Grey Matter – www.usegreymatter.

com
8648 – DESIGNED AND PRODUCED BY

Regional Headquarters
Americas
8296 Sherwick Court,
Jessup, MD 20794,
United States
T: +1 (301) 490 8427
E: cclus@cclint.com

Europe
Unit 8, Millennium Drive,
Leeds, LS11 5BP,
United Kingdom
T: +44 (0) 113 270 1221
E: cclgb@cclint.com

Gulf
Detroit House Building, Flat No. 201,
Motorcity, Dubai,
United Arab Emirates
T: +971 (4) 454 23 42

POST-TENSIONING
E: cclgulf@cclint.com
F: +971 (4) 454 23 43

MENA/Africa

SYSTEMS
Derviche Haddad Building,
Zouk Mosbeh, Beirut,
Lebanon
T: +961 (09) 22 60 44
E: cclsg@cclint.com
F: +961 (09) 22 60 77

XM SYSTEM

The specifications, information and performance of the products

manufactured by CCL and featured in this publication are presented
in good faith and believed to be correct. Details may be changed without
notice. CCL makes no representations or warranties as
to the completeness or accuracy of the information. Information
is supplied upon the condition that the persons receiving same
will make their own determination as to its suitability for their
purposes prior to use. In no event will CCL be responsible for damages
of any nature whatsoever resulting from the use of, or reliance upon,
information contained in this document. CCL accepts no liability for
any errors or omissions therein.

CCL.12/2017

www.cclint.com www.cclint.com
 POST-TENSIONING SYSTEMS

XM SYSTEM
XM SYSTEM - 13 MM AND 15 MM TENDONS

No. of Strands D
Anchorage A B* ØC ØDuct** ØE L G H ØM
13/15 mm 13/15 mm
LIVE END XM-10 4/3 234 70 48 55/60 40/45 95 160 95 29 130
D A
XM-20 6/4 300 70 50 55/60 40/45 105 170 105 29 140
L
XM-30 9/7 362 100 64 70/75 43/48 130 228 130 29 168

Wedge XM-35 12/9 493 113 74 80/85 48/47 155 270 155 29 210
XM-40 18/12 629 113 74 80/85 62/54 180 275 180 29 236
B
XM-45 19/13 629 113 74 80/85 67/63 180 275 180 29 236
XM-50 22/15 693 130 84 90/95 69/60 195 310 195 29 253
ØC
ØE XM-55 25/17 742 150 98 100/105 67/62 215 330 215 29 270
XM-60 27/19 749 150 98 100/105 76/76 220 337 220 29 280
XM-70 31/22 913 150 98 100/105 74/70 245 370 245 29 325
XM-75 37/25 1001 175 113 115/120 80/80 265 418 265 29 335
XM-80 40/27 1001 175 113 115/120 84/83 270 418 270 29 350
Force Transfer Unit Deviation Cone Duct Coupler Duct
XM-90 46/31 1118 190 123 125/130 87/94 295 440 295 29 378
Anchor Head
XM-95 51/35 1079 210 138 140/145 97/94 305 480 305 29 396
XM-100 55/37 1089 210 138 140/145 98/102 310 490 310 29 396
NON-ACCESSIBLE DEAD END
All dimensions in mm.
H D A *B is the dimension for the straight part of the deviation cone that links to the duct through a duct coupler.
**Duct dimensions shown are for inside/outside diameter of metal ducts.
L Plastic duct dimensions are shown in the Post-Tensioning Systems Civil Engineering brochure.

ØC
ØE G

ØM

Spring Plate Wedge Anchor Head Force Transfer Unit Deviation Cone Duct Coupler Duct
MG JACK DIMENSIONS
BURIED DEAD END
H D A S

L
H
S**
B Jack Size A B* ØC ØD ØJ ØG Non- Weight
ARI min
ARI

1800MG 388 210 232 342 426 260 342 322 760 275 kg
ØC
ØE G 3000MG 388 200 270 405 500 280 305 290 700 350 kg
ØC ØD ØJ 4000MG 415 210 360 490 585 344 327 307 730 575 kg

ØG 6000MG 462 209 410 576 680 400 334 304 766 700 kg
7500MG 480 220 490 652 760 478 343 321 850 1150 kg
All dimensions in mm.
* Elongation stroke of jack.
** Minimum length of strand.
Spring Plate Wedge Anchor Head Force Transfer Unit Deviation Cone Duct Coupler Duct
H A B

CRITICAL DIMENSIONS
F
M

40 L ØN

D
D C
B
ØK

E
C A
D **Pocket dimensions accommodate grout caps (steel non-encapsulating/plastic
*B Based on 25 mm cover. encapsulating) and jack clearance for stressing. In some edge conditions for
B Smaller centre-centre dimensions can be achieved. C36/46 concrete, where edge distance B is smaller than pocket dimensions
Contact CCL for advice. C and D, the pocket cannot be accommodated.

Anchor Centre-Centre and Edge Distances Pocket Dimensions** Jack Dimensions Helical Reinforcement Dimensions, fyk = 500 MPa

No. of Concrete Strength at Transfer (MPa) Grout Cap: Concrete Strength at Transfer (MPa)
Jack Size Anchorage Strands Non-encapsulating / H
13 /15 mm C25/30 C36/46 Plastic Encapsulating C25/30 C36/46
C Fo ØG ØJ

A B* A B* D E Non-Auto-release ØK L M ØN ØK L M ØN
Auto-release Innards
Innards
XM-10 4/3 245 140 200 115 120 130 120 5 260 342 322 426 195 40 245 10 160 55 200 8
1800MG XM-20 6/4 285 160 220 125 120 130 120 5 260 342 322 426 235 45 285 10 170 50 220 10
XM-30 9/7 340 185 260 145 120 135 125 5 260 342 322 426 290 40 340 12 230 40 260 10
XM-30 9/7 340 185 260 145 135 150 125 5 280 305 290 500 290 40 340 12 230 40 260 10
XM-35 12/9 385 210 300 165 135 150/170 125/180 5 280 305 290 500 335 40 385 12 250 45 300 12
3000MG
XM-40 18/12 440 235 320 175 135 150/175 140/210 5 280 305 290 500 390 40 440 12 290 45 320 12
XM-45 19/13 465 250 340 185 135 150/175 145/210 5 280 305 290 500 415 40 465 12 300 50 340 16
XM-40 18/12 440 235 320 175 170 185/210 140/210 5 344 327 307 585 390 40 440 12 290 45 320 12
XM-45 19/13 465 250 340 185 170 185/210 145/210 5 344 327 307 585 415 40 465 12 300 50 340 16
4000MG XM-50 22/15 500 265 360 195 170 185/210 145/210 5 344 327 307 585 450 60 500 16 315 50 360 16
XM-55 25/17 525 280 380 205 170 185/210 145/215 5 344 327 307 585 475 55 525 16 340 50 380 16
XM-60 27/19 550 290 400 215 170 185/210 155/230 5 344 327 307 585 500 55 550 16 365 60 400 16
XM-50 22/15 500 265 360 195 205 220/245 145/210 5 400 334 304 680 450 60 500 16 315 50 360 16
XM-55 25/17 525 280 380 205 205 220/245 145/215 5 400 334 304 680 475 55 525 16 340 50 380 16
XM-60 27/19 550 290 400 215 205 220/245 155/230 5 400 334 304 680 500 55 550 16 365 60 400 16
6000MG
XM-70 31/22 600 315 430 230 205 220/245 150/230 5 400 334 304 680 540 55 600 16 385 60 430 16
XM-75 37/25 640 335 460 245 205 220/245 155/230 5 400 334 304 680 580 50 640 16 415 60 460 16
XM-80 40/27 665 350 480 255 205 220/250 160/240 5 400 334 304 680 605 70 665 20 445 65 480 16
XM-60 27/19 550 290 400 215 235 250/275 155/230 5 480 343 321 760 500 55 550 16 365 60 400 16
XM-70 31/22 600 315 430 230 235 250/275 150/230 5 480 343 321 760 540 55 600 16 385 60 430 16
XM-75 37/25 640 335 460 245 235 250/275 155/230 5 480 343 321 760 580 50 640 16 415 60 460 16
7500MG XM-80 40/27 665 350 480 255 235 250/280 160/240 5 480 343 321 760 605 70 665 20 445 65 480 16
XM-90 46/31 730 380 650 340 235 250/275 170/230 5 480 343 321 760 670 70 730 20 590 50 650 16
XM-95 51/35 760 395 680 355 235 250/280 175/255 5 480 343 321 760 690 65 760 20 610 45 680 16
XM-100 55/37 770 400 695 365 235 255/280 180/255 5 480 343 321 760 700 60 770 20 625 45 695 16

www.cclint.com