Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

2008 Jeep Wrangler Unlimited X 2008 Jeep Wrangler Unlimited X

Download as pdf or txt
Download as pdf or txt
You are on page 1of 12

2008 Jeep Wrangler Unlimited X

2008 AUTOMATIC TRANSMISSION 42RLE - Electrical Diagnostics - Wrangler

P0870-OD HYDRAULIC PRESSURE TEST

Circuit Schematic

Fig. 64: Transmission Solenoid/Pressure Switch Assembly Circuit Schematic


Courtesy of CHRYSLER LLC

jueves, 3 de noviembre de 2022 12:44:52


12:44:48 p. m. Page 1 © 2011 Mitchell Repair Information Company, LLC.
2008 Jeep Wrangler Unlimited X
2008 AUTOMATIC TRANSMISSION 42RLE - Electrical Diagnostics - Wrangler

Additional Wiring

For complete wiring diagrams refer to SYSTEM WIRING DIAGRAMS article.

Pressure switches are normally off or open (no pressure applied) and read high (+12 volts). When an element is
applied, the corresponding pressure switch closes to ground (0 volts) or turns on. The controller tests the OD
and 2/4 pressure switches when they are off (when the corresponding friction element is not applied) by briefly
applying the OD and 2/4 elements which will cause the corresponding pressure switch to close. The test verifies
that the switches are operational and that the switch will close when the corresponding element is applied. If a
switch fails to respond, it is re-tested. The MIL illuminates and the transmission system defaults to limp-in
mode.

Monitor Conditions

When Monitored:

In any forward gear with engine speed above 1000 RPM, shortly after a shift and every minute thereafter.

Set Conditions

l Set Condition:

After a shift into a forward gear, with engine speed greater than 1000 RPM, the PCM momentarily turns
on element pressure to the clutch circuits that don't have pressure to identify the correct pressure switch
closes. If the pressure switch does not close 2 times, the DTC sets.

Possible Causes

Possible Causes
LOSS OF PRIME P0944 PRESENT
(T16) TRANSMISSION CONTROL OUTPUT CIRCUIT OPEN
(T9) OD PRESSURE SIGNAL CIRCUIT OPEN
(T9) OD PRESSURE SIGNAL CIRCUIT SHORT TO GROUND
(T9) OD PRESSURE SIGNAL CIRCUIT SHORT TO VOLTAGE
TRANSMISSION SOLENOID/PRESSURE SWITCH ASSEMBLY
INTERNAL TRANSMISSION
POWERTRAIN CONTROL MODULE

Always perform the 42RLE PRE-DIAGNOSTIC TROUBLESHOOTING PROCEDURE before


proceeding.

Diagnostic Test

1. CHECKING FOR LOSS OF PRIME DTC

With the scan tool, read DTCs.

jueves, 3 de noviembre de 2022 12:44:49 p. m. Page 2 © 2011 Mitchell Repair Information Company, LLC.
2008 Jeep Wrangler Unlimited X
2008 AUTOMATIC TRANSMISSION 42RLE - Electrical Diagnostics - Wrangler

Is the DTC P0944 present also?

Yes

Refer to appropriate Transmission ELECTRICAL DIAGNOSTICS article and perform the


appropriate symptom.

No

Go to 2.
2. CHECK FOR RELATED DTCS

With the scan tool, read DTCs.

Are any of the DTCs P0732, P0734 and/or P0846 present also?

Yes

Replace the Transmission Solenoid/Pressure Switch Assembly per the Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST.

No

Go to 3.
3. CHECK IF THE DTC IS CURRENT

With the scan tool, read DTCs.

Is the status Active or is the Starts Since Set counter 2 or less for this DTC?

Yes

Go to 4.

No

Go to 9.
4. CHECK THE PCM AND WIRING USING THE TRANSMISSION SIMULATOR

Turn the ignition off to the lock position.

Remove the Starter Solenoid Relay from the TIPM.

CAUTION: Removal of the Starter Solenoid Relay from the TIPM will prevent the
vehicle from being started in gear.

jueves, 3 de noviembre de 2022 12:44:49 p. m. Page 3 © 2011 Mitchell Repair Information Company, LLC.
2008 Jeep Wrangler Unlimited X
2008 AUTOMATIC TRANSMISSION 42RLE - Electrical Diagnostics - Wrangler

WARNING: The Starter Solenoid Relay must be removed from the TIPM. Failure
to do so can result in personal injury or death.

Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmission Adapter kit.

Ignition on, engine not running.

With the Transmission Simulator, turn the Pressure Switch selector switch to OD.

With the scan tool, monitor the UD Pressure Switch state while pressing the Pressure Switch Test button
on the Transmission Simulator.

Wiggle the wires leading to the PCM while pressing and holding the Pressure Switch Test button.

Did the OD Pressure Switch state change to closed and remain closed while wiggling the wires?

Yes

Disassemble and inspect the Valve Body per the Service Information and repair or replace as
necessary. If no problems are found in the Valve Body, replace the Transmission Solenoid/Pressure
Switch Assembly.
Perform 42RLE TRANSMISSION VERIFICATION TEST.

No

Go to 5.
5. CHECK THE (T9) OD PRESSURE SIGNAL CIRCUIT FOR AN OPEN

jueves, 3 de noviembre de 2022 12:44:49 p. m. Page 4 © 2011 Mitchell Repair Information Company, LLC.
2008 Jeep Wrangler Unlimited X
2008 AUTOMATIC TRANSMISSION 42RLE - Electrical Diagnostics - Wrangler

jueves, 3 de noviembre de 2022 12:44:49 p. m. Page 5 © 2011 Mitchell Repair Information Company, LLC.
2008 Jeep Wrangler Unlimited X
2008 AUTOMATIC TRANSMISSION 42RLE - Electrical Diagnostics - Wrangler

Fig. 65: Checking OD Pressure Switch Sense Circuit For Open


Courtesy of CHRYSLER LLC

Turn the ignition off to the lock position.

Disconnect the PCM C4 harness connector.

Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.

NOTE: Check connectors - Clean/repair as necessary.

CAUTION: Do not probe the PCM harness connectors. Probing the PCM harness
connectors will damage the PCM terminals resulting in poor terminal
to pin connection. Install Miller tool #8815 to perform diagnosis.

Measure the resistance of the (T9) OD Pressure Signal circuit between the Transmission
Solenoid/Pressure Switch Assembly harness connector and the appropriate terminal of Miller tool #8815.

Is the resistance above 5.0 ohms?

Yes

Repair the (T9) OD Pressure Signal circuit for an open.


Perform 42RLE TRANSMISSION VERIFICATION TEST.

No

Go to 6.
6. CHECK THE (T9) OD PRESSURE SIGNAL CIRCUIT FOR A SHORT TO GROUND

jueves, 3 de noviembre de 2022 12:44:49 p. m. Page 6 © 2011 Mitchell Repair Information Company, LLC.
2008 Jeep Wrangler Unlimited X
2008 AUTOMATIC TRANSMISSION 42RLE - Electrical Diagnostics - Wrangler

jueves, 3 de noviembre de 2022 12:44:49 p. m. Page 7 © 2011 Mitchell Repair Information Company, LLC.
2008 Jeep Wrangler Unlimited X
2008 AUTOMATIC TRANSMISSION 42RLE - Electrical Diagnostics - Wrangler

Fig. 66: Checking OD Pressure Switch Sense Circuit For Short To Ground
Courtesy of CHRYSLER LLC

Measure the resistance between ground and the (T9) OD Pressure Signal circuit.

Is the resistance below 5.0 ohms?

Yes

Repair the (T9) OD Pressure Signal circuit for a short to ground.


Perform 42RLE TRANSMISSION VERIFICATION TEST.

No

Go to 7.
7. CHECK THE (T9) OD PRESSURE SIGNAL CIRCUIT FOR A SHORT TO VOLTAGE

jueves, 3 de noviembre de 2022 12:44:49 p. m. Page 8 © 2011 Mitchell Repair Information Company, LLC.
2008 Jeep Wrangler Unlimited X
2008 AUTOMATIC TRANSMISSION 42RLE - Electrical Diagnostics - Wrangler

jueves, 3 de noviembre de 2022 12:44:49 p. m. Page 9 © 2011 Mitchell Repair Information Company, LLC.
2008 Jeep Wrangler Unlimited X
2008 AUTOMATIC TRANSMISSION 42RLE - Electrical Diagnostics - Wrangler

Fig. 67: Measuring Voltage Of (T9) OD Pressure Signal Circuit


Courtesy of CHRYSLER LLC

Ignition on, engine not running.

With the scan tool under TIPM, actuate the Transmission.

Measure the voltage of the (T9) OD Pressure Signal circuit.

Is the voltage above 0.5 volts?

Yes

Repair the (T9) OD Pressure Signal circuit for a short to voltage.


Perform 42RLE TRANSMISSION VERIFICATION TEST.

No

Go to 8.
8. CHECK THE (T16) TRANSMISSION CONTROL OUTPUT CIRCUIT FOR AN OPEN

jueves, 3 de noviembre de 2022 12:44:49 p. m. Page 10 © 2011 Mitchell Repair Information Company, LLC.
2008 Jeep Wrangler Unlimited X
2008 AUTOMATIC TRANSMISSION 42RLE - Electrical Diagnostics - Wrangler

Fig. 68: Checking (T16) Transmission Control Output Circuits


Courtesy of CHRYSLER LLC

With the scan tool under TIPM, actuate the Transmission.

Using a 12-volt test light connected to ground, check (T16) Transmission Control Output circuit in the
Transmission Solenoid/Pressure Switch Assembly harness connector.

NOTE: The test light must illuminate brightly. Compare the brightness to that of a
direct connection to the battery.

Does the test light illuminate brightly?

Yes

Using the schematics as a guide, check the Powertrain Control Module (PCM) terminals for
corrosion, damage, or terminal push out. Pay particular attention to all power and ground circuits. If
no problems are found, replace and program the PCM per the Service Information. With the scan
tool, perform Quick Learn.
Perform 42RLE TRANSMISSION VERIFICATION TEST.

jueves, 3 de noviembre de 2022 12:44:49 p. m. Page 11 © 2011 Mitchell Repair Information Company, LLC.
2008 Jeep Wrangler Unlimited X
2008 AUTOMATIC TRANSMISSION 42RLE - Electrical Diagnostics - Wrangler

No

Repair the (T16) Transmission Control Relay Output circuit for an open. If the fuse is open make
sure to check for a short to ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST.
9. CHECK THE WIRING AND CONNECTORS

The conditions necessary to set the DTC are not present at this time.

Using the schematics as a guide, inspect the wiring and connectors specific to this circuit.

Wiggle the wires while checking for shorted and open circuits.

With the scan tool, check the Event Data to help identify the conditions in which the DTC was set.

Were there any problems found?

Yes

Repair as necessary.
Perform 42RLE TRANSMISSION VERIFICATION TEST.

No

Test Complete.

jueves, 3 de noviembre de 2022 12:44:49 p. m. Page 12 © 2011 Mitchell Repair Information Company, LLC.

You might also like