P1E492591

SIPROTEC 5 - Configuration 22.06.
2022 , 05:02:31 AM
________________________________________________________________________________________________
Device: 7SS85 Busbar Protection
2 zones, 4 bays incl., discIm
Product code
Short: P1E492591
Long: 7SS85DAAAAA00AAAA0AYB11113111BBAA000000AC0CC1BA1CB1CC1CC1CC1BC1CE0CE0E
A0
Technical Data:
Firmware: Current version

Binary inputs: 99
Binary outputs: 57 Relays (35 Standard, 22 Fast, 0 High-Speed, 0 Power)
Current transformers: 36 for protection
Voltage transformers: 4 standard
________________________________________________________________________________________________
1/6
SIPROTEC 5 - Configuration 22.06.2022 , 05:02:31 AM
________________________________________________________________________________________________
Measuring-transducer inputs: 0 (20 mA or 10 V, fast)

0 (20 mA, standard)
0 (temperature)
Housing width: 1 x 19'' + 2/3 x 19''
Housing type: Flush mounting
Modules in 19" row 1: IO203, PS201, IO202, IO203, IO203, IO203
Modules in 19" row 2: PS203, IO205, IO205, IO230
LEDs/Push-buttons: 16 LEDs
Operation Panel: Integrated
Key switch: Without
Display type: Large display
Front Design: Standard
Power Supply: DC 60 V-250 V, AC 100 V-230 V
Redundant Power Supply: No
Communication/Plug-in modules:
Communications encryption: Normal

Integrated Ethernet port J: for DIGSI 5
Plug-in module position E: ETH-BB-2FO: 2x optical Ethernet 100 Mbit/s, 1300 nm, duplex LC
connector
, 2 km over 50/125 um or 62.5/125 um multimode optical fiber
Communication Protocols: applicable for DIGSI 5, IEC 61850-8-1
MMS and
GOOSE, IEC 60870-5-104, DNP3 TCP, Modbus TCP,
Synchrophasor (IEEE
C37.118 - IP), Profinet IO, SUP, DHCP, SNTP, SNMP, etc.
Redundancy protocols: Line Mode, RSTP, HSR, PRP
Plug-in module position F: Port is available but not assembled
Functions:
Function points class: Base + 475 function points
Note on function-points class

The function-points class results from the sum of the function points of the selected functions. You can
apply these functions according to the selected function-points class. The device also allows each other
selection of functions if the sum of the required function points is within the selected function-points
class.
From Version V9.3 on the function-points class "1400+" is withdrawn. With this class function-points
exceeding the limit of 1400 were free of charge. The maximum function-points class is now 1400. If a
function-points budget of more than 1400 points is required for a device the application
Function-Point-Manager need to be applied. All function points are liable to cost.
In the engineering phase DIGSI 5 checks that the selected configuration is suitable (capable of running
in the device) before loading it to the device.
Miscellaneous:
________________________________________________________________________________________________
2/6
________________________________________________________________________________________________
Warranty: 5 years
Special Approvals: Without
Firmware: Current version
________________________________________________________________________________________________
3/6
________________________________________________________________________________________________
7SS85 Busbar Protection - Overview Function points calculation
(P1E492591)
Included Functions
ANSI Function Abbr. Included

Protection functions for 3-pole tripping 3-pole
Protection functions for 1-pole tripping 1-pole
Hardware quantity structure expandable I/O
Process Bus Client function (Note: This function requires a PB client

ETH-BD-2FO plug-in module)
IEEE 1588v2/PTP Grandmaster Clock (Note: This function GMC
requires a ETH-BD-2FO, with V9.20)
38 Temperature supervision θ>
50N/ 51N Overcurrent protection, ground IN>

TD
50BF Inherent circuit-breaker failure protection CBFP
74TC Trip-circuit supervision TCS
87B Busbar differential protection ΔI
86 Lockout
Broken-wire detection for differential protection
87 STUB Stub-fault differential protection (for breaker-and-a-half

scheme)
AFD Arc-protection (only with plug-in module ARC-CD-3FO) 10 X
Measured values - standard
Switching statistic counters
PQ-Basic measured values: THD (Total Harmonic

Distortion) and harmonics (from V8.01) THD voltage
aggregation values (from V8.40)
CFC (Standard, control)
Inrush current detection
External trip initiation
Control
________________________________________________________________________________________________
4/6
________________________________________________________________________________________________
Circuit-breaker
Disconnector/Grounding switch
Fault recording of analog and binary signals
Monitoring and supervision
Protection interface, serial
Temperature acquisition via communication protocol
Optional Functions
ANSI Function Abbr. Included Quantity Value Points

IEC 61850-9-2 Merging Unit MU 0 200 0
function (Note: Max. 2 streams
per MU function, each MU
function requires a
ETH-BD-2FO plug-in module)
21GT Impedance protection for Z< 0 130 0
transformers
27 Undervoltage protection: V< 0 5 0
"3-phase" or
"positive-sequence system V1"
or "universal Vx"
47 Overvoltage protection, V2> 0 5 0
negative-sequence system
50/51 Overcurrent protection, phases I> 0 30 0
TD
50BF Circuit-breaker failure CBFP 0 15 0
protection, 3-pole
50BF Circuit-breaker failure CBFP 0 25 0
protection, 1-/3-pole
50EF End-fault protection 0 5 0
59, 59N Overvoltage protection: V> 0 5 0
"3-phase" or "zero-sequence
system V0" or "universal Vx"
67 Directional overcurrent I>, ∠(V,I) 0 30 0
protection, phases
67N Directional overcurrent IN>, ∠(V,I) 0 30 0
protection, ground
81 Frequency protection: "f>" or f<>; df/dt<> 0 5 0
"f<" or "df/dt"
87B Bus coupler differential ΔI 0 50 0
protection
________________________________________________________________________________________________
5/6
________________________________________________________________________________________________
Bay 4X 0 50 0
Cross stabilization 0 250 0

PMU Synchrophasor measurement PMU 0 40 0
Measured values - extended: 0 3 0
Min, Max, Avg
PQ-Basic measured values: 0 20 0
Voltage unbalance (from
V8.40)
Voltage variations - voltage
dips, swells and interruptions
(from V8.40)
TDD - Total Demand Distortion
(from V8.40)
CFC arithmetic 0 40 0
Circuit-breaker wear ΣIx, I²t, 2P 0 10 0
monitoring
Switching sequences function 0 5 0
SSR Slow-scan recorder (from SSR 1X 0 40 0
V8.80)
Cyber Security: Role-Based 0 25 0

Access Control (from V7.8)
Cyber Security: IEEE 802.1x 0 10 0
based network authentication
(from V8.3)
Total: 0
________________________________________________________________________________________________
6/6

P1E492591

Uploaded by

Copyright:

Available Formats

P1E492591

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

P1E492591

Uploaded by

Copyright:

Available Formats

SIPROTEC 5 - Configuration 22.06.

Device: 7SS85 Busbar Protection

2 zones, 4 bays incl., discIm

Firmware: Current version

Measuring-transducer inputs: 0 (20 mA or 10 V, fast)

Communications encryption: Normal

Plug-in module position F: Port is available but not assembled

Function points class: Base + 475 function points

Note on function-points class

7SS85 Busbar Protection - Overview Function points calculation

ANSI Function Abbr. Included

Protection functions for 1-pole tripping 1-pole

Hardware quantity structure expandable I/O

Process Bus Client function (Note: This function requires a PB client

50N/ 51N Overcurrent protection, ground IN>

74TC Trip-circuit supervision TCS

87B Busbar differential protection ΔI

Broken-wire detection for differential protection

87 STUB Stub-fault differential protection (for breaker-and-a-half

Measured values - standard

Switching statistic counters

PQ-Basic measured values: THD (Total Harmonic

Inrush current detection

External trip initiation

Fault recording of analog and binary signals

Monitoring and supervision

Protection interface, serial

Temperature acquisition via communication protocol

ANSI Function Abbr. Included Quantity Value Points

Cross stabilization 0 250 0

Cyber Security: Role-Based 0 25 0

You might also like