TESNIT® BA-CF

TESNIT® BA-CF has excellent thermal and chemical resistance to strong alkaline media.
TESNIT® BA-CF is suitable for high temperature applications, petrochemicals and for the
paper and cellulose industries.

PROPERTIES APPROPRIATE INDUSTRIES & APPLICATIONS

SUPERIOR POTABLE WATER SUPPLY PETROCHEMICAL INDUSTRY
THERMAL CHEMICAL
RESISTANCE RESISTANCE
EXCELENT STEAM SUPPLY PAPER MILLS AND
MECHANICAL CELULOSE INDUSTRY
RESISTANCE
VERY GOOD GAS SUPPLY SHIPBUILDING

GOOD SEALABILITY CHEMICAL INDUSTRY HIGH TEMP. APPLICATIONS
PERFORMANCE
MODERATE

Carbon fibres, inorganic fillers, NBR binder.

Composition Optional steel wire mesh or expanded steel insert on request.

Colour Black

Approvals DIN-DVGW DIN 3535-6, DVGW VP 401, DVGW KTW, BAM (Oxygen), Germanischer Lloyd

TECHNICAL DATA Typical values for a thickness of 2 mm

Density DIN 28090-2 g/cm3 1.7
Compressibility ASTM F36J % 9
Recovery ASTM F36J % 60
Tensile strengthx ASTM F152 MPa 12
Stress resistance DIN 52913
16 h, 50 MPa, 175 °C MPa 35
16 h, 50 MPa, 300 °C MPa 30
Specific leak rate DIN 3535-6 mg/(s.m) 0.09
Thickness increase ASTM F146
Oil IRM 903, 5 h, 150 °C % 5
ASTM Fuel B, 5 h, 23 °C % 5
Compression modulus DIN 28090-2
At room temperature: εKSW % 7.3
At elevated temperature: εWSW/200 °C % 8.3
Percentage creep relaxation DIN 28090-2
At room temperature: εKRW % 3.6
At elevated temperature: εWRW/200 °C % 1.0
Max. operating conditions
Peak temperature °C/°F 400/752
Continuous temperature °C/°F 300/572
- with steam °C/°F 280/536
Pressure bar/psi 100/1450

P-T DIAGRAM
EN 1514-1, Type IBC, PN 40, DIN 28091-2 / 3.8, 2.0 mm
150 General suitability - Under common installation practices and chemical
compatibility.
100 Conditional suitability - Appropriate measures ensure maximum performance
PRESSURE [bar]

for joint design and gasket installation. Technical consultation is recommended.

Limited suitability - Technical consultation is mandatory.
50

0
-50 0 50 100 150 200 250 300 350
TEMPERATURE [˚C]
Surface finish Surface finish is 4AS. Optional graphite or PTFE finish on request.

Sheet size (mm): 1500 x 1500 | 3000 x 1500 | 4500 x 1500

Dimensions of standard sheets Thickness (mm): 0.5 | 1.0 | 1.5 | 2.0 | 3.0
Other dimensions and thicknesses are available on request.
± 5 % on length and width
Tolerances On thickness up to 1.0 mm ± 0.1 mm
On thickness above 1.0 mm ± 10 %

Acetamide + Dioxane – Oleic acid + BO DIAGRAM

Acetic acid, 10% + Diphyl (Dowtherm A) + Oleum (Sulfuric acid, fuming) – DIN 28090-1
Acetic acid, 100% (Glacial) ? Esters ? Oxalic acid ? 400.0
Acetone ? Ethane (gas) + Oxygen (gas) – 350.0
BA-CF 0.5 mm

– ? +
BA-CF 1 mm
Acetonitrile Ethers Palmitic acid BA-CF 1.5 mm
300.0 BA-CF 2 mm
Acetylene (gas) + Ethyl acetate ? Paraffin oil + 250.0
BA-CF 3 mm
Acid chlorides – Ethyl alcohol (Ethanol) + Pentane +

BO [MPa]
200.0
Acrylic acid ? Ethyl cellulose ? Perchloroethylene – 150.0
Acrylonitrile – Ethyl chloride (gas) – Petroleum (Crude oil) + 100.0
Adipic acid + Ethylene (gas) + Phenol (Carbolic acid) – 50.0
Air (gas) + Ethylene glycol + Phosphoric acid, 40% ? 0.0
Alcohols + Formaldehyde (Formalin) ? Phosphoric acid, 85% – 0 50 100 150 200 250 300
TEMPERATURE [˚C]
Aldehydes ? Formamide ? Phthalic acid +
Alum + Formic acid, 10% + Potassium acetate + σBO diagrams represents σBO values for different
Aluminium acetate + Formic acid, 85% ? Potassium bicarbonate + gasket material thicknesses. These values indicate the
Aluminium chlorate ? Formic acid, 100% – Potassium carbonate + maximum in-service compressive pressures which can
Aluminium chloride ? Freon-12 (R-12) + Potassium chloride + be applied on the compressed gasket area in-service
Aluminium sulfate ? Freon-134a (R-134a) + Potassium cyanide + without destructing damaging the gasket material.
Amines – Freon-22 (R-22) ? Potassium dichromate ?
Ammonia (gas) ? Fruit juices + Potassium hydroxide ?
Ammonium bicarbonate + Fuel oil + Potassium iodide +
Ammonium chloride + Gasoline + Potassium nitrate +
Ammonium hydroxide + Gelatin + Potassium permanganate ? P-T diagrams indicate the maximum allowed
Amyl acetate ? Glycerine (Glycerol) + Propane (gas) + combination of internal pressure and service
Anhydrides ? Glycols + Propylene (gas) + temperature which can be applied simultaneously
Aniline – Helium (gas) + Pyridine – for a given gasket depending on its material type,
Anisole ? Heptane + Salicylic acid ? thickness, size and tightness class. Given the variety
Argon (gas) + Hydraulic oil (Glycol based) + Seawater/brine + of gasket applications and service conditions, these
values should only be regarded as guidance for the
Asphalt + Hydraulic oil (Mineral type) + Silicones (oil/grease) +
proper gasket assembly. In general, thinner gaskets
Barium chloride + Hydraulic oil (Phosphate ester based) ? Soaps + exhibit better P-T properties.
Benzaldehyde – Hydrazine – Sodium aluminate +
Benzene + Hydrocarbons + Sodium bicarbonate +
Benzoic acid ? Hydrochloric acid, 10% ? Sodium bisulfite +
Bio-diesel + Hydrochloric acid, 37% – Sodium carbonate +
Bio-ethanol + Hydrofluoric acid, 10% – Sodium chloride +
Black liquor ? Hydrofluoric acid, 48% – Sodium cyanide +
Borax + Hydrogen (gas) + Sodium hydroxide ?
Boric acid + Iron sulfate + Sodium hypochlorite (Bleach) ? CHEMICAL RESISTANCE CHART
Butadiene (gas) + Isobutane (gas) + Sodium silicate (Water glass) + The recommendations made here are intended to be
Butane (gas) + Isooctane + Sodium sulfate + a guideline for the selection of the suitable gasket
Butyl alcohol (Butanol) + Isoprene + Sodium sulfide + quality. Because the function and durability of the
products depend upon a number of factors, the data
Butyric acid + Isopropyl alcohol (Isopropanol) + Starch +
may not be used to support any warranty claims.
Calcium chloride + Kerosene + Steam +
Calcium hydroxide + Ketones ? Stearic acid +
Carbon dioxide (gas) + Lactic acid ? Styrene ? + Recommended
Carbon monoxide (gas) + Lead acetate + Sugars + ? Recommendation depends on operating conditions
Cellosolve ? Lead arsenate + Sulfur ? - Not recommended
Chlorine (gas) – Magnesium sulfate + Sulfur dioxide (gas) ?
Chlorine (in water) – Maleic acid ? Sulfuric acid, 20% –
Chlorobenzene ? Malic acid ? Sulfuric acid, 98% –
Chloroform – Methane (gas) + Sulfuryl chloride –
Chloroprene ? Methyl alcohol (Methanol) + Tar +
Chlorosilanes – Methyl chloride (gas) ? Tartaric acid ?
Chromic acid – Methylene dichloride ? Tetrahydrofuran (THF) –
Citric acid ? Methyl ethyl ketone (MEK) ? Titanium tetrachloride – DONIT TESNIT®, d.o.o.
Copper acetate + N-Methyl-pyrrolidone (NMP) ? Toluene +
Copper sulfate + Milk + 2,4-Toluenediisocyanate ? Cesta komandanta Staneta 38
1215 Medvode, Slovenia
Creosote ? Mineral oil (ASTM no.1) + Transformer oil (Mineral type) +
Cresols (Cresylic acid) – Motor oil + Trichloroethylene – Phone: +386 (0)1 582 33 00
Cyclohexane + Naphtha + Vinegar + Fax: +386 (0)1 582 32 06
Cyclohexanol + Nitric acid, 10% – Vinyl chloride (gas) – +386 (0)1 582 32 08
Cyclohexanone ? Nitric acid, 65% – Vinylidene chloride – Web: www.donit.eu
Decalin + Nitrobenzene – Water +
E-mail: info@donit.eu
Dextrin + Nitrogen (gas) + White spirits +
Dibenzyl ether ? Nitrous gases (NOx) ? Xylenes +
Dibutyl phthalate ? Octane + Xylenol –
Dimethylacetamide (DMA) ? Oils (Essential) + Zinc sulfate +
Copyright © 2015 DONIT TESNIT, d.o.o.
Dimethylformamide (DMF) ? Oils (Vegetable) +
All rights reserved
All information and data quoted are based upon years of experience in the production and operation of sealing elements. This data may not be used
to support any warranty claims. With its publication this latest edition supersedes all previous issues and is subject to change without further notice. Date of issue: 01.06.2015 / TDS-BACF-05-2015