377, M477 models)

2
1
3 4




1 2
3 4
cover.
1
2

1
2

Install the right cover ( M377, M477 models) on page 1697.
2
1


1
2


Step 36: Install the right cover ( M377, M477 models)

2
1


1
2








then close it.

Removal and replacement: Memory PCA
● Introduction
● Step 7: Remove the rear top cover (simplex models)
● Step 8: Remove the integrated scanner assembly ( M377, M477 models)
● Step 10: Remove the top cover ( M377, M477 models)
● Step 12: Remove the memory PCA
● Step 14: Install the memory PCA
● Step 16: Install the top cover ( M377, M477 models)
● Step 18: Install the integrated scanner assembly ( M377, M477 models)
● Step 19: Install the rear top cover (simplex models)
Introduction
This document provides the procedures to remove and replace the memory PCA.

Before you begin
Memory PCA part number
RM2-7374-000CN Memory PCA
Required tools






cover (callout 1).
1
2

2
1
2



cover (callout 1).

cover.
1
2




reengaging.

cover (callout 1).
4 3 2 1

Remove the rear top cover (simplex models) on page 1728.

engaging.

cover (callout 1).
4 3
2 1

3
1

2 1
Step 7: Remove the rear top cover (simplex models)
integrated scanner assembly ( M377, M477 models) on page 1729.

Step 8: Remove the integrated scanner assembly ( M377, M477 models)
Remove the top cover (M452 models) on page 1743.

(callout 2).
1
2




2
1
NOTE: This step is for M477 fax models only. Skip this step for non-fax models.
2
3

remove it.
Step 10: Remove the top cover ( M377, M477 models)


(callout 2).
2 1


2
1




Remove the memory PCA on page 1748.
(callout 1).

(callout 1).
wireless PCA.
1
2

2 3 1

(callout 2).

(callout 2).

Step 12: Remove the memory PCA
1. Locate the memory PCA on the top of the printer.
Figure 1-3291 Locate the memory PCA

2. Disconnect two connectors (callout 1), remove one screw (callout 2), and then remove the memory PCA
(callout 3).
Figure 1-3292 Remove the memory PCA
3 2
Step 14: Install the memory PCA
1. Position the hole (callout 1) on the memory PCA over the post (callout 2) on the printer.

Figure 1-3294 Position the memory PCA
2. Install one screw (callout 1), and then connect two connectors (callout 2).
Figure 1-3295 Install the memory PCA
Install the top cover ( M377, M477 models) on page 1755.


(callout 2).
(callout 2).


(callout 2).
2 1

(callout 1).
PCA.
1
2
Step 16: Install the top cover ( M377, M477 models)
Install the rear top cover (simplex models) on page 1770.




2
1


correct position.

2 1

(callout 3).


1
2
Step 18: Install the integrated scanner assembly ( M377, M477 models)
Install the rear top cover (simplex models) on page 1770.

1
2



2
1

Step 19: Install the rear top cover (simplex models)
NOTE: This step is for simplex models. For duplex models, skip this step and go to Step 20: Install the left

2
1
3 4


2

top of the cover.
2
1

1 2 3 4

1
2

2
1
3 4




1 2
3 4
cover.
1
2

1
2

2
1


1
2



2
1


1
2





then close it.


Removal and replacement: Laser scanner (M452 models)
● Introduction
● Step 8: Remove the NFC PCA (M452dw model)
● Step 9: Remove the laser scanner (M452 models)
● Step 11: Install the laser scanner (M452 models)
● Step 12: Install the NFC PCA (M452dw model)
● Step 14: Install the top cover
Introduction
This document provides the procedures to remove and replace the laser scanner for the M452.
NOTE: The removal and replacement of the laser scanner is time-consuming and should be performed in a
clean environment to avoid introducing contaminants into the laser imaging system. For these reasons, HP
recommends replacing this part at an authorized repair center.
Before you begin


Laser scanner part number
RM2-5611-000CN Laser scanner
Required tools






cover (callout 1).
1
2

2
1
2


reengaging.

cover (callout 1).
4 3 2 1

NOTE: This step is for simplex models. For duplex models, skip this step and go to Step 6: Remove the top

(callout 1).

(callout 1).
wireless PCA.
1
2

2 3 1

(callout 2).

(callout 2).


(callout 3).
3 2
Step 8: Remove the NFC PCA (M452dw model)
NOTE: This step is for the M452dw model only. For all other models, skip this step and go to Step 9: Remove
the laser scanner (M452 models) on page 1813.
1. Remove one screw (callout 1), and then release one tab (callout 2).
Figure 1-3413 Remove one screw and release one tab
1
2

2. Disconnect one connector (callout 1), and then remove the NFC PCA.
Step 9: Remove the laser scanner (M452 models)
1. On the left side of the printer, on the formatter PCA, disconnect four connectors (callout 1).
Figure 1-3415 Disconnect four connectors

2. Lift the flat cable (callout 1) over to the right side of the printer to allow access to the cables under it.
Figure 1-3416 Lift the flat cable
3. Release all of the cables (callout 1) from the cable guides (callout 2).

4. Remove three screws (callout 1), and then remove the metal bracket (callout 2).

6. Remove the grounding plate (callout 1).
Figure 1-3420 Remove the grounding plate
7. M452dw only: Disconnect one connector (callout 1) on the walk-up USB port.

8. Remove the USB bracket (callout 1).
NOTE: The M452dw model is shown in the figure below. The walk-up USB port is attached to the USB
bracket for this model only.
Figure 1-3422 Remove the USB bracket

10. Remove the front door switch holder.
Figure 1-3424 Remove the front door switch holder
11. On the right side of the printer, toward the back, release one tab (callout 1) and then slide (callout 2) the
black cover toward the front of the printer.
Figure 1-3425 Release one tab on the cover



17. Remove the exhaust duct.
Figure 1-3431 Remove the exhaust duct

18. Use needle-nose pliers to release three springs (callout 1).
Figure 1-3432 Release three springs
TIP: Lift up the edge of the duct (callout 1) to release the right front spring (callout 2).
Figure 1-3433 Lift the duct to release the spring

19. Remove the laser scanner.
Figure 1-3434 Remove the laser scanner
Step 11: Install the laser scanner (M452 models)
1. Install three tabs (callout 1) on back of the laser scanner into the slots (callout 2) in the printer frame.

2
1
2. Install the five tabs (callout 1) on the bottom of the laser scanner into the holes (callout 2) in the top of
the printer.
TIP: Check the tabs by feeling along the underside of the sheet metal and verifying they are all fully
installed.

3. Before installing the springs in the next step, note the proper position of the springs when installed.
Figure 1-3438 Spring position
4. If the rear spring becomes dislodged from the printer frame, reposition it as shown below.
Figure 1-3439 Reposition the spring

5. Use needle-nose pliers to install three springs (callout 1).
Figure 1-3440 Install three springs
TIP: Lift up the edge of the duct (callout 1) to install the right front spring (callout 2).
Figure 1-3441 Lift the duct to install the spring

6. Position the exhaust duct on top of the printer.
Figure 1-3442 Position the exhaust duct
7. Install one tab (callout 1).

9. Position the cover on top of the printer.
Figure 1-3445 Position the cover

10. Install the tab (callout 1) on the cover in the slot (callout 2) in the printer frame and install the cover.

12. Install one tab (callout 1), and then slide the cover (callout 2) toward the back of the printer to install it.
Make sure that the tab (callout 3) slides under the sheet metal.
3
2
13. Position the front door switch holder on the printer.
Figure 1-3449 Position the front door switch holder

14. Position the spring on the switch holder over the lever on the laser scanner (callout 1), and then install
one screw (callout 2).
Figure 1-3450 Position the spring and install one screw
1
2
15. Install the tabs (callout 1) on the USB bracket in the slots (callout 2) on the printer.
NOTE: The M452dw model is shown in the figure below. The walk-up USB port is attached to the USB
bracket for this model only.
Figure 1-3451 Install the USB bracket

16. M452dw only: Connect one connector (callout 1) on the walk-up USB port.
17. Install the tab on the grounding plate (callout 1) in the slot (callout 2) in the printer frame.
Figure 1-3453 Install the grounding plate

19. Position the metal bracket (callout 1) on top of the printer, and then install three screws (callout 2).

20. Install all of the cables (callout 1) into the cable guides (callout 2).
21. Position the flat cable (callout 1) over the top of the printer.
Figure 1-3457 Position the flat cable

22. On the left side of the printer, on the formatter PCA, connect four connectors (callout 1).
Figure 1-3458 Connect four connectors
Step 12: Install the NFC PCA (M452dw model)
NOTE: This step is for the M452dw model only. For all other models, skip this step and go to Step 13: Install
the memory PCA on page 1836.
1. Connect one connector (callout 1), and then remove the NFC PCA.

2. Position the slots (callout 1) on the NFC PCA over the tabs (callout 2) on the printer.
Figure 1-3460 Position the NFC PCA
3. Install one tab (callout 1), and then install one screw (callout 2).
Figure 1-3461 Install one tab and one screw
2
1

Step 14: Install the top cover


(callout 2).
(callout 2).


(callout 2).
2 1

(callout 1).
PCA.
1
2


2
1
3 4

2

top of the cover.
2
1

1 2 3 4

1
2

2
1


1
2




then close it.


Removal and replacement: Laser scanner ( M377, M477 models)
● Introduction
● Step 10: Remove the NFC PCA (M477fdw model)
● Step 11: Remove the laser scanner ( M377, M477 models)
● Step 13: Install the laser scanner ( M377, M477 models)
● Step 14: Install the NFC PCA (M477fdw model)
Introduction
This document provides the procedures to remove and replace the laser scanner for the M477.
NOTE: The removal and replacement of the laser scanner is time-consuming and should be performed in a
clean environment to avoid introducing contaminants into the laser imaging system. For these reasons, HP
recommends replacing this part at an authorized repair center.

Before you begin
Laser scanner part number
RM2-5611-000CN Laser scanner
Required tools






cover (callout 1).

cover.
1
2





engaging.
cover (callout 1).

4 3
2 1
3
1


2 1
integrated scanner assembly ( M377, M477 models) on page 1870.


(callout 2).
1
2



2
1

2
3
remove it.


(callout 2).
2 1



2
1




(callout 3).
3 2
Step 10: Remove the NFC PCA (M477fdw model)
NOTE: This step is for the M477fdw model only. For all other models, skip this step and go to Step 11:
Remove the laser scanner ( M377, M477 models) on page 1885.

1
2
Step 11: Remove the laser scanner ( M377, M477 models)
1. On the left side of the printer, on the formatter PCA, disconnect four connectors (callout 1).

Figure 1-3556 Disconnect four connectors
2. Lift the flat cable (callout 1) over to the right side of the printer to allow access to the cables under it.
Figure 1-3557 Lift the flat cable

3. Release all of the cables (callout 1) from the cable guides (callout 2).
4. On the right side of the printer, remove one screw (callout 1).

5. On the left side of the printer on top, remove two screws (callout 1). On the right side of the printer on
top, remove two screws (callout 2).
Reinstallation tip: The screws on the left (callout 1) are a different type of screw than the screws on
the right. When reinstalling the screws, make sure they are in the correct position.
Figure 1-3560 Remove four screws
2
1
6. Release the cables (callout 1) through the opening in the bracket (callout 2).
2
1

7. Remove the metal bracket (callout 1).
Figure 1-3562 Remove the metal bracket

9. Remove the front door switch holder.
Figure 1-3564 Remove the front door switch holder
10. On the right side of the printer, toward the back, release one tab (callout 1) and then slide (callout 2) the
black cover toward the front of the printer.
Figure 1-3565 Release one tab on the cover



16. Remove the exhaust duct.
Figure 1-3571 Remove the exhaust duct

17. Use needle-nose pliers to release three springs (callout 1).
Figure 1-3572 Release three springs
TIP: Lift up the edge of the duct (callout 1) to release the right front spring (callout 2).
Figure 1-3573 Lift the duct to release the spring

18. Remove the laser scanner.
Figure 1-3574 Remove the laser scanner
Step 13: Install the laser scanner ( M377, M477 models)
1. Install three tabs (callout 1) on back of the laser scanner into the slots (callout 2) in the printer frame.

2
1
2. Install the five tabs (callout 1) on the bottom of the laser scanner into the holes (callout 2) in the top of
the printer.
TIP: Check the tabs by feeling along the underside of the sheet metal and verifying they are all fully
installed.

3. Before installing the springs in the next step, note the proper position of the springs when installed.
Figure 1-3578 Spring position
4. If the rear spring becomes dislodged from the printer frame, reposition it as shown below.

5. Use needle-nose pliers to install three springs (callout 1).
Figure 1-3580 Install three springs
TIP: Lift up the edge of the duct (callout 1) to install the right front spring (callout 2).
Figure 1-3581 Lift the duct to install the spring

6. Position the exhaust duct on top of the printer.
Figure 1-3582 Position the exhaust duct
7. Install one tab (callout 1).


10. Install the tab (callout 1) on the cover in the slot (callout 2) in the printer frame and install the cover.

12. Install one tab (callout 1), and then slide the cover (callout 2) toward the back of the printer to install it.
Make sure that the tab (callout 3) slides under the sheet metal.
3
2
13. Position the front door switch holder on the printer.
Figure 1-3589 Position the front door switch holder

14. Position the spring on the switch holder over the lever on the laser scanner (callout 1), and then install
one screw (callout 2).
Figure 1-3590 Position the spring and install one screw
1
2
15. Position the metal bracket (callout 1) on top of the printer.
Figure 1-3591 Position the metal bracket

16. On the right side of the printer, position the slots (callout 1) on the metal bracket over the edge
(callout 2) of the printer frame.
Figure 1-3592 Install the metal bracket
17. Insert the cables (callout 1) through the opening in the bracket (callout 2).
Figure 1-3593 Insert the cables
2
1

18. On the left side of the printer on top, install two screws (callout 1). On the right side of the printer on top,
install two screws (callout 2).
TIP: The screws on the left (callout 1) are a different type of screw than the screws on the right. When
reinstalling the screws, make sure they are in the correct position.
Figure 1-3594 Install four screws
2
1
19. On the right side of the printer, install one screw (callout 1).

20. Install all of the cables (callout 1) into the cable guides (callout 2).
21. Position the flat cable (callout 1) over the top of the printer.
Figure 1-3597 Position the flat cable

22. On the left side of the printer, on the formatter PCA, connect four connectors (callout 1).
Figure 1-3598 Connect four connectors
Step 14: Install the NFC PCA (M477fdw model)
NOTE: This step is for the M477fdw model only. For all other models, skip this step and go to Step 15: Install
the memory PCA on page 1908.

2
1





2
1


correct position.

2 1

(callout 3).


1
2

1
2



2
1

cover ( M377, M477 models) on page 1925.

2
1
3 4




1 2
3 4
cover.
1
2

1
2

2
1


1
2






then close it.

Removal and replacement: Fuser (simplex models)
● Introduction
● Step 7: Remove the rear top cover (simplex models)
● Step 8: Remove the integrated scanner assembly (M477 models)
● Step 12: Remove the fuser (simplex models)
● Step 14: Install the fuser (simplex models)
● Step 18: Install the integrated scanner assembly (M477 models)
● Step 19: Install the rear top cover (simplex models)
Introduction
This document provides the procedures to remove and replace the fuser for simplex models.

Before you begin
Fuser part number
RM2-6431-000CN Fuser (110V simplex)
RM2-6436-000CN Fuser (220V simplex)
Required tools





cover (callout 1).

1
2

1
2



cover (callout 1).
cover.
1
2





reengaging.
cover (callout 1).

4 3 2 1
rear top cover (simplex models) on page 1959.


engaging.
cover (callout 1).

4 3
2 1
3
1


2 1
Step 7: Remove the rear top cover (simplex models)

Step 8: Remove the integrated scanner assembly (M477 models)
top cover (M452 models) on page 1973.

(callout 2).
1
2



2
1

2
3
remove it.


(callout 2).
2 1



2
1



fuser (simplex models) on page 1978.
(callout 1).

(callout 1).

wireless PCA.
1
2
2 3 1


(callout 2).
(callout 2).

Step 12: Remove the fuser (simplex models)
1. Disconnect one connector (callout 1) on the engine controller PCA.
NOTE: This connector is a zero-insertion force (ZIF) connector. Lift the latch on the connector before
removing the flat cable.

2. Disconnect six connectors on the engine controller PCA (callout 1), and then remove the cables
Figure 1-3740 Disconnect six connectors

3. Disconnect one connector (callout 1). Release the connector latch, and then disconnect one connector
(callout 2). Remove the cables (callout 3) from the guides (callout 4).
2
1
4
3
4. Remove five screws.
Figure 1-3742 Remove five screws

5. Remove the fuser.
Figure 1-3743 Remove the fuser
Step 14: Install the fuser (simplex models)
1. Position the fuser on the printer.

Figure 1-3745 Position the fuser
2. Install five screws.
Figure 1-3746 Install five screws

3. Connect two connectors (callout 1), and then install the cables (callout 2) in the guides (callout 3).
3
2
4. Connect six connectors on the engine controller PCA (callout 1), and then install the cables (callout 2) in
the guides (callout 3).
Figure 1-3748 Connect six connectors

5. Connect one connector (callout 1) on the engine controller PCA.
installing the flat cable and then lower the latch to secure the cable.

(callout 2).

(callout 2).

(callout 2).
2 1

(callout 1).

PCA.
1
2




2
1

correct position.


2 1
(callout 3).


1
2

Step 18: Install the integrated scanner assembly (M477 models)
1
2




2
1
Step 19: Install the rear top cover (simplex models)


2
1
3 4

2

top of the cover.
2
1

1 2 3 4

1
2

2
1
3 4




1 2
3 4
cover.
1
2

1
2

2
1


1
2



2
1


1
2





then close it.

Removal and replacement: Fuser (duplex models)
● Introduction
● Step 11: Remove the fuser (duplex models)
● Step 13: Install the fuser (duplex models)
Introduction
This document provides the procedures to remove and replace the fuser for duplex models.

Before you begin
Fuser part number
RM2-6418-000CN Fuser (110V duplex)
RM2-6435-000CN Fuser (220V duplex)
Required tools





cover (callout 1).

1
2

1
2



cover (callout 1).
cover.
1
2





reengaging.
cover (callout 1).

4 3 2 1


engaging.
cover (callout 1).

4 3
2 1
3
1


2 1

(callout 2).
1
2



2
1

2
3
remove it.


(callout 2).
2 1



2
1



Remove the fuser (duplex models) on page 2065.
(callout 1).

(callout 1).

wireless PCA.
1
2
2 3 1


(callout 2).
(callout 2).

Step 11: Remove the fuser (duplex models)
1. Remove four screws (callout 1), and then release one tab (callout 2).

2. Remove the guide (callout 1).

4. Disconnect eight connectors on the engine controller PCA (callout 1), and then remove the cables
Figure 1-3912 Disconnect eight connectors
3
2

1 2
4
3
6. Remove three screws.

Step 13: Install the fuser (duplex models)
1. Position the fuser on the printer. When installing the fuser, make sure that the switchback lever
(callout 1) is installed completely through the opening (callout 2) in the printer frame.

Figure 1-3917 Install the lever through the opening
1
2
2. The fingers on the switchback lever will fit around the shaft (callout 1) inside the printer.
Figure 1-3918 Switchback lever shaft

3. The figure below shows a cross section view of the proper position of the switchback lever (callout 1)
around the shaft (callout 2).
Figure 1-3919 Switchback lever position
2
1
4. Install three screws.

3
2
6. Connect eight connectors on the engine controller PCA (callout 1), and then install the cables (callout 2)
in the guides (callout 3).
Figure 1-3922 Connect eight connectors
3
2

8. Position the guide (callout 1) on the printer.
Figure 1-3924 Position the guide

9. Install one tab (callout 1), and then install four screws (callout 2).
Install the top cover ( M377, M477 models) on page 2079.

(callout 2).

(callout 2).

(callout 2).
2 1

(callout 1).

PCA.
1
2
Install the left cover (M452 models) on page 2093.




2
1

correct position.


2 1
(callout 3).


1
2

1
2




2
1

2
1
3 4

2

top of the cover.
2
1

1 2 3 4

1
2

2
1
3 4




1 2
3 4
cover.
1
2

1
2

2
1


1
2



2
1


1
2





then close it.

Removal and replacement: Fuser power supply
● Introduction
● Step 5: Remove the fuser power supply
● Step 7: Install the fuser power supply
Introduction
This document provides the procedures to remove and replace the fuser power supply
Before you begin

Fuser power supply part numbers
RM2-6440-000CN Fuser power supply (110V)
RM2-6441-000CN Fuser power supply (220V)
Required tools





cover (callout 1).

1
2

1
2

Remove the fuser power supply on page 2129.


cover (callout 1).
cover.
1
2




Step 5: Remove the fuser power supply
1 2 4

Reinstallation tip: The lower screw (callout 2) is shorter than the other screw. Make sure that this
screw is reinstalled in the correct position.
1
2
3. Duplex models only: Remove one screw (callout 1), and then release the retainer arm (callout 2).
Figure 1-4035 Release the retainer arm

(callout 2). Remove three screws (callout 3).
Reinstallation tip: The screw on the driver PCA (callout 4) is different from the other screws. Make
sure that this screw is reinstalled in the correct position.
Figure 1-4036 Disconnect two connectors and remove three screws
2
4
5. Release one tab (callout 1) on the back of the fuser power supply from the slot (callout 2) in the printer
frame. Rotate the fuser power supply away from the printer to remove it (callout 3).
Figure 1-4037 Remove the fuser power supply
2
1

Step 7: Install the fuser power supply
1. Install the tab (callout 1) on the fuser power supply into the slot (callout 2) in the printer. Make sure that
the metal tab (callout 3) on the fuser power supply fits behind the edge of the driver PCA (callout 4).
2
1
4
3

2. Install the tab (callout 1) on the back of the fuser power supply into the slot (callout 2) in the printer
frame.
2
1
3. Install three screws (callout 1), and then connect two connectors (callout 2).
2
1

4. Duplex models only: Position the retainer arm (callout 1) on the printer frame, and then install one
screw (callout 2).
Figure 1-4042 Install the retainer arm
1
2

6. Connect two connectors (callout 1), and then install the cables (callout 2) into the guides (callout 3).
1 3
the right cover ( M377, M477 models) on page 2139.
2
1


1
2



2
1


1
2





then close it.


Removal and replacement: Fuser motor
● Introduction
● Step 6: Remove the fuser motor
● Step 8: Install the fuser motor
Introduction
This document provides the procedures to remove and replace the fuser motor.
Before you begin

Fuser motor part number
RM2-7348-000CN Fuser motor
Required tools





cover (callout 1).

1
2

1
2

Remove the fuser power supply on page 2161.


cover (callout 1).
cover.
1
2




1 2 4

1
2

2
4
2
1
Step 6: Remove the fuser motor

▲ Disconnect one connector (callout 1), remove four screws (callout 2), and then remove the fuser motor
(callout 3).

Figure 1-4099 Remove the fuser motor
1 3
Step 8: Install the fuser motor

▲ Position the fuser motor on the printer (callout 1). Install four screws (callout 2), and then connect one

Figure 1-4101 Install the fuser motor
3 1
2
1
4
3

frame.
2
1
2
1

screw (callout 2).
1
2

1 3
2
1


1
2



2
1


1
2





then close it.


Removal and replacement: Duplex drive assembly (duplex models)
● Introduction
● Step 7: Remove the integrated scanner assembly (M377, M477 models)
● Step 11: Remove the fuser (duplex models)
● Step 13: Remove the duplex drive assembly
● Step 15: Install the duplex drive assembly
● Step 17: Install the fuser (duplex models)
● Step 21: Install the integrated scanner assembly (M377, M477 models)
Introduction
This document provides the procedures to remove and replace the duplex drive assembly for duplex models.

Before you begin
Duplex drive assembly part number
RM2-6389-000CN Duplex drive assembly
Required tools





cover (callout 1).

1
2

1
2



cover (callout 1).
cover.
1
2





reengaging.
cover (callout 1).

4 3 2 1


engaging.
cover (callout 1).

4 3
2 1
3
1


2 1
Step 7: Remove the integrated scanner assembly (M377, M477 models)

(callout 2).
1
2



2
1

2
3
remove it.


(callout 2).
2 1



2
1



Remove the fuser (duplex models) on page 2219.
(callout 1).

(callout 1).

wireless PCA.
1
2
2 3 1


(callout 2).
(callout 2).

Step 11: Remove the fuser (duplex models)
1. Remove four screws (callout 1), and then release one tab (callout 2).

2. Remove the guide (callout 1).

4. Disconnect eight connectors on the engine controller PCA (callout 1), and then remove the cables
Figure 1-4210 Disconnect eight connectors
3
2

1 2
4
3
6. Remove three screws.

1 2 4

1
2

2
4
2
1
Step 13: Remove the duplex drive assembly

2. Rotate the duplex drive assembly (callout 1) away from the printer to remove it.
Figure 1-4220 Remove the duplex drive assembly

Step 15: Install the duplex drive assembly
1. Install the tab (callout 1) on the duplex drive assembly in the slot (callout 2) on the printer.

2. Rotate the duplex drive assembly toward the printer to install it.
Figure 1-4223 Install the duplex drive assembly
2
1
4
3

frame.
2
1
2
1

screw (callout 2).
1
2

1 3
Step 17: Install the fuser (duplex models)
1. Position the fuser on the printer. When installing the fuser, make sure that the switchback lever
(callout 1) is installed completely through the opening (callout 2) in the printer frame.
Figure 1-4230 Install the lever through the opening
1
2

2. The fingers on the switchback lever will fit around the shaft (callout 1) inside the printer.
Figure 1-4231 Switchback lever shaft
3. The figure below shows a cross section view of the proper position of the switchback lever (callout 1)
around the shaft (callout 2).
Figure 1-4232 Switchback lever position
2
1

4. Install three screws.
3
2

6. Connect eight connectors on the engine controller PCA (callout 1), and then install the cables (callout 2)
in the guides (callout 3).
Figure 1-4235 Connect eight connectors
3
2

8. Position the guide (callout 1) on the printer.
Figure 1-4237 Position the guide
9. Install one tab (callout 1), and then install four screws (callout 2).
Install the top cover (M377, M477 models) on page 2240.


(callout 2).
(callout 2).


(callout 2).
2 1

(callout 1).
PCA.
1
2




2
1


correct position.

2 1

(callout 3).


1
2
Step 21: Install the integrated scanner assembly (M377, M477 models)

1
2



2
1

2
1
3 4


2

top of the cover.
2
1

1 2 3 4

1
2

2
1
3 4




1 2
3 4
cover.
1
2

1
2

2
1


1
2



2
1


1
2





then close it.

Removal and replacement: Wireless antenna (M452nw/dw models)
● Introduction
● Step 7: Remove the wireless antenna (M452nw/dw models)
● Step 9: Install the wireless antenna (M452nw/dw models)
Introduction
This document provides the procedures to remove and replace the wireless antenna for the M452nw and
M452dw.
Before you begin

Wireless antenna part number
0960-3467 Remote antenna (M452nw/dw model)
Required tools





cover (callout 1).

1
2

1
2


reengaging.
cover (callout 1).

4 3 2 1
NOTE: This step is for simplex models. For duplex models, skip this step and go to Step 6: Remove the top

(callout 1).

(callout 1).

wireless PCA.
1
2
2 3 1


(callout 2).
(callout 2).

Step 7: Remove the wireless antenna (M452nw/dw models)
1. On the underside of the top cover, locate the wireless antenna (callout 1).
NOTE: The M452dw model is shown in the figures below. The procedure is also correct for the M452nw
model.

Figure 1-4351 Locate the wireless antenna
2. Loosen one edge of the tape holding down the antenna cable (callout 1).
NOTE: Do not completely remove the tape. It will be used to secure the cable on the replacement
antenna.
Figure 1-4352 Loosen the tape

3. Lift the edge of the silver tape, and then peel the antenna off of the top cover.
NOTE: Remove any adhesive residue that remains on the top cover after removing the antenna.
Figure 1-4353 Remove the antenna
Step 9: Install the wireless antenna (M452nw/dw models)
1. On the back of the antenna at the top edge, peel the protective backing off of the adhesive strip.

Figure 1-4355 Remove protective backing from adhesive strip
2. Position the antenna on the top cover, and then press along the top edge to make sure that the adhesive
strip is securely in place.
Figure 1-4356 Install the top adhesive strip

3. Begin peeling the silver tape up and away from the protective backing.
Figure 1-4357 Peel the silver tape up
4. Peel the silver tape (callout 1) all the way up, and then remove the protective backing (callout 2).
Figure 1-4358 Remove the protective backing
1
2

5. Press the entire surface of the silver tape down to make sure it is securely attached to the top cover.
Figure 1-4359 Press the silver tape
6. Position the tape over the antenna cable to hold it securely against the top cover.
NOTE: If the tape is missing, use a small piece of electrical tape to secure the antenna to the top cover
at the location shown.
Figure 1-4360 Position the tape

7. Remove the protective cover (callout 1) from the end of the antenna cable.
Figure 1-4361 Remove the protective cover

(callout 2).

(callout 2).

(callout 2).
2 1

(callout 1).

PCA.
1
2

2
1
3 4


2

top of the cover.
2
1

1 2 3 4

1
2

2
1


1
2




then close it.


Removal and replacement: Wireless PCA (M452nw/dw models)
● Introduction
● Step 4: Remove the formatter PCA
● Step 5: Remove the wireless PCA (M452nw/dw models)
● Step 7: Install the wireless PCA (M452nw/dw models)
● Step 8: Install the formatter PCA
Introduction
This document provides the procedures to remove and replace the wireless PCA for the M452nw and M452dw.
Before you begin

Wireless PCA part numbers
0960-3295 Wireless PCA (M542nw/dw)
Required tools






reengaging.
cover (callout 1).

4 3 2 1
Step 4: Remove the formatter PCA
NOTE: The M452dw model is shown in the figures below. The formatter PCA on other models might look
differently and have a different number of connections. However, the procedure is correct for all models.
1. Disconnect all of the connectors on the formatter PCA.

Figure 1-4405 Disconnect all of the connectors)
2. Remove four screws (callout 1).

3. Disconnect the antenna (callout 1) from the connector (callout 2).
1
2
4. Slide the formatter PCA to the right to release the ports (callout 1) from the openings in the printer
frame (callout 2), and then remove the formatter PCA.
Figure 1-4408 Remove the formatter PCA
2 1
Step 5: Remove the wireless PCA (M452nw/dw models)

▲ Lay the formatter PCA on a flat surface. Release two tabs (callout 1), and then lift the wireless PCA up
(callout 2) to release it from the bracket and disconnect it from the formatter PCA.

Figure 1-4409 Remove the wireless PCA
Step 7: Install the wireless PCA (M452nw/dw models)
1. Position the holes (callout 1) on the wireless PCA over the posts (callout 2) on the bracket.

Figure 1-4411 Position the wireless PCA
2. Press the connector on the wireless PCA onto the connector on the formatter PCA.
Figure 1-4412 Connect the wireless PCA

3. Make sure that two tabs (callout 1) snap into place.
Step 8: Install the formatter PCA
1. Install the ports (callout 1) on the side of the formatter PCA through the openings in the printer frame
(callout 2).
Figure 1-4414 Position the formatter PCA ports
2 1

2. Connect the antenna (callout 1) to the connector (callout 2).
1
2
3. Set the formatter PCA in place, and then install four screws (callout 1).

4. Connect all connectors on the formatter PCA.
2
1
3 4


2

top of the cover.
2
1

1 2 3 4

1
2



then close it.

Removal and replacement: Wireless PCA (M377, M477fnw/fdw models)
● Introduction
● Step 4: Remove the wireless PCA (M377, M477fnw/fdw models)
● Step 6: Install the wireless PCA (M377, M477fnw/fdw models)
Introduction
This document provides the procedures to remove and replace the wireless PCA for the M377, M477fnw and
M477fdw.
Before you begin

Wireless PCA part numbers
1150-7940 Wireless PCA (M377, M477fnw/fdw)
Required tools






engaging.

cover (callout 1).
4 3
2 1

3
1

2 1
Step 4: Remove the wireless PCA (M377, M477fnw/fdw models)
1. Disconnect one connector on the formatter PCA (callout 1).

2. Slide the wireless PCA holder (callout 1) toward the front of the printer.
Figure 1-4445 Slide the wireless PCA holder forward

3. Rotate the wireless PCA holder away from the printer to remove it.
Figure 1-4446 Remove the wireless PCA holder

5. Loosen the cable (callout 1) in the holder by feeding it partially through the holder opening. Release the
cable from the guides (callout 2).
Figure 1-4448 Release the cable
6. Feed the cable (callout 1) all the way through the opening in the holder.
Figure 1-4449 Feed the cable through the holder

7. Release the cable (callout 1) from the guide (callout 2) on the holder, and then slide the wireless PCA to
the right (callout 3) to remove it from the holder.
Figure 1-4450 Remove the wireless PCA from the holder

Step 6: Install the wireless PCA (M377, M477fnw/fdw models)
1. Position the cable so that the red wires on the connector (callout 1) are on the side of the PCA close to
the hole (callout 2) where the screw will be installed. Install the connector on the cable (callout 3) into
the connector on the wireless PCA (callout 4).
1
3
2

2. Install the cable (callout 1) under the guide (callout 2) on the holder. Align the notch (callout 3) on the
wireless PCA with the tab (callout 4) on the holder, and then slide the wireless PCA onto the holder.
Figure 1-4454 Install the wireless PCA on the holder
1 3
3. Feed the cable (callout 1) partially through the opening in the holder
Figure 1-4455 Feed the cable through the holder

4. Install the cable (callout 1) in the guides (callout 2), and then pull the cable (callout 3) through the
opening until it is completely installed in the holder.
2
1
3

6. Rotate the wireless PCA holder (callout 1) into the opening (callout 2) on the printer. Install the edge of
the wireless PCA holder (callout 3) over the edge (callout 4) of the sheet metal bracket.
Figure 1-4458 Install the wireless PCA holder
2 1
4
3
7. Slide the wireless PCA holder (callout 1) toward the back of the printer.
Figure 1-4459 Slide the wireless PCA holder

8. Position the wireless PCA cable (callout 1) behind the USB cable (callout 2), and then connect one
1
2
2
1
3 4




1 2
3 4
cover.
1
2

1
2



then close it.


Removal and replacement: Formatter PCA
● Introduction
● Step 5: Remove the formatter PCA
● Step 7: Install the formatter PCA
Introduction
This document provides the procedures to remove and replace the formatter PCA.
Before you begin

Formatter PCA part number
CF388-60003 Formatter PCA (M452nw)
CF388-67018 Formatter PCA (M452nw; China only)
CF389-60002 Formatter PCA (M452dn)
CF389-67018 Formatter PCA (M452dn; China only)
CF394-60002 Formatter PCA (M452dw)
CF394-67018 Formatter PCA (M452dw; China only)
CF377-60001 Formatter PCA (M477fnw)
CF377-67018 Formatter PCA (M477fnw; China only)

Formatter PCA part number
CF378-60002 Formatter PCA (M477fdn)
CF378-67018 Formatter PCA (M477fdn; China only)
CF379-60003 Formatter PCA (M477fdw)
CF379-67018 Formatter PCA (M477fdw; China only)
CF378-67902 Formatter PCA (M377dw)
CF378-67901 Formatter PCA (M377dw; China only)
Required tools





reengaging.

cover (callout 1).
4 3 2 1

Remove the formatter PCA on page 2371.

engaging.

cover (callout 1).
4 3
2 1

3
1

2 1
Step 5: Remove the formatter PCA
1. Disconnect all of the connectors on the formatter PCA.

Figure 1-4496 Disconnect all of the connectors)

3. M452nw and M452dw only: Disconnect the antenna (callout 1) from the connector (callout 2).
1
2
4. Slide the formatter PCA to the right to release the ports (callout 1) from the openings in the printer
frame (callout 2), and then remove the formatter PCA.
Figure 1-4499 Remove the formatter PCA
2 1

5. M452nw and M452dw only: Lay the formatter PCA on a flat surface. Release two tabs (callout 1), and
then lift the wireless PCA up (callout 2) to release it from the bracket and disconnect it from the
formatter PCA.
NOTE: Set the wireless PCA aside to be installed on the replacement formatter PCA.
Figure 1-4500 Remove the wireless PCA
6. M452nw and M452dw only: Press down to release one tab (callout 1) on the back of the formatter PCA
while lifting up to release a second tab (callout 2). Slide the bracket to the right (callout 3) to remove it
from the formatter PCA.
NOTE: Set the bracket aside to be installed on the replacement formatter PCA.

Step 7: Install the formatter PCA
1. M452nw and M452dw only: To install the wireless bracket from the old formatter PCA onto the new
formatter PCA, position the tabs (callout 1) on the bracket into the holes (callout 2) on the formatter
PCA. Slide the bracket to the left (callout 3) until the tabs snap into place.
1
2

2. M452nw and M452dw only: Position the holes (callout 1) on the wireless PCA over the posts (callout 2)
on the bracket.
Figure 1-4504 Position the wireless PCA
3. M452nw and M452dw only: Press the connector on the wireless PCA onto the connector on the
formatter PCA.
Figure 1-4505 Connect the wireless PCA

4. M452nw and M452dw only: Make sure that two tabs (callout 1) snap into place.
5. Install the ports (callout 1) on the side of the formatter PCA through the openings in the printer frame
(callout 2).
Figure 1-4507 Position the formatter PCA ports
2 1

6. M452nw and M452dw only: Connect the antenna (callout 1) to the connector (callout 2).
1
2
7. Set the formatter PCA in place, and then install four screws (callout 1).

8. Connect all connectors on the formatter PCA.
2
1
3 4


2

top of the cover.
2
1

1 2 3 4

1
2

2
1
3 4




1 2
3 4
cover.
1
2

1
2



then close it.


Removal and replacement: Environmental sensor
● Introduction
● Step 5: Remove the environmental sensor
● Step 7: Install the environmental sensor
Introduction
This document provides the procedures to remove and replace the environmental sensor.
Before you begin

Environmental sensor part number
RM2-7376-000CN Environmental sensor
Required tools






reengaging.
cover (callout 1).

4 3 2 1
Remove the environmental sensor on page 2403.


engaging.
cover (callout 1).

4 3
2 1
3
1


2 1
Step 5: Remove the environmental sensor
1. On the left side of the printer, disconnect one connector (callout 1), and then release two tabs
(callout 2).
Figure 1-4554 Disconnect one connector and release two tabs

1

2. Disconnect one connector (callout 1), and then remove the environmental sensor.
Figure 1-4555 Disconnect one connector and remove the sensor
Step 7: Install the environmental sensor
1. If the spring (callout 1) becomes dislodged, reposition it as shown below.


3. On the left side of the printer, install two tabs (callout 1), and then connect one connector (callout 2).
Figure 1-4559 Install two tabs and connect one connector

2
2
1
3 4


2

top of the cover.
2
1

1 2 3 4

1
2

2
1
3 4




1 2
3 4
cover.
1
2

1
2



then close it.


Removal and replacement: Fax PCA (M477 models)
● Introduction
● Step 9: Install the integrated scanner assembly (M477models)
Introduction
This document provides the procedures to remove and replace the fax PCA.
Before you begin

Fax PCA part number
CF206-60001 Fax PCA (United States)
CF207-60001 FAX PCA (Europe)
CF208-60001 FAX PCA (Brazil)
Required tools






cover (callout 1).
cover.
1
2





engaging.

cover (callout 1).
4 3
2 1

3
1

2 1

(callout 2).
1
2




2
1
2
3

remove it.


1
2
Step 9: Install the integrated scanner assembly (M477models)

1
2



2
1

2
1
3 4




1 2
3 4
cover.
1
2

1
2

2
1


1
2






then close it.

Removal and replacement: NFC PCA (M452dw and M477dw models)
● Introduction
● Step 11: Remove the NFC PCA (M452dw and M477dw models)
● Step 13: Install the NFC PCA (M452dw and M477dw models)
● Step 17: Install the integrated scanner assembly (M477 models)
Introduction
This document provides the procedures to remove and replace the NFC PCA.

Before you begin
NFC PCA part number
B4K93-60001 NFC PCA
Required tools





cover (callout 1).

1
2

1
2



cover (callout 1).
cover.
1
2





reengaging.
cover (callout 1).

4 3 2 1


engaging.
cover (callout 1).

4 3
2 1
3
1


2 1

(callout 2).
1
2



2
1

2
3
remove it.


(callout 2).
2 1



2
1



NFC PCA (M452dw and M477dw models) on page 2498.
(callout 1).

(callout 1).

wireless PCA.
1
2
2 3 1


(callout 2).
(callout 2).

Step 11: Remove the NFC PCA (M452dw and M477dw models)

1
2

Step 13: Install the NFC PCA (M452dw and M477dw models)

2
1


(callout 2).
(callout 2).


(callout 2).
2 1

(callout 1).
PCA.
1
2




2
1


correct position.

2 1

(callout 3).


1
2
Step 17: Install the integrated scanner assembly (M477 models)

1
2



2
1

2
1
3 4


2

top of the cover.
2
1

1 2 3 4

1
2

2
1
3 4




1 2
3 4
cover.
1
2

1
2

2
1


1
2


front door and duplexer door on page 2542.

2
1


1
2





then close it.

Removal and replacement: Walk-up USB port (M452dw model)
● Introduction
● Step 6: Remove the walk-up USB port (M452dw model)
● Step 8: Install the walk-up USB port (M452dw model)
Introduction
This document provides the procedures to remove and replace the walk-up USB port for the M452.
Before you begin

Walk-up USB port part number
CF368-60001 Walk-up USB port
Required tools





cover (callout 1).
1
2

2
1
2


reengaging.

cover (callout 1).
4 3 2 1

(callout 1).

(callout 1).
wireless PCA.
1
2

2 3 1

(callout 2).

(callout 2).

Step 6: Remove the walk-up USB port (M452dw model)
1. Locate the walk-up USB port.
Figure 1-4852 Locate the walk-up USB port

2. Remove two screws (callout 1), and then disconnect one connector (callout 2).
Figure 1-4853 Remove screws and disconnect connector
3. Remove the walk-up USB port (callout 1).

Step 8: Install the walk-up USB port (M452dw model)

1. Position the slots (callout 1) on the walk-up USB port over the tabs (callout 2) on the printer.

2. Install two screws (callout 1), and then connect one connector (callout 2).
Figure 1-4857 Install screws and connect connector

(callout 2).

(callout 2).

(callout 2).
2 1

(callout 1).

PCA.
1
2
2
1
3 4


2

top of the cover.
2
1

1 2 3 4

1
2

2
1


1
2




then close it.

Removal and replacement: Walk-up USB port (M377, M477 models)
● Introduction
● Step 6: Remove the integrated scanner assembly (M377, M477 models)
● Step 9: Remove the walk-up USB port (M377, M477 models)
● Step 11: Install the walk-up USB port (M377, M477 models)
● Step 14: Install the integrated scanner assembly (M377, M477 models)
Introduction
This document provides the procedures to remove and replace the walk-up USB port for the M377, M477.
Before you begin


Walk-up USB port part number
CF368-60001 Walk-up USB port
Required tools






cover (callout 1).

cover.
1
2





engaging.
cover (callout 1).

4 3
2 1
3
1


2 1
integrated scanner assembly (M377, M477 models) on page 2592.

Step 6: Remove the integrated scanner assembly (M377, M477 models)

(callout 2).
1
2



2
1

2
3
remove it.


(callout 2).
2 1



2
1



Step 9: Remove the walk-up USB port (M377, M477 models)
1. Lay the top cover face-down. Behind the control panel, remove two screws (callout 1).

2. Slide the walk-up USB port (callout 1) out of the sheet metal opening (callout 2).
Figure 1-4944 Slide the walk-up USB port

3. Release the cable (callout 1) from the guides (callout 2), and then disconnect one connector (callout 3).
3 1
Step 11: Install the walk-up USB port (M377, M477 models)
1. Connect one connector (callout 2), and then install the cable (callout 2) in the guides (callout 3).

Figure 1-4947 Connect the walk-up USB port
1 2
2. Install the USB port (callout 1) into the sheet metal opening (callout 2), and then install the slots
(callout 3) on the walk-up USB port over the tabs (callout 4) on the top cover.
1
4





2
1

correct position.


2 1
(callout 3).


1
2

Step 14: Install the integrated scanner assembly (M377, M477 models)
1
2




2
1
cover (M377, M477 models) on page 2624.


2
1
3 4




1 2
3 4
cover.
1
2

1
2

2
1


1
2






then close it.

Removal and replacement: Drawer connector
● Introduction
● Step 5: Remove the drawer connector
● Step 7: Install the drawer connector
Introduction
This document provides the procedures to remove and replace the drawer connector.
Before you begin

Drawer connector part number
VS1-7258-007CN Drawer connector
Required tools






reengaging.
cover (callout 1).

4 3 2 1
Remove the drawer connector on page 2649.


engaging.
cover (callout 1).

4 3
2 1
3
1


2 1
Step 5: Remove the drawer connector
1. Slide the printer slightly over the edge of the work surface in order to access the connector location. On
the left side of the printer, disconnect one connector (callout 1), and then release two tabs (callout 2).
Figure 1-5027 Disconnect one connector and release two tabs

2. Remove the drawer connector.
Figure 1-5028 Remove the drawer connector
Step 7: Install the drawer connector
1. Install the drawer connector through the bottom of the connector holder.

Figure 1-5030 Install the drawer connector
2. Install two tabs (callout 1), and then connect one connector (callout 2).
Figure 1-5031 Install two tabs and connect one connector

2
1
3 4

2

top of the cover.
2
1

1 2 3 4

1
2

2
1
3 4




1 2
3 4
cover.
1
2

1
2



then close it.


Removal and replacement: Accessories
● 550-sheet paper feeder

550-sheet paper feeder
NOTE: HP recommends removing the accessories from the printer before servicing them.
● Removal and replacement: Right cover (550-sheet paper feeder)
● Removal and replacement: Left cover (550-sheet paper feeder)
● Removal and replacement: Rear cover (550-sheet paper feeder)
● Removal and replacement: Switch cable assembly (550-sheet paper feeder)
● Removal and replacement: Lifter drive assembly (550-sheet paper feeder)
● Removal and replacement: Pickup assembly (550-sheet paper feeder)
● Removal and replacement: Front feed guide assembly (550-sheet paper feeder)
● Removal and replacement: Rear feed guide assembly (550-sheet paper feeder)
● Removal and replacement: Paper feed assembly (550-sheet paper feeder)
● Removal and replacement: Pickup motor (550-sheet paper feeder)
● Removal and replacement: Drawer connector (550-sheet paper feeder)
● Removal and replacement: Driver PCA (550-sheet paper feeder)

Removal and replacement: Right cover (550-sheet paper feeder)
● Introduction
● Step 2: Remove the right cover (550-sheet paper feeder)
● Step 4: Install the right cover (550-sheet paper feeder)
Introduction
This document provides the procedures to remove and replace the right cover for the 550-sheet paper feeder.
Before you begin

Right cover part number (550-sheet paper feeder)
RC4-2202-000CN Right cover (550-sheet paper feeder)
Required tools



Step 2: Remove the right cover (550-sheet paper feeder)

2. Release one tab (callout 1) on the top of the feeder, and then release two tabs (callout 2) at the front of
the feeder.
3. Lay the feeder on the left side so that the right side is facing up, and then release one tab (callout 1) on
the bottom of the feeder. Remove the right cover.

Step 4: Install the right cover (550-sheet paper feeder)
1. Lay the feeder on the left side so that the right side is facing up, and then install one tab (callout 1) on
the bottom of the feeder.

2. Turn the feeder to an upright position with the top facing up. Install one tab (callout 1) on the top of the
feeder, and then install two tabs (callout 2) at the front of the feeder.

then close it.


Removal and replacement: Left cover (550-sheet paper feeder)
● Introduction
● Step 2: Remove the left cover (550-sheet paper feeder)
● Step 4: Install the left cover (550-sheet paper feeder)
Introduction
This document provides the procedures to remove and replace the left cover for the 550-sheet paper feeder.
Before you begin

Left cover part number (550-sheet paper feeder)
RC4-2201-000CN Left cover (550-sheet paper feeder)
Required tools



Step 2: Remove the left cover (550-sheet paper feeder)

2. Release one tab (callout 1) on the top of the feeder.
3. Lay the feeder on the right side so that the left side is facing up. Release two tabs (callout 1) on the
bottom of the feeder, and then release two tabs (callout 2) on the front of the feeder.

4. Lift the front of the cover up (callout 1), and then slide the cover (callout 2) toward the back of the feeder
to remove it.
1
2
Step 4: Install the left cover (550-sheet paper feeder)
1. Lay the feeder on the right side so that the left side is facing up. At the back of the feeder, install the
tabs (callout 1) on the cover in the holes (callout 2) on the feeder.

2. Install two tabs (callout 1) on the bottom of the feeder, and then install two tabs (callout 2) on the front
of the feeder.

feeder.

then close it.


Removal and replacement: Rear cover (550-sheet paper feeder)
● Introduction
● Step 4: Remove the rear cover (550-sheet paper feeder)
● Step 6: Install the rear cover (550-sheet paper feeder)
Introduction
This document provides the procedures to remove and replace the rear cover for the 550-sheet paper feeder.
Before you begin

Rear cover part number (550-sheet paper feeder)
RC4-2203-000CN Rear cover (550-sheet paper feeder)
Required tools




the feeder.


to remove it.
1
2
Step 4: Remove the rear cover (550-sheet paper feeder)

2. Rotate the bottom edge of the cover (callout 1) away from the feeder, and then raise the cover up
Figure 1-5085 Remove the rear cover

Step 6: Install the rear cover (550-sheet paper feeder)
1. Install the tabs (callout 1) on the rear cover in the slots (callout 2) on the feeder.
Figure 1-5087 Install the tabs
1
2

2. Make sure that the top of the rear cover (callout 1) is seated in the tabs, and then rotate the bottom of
the cover (callout 2) toward the feeder.

of the feeder.

feeder.



then close it.

Removal and replacement: Switch cable assembly (550-sheet paper feeder)
● Introduction
● Step 5: Remove the PCA cover (550-sheet paper feeder)
● Step 6: Remove the baseplate (550-sheet paper feeder)
● Step 7: Remove the feed frame assembly (550-sheet paper feeder)
● Step 8: Remove the switch cable assembly (550-sheet paper feeder)
● Step 10: Install the switch cable assembly (550-sheet paper feeder)
● Step 11: Install the feed frame assembly (550-sheet paper feeder)
● Step 12: Install the baseplate (550-sheet paper feeder)
● Step 13: Install the PCA cover (550-sheet paper feeder)
Introduction
This document provides the procedures to remove and replace the switch cable assembly for the 550-sheet
feeder.
Before you begin

Switch cable assembly part number
RM2-7897-000CN Switch cable assembly (550-sheet feeder)

Required tools



the feeder.



to remove it.
1
2

Step 5: Remove the PCA cover (550-sheet paper feeder)
1. On the left side of the feeder, remove two screws (callout 1).

2. Remove the PCA cover.
Figure 1-5109 Remove the PCA cover
Step 6: Remove the baseplate (550-sheet paper feeder)
1. Lay the feeder on the top side so that the bottom side is facing up. Remove six screws (callout 1).

2. On the left side of the feeder, release one tab (callout 1) on the foot.
3. Remove the foot.
Figure 1-5112 Remove the foot

5. Rotate the edge of the baseplate up (callout 1), and then lift it up (callout 2) to remove it.
Figure 1-5114 Remove the baseplate
1
2
Step 7: Remove the feed frame assembly (550-sheet paper feeder)
1. Release the cables (callout 1) from the retainers (callout 2).


3. Remove the feed frame assembly.
Figure 1-5117 Remove the feed frame assembly
Step 8: Remove the switch cable assembly (550-sheet paper feeder)
1. Lay the feeder on the right side so that the left side is facing up. Disconnect one connector (callout 1),
and remove the cables from the guides (callout 2). Release two retainers (callout 3), remove the cables
from the retainers, and then thread the connector and cable down through the opening (callout 4) in the
sheet metal.
Figure 1-5118 Disconnect connector and remove five screws
4 2

2. Locate the switch cable assembly (callout 1).
Figure 1-5119 Locate the switch cable assembly
3. Release the cables (callout 1) from the guides (callout 2), and then release two tabs (callout 3).

4. Remove the switch cable assembly and holder (callout 1).
Figure 1-5121 Remove the switch cable assembly and holder
5. Remove the cables (callout 1) on the switch cable assembly from the guides (callout 2) on the switch
holder.
Figure 1-5122 Remove the cables from the guides

7. Remove the switch cable assembly (callout 1) from the switch holder (callout 2).
Figure 1-5124 Remove the switch cable assembly

Step 10: Install the switch cable assembly (550-sheet paper feeder)
1. Position the switch cable assembly into the switch holder so that the hole (callout 1) on the cable
assembly fits over the post (callout 2) on the switch holder. Make sure that two tabs (callout 3) snap into
place.
Figure 1-5126 Position the switch cable assembly

2. Install the cables (callout 1) on the switch cable assembly into the guides (callout 2) on the switch holder.
2
1
3. Install the switch cable assembly on the feeder. Make sure that two tabs (callout 1) snap into the slots
(callout 2), and that the hole (callout 3) on the switch holder fits over the post (callout 4) on the feeder.
Figure 1-5128 Install the switch cable assembly
1
2
4
3

4. Install the cables (callout 1) in the guides (callout 2).
5. Thread the connector and cables up through the opening (callout 1) in the sheet metal. Install the cables
in two retainers (callout 2), and then close the retainers. Install the cables in the guides (callout 3), and
connect one connector (callout 4).
Figure 1-5130 Install the cables and connect one connector
1 3
Step 11: Install the feed frame assembly (550-sheet paper feeder)
1. Install the tabs (callout 1) on the feed frame assembly in the slots (callout 2) on the feeder.

Figure 1-5131 Install the feed frame assembly
2. Install four screws (callout 1).

3. Install the cables (callout 1) in the retainers (callout 2).
Figure 1-5133 Install the cables
Step 12: Install the baseplate (550-sheet paper feeder)
1. Install the tabs (callout 1) on the baseplate into the slots (callout 2) on the feeder.

2. Rotate the edge of the baseplate down.
Figure 1-5135 Rotate the baseplate down
3. Install two tabs (callout 1).

4. Install the foot. Make sure that the tab (callout 1) on the foot fits in the slot (callout 2) on the feeder.
Step 13: Install the PCA cover (550-sheet paper feeder)
1. Install the tabs (callout 1) on the PCA cover in the slots (callout 2) on the feeder.

Figure 1-5139 Install the PCA cover

1
2


of the feeder.
feeder.



then close it.


Removal and replacement: Lifter drive assembly (550-sheet paper feeder)
● Introduction
● Step 8: Remove the lifter drive assembly (550-sheet paper feeder)
● Step 10: Install the lifter drive assembly (550-sheet paper feeder)
● Step14: Install the rear cover (550-sheet paper feeder)
Introduction
This document provides the procedures to remove and replace the lifter drive assembly for the 550-sheet
feeder.
Before you begin

Lifter drive assembly part number
RM2-6493-000CN Lifter drive assembly (550-sheet feeder)

Required tools



the feeder.



to remove it.
1
2



3. Remove the foot.

1
2


Step 8: Remove the lifter drive assembly (550-sheet paper feeder)
1. Lay the feeder on the top so that the bottom is facing up. Disconnect one in-line connector (callout 1).

2. On the right side of the feeder, disconnect one connector (callout 1) from the motor.
3. Release the cables (callout 1) from the retainer (callout 2).

4. Release the cables (callout 1) through the hole in the sheet metal.
5. On the left side of the feeder, remove all of the cables (callout 1) through the opening in the paper
feeder.
Figure 1-5176 Remove the cables

6. Lay the feeder on the right side so that the left side is facing up. Disconnect two connectors (callout 1),
and remove the cables (callout 2) from the guides (callout 3). Remove one screw (callout 4), and then
remove four more screws (callout 5).
Reinstallation tip: One screw (callout 4) is different from the other screws. Make sure that this screw
is installed in the correct position.
4 3
1
5 2
7. Remove the shaft (callout 1).

(callout 3).
1
2
9. Release the tray sensor switch cables (callout 1) through the hole in the sheet metal.
Figure 1-5180 Release the tray sensor switch cables

10. Remove eight screws (callout 1).
Figure 1-5181 Remove eight screws
11. Release four tabs (callout 1), and then remove the cross braces (callout 2).
Figure 1-5182 Remove the cross braces
2 1 2

12. On the left side of the feeder, remove three screws (callout 1), and then release three tabs (callout 2).
Figure 1-5183 Remove screws and release tabs
13. Remove the tray guide (callout 1).
Figure 1-5184 Remove the tray guide

14. Remove the lifter drive assembly (callout 1), and then release the cables (callout 2) through the feeder
frame.
2
1
Step 10: Install the lifter drive assembly (550-sheet paper feeder)

2 1
2. Install the tray guide (callout 1).
Figure 1-5188 Install the tray guide

3. Install three tabs (callout 1), and then install three screws (callout 2).
Figure 1-5189 Install screws and tabs
4. Position the cross braces (callout 1), and then install four tabs(callout 2).
Figure 1-5190 Install the cross braces
1 2 1

5. Install eight screws (callout 1).
Figure 1-5191 Install eight screws
6. Install the tray sensor switch cables (callout 1) through the hole in the sheet metal.
Figure 1-5192 Install the tray sensor switch cables

7. Install the tray sensor switch (callout 1), and then install the cables (callout 2) in the guides (callout 3).
1
2
8. Install the shaft (callout 1) in the hole (callout 2) in the feeder.

9. Connect two connectors (callout 1), and install the cables (callout 2) in the guides (callout 3). Install one
screw (callout 4), and then install four more screws (callout 5).
4 3
1
5 2
10. Turn the printer so that the bottom side is up. On the left side of the feeder, install all of the cables
(callout 1) through the opening in the paper feeder.

11. On the right side of the feeder, install the cables (callout 1) through the hole in the sheet metal.
12. Install the cables (callout 1) in the retainer (callout 2).

13. Connect one connector (callout 1) to the motor.
14. Connect one in-line connector (callout 1).





Step14: Install the rear cover (550-sheet paper feeder)

1
2


of the feeder.
feeder.



then close it.


Removal and replacement: Pickup assembly (550-sheet paper feeder)
● Introduction
● Step 9: Remove the pickup assembly (550-sheet paper feeder)
● Step 11: Install the pickup assembly (550-sheet paper feeder)
Introduction
This document provides the procedures to remove and replace the pickup assembly for the 550-sheet feeder.
Before you begin


Pickup assembly part number
RM2-6490-000CN Pickup assembly (550-sheet feeder)
Required tools



the feeder.



to remove it.
1
2



3. Remove the foot.

1
2




feeder.

4 3
1
5 2

(callout 3).
1
2

2 1 2


frame.
2
1
Step 9: Remove the pickup assembly (550-sheet paper feeder)
1. Lay the feeder on the left side so that the right side is facing up. Remove two screws (callout 1), and
then remove the motor (callout 2).
Figure 1-5256 Remove the motor

2. Remove three screws (callout 1), and then release three tabs (callout 2).

5. Remove the pickup assembly (callout 1).

6. Release the cables (callout 1) through the feeder frame.
Step 11: Install the pickup assembly (550-sheet paper feeder)
1. Lay the feeder on the left side so that the right side is facing up. Install the cables (callout 1) through the
feeder frame.

2. Install the pickup assembly (callout 1).


6. Install the motor (callout 1), and then install two screws (callout 2).
Figure 1-5268 Install the motor

2 1

1 2 1


1
2

4 3
1
5 2








1
2


of the feeder.
feeder.



then close it.


Removal and replacement: Front feed guide assembly (550-sheet paper feeder)
● Introduction
● Step 10: Remove the front feed guide assembly (550-sheet paper feeder)
● Step 12: Install the front feed guide assembly (550-sheet paper feeder)
Introduction
This document provides the procedures to remove and replace the front feed guide assembly for the 550-
sheet feeder.
Before you begin


Front feed guide assembly part number
RM2-6492-000CN Front feed guide assembly (550-sheet feeder)
Required tools



the feeder.



to remove it.
1
2



3. Remove the foot.

1
2




feeder.

4 3
1
5 2

(callout 3).
1
2

2 1 2


frame.
2
1



Step 10: Remove the front feed guide assembly (550-sheet paper feeder)
and then remove the cables (callout 2) from the guides (callout 3).
3
2

2. Press the lever (callout 1) on the roller holder, and then slide the roller holder down (callout 2).
1
2

2 1

6. Release the cables (callout 1) through the feeder frame (callout 2), and then remove the front feed guide
2
1
Step 12: Install the front feed guide assembly (550-sheet paper feeder)
1. Install the front feed guide (callout 1), and then install the cables (callout 2), through the feeder frame
(callout 3).

3
2
2. Install the roller holder (callout 1).

2 1
4. Install the pickup and feed roller case (callout 1) on the shafts (callout 2).
Figure 1-5354 Install the pickup and feed rollers
2
1

5. Slide the roller holder up until it snaps into place.
3
2
feeder frame.




2 1

1 2 1


1
2

4 3
1
5 2








1
2


of the feeder.
feeder.



then close it.


Removal and replacement: Rear feed guide assembly (550-sheet paper feeder)
● Introduction
● Step 11: Remove the rear feed guide assembly (550-sheet paper feeder)
● Step 13: Install the rear feed guide assembly (550-sheet paper feeder)
Introduction
This document provides the procedures to remove and replace the rear feed guide assembly on the 550-sheet
feeder.

Before you begin
Rear feed guide assembly part number
RM2-6366-000CN Rear feed guide assembly (550-sheet feeder)
Required tools



the feeder.



to remove it.
1
2



3. Remove the foot.

1
2




feeder.

4 3
1
5 2

(callout 3).
1
2

2 1 2


frame.
2
1



3
2

1
2

2 1

2
1
Step 11: Remove the rear feed guide assembly (550-sheet paper feeder)

Step 13: Install the rear feed guide assembly (550-sheet paper feeder)
▲ Install the rear feed guide assembly. Make sure that the tabs are installed securely (callout 1).
(callout 3).

3
2

2 1
2
1

3
2
feeder frame.




2 1

1 2 1


1
2

4 3
1
5 2








1
2


of the feeder.
feeder.



then close it.


Removal and replacement: Paper feed assembly (550-sheet paper feeder)
● Introduction
● Step 11: Remove the rear feed guide assembly (550-sheet paper feeder)
● Step 12: Remove the paper feed assembly (550-sheet paper feeder)
● Step 14: Install the paper feed assembly (550-sheet paper feeder)
● Step 13: Install the rear feed guide assembly (550-sheet paper feeder)
Introduction
This document provides the procedures to remove and replace the paper feed assembly on the 550-sheet
feeder.

Before you begin
Paper feed assembly part number
RM2-6494-000CN Paper feed assembly (550-sheet feeder)
Required tools



the feeder.



to remove it.
1
2



3. Remove the foot.

1
2




feeder.

4 3
1
5 2

(callout 3).
1
2

2 1 2


frame.
2
1



3
2

1
2

2 1

2
1
Step 11: Remove the rear feed guide assembly (550-sheet paper feeder)
Step 12: Remove the paper feed assembly (550-sheet paper feeder)
1. On the left side of the feeder, disconnect one connector (callout 1).

2. On the top of the feeder toward the back, remove three screws (callout 1).

3. Remove the front paper feed guide (callout 1).
Figure 1-5543 Remove the front paper feed guide
4. Inside the paper feeder toward the back, remove two screws (callout 1).

5. Release the cables (callout 1) through the opening (callout 2) in the feeder, and then remove the paper
feed assembly (callout 3).
Figure 1-5545 Remove the paper feed assembly
3
1 2
Step 14: Install the paper feed assembly (550-sheet paper feeder)
1. Position the paper feed assembly (callout 1) in the feeder. Install the cables (callout 2) through the
opening (callout 3) in the feeder.

Figure 1-5547 Install the paper feed assembly
1
2 3
2. When installing the paper feed assembly, make sure that five tabs (callout 1) are installed correctly.

4. On the top of the feeder toward the back, install the front paper feed guide (callout 1).
Figure 1-5550 Install the front paper feed guide

6. On the left side of the feeder, connect one connector (callout 1).
Step 13: Install the rear feed guide assembly (550-sheet paper feeder)
▲ Install the rear feed guide assembly. Make sure that the tabs are installed securely (callout 1).

(callout 3).
3
2

2 1

2
1

3
2
feeder frame.



2 1


1 2 1

1
2

4 3
1
5 2








1
2


of the feeder.

feeder.



then close it.

Removal and replacement: Pickup motor (550-sheet paper feeder)
● Introduction
● Step 3: Remove the pickup motor (550-sheet paper feeder)
● Step 5: Install the pickup motor (550-sheet paper feeder)
Introduction
This document provides the procedures to remove and replace the pickup motor on the 550-sheet feeder.
Before you begin

Pickup motor part number
RM2-7350-000CN Pickup motor (550-sheet feeder)
Required tools





to remove it.
1
2
Step 3: Remove the pickup motor (550-sheet paper feeder)

▲ Disconnect one connector (callout 1), remove two screws (callout 2), and then remove the pickup motor
(callout 3).
2
1

Step 5: Install the pickup motor (550-sheet paper feeder)

▲ Install the pickup motor (callout 1), install two screws (callout 2), and then connect one connector
(callout 3).
2
3

of the feeder.

feeder.

then close it.


Removal and replacement: Drawer connector (550-sheet paper feeder)
● Introduction
● Step 3: Remove the drawer connector (550-sheet paper feeder)
● Step 5: Install the drawer connector (550-sheet paper feeder)
● Step 6: Install the right cover (550-sheet feeder)
Introduction
This document provides the procedures to remove and replace the drawer connector on the 550-sheet feeder.
Before you begin

Drawer connector part number
VS1-7257-007CN Drawer connector (550-sheet feeder)
Required tools




the feeder.
Step 3: Remove the drawer connector (550-sheet paper feeder)
1. On the left side of the feeder, disconnect one connector (callout 1).


3. Lift the connector holder off of the feeder, and then release two tabs (callout 1) to release the connector
from the holder.
4. Remove the cables (callout 1) through the opening in the connector holder (callout 2).

5. Disconnect the wire harness (callout 1) from the connector (callout 2). Set the wire harness aside to be
installed on the replacement part.
Figure 1-5622 Disconnect the wire harness
2 1
Step 5: Install the drawer connector (550-sheet paper feeder)
1. Connect the wire harness (callout 1) to the replacement connector (callout 2).

Figure 1-5624 Connect the wire harness
2 1
2. Install the cables (callout 1) through the opening in the connector holder (callout 2), and then snap the
connector into place.

3. Make sure that the two tabs (callout 1) are full installed in the connector holder.
4. Install the hole (callout 1) in the connector holder over the post (callout 2) on the feeder.
Figure 1-5627 Install the connector holder

Step 6: Install the right cover (550-sheet feeder)



then close it.

Removal and replacement: Driver PCA (550-sheet paper feeder)
● Introduction
● Step 2: Remove the right cover (550-sheet feeder)
● Step 3: Remove the PCA cover (550-sheet feeder)
● Step 4: Remove the driver PCA (550-sheet paper feeder)
● Step 6: Install the driver PCA (550-sheet paper feeder)
● Step 7: Install the PCA cover (550-sheet feeder)
● Step 8: Install the right cover (550-sheet feeder)
Introduction
This document provides the procedures to remove and replace the driver PCA on the 550-sheet feeder.
Before you begin

Driver PCA part number
RM2-7366-000CN Driver PCA (550-sheet feeder)
Required tools



Step 2: Remove the right cover (550-sheet feeder)

the feeder.
Step 3: Remove the PCA cover (550-sheet feeder)

Step 4: Remove the driver PCA (550-sheet paper feeder)
1. Disconnect all of the connectors on the driver PCA (callout 1).


3. Lift the driver PCA up and off of two brackets (callout 1) to remove it.
Step 6: Install the driver PCA (550-sheet paper feeder)
1. Position the driver PCA on two brackets (callout 1).

Figure 1-5644 Position the driver PCA

3. Connect all of the connectors on the driver PCA (callout 1).
Step 7: Install the PCA cover (550-sheet feeder)

Step 8: Install the right cover (550-sheet feeder)


then close it.


2 Parts and diagrams
● For additional service and support
● Assembly locations
● Order parts, accessories, and supplies
● How to use the parts lists and diagrams
● Parts and diagrams: Document feeder and scanner whole units
● Parts and diagrams: Covers and control panels
● Parts and diagrams: Internal components
● Parts and diagrams: 550-sheet paper feeder
● Alphabetical parts list
● Numerical parts list
ENWW 2985
For additional service and support
home.do.

2986 Chapter 2 Parts and diagrams ENWW

Assembly locations
● Base printer, M452
● Base printer, M377 and M477
● 550-sheet paper feeder (all models)
Base printer, M452

Figure 2-1 Base printer, M452
12 1 2 3 4
11
10
9
8
7
5
6
1 2-line control panel (nw and dn models) 7 Tray 1
2 Near field communication (NFC) internal antenna (dw 8 Power on/off button
model only)
3 Walk-up USB port (for printing without a computer) (dw 9 Front door (provides toner cartridge access)
model only)
4 Touchscreen control panel (dw model) (tilts up for 10 Output bin extension
easier viewing)
5 Regulatory label (inside the front door) 11 Front door open button (on left cover)
6 Tray 2 12 Output bin
ENWW Assembly locations 2987

Base printer, M377 and M477
Figure 2-2 Base printer, M377 and M477
2
1
12
11
10
3
9
8
7
6
5 4
1 Scanner 7 Front door (provides toner cartridge access)
2 Document feeder 8 Output bin extension
3 Regulatory label (inside the front door) 9 Output bin
4 Tray 2 10 Front door open button (on left cover)
5 Tray 1 11 Walk-up USB port (for printing and scanning without a

computer)
6 Power on/off button 12 Touchscreen control panel (tilts up for easier viewing)

550-sheet paper feeder (all models)
Figure 2-3 550-sheet paper feeder (all models)
1
3
1 Positioning pins
2 Tray 3
3 Connector
ENWW Assembly locations 2989

Order parts, accessories, and supplies
Ordering
Order supplies and paper www.hp.com/go/suresupply
Order genuine HP parts or accessories www.hp.com/buy/parts
or
partsurfer.hp.com
Order through service or support providers Contact an HP-authorized service or support provider.
Order using the HP Embedded Web Server (EWS) To access, in a supported Web browser on your computer, enter the printer IP
address or host name in the address/URL field. The EWS contains a link to the HP
SureSupply Web site, which provides options for purchasing Original HP supplies.
Orderable parts
Not all of the parts shown in the diagrams in this chapter can be ordered. Refer to the table following the
diagram or the parts lists at the end of this chapter to determine if a part is orderable.
Supplies
Following are the part numbers for the supplies available for the printer (all models).
Table 2-4 Supplies

Item Description Part number
HP 410A Black Original LaserJet Toner Cartridge Standard-capacity replacement black toner CF410A (new)
cartridge (410A)
CF410-67901 (service)
HP 410X High Yield Black Original LaserJet Toner High-capacity replacement black toner CF410X (new)
Cartridge cartridge (410X)
HP 410A Cyan Original LaserJet Toner Cartridge Standard-capacity replacement cyan CF411A (new)
cartridge (410A)
HP 410X High Yield Cyan Original LaserJet Toner High-capacity replacement cyan toner CF411X (new)
HP 410A Yellow Original LaserJet Toner Cartridge Standard-capacity replacement yellow toner CF412A (new)
cartridge (410A)
HP 410X High Yield Yellow Original LaserJet Toner High-capacity replacement yellow toner CF412X (new)

Table 2-4 Supplies (continued)
HP 410A Magenta Original LaserJet Toner Cartridge Standard-capacity replacement magenta CF413A (new)
toner cartridge (410A)
HP 410X High Yield Magenta Original LaserJet Toner High-capacity replacement magenta toner CF413X (new)
Accessories
Following are the part numbers for the accessories available for the printer (all models).
Table 2-5 Accessories
550-sheet paper feeder Optional 550-sheet paper feeder CF404A (new)
USB 2.0 printer cable A-to-B cable (2-meter standard) C6518A (new)
8121-0868 (service)
Customer self-repair kits

Following are the customer-replaceable kits available for the printer. Each kit includes parts and installation
instructions.
The customer self-repair (CSR) level indicates the expected difficulty the customer will experience when
replacing this part:
● A: Easy
● B: Difficult
Item Description CSR level Part number
550-sheet paper Replacement optional Tray 3 A CF404-67902

feeder
Related documentation and software

home.do.
ENWW Order parts, accessories, and supplies 2991

How to use the parts lists and diagrams
The figures in this chapter show the major subassemblies in the printer and their component parts. A parts
list table follows each exploded view assembly diagram. Each table lists the item number, the associated part
number, and the description of each part. If a part is not listed in the table, then it is not a field replacement
unit (FRU).
CAUTION: Be sure to order the correct part. When looking for part numbers for electrical components, pay
careful attention to the voltage that is listed in the description column. Doing so will ensure that the part
number selected is for the correct model.
NOTE: In this manual, the abbreviation “PCA” stands for “printed circuit-board assembly.” Components
described as a PCA might consist of a single circuit board or a circuit board plus other parts, such as cables
and sensors.

ENWW How to use the parts lists and diagrams 2993
Parts and diagrams: Document feeder and scanner whole units
NOTE: M377, M477 models only.
Document feeder and scanner (M377, M477)

Figure 2-4 Document feeder and scanner (M377, M477)
1

Table 2-6 Document feeder and scanner (M377, M477)
Ref Description Part number Qty
1 Integrated scanner assembly (M477) CF377-60104 1
1 Integrated scanner assembly (M377) CF377-60124 1
Not shown Integrated scanner assembly lift assembly (M377, M477) B3Q10-60128 1
Not shown Slider pin, integrated scanner assembly lift (M377, M477) B3Q10-40041 1
Not shown Spring, separator pad (M377, M477) B3Q10-00019 1
Not shown Support, separator pad (M377, M477) B3Q10-40079 1
Not shown Separator pad (M377, M477) B3Q10-40080 1
Not shown Cover, document feeder outer (M377, M477) B3Q10-40013 1
Not shown Document feeder pick assembly (M377, M477) B3Q10-60105 1
Not shown Shaft, document feeder pick extension (M377, M477) B3Q10-40081 1
Not shown Bearing extension (M377, M477) B3Q10-40074 1
Not shown Document feeder input tray assembly (M377, M477) B3Q10-60107 1
ENWW Parts and diagrams: Document feeder and scanner whole units 2995
Parts and diagrams: Covers and control panels
M452 covers and control panels
Figure 2-5 M452 covers and control panels
Simplex wireless model / Duplex network model Duplex wireless model
9 10
A06 A06
A06 A06
Duplex model Simplex model
A04
1
4
A05
A05 5
A06
A06
A06
A04 A03
A02
A01

Table 2-7 M452 covers and control panels
1 Cover, right (M452) RC4-4853-000CN 1
2 Cover, left (M452) RC4-4854-000CN 1
3 Cover, rear (simplex models) RC4-4855-000CN 1
4 Door, rear (simplex models) RC4-5130-000CN 1
5 Cover, rear lower (simplex models) RC4-5131-000CN 1
6 Cover, cassette RC4-5334-000CN 1
7 Duplexing door assembly (duplex models) RM2-6383-000CN 1
8 Door, front assembly RM2-6390-000CN 1
9 Cover, top and control panel (M452nw) RM2-6433-000CN 1
9 Cover, top and control panel (M452dn) RM2-6442-000CN 1
10 Cover, top (M452dw) RM2-6456-000CN 1
Not shown Control panel, touchscreen (M452dw) CF388-60113 1
ENWW Parts and diagrams: Covers and control panels 2997

M377, M477 covers and control panel
Figure 2-6 M377, M477 covers and control panel
A05 A05 A05
A05
9
A06
A04
A07
Dupex models Simplex models

A07
3
1
A05
A06
A06 5
2 A07
A07
A07
A05 A03
A02
A01

Table 2-8 M377, M477 covers and control panel
1 Cover, right (M377, M477) RC4-6044-000CN 1
2 Cover, left (M377, M477) RC4-6045-000CN 1
3 Cover, rear (simplex models) RC4-4855-000CN 1
4 Door, rear (simplex models) RC4-5130-000CN 1
5 Cover, rear lower (simplex models) RC4-5131-000CN 1
6 Cover, cassette RC4-5334-000CN 1
7 Duplexing door assembly (duplex models) RM2-6383-000CN 1
8 Door, front assembly RM2-6390-000CN 1
9 Cover, top (M377, M477fdw) RM2-6468-000CN 1
9 Cover, top (M477fnw/fdn) RM2-6466-000CN 1
Not shown Control panel, touchscreen (M377, M477) B5L25-60101 1
Not shown Cover, 4.3” control panel back (M377, M477) CF377-40003 1
Not shown Assembly, control panel mount chassis 4.3 (M377, M477) CF377-60113 1
Not shown Control panel mount chassis 4.3 (M377, M477) B3Q10-40055 1
Not shown Gear, control panel friction (M377, M477) B3Q09-40003 1
Not shown FFC cover (M377, M477) CF377-40004 1
Not shown Fax cover (M477) CF377-40005 1
Not shown Fax cable cover (M477) CF377-40006 1
Not shown Shield, RFI SSA FFC (M377, M477) CF377-00006 1
ENWW Parts and diagrams: Covers and control panels 2999

Parts and diagrams: Internal components
Internal components (1 of 5)
Figure 2-7 Internal components (1 of 5)
A39
(J3100)
A29 6
A01
(J120) 4
A01
A36
A24
A36
(J801)
(J802) A18
(J110) (J111) A01
A25 A26 2 (J123)

A20
A19
12 3
A11
A37 A17
1
A36
A21 A16
A38
10 A05 M452 wireless model
11
(FM2)
A03 (J206)
(SW601)
(J3040) (J623)
A33
(J2100)
A32 5
A02 A36
A37 A15
(J903)
A23 A06
(J132)
A36
A28 A22
M452 A35 A02
(J901) A37
A14
A12
A27
(J100) A37 A35 A13
A07
A37 A08
A37 9 A30
(J122) See Internal
A04 A37
components (3 of 5) (SW1) 7
Z (J117)
(J1001)
A39 A09
(J3040) A37
(J2100)
A31 A39
(SW6) A37
(J1001)
(J106) A10
A34
(J144)
8

Table 2-9 Internal components (1 of 5)
1 Fan (FM2) RK2-6270-000CN 1
2 Cable, flexible flat RK2-6300-000CN 1
4 Laser/scanner assembly RM2-5612-000CN 1
5 Switch assembly, power RM2-6373-000CN 1
6 Memory PCA RM2-7374-000CN 1
7 Switch, cable front door assembly RM2-7889-000CN 1
8 Switch, cassette cable assembly RM2-7896-000CN 1
9 Engine controller PCA (duplex models) RM2-7909-000CN 1
9 Engine controller PCA (simplex models) RM2-7910-000CN 1
10 Formatter PCA, generic (M452nw/dn) CF389-60001 1
10 Formatter PCA, generic (M452dw) CF394-60001 1
10 Formatter PCA (M452nw) CF388-60003 1
10 Formatter PCA (M452nw—China only) CF388-67018 1
10 Formatter PCA (M452dn) CF389-60002 1
10 Formatter PCA (M452dn—China only) CF389-67018 1
10 Formatter PCA (M452dw) CF394-60002 1
10 Formatter PCA (M452dw—China only) CF394-67018 1
10 Formatter PCA, generic (M477) CF379-60001 1
10 Formatter PCA (M477fnw) CF377-60001 1
10 Formatter PCA (M477fnw—China only) CF377-67018 1
10 Formatter PCA (M477fdn) CF378-60002 1
10 Formatter PCA (M477fdn—China only) CF378-67018 1
10 Formatter PCA (M477fdw) CF379-60003 1
10 Formatter PCA (M477fdw—China only) CF379-67018 1
10 Formatter PCA (M377dw) CF378-67902 1
10 Formatter PCA (M377dw-China only) CF378-67901 1
11 Wireless PCA (M452nw/dw) 0960-3295 1
11 Wireless PCA (M377, M477fnw/fdw) 1150-7967 1
12 Fax PCA (M477; US) CF206-60001 1
12 Fax PCA (M477; Europe) CF207-60001 1
12 Fax PCA (M477; Brazil) CF208-60001 1
A34 Connector, drawer VS1-7258-007CN 1
ENWW Parts and diagrams: Internal components 3001

(J201)
M452 (J321) A19

A23
(J113)
A03
(J451)
A23
(J453)
(J452)
(J104)
A23 (J105)
(J109)
A01 (J116) (J623)
A02
A20
A (J119)
A11
M477
A23 3
A23 A23 A23
A23
A23
A14
A22 A21
A17
4
A21 A23
A16
A15
A18 A12
A23
A13
A23 A01 5 A23
A A23 A23
(J210)
M452
Duplex wireless model
A A24 A10 A24
A04
A07
A05 A23
A06
(FM1)
A05 A23 (J205)
A09
A08
A22

1 Fan (FM1) RK2-6270-000CN 1
3 Fuser power supply PCA (110-127V) RM2-6440-000CN 1
3 Fuser power supply PCA (220-240V) RM2-6441-000CN 1
4 Driver PCA RM2-7369-000CN 1
5 Low-voltage power supply (110-127V) RM2-7913-000CN 1
5 Low-voltage power supply (220-240V) RM2-7914-000CN 1
Not shown Remote antenna (M452nw/dw) 0960-3467 1
Not shown Wireless bracket (M377, M477fnw/fdw) CF377-40007 1
Not shown Wireless cable (M377, M477fnw/fdw) CF377-60115 1
Not shown Cable, fax (M477) CF377-60105 1
Not shown Cable, FFC (M377, M477) CF388-60116 1

A31 A24
A03
7 (J204)
(J2004)
(J212)
A29 A22
(M4) (J2002)
(J2004)
A31 A23
(M2)
6 A31 (J203)
(J2002)
5 (J2003)
(M3)
(J2003)
(J3040)
(J2100)
9
4
A26
A06
A07 A08
See Internal
components A05
(1 of 5)
Z A01 B A09
A
A04 A14
A27 (SR6)
A02 (J3006)
A30 A12 (J114)
A30 (J3006)
A11 10
A21
A25
A15
A10
A18 A
A16
A10 B
A17
1
3
(J121) A28
A19
(J3050)
A20
8 A13 A32

1 Roller, paper pickup RL1-2593-000CN 1
2 Cassette (Tray 2) assembly RM2-6377-000CN 1
3 Pad, separation RM2-6406-000CN 1
4 Intermediate transfer belt (ITB) RM2-6454-000CN 1
5 Motor, drum (M2) RM2-7342-000CN 1
6 Motor, developing (M3) RM2-7344-000CN 1
7 Motor, fuser (M4) RM2-7348-000CN 1
8 Sensor, environment PCA RM2-7376-000CN 1
9 Sensor, density detect RM2-7399-000CN 1
10 Photointerrupter WG8-5935-000CN 1

A31 A27
10
A07
(J202)
(M1)
(J2001)
A05 (J2001)
A32
A04
9
A03
A30
A25
A31
A32 A12
A06 A01
A
A06 A01
A09
A31
A23
A02
A10
8 A08
A29
(J144)
A31 A22
5
(J103)
4 A31
A21
2 A11
1 A32 A28
A11
A24
7
A20
A11 A
A28
A14 3 A24
A26 A19
A20
A13
A15
(J140)
6
A32 A18 A17
A16

1 Roller, paper pickup assembly RM2-5576-000CN 1
2 Roller, feed assembly RM2-5577-000CN 1
3 Roller, separation RM2-5881-000CN 1
4 Feed guide assembly, rear RM2-6366-000CN 1
5 Feed guide assembly, front RM2-6368-000CN 1
6 Lifter drive assembly RM2-6370-000CN 1
7 Paper pickup assembly RM2-6372-000CN 1
8 Registration assembly RM2-6374-000CN 1
9 Cartridge tray assembly RM2-6401-000CN 1
10 Motor, pickup (M1) RM2-7350-000CN 1

Simplex model
5
A15
(J311)
A15 (J322)
A15
B
A15
(J108)
(J112)
(J124)
A
(J107)
(J125)
(J126)
Duplex model
5
A15
(J311)
A15 (J322)
A15 B
A15
(J129)
(J127)
(J108)
A
(J112)
(J124)
(J107) A13 A08
(J125)
(J126)
A07
B 2 A05
A10 A06
A09
3
A12
4 A02
A11 A
A04
A01
(J134)
(J128)
1 A16
A15 A14
A03
A01

1 Paper pickup assembly (duplex models) RM2-6387-000CN 1
2 Reverse drive assembly (duplex models) RM2-6389-000CN 1
3 Secondary transfer assembly (duplex models) RM2-6397-000CN 1
3 Secondary transfer assembly (simplex models) RM2-6430-000CN 1
4 Secondary transfer roller RM2-6455-000CN 1
5 Fuser (duplex; 110-127V) RM2-6418-000CN 1
5 Fuser (duplex; 220-240V) RM2-6435-000CN 1
5 Fuser (simplex; 110-127V) RM2-6431-000CN 1
5 Fuser (simplex; 220-240V) RM2-6436-000CN 1
Not shown Walk-up USB port CF368-60001
Not shown Near-field communication (NFC) PCA (M452dw/M477fdw) B4K93-60001

Parts and diagrams: 550-sheet paper feeder
550-sheet paper feeder covers
Figure 2-12 550-sheet paper feeder covers
A01
A01
1
A01
3
A01
A01
A01
2
4

Table 2-14 550-sheet paper feeder covers
1 Cover, left (550-sheet feeder) RC4-2201-000CN 1
2 Cover, right (550-sheet feeder) RC4-2202-000CN 1
3 Cover, rear (550-sheet feeder) RC4-2203-000CN 1
4 Cover, cassette (550-sheet feeder) RC4-2224-000CN 1
ENWW Parts and diagrams: 550-sheet paper feeder 3011

550-sheet paper feeder main body (1 of 2)
Figure 2-13 550-sheet paper feeder main body (1 of 2)
A33 (J1001)
(J750) A36 A11

A27
A36
A02
A36
A36 A14 A30

A30 A36
A14
A14
A30
A30
A36
A30
A30 A07
A36
A07
A34
A34
A09
A07
A36
11
A35
A36
A13
A36 A36 A18
A01
A17 A34
A12
A36
A26
A36
A04
A36
A04

Table 2-15 550-sheet paper feeder main body (1 of 2)
11 Paper feeder driver PCA (550-sheet feeder) RM2-7366-000CN 1
A33 Connector, drawer (550-sheet feeder) VS1-7257-007CN 1

550-sheet paper feeder main body (2 of 2)
Figure 2-14 550-sheet paper feeder main body (2 of 2)
A36 A03 A37
10
A10 A36
(M9)
(J2009)
A08
A34
A38
A38
A38
A15
A24
A37 A15
A A06
A38
A01
A16
9
A05
A31
A36 (J756) 7
A37 5
4
(J755)
2 1
A38
A28
6 (J777)
A19
A25 A32
3 A (J2009)
(J754)
A20
A29
(SW31) (J752)
(J753)
A23 A22
8
A38 (J757) A21
12

Table 2-16 550-sheet paper feeder main body (2 of 2)
1 Paper pickup roller assembly (550-sheet feeder) RM2-5576-000CN 1
2 Feed roller assembly (550-sheet feeder) RM2-5577-000CN 1
3 Separation roller assembly (550-sheet feeder) RM2-5881-000CN 1
4 Feed guide assembly, rear (550-sheet feeder) RM2-6366-000CN 1
5 Cassette assembly (550-sheet feeder) RM2-6486-000CN 1
6 Paper pickup assembly (550-sheet feeder) RM2-6490-000CN 1
7 Feed guide assembly, front (550-sheet feeder) RM2-6492-000CN 1
8 Lifter drive assembly (550-sheet feeder) RM2-6493-000CN 1
9 Paper feed assembly (550-sheet feeder) RM2-6494-000CN 1
10 Pickup motor (M9) (550-sheet feeder) RM2-7350-000CN 1
12 Switch cable assembly (550-sheet feeder) RM2-7897-000CN 1

Alphabetical parts list
Table 2-17 Alphabetical parts list
Description Part number Table and page
Assembly, control panel mount chassis 4.3 (M377, M477) CF377-60113 M377, M477 covers and control
panel on page 2999
Bearing extension (M377, M477) B3Q10-40074 Document feeder and scanner

(M377, M477) on page 2995
Cable, fax (M477) CF377-60105 Internal components (2 of 5)

on page 3003
Cable, FFC (M377, M477) CF388-60116 Internal components (2 of 5)

on page 3003
Cable, flexible flat RK2-6300-000CN Internal components (1 of 5)

on page 3001

on page 3001

on page 3003
Cartridge tray assembly RM2-6401-000CN Internal components (4 of 5)

on page 3007
Cassette (Tray 2) assembly RM2-6377-000CN Internal components (3 of 5)

on page 3005
Cassette assembly (550-sheet feeder) RM2-6486-000CN 550-sheet paper feeder main

body (2 of 2) on page 3015
Connector, drawer (550-sheet feeder) VS1-7257-007CN 550-sheet paper feeder main

Connector, drawer VS1-7258-007CN Internal components (1 of 5)

on page 3001
Control panel mount chassis 4.3 (M377, M477) B3Q10-40055 M377, M477 covers and control
panel on page 2999
Control panel, touchscreen (M377, M477) B5L25-60101 M377, M477 covers and control
panel on page 2999
Control panel, touchscreen (M452dw) CF388-60113 M452 covers and control panels
on page 2997
Cover, 4.3” control panel back (M377, M477) CF377-40003 M377, M477 covers and control
panel on page 2999
Cover, cassette (550-sheet feeder) RC4-2224-000CN 550-sheet paper feeder covers

on page 3011
Cover, cassette RC4-5334-000CN M452 covers and control panels

on page 2997
Cover, cassette RC4-5334-000CN M377, M477 covers and control

panel on page 2999
Cover, document feeder outer (M377, M477) B3Q10-40013 Document feeder and scanner
(M377, M477) on page 2995

Table 2-17 Alphabetical parts list (continued)
Cover, left (550-sheet feeder) RC4-2201-000CN 550-sheet paper feeder covers

on page 3011
Cover, left (M377, M477) RC4-6045-000CN M377, M477 covers and control
panel on page 2999
Cover, left (M452) RC4-4854-000CN M452 covers and control panels

on page 2997
Cover, rear (550-sheet feeder) RC4-2203-000CN 550-sheet paper feeder covers

on page 3011
Cover, rear (simplex models) RC4-4855-000CN M452 covers and control panels
on page 2997
Cover, rear (simplex models) RC4-4855-000CN M377, M477 covers and control
panel on page 2999
Cover, rear lower (simplex models) RC4-5131-000CN M452 covers and control panels
on page 2997
Cover, rear lower (simplex models) RC4-5131-000CN M377, M477 covers and control
panel on page 2999
Cover, right (550-sheet feeder) RC4-2202-000CN 550-sheet paper feeder covers

on page 3011
Cover, right (M377, M477) RC4-6044-000CN M377, M477 covers and control
panel on page 2999
Cover, right (M452) RC4-4853-000CN M452 covers and control panels

on page 2997
Cover, top (M377, M477fdw) RM2-6468-000CN M377, M477 covers and control
panel on page 2999
Cover, top (M452dw) RM2-6456-000CN M452 covers and control panels

on page 2997
Cover, top (M477fnw/fdn) RM2-6466-000CN M377, M477 covers and control

panel on page 2999
Cover, top and control panel (M452dn) RM2-6442-000CN M452 covers and control panels
on page 2997
Cover, top and control panel (M452nw) RM2-6433-000CN M452 covers and control panels
on page 2997
Document feeder input tray assembly (M377, M477) B3Q10-60107 Document feeder and scanner
(M377, M477) on page 2995
Document feeder pick assembly (M377, M477) B3Q10-60105 Document feeder and scanner
(M377, M477) on page 2995
Door, front assembly RM2-6390-000CN M452 covers and control panels

on page 2997
Door, front assembly RM2-6390-000CN M377, M477 covers and control

panel on page 2999
Door, rear (simplex models) RC4-5130-000CN M452 covers and control panels
on page 2997
ENWW Alphabetical parts list 3017

Door, rear (simplex models) RC4-5130-000CN M377, M477 covers and control
panel on page 2999
Driver PCA RM2-7369-000CN Internal components (2 of 5)

on page 3003
Duplexing door assembly (duplex models) RM2-6383-000CN M452 covers and control panels
on page 2997
Duplexing door assembly (duplex models) RM2-6383-000CN M377, M477 covers and control
panel on page 2999
Engine controller PCA (duplex models) RM2-7909-000CN Internal components (1 of 5)

on page 3001
Engine controller PCA (simplex models) RM2-7910-000CN Internal components (1 of 5)

on page 3001
Fan (FM1) RK2-6270-000CN Internal components (2 of 5)

on page 3003
Fan (FM2) RK2-6270-000CN Internal components (1 of 5)

on page 3001
Fax cable cover (M477) CF377-40006 M377, M477 covers and control
panel on page 2999
Fax cover (M477) CF377-40005 M377, M477 covers and control

panel on page 2999
Fax PCA (M477; Brazil) CF208-60001 Internal components (1 of 5)

on page 3001
Fax PCA (M477; Europe) CF207-60001 Internal components (1 of 5)

on page 3001
Fax PCA (M477; US) CF206-60001 Internal components (1 of 5)

on page 3001
Feed guide assembly, front (550-sheet feeder) RM2-6492-000CN 550-sheet paper feeder main
Feed guide assembly, front RM2-6368-000CN Internal components (4 of 5)

on page 3007
Feed guide assembly, rear (550-sheet feeder) RM2-6366-000CN 550-sheet paper feeder main
Feed guide assembly, rear RM2-6366-000CN Internal components (4 of 5)

on page 3007
Feed roller assembly (550-sheet feeder) RM2-5577-000CN 550-sheet paper feeder main
FFC cover (M377, M477) CF377-40004 M377, M477 covers and control
panel on page 2999
Formatter PCA (M377dw) CF378-67902 Internal components (1 of 5)

on page 3001
Formatter PCA (M377dw-China only) CF378-67901 Internal components (1 of 5)

on page 3001

Formatter PCA (M452dn) CF389-60002 Internal components (1 of 5)

on page 3001
Formatter PCA (M452dn—China only) CF389-67018 Internal components (1 of 5)

on page 3001
Formatter PCA (M452dw) CF394-60002 Internal components (1 of 5)

on page 3001
Formatter PCA (M452dw—China only) CF394-67018 Internal components (1 of 5)

on page 3001
Formatter PCA (M452nw) CF388-60003 Internal components (1 of 5)

on page 3001
Formatter PCA (M452nw—China only) CF388-67018 Internal components (1 of 5)

on page 3001
Formatter PCA (M477fdn) CF378-60002 Internal components (1 of 5)

on page 3001
Formatter PCA (M477fdn—China only) CF378-67018 Internal components (1 of 5)

on page 3001
Formatter PCA (M477fdw) CF379-60003 Internal components (1 of 5)

on page 3001
Formatter PCA (M477fdw—China only) CF379-67018 Internal components (1 of 5)

on page 3001
Formatter PCA (M477fnw) CF377-60001 Internal components (1 of 5)

on page 3001
Formatter PCA (M477fnw—China only) CF377-67018 Internal components (1 of 5)

on page 3001
Formatter PCA, generic (M452dw) CF394-60001 Internal components (1 of 5)

on page 3001
Formatter PCA, generic (M452nw/dn) CF389-60001 Internal components (1 of 5)

on page 3001
Formatter PCA, generic (M477) CF379-60001 Internal components (1 of 5)

on page 3001
Fuser (duplex; 110-127V) RM2-6418-000CN Internal components (5 of 5)

on page 3009
Fuser (duplex; 220-240V) RM2-6435-000CN Internal components (5 of 5)

on page 3009
Fuser (simplex; 110-127V) RM2-6431-000CN Internal components (5 of 5)

on page 3009
Fuser (simplex; 220-240V) RM2-6436-000CN Internal components (5 of 5)

on page 3009
Fuser power supply PCA (110-127V) RM2-6440-000CN Internal components (2 of 5)

on page 3003
Fuser power supply PCA (220-240V) RM2-6441-000CN Internal components (2 of 5)

on page 3003

Gear, control panel friction (M377, M477) B3Q09-40003 M377, M477 covers and control
panel on page 2999
Integrated scanner assembly (M377) CF377-60124 Document feeder and scanner

(M377, M477) on page 2995
Integrated scanner assembly (M477) CF377-60104 Document feeder and scanner

(M377, M477) on page 2995
Integrated scanner assembly lift assembly (M377, M477) B3Q10-60128 Document feeder and scanner
(M377, M477) on page 2995
Intermediate transfer belt (ITB) RM2-6454-000CN Internal components (3 of 5)

on page 3005
Laser/scanner assembly RM2-5612-000CN Internal components (1 of 5)

on page 3001
Lifter drive assembly (550-sheet feeder) RM2-6493-000CN 550-sheet paper feeder main
Lifter drive assembly RM2-6370-000CN Internal components (4 of 5)

on page 3007
Low-voltage power supply (110-127V) RM2-7913-000CN Internal components (2 of 5)

on page 3003
Low-voltage power supply (220-240V) RM2-7914-000CN Internal components (2 of 5)

on page 3003
Memory PCA RM2-7374-000CN Internal components (1 of 5)

on page 3001
Motor, developing (M3) RM2-7344-000CN Internal components (3 of 5)

on page 3005
Motor, drum (M2) RM2-7342-000CN Internal components (3 of 5)

on page 3005
Motor, fuser (M4) RM2-7348-000CN Internal components (3 of 5)

on page 3005
Motor, pickup (M1) RM2-7350-000CN Internal components (4 of 5)

on page 3007
Near-field communication (NFC) PCA (M452dw/M477fdw) B4K93-60001 Internal components (5 of 5)

on page 3009
Pad, separation RM2-6406-000CN Internal components (3 of 5)

on page 3005
Paper feed assembly (550-sheet feeder) RM2-6494-000CN 550-sheet paper feeder main
Paper feeder driver PCA (550-sheet feeder) RM2-7366-000CN 550-sheet paper feeder main
Paper pickup assembly (550-sheet feeder) RM2-6490-000CN 550-sheet paper feeder main
Paper pickup assembly (duplex models) RM2-6387-000CN Internal components (5 of 5)

on page 3009

Paper pickup assembly RM2-6372-000CN Internal components (4 of 5)

on page 3007
Paper pickup roller assembly (550-sheet feeder) RM2-5576-000CN 550-sheet paper feeder main
Photointerrupter WG8-5935-000CN Internal components (3 of 5)

on page 3005
Pickup motor (M9) (550-sheet feeder) RM2-7350-000CN 550-sheet paper feeder main
Registration assembly RM2-6374-000CN Internal components (4 of 5)

on page 3007
Remote antenna (M452nw/dw) 0960-3467 Internal components (2 of 5)

on page 3003
Reverse drive assembly (duplex models) RM2-6389-000CN Internal components (5 of 5)

on page 3009
Roller, feed assembly RM2-5577-000CN Internal components (4 of 5)

on page 3007
Roller, paper pickup assembly RM2-5576-000CN Internal components (4 of 5)

on page 3007
Roller, paper pickup RL1-2593-000CN Internal components (3 of 5)

on page 3005
Roller, separation RM2-5881-000CN Internal components (4 of 5)

on page 3007
Secondary transfer assembly (duplex models) RM2-6397-000CN Internal components (5 of 5)

on page 3009
Secondary transfer assembly (simplex models) RM2-6430-000CN Internal components (5 of 5)

on page 3009
Secondary transfer roller RM2-6455-000CN Internal components (5 of 5)

on page 3009
Sensor, density detect RM2-7399-000CN Internal components (3 of 5)

on page 3005
Sensor, environment PCA RM2-7376-000CN Internal components (3 of 5)

on page 3005
Separation roller assembly (550-sheet feeder) RM2-5881-000CN 550-sheet paper feeder main
Separator pad (M377, M477) B3Q10-40080 Document feeder and scanner

(M377, M477) on page 2995
Shaft, document feeder pick extension (M377, M477) B3Q10-40081 Document feeder and scanner
(M377, M477) on page 2995
Shield, RFI SSA FFC (M377, M477) CF377-00006 M377, M477 covers and control
panel on page 2999
Slider pin, integrated scanner assembly lift (M377, M477) B3Q10-40041 Document feeder and scanner
(M377, M477) on page 2995

Spring, separator pad (M377, M477) B3Q10-00019 Document feeder and scanner
(M377, M477) on page 2995
Support, separator pad (M377, M477) B3Q10-40079 Document feeder and scanner
(M377, M477) on page 2995
Switch assembly, power RM2-6373-000CN Internal components (1 of 5)

on page 3001
Switch cable assembly (550-sheet feeder) RM2-7897-000CN 550-sheet paper feeder main
Switch, cable front door assembly RM2-7889-000CN Internal components (1 of 5)

on page 3001
Switch, cassette cable assembly RM2-7896-000CN Internal components (1 of 5)

on page 3001
Walk-up USB port CF368-60001 Internal components (5 of 5)

on page 3009
Wireless bracket (M377, M477fnw/fdw) CF377-40007 Internal components (2 of 5)

on page 3003
Wireless cable (M377, M477fnw/fdw) CF377-60115 Internal components (2 of 5)

on page 3003
Wireless PCA (M377, M477fnw/fdw) 1150-7967 Internal components (1 of 5)

on page 3001
Wireless PCA (M452nw/dw) 0960-3295 Internal components (1 of 5)

on page 3001

Numerical parts list
Table 2-18 Numerical parts list
Part number Description Table and page
0960-3295 Wireless PCA (M452nw/dw) Internal components (1 of 5)

on page 3001
0960-3467 Remote antenna (M452nw/dw) Internal components (2 of 5)

on page 3003
1150-7967 Wireless PCA (M377, M477fnw/fdw) Internal components (1 of 5)

on page 3001
B3Q09-40003 Gear, control panel friction (M377, M477) M377, M477 covers and control
panel on page 2999
B3Q10-00019 Spring, separator pad (M377, M477) Document feeder and scanner
(M377, M477) on page 2995
B3Q10-40013 Cover, document feeder outer (M377, M477) Document feeder and scanner
(M377, M477) on page 2995
B3Q10-40041 Slider pin, integrated scanner assembly lift (M377, M477) Document feeder and scanner
(M377, M477) on page 2995
B3Q10-40055 Control panel mount chassis 4.3 (M377, M477) M377, M477 covers and control
panel on page 2999
B3Q10-40074 Bearing extension (M377, M477) Document feeder and scanner

(M377, M477) on page 2995
B3Q10-40079 Support, separator pad (M377, M477) Document feeder and scanner
(M377, M477) on page 2995
B3Q10-40080 Separator pad (M377, M477) Document feeder and scanner

(M377, M477) on page 2995
B3Q10-40081 Shaft, document feeder pick extension (M377, M477) Document feeder and scanner
(M377, M477) on page 2995
B3Q10-60105 Document feeder pick assembly (M377, M477) Document feeder and scanner
(M377, M477) on page 2995
B3Q10-60107 Document feeder input tray assembly (M377, M477) Document feeder and scanner
(M377, M477) on page 2995
CF377-60124 Integrated scanner assembly (M377) Document feeder and scanner

(M377, M477) on page 2995
B3Q10-60128 Integrated scanner assembly lift assembly (M377, M477) Document feeder and scanner
(M377, M477) on page 2995
B4K93-60001 Near-field communication (NFC) PCA (M452dw/M477fdw) Internal components (5 of 5)

on page 3009
B5L25-60101 Control panel, touchscreen (M377, M477) M377, M477 covers and control
panel on page 2999
CF206-60001 Fax PCA (M477; US) Internal components (1 of 5)

on page 3001
CF207-60001 Fax PCA (M477; Europe) Internal components (1 of 5)

on page 3001
ENWW Numerical parts list 3023

Table 2-18 Numerical parts list (continued)
CF208-60001 Fax PCA (M477; Brazil) Internal components (1 of 5)

on page 3001
CF368-60001 Walk-up USB port Internal components (5 of 5)

on page 3009
CF377-00006 Shield, RFI SSA FFC (M377, M477) M377, M477 covers and control
panel on page 2999
CF377-40003 Cover, 4.3” control panel back (M377, M477) M377, M477 covers and control
panel on page 2999
CF377-40004 FFC cover (M377, M477) M377, M477 covers and control
panel on page 2999
CF377-40005 Fax cover (M477) M377, M477 covers and control

panel on page 2999
CF377-40006 Fax cable cover (M477) M377, M477 covers and control
panel on page 2999
CF377-40007 Wireless bracket (M377, M477fnw/fdw) Internal components (2 of 5)

on page 3003
CF377-60001 Formatter PCA (M477fnw) Internal components (1 of 5)

on page 3001
CF377-60104 Integrated scanner assembly (M477) Document feeder and scanner

(M377, M477) on page 2995
CF377-60105 Cable, fax (M477) Internal components (2 of 5)

on page 3003
CF377-60113 Assembly, control panel mount chassis 4.3 (M377, M477) M377, M477 covers and control
panel on page 2999
CF377-60115 Wireless cable (M377, M477fnw/fdw) Internal components (2 of 5)

on page 3003
CF377-67018 Formatter PCA (M477fnw—China only) Internal components (1 of 5)

on page 3001
CF378-60002 Formatter PCA (M477fdn) Internal components (1 of 5)

on page 3001
CF378-67018 Formatter PCA (M477fdn—China only) Internal components (1 of 5)

on page 3001
CF378-67901 Formatter PCA (M377dw-China only) Internal components (1 of 5)

on page 3001
CF378-67902 Formatter PCA (M377dw) Internal components (1 of 5)

on page 3001
CF379-60001 Formatter PCA, generic (M477) Internal components (1 of 5)

on page 3001
CF379-60003 Formatter PCA (M477fdw) Internal components (1 of 5)

on page 3001
CF379-67018 Formatter PCA (M477fdw—China only) Internal components (1 of 5)

on page 3001

CF388-60003 Formatter PCA (M452nw) Internal components (1 of 5)

on page 3001
CF388-60113 Control panel, touchscreen (M452dw) M452 covers and control panels
on page 2997
CF388-60116 Cable, FFC (M377, M477) Internal components (2 of 5)

on page 3003
CF388-67018 Formatter PCA (M452nw—China only) Internal components (1 of 5)

on page 3001
CF389-60001 Formatter PCA, generic (M452nw/dn) Internal components (1 of 5)

on page 3001
CF389-60002 Formatter PCA (M452dn) Internal components (1 of 5)

on page 3001
CF389-67018 Formatter PCA (M452dn—China only) Internal components (1 of 5)

on page 3001
CF394-60001 Formatter PCA, generic (M452dw) Internal components (1 of 5)

on page 3001
CF394-60002 Formatter PCA (M452dw) Internal components (1 of 5)

on page 3001
CF394-67018 Formatter PCA (M452dw—China only) Internal components (1 of 5)

on page 3001
RC4-2201-000CN Cover, left (550-sheet feeder) 550-sheet paper feeder covers

on page 3011
RC4-2202-000CN Cover, right (550-sheet feeder) 550-sheet paper feeder covers

on page 3011
RC4-2203-000CN Cover, rear (550-sheet feeder) 550-sheet paper feeder covers

on page 3011
RC4-2224-000CN Cover, cassette (550-sheet feeder) 550-sheet paper feeder covers

on page 3011
RC4-4853-000CN Cover, right (M452) M452 covers and control panels

on page 2997
RC4-4854-000CN Cover, left (M452) M452 covers and control panels

on page 2997
RC4-4855-000CN Cover, rear (simplex models) M452 covers and control panels
on page 2997
RC4-4855-000CN Cover, rear (simplex models) M377, M477 covers and control
panel on page 2999
RC4-5130-000CN Door, rear (simplex models) M452 covers and control panels
on page 2997
RC4-5130-000CN Door, rear (simplex models) M377, M477 covers and control
panel on page 2999
RC4-5131-000CN Cover, rear lower (simplex models) M452 covers and control panels
on page 2997

RC4-5131-000CN Cover, rear lower (simplex models) M377, M477 covers and control
panel on page 2999
RC4-5334-000CN Cover, cassette M452 covers and control panels

on page 2997
RC4-5334-000CN Cover, cassette M377, M477 covers and control

panel on page 2999
RC4-6044-000CN Cover, right (M377, M477) M377, M477 covers and control
panel on page 2999
RC4-6045-000CN Cover, left (M377, M477) M377, M477 covers and control
panel on page 2999
RK2-6270-000CN Fan (FM2) Internal components (1 of 5)

on page 3001
RK2-6270-000CN Fan (FM1) Internal components (2 of 5)

on page 3003
RK2-6298-000CN Cable, flexible flat Internal components (2 of 5)

on page 3003

on page 3001

on page 3001
RL1-2593-000CN Roller, paper pickup Internal components (3 of 5)

on page 3005
RM2-5576-000CN Roller, paper pickup assembly Internal components (4 of 5)

on page 3007
RM2-5576-000CN Paper pickup roller assembly (550-sheet feeder) 550-sheet paper feeder main
RM2-5577-000CN Roller, feed assembly Internal components (4 of 5)

on page 3007
RM2-5577-000CN Feed roller assembly (550-sheet feeder) 550-sheet paper feeder main
RM2-5612-000CN Laser/scanner assembly Internal components (1 of 5)

on page 3001
RM2-5881-000CN Roller, separation Internal components (4 of 5)

on page 3007
RM2-5881-000CN Separation roller assembly (550-sheet feeder) 550-sheet paper feeder main
RM2-6366-000CN Feed guide assembly, rear Internal components (4 of 5)

on page 3007
RM2-6366-000CN Feed guide assembly, rear (550-sheet feeder) 550-sheet paper feeder main
RM2-6368-000CN Feed guide assembly, front Internal components (4 of 5)

on page 3007

RM2-6370-000CN Lifter drive assembly Internal components (4 of 5)

on page 3007
RM2-6372-000CN Paper pickup assembly Internal components (4 of 5)

on page 3007
RM2-6373-000CN Switch assembly, power Internal components (1 of 5)

on page 3001
RM2-6374-000CN Registration assembly Internal components (4 of 5)

on page 3007
RM2-6377-000CN Cassette (Tray 2) assembly Internal components (3 of 5)

on page 3005
RM2-6383-000CN Duplexing door assembly (duplex models) M452 covers and control panels
on page 2997
RM2-6383-000CN Duplexing door assembly (duplex models) M377, M477 covers and control
panel on page 2999
RM2-6387-000CN Paper pickup assembly (duplex models) Internal components (5 of 5)

on page 3009
RM2-6389-000CN Reverse drive assembly (duplex models) Internal components (5 of 5)

on page 3009
RM2-6390-000CN Door, front assembly M452 covers and control panels

on page 2997
RM2-6390-000CN Door, front assembly M377, M477 covers and control

panel on page 2999
RM2-6397-000CN Secondary transfer assembly (duplex models) Internal components (5 of 5)

on page 3009
RM2-6401-000CN Cartridge tray assembly Internal components (4 of 5)

on page 3007
RM2-6406-000CN Pad, separation Internal components (3 of 5)

on page 3005
RM2-6418-000CN Fuser (duplex; 110-127V) Internal components (5 of 5)

on page 3009
RM2-6430-000CN Secondary transfer assembly (simplex models) Internal components (5 of 5)

on page 3009
RM2-6431-000CN Fuser (simplex; 110-127V) Internal components (5 of 5)

on page 3009
RM2-6433-000CN Cover, top and control panel (M452nw) M452 covers and control panels
on page 2997
RM2-6435-000CN Fuser (duplex; 220-240V) Internal components (5 of 5)

on page 3009
RM2-6436-000CN Fuser (simplex; 220-240V) Internal components (5 of 5)

on page 3009
RM2-6440-000CN Fuser power supply PCA (110-127V) Internal components (2 of 5)

on page 3003

RM2-6441-000CN Fuser power supply PCA (220-240V) Internal components (2 of 5)

on page 3003
RM2-6442-000CN Cover, top and control panel (M452dn) M452 covers and control panels
on page 2997
RM2-6454-000CN Intermediate transfer belt (ITB) Internal components (3 of 5)

on page 3005
RM2-6455-000CN Secondary transfer roller Internal components (5 of 5)

on page 3009
RM2-6456-000CN Cover, top (M452dw) M452 covers and control panels

on page 2997
RM2-6466-000CN Cover, top (M477fnw/fdn) M377, M477 covers and control

panel on page 2999
RM2-6468-000CN Cover, top (M377, M477fdw) M377, M477 covers and control
panel on page 2999
RM2-6486-000CN Cassette assembly (550-sheet feeder) 550-sheet paper feeder main

RM2-6490-000CN Paper pickup assembly (550-sheet feeder) 550-sheet paper feeder main
RM2-6492-000CN Feed guide assembly, front (550-sheet feeder) 550-sheet paper feeder main
RM2-6493-000CN Lifter drive assembly (550-sheet feeder) 550-sheet paper feeder main
RM2-6494-000CN Paper feed assembly (550-sheet feeder) 550-sheet paper feeder main
RM2-7342-000CN Motor, drum (M2) Internal components (3 of 5)

on page 3005
RM2-7344-000CN Motor, developing (M3) Internal components (3 of 5)

on page 3005
RM2-7348-000CN Motor, fuser (M4) Internal components (3 of 5)

on page 3005
RM2-7350-000CN Motor, pickup (M1) Internal components (4 of 5)

on page 3007
RM2-7350-000CN Pickup motor (M9) (550-sheet feeder) 550-sheet paper feeder main
RM2-7366-000CN Paper feeder driver PCA (550-sheet feeder) 550-sheet paper feeder main
RM2-7369-000CN Driver PCA Internal components (2 of 5)

on page 3003
RM2-7374-000CN Memory PCA Internal components (1 of 5)

on page 3001
RM2-7376-000CN Sensor, environment PCA Internal components (3 of 5)

on page 3005

RM2-7399-000CN Sensor, density detect Internal components (3 of 5)

on page 3005
RM2-7889-000CN Switch, cable front door assembly Internal components (1 of 5)

on page 3001
RM2-7896-000CN Switch, cassette cable assembly Internal components (1 of 5)

on page 3001
RM2-7897-000CN Switch cable assembly (550-sheet feeder) 550-sheet paper feeder main
RM2-7909-000CN Engine controller PCA (duplex models) Internal components (1 of 5)

on page 3001
RM2-7910-000CN Engine controller PCA (simplex models) Internal components (1 of 5)

on page 3001
RM2-7913-000CN Low-voltage power supply (110-127V) Internal components (2 of 5)

on page 3003
RM2-7914-000CN Low-voltage power supply (220-240V) Internal components (2 of 5)

on page 3003
VS1-7257-007CN Connector, drawer (550-sheet feeder) 550-sheet paper feeder main

VS1-7258-007CN Connector, drawer Internal components (1 of 5)

on page 3001
WG8-5935-000CN Photointerrupter Internal components (3 of 5)

on page 3005

Index
Symbols/Numerics cassette (Tray 2) assembly cover, document feeder outer (M377,

550-sheet paper feeder location 3005, 3016, 3027 M477)
parts lists and diagrams 3010 part number 3005, 3016, 3027 location 2995, 3016, 3023
cassette assembly (550-sheet feeder) part number 2995, 3016, 3023
A location 3015, 3016, 3028 cover, left (550-sheet feeder)
after-service checklist 6 part number 3015, 3016, 3028 location 3011, 3017, 3025
assembly, control panel mount cautions iii part number 3011, 3017, 3025
chassis 4.3 (M377, M477) connector, drawer cover, left (M377, M477)
location 2999, 3016, 3024 location 3001, 3016, 3029 location 2999, 3017, 3026
part number 2999, 3016, 3024 part number 3001, 3016, 3029 part number 2999, 3017, 3026
connector, drawer (550-sheet feeder) cover, left (M452)
B location 3013, 3016, 3029 location 2997, 3017, 3025
bearing extension (M377, M477) part number 3013, 3016, 3029 part number 2997, 3017, 3025
location 2995, 3016, 3023 control panel mount chassis 4.3 cover, rear (550-sheet feeder)
part number 2995, 3016, 3023 (M377, M477) location 3011, 3017, 3025
before-service checklist 6 location 2999, 3016, 3023 part number 3011, 3017, 3025
part number 2999, 3016, 3023 cover, rear (simplex models)
C control panel, touchscreen (M377, location 2997, 2999, 3017,
cable, fax (M477) M477) 3025
part number 3003, 3016, 3024 location 2999, 3016, 3023 part number 2997, 2999, 3017,
cable, FFC (M377,M477) part number 2999, 3016, 3023 3025
part number 3003, 3016, 3025 control panel, touchscreen (M452dw) cover, rear lower (simplex models)
cable, flexible flat location 2997, 3016, 3025 location 2997, 2999, 3017,
location 3001, 3003, 3016, part number 2997, 3016, 3025 3025, 3026
3026 conventions, document iii part number 2997, 2999, 3017,
part number 3001, 3003, 3016, cover, 4.3” control panel back (M377, 3025, 3026
3026 M477) cover, right (550-sheet feeder)
cartridge fan location 2999, 3016, 3024 location 3011, 3017, 3025
removing and replacing 660 part number 2999, 3016, 3024 part number 3011, 3017, 3025
cartridge tray assembly cover, cassette cover, right (M377, M477)
location 3007, 3016, 3027 location 2997, 2999, 3016, location 2999, 3017, 3026
part number 3007, 3016, 3027 3026 part number 2999, 3017, 3026
cartridge, toner part number 2997, 2999, 3016, cover, right (M452)
ordering 2990 3026 location 2997, 3017, 3025
part numbers 2990 cover, cassette (550-sheet feeder) part number 2997, 3017, 3025
cartridges location 3011, 3016, 3025 cover, top (M377, M477fdw)
removing and replacing 12 part number 3011, 3016, 3025 location 2999, 3017, 3028
part number 2999, 3017, 3028
ENWW Index 3031

cover, top (M452dw) drawer connector (550-sheet paper fax cable cover (M477)
location 2997, 3017, 3028 feeder) location 2999, 3018, 3024
part number 2997, 3017, 3028 removing and replacing 2963 part number 2999, 3018, 3024
cover, top (M477fnw/fdn) driver PCA fax cover (M477)
cover, top and control panel removing and replacing 839 fax PCA (M477 models)
(M452dn) driver PCA (550-sheet paper feeder) removing and replacing 2420
location 2997, 3017, 3028 removing and replacing 2974 fax PCA (M477; Brazil)
part number 2997, 3017, 3028 drum motor location 3001, 3018, 3024
cover, top and control panel removing and replacing 869 part number 3001, 3018, 3024
(M452nw) duplex drive assembly (duplex fax PCA (M477; Europe)
location 2997, 3017, 3027 models) location 3001, 3018, 3023
covers and control panels (M377, duplexer door fax PCA (M477; US)
M477) removing and replacing 180 location 3001, 3018, 3023
parts lists and diagrams 2998 duplexing door assembly (duplex part number 3001, 3018, 3023
covers and control panels (M452) models) feed guide assembly, front
parts lists and diagrams 2996 location 2997, 2999, 3018, location 3007, 3018, 3026
3027 part number 3007, 3018, 3026
D part number 2997, 2999, 3018, feed guide assembly, front (550-
developer motor 3027 sheet feeder)
removing and replacing 936 location 3015, 3018, 3028
document conventions iii E part number 3015, 3018, 3028
document feeder and scanner whole electrostatic discharge (ESD) 4 feed guide assembly, rear
units engine controller PCA location 3007, 3018, 3026
parts lists and diagrams 2994 removing and replacing 1222 part number 3007, 3018, 3026
document feeder input tray assembly engine controller PCA (duplex feed guide assembly, rear (550-sheet
(M377, M477) models) feeder)
document feeder pick assembly engine controller PCA (simplex feed roller assembly (550-sheet
(M377, M477) models) feeder)
documentation environmental sensor FFC cover (M377, M477)
links 9 removing and replacing 2393 location 2999, 3018, 3024
door, front assembly ESD electrostatic discharge (ESD) 4 part number 2999, 3018, 3024
location 2997, 2999, 3017, external panels, covers, and doors field-replaceable units (FRUs)
3027 removing and replacing 78 replacing 3
part number 2997, 2999, 3017, formatter PCA
3027 F removing and replacing 2361
door, rear (simplex models) fan (FM1) formatter PCA, (M377dw)
location 2997, 2999, 3017, location 3003, 3018, 3026 location 3001, 3018, 3024
3018, 3025 part number 3003, 3018, 3026 part number 3001, 3018, 3024
part number 2997, 2999, 3017, fan (FM2) formatter PCA, (M377dw-China only)
3018, 3025 location 3001, 3018, 3026 location 3001, 3018, 3024
drawer connector part number 3001, 3018, 3026 part number 3001, 3018, 3024
removing and replacing 2639
3032 Index ENWW

formatter PCA, (M452dn) front door integrated scanner assembly (M377,
location 3001, 3019, 3025 removing and replacing 146 M477 models)
part number 3001, 3019, 3025 front feed guide assembly removing and replacing 569
formatter PCA, (M452dn—China only) removing and replacing 1411 integrated scanner assembly (M477)
location 3001, 3019, 3025 front feed guide assembly (550-sheet location 2995, 3020, 3024
part number 3001, 3019, 3025 paper feeder) part number 2995, 3020, 3024
formatter PCA, (M452dw) removing and replacing 2801 integrated scanner assembly lift
location 3001, 3019, 3025 FRUs (field-replaceable units) assembly (M377, M477)
part number 3001, 3019, 3025 replacing 3 location 2995, 3020, 3023
formatter PCA, (M452dw—China fuser (duplex models) part number 2995, 3020, 3023
only) removing and replacing 2027 intermediate transfer belt (ITB)
location 3001, 3019, 3025 fuser (duplex; 110-127V) location 3005, 3020, 3028
part number 3001, 3019, 3025 location 3009, 3019, 3027 part number 3005, 3020, 3028
formatter PCA, (M452nw) part number 3009, 3019, 3027 removing and replacing 1016
location 3001, 3019, 3025 fuser (duplex; 220-240V) internal components, printer
part number 3001, 3019, 3025 location 3009, 3019, 3027 parts lists and diagrams 3000
formatter PCA, (M452nw—China part number 3009, 3019, 3027 internal parts and assemblies
only) fuser (simplex models) removing and replacing 595
location 3001, 3019, 3025 removing and replacing 1939
part number 3001, 3019, 3025 fuser (simplex; 110-127V) K
formatter PCA, (M477fdn) location 3009, 3019, 3027 kit
location 3001, 3019, 3024 part number 3009, 3019, 3027 instructions, toner cartridges 12
part number 3001, 3019, 3024 fuser (simplex; 220-240V)
formatter PCA, (M477fdn—China location 3009, 3019, 3027 L
only) part number 3009, 3019, 3027 laser scanner
location 3001, 3019, 3024 fuser motor warnings for servicing 3
part number 3001, 3019, 3024 removing and replacing 2148 laser scanner ( M377, M477 models)
formatter PCA, (M477fdw) fuser power supply removing and replacing 1855
location 3001, 3019, 3024 removing and replacing 2116 laser scanner (M452 models)
part number 3001, 3019, 3024 fuser power supply PCA (110-127V) removing and replacing 1795
formatter PCA, (M477fdw—China location 3003, 3019, 3027 laser/scanner assembly
only) part number 3003, 3019, 3027 location 3001, 3020, 3026
location 3001, 3019, 3024 fuser power supply PCA (220-240V) part number 3001, 3020, 3026
part number 3001, 3019, 3024 location 3003, 3019, 3028 left cover (550-sheet paper feeder)
formatter PCA, (M477fnw) part number 3003, 3019, 3028 removing and replacing 2673
location 3001, 3019, 3024 left cover (M377, M477 models)
part number 3001, 3019, 3024 G removing and replacing 127
formatter PCA, (M477fnw—China gear, control panel friction (M377, left cover (M452 models)
only) M477) removing and replacing 94
location 3001, 3019, 3024 location 2999, 3020, 3023 lifter drive assembly
part number 3001, 3019, 3024 part number 2999, 3020, 3023 location 3007, 3020, 3027
formatter PCA, generic (M452dw) part number 3007, 3020, 3027
location 3001, 3019, 3025 I removing and replacing 1251
part number 3001, 3019, 3025 installation 5 lifter drive assembly (550-sheet
formatter PCA, generic (M452nw/dn) screws 5 feeder)
location 3001, 3019, 3025 See also replacing parts location 3015, 3020, 3028
part number 3001, 3019, 3025 integrated scanner assembly (M377) part number 3015, 3020, 3028
formatter PCA, generic (M477) location 2995, 3020, 3023 lifter drive assembly (550-sheet
location 3001, 3019, 3024 part number 2995, 3020, 3023 paper feeder)
part number 3001, 3019, 3024 removing and replacing 2721
ENWW Index 3033

low-voltage power supply paper feed assembly (550-sheet pickup motor (M9) (550-sheet feeder)
(110-127V) paper feeder) location 3015, 3021, 3028
location 3003, 3020, 3029 removing and replacing 2900 part number 3015, 3021, 3028
part number 3003, 3020, 3029 paper feeder driver PCA (550-sheet power supply fan
low-voltage power supply feeder) removing and replacing 689
(220-240V) location 3013, 3020, 3028 power switch assembly
location 3003, 3020, 3029 part number 3013, 3020, 3028 removing and replacing 597
part number 3003, 3020, 3029 paper pickup assembly
low-voltage power supply (LVPS) location 3007, 3021, 3027 R
removing and replacing 719 part number 3007, 3021, 3027 re-pickup assembly (duplex models)
paper pickup assembly (550-sheet removing and replacing 1166
M feeder) rear cover (550-sheet paper feeder)
memory PCA location 3015, 3020, 3028 removing and replacing 2680
location 3001, 3020, 3028 part number 3015, 3020, 3028 rear door (simplex models)
part number 3001, 3020, 3028 paper pickup assembly (duplex removing and replacing 317
removing and replacing 1708 models) rear feed guide assembly
motor, developing (M3) location 3009, 3020, 3027 removing and replacing 1508
location 3005, 3020, 3028 part number 3009, 3020, 3027 rear feed guide assembly (550-sheet
part number 3005, 3020, 3028 paper pickup roller assembly (550- paper feeder)
motor, drum (M2) sheet feeder) removing and replacing 2850
location 3005, 3020, 3028 location 3015, 3021, 3026 rear lower cover (simplex models)
part number 3005, 3020, 3028 part number 3015, 3021, 3026 removing and replacing 272
motor, fuser (M4) part numbers rear top cover (simplex models)
location 3005, 3020, 3028 toner cartridge 2990 removing and replacing 227
part number 3005, 3020, 3028 parts lists and diagrams 2985 registration assembly
motor, pickup (M1) 550-sheet paper feeder 3010 location 3007, 3021, 3027
location 3007, 3020, 3028 covers and control panels (M377, part number 3007, 3021, 3027
part number 3007, 3020, 3028 M477) 2998 removing and replacing 1606
covers and control panels registration density sensor
N (M452) 2996 removing and replacing 1082
near-field communication (NFC) PCA document feeder and scanner remote antenna (M452nw/dw)
(M452dw/M477fdw) whole units 2994 part number 3003, 3021, 3023
part number 3009, 3020, 3023 internal components, printer removing and replacing
NFC PCA (M452dw and M477dw 3000 cartridge fan 660
models) using 2992 developer motor 936
removing and replacing 2460 photointerrupter drawer connector 2639
notes iii location 3005, 3021, 3029 drawer connector (550-sheet
part number 3005, 3021, 3029 paper feeder) 2963
O pickup assembly driver PCA 839
ordering removing and replacing 1321 driver PCA (550-sheet paper
toner cartridge 2990 pickup assembly (550-sheet paper feeder) 2974
feeder) drum motor 869
P removing and replacing 2758 duplex drive assembly (duplex
pad, separation pickup motor models) 2181
location 3005, 3020, 3027 removing and replacing 778 duplexer door 180
part number 3005, 3020, 3027 pickup motor (550-sheet paper engine controller PCA 1222
paper feed assembly (550-sheet feeder) environmental sensor 2393
feeder) removing and replacing 2955 external panels, covers, and
location 3015, 3020, 3028 doors 78
part number 3015, 3020, 3028 fax PCA (M477 models) 2420
3034 Index ENWW

formatter PCA 2361 rear lower cover (simplex before-service checklist 6
front door 146 models) 272 tools, required 4
front feed guide assembly 1411 rear top cover (simplex models) replacing parts
front feed guide assembly (550- 227 about 3
sheet paper feeder) 2801 registration assembly 1606 after-service checklist 6
fuser (duplex models) 2027 registration density sensor before-service checklist 6
fuser (simplex models) 1939 1082 screws 5
fuser motor 2148 right cover (550-sheet paper tools, required 4
fuser power supply 2116 feeder) 2667 reverse drive assembly (duplex
integrated scanner assembly right cover (M377, M477 models)
(M377, M477 models) 569 models) 109 location 3009, 3021, 3027
intermediate transfer belt (ITB) right cover (M452 models) 79 part number 3009, 3021, 3027
1016 rollers 23 right cover (550-sheet paper feeder)
internal parts and assemblies secondary transfer assembly removing and replacing 2667
595 (duplex models) 1009 right cover (M377, M477 models)
laser scanner ( M377, M477 secondary transfer assembly removing and replacing 109
models) 1855 (simplex models) 1003 right cover (M452 models)
laser scanner (M452 models) secondary transfer roller 72 removing and replacing 79
1795 switch cable assembly (550-sheet roller, feed assembly
left cover (550-sheet paper paper feeder) 2692 location 3007, 3021, 3026
feeder) 2673 toner cartridge tray 626 part number 3007, 3021, 3026
left cover (M377, M477 models) toner cartridges 12 roller, paper pickup
127 top cover (M377, M477 models) location 3005, 3021, 3026
left cover (M452 models) 94 405 part number 3005, 3021, 3026
lifter drive assembly 1251 top cover (M452 models) 364 roller, paper pickup assembly
lifter drive assembly (550-sheet touchscreen control panel (M377, location 3007, 3021, 3026
paper feeder) 2721 M477 models) 507 part number 3007, 3021, 3026
low-voltage power supply touchscreen control panel roller, separation
(LVPS) 719 (M452dw model) 470 location 3007, 3021, 3026
memory PCA 1708 tray 1 pickup roller 24 part number 3007, 3021, 3026
NFC PCA (M452dw and M477dw tray 1 separation pad 29 rollers
models) 2460 Tray 2 19 removing and replacing 23
paper feed assembly (550-sheet tray 2 pickup and feed rollers 34
paper feeder) 2900 tray 2 separation roller 47 S
pickup assembly 1321 Tray 3 21 screwdrivers, required 4
pickup assembly (550-sheet tray 3 pickup and feed rollers 59 screws
paper feeder) 2758 tray 3 separation roller 66 installing 5
pickup motor 778 trays 18 types of 5
pickup motor (550-sheet paper walk-up USB port (M377, M477 secondary transfer assembly (duplex
feeder) 2955 models) 2577 models)
power supply fan 689 walk-up USB port (M452dw location 3009, 3021, 3027
power switch assembly 597 model) 2544 part number 3009, 3021, 3027
re-pickup assembly (duplex wireless antenna (M452nw/dw removing and replacing 1009
models) 1166 models) 2278 secondary transfer assembly
rear cover (550-sheet paper wireless PCA (M377, (simplex models)
feeder) 2680 M477fnw/fdw models) 2336 location 3009, 3021, 3027
rear door (simplex models) 317 wireless PCA (M452nw/dw part number 3009, 3021, 3027
rear feed guide assembly 1508 models) 2317 removing and replacing 1003
rear feed guide assembly (550- removing parts secondary transfer roller
sheet paper feeder) 2850 after-service checklist 6 location 3009, 3021, 3028
ENWW Index 3035

part number 3009, 3021, 3028 switch, cassette cable assembly walk-up USB port (M452dw model)
removing and replacing 72 location 3001, 3022, 3029 removing and replacing 2544
sensor, density detect part number 3001, 3022, 3029 warnings iii
location 3005, 3021, 3029 wireless antenna (M452nw/dw
part number 3005, 3021, 3029 T models)
sensor, environment PCA tips iii removing and replacing 2278
location 3005, 3021, 3028 toner cartridge wireless bracket (M477fnw/fdw)
part number 3005, 3021, 3028 ordering 2990 part number 3003, 3022, 3024
separation roller assembly (550- part numbers 2990 wireless cable (M377, M477fnw/fdw)
sheet feeder) toner cartridge tray part number 3003, 3022, 3024
location 3015, 3021, 3026 removing and replacing 626 wireless PCA (M377, M477fnw/fdw
part number 3015, 3021, 3026 toner cartridges models)
separator pad (M377, M477) removing and replacing 12 removing and replacing 2336
location 2995, 3021, 3023 tools, required 4 wireless PCA (M452nw/dw models)
part number 2995, 3021, 3023 top cover (M377, M477 models) removing and replacing 2317
service and support information v, removing and replacing 405 wireless PCA, (M377, M477fnw/fdw)
2, 2986, 2991 top cover (M452 models) location 3001, 3022, 3023
shaft, document feeder pick removing and replacing 364 part number 3001, 3022, 3023
extension (M377, M477) touchscreen control panel (M377, wireless PCA, (M452nw/dw)
location 2995, 3021, 3023 M477 models) location 3001, 3022, 3023
shield, RFI SSA FFC (M377, M477) touchscreen control panel (M452dw
location 2999, 3021, 3024 model)
slider pin, integrated scanner tray 1 pickup roller
assembly lift (M377, M477) removing and replacing 24
location 2995, 3021, 3023 tray 1 separation pad
spring, separator pad (M377, M477) Tray 2
part number 2995, 3022, 3023 tray 2 pickup and feed rollers
static, precautions for 4 removing and replacing 34
supplies tray 2 separation roller
part numbers 9 removing and replacing 47
support, separator pad (M377, M477) Tray 3
part number 2995, 3022, 3023 tray 3 pickup and feed rollers
switch assembly, power removing and replacing 59
location 3001, 3022, 3027 tray 3 separation roller
switch cable assembly (550-sheet trays
feeder) removing and replacing 18
location 3015, 3022, 3029
part number 3015, 3022, 3029 W
switch cable assembly (550-sheet walk-up USB port
paper feeder) part number 3009, 3022, 3024
removing and replacing 2692 walk-up USB port (M377, M477
switch, cable front door assembly models)
part number 3001, 3022, 3029
3036 Index ENWW

Repair Manual: M452nw M452dn M452dw

Uploaded by

Copyright:

Available Formats

Repair Manual: M452nw M452dn M452dw

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Repair Manual: M452nw M452dn M452dw

Uploaded by

Copyright:

Available Formats

Color LaserJet Pro MFP M377

Color LaserJet Pro M452

© Copyright 2016 HP Development Company,

Reproduction, adaptation, or translation

The information contained herein is subject to

The only warranties for HP products and

NOTE: Information that explains a concept or how to complete a task.

Reinstallation tip: Reinstallation helpful hints, shortcuts, or considerations.

Channel partners, go to HP Channel Services Network (CNS) at https://h30125.www3.hp.com/hpcsn.

At these locations, find information on the following topics:

● Install and configure

● Up-to-date control panel message (CPMD) troubleshooting

● Solutions for printer issues and emerging issues

● Remove and replace part instructions and videos

● Warranty and regulatory information

To access HP PartSurfer information from any mobile device, go to http://partsurfermobile.hp.com/ or scan

1 Removal and replacement .............................................................................................................................. 1

2 Parts and diagrams .................................................................................................................................. 2985

Index .......................................................................................................................................................... 3031

Table 1-1 Supplies part numbers ......................................................................................................................................... 9

Figure 1-1 Screwdrivers ........................................................................................................................................................ 4

● For additional service and support

● Removal and replacement strategy

● Order parts by authorized service providers

● Removal and replacement procedures

Channel partners, go to HP Channel Services Network (CSN) at https://h30125.www3.hp.com/hpcsn.

At these locations, find information on the following topics:

● Install and configure

● Up-to-date control panel message (CPMD) troubleshooting

● Solutions for printer issues and emerging issues

● Remove and replace part instructions and videos

● Warranty and regulatory information

To access HP PartSurfer information from any mobile device, go to http://partsurfermobile.hp.com/ or scan

2 Chapter 1 Removal and replacement ENWW

2. Troubleshoot the problem by using the procedures in the troubleshooting chapter.

Considerations during removal and replacement

Do not bend or fold the flat cables during removal or installation.

ENWW Removal and replacement strategy 3

● Small, flat-blade screwdriver

● ESD strap (if one is available)

Figure 1-1 Screwdrivers

4 Chapter 1 Removal and replacement ENWW

Fasteners used in M452 models

● M3x8mm Taptite (metallic)

● M3x6mm Taptite (black)

Fasteners used in M377, M477 models

● M3x8mm Taptite (metallic)

● M3x6mm Taptite (black)

● M4x13.3mm Plastite (black chrome)

● M3x14 Taptite (black)

● M3x8mm Plastite (metallic)

ENWW Removal and replacement strategy 5

1. Remove all paper.

3. Remove the toner cartridge or toner cartridges.

4. Remove the trays.

Secondary service menu

Two-line control panels

1. From the printer control panel, press the OK button.

2. Select the Setup menu, and then press the OK button.