TRANSMISSION LINES PROTECTION

Transmission Line Protection Distance Relays: Introduction: The impedance relays also called distance relays are employed to provide protection to transmission lines connected in a network as they are economic and possess several technical advantages. They are comparatively simple to apply, operate with extremely high speed, and both primary and backup protection features are inherent in them. Moreover, they can be easily modified to work as unit schemes by coordinating them with power line carrier facilities and are suitable for high speed reclosing. The impedance relay is made to respond to the impedance between the relay location and the point where fault is incident. The impedance is proportional to the distance to the fault, (hence the name 'distance relay') and is therefore independent of the fault current levels. Distance Relaying Principle: A distance relay compares the currents and voltages at the relaying point with Current providing the operating torque and the voltage provides the restraining torque. In other words an impedance relay is a voltage restrained overcurrent relay. The equation at the balance point in a simple impedance relay is K1V2 = K2I2 or V/I = K3 where K1, K2 and K3 are constants. In other words, the relay is on the verge of operation at a constant value of V/I ratio, which may be expressed as an impedance. 3

Application of distance relays:

Since the distance relays are fed from the secondaries of line CTs and bus PTs/line CVTs, the line parameters are to be converted into secondary values to set the relay as per requirements. Zsecy = Zpri/Impedance ratio (where Impedance ratio = P.T.Ratio/C.T.Ratio) Hence any changes in C.T .ratio has to be effected along with revision of relay settings only.

For the lines, the impedance in Ohms per KM is approximately as under: ----------------------------------------------------------------------------------KV Z1 (= Z2 ) Line Angle ----------------------------------------------------------------------------------132 KV 0.4 60 to 70 Deg. 220 KV 0.4 70 to 80 Deg.

400 KV 0.3 80 to 85 Deg. ---------------------------------------------------------------------------------The line impedance is to be computed depending on line configuration conductor size and clearness. The values in the table are only representative. A distance relay is stepped for either 3 zones or 4 zones to provide protection.

To ensure proper coordination between distance relays in power system, it is customary to choose relay ohmic setting as follows: 7

---------------------------------------------------------------------------------------------S.No. Zones Reactance Time ---------------------------------------------------------------------------------------------1. Zone-1 80% of ZL Instantaneous (no intentional time delay). 2. 3. 4. Zone-2 Zone-3 Zone-4 100% of ZL + 40-50% of ZSL 100% of ZL + 120% of ZSL 0.3 to 0.4 seconds 0.6 to 0.8 seconds

100% of ZL + 120% 0.9 to 1.5 of ZLL seconds. ----------------------------------------------------------------------------------------------where ZL = Positive sequence impedance of line to be protected. ZSL = Positive sequence impedance of adjacent shortest line. ZLL = Positive sequence impedance of adjacent longest line. Note: i) Where a three zone relay only is available, the zone 3 will be set to cover the adjacent longest line. jj) The zonal timings will be carefully selected to properly grade with the relays on all the feeders emanating from the adjacent bus. 8

Norms of protection adopted for transmission lines in A.P.System:i) 132 KV Lines: A switched type distance scheme supplemented by three numbers directional O/L relays and 1 No. directional E/L relay. 220 KV Lines: Two Distance Schemes: Main-I: Main-II: Non-switched scheme fed from bus PT. A switched scheme fed from line CVT.

ii)

A provision is generally made for the changeover of voltage supply for the distance schemes from the bus PT to line CVT and vice-versa. Each distance scheme is fed from independent CT secondary cores. iii) 400 KV Lines:Two Distance Schemes:Main-I:Main-II:10 Non-switched or Numerical distance schemes Non-switched or Numerical distance schemes

Since the operating characteristics of the relay depend upon the ratio of voltage and current and the phase angle between them, their characteristics can be best represented on an R-X diagram where both V/I ratio and the phase angle can be plotted in terms of an impedance R+jX. Further, the power system impedance like fault impedance, power swings, loads etc. can also be plotted on the same R-X diagram. Therefore response of a particular relay during power swing, faults and other system disturbances can easily be assessed. Types of Distance Relays: (1) (2) (3) (4) (1) Impedance relay Reactance relay Mho relay Modified impedance relay Impedance relay: Characteristics of an impedance relay on R-X diagram is shown in fig

Operation of the impedance relay is independent of the phase angle between V and I. The operating characteristic is a circle with its center at the origin, and hence the relay is nondirectional.

11

12

Characteristic of Directional Impedance Relay: Characteristic of a directional impedance relay in the complex R-X phase is shown in fig. The directional unit of the relay causes separation of the regions of the relay characteristic shown in the figure by a line drawn perpendicular to the line impedance locus. The net result is that tripping will occur only for points that are both within the circles and above the directional unit characteristic. 13

The Reactance-type Distance Relay: Reactance relay measures V/I Sin0 (i.e. Z sin 0 - ). Whenever the reactance measured by the relay is less than the set value, the relay operates. The operating characteristic on R-X diagram is shown in fig The resistance component of impedance has no effect on the operation of reactance relay, the relay responds solely to reactance component of impedance. This relay is inherently non-directional. The relay is most suitable to detect earth faults where the effect of arc resistance is appreciable.

14

15

Mho relay: This is a directional impedance relay, also known as admittance relay. Its characteristic on RX diagram is a circle whose circumference passes through the origin as illustrated in figure showing that the relay is inherently directional and it only operates for faults in the forward direction. Modified impedance relay: Also known as offset Mho relay whose characteristic encloses the origin on R-X diagram as shown in fig This offset mho relay has three main applications: i) ii) iii) Busbar zone backup Carrier starting unit in distance/carrier blocking schemes. Power Swing blocking.

16

Main Features in Distance Scheme Distance schemes consist of the following major components:i) ii) iii) iv) i) Starters. Measuring units. Timers Auxiliary relays Starters: The starting relay (or starter) initiates the distance scheme in the event of a fault within the required reach (more than zone-3). Other functions of the starter are: a) Starting of timer relays for second and third zones. b) Starting of measuring elements. The starters are generally of Mho or impedance type. With Mho type starters: Measuring units for phase and earth faults can be either directional or nondirectional as Mho starter is inherently directional.

17

With impedance type starters: Measuring units have to be directional as impedance starters are non directional. The under impedance relay can be used in conjunction with the directional relay as starter which will then function similar to the Mho starter. ii) Measuring units: They are generally of a mho or reactance or a combination of mho, reactance and resistance types. Phase Fault Units:These measuring units are fed with line to line voltages (such as Vab, Vbc) and difference between line currents (Ia-Ib). They measure the positive sequence impedance from the relay location to the fault point. Three such relays respond correctly to all possible single line to ground faults line to line faults, double line to ground faults and 3-phase faults. They however do not respond correctly to earth faults.

18

Earth Fault Units: These measuring units utilize line to neutral voltage (Van, Vbn Vcn) and phase currents (Ia, Ib, Ic). In order to make these units measure the positive sequence impedance correctly, a zero sequence current compensation is to be provided which is obtained by: KN = (Z0-Z1)/ 3*Z1 (where Z1 = positive sequence impedance of line. Z0 = Zero sequence impedance of line) In the current circuit (1+KN) Ia will be fed for the above measurement. iii) Timers: Timer relays when initiated by starters provide the time lag required for zones. They also will be used for zone extension purpose whenever required. Auxiliary relays: Distance scheme comprises of several auxiliary relays, which perform functions such as flag indications, trippings, signaling, alarm etc.

iv)

19

Additional Features in distance schemes: i) ii) iii) iv) v) vi) i) Power Swing blocking relay VT fuse failure relay. Switch onto fault relay Fault locator Auto-reclosing scheme. Carrier communication scheme. Power Swing blocking: Distance relay which respond to balanced 3-phase changes in the impedance will be affected by power swings. These swings or oscillations occur following a system disturbance such as major load change or a dip in voltage due to delayed fault clearance. In case of fault, the transition from period of impedance locations (25 to 33% of starter impedance) to fault impedance (starter impedance) is sudden whereas during power swings. The PSB relays use this difference to block the tripping during swings. ii) VT fuse failure relay: The distance relays being voltage restraint O/C relays, loss of voltage due to main PT fuse failure or inadvertent removal of fuse in one or more phases will cause the relay operation. The fuse failure relay will sense such condition by the presence of residual voltage without residual current and blocks the relay.

20

iii)

Switch onto fault: When the line is switched on to a close by fault (say after line clear with earth switch closed), the voltage at the relaying point will be zero. Faults of this type will normally be cleared by backup zones. The voltage applied to the relay is low and this condition occurring simultaneously with the operation of starter will cause instantaneous trip by SOTF relay. This SOTF feature will be effective only for about 1-2 seconds after the line is charged. Faults occurring after this time will be measured in the normal way.

iv)

Fault locator: It measures the distance between the relay location and fault location in terms of Z in Ohms, or length in KM or percentage of line length. This relay gets same inputs as the distance relay (connected in series with one of the main relays). The measurement is initiated by trip signal from distance relays. The fault locator gives the exact location of the fault, thereby reducing the time of restoration.

21

v)

Auto Reclosing Schemes:Types of Faults:-

i)

Transient Faults:These are cleared by the immediate tripping of circuit breakers and do not recur when the line is re-energised. Semi-permanent Faults:These require a time interval to disappear before a line is charged again. Permanent Faults:These are to be located and repaired before the line is re-energised.

ii) iii)

About 80-90% of the faults occurring are transient in nature. Hence the automatic reclosure of breaker (after tripping on fault) will result in the line being successfully reenergised, thereby a) b) c) d) 22 Decreasing outage time Improving reliability Improving system stability Reduces fault damage and maintenance time

Dead Time:The time between the Auto-reclosing scheme being energised and the 1st reclosure of the circuit breaker . This is normally set at 1 Sec. Reclaim Time:The time following a successful closing operation measured from the instant the autoreclosing relay closing contacts making which must elapse before the auto-reclosing relay initiated another reclosing attempt. In other words, it may be said to be the time between 1st and 2nd re-closure. Types of Auto-reclosing schemes (based on phase): a) Three phase Auto-reclosing: This type of auto-reclosing causes an immediate drift apart of the two systems and hence no interchange of synchronizing power can take place during the dead time. b) Single Phase Auto-reclosing: In this only the faulty phase (which already has tripped on SLG fault) is reclosed without causing interruption in interchange of synchronising power between two systems through other two healthy phases. 23

Types of Auto-reclosing schemes (case on attempts of reclosure): a) Single Shot Auto-reclosing:In this scheme, breaker is reclosed only once on a given fault before lockout of circuit breaker occurs. High speed auto-reclosing for EHV system is invariably single shot. b) Multi-shot Auto-reclosing:In this scheme, more than one reclosing attempt is made for a given fault before lockout of the circuit breaker occurs. Repeated closure attempts with high fault level would seriously affect the circuit breaker, equipment and system stability. The factors that must be taken into account:i) Circuit Breaker Limitations:Ability of circuit breaker to perform several trip close operations in quick succession. System Conditions:In the percentage of the semi-permanent faults (which could be burnt out) is moderate, for example on the lines through the forest, multishot auto-reclosing is followed.

ii)

24

Types of Auto-reclosing (depending on speed): I) High speed Auto-reclosing:

This aids in fast restoration of supply but should be done by taking into account the following factors:i) ii) II. System disturbance time can be tolerated without loss of system stability. Characteristics of protection schemes and circuit breaker.

Low Speed or Delayed Auto-reclosing:This is suitable for highly interconnected systems where the loss of a single line is unlikely to cause two sections of the system to drift apart and loose synchronism.

For EHV Systems:a) Choice of Dead Time:Lower limit is decided by deionising time of circuit breaker. 25

Upper limit is decided by transient stability and synchronism. Long transmission lines require longer dead time for single phase faults. The dead time for high speed auto-reclosing scheme with EHV system is 0.3-0.8 Sec. b) Choice for reclaim time:This should not be set to such a low value that the operating cycle of breaker is exceeded when two fault incident occurs close together. The reclaim time will be in the range of 10-30 Sec., depending on the breaker opening and closing mechanisms.

26

Z1

TRIP RELAY

ZL Z3 t3 t2 t1 A Z2 Z3 Z1 B C Z1 Z2 D t1 t2 t3

T2 T3 CR Z2 Z3 Z2 T2 TIMERS T3

CA RRIER SEND

Z1

C A R R IE R S E N D = Z1 T R IP = Z 1 + Z 2 * (C R + T 2 ) + Z 3 *T 3

Z2 Z3 CR

T2 T3

TRIP

OR AND

27

vi)

Carrier Communication Schemes:The main disadvantage of conventional time-stepped distance protection is that the instantaneous Zone-1 of the protective scheme at each end of the protected line is set to cover 80% of the line and hence faults in the balance 20% of the line (at each end) are cleared in Zone-2 time, which is undesirable. The desirable scheme is the one wherein the relays clear the faults on the 100% of the protected line instantaneously and also provide backup for uncleared faults on adjacent lines. This can be achieved by interconnecting the distance relays are each end of the line by a signaling channel (which can be either pilots, a power line carrier communication channel, a radio link or a microwave channel). The purpose of the signaling channel is to transmit the information about the system conditions at one end of the protected line to the other end and initiate or prevent tripping of the remote circuit breaker. The former arrangement is referred to as a Transfer trip scheme while the latter is known as Blocking scheme a) Transfer trip scheme:In this scheme, the distance relay at one end of the protected lines sends a carrier signal to the relay at other end of the line for inter-tripping, thereby clearing the faults on entire line instantaneously.

28

Z1 T2

CR

TRIP RELAY

ZL t3 t2 t1
A Z2D Z 3D Z3A Z 2A Z1A B Z 1D D

T3

Z2

T2 TIMERS T3

t1 t2 t3

Z3

CA RRIER SEND

Z1 Z2 Z3
T2 T3

TRIP

CARRIER SEND =Z1 TRIP =Z1*CR + Z2*T2 + Z3*T3

CR AND

OR

29

Transfer trip is of two types:i) Under-reaching scheme:The scheme in which the Zone-1 relay (set to cover about 80% of ZL) is used to send a signal to the remote end of the feeder for inter-tripping is termed as transfer trip under-reaching scheme. To avoid mal-operation due to receipt of false signal, the receiving end relay operation is inter-locked with its Zone3/starter operation i.e. the scheme operates either by its own Zone-1 relay operation or by receipt of carried and its Zone-3/starter operation. ii) Over-reaching scheme:This scheme is suitable for short lines where an underreaching Zone-1 would be too short to be of any practical use. In this scheme the relay set to reach beyond 100% of the line, is used to send an inter-tripping signal to the remote end of the line. It is essential that the receive relay contact be monitored by a directional relay to ensure that tripping does not take place unless the fault is within the protected section. The disadvantage of this scheme is that there is no independent Zone-1 tripping. The fast tripping therefore relies entirely on signaling channel. The disadvantages of these schemes is that the signal is transmitted over the fault line section. Distortion of the signal may occur due to attenuation introduced into the line by the fault. 30

ZL

Z1

TRIP RELAY

ZR

Z3 t3 t2 t1 A Z2 Z3 Z1 B C Z1 Z2 D t1 t2 t3

T2 T3 CR Z2 Z3 Z2 T2 TIMERS T3

ZR

CA RRIER SEND

Z1

C A R R IE R S E N D

= ZR

Z2 Z3 CR

T2 T3

TRIP

T R IP = Z 1 + Z 2 * ( C R * T o + T 2 ) + Z 3 *T 3

OR AN D

31

b)

Blocking schemes:In this scheme, a blocking signal is sent by the reverse looking directional unit ZR to prevent instantaneous tripping for Zone-2 & Zone-3 faults, external to the protected line. Here ZR must operate faster then forward looking Zone-3 units and the signaling channel must also be extremely fast is operation. Though all the distance schemes with carrier inter-tripping/carrier blocking facility are procured, the same are yet to be commissioned.

32

33

Factors affecting distance relay operation:i) Fault resistance. ii) Infeed effect. iii) Branching-off effect. iv) Load encroachment. i) Fault resistance:Fault resistance has two components:a) Arc resistance. b) Ground resistance. In a fault between phases, only arc resistance is involved. For a fault at F, the actual line impedance = R + JX = ZL Due to the presence of fault resistance, the impedance measured by the relay = R + JX + RF = ZR (where ZR > ZL) Fault arc resistance is given by Warrington's formula: Rarc = 8750 xl / I 1.4 where l = length of arc in ft I = fault current in Amps 34

35

The arc resistance has little effect on accuracy of zone-1 unit as it operates instanteously before the arc can stretch appreciably except in case of short lines. Reactance relays are therefore used for short lines where the fault resistance may be comparable with that of the protected lines and also for ground faults where the ground resistance is high. The arc resistance will have greater impact on accuracy of backup zones (time delayed) as the arc stretches appreciably. ii) Infeed effect:The effect of intermediate current source between relay location and fault point is termed as infeed effect. Consider the sketch indicated in fig --A fault at F on the line BC is at a distance of Z1+Z2 for the relay at station A. But when current I2 flows from bus D, the impedance to the fault as seen by the relay at A is Z1 + Z2 + Z2 x (I2/I1). Thus the fault is seen by the relay as farther than what it really is, i.e. distance relay under reaches due to the infeed effect. The effect of infeed becomes more pronounced with more interconnections at station B. 36

37

iii)

Branching-off effect: Consider the sketch indicated in fig --A fault at F is at the distance of Z1+Z2 for the relay at station A. But when current I1 gets distributed as I2 & I3 at station B, the impedance to fault seen by the relay at station A will be (Z1 + I3/I1 * Z2) which is less than (Z1+Z2). Then the fault is seen by the relay as nearer than what it really is i.e. distance relay overreaches due to branching-off effect. This overreaching tendency will cause the relay to loose its selectivity.

iv)

Load encroachment: While protecting long lines the necessary reach may be so large that the minimum service impedance (or load impedance) falls within the region of the starter. This would result in tripping without there being any fault. The two conditions i.e. operation at heavy load and short circuit differ by virtue of phase angle between voltage and current. For the load impedance, the phase angle will be within +30 to -30 Deg. While during short circuits, the fault impedance has a phase angle of 60 to 80 deg. (i.e. line angle). Load encroachment problem is more pronounced in case of under impedance starters and gets lessened in case of mho, elliptical, lens etc, type of starters. Relays with suitable characteristic on R-X diagram have to be carefully chosen to protect long and heavily loaded lines, and this becomes easily possible with microprocessor based numerical relays.

38

39

Non-switched scheme vs switched scheme: In an ideal Non-switched scheme, there will be 6 starters, 3 for phase faults and 3 for ground faults. There will be independent measuring units for both phase faults and earth fault for each phase, for all three zones, totaling to 18 units. This scheme is faster and more accurate but is costly. In the switched scheme, only one measuring unit will be used for all types of faults. This single measuring unit is switched to the correct fault loop impedance by switching-in the respective voltages and currents by the starter. The reach of the measuring element gets extended to zone-2 and zone-3 after the elapse of corresponding timings through zone extension process. Switched scheme is relatively slow in operation and has the risk of total scheme failure in the event of failure of the only one measuring unit available. Zone extension schemes: As a via media between non-switched and switched schemes, there are schemes with zone extension facility (such as EE make MM3V & MR3V relays). These schemes consists of 3 measuring units for phase faults and 3 measuring units for earth faults (apart from 3 starters).

40

Details of distance relays:41

1) i)

Make: MM3V: -

GEC Alstom Ltd. It is an electromagnetic type distance relay with: 3-mho measuring units for phase to phase faults. 3-mho measuring units for phase to earth faults. 3-mho starting units, each starter being associated with one phase and operating for all faults associated with that phase and one offset mho unit for power swing blocking.

R-X diagram is indicated Setting range in ohms for Zone-1 -------------------------------------0.834 to 30 1.335 to 48 1.668 to 60 Z2 = 1 to 3.5 times Z1 Z3 = 1 to 5 times Z1 --------------------------------------Some of the schemes are provided with a Zone-4 timer to make the scheme works as a 4 zone relay, the starter itself being the 4th zone. ii) MR3V: 42

It is an electromagnetic relays with 3 mho units for phase faults, 3 reactance units for earth faults. 3 mho starters, each being associated with one phase for all types of faults and one offset mho unit for power swing blocking. Setting ranges same as in MM3V. R-X diagram for phase faults is same as that for MM3V relay and for earth faults it is indicated in figure

iii)

RR3V: -_ 43

It is an electromagnetic relay with 3 Nos. reactance units for phase faults, 3 reactance units for earth faults, and 3 mho starters per phase for all types of faults and one offset mho unit for PSB. R-X diagram is indicated in figure iv) SSRR3V: It is an electromagnetic switched scheme with two version i.e. with mho or under impedance starter and available in low and high range.

44

45

3 under impedance starters directionalised by mho element or 3 mho element starters and for all types of fault, one reactance-measuring unit for phase and earth faults. Low range relay: Z1 = 0.5 to 7.7. Ohms (k1 of zone1: 7.7, 3.0, 1.22) High range relay: Z1 = 1.3 to 20 Ohms (k1 of zone-1: 20, 7.8, 3.16) Z2 = (1 to 3.5) times Z1 Z3 = (1 to 5) times Z1 R-X diagram is same as that for RR3V relay. Few versions do not have separate zone-4 timer. In such relays, zone-4 time = zone-3 time + 150 msec (fixed built-in delay). v) SHPM (Quadra mho): It is a non-switched static scheme with 18 measuring mho units. The zone-3 measuring elements will act as starters, which have either mho or a lenticular characteristic. The operating characteristic on R-X diagram is indicated in figure The lenticular characteristics allows healthy overloads and hence prevents tripping on load encroachment. Setting range: - 0.2 to 240 Ohms. It has built-in feature of continuous self monitoring (on demand and periodic self testing). All the additional features provided by relay can be enabled or disabled with the help of switches provided for them. 46

47

vi)

PYTS: It is a static switched scheme with modular plug-in construction (with built in test points). It has 3 under impedance starters and a single mho measuring unit. One U/I unit for power swing blocking. R-X diagram is indicated in figure Setting range: 0.05 to 40 Ohms, with starter having range of 20 to 70 Ohms. It has an uncompensated U/I starter, which has become a problem due to load encroachment for long lines. The V-I characteristic of the starter is indicated in above figure. When the voltage is less than 65% rated, the starter operates at a current greater than 0.25 In. With low voltages at some of the stations, this feature has caused relay to operate unnecessarily.

48

49

vii)

OPTIMHO

Optimho distance relay is a non-switched protection scheme having 18 comparators and upto five zones of protection (three basic zones of measurement and two for zone extension schemes) The relay has partially cross polarised shaped mho characteristics for zone-1 and zone2 phase units. The zone-3 for phase faults have offset lenticular characteristics which permit the relay to be applied to long heavily loaded transmission lines without encroachment into the load impedance. For earth faults, zone-1 and zone-2 units have quadrilateral characteristics with independent reaches in resistive and reactive axes. The zone-3 units are offset quadrilateral. The zone-3 units for phase and earth faults can be chosen for offset or to see in reverse direction. The relay characteristic is indicated in Fig. On event of failure of quadrilateral comparators, mho/lenticular comparators are automatically enabled but vice versa is not possible. The relay has self testing facility. It has 8 groups of settings and any one group can be set active.

50

51

PD 521: a) b) c) d) e) It is a numerical protection relay with polygon characteristics. It consists of four impedance zones with independent R and X values for each zone Zone 4 can be utilized as a special zone for cabie protection. R X diagram as indicated in figure. Through MMI, one can enter and edit the settings (The settings are password protected) Setting Range Timers : : 0.1 to 2000 Ohms. 0 to 10 Secs.

52

Zone-3 Zone-P(programmable) Zone-2 Zone-1X R2 Zone-1 R1ph

Rp R4ph R3

53

Zone-4

MICOM DISTANCE RELAY (Alstom make): MICOM P440 series is a distance scheme with advanced numerical technology. MICOM P441 and P442 relays have five zones of phase fault protection and five zones of earth fault protection. a) Phase fault protection Phase fault quadrilateral characteristics is shown in the figure. i) Zones 1,2 & 3 directional forward zones, as used in conventional three zone distance schemes. Note that Zone-1 can be extended to Zone-1X when required in Zone-1 extension scheme. Zone P Programmable. Selectable as a directional forward or reverse zone. Zone-4 Directional reverse zone. Note that Zone-3 and Zone-4 can be set together to give effectively a forward zone with a reverse offset.

ii) iii)

54

Zone-3 Zone-P(programmable) Zone-2 Zone-1X R2 R1G Zone-1 Zone-4

Rp R3 R4G

55

a) Earth Fault Protection: Earth fault quadrilateral characteristics is similar to the phase fault quadrilateral characteristics as shown below. Resistive reaches can be set independently for phase and earth fault protections. All earth fault elements are quadrilateral shaped, and are directionalised similar to the phase fault elements. The impedance reaches of earth fault elements use residual compensation of the corresponding phase fault reaches.

56

57

2)

Make: - BBC/HBB i) LZ96: It is a non-switched scheme with 3 underimpedance measuring units common for ground and 3-phase faults. 3 Nos. under impedance (offset mho) starters, one under-impedance unit for all possible phase to phase faults. R-X diagram is indicated in figure Forward and reverse reach can be selected independently in starters (with zone-4 time setting). Setting range: 0.1 to 100 Ohms. ii) LIZ6: It is a switched scheme with 3 under-impedance starters, 3 overcurrent starters and one neutral current starter. It has one reactance measuring unit for all faults. With the provision of angle replica unit the relay has special operating characteristic on R-X diagram indicated in figure, which permits high loading on long lines. This being the initial versions of static relays there have been number of component failure and are being phased out.

58

iii) a)

L3 relays: L3WYS: This relay consists of 3 under impedance starters and a single directional reactance measuring unit (CM relay). It is four zone relay, the zone-4, starter step being non-directional. Time settings for all the four zones (including Zone-1) can be varied from 0.1 to 5 seconds. R-X diagram is indicated in figure.

59

b)

L3wyas: This is similar to L3WYS relay except that the U/I starters are provided with compounding chokes thereby shifting the circle, making it an offset mho as indicated in figures.

It is also supplemented by Yi/L - power swing blocking unit. iv) L6ft: It is high speed, single step distance relay usually supplemented to L3wyas or L3wys. It is set to protect 80% of line and without any time delay.

60

61

v)

Yke/l relay: This consists of three under impedance starters, used in conjunction with L3wyas relays. By provision of compounding chokes, the operating region of the Yke/l relay is shifted much above the origin of the R-X diagram. The operating characteristic of the combination of L3wyas and Yke/l relay is indicated in figure. It may be seen from the diagram that this combination permits much higher loading and protects longer lines, without any problem of load encroachment.

62

63

3) Make: ABB: i) RYZFC: It has come into service in the initial stage of the advent of static relays, has 3 mho measuring units for earth faults, one mho unit for phase faults and 3 under impedance starters. In addition, this relay has negative sequence current starter with a fixed setting of 20% of In, which causes the relay to trip in Zone-4. The starter can be made to operate either as a circle or as oval. R-X diagram is indicated in figure. Setting range: - 1.8 to 200 Ohms. a) b) This relay is found to lose its directional sensitivity for closeby reverse faults and hence not recommended for use on feeders emanating from generating stations. Also the negative phase sequence starter is found to respond to very far end faults.

ii) RAZOG: It is a switched scheme with 3 under impedance starters and one reactance measuring unit. It has quadrilateral characteristic. R-X diagram is indicated in figure. Setting range: 0.25 to 64 Ohms. The starter can be made to operate either as a circle or oval. 64

65

iii)

RAZFE: It is static three zone non-switched scheme. For ground and 3-phase faults, the distance relay has a reactance like operating characteristic, the reactance line being inclined by a few degrees towards resistance axis on R-X diagram, which provides excellent margin for high resistance faults and minimises effects of load current and remote ends infeed on distance measurement RX diagram is indicated below. To avoid load encroachment problem, the relay is provided with blinder, which has independent settings in resistive and reactive directions. For phase to phase faults, mho units are used. Setting rage: 0.25 to 64 Ohms.

66

67

iv)

RAZOA: It is a static scheme having 3 under -impedance starters and one measuring unit. The directional measuring unit has got quadrilateral characteristic with independent settings in resistive and reactive directions. R-X diagram is as indicated.

The U/I starter can be made to operate with a circle or oval characteristic with a selectable switch (S3: 1 ON for circle OFF for oval in RGZB module). RGSB Module: Directional Non-directional Setting range : S1: 1 - OFF : S1: 1 - ON : 0.16 to 64 Ohms.

68

69

(v)

RELZ-100: It is a numerical relay with quadrilateral impedance units for phase and earth faults. Each measuring unit has individual and independent setting of the reach in resistive and reactive directions, as well as for the zero sequence compensation factor, KN. Entire Zone-3 reach (in forward direction) is available in reverse direction with a separate timer T3R. R-X diagram is as indicated Four groups of setting parameters are possible to suit different system conditions. Only one of the groups will be in service by choice. It has continuous self monitoring and self testing feature and indicate the same by extinguishing "Relay Available" LED on the relay. Through MMI, one can enter; edit the settings, read the mean service values of line voltage, current, real, reactive power and frequency. It stores data of latest 3 disturbances occurred. (The settings are not password protected). Setting rage: Timers: 0.1 to 150 Ohms. 0 to 10 Secs.

It has a feature which does overload supervision and unsymmetrical load condition, which can be used for alarm or trip.

70

71

vi)

RADSL: This pilot wire protection scheme used for protection of short lines. It is very fast operating relay, clearing the faults in 100% of line without any time delay. This is commissioned on 220 KV KTS 'C' Station - KTS V Stage tie lines 1 & 2 at both ends as Main-1 protection scheme (Main-II being RELZ-100 relay). Likewise GEC make FAC34 pilot wire differential relays are provided on 220 KV NTPC - RAMAGUNDAM tie lines 1 & 2 with backup O/L, E/L relays. Make: - Universal Electric i) MDT45B: It is a non-switched 3-zone distance scheme with 18 measuring units, 3 Nos. low set starters ZL and 3 Nos. high set starters ZH. It is available in two ranges low and high. R-X diagram is indicated in figure. a) b) For Low range: Reactance Measuring units for Zone-1 & Zone-2. For High range: Mho measuring units for Zone-1 & Zone-2.

4)

72

73

ii)

MDTB101: It is switched scheme, with 3 impedance starters, one neutral overcurrent starter and one mho measuring unit. R-X diagram is indicated in figure. This relay has a V-I characteristic similar to that of PYTS relay. When the voltage is less than 65% rated, the starter operates at a current greater than 0.25 In. For 220 KV lines, the settings on Main-I distance relay must be on par with that of Main-II relay and vice-versa. For 132 KV lines, distance relay along with directional O/L, E/L relays are used. The operating time of O/L, E/L relays for adjacent bus faults are set equal to or more than zone-2 time of distance relay.

74

75

5)

Make: - Easun Reyrolle: i) THR4PE24: It is static non-switched scheme with 3 forward zones and 1 reverse zone consists of a total of 24 measuring units. 12 Nos. mho units for zone-1 & zone-2 for phase and earth faults. 6 Nos. offset mho units for zone-3, 6 Nos. Mho units for reverse reach. R-X diagram is indicated in figure. It has reverse reach set to (c x zone-1) for phase faults and (c x zone-1) (1+KN) for earth faults, KN being compensation factor. Generally c is set equal to '1'. ii) THR4PE1: It is static switched scheme with 3 offset mho starters and one mho measuring unit. R-X diagram is indicated in the figure. It is available in low and high ranges: Setting range: Low range: - 0.08 to 9.5 Ohms (with A:0.8 to 9.6) High range: - 0.4 to 47.5 Ohms (with A: 4 to 48) The starter has a built in reverse reach, equal to 50% of forward reach for phase faults and 50% of forward reach (1+KN) for earth faults, KN being compensation factor.

76

77

Make: - Seimens Ltd. 7SA511 relay: It is a numerical protection scheme with 16 bit microprocessor. With three version of detectors. i) Phase selective overcurrent fault detector. ii) Voltage controlled (under-impedance) fault detector (with independent R & X reaches) and iii) Polygonally shaped angle-dependent impedance fault detector. It has five zones (two of which can be used for communication schemes). R-X diagram is indicated below. Apart from common features, it provides Emergency overcurrent function, which comes into picture when main distance scheme is blocked due to VT fuse failure conditions. It provides two user defined logic functions. It has continuous self monitoring and self testing feature. It stores data of latest three faults and measures values of load current, operating voltage, power and frequency continuously. Setting range: 0.1 to 200 Ohms with 0.0 to 32 sec (in step of 0.01 sec) timers. Four groups of settings are possible to suit different system conditions. Only one of the groups will be in service by choice. 78

79

SEL 321: - It is numerical relay with a) Four Mho zones for phase faults with independent phase to phase overcurrent supervision. b) Four ground faults for Mho and Quadrilateral zones with independent phase and residual overcurrent supervision and zero sequence compensation. c) Two Quadrilateral zones for power swing blocking. d) Load-encroachment characteristics. e) Instantaneous, Definite time and IDMT overcurrent characteristics. f) Six (6) setting groups are available in the scheme. Setting ranges:For Mho zones For Quadrilateral Zones Reactance Resistance Timers 80 : : : : : 0.25 to 320 Ohms (Secondary) 0.25 to 250 Ohms (Secondary) 0-2000 Cycles 0.25 to 320 Ohms (Secondary)

Relay indications: purpose and meaning: The relay indications are a guide to identify the type and broad location of fault. They are the means to assess the relay performance by tallying with the actual faults occurred. They help in review and analysis of the trippings occurred. Different manufacturers used different symbols/flags of signaling different types of faults. Whenever the relays operate, their indications should be noted before they are reset Relay indications with their meanings on various types and makes of relays are indicated in the following tables.

81

CHART SHOWING RELAY INDICATIONS FOR VARIOUS RELAYS

S.No Make & Type Distance protection of Relay
operated Trip.

Type of Fault with Indications

Zone Indication

Switch On-to Fault Trip Z4

Power Carrier Swing Relay Blockin Operated g

V.T Fuse Failure

Type Indica-tions Type Indica Phase to Phase to -tions phase Earth

Z1

Z2

Z3

1.

EE/GEC MM3V

R-Y Y-B B-R R-Y Y-B B-R R-Y-B R-Y Y-B B-R R-Y Y-B B-R R-Y Y-B B-R R-Y Y-B B-R R-Y-B

30(A-B) 30(B-C) 30(C-A) AB

R-E Y-E B-E R-E

30A 30B 30C AN BN CN 30A 30B 30C 30A 30B 30C 30D 30E 30F A B C 30G 30G Z1

30G 30H Z2

30G 30H 30J Z3

2/21

85X

Tripping Blocked

2.

MM3T

Tripping Blocked

3.

RR3V

BC Y-E CA B-E AB,BC,CA 30(A-B) R-E 30(B-C) 30(C-A) 30(A-B) 30(B-C) 30(C-A) 30A 30B 30C A,B B,C C,A A,B,C Y-E B-E R-E Y-E B-E R-E Y-E B-E R-E Y-E B-E

30G 30H

30G 30H 30J 30G 30H 30J 30G 30H 30J

Z1,Z3

Tripping Blocked

2/21

4.

MR3V

30G

30G 30H 30G 30H

2/21
Tripping Blocked

5.

MR3V

30G

6.

SSRR3V

Z1

Z1,Z2

2/21

CHART SHOWING RELAY INDICATIONS FOR VARIOUS RELAYS 82

S.No

Make & Type of Relay

Distance protection operated Trip.

Type of Fault with Indications

Zone Indication

Switch Power On-to Swing Fault Trip Blocking Z4 Z4

Carrier Relay Operated

V.T Fuse Failure

Type Ph to ph

Indications

Type Ph to E

Indications

Z1

Z2 Z2

Z3 Z3

7.

EE/GEC PYTS

R-Y Y-B B-R R-Y-B

A,B B,C C,A A,B,C A,B B,C C,A A,B,C R,S S,T T,R R,S,T R,S S,T T,R R,S,T

R-E Y-E B-E R-E Y-E B-E R-E Y-E B-E R-E Y-E B-E

A B C A B C R S T R,E S,E T,E

SOTF

PSB

8.

SHPM QUADR OMHO

R-Y Y-B B-R R-Y-B

Z2

Z3

SOTF

AIDED VTRIP FAIL

9.

LZ-96

R-Y Y-B B-R R-Y-B R-Y Y-B B-R R-Y-B

2 T2

HF (Yellow)

10.

LIZ-6

T2, T3 T2,T
3T4

CHART SHOWING RELAY INDICATIONS FOR VARIOUS RELAYS

S.No Make &
Distance

Type of Fault with Indications

Zone Indication

Switch

Power

Carrier

V.T

83

Type of Relay

protection operated Trip. Type Ph to Ph Indications Type Ph to E Indications Z1 Z2 Z3 Z4

On-to Fault Trip

Swing Relay Blocking Operated

Fuse Failure

11.

L3wyas/ L3wys/ Lz3

PD (D)

R-Y

PAR(R) , PAS(S) PAS(S) PAT(T) PAT(T) PAR(R)

R-E

PAR(R) PE(E)

PSII (2)

PSII
PS-III (2) (3)

PSII
PS-III (2) (3)

PTa

PtrH

Y-B B-R 12. 13. L6FT ASEA / ABB :RYZFC PD3 UD R-Y Y-B B-R R-Y-B R-Y Y-B B-R R-Y-B R-Y } Y-B } B-R } R-Y-B

Y-E B-E

PAS(S) PE(E) PAT(T) PE(E) PTa5

14.

RAZOG

UD

R,S S,T T,R R,S,T R,S S,T T,R R,S,T 2-phase 3-Phase

R-E Y-E B-E R-E Y-E B-E R-E Y-E B-E

R S T R S T RN SN TN Z1 Z2

2,3

2,3,4

CS/CR

2,3

15.

RAZFE

Z2, TK2

TK2, TK3

CHART SHOWING RELAY INDICATIONS FOR VARIOUS RELAYS

S.No Make &
Distance

Type of Fault with Indications

Zone Indication

Switch

Power

Carrier

V.T Fuse

84

Type of Relay

protection operated Trip. Type Ph to ph Indications Type Ph to E Indications Z1 Z2 Z3 Z4

On-to Fault Trip

Swing
Blocking

Relay Operated

Failure

16.

ASEA/ ABB RAZOA

Trip

17.

REL-100

Trip Z

R-Y Y-B B-R R-Y-B R-Y Y-B B-R R-Y-B

R,S S,T T,R R,S,T PSR,PSS PSS,PST PST,PSR PSR,PSS PST AB,ZIS BC,ZIS CA,ZIS ABC,ZIS AB BC CA ABC r, y y, b b, r r, y, b

R-E Y-E B-E R-E Y-E B-E

R,N S,N T,N

PSR,PSN (Trip-R) PSS,PSN (Trip-S) PST,PSN (Trip-T) TRZ1

2,3

2,3,4

TRZ2

TRZ3

TRZ3R

Zm1, Zm2, Zm3 Z1

Zm2, Zm3 Zm3

Zm3R
(Reve rse)

TREF SOTF

PSB

CRZ/CBZ VTF / VTS

18.

UE
MDT-45B

19

UE
MDTB-101

20.

ER
THR4PE24

PO

R-Y Y-B B-R R-Y-B R-Y Y-B B-R R-Y-B R-Y Y-B B-R R-Y-B

R-E Y-E B-E R-E Y-E B-E R-E Y-E B-E

A B C A B C r y b

Z2

Z3

Z4

SOFT

PSB

RR/CS

SV

Z2

Z3

Z4

SOFT

CAT

VTF

Pt 1 2 3

CHART SHOWING RELAY INDICATIONS FOR VARIOUS RELAYS

S. Make &
Distance

Type of Fault with Indications

Zone Indication

Switch

Power

Carrier V.T Fuse

85

Type of Relay

protn. operated Trip. Type Ph to ph Indications Type Ph to E Indications Z1 Z2 Z3 Z4

On-to Fault Trip

Swing
Blocking

Relay Optd

Failure

THR4PE1

PO

SIEMENS

R-Y Y-B B-R R-Y-B R-Y Y-B B-R R-Y-B R-Y Y-B B-R R-Y-B

r, y y, b b, r r, y, b
JR,JS,R,S JS,JT,S,T JT,JR,T,R JR,JS,JT, R,S,T LED 2,3, 12,13 LED 3,4, 13,14 LED 4,2, 14,12 LED 2,3, 4,12,13,14

R-E Y-E B-E R-E Y-E B-E R-E Y-E B-E

r, Earth y, Earth b, Earth

JR,TM, R,M JS,JM,S,M JT,JM,T,M

2&3

T2

T3

T4

RIZ-24a

75A511

LED 2,5,12 LED 3,5,13 LED 4,5,14

LED 7

LED 8

LED 9

LED 10

AR

IGE:a) GCY51A b) GCX51A

R-Y Y-B B-R

R,Y Y,B B,R R-E Y-E B-E R Y B

II

III

Distance relays in service in A.P.System: -----------------------------------------------------------------------------------------86

S.No. Make

Main-I distance Main-II relay relay -----------------------------------------------------------------------------------------1. GEC Alstom/ MM3V MR3V EE SSRR3V (MHO/UI starter) RR3V SHPM PYTS OPTIMHO EPAC PD521 MICOM MICOM 2. ABB/ASEA RYZFC RAZFE RELZ-100 REL511 REL521 REL316 RADSL LZ96 L3wyas+L6ft L3wys+L6ft 7SA511 RAZOG | | RAZOA

3. 4.

BBC/HBB SEIMENS

LIZ6 7SA511 RIZ24a 87

5.

ER

THR4PE24 SEL-321

THR4PE1

6. UE MDT45B MDTB101 ----------------------------------------------------------------------------------------

88

89

90

91

92