Ax2500 en

Digital Servo Amplifier
AX2500
Assembly, Installation, Setup

Keep all product manuals as a product component
during the life span of the servo amplifier.
Pass all product manuals to future
users / owners of the servo amplifier.
Edition 06/2007
Previous editions
Edition Comments
07/03 First edition
SSI emulation updated (Multiturn), UL/cUL information updated,
07/05
typographical changes, chapter 1 new sorted, several corrections
02/06 Chapter feedback updated, label updated, several small corrections
PROFIBUS Topologie, part number scheme, trouble-shooting reduced, "Components of a servo
system" extended and moved, disposal acc. to WEEE-2002/96/EG, new document structure,
06/07 Quickstart integrated, EtherCat type new, 24V supply voltage hints, feedback expanded,
BISS-Interface, Stop/Emergency-Stop expanded, shock-hazard protection new, DC-Bus link ex-
panded, accessories removed, timing diagramm motor brake
WINDOWS is a registered trademark of Microsoft Corp.

HIPERFACE is a registered trademark of Max Stegmann GmbH
EnDat is a registered trademark of Dr.Johannes Heidenhain GmbH
Technical changes to improve the performance of the equipment may be made without notice !
Printed in the Federal Republic of Germany
All rights reserved. No part of this work may be reproduced in any form (by printing, photocopying, microfilm
or any other method) or processed, copied or distributed by electronic means without the written permission
of BECKHOFF.
BECKHOFF 06/2007 Contents
page
1 General
1.1 About this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
1.2 Hints for the online edition (PDF format) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
1.3 Symbols used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
1.4 Abbreviations used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2 Safety
2.1 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
2.2 Use as directed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
3 Standards
3.1 European Directives and Standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
3.2 American Directives and Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
3.3 Asian Directives and Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
3.4 Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
3.4.1 CE conformance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
3.4.2 UL and cUL- Conformance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
4 Handling
4.1 Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
4.2 Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
4.3 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
4.4 Maintenance / Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
4.5 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
5 Package
5.1 Package supplied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
5.2 Nameplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
5.3 Part number scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
6 Technical description
6.1 Digital servo amplifiers in the series AX2500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
6.2 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
6.2.1 Rated data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
6.2.2 Inputs / Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
6.2.3 Recommended tightening torques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
6.2.4 Fusing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
6.2.5 Ambient conditions, ventilation, mounting position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.2.6 Conductor cross-sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
6.3 LED display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
6.4 Control for motor holding brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
6.5 Grounding system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
6.6 Regen circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
6.7 Switch-on/-off behavior. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
6.7.1 Behavior in standard operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
6.7.2 Behavior in the event of an error (with standard setting) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6.8 Stop / Emergency Stop Function to EN 60204. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
6.8.1 Stop: Standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
6.8.2 Emergency Stop: Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
6.8.3 Implementation of the Stop Category 0. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
6.9 Shock-hazard protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
6.9.1 Leakage current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
6.9.2 Residual-current circuit breakers (FI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
6.9.3 Isolating transformers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
AX2500 Product Manual 3

Contents 06/2007 BECKHOFF
page
7 Mechanical Installation
7.1 Important notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
7.2 Guide to mechanical installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
7.3 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
7.4 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
7.5 Add-on fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
8 Electrical Installation
8.1 Important notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
8.2 Guide to electrical installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
8.3 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
8.3.1 Important notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
8.3.2 Shield connection on the front panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
8.3.3 Requirements to cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
8.4 Components of a servo system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
8.5 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
8.6 Connector assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
8.7 Connection diagram AX250x and AX251x (overview) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
8.8 Connection diagram AX252x (overview) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
8.9 Power supply, master only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
8.9.1 Mains supply connection (X0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
8.9.2 24V auxiliary voltage (X0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
8.10 DC Bus link (X0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
8.11 Motor connection with brake (X6). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
8.12 External regen resistor (X0), master only. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
8.13 Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
8.13.1 Resolver (X5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
8.13.2 Sine encoder 5V with BISS (X2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
8.13.3 Sine Encoder with EnDat 2.1 or HIPERFACE (X2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
8.13.4 Sine Encoder without data channel (X2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
8.13.5 Incremental or sine encoder with hall sensors (X2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
8.13.6 Incremental Encoder (X4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
8.14 Electronic Gearing, Master-slave operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
8.14.1 Connection to a AX2500 master, 5 V signal level (X4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
8.14.2 Connection to incremental encoder master with 24 V signal level (X3) . . . . . . . . . . . . . . . . 57
8.14.3 Connection to a sine-cosine encoder master (X2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
8.14.4 Connection to a SSI encoder (X4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
8.14.5 Connection to stepper motor controllers (pulse and direction) . . . . . . . . . . . . . . . . . . . . . . . . 59
8.14.5.1 Step/Direction with 5 V signal level (X4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
8.14.5.2 Step/Direction with 24 V signal level (X3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
8.15 Encoder emulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
8.15.1 Incremental encoder output - A quad B (X4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
8.15.2 SSI output (X4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
8.16 Digital and analog inputs and outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
8.16.1 Analog input (X3). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
8.16.2 Digital inputs (X3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
8.16.3 Digital outputs (X3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
8.16.4 Digital I/O on the Master (X1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
8.17 RS232 interface, PC connection (X8), master only. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
8.18 Fieldbus connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
8.18.1 CANopen interface (X7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
8.18.2 PROFIBUS interface (X7), option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
8.18.3 SERCOS interface (X7), option. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
8.18.3.1 Light emitting diodes (LEDs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
8.18.3.2 Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
8.18.4 EtherCat interface (X7), option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
8.18.4.1 EtherCat connection, connector X7A/B (RJ-45) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
8.18.4.2 Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
4 AX2500Product Manual
BECKHOFF 06/2007 Contents
page
9 Setup
9.1 Important notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
9.2 Setup software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
9.2.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
9.2.1.1 Use as directed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
9.2.1.2 Software description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
9.2.1.3 Hardware requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
9.2.1.4 Operating systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
9.2.2 Installation under WINDOWS 98 / 2000 / ME / NT / XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
9.3 Quickstart, drive test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
9.3.1 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
9.3.1.1 Unpacking, Mounting and Wiring the Servo Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
9.3.1.2 Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
9.3.1.3 Minimum Wiring for Drive Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
9.3.2 Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
9.3.3 Important Screen Elements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
9.3.4 Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
9.3.5 Motor (synchronous) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
9.3.6 Feedback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
9.3.7 Save Parameters and Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
9.3.8 Jogging the Motor (Speed Control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
9.3.9 Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
9.3.10 Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
9.3.11 Additional Setup Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
9.4 Multi-axis systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
9.4.1 Station Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
9.4.2 Example of connections for multi-axis system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
9.5 Key pad controls and status displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
9.5.1 Operating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
9.5.2 Status display on the axis module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
9.5.3 Status display on the master . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
9.6 Error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
9.7 Warning messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
9.8 Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
10 Appendix
10.1 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
10.2 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95

06/2007 BECKHOFF
This page has been deliberately left blank.
6 AX2500 Product Manual

BECKHOFF 06/2007 General
1 General
1.1 About this manual
This manual describes the digital servo amplifiers of the AX2500 series.
A more detailed description of the field bus interfaces and the digital connection to auto-
mation systems can be found on the accompanying CD-ROM in PDF format (system
requirements: WINDOWS, Internet browser, Acrobat Reader) in several language ver-
sions.
You can print out this documentation on any standard printer. A printed copy of the docu-
mentation is available from us at extra cost.
This manual makes the following demands on qualified personnel :

Transport: only by personnel with knowledge of handling
electrostatically sensitive components.
Unpacking: only by electrically qualified personnel.
Installation: only by electrically qualified personnel.
Setup: only by qualified personnel with extensive knowledge of
electrical engineering / drive technology.
1.2 Hints for the online edition (PDF format)

Bookmark:
Table of contents and index are active bookmarks.
Table of contents and index in the text:
The lines are active cross references. Click on the desired line and the appropriate page
is indicated.
Page/chapter numbers in the text:
Page/chapter numbers with cross references are active. Click at the page/chapter num-
ber to reach the indicated target.
1.3 Symbols used
Danger to personnel
Danger to maschinery, Important
from electricity and its
general warning notes
effects effects
ð p. see page l special emphasis

General 06/2007 BECKHOFF
1.4 Abbreviations used

The abbreviations used in this manual are explained in the table below.
Abbrev. Meaning
AGND Analog ground
BTB/RTO Ready to operate
CAN Fieldbus (CANopen)
CE Communité Europeenne (=EC)
CLK Clock signal
COM Serial interface for a PC-AT
DGND Digital ground
DIN Deutsches Institut für Normung
Disk Magnetic storage (diskette, hard disk)
EEPROM Electrically erasable memory
EMC Electromagnetic compatibility
EMI Elektromagnetic interference
EN European standard
ESD Electrostatic discharge
F-SMA Fiber Optic Cable connector according to IEC 60874-2
IEC International Electrotechnical Commission
IGBT Insulated gate bipolar transistor
ISO International Standardization Organization
LED Light-emitting diode
MB Megabyte
NI Zero pulse
NSTOP Limit-switch input, rot. dir. CCW (left)
PC Personal Computer
PELV Protected low voltage
PLC Programmable logic controller
PSTOP Limit-switch input, rot. dir. CW (right)
PSU Power supply unit
PWM Pulse-width modulation
RAM Volatile memory
RBext External regen resistor
RBint Internal regen resistor
RES Resolver
ROD 426 A quad B Encoder
SRAM Static RAM
SSI Synchronous serial interface
UL Underwriter Laboratory
V AC AC voltage
V DC DC voltage
VDE Verein deutscher Elektrotechniker

BECKHOFF 06/2007 Safety
2 Safety
2.1 Safety Instructions
l Only properly qualified personnel are permitted to carry out activities such as
transport, installation, commissioning and maintenance. Properly qualified per-
sons are those who are familiar with the transport, assembly, installation, com-
missioning and operation of the product, and who have the appropriate qualifi-
cations for their job. The qualified personnel must know and observe the
following standards and regulations:
— IEC 60364 or DIN VDE 0100
— IEC 60664 or DIN VDE 0110
— national accident prevention regulations or BGV A3
l Read this documentation before carrying out the installation and commissio-
ning. Incorrect handling of the servo amplifier can lead to personal injury or
material damage. It is vital that you keep to the technical data and information
on connection requirements (nameplate and documentation).
l Discharge your body before touching the servo amplifier. The servo amplifiers
contain electrostatically sensitive components which may be damaged by in-
correct handling. Avoid contact with highly insulating materials (artificial fab-
rics, plastic film etc.). Place the servo amplifier on a conductive surface.
l The manufacturer of the machine must produce a hazard analysis for the ma-
chine and take appropriate measures to ensure that unforeseen movements do
not result in personal injury or material damage.
l Do not open or touch the equipment during operation. Keep all covers and ca-
binet doors closed during operation. Touching the equipment is allowed du-
ring installation and commissioning for properly qualified persons only. Other-
wise, there are deadly hazards, with the possibility of death, severe injury or
material damage.
— During operation, servo amplifiers may have uncovered live
components, depending on their level of enclosure protection.
— Control and power connections may be live, even though the
motor is not rotating.
— Servo amplifiers may have hot surfaces during operation.
Surface can reach temperatures above 80°C.
l Never undo any electrical connections to the servo amplifier while it is live.
There is a danger of electrical arcing with damage to contacts and personal in-
jury.
Wait at least five minutes after disconnecting the servo amplifier from the main
supply power before touching potentially live sections of the equipment (e.g.
contacts) or undoing any connections. Capacitors can still have dangerous
voltages present up to five minutes after switching off the supply power. To be
sure, measure the voltage in the DC Bus link and wait until it has fallen below
40V.

Safety 06/2007 BECKHOFF
2.2 Use as directed

l The servo amplifiers are components which are built into electrical equipment or ma-
chines, and can only be commissioned as integral components of such equipment.
l The manufacturer of the machine must produce a hazard analysis for the ma-
chine and take appropriate measures to ensure that unforeseen movements do
not result in personal injury or material damage.
l The servo amplifier should only be used with power supplies with a maximum
symmetrical rated current of 5000A and a voltage of 115/230V AC (AX250x) or
400V AC (AX251x).
Mains voltage Servo amplifier

1 x 115V AC only AX250x, unearthed operation is permissible
3 x 230V AC all types, unearthed operation is permissible
3 x 400V AC only AX251x, TN-system or TT-system with earthed neutral point
l If the servo amplifiers are used in residential areas, or in business or commercial

premises, then additional filter measures must be implemented by the user.
l The AX2500 family of servo amplifiers is only intended to drive specific brushless
synchronous servomotors with closed-loop control of torque, speed and/or position.
The rated voltage of the motors must be at least as high as the DC Bus link voltage
of the servo amplifier.
l The servo amplifiers may only be operated in a closed control cabinet, taking into
account the ambient conditions defined on page 20. Ventilation or cooling measures
may be required to keep the temperature below 45°C.
l Use only copper-cored cables for wiring. The conductor cross-sections can be taken
from the European standard EN 60204 (or Table 310-16 of NEC for 60°C or 75°C in
the column for AWG cross-sections).
l We can only guarantee that the system will conform to the standards cited on page
11 if the components used are exclusively those supplied by us (servo amplifier, mo-
tor, cables etc.).
l Not more than 7 axis modules can be connected to a master module.

BECKHOFF 06/2007 Standards
3 Standards
3.1 European Directives and Standards
Servo amplifiers are components that are intended to be incorporated into electrical plant
and machines for industrial use. When the servoamplifiers are built into machines or
plant, the intended operation of the amplifier is forbidden until it has been established that
the machine or plant fulfills the requirements of the EC Machinery Directive 98/37/EG and
the EC Directive on EMC (89/336/EEC) and the Low Voltage Directive 73/23/EEC.
To fulfill the EC Machinery directive 98/37/EG, the following standards have to be applied:
EN 60204-1 (Safety and electrical equipment of machines)
EN 12100 (Safety of machines)
The manufacturer of the machine must produce a hazard analysis for the machine
and take appropriate measures to ensure that unforeseen movements do not result
in personal injury or material damage.
To fulfill the Low Voltage Directive 73/23/EEC, the following standards have to be applied:
EN 60204-1 (Safety and electrical equipment of machines)
EN 50178 (Equipment of high voltage plant with electronic devices)
EN 60439-1 (Low-voltage switchgear and controlgear assemblies)
To fulfill the EC EMC regulations 89/336/EEC, the following standards have to be applied:
EN 61000-6-1 or EN 61000-6-2 (noise immunity in the domestic range/industrial range)
EN 61000-6-3 or EN 61000-6-4 (noise emission in the domestic range/industrial range)
The manufacturer of the machine or plant is responsible for ensuring that they meet the
limits required by the EMC regulations. Advice on the correct installation for EMC – such
as shielding, grounding, arrangement of connectors and cable routing – can be found in
this documentation.
The machine / plant manufacturer must examine whether with its machine / plant
still further or other standards or EEC guidelines are to be used.
3.2 American Directives and Standards

Chapter in process
3.3 Asian Directives and Standards

Chapter in process

Standards 06/2007 BECKHOFF
3.4 Approvals
3.4.1 CE conformance
Conformity with the EC Directive on EMC 89/336/EEC and the Low Voltage Directive
73/23/EEC is mandatory for servoamplifiers supplied within the European Union.
To fulfill the EMC directive, the standard EN 61800-3 is applied. The Declaration of Con-
formity form can be found on our website (download area).
In the reference to noise immunity the servoamplifier fulfills the requirement to the cate-
gory second environment (industrial environment). For noise emission the amplifier meets
the requirement to a product of the category C2 (motor cable £ 25m).
Warning!
This product can cause high-frequency interferences in non industrial
environments which can require measures for interference suppression.
The servo amplifiers have been tested by an authorized testing laboratory in a defined
configuration with the system components which are described in this documentation.
Any divergence from the configuration and installation described in this documentation
means that you will be responsible for carrying out new measurements to ensure that the
regulatory requirements are fulfilled.
To fulfill the Low Voltage Directive, the standard EN 50178 has to be applied.
3.4.2 UL and cUL- Conformance
This servo amplifier is listed under UL file number E217428.

UL (cUL)-certified servo amplifiers (Underwriters Laboratories Inc.) fulfil the relevant U.S.
and Canadian standard (in this case UL 840 and UL 508C).
This standard describes the fulfilment by design of minimum requirements for electrically
operated power conversion equipment, such as frequency converters and servo amplifi-
ers, which is intended to eliminate the risk of fire, electric shock, or injury to persons,
being caused by such equipment.
UL(cUL) regulations also specify the minimum technical requirements of electrical
devices, in order to take the necessary measures against the risk of fire, which can be
triggered by electrically operated devices. The technical conformance with the U.S. and
Canadian standard is determined by an independent UL (cUL) inspector through the type
testing and regular checkups.
Apart from the notes on installation and safety in the documentation, the customer does
not have to observe any other points in direct connection with the UL (cUL)-certification of
the equipment.
UL 508C
UL 508C describes the fulfilment by design of minimum requirements for electrically oper-
ated power conversion equipment, such as frequency converters and servo amplifiers,
which is intended to eliminate the risk of fire being caused by such equipment.
UL 840
UL 840 describes the fulfilment by design of air and insulation creepage spacings for
electrical equipment and printed circuit boards.

BECKHOFF 06/2007 Handling
4 Handling
4.1 Transport
l Transport only by qualified personnel in the manufacturer’s original packaging
l Avoid shocks
l Transport temperature -25 to +70°C, max. rate of change 20°C/hour
l Transport humidity max. 95% relative humidity, no condensation
l The servo amplifiers contain electrostatically sensitive components which can
be damaged by incorrect handling. Discharge yourself before touching the ser-
vo amplifier. Avoid contact with highly insulating materials (artificial fabrics,
plastic films etc.). Place the servo amplifier on a conductive surface.
l If the packaging is damaged, check the unit for visible damage. In such a case, in-
form the shipper and the manufacturer.
4.2 Packaging
l Recyclable cardboard with inserts
l Dimensions AX252x (HxWxD) 100x300x270 mm
AX250x/AX251x (HxWxD) 150x300x270 mm
l Labelling instrument label on outside of box
4.3 Storage
l Storage only in the manufacturer’s original recyclable packaging
l Max. stacking height: 8 cartons
l Storage temp. –25 to +55°C, max. rate of change 20°C/hr
l Humidity relative humidity max. 5...95%, no condensation
l Storage duration
< 1 year without restriction
> 1 year: capacitors must be re-formed before the servo amplifier is commissioned.
To do this, remove all electrical connections and supply the servo amplifier for about
30 min. from 230V AC, single-phase, on terminals L2 / L3.
4.4 Maintenance / Cleaning

The devices do not require any maintenance, opening the devices invalidates warranty.
Cleaning : — if the casing is dirty, clean with Isopropanol or similar
do not immerse or spray
— if there is dirt inside the unit it must be cleaned by the manufacturer
— dirty protective grill on fan must be cleaned with a dry brush
4.5 Disposal
In accordance to the WEEE-2002/96/EG-Guidelines we take old devices and accessories
back for professional disposal, if the transport costs are taken over by the sender.
Send the devices to:
Beckhoff Automation GmbH
Eiserstr. 5
D-33415 Verl

Package 06/2007 BECKHOFF
5 Package
5.1 Package supplied
If you order a AX2500 series amplifier from us, you will receive:
— AX250x or AX251x (master)
— Mating connectors for X0, X1, X3, X6
— Protective cover for the axis-side (required only once per system)
— Assembly and Installation Instructions
— Setup software DRIVE.EXE and online documentation on CD-ROM
or
— AX252x (axis module)
— Mating connector for X3, X6
— Short-form instructions
The mating SubD connectors are not part of the package supplied!
Accessories: (must be ordered separately if required)

— Electrical add-on fan (for max. 2 axes, required for AX25x6)
— Synchronous servomotor (linear or rotary)
— Motor lead (pre-assembled), or motor cable as cut-off length + loose connectors
(motor- and amplifier-side)
— Feedback cable (pre-assembled) or both feedback connectors, loose with
feedback cable as cut-off length
— External regen resistor BAR(U)
— Communication cable to PC (ð p.67) for parameterizing the master and any
attached axis modules
— Power cable, control cables, fieldbus cables (as lengths)
5.2 Nameplate
The nameplate depicted below is attached to the side of the servo amplifier.
Servo amplifier type Serial number Comments Enclosure Rating
Eiserstr. 5 Tel.: +49-(0)5246/963-0 C UL

® US
D-33415 Verl Fax: +49-(0)5246/963-149 E217428 LISTED
IND. CONT. EQ.
1VD4
Typenbezeichnung Model Number Ser. Nr Ser. No. Bemerkung Comment
Spannungsversorgung Power Supply Nennstrom Nom. Current Schutzart Encl.Rating
Umgebungstemp.
Ambient temp.
008102106842 5.76
max. ambient Electrical supply Output current

temperature Installed load in S1 operation

BECKHOFF 06/2007 Package
5.3 Part number scheme
S406A0-NA
Family Expansions
S4 AX2500 NA no expansion
PB PROFIBUS
Current rating SE SERCOS
03 3A rms EC ETHERCAT
06 6A rms
Voltage rating Function

A 230...400V A Axis module
6 115...230V M Master module
B no power supply
Comparison (without expansion) device name -> UL part number
Device Name UL Part Number

AX2503 S4036M-NA
AX2506 S4066M-NA
AX2513 S403AM-NA
AX2516 S406AM-NA
AX2523 S403BA-NA
AX2526 S406BA-NA

Technical description 06/2007 BECKHOFF
6 Technical description
6.1 Digital servo amplifiers in the series AX2500
Minimum complexity
l up to 8 axes in a single system
l only one power supply feed and one auxiliary voltage supply per system
l shield connection directly on the servo amplifier
l all axes in a system can be parameterized through a single interface
l strongly reduced wiring expenditure by modular structure
l simple mechanical structure on DIN rails
Standard version
l 2 supply voltage versions: AX250x up to 3x230VAC and
AX251x up to 3x400VAC
l one size for the master and axis modules each, see page 35
l analog input
l fieldbus interface is integrated (standard: CANopen)
l RS232 is integrated
l pulse-direction interface is integrated
Supply power
l directly off electrical supply input (master only, B6 rectifier bridge,
integral power input filter and inrush circuit):
1 x 115V AC (AX250x only, unearthed operation is permitted)
3 x 115V AC (AX250x only, unearthed operation is permitted)
1 x 230V AC (AX250x only, unearthed operation is permissible)
3 x 230V AC (all types, unearthed operation is permissible)
3 x 400V AC (AX251x only, TN-system or TT-system with
earthed neutral point)
l fusing (e.g. fusible cutout) provided by the user
l integrated interference suppression filter for the supply input (for category 2)
l integrated interference suppression filter for the 24V auxiliary supply (for category 2)
l all shielding connections directly on the amplifier
l output stage IGBT module with isolated current measurement
Clock frequency can be switched from 8 to 16 kHz with
ASCII command (with power reduction, please contact
our customer support)
l regen circuit internal regen resistor as standard,
external regen resistor if required
l DC Bus link voltage 160...320V DC for AX250x
320...560V DC for AX251x
160...560V DC for AX252x

BECKHOFF 06/2007 Technical description
Integrated safety
l safe electrical separation to EN 50178 between the power input / motor connections
and the signal electronics, provided by appropriate creepage distances and complete
electrical isolation
l Soft-start, overvoltage detection, short-circuit protection, phase-failure monitoring
l temperature monitoring of servo amplifier and motor (when using our motors with our
pre-assembled cables)
Auxiliary voltage 24V DC

l electrically isolated via an external 24V DC PSU, e.g. with isolating transformer
Operation and parameter setting

l with the comfortable setup software, via the serial interface of a PC to a single con-
nection for all axes in a system
l station address setting through two keys and a 3-digit LED status display on the
master
l fully programmable via RS232 interface
Completely digital control

l digital current controller (space vector pulse-width modulation, 62.5 µs)
l freely programmable digital speed controller (62.5 µs or 250 µs)
l integral position controller, with adaptation possibilities for every application (250 µs)
l integrated pulse direction interface, for connection of a servomotor to a
stepper-motor control
l evaluation of the resolver signals or sine/cosine signals from a high-resolution
encoder
l encoder emulation (incremental ROD 426-compatible or SSI)
Comfort functions
l 4 programmable digital inputs
(two are normally defined as limit-switch inputs)
l 2 programmable digital outputs
l freely programmable combinations of all digital signals
Options
l PROFIBUS DP interface instead of CANopen, see page 69
l SERCOS interface instead of CANopen, see page 70
l EtherCat interface instead of CANopen, see page 71

6.2 Technical data

6.2.1 Rated data
max. 230VAC max. 400VAC

Master Master Axis module
AX250 AX251 AX252
Rated data DIM 3 6 3 6 3 6
1 x 115V-10% 3 x 230V-10%
Rated supply voltage V~ to to —
3 x 230V+10% 3 x 400V+10%
Max. installed load for S1 operation
kVA 7 12 —
(in a multi-axis system)
Rated DC Bus link voltage V= 160 - 320 320 - 560 160 - 560
Rated output current
Arms 3 6* 3 6* 3 6*
(rms value, ± 3%, @ 8kHz)
Peak output current
Arms 9 12* 9 12* 9 12*
(max. ca. 5s, ± 3%, @ 8kHz)
8 (can be switched to 16, with power re-
Clock frequency of output stage kHz duction, please contact our customer sup-
port)
Overvoltage switch-off threshold V 450 750 —
maximum load inductance mH 75 40 75 40 75 40
minimum load inductance mH 12 7.5 12 7.5 12 7.5
Form factor of the output current
(rated conditions and min. load — 1.01
inductance)
Bandwidth of subordinate current
kHz > 1.2
controller
Residual voltage drop at rated
V <5
current
Quiescent dissipation, output stage
W 12 15 12 15 12 15
disabled
Dissipation at rated current
W 35 60 35 60 30 40
(without regen dissipation)
Mechanical
Weight kg 3 1.7
Height, without connectors mm 230 267* 230 267* 230 267*
Width mm 100 50
Depth, without connectors mm 240
* with add-on ventilation, see page 36

6.2.2 Inputs / Outputs
Analog input, 14-bit resolution V ±10

common-mode voltage max. V ±10
Digital control inputs V low 0...7V, high 12...36V, 7mA
Digital control outputs, open emitter V max. 30V, 10mA
V DC max. 30, AC max 42
BTB/RTO output, relay contacts
mA 500
Auxiliary supply, electrically isolated, V 20 - 30
without holding brake, without fan A n * 0.5
Auxiliary supply, electrically isolated, V 24 (-0% +15%)
with holding brake or fan
A n * 2,5
(check voltage drop !)
Min./max. output current for holding brake A 0.15 / 1.5
Connections
Control signals — Combicon spring terminal
Power supply — Power Combicon
Motor — Combicon
Resolver input — SubD 9pol. (socket)
Incremental encoder input — SubD 15pol. (socket)
PC interface — SubD 9pol. (plug)
Encoder emulation, ROD/SSI — SubD 9pol. (plug)
n= number of axes
6.2.3 Recommended tightening torques
Connector Tightening torque

X1, X3, X6 0.3 Nm
X0 1.3 Nm
Earthing bolts 3.5 Nm
lower mounting bolt 3.5 Nm
6.2.4 Fusing
Internal fusing
Function
Auxiliary supply 24V 20 AM
Regen resistor electronical
External fusing
Function Fusible cutouts or similar
AC supply FN1/2/3 16 A slow
24V supply FH1/2 20 A slow
Regen resistor FB1/2 6 A slow

6.2.5 Ambient conditions, ventilation, mounting position
Storage, transport ð p.13

Supply voltage tolerances
main power
AX250x min 1x115V-10% AC / max 1x230V+10%, 50/60 Hz
min 3x115V-10% AC / max 3x230V+10%, 50/60 Hz
AX251x min 3x230V-10% AC / max 3x400V+10%, 50/60 Hz
auxiliary supply
w/o brake and w/o fan 20 VDC ... 30 VDC
with brake or with fan 24 VDC (-0% +15%), check voltage drop
0...+45oC at rated conditions
Ambient temperature in operation
+45...+55°C with power derating 2.5% / K
Humidity in operation rel. humidity 85%, no condensation
up to 1000m amsl without restrictions
Site altitude
1000...2500m amsl with derating 1.5% / 100m
Pollution level Pollution level 2 as per EN 60204 / EN 50178
Vibrations Class 3111 according to IEC 721-3-3
Noise emission max. 45 dB(A)
Enclosure protection IP 20
Mounting position normally vertical ð p.34
AX25x3: free convection
Ventilation
AX25x6: add-on fan (ð p.36)
Make sure that there is adequate forced ventilation in the closed control cabinet.
6.2.6 Conductor cross-sections
Technical requirements to cables ð p.41.

Following EN 60204-1, we recommend :
AC connection 1.5 mm², depending on the system fusing

Motor cables, max. 25m 1 mm², shielded, capacitance <150pF/m
Resolver, motor thermostat, 4x2x0.25 mm², twisted pairs, shielded,
max.100m capacitance <120pF/m
Encoder, motor thermostat, 7x2x0.25 mm², twisted pairs, shielded,
max. 50m capacitance <120pF/m
Analog signals 0.25 mm² , twisted pairs, shielded
Control signals, BTB, DGND 0.5 mm²
Holding brake (motor) 0.75 mm², shielded, check voltage drop
max. 2.5 mm²
+24 V / XGND
Check voltage drop and total current!
To reach the max. permitted cable length, observe cable requirements ð p. 41.
6.3 LED display

A 3-digit LED display indicates the amplifier status after switching on the 24V supply
(ð p.89).

6.4 Control for motor holding brake

A motor holding brake (24V, max.1.5 A) can be controlled directly by the servo amplifier.
Check voltage drop, measure the voltage at brake input and check brake function
(brake and no brake).
This function does not ensure personnel safety!
The brake function must be enabled through the BRAKE parameter (on the screen page
for Motor): the setting is WITH.
In the diagram below you can see the timing and functional relationships between the
ENABLE signal, speed setpoint, speed and braking force.
During the internal enable delay time of 100 ms (DECDIS) the speed setpoint of the servo
amplifier is internally driven down a 10 ms ramp to 0. The brake output is switched on
when a speed of 5 rpm is reached, at the latest after 5s (EMRGTO).
The rise (fbrH) and fall (fbrL) times of the holding brakes that are built into the motors vary
for the different types of motor (see motor manual). A description of the interface can be
found on page 48.
Personnel-safe operation of the holding brake requires an additional “make” contact in
the brake circuit and a spark suppressor device (e.g. a varistor) in the recommended
brake circuit:
AX2500

6.5 Grounding system

AGND – ground reference for analog signals, internal analog ground
DGND – ground reference for digital signals and auxiliary supply voltage,
optically isolated
PGND — ground reference for position output
The electrical isolation is indicated in the block diagram (ð p.43).
6.6 Regen circuit

During braking with the aid of the motor, energy is fed back to the servo amplifier. This
energy is converted into heat in the regen resistor. The regen resistor is switched in and
out by the regen circuit. The switching thresholds for the regen circuit are adjusted to suit
the supply voltage with the aid of the setup software.
Our customer support can help you with the calculation of the regen power which is
required. A description of the interface can be found on page 48 .
Internal regen resistor 33 W

External regen resistor 33 W
Functional description
The regen circuit starts to respond when the DC Bus link voltage reaches the set value.
If the energy which is fed back from the motor, as an average over time or as a peak
value, is higher than the preset regen power, then the servo amplifier will output the sta-
tus regen power exceeded and the circuit will be switched off.
At the next internal check of the DC Bus link voltage (after a few milliseconds) an
overvoltage will be detected and the servo amplifier will be switched off, with the error
message overvoltage (ð p.90).
The BTB/RTO contact (terminals X1/1,2) will be opened simultaneously (ð p.66).
Technical data
Supply voltage Rated data DIM Value

Upper switch-on threshold for regen circuit V 400
Switch-off threshold for regen circuit V 380
Continuous int. power in regen circuit (RBint) W 55
3 x 230 V Continuous ext. power in circuit (RBext) max. kW 0,4
Pulse power, internal (RBint max. 1s) kW 4.8
Pulse power, external (RBext max. 1s) kW 4.8
External regen resistor W 33
Upper switch-on threshold for regen circuit V 720
Switch-off threshold for regen circuit V 680
Continuous int. power in regen circuit (RBint) W 80
3 x 400 V Continuous ext. power in circuit (RBext) max. kW 0,6
Pulse power, internal (RBint max. 1s) kW 16
Pulse power, external (RBext max. 1s) kW 16
External regen resistor W 33

6.7 Switch-on/-off behavior

This chapter describes the switch-on and switch-off behavior of the AX25 and the steps
required to achieve operational stopping or emergency stop behavior that complies with
standards.
The servo amplifier’s 24 V supply must remain constant. The ASCII commands
ACTFAULT (error response) and STOPMODE (ENABLE signal response) dictate
how the drive will behave.
Behavior (see also ASCII reference in the online help of

STOPMODE ACTFAULT
the setup software)
0 (default) 0 Motor coasts to a standstill in an uncontrolled manner
1 1 (default) Motor is braked in a controlled manner
Behavior during a power failure

The servo amplifiers use an integrated circuit to detect if one or more input phases
(power supply feed) fail. The behavior of the servo amplifier is set using the setup soft-
ware: Under “Response to Loss of Input Phase” (PMODE) on the Basic Setup screen,
select:
l Warning if the higher-level control system is to bring the drive to a standstill: War-
ning n05 is output if an input phase is missing, and the motor current is limited to 4 A.
The servo amplifier is not disabled. The higher-level control system can now selecti-
vely end the current cycle or start bringing the drive to a standstill. Therefore, the er-
ror message “MAINS BTB, F16" is output on a digital output of the servo amplifier
and evaluated by the control system, for instance.
l Error message if the servo amplifier is to bring the drive to a standstill: Error messa-
ge F19 is output if an input phase is missing. The servo amplifier is disabled and the
BTB contact opens. Where the factory setting is unchanged (ACTFAULT=1), the mo-
tor is braked using the set “EMERGENCY STOP RAMP”.
Behavior when undervoltage threshold is reached

If the undervoltage threshold is undershot in the DC bus link (the threshold value
depends on the type of servo amplifier), the error message “UNDERVOLTAGE, F05" is
displayed. The drive response depends on the ACTFAULT/STOPMODE setting.
Behavior with enabled “holding brake” function
Servo amplifiers with an enabled holding brake function have a special procedure for
switching off the output stage ( ð p. 21). Removing the ENABLE signal triggers electrical
braking.
As with all electronic circuits, the general rule applies that there is a possibility of the inter-
nal “holding brake” module failing. Bringing a motor to a standstill using a holding brake in
a way that is personnel safe also requires an electromechanical “make” contact for the
holding equipment and a suppressor device for the brake.

6.7.1 Behavior in standard operation
The behavior of the servo amplifier always depends on the current setting of a number of
different parameters (e.g., ACTFAULT, VBUSMIN, VELO, STOPMODE, etc.; see online
help). The diagram below illustrates the correct functional sequence for switching the
servo amplifier on and off.
DC-BUS link
Motor speed
Power stage
Enable (internal)
Devices which are equipped with a selected “Brake” function use a special sequence for
switching off the output stage (ð p.21).

6.7.2 Behavior in the event of an error (with standard setting)
The behavior of the servo amplifier always depends on the current setting of a number of
different parameters (e.g., ACTFAULT, VBUSMIN, VELO, STOPMODE, etc.; see online
help). The diagram shows the startup procedure and the procedure that the internal con-
trol system follows in the event of one or more electrical supply phases failing, assuming
that the standard parameter settings apply.
(F16/F19 = error messages Mains BTB /input phase, F05 = error message Undervoltage)
Even if there is no intervention from an external control system (in the example, the
ENABLE signal remains active), the motor is immediately braked using the emergency
stop ramp if an input phase error is detected and assuming that no changes have been
made to the factory setting (ACTFAULT=1).

6.8 Stop / Emergency Stop Function to EN 60204

6.8.1 Stop: Standards
The Stop function is used to shut down the machine in normal operation. The Stop func-
tions are defined by EN 60204 (VDE 0113), paragraphs 9.2.2 and 9.2.5.3.
Category 0: Shut-down by immediate switching-off of the energy supply to the
drive machinery (i.e. an uncontrolled shut-down);
Category 1: A controlled shut-down , whereby the energy supply to the drive
machinery is maintained to perform the shut-down, and the energy
supply is only interrupted when the shut-down has been completed;
Category 2: A controlled shut-down, whereby the energy supply to the drive
machinery is maintained.
The parameters “STOPMODE” and “ACTFAULT” must be set to 1 in order to

implement the stop categories. If necessary, change the parameters via the
terminal screen of the setup software and store the data in the EEPROM.
The Stop Category must be determined by a risk evaluation of the machine. In addition,
suitable means must be provided to guarantee a reliable shut-down.
Category 0 and Category 1 Stops must be operable independently of the operating mode,
whereby a Category 0 Stop must have priority. Stop functions must be implemented by
disconnection of the appropriate circuitry, and have priority over assigned start func-
tions.
If necessary, provision must be made for the connection of protective devices and
lock-outs. If applicable, the Stop function must signal its status to the control logic. A reset
of the Stop function must not create a hazardous situation.

6.8.2 Emergency Stop: Standards
The emergency Stop function is used for the fastest possible shut-down of the machine
in a dangerous situation. The Emergency Stop function can be triggered by the actions of
a single person. It must be fully functional and available at all times. The user must not
have to work out how to operate this mechanism. The Emergency Stop function is
defined by EN 60204 (VDE 0113), paragraph 9.2.5.4.
In addition to the requirements for Stop, the emergency Stop must fulfil the following
requirements:
l emergency stop must have priority over all other functions and controls in all opera-
ting situations.
l the energy supply to any drive machinery that could cause dangerous situations
must be switched off as fast as possible, without causing any further hazards (e.g. by
using mechanical latching devices that do not require an external supply of energy,
by counter-current braking in Stop Category 1).
l the reset must not initiate a restart.
If necessary, provision must be made for the additional connection of emergency stop
devices (see EN 60204, "Requirements for emergency stop devices"). The Emergency
Stop must be effective as a stop of either Category 0 or Category 1.
The Emergency Stop Category must be determined by a risk evaluation of the machine.
Category 0
Only hard-wired, electromechanical components may be used for the Category 0 Emer-
gency Stop function. It must not be triggered using switching logic (hardware or software),
by transferring commands via a communication network, or via a data link.
The drive must be shut down using an electromechanical circuit. If the connected servo
motor has an integrated brake, this must always be controlled by an electromechanical
circuit as well.
Category 1
With the Category 1 Emergency Stop function, there must be absolute certainty in terms
of the power supply for the machine drives being switched off (i.e., secured) using elec-
tromechanical components. Additional Emergency Stop equipment may be connected.
Bringing the motor to a standstill by interrupting the mains supply and using controlled
electronic braking. The 24 V supply for the servo amplifier must remain constant. The
issue of which circuit should be used is highly dependent on the requirements of the
application at hand.
Usually a brake in a servo motor only has the function of a holding brake. To ensure an
emergency stop function, the braking torque that is required must be checked. If the hold-
ing brake fulfills the dynamic requirements, it must be taken into acount that this applica-
tion will cause increased wear.
The parameters “STOPMODE” and “ACTFAULT” must be set to 1 in order to

implement the stop categories. If necessary, change the parameters via the
terminal screen of the setup software and store the data in the EEPROM.

6.8.3 Implementation of the Stop Category 0
Bringing the motor to a standstill by immediately switching off the amplifier power supply
(STOPMODE & ACTFAULT parameters set to 1). The switching sequence is unambig-
uously fixed by the circuit, and must be followed, to prevent undesirable error signals and
failure of the servo amplifier.
It is not possible to achieve a Category 0 shut-down with the servo amplifier alone, since
hard-wired electromechanical components are compulsory for this type of disconnection.
A brake that is built into the motor must have an additional electromechanical control cir-
cuit, as well as the control through the AX25xx, in order to meet Category 0.
Normally, a brake in a servo motor only has the function of a holding brake. To ensure an
emergency stop function, the braking torque that is required must be checked. If the hold-
ing brake fulfills the dynamic requirements, it must be taken into acount that this applica-
tion will cause increased wear.
Circuit suggestion
(with EMERGENCY STOP Category 0, control function with contactor relays)
AX2500

Bringing the motor to a standstill by interrupting the mains supply and using controlled
electronic braking (STOPMODE & ACTFAULT parameters set to 1). The 24 V supply
for the AX2500 must remain constant.
The drive is braked in a controlled manner during the stopping (disabling) procedure. If
the speed VEL0 (see sequence diagram in chapter 6.4) is undershot, the holding brake is
applied and the output stage is disabled.
As soon as two separate time periods (set at the time relay) have elapsed, the mains sup-
ply and the holding brake are electrically isolated.
Should an internal AX2500 fault occur, the motor is forced to a standstill once K20
drops out.
Circuit suggestion
AX2500

The machine receives an operational stop (disable) command and brakes the drive using
the set braking ramp (STOPMODE & ACTFAULT parameters set to 1).
The drive is braked in a controlled manner during the stopping (disabling) procedure. If
the speed VEL0 (see sequence diagram in chapter 6.4) is undershot, the holding brake is
applied and the output stage is disabled. In this case, there is no interruption of the elec-
trical supply.
If the electrical supply is switched off, not only will the controlled braking procedure be
performed, but the mains supply and the holding brake will also be electrically isolated fol-
lowing a time period set at the time relay.
Circuit suggestion
AX2500

6.9 Shock-hazard protection

6.9.1 Leakage current
Leakage current via the PE conductor results from the combination of equipment and
cable leakage currents. The leakage current frequency pattern comprises a number of
frequencies, whereby the residual-current circuit breakers definitively evaluate the 50Hz
current. For this reason, the leakage current cannot be measured using a conventional
multimeter.
As a rule of thumb, the following assumption can be made for leakage current on our
low-capacity cables at a mains voltage of 400 V, depending on the clock frequency of the
output stage:
Ileak = n x 20mA + L x 1mA/m at 8kHz clock frequency at the output stage
Ileak = n x 20mA + L x 2mA/m at a 16kHz clock frequency at the output stage
(where Ileak=leakage current, n=number of amplifiers, L=length of motor cable)
At other mains voltage ratings, the leakage current varies in proportion to the voltage.
Example: 2 x servo amplifiers + a 25m motor cable at a clock frequency of 8kHz:
2 x 20mA + 25m x 1mA/m = 65mA leakage current.
Since the leakage current to PE is more than 3.5 mA, in compliance with EN50178
the PE connection must either be doubled or a connecting cable with a
cross-section >10mm² must be used. Use the PE terminal X0/3 and the PE bolt in
order to fulfil this requirement.
The following measures can be used to minimise leakage currents.

— Reduce the length of the engine cable
— Use low-capacity cables (see p.41)
— Remove external EMC filters (radio-interference suppressors are integrated)
6.9.2 Residual-current circuit breakers (FI)
In conformity with DIN IEC 60364-4-41 – Regulations for installation and EN 60204 –
Electrical equipment of machinery, residual-current circuit-breakers (called FI below) can
be used provided the requisite regulations are complied with.
The AX2500 is a 3-phase system with a B6 bridge. Therefore, FIs which are sensitive
to all currents must be used in order to detect any D.C. fault current. Refer to chapter
6.9.1 for the rule of thumb for determining the leakage current.
Rated residual currents in the FI
Protection against "indirect contact" (personal fire protection) for stationary
10 -30 mA
and mobile equipment, as well as for "direct contact".
Protection against "indirect contact" (personal fire protection) for stationary
50 -300 mA
equipment
Recommendation: In order to protect against direct contact (with motor cables

shorter than 5 m) we recommend that each servo amplifier be protected
individually using a 30mA residual-current circuit-breaker which is sensitive to all
currents.
If you use a selective FI circuit-breaker, the more intelligent evaluation process will pre-
vent spurious tripping of the circuit-breakers.

6.9.3 Isolating transformers
If protection against indirect contact is absolutely essential despite a higher leakage cur-
rent, or if an alternative form of shock-hazard protection is sought, the AX2500 can also
be operated via an isolating transformer.
A ground-leakage monitor can be used to monitor for short circuits.
We would advise you to keep the length of wiring between the transformer and the
servo amplifier as short as possible.

BECKHOFF 06/2007 Mechanical Installation
7 Mechanical Installation
7.1 Important notes
l Protect the servo amplifier from impermissible stresses. In particular, do not let any
components become bent or any insulation distances altered during transport and
handling. Avoid contact with electronic components and contacts.
l Ensure that there is an adequate flow of cool, filtered air into the bottom of the control
cabinet or use heat exchanger. Note the conditions on page 20.
l Take care that the servo amplifier and motor are properly earthed. Do not use pain-
ted (non-conductive) mounting plates.
l Don't mount devices, which produce magnetic fields, directly beside the servo ampli-
fier. Strong magnetic fields could directly affect internal components. Install devices
which produce magnetic field with distance to the servo amplifiers and/or shield the
magnetic fields.
7.2 Guide to mechanical installation

The following notes should assist you to carry out the mechanical installation in a sensi-
ble sequence, without overlooking anything important:
In a closed control cabinet. Observe page 20.

Site The site must be free from conductive or corrosive materials.
For the mounting position within the cabinet ð p.34
Check that the ventilation of the servo amplifier is unimpeded

and keep within the permitted ambient temperature ð p.20 .
Ventilation
Keep the required space clear above and below the
servo amplifier ð p.34.
Mount the servo amplifier on mounting rails (DIN-rails) on the

Mounting conductive, earthed mounting plate in the control cabinet and
mount the necessary add-on fans (ð p.36)
EMC-conform shielding and grounding (ð p.45) Earth the moun-

Grounding,
ting plate, motor housing and CNC-GND of the controls. Notes
Shielding
on connection techniques are on page 40

Mechanical Installation 06/2007 BECKHOFF
7.3 Mounting
Material: 2 mounting rails to EN60715, min. length = system width + 40mm,
make sure there is a conductive connection to the mounting plate
Mount the protective cover (7mm) on the left side of the system.
Tools required: Screwdriver with approx. 5 mm blade width
AX2500

BECKHOFF 06/2007 Mechanical Installation
7.4 Dimensions
AX250x and AX251x
AX252x

Mechanical Installation 06/2007 BECKHOFF
7.5 Add-on fan

Electrical add-on fan for two axes to achieve rated power even under unfavourable ambi-
ent conditions, required for AX25x6.
To mount the fan, just hook it in the designated slots at the bottom of the AX2500 and
screw the fixing bolt into the thread in the housing. The electrical connection takes place
automatically when mounting the fan.
Please consider that a mounted fan increases the required space underneath the
amplifier! (Þ p. 34)
The drawing below shows, how the fan should be mounted. With an odd number of axes
(master included), the fan must also cover the power supply unit at the master.
Single master Master with 1 Axis module Master with 2 Axis modules

BECKHOFF 06/2007 Electrical Installation
8 Electrical Installation
8.1 Important notes
l Check the combination of servo amplifier and motor. Compare the rated voltage and
current of the units. Carry out the wiring according to the instructions on page 39.
l Make sure that the maximum permissible rated voltage at the terminals for L1, L2, L3
and +RBext, –DC is not exceeded by more than 10%, even in the most unfavourable
conditions (see EN 60204-1 Section 4.3.1). An excessive voltage on these terminals
can lead to destruction of the regen circuit and the servo amplifier.
Use the AX251x only on an earthed 3-phase supply system. Use the amplifier only to
drive a synchronous servomotor.
l The fusing of the AC supply input and the 24V supply is installed by the user
(ð p.19).
l Route power and control cables separately. We recommend a separation of at least
20 cm. This improves the interference immunity required by EMC regulations. If a
motor power cable is used which includes cores for brake control, the brake control
cores must be separately shielded. Earth the shielding at both ends (ð p.45).
l Install all heavy-current cables with an adequate cross-section, as per EN 60204-1
(ð p.20) and use the requested cable material (ð p. 41) to reach max. cable length.
l Wire the BTB/RTO contact in series into the safety circuit of the installation.
Only in this way is the monitoring of the servo amplifier assured.
l Install all shielding with large area (low impedance) connections, with metallised con-
nector housings or shield connection clamps where possible.
Notes on connection techniques can be found on page 40.
l It is permissible to alter the servo amplifier settings by using the operator software.
Any other alterations will invalidate the warranty.
Caution
Never disconnect the electrical connections to the servo amplifier while it is live.
Residual charges in the capacitors can have dangerous levels up to 300 seconds
after switching off the mains supply voltage. Measure the voltage in the DC Bus
link (+RBext/-DC) and wait until the voltage has fallen below 40V.
Control and power connections can still be live, even when the motor is not
rotating.

Electrical Installation 06/2007 BECKHOFF
8.2 Guide to electrical installation

The following notes should assist you to carry out the electrical installation in a sensible
sequence, without overlooking anything important:
Cable selection Select cables according to EN 60204-1, ð p.20
EMC-conform shielding and grounding (ð p.45) Earth the moun-

Grounding,
ting plate, motor housing and CNC-GND of the controls. Notes
Shielding
on connection techniques are on page 40
Wiring — Route power leads separately from control cables

— Wire the BTB/RTO contact in series into the safety loop
— Connect the digital control inputs to the servo amplifier
— Connect up AGND
— Connect the analog setpoint, if required
— Connect the feedback unit (resolver or encoder)
— If required, connect the encoder emulation
— If required, connect the fieldbus
— Connect the motor cable
Connect shielding to EMC connectors at the motor end, and
the shielding lug at the amplifier end
— Connect motor-holding brake, with shielding to EMC
connector at the motor end, and to shielding lug at the
amplifier end
— If required, connect the external regen resistor (with fusing)
— Connect the auxiliary supply
(maximum permissible voltages ð p.20)
— Connect main power supply
(maximum permissible voltages ð p.20)
— Connect PC (ð p.67).
Make a final check of the wiring carried out against the wiring
Check
diagrams that have been used

8.3 Wiring
8.3.1 Important notes
Only professional staff who are qualified in electrical engineering are allowed to
install the servo amplifier.
The installation procedure is described as an example. A different procedure may be
appropriate or necessary, depending on the application of the equipment.
We provide further know-how through training courses (on request).
Caution !
Only install and wire up the equipment when it is not live, i.e. when neither the
mains power supply nor the 24 V auxiliary voltage nor the operating voltages of
any other connected equipment is switched on.
Take care that the cabinet is safely disconnected (lock-out, warning signs etc.).
The individual voltages will be switched on for the first time during commissioning.
The ground symbol X , which you will find in all the wiring diagrams, indicates
that you must take care to provide an electrically conductive connection with the
largest possible area between the unit indicated and the mounting plate in the
control cabinet. This connection is for the effective grounding of HF interference,
and must not be confused with the PE symbol W (protective earth to EN 60204).
Use the following wiring and connection diagrams :

Overview:
Master module : Page 45
Axis module : Page 46
Mains power : Page 47
Motor : Page 48
Feedback : Page 49ff
Electronic Gearing / Master Slave
Master/slave : Page 56
Pulse/direction : Page 59
Encoder emulation:
ROD (A quad B) : Page 61
SSI : Page 62
Digital&Analog I/Os : Page 63ff
RS232 / PC : Page 67
Fieldbus:
CAN interface : Page 68
PROFIBUS interface : Page 69
SERCOS interface : Page 70
EtherCAT interface : Page 71
Multiaxis systems : Page 87

8.3.2 Shield connection on the front panel
The pre-assembled cables for

AX2500 are provided with an over-
all metal ferrule at the amplifier end
that is electrically
connected to the shielding.
Thread a cable tie through each slot

in the shielding strip (front panel) of
the servo amplifier.
00
X25
A
Tighten up the cable ties so that the
shielding ferrule and the sheathing
of the cable is pressed down tightly
against the shielding strip.
00
X25
A

8.3.3 Requirements to cables
Further information on the chemical, mechanical and electrical characteristics of the

cables can be obtained from our customer support.
Observe the restrictions in the chapter "Conductor cross-sections" on page 20.

To operate the amplifier with the max. permitted cable length, you must use cable
material which meets the requirements on the capacity given below.
Insulation material
Sheathing PUR (polyurethane, code 11Y)
Core insulation PETP (polyesteraphthalate, code 12Y)
Capacitance
Motor cable less than 150 pF/m
RES/encoder cable less than 120 pF/m

8.4 Components of a servo system
PC
Control / PLC
24V supply
fuses
drive
contactor
terminals
motor

8.5 Block diagram

The block diagram below just provides an overview.

8.6 Connector assignments

8.7 Connection diagram AX250x and AX251x (overview)
Follow the safety instructions (ð p.9)

and the use as directed (ð p.10) !
AX250x/AX251x
ðp.51ff
ð p.63
ð p.63
ð p.50
ð p.65
ð p.48
ð p.66
ð p.56 ð p.47
ð p.48
ð p.68
ð p.47
ð p.67

8.8 Connection diagram AX252x (overview)

and the use as directed (ð p.10) ! AX252x
ðp.51ff
ð p.63
ð p.63
ð p.50
ð p.65
ð p.48
ð p.56
ð p.68

8.9 Power supply, master only

8.9.1 Mains supply connection (X0)
Three-phase supplies
Directly to earthed supply, filter is integrated, fusing (e.g. fusible cut-outs) to be provided
by the user (ð p.19).
AX2500
for AX250x
for AX251x
Single-phase supplies
Directly to supply, filter is integrated, fusing (e.g. fusible cut-outs) to be provided by the
user (ð p.19).
AX2500
for AX250x
8.9.2 24V auxiliary voltage (X0)
— Electrically isolated supply from an external 24 V DC PSU, e.g. with isolating

transformer
— Required current rating (ð p.19)
Observe summarized current and voltage drop!
— Integrated EMC filter for the 24 V auxiliary supply
AX2500

8.10 DC Bus link (X0)

Can be connected in parallel with further, identical masters (via terminals -DC and RBext).
Only servo amplifiers with mains supply from the same mains (identical mains
supply voltage) may be connected by the DC bus link.
The sum of the rated currents for all of the servo amplifiers connected in parallel
to an AX2500 must not exceed 24 A.
Use unshielded single cores (2.5mm²) with a max. length of 200 mm. Use shielded
cables for longer lengths.
8.11 Motor connection with brake (X6)

Max. admisible length of the motor cable is 25 m.
AX2500
8.12 External regen resistor (X0), master only

Remove the plug-on link between terminals X0/5 (-RB) and X0/4 (+Rbint).
AX2500

8.13 Feedback
Every closed servo system will normally require at least one feedback device for sending
actual values from the motor to the servo drive. Depending on the type of feedback
device used, information will be fed back to the servo amplifier using digital or analog
means.
AX2500 supports the most common types of feedback device whose functions must be
assigned with the parameters
FBTYPE (screen page FEEDBACK), primary Feedback
EXTPOS (screen page POSITION), secondary Feedback
GEARMODE (screen page GEARING), secondary Feedback
in the setup software. Scaling and other settings must always be made here.
ASCII Commu- Speed Position- electr.

Configuration Location
Parameter tation control control gearing
One Feedback motor FBTYPE X X X
motor FBTYPE X X
Two Feedbacks EXTPOS X
externally
GEARMODE X
For a detailed description of the ASCII parameters, please refer to the online help of the
setup software.
The table below provides an overview of the supported feedback types, their correspond-
ing parameters and a reference to the relevant connection diagram in each case. On
each of these, the pin assignment shown on the encoder side relates to the BECKHOFF
motors.
Wiring
Primary feedback type Connector FBTYPE
diagram
Resolver X5 ð S.50 0, 3
SinCos Encoder BISS X2 ð S.51 20*
SinCos Encoder ENDAT X2 ð S.52 3, 4
SinCos Encoder HIPERFACE X2 ð S.52 2, 3
SinCos Encoder w/o data channel X2 ð S.53 6, 7 (16*)
SinCos Encoder + Hall X2 ð S.54 11*
RS422 5V X4 ð S.55 8*, 9*
Sensorless (w/o feedback) - - 10*
* Can only be set on the terminal screen of the setup software
** RS422 means “incremental encoder AquadB”.
Hints for combining primary with secondary feedback systems for position
control/electr. gearing can be found from page 56.

8.13.1 Resolver (X5)
Connection of a Resolver (2 to 36-poles) as a feedback system. The thermostat contact

in the motor is connected via the resolver cable to the AX2500 and evaluated there.
If lead lengths of more than 25 m are planned, please consult our customer support.
FBTYPE: 0, 3
AX2500 SubD9 12-pin round

8.13.2 Sine encoder 5V with BISS (X2)
Connection of a single- or multiturn sine-cosine encoder (5V) with BISS interface as feed-
back (from firmware revision 6.68). During start-up of the servo amplifier the parameters
stored in the encoder eeprom are uploaded, after that phase only the sine/cosine signals
are used.
The thermostat contact in the motor is connected via the encoder cable to X2 and
evaluated there. All signals are connected using our pre-assembled encoder connection
cable.
If cable lengths of more than 50m are planned, please consult our customer service.
Frequency limit (sin, cos): 350 kHz
FBTYPE: 20
AX2500

8.13.3 Sine Encoder with EnDat 2.1 or HIPERFACE (X2)
Connection of a single-turn or multiturn sine-cosine encoder. Preferred types are the

ECN1313 and EQN1325 encoders.
The thermostat contact in the motor must be connected via the encoder cable to the
AX2500 and evaluated there. All signals are connected using our pre-assembled encoder
connection cable.
If lead lengths of more than 25 m are planned, please consult our customer support.
Encoder with EnDat: FBTYPE 3, 4
Encoder with HIPERFACE: FBTYPE 2, 3
AX2500 SubD15 17-pin round

8.13.4 Sine Encoder without data channel (X2)
Connection of a sine-cosine encoder without data channel as feedback. Every time the
24V auxiliary voltage is switched on, the amplifier needs start-up information for the posi-
tion controller (parameter value MPHASE). Depending on the feedback type either
wake&shake is executed or the value for MPHASE is read out of the amplifier's
EEPROM.
The thermostat contact in the motor must be connected via the encoder cable to X2 and
evaluated there.
If lead lengths of more than 50 m are planned, please consult our customer service.
Encoder type FBTYPE Remarks

SinCos 5V 6 MPHASE from EEPROM
SinCos 5V 7 MPHASE with wake & shake
Commutation with resolver,
Resolver+SinCos5V 16
Speed&Position with Encoder
Don't use this feedback type with vertical load (hanging load).
AX2500 SubD 15

8.13.5 Incremental or sine encoder with hall sensors (X2)
Feedback devices (incremental or sine-cosine), which don't deliver an absolute informa-

tion for commutation, can be used as complete feedback system combined with an addi-
tional Hall encoder. All signals are connected to X2.
If cable lengths of more than 25 m are planned, please consult our customer service.
Frequency limit (A, B): 350 kHz
RS422 with Hall: FBTYPE 12
Encoder with Hall: FBTYPE 11
AX2500 SubD15

8.13.6 Incremental Encoder (X4)
An incremental encoder can be used as standard motor feedback.

Every time the 24V auxiliary voltage is switched on, the amplifier needs start-up informa-
tion for the position controller (parameter value MPHASE). Depending on the feedback
type either wake&shake is executed or the value for MPHASE is read out of the ampli-
fier's EEPROM.
The thermostat contact in the motor must be connected to X2 (see p.52) or X5 (see p.50).
If lead lengths of more than 50 m are planned and for questions concerning the power
supply of the encoder, please consult our customer service.
Frequency limit (A, B): 1.5 MHz
Encoder type FBTYPE Remarks

RS422 5V 9 MPHASE from EEPROM
RS422 5V 8 MPHASE with wake & shake
Don't use this feedback type with vertical load (hanging load).
AX2500 SubD 9

8.14 Electronic Gearing, Master-slave operation

In the case of the “electronic gearing” functionality (see setup software and description of
GEARMODE parameter), the servo amplifier is controlled by a secondary feedback
device as a slave.
It is possible to set up master/slave systems, use an external encoder as a setpoint
encoder or connect the amplifier to a stepper motor control.
The amplifier is parameterized using the setup software (electronic gearing).
Primary Feedback: adjust on screen page "Feedback" (FBTYPE)
Secondary Feedback: adjust on screen pages "Position" and "Gearing" (EXTPOS,
GEARMODE)
Master-/Slave adjustment
Master: adjust encoder emulation on screen page "ROD/SSI/Encoder" (ENCMODE)
Slave: adjust on screen pages "Position" and "Gearing" (EXTPOS, GEARMODE)
The following types of external encoder can be used:
Wiring
secondary Feedback type Connector GEARMODE
diagram
Incremental Encoder 5V X4 ð p.57 3, 5*, 13*, 15*
Incremental Encoder 24V X3 ð p.57 0, 2*, 10*, 12*
Sine/Cosine Encoder X2 ð p.58 6, 8*, 9*, 16*
SSI Encoder X4 ð p.59 7*, 17*
Pulse and Direction 5V X4 ð p.60 4, 14*
Pulse and Direction 24V X3 ð p.60 1, 11*
* adjustable via terminal screen of the setup software
The following table shows the allowed feedback combinations:

Secondary Feedback for Position control/Following
Primary Sine Encoder Increm. Encoder Pulse&Direct. SSI Encoder
Feedback (X2) 5V/24V (X4/X3) 5V/24V (X4/X3) (X4)
EXTPOS= 1,2,3 EXTPOS= 1,2,3 EXTPOS= 1,2,3 EXTPOS= 1,2,3
Resolver (X5) GEARMODE= GEARMODE= GEARMODE= GEARMODE=
FBTYPE= 0 6,8,9,16 0,2,3,5,10,12,13,15 1,4,11,14 7,17
FPGA= 0 FPGA= 0 FPGA= 0 FPGA= 1
ENCMODE= 0 ENCMODE= 0 ENCMODE= 0 ENCMODE= 2
EXTPOS= 1,2,3 EXTPOS= 1,2,3 EXTPOS= 1,2,3
Sine Encoder
GEARMODE= GEARMODE= GEARMODE=
(X2)
- 0,2,3,5,10,12,13,15 1,4,11,14 7,17
FBTYPE=
FPGA= 1 FPGA= 1 FPGA= 1
2,4,6,7,20
ENCMODE= 0 ENCMODE= 0 ENCMODE= 2
EXTPOS= 1,2,3 EXTPOS= 1,2,3
Encoder & Hall
GEARMODE= GEARMODE=
(X2)
- 0,2,3,5,10,12,13,15 1,4,11,14 -
FBTYPE= 11,12
FPGA= 1 FPGA= 1
ENCMODE= 0 ENCMODE= 0
RS422 Encoder
(X4) - - - -
FBTYPE= 8,9
EXTPOS= 1,2,3 EXTPOS= 1,2,3 EXTPOS= 1,2,3
Sensorless GEARMODE= GEARMODE= GEARMODE=
FBTYPE= 10 - 0,2,3,5,10,12,13,15 1,4,11,14 7,17
FPGA= 0 FPGA= 0 FPGA= 1
ENCMODE= 0 ENCMODE= 0 ENCMODE= 2

8.14.1 Connection to a AX2500 master, 5 V signal level (X4)
You can link several AX2500 amplifiers in master-slave operation (encoder follower).
Up to 16 slave amplifiers can be controller by the master via the encoder output. The
SubD connector X4 is used for this purpose.
Frequency limit: 1 MHz, transition speed tv £ 0.1 µsec
AGND (terminal X3/1) must be connected to the ground of the control system!
AX2500 AX2500
8.14.2 Connection to incremental encoder master with 24 V signal level (X3)
You can use this interface to set up the AX2500 as a slave following an encoder with a
24V signal level (master-slave operation). This application uses the digital inputs DIGI-
TAL-IN 1 and 2 on connector X3.
Frequency limit: 100 kHz, transition speed tv £ 0.1 µsec
AX2500

8.14.3 Connection to a sine-cosine encoder master (X2)
You can set up the AX2500 as a slave following a sine/cosine encoder (master-slave
operation). This application uses the SubD connector X2.
If cable lengths of more than 50m are planned, please consult our customer service.
AX2500

8.14.4 Connection to a SSI encoder (X4)
You can set up the AX2500 as a slave following a synchronous serial absolute-encoder
(master-slave operation). This application uses the SubD connector X4.
If lead lengths of more than 50 m are planned and for questions concerning the power
supply of the encoder, please consult our customer service.
Frequency limit: 1 MHz
AX2500
8.14.5 Connection to stepper motor controllers (pulse and direction)
You can connect the servo amplifier to a third-party stepper-motor controller. The param-
eters for the servo amplifier are set up with the aid of the setup software (electrical gear-
ing). The number of steps can be adjusted, so that the servo amplifier can be adjusted to
the pulse/direction signals of any stepper-motor controller. Various monitoring signals can
be output.
Observe the limit frequency!

Using an A quad B encoder provides better EMC noise immunity.
Speed profile and signal diagram

8.14.5.1 Step/Direction with 5 V signal level (X4)
Connection of the servo amplifier to a stepper motor control with a 5 V signal level. The
SubD connector X4 is used for this purpose.
Frequency limit: 1 MHz
AX2500
8.14.5.2 Step/Direction with 24 V signal level (X3)
Connection of the servo amplifier to a stepper motor control with a 24 V signal level. The
digital inputs DIGITAL-IN 1 and 2 on connector X3 are used for this purpose.
Frequency limit: 100 kHz
AX2500

8.15 Encoder emulations

8.15.1 Incremental encoder output - A quad B (X4)
The incremental-encoder interface is part of the package supplied. Select the encoder
function ROD (screen page “Encoder”, funktion ENCMODE). In the servo amplifier, the
position of the motor shaft is calculated from the cyclic-absolute signals of the resolver or
encoder.
Incremental-encoder compatible pulses are generated from this information. Pulses are
output as two signals, A and B, with 90° phase difference and a zero pulse. The resolu-
tion (lines before quadrature) can be changed with the RESOLUTION parameter:
Encoder function Feedback system Resolution Zero position

one per revolution
Resolver 256...4096
(only if A=B=1)
ROD (1)
256...524288 one per revolution
Encoder
(28 ... 219) (only if A=B=1)
22...27 TTL analog pass
ROD interpolation (3) Encoder
lines per sine line through X2 to X4
You can also adjust and store the position of the zero pulse within one mechanical turn
(parameter NI-OFFSET). The ground reference for the interface is PGND.
PGND must always be connected to the control ground. The max. admissible cable
length is 10 m.
Connections and signal description for the incremental-encoder interface :

The count direction is UP when the motor shaft is rotating clockwise (looking at the end of
the motor shaft).
AX2500

8.15.2 SSI output (X4)
The SSI interface (synchronous serial absolute-encoder emulation) is part of the package
supplied. Select encoder function ROD (“Encoder” screen page).
The servo amplifier calculates the motor shaft position from the cyclic-absolute signals of
the resolver or encoder. From this information a SSI date (after Stegmann patent specifi-
cation DE 3445617C2) is provided.
28 bits are transferred. The 12 leading data bits contains the number of revolutions. The
following max. 16 bits contain the resolution and are not variable.
The following table shows the allocation of the SSI date:
Revolution Resolution
11 10 9 8 7 6 5 4 3 2 1 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
The signal sequence can be output in Gray code or in Binary (standard) code (parameter
SSI-CODE). The servo amplifier can be adjusted to the clock frequency of your SSI-eval-
uation through the SSI-TIMEOUT parameter (cycle time 1.3 µs or 10 µs).
The ground reference for the interface is PGND.
PGND must always be connected to the control ground.
Connection and signals for the SSI interface :

The count direction is UP when the motor shaft is rotating clockwise (looking at the end of
the motor shaft).
AX2500

8.16 Digital and analog inputs and outputs

8.16.1 Analog input (X3)
The servo amplifier has a programmable input for analog setpoints.

AGND (X3/1) must always be joined to the CNC-GND of the controls to provide a ground
reference.
Technical data
— Input voltage max. ± 10 V
— Resolution 1.25 mV
— Ground reference AGND, terminal X3/1
— Input resistance 20 kW
— Common mode voltage range for both inputs ± 10 V supplementary
— Update rate: 62.5 µs
AX2500
Input Analog-IN (terminals X3/2-3)

Input voltage max. ± 10 V, 14-bit resolution, scalable
Standard setting: Speed Setpoint
Fixing the direction of rotation
Standard setting: clockwise rotation of the motor shaft (looking at shaft end)
with positive voltage on terminal X3/3 (+ ) against X3/2 ( - )
To reverse the direction of rotation you can swap the connections to terminals X3/2-3 or
change the DIRECTION parameter in the SPEED screen.

8.16.2 Digital inputs (X3)
All digital inputs are electrically isolated through optocouplers.

Technical data
— Reference ground is digital-GND (DGND, terminal X1/4,5 on the master)
— The logic is dimensioned for +24 V / 7 mA (PLC-compatible)
— H-level from +12...36 V / 7 mA, L-level from 0...7 V / 0 mA
— Update rate: Software:250 µs / Hardware: 2 µs
AX2500
You can use the digital inputs PSTOP / NSTOP / DIGITAL-IN1 and DIGITAL-IN2 to initi-
ate pre-programmed functions that are stored in the servo amplifier.
You will find a list of the pre-programmed functions in the Online Help.
If an input has to be re-assigned to a pre-programmed function, then the data set must be
stored in the EEPROM of the servo amplifier, and the 24 V auxiliary supply for the servo
amplifier must be switched off and then on again (to reset the amplifier software).
Limit-switches PSTOP / NSTOP
Terminals X3/6 and X3/7 are used to connect limit switches. They are deactivated upon
delivery. If these inputs are not needed for the connection of limit switches, then they can
be used for other input functions.
Limit-switch positive/negative (PSTOP / NSTOP, terminals X3/6 and X3/7), high level in
normal operation (fail-safe for cable break). A low signal (open) inhibits the corresponding
direction of rotation.
DIGITAL-IN 1 / DIGITAL-IN 2
You can link the digital inputs at terminals X3/4 (DIGITAL-IN 1) and X3/5 (DIGITAL-IN2)
with a pre-programmed function.

8.16.3 Digital outputs (X3)
Technical characteristics
— Ground reference is Digital-GND (DGND, terminal X1/4,5 on the master)
— Alle digital outputs are floating
— DIGITAL-OUT1 and 2 : Open-collector, max. 30 V DC, 10 mA
— Update rate: 250 µs
AX2500
Programmable digital outputs DIGITAL-OUT 1 / 2:

You can use the digital outputs DIGITAL-OUT1 (terminal X3/8) and DIGITAL-OUT2
(terminal X3/9) to output messages from pre-programmed functions that are stored in the
servo amplifier.
A list of the pre-programmed functions can be found in the Online Help.
If an input is freshly assigned to a pre-programmed function, then the data set must be
stored in the EEPROM of the servo amplifier, and the 24 V auxiliary supply of the servo
amplifier must be switched off and on again (to reset the amplifier software).

8.16.4 Digital I/O on the Master (X1)
Technical characteristics
— Ground reference is Digital-GND (DGND, terminal X1/4,5)
— The logic is dimensioned for +24 V / 7 mA (PLC-compatible)
— H-level from +12...36 V / 7 mA, L-level from 0...7 V / 0 mA
BTB/RTO: Relay output, max. 30 V DC or 42 V AC, 0.5 A
AX2500
ENABLE input
The output stage of the servo amplifier is activated by the enable signal
(terminal X1/3, input 24V, active-high).
In the inhibited state (low signal) the motor which is attached does not have any torque.
Ready-to-operate contact BTB/RTO
Operational readiness (terminals X1/1 and X1/2 ) is signalled via a floating relay contact.
The contact is closed when all servo amplifiers in the system are ready for operation.
This signal is not influenced by the enable signal, the I²t- limit, or the regen threshold.
All faults cause the BTB/RTO contact to open and the switch-off of the output
stage (if the BTB contact is open, the output stage is disabled -> no power). A list
of the error messages can be found on page 90.

8.17 RS232 interface, PC connection (X8), master only

The setting of the operating, position control, and motion-block parameters, can be car-
ried out by using the setup software on an ordinary commercial PC.
Connect the PC interface (X8) of the servo amplifier while the supply to the equipment
is switched off via a null-modem cable to a serial interface on the PC.
Do not use a null-modem link cable!
The interface has the same potential as the internal logic, and uses AGND as the ground
reference.
The interface is selected and set up in the setup software.
Further notes can be found on page 74 .
AX2500
Interface cable between the PC and servo amplifiers of the AX2500 series:
(View: front view of the built-in SubD connectors, this corresponds to looking at the solder
side of the SubD connector on the cable.)

8.18 Fieldbus connection

8.18.1 CANopen interface (X7)
The interface for connection to the CAN bus (default: 500 kbps). The master is fitted with
a CAN input. All axis modules in the system are connected to this through the internal
bus. The last axis module has a CAN output, where the CAN bus either continues to
other bus participants or is terminated by a termination resistor.
The integrated profile is based on the communication profile CANopen DS301 and the
drive profile DS402. The following functions are available in connection with the inte-
grated position controller: Jogging with variable speed, homing, start motion task, start
direct task, digital setpoint provision, data transmission functions and many others.
Detailed information can be found in the CANopen manual.
The interface is at the same potential as the internal logic, and uses AGND as the ground
reference.
AGND must be connected to the control system ground for potential equalization!
AX2500
CAN bus cable
To meet ISO 11898 you should use a bus cable with a 120 W characteristic impedance.
The maximum usable cable length for reliable communication decreases with increasing
transmission speed. As a guide, you can use the following values which we have mea-
sured, but they must not be assumed to be limits:
Cable data: Characteristic impedance 100-120 W
Cable capacitance max. 60 nF/km
Conductor loop resistance 159.8 W/km
Cable length, depending on the transmission rate
Transmission rate / kbps max. cable length / m
1000 20
500 70
250 115
Lower cable capacitance (max. 30 nF/km) and lower lead resistance (loop: 115 W/km)
make it possible to transmit over longer distances.
(Characteristic impedance 150 ± 5 W Þ terminating resistance 150 ± 5 W).
For EMC reasons, the SubD connector housing must fulfill the following conditions:
— metal or metallized housing
— provision for connecting the cable shielding within the housing,
large-area connections

8.18.2 PROFIBUS interface (X7), option
This section describes the PROFIBUS interface for AX2500.

Information on the range of functions and the software protocol can be found in the man-
ual “Communication profile PROFIBUS-DP”.
The selection of cables, cable routing, shielding, bus connectors, bus termination and
propagation times are described in the “Setup guidelines for PROFIBUS-DP/FMS” from
PNO, the PROFIBUS User Organization.
AX2500
Use only identical cable types of one manufacturer.
Recommendations for 1.5 MBit/s and 3 MBit/s
1.5 MBit/s max 32 axes per segment

3 MBit/s max 32 axes per segment
Recommendations for 6 MBit/s and 12 MBit/s

8 x AX2500
For long-term reliability of the system
with 6 MBit/s and 12 MBit/s we
recommend to connect the segments
with repeaters and to use one
AX2500-Master per segment only
(see example).
6 x AX2500
max 8 axes(1 master) per

6 MBit/s
Master
segment
max 8 axes(1 master) per
12 MBit/s
segment
4 x AX2500

8.18.3 SERCOS interface (X7), option
This section describes the SERCOS interface of the AX2500. Information on the range of
functions and the software protocol can be found in the manual “IDN Reference Guide
SERCOS”.
For the fiber optic cable connection, only use SERCOS components to the SERCOS
Standard IEC 61491.
8.18.3.1 Light emitting diodes (LEDs)
Indicates whether SERCOS telegrams are being correctly received. In the final
RT Communication Phase 4 this LED should flicker, since cyclical telegrams are
being received.
Indicates that SERCOS telegrams are being transmitted. In the final Communi-
cation Phase 4 this LED should flicker, since cyclical telegrams are being trans-
TT mitted. Check the stations addresses for the controls and the servo amplifier if:
- the LED never lights up in SERCOS Phase 1 or
- the axis cannot be operated, although the RT LED is lighting up cyclically.
Indicates that SERCOS communication is faulty or suffering from interference.
If this LED is very bright, then communication is suffering strong interference, or
is non-existent. Check the SERCOS transmission speed for the controls and the
servo amplifier (BAUDRATE) and the fibre-optic connection.
If this LED flickers, this indicates a low level of interference for SERCOS com-
Err
munication, or the optical transmitting power is not correctly adjusted to suit the
length of cable. Check the transmitting power of the (physically) previous SER-
COS station. The transmitting power of the servo amplifier can be adjusted in
the setup software DRIVE.EXE on the SERCOS screen page, by altering the
parameter for the cable length.
8.18.3.2 Connection diagram
Layout of the SERCOS bus system in ring topology, with optical fibre cables (schematic).

8.18.4 EtherCat interface (X7), option
This section describes the EtherCat interface of the AX2500. Information on the range of
functions and the software protocol can be found in the EtherCat documentation (actually
in process).
8.18.4.1 EtherCat connection, connector X7A/B (RJ-45)
Connection to the EtherCat network with RJ-45 connectors (IN and OUT interfaces).
8.18.4.2 Connection diagram


BECKHOFF 06/2007 Setup
9 Setup
9.1 Important notes
Only professional personnel with extensive knowledge in the fields of electrical
engineering and drive technology are allowed to setup the servo amplifier.
The procedure for commissioning is described as an example. Depending on the applica-

tion, a different procedure may be appropriate or necessary. In multi-axis systems, com-
mission each servo amplifier individually.
Before setting up, the manufacturer of the machine must produce a hazard
analysis for the machine and take appropriate measures to ensure that unforeseen
movements do not result in personal injury or material damage.
Check that all connection components that are live in operation are safely
protected against bodily contact. The equipment produces potentially lethal
voltages up to 800 V.
Never undo the electrical connections to the servo amplifier while it is live.
Capacitors can still have dangerous residual charges up to 300 seconds after
switching off the supply voltage.
The heat sink and front panel of the amplifier can reach temperatures up to 80°C in
operation. Check the heat sink temperature. Wait until the heat sink has cooled
down to 40°C before touching it
If the servo amplifier has been stored for longer than 1 year, then the DC Bus link
capacitors will have to be re-formed.
To do this, disconnect all the electrical connections.
Supply the servo amplifier for about 30 min. from single-phase 230 V AC to the
terminals L1 / L2. This will re-form the capacitors.
Further information on commissioning:

The adaptation of parameters and their effects on the control loop behaviour are
described in the online help of the setup software.
The commissioning of the fieldbus interface is described in the corresponding
manual.
We can provide further know-how through training courses (on request).

Setup 06/2007 BECKHOFF
9.2 Setup software

9.2.1 General
This chapter describes the installation of the setup software DRIVE.EXE for the AX2500
digital servo amplifiers.
We offer training and familiarization courses on request.
9.2.1.1 Use as directed
The operator software is intended to be used for altering and storing the operating param-
eters for the AX2500 series of servo amplifiers. The attached servo amplifier is commis-
sioned with the assistance of the software - during this process the drive can be con-
trolled directly by the service functions.
Only professional personnel who have the relevant expertise described on page 7
are permitted to carry out online parameter setting for a drive which is running.
Sets of data which are stored on data media are not safe against unintended
alteration by other persons. After loading a set of data you must therefore check all
parameters thoroughly before enabling the servo amplifier.
9.2.1.2 Software description
The servo amplifiers must be adapted to the requirements of your installation. Usually you
will not have to carry out this parameter setting yourself on the amplifier, but on a PC,
with the assistance of the operator software. The PC is connected to the servo amplifier
by a null-modem (serial, ð p.67) cable. The setup software provides the communication
between the PC and AX2500.
You will find the setup software on the accompanying CD-ROM and in the download sec-
tion of our website.
With very little effort you can alter parameters and immediately observe the effect on the
drive, since there is a continuous (online) connection to the amplifier. At the same time,
important actual values are read out from the amplifier and displayed on the PC monitor
(oscilloscope function).
Any interface modules which may be built into the amplifier are automatically recognized,
and the additional parameters which are required for position control or motion-block defi-
nition are made available.
Sets of data can be stored on data media (archived) and loaded again. You can also print
out the data sets.
We provide you with motor-specific default sets of data for all the reasonable combina-
tions of servo amplifier and motor. In most applications you will be able to use these
default values to get your drive running without any problems.
An extensive online help with integrated description of all variables and functions sup-
ports you in each situation.

9.2.1.3 Hardware requirements
The PC interface (X6, RS232) of the master is connected to a serial interface on the PC
by a null-modem cable (not a null-modem link cable !) (ð p.67).
Connect / disconnect the interface cable only when the supply is switched off for
both the PC and the servo amplifier.
The interface in the servo amplifier is electrically isolated by an optocoupler, and is at the
same potential as the CANopen interface.
Minimum requirements for the PC:
Processor : Pentium I or higher
Operating system : WINDOWS 98 / 2000 / ME / NT4.0 / XP
Graphica adapter : Windows compatible, color
Drives : Hard disk (10 MB free space)
CD-ROM drive
Main memory : at least 8 MB
Interface : one free serial interface (COM1... 10)
9.2.1.4 Operating systems
WINDOWS 98 / 2000 / ME / NT / XP
DRIVE.EXE can work under WINDOWS 98 / 2000 / ME / XP or WINDOWS NT 4.0.
Emergency operation is possible with an ASCII terminal-emulation.
Interface setting: 9600 bps, databit 8, stopbit 1,no parity, no handshake
Unix, Linux
DRIVE.EXE does not work under Unix and Linux.
9.2.2 Installation under WINDOWS 98 / 2000 / ME / NT / XP
The CD-ROM includes an installation program for the setup software.

Installation
Insert the CD-ROM into a free drive.
Autostart activated:
The start screen of the CD-ROM pops up. Click on the link to the Setup Software and
follow the instructions.
Autostart deactivated:
Click on START (task bar), then on Run. Enter the program call x:\index.htm (where x is
the drive letter for the CD drive). Click on OK and then on the link to the Setup Software
and follow the instructions.
Connection to the serial interface of the PC
Connect the interface cable to a serial interface on your PC and the PC interfaces (X8) of
the AX2500 (ð p.67).

9.3 Quickstart, drive test

9.3.1 Preparation
9.3.1.1 Unpacking, Mounting and Wiring the Servo Amplifier
1. Unpack servo amplifier and accessories

2. Observe safety instructions in the manuals
3. Mount the servo amplifier as described in chapter 7.3
4. Wire the servo amplifier as described in chapter 8.3 or apply the minimum wiring for
drive testing as described in chapter 9.3.1.3
5. Install the software as described in chapter 9.2
9.3.1.2 Documents
You need access to these documents (located on the product CD-ROM, you can down-
load the latest editions from our website):
l Product Manual (this manual)
Depending on the installed fieldbus interface you need one of these documents:
l CANopen Communication Profile Manual
l PROFIBUS DP Communication Profile Manual
l SERCOS Communication Profile Manual
l EtherCat Communication Profile Manual (in process)
You need Acrobat Reader to read the PDFs, an installation link is on every screen of the
product CD-ROM.

9.3.1.3 Minimum Wiring for Drive Test
This wiring does not fulfill any requirements to safety or functionality of your
application, it just shows the required wiring for drive testing without load.
ENC
1
2
3
Enable
24V ON
PC
1 +
2
RES -
4 24V DC
5
Power ON
Motor-Power
Motor-Power
Feedback
Feedback
Motor Motor
Power

9.3.2 Connect
l Connect the interface cable to a serial interface on your PC and to the serial interface
X8 of the servo amplifier. USB to serial converter can be used optionally.
l Switch on the 24 V power supply for the servo amplifier.
l Wait about 30 seconds, until the front display of the servo amplifier displays the cur-
rent class (e.g. for 3 A) . If the power supply voltage is switched on, too, a lea-
ding P is displayed (e.g. for Power, 3 A).
If a fault code ( ) or a warning ( ) or a status message (./_ / E/S) appears

in the display, you will find the description on page 90ff. If there is fault, fix the
problem.
Double-Click the DRIVE.EXE icon on your Windows desktop to start the

software..
You can work offline or online with

"Multidrive" must be activated in the DRIVE.EXE. We work online now.
menu "Communication"! Select the interface where the servo amplifier
is connected to.
The software tries to communicate

with the drive and to upload the para-
meters. If it's not successful, you recei-
ve this error message:
- wrong interface chosen

- wrong connector chosen at the servo amplifier
Frequent causes: - interface is used by another software
- 24 V auxiliary voltage for the servo amplifier not working
- interface cable broken or wrong wiring
Click OK to remove the error message. Detect and remove the error source. Restart the
software.

If communication works, the drive selection screen appears:
The master and axis modules, recognized in the sys-

tem, with its station address and name are listed. The
master module is separately characterized.
Doubleclick on the amplifier, which you want to work
with.
You can select additional other axis modules later to
show them in parallel at the screen and parameterize
them (Multidrive function).
Now parameters are transmitted from the servoamplifier to the computer. Then you see
the start screen.
Make sure, that the amplifier is disabled (Input HW-Enable connector X1 pin 3 must
be 0 V or open)!
9.3.3 Important Screen Elements
Help Function
In der Online-Hilfe finden Sie detaillierte Informationen zu allen Parametern, die vom
Servoverstärker verarbeitet werden können.
Key F1 Starts Online Help for the actual screen page.

Menu Bar ? /
Starts Online Help with table of contents.
Online HTML Help
Tool Bar
Save to EEPROM,
required if you changed parameters.
Reset (coldstart),
required if you changed important configuration parameters.
Operation Mode, use Digital Velocity mode for drive testing.
Disable and Enable of the amplifier's output stage via soft-

ware.
Status Bar

9.3.4 Basic Setup
On the start screen click "Basic Setup" button.
Regen Resistor: Change only if you use an external regen resistor. Most applications
don't need an external regen resistor.
Max. Mains Voltage: Select the nominal mains AC voltage.
Mains Phase Missing: You can select either warning "n05" or error "F19" in case of
phase loss. The setting "F19" disables the output stage, "n05" is just a message.
Units: Acceleration, Velocity, Position
Select usable units for your application referring to the moved load.
Address:
Adjust for master amplifier only (= highest address of the drive system, see p.86)
Leave all other fields unchanged.
Click OK. On the start screen click "Motor" button.

9.3.5 Motor (synchronous)
Press function key F12 (disable) before changing motor parameters.

Motor Type: Select Synchronous Motor. If you use a linear motor or an induction motor,
please contact our support department.
Number-Name: Click the list to start uploading the motor parameter table, which is stored
in the servo amplifier. Search and select the connected motor. If your motor is not listed,
please contact our support department.
Click OK.
If your motor has a built-in brake, click

"Yes", otherwise "No".
If Software Enable is active, a warning

appears. You can proceed, but after the
amplifier is restarted, you must check
whether the holding brake configuration is
correct.
Click OK.
Parameters are uploaded to the ampli-
fier's RAM now (takes some seconds).
When this is done, you have to accept the
changed configuration with "Yes" or to
discard the changes in the appearing
screen.
If you click "Yes", the parameters are sa-
ved in the EEPROM and the amplifier
makes a coldstart (reset). This takes
some seconds.
On the start screen, click "Feedback" button.

9.3.6 Feedback
Press function key F12 (disable) before

changing feedback parameters.
Feedback Type:
Select the feedback type used.
If Software Enable is active, a warning ap-

pears. The configuration change cannot be
performed.
Click OK on the warnings, press F12 (SW
disable) and start the Feedback procedure
again.
If everything was ok, the same procedure

(parameter upload) that has been described
for the motor selection starts.
If you click "Yes", the parameters are saved
in the EEPROM and the amplifier makes a
coldstart (reset). This takes some seconds.

9.3.7 Save Parameters and Restart
You are going to finish setup and you have changed several basic parameters. Depend-
ing on the parameters you changed, two possible reactions can occur:
Configuration parameters changed
A warning appears, that you have to restart the amplifier. This is called "coldstart". Click
"YES". The parameters are saved to the amplifier's EEPROM automatically and a reset
command restarts the amplifier (takes a few seconds). For example, this happens after
motor or feedback selection.
Other parameters changed
No warning appears. Parameters are saved in the volatile RAM only.
Save the parameters to the EEPROM of the servo amplifier manually by clicking the sym-
bol in the tool bar. A coldstart of the amplifier is not necessary.
Reset the amplifier
You can reset the amplifier manually (e.g. in case of an error). Click the iconl .

9.3.8 Jogging the Motor (Speed Control)
Be aware that the actual position of the load permits the subsequent moving
operations. The axis could move to the hardware limit-switch or the mechanical
stop. Make sure that a jerk or a fast acceleration of the load cannot cause any
damage.
l Switch on the power supply for the drive.

l Hardware-Enable: +24 VDC to Enable [connector X1 pin 3].
l Software-Enable: Click the "Enable" button on the start screen or

use key combination Shift+F12. Now, the front display shows an E and the current
rating (e.g. for Enable, 3 A).
l Click the icon "Oscilloscope" :
l Select Service-Mode "Speed F6", then click "Parameter" button
l Enter a safe speed. The sign defines the direction of movement.
Observe the "safe reduced speed" requirements for your application!
l Click OK.
l Start the service function ("Start" button or press F6).
Click OK on the warning notice.
The opmode is switched to "0" and the output stage is enabled automatically.
The symbol's color changes to green as long as the function is active.

l The function is active until you click the "Stop" button or press F9.
l The output stage can be disabled by pressing function key F12.

9.3.9 Status
Actual warnings and errors are listed on the Status screen, which can be accessed on
the start screen by clicking the "Status" button. This button monitors the current status of
the amplifier and can appear with different text.
The Reset button can be used to clear some actual error messages. A description of
errors/warnings can be found on p. 90.
Now you have setup and tested the basic functions of the drive successfully.
9.3.10 Monitor
Click the icon

"Monitor"
The Monitor screen shows

all important electrical and
mechanical actual values.
9.3.11 Additional Setup Parameters
Detailed information on all setup functions can be found in the Online Help systemand
and the integrated command reference.

9.4 Multi-axis systems

All the axes in a system can be parameterized through the RS232 interface in the master.
To do this, there is an internal connection between the master and the axis modules. The
PC cable only has to be connected to the master.
The internal address assignment is carried out automatically, so that it is only necessary
to set up the basic station address for the master.
Axismodule 1
Axismodule 2
PC
Axismodule 3
Master
COMx
X8 / PC RS232
9.4.1 Station Address
Adjust the address of the master with the setup software. The addresses of the axis mod-
ules are then assigned automatically.
After changing the station address it is necessary to turn off the 24 V auxiliary
supply, and then turn it on again.
Starting at the master, descending addresses are assigned automatically to the axis mod-
ules. The following table shows an example with one master and three axis modules
according to the graphics above:
Axis Address Remark

Master 10 Master address, set by user
Axis module 3 9
Axis module 2 8 assigned automatically
Axis module 1 7
The highest permitted master address is 128. When choosing the master address,
please consider that at least address 1 will be assigned to the last (leftmost) axis
module.
In CAN and PROFIBUS field bus systems the automatically assigned addresses
must not match the address of other nodes.

9.4.2 Example of connections for multi-axis system

and the use as directed (ð p.10) !
M
AX250x / AX251x
M
AX252x
AX252x

9.5 Key pad controls and status displays

Two keys are fitted in the operating panel of the master. Here you can enter the basic
address for the system and call up status information on all the axes that are connected.
9.5.1 Operating
The two keys can be used to perform the following functions:
Key symbol Functions

press once : go up one menu item, increase number by one
press twice in rapid succession : increase number by ten
press once : go down one menu item, decrease number by one
press twice in rapid succession : decrease number by ten
press and hold right key, then press left key as well :
enters a number, return function
9.5.2 Status display on the axis module
Each axis module is fitted with 2 LEDs that provide a quick indication of the instrument
status.
LED
red green Interpretation
lit off axis is not ready for operation (fault)
blinking off a warning has been generated
off lit axis is ready for operation, and enabled
off blinking axis is ready for operation, but not enabled
blinking blinking axis is selected for editing by the master
A detailed display of the warnings and faults can be called up in the display on the master
( ð p.89).

9.5.3 Status display on the master

9.6 Error messages

Any errors that occur are shown in coded form by an error number in the LED display on
the front panel. All error messages result in the BTB/RTO contact being opened, the out-
put stage being switched off (motor loses all torque), and the holding brake is activated.
Number Designation Explanation
A/I/P/E Status Messages Status messages, no error, see p. 89
... Status Message Updating the startup configuration
F00 no error no error on the selected axis module
Heat sink temperature too high
F01* Heat sink temperature
limit is set by manufacturer to 80°
Overvoltage in DC bus link
F02* Overvoltage
limit depends on the electrical supply voltage
F03* Following error Message from the position controller
F04 Feedback Cable break, short-circuit, short to ground
Undervoltage in DC bus link
F05* Undervoltage
limit is set by manufacturer to 100V
Motor temperature too high or temp. sensor defect
F06 Motor temperature
limit is set by manufacturer to 145°C
Internal voltage
F07 Internal amplifier supply voltages are out of tolerance
supply
F08* Overspeed Motor runs away, speed is too high
F09 EEPROM Checksum error
F10 Flash-EPROM Checksum error
F11 Brake Cable break, short-circuit, short to ground
F12 Motor phase Motor phase missing (cable break or similar)
F13* Internal temperature Internal temperature too high
F14 Output stage Fault in the power output stage
F15 I²t max. I²t maximum value exceeded
F16* Supply BTB/RTO 2 or 3 phases missing in the mains supply feed
Error in the analog-digital conversion, normally caused
F17 A/D converter
by extreme electromagnetic interferences.
F18 Regen Regen circuit faulty or incorrect setting
F19* Supply phase A phase is missing in the mains supply power feed
F20 Slot fault Slot error (hardware fault on interface card)
F21 Handling error Software error on the interface card
F22 reserved reserved
F23 CAN-bus off Severe CAN bus communication error
F24 Warning Warning is displayed as fault
F25 Commutation error Commutation error
F26 Limit switch Homing error (hardware limit switch activated)
F27 reserved reserved
External position profile generator created a step, that
F28 External Trajectory
exceeded the maximum value
F29 Sercos Error only in SERCOS systems
F30 Emergency timeout Timeout emergency stop
F31 Macro Macro program error
F32 System Error system software not responding correctly
* = these error messages can be cleared without a reset, by using the ASCII command
CLRFAULT. If only one of these errors is present and the RESET button or the I/O
RESET function is used, only the CLRFAULT command will be executed.
More information to the messages can be found in the ASCII Object Reference
(Online Help), see parameter ERRCODE. Hints for removal can be found in the
Online help chapter "Trouble-Shooting".

9.7 Warning messages

Faults which occur, but which do not cause a switch-off of the amplifier output stage
(BTB/RTO contact remains closed), are indicated in the LED display on the front panel by
a coded warning number.
Number Designation Explanation
A/I/P/E Status Messages Status messages, no error, see p. 89
... Status Message Updating the startup configuration
n01 I²t I²t threshold exceeded
n02 Regen power Reached preset regen power limit
n03* S_fault Exceeded preset following error limit
n04* Response monitoring Response monitoring (fieldbus) has been activated
n05 Supply phase Mains supply phase missing
n06* SW limit switch 1 Underrun software limit switch 1
n07* SW limit switch 2 Overrun software limit switch 2
n08 Motion task error A faulty motion task was started
n09 No reference point No reference point (Home) set at start of motion task
n10* PSTOP PSTOP limit-switch activated
n11* NSTOP NSTOP limit-switch activated
Only for ENDAT or HIPERFACE® :
Motor default values
n12 discrepancy between motor number saved in the en-
loaded
coder and the amplifier, motor default values loaded
n13* reserved reserved
SinCos commutation (wake & shake) not completed,
n14 SinCos feedback will be canceled when amplifier is enabled and wake
& shake carried out
n15 Table error Fault according to speed/current table INXMODE 35
n16 Summarized warning Summarized warning for n17 to n31
The mode synchronization SYNCSRC is selected
n17 Fielbus Synchronization
but the drive isn’t in synchronies cycle
Using Multiturn encoder feedback, an overrun over
n18 Multiturn overrun
the maximum number of resolutions was detected
Motion task ramps are
n19 Range overflow on motion task data
limited
n20 Wrong GMT data Wrong "Graphical Motion Task" data
n21 PLC program error For details see plc code
max. motor temperatur The user can shut down the process before the tem-
n22
reached perature eror will interrupt the process immediately
n23...n31 reserved reserved
n32 firmware beta version Firmware is an unreleased beta version
* = these warning messages result in a controller shut-down of the drive (braking by
emergency stop ramp)
More information to the messages can be found in the ASCII Object Reference
(Online Help), see parameter STATCODE. Hints for removal can be found in the
Online help chapter "Trouble-Shooting".

9.8 Trouble Shooting

Depending on the conditions in your installation, there may be a wide variety of reasons
for the fault. In multi-axis systems there may be further hidden causes of a fault.
Detailled hints for removal of faults can be found in the Online help chapter
"Trouble-Shooting".
Our customer support can give you further assistance with problems.
Fault possible causes Measures to remove the fault

— wrong cable used — use null-modem cable
HMI message: — cable plugged into wrong posi- — plug cable into the correct so-
communication tion in ckets on the servo amplifier
fault servo amplifier or PC and PC
— wrong PC interface selected — select correct interface
— servo amplifier not enabled — apply enable signal
— break in setpoint cable — check setpoint cable
— motor phases swapped — correct motor phase sequence
motor does not — brake not released — check brake control
rotate — drive is mechanically blocked — check mechanism
— no. of motor poles set incor- — set no. of motor poles
rectly
— feedback set up incorrectly — set up feedback correctly
— gain too high (speed controller) — reduce Kp (speed controller)
motor oscilla- — shielding in feedback cable has — replace feedback cable
tes a break — join AGND to CNC-GND
— AGND not wired up
— Irms or Ipeak is set to low — increase Irms or Ipeak (keep
drive reports
within motor data !)
following error
— setpoint ramp is too long — shorten setpoint ramp +/-
motor overhea- — Irms/Ipeak set too high — reduce Irms/Ipeak
ting
— Kp (speed controller) too low — increase Kp (speed controller)
— Tn (speed controller) too high — use motor default value for Tn
drive too soft (speed controller)
— PID-T2 too high — reduce PID-T2
— T-Tacho too high — reduce T-Tacho
— Kp (speed controller) too high — reduce Kp (speed controller)
— Tn (speed controller) too low — use motor default value for Tn
drive runs
(speed controller)
roughly
— PID-T2 too low — increase PID-T2
— T-Tacho too low — increase T-Tacho
— offset not correctly adjusted for — adjust setpoint-offset (analog
axis drifts at analog setpoint provision I/O)
setpoint = 0V — AGND not joined to the — join AGND and CNC-GND
CNC-GND of the controls

BECKHOFF 06/2007 Appendix
10 Appendix
10.1 Glossary
C clock Clock signal
common-mode voltage The maximum amplitude of a disturbance (on both
inputs) which a differential input can eliminate
continuous power of regen circuit Mean power which can be dissipated in the
regen circuit
counts Internal count pulses, 1 pulse = 1/220 turn-1
current controller Regulates the difference between the current
setpoint and the actual value to 0
Output : power output voltage
D DC Bus link Rectified and smoothed power voltage
disable Removal of the enable signal (0 V or open)
E earth short electrical connection between a phase and
the protective earth (PE)
enable Enable signal for the servo amplifier (+24 V)
F fieldbus interface CANopen, PROFIBUS, SERCOS, EtherCat
free convection Free movement of air for cooling
G GRAY-code Special format for representing binary numbers
H holding brake Brake in the motor, which should only be used
when the motor is at standstill
I I²t threshold Monitoring of the r.m.s. current that is actually
required
incremental encoder interface Position signalling by 2 signals with 90° phase
difference, not an absolute position output
input drift Temperature and age-dependent alteration of an
analog input
Ipeak, peak current The effective value of the peak current
Irms, effective current The r.m.s. value of the continuous current
K Kp, P-gain Proportional gain of a control loop
L limit speed Maximum value for speed normalization at ±10 V
limit-switch Switch limiting the traverse path of the machine;
implemented as n.c. (break) contact
M machine The complete assembly of all connected parts or
devices, of which at least one is movable
motion-block Set of all the position control parameters
which are required for a motion task
multi-axis system Machine with several driven axes
N natural convection Free movement of air for cooling
O optocoupler Optical connection between two electrically
independent systems

Appendix 06/2007 BECKHOFF
P P-controller Control loop with purely proportional behaviour

phase shift Compensation for the lag between the electro-
magnetic and magnetic fields in the motor
PID-controller Control loop with proportional, integral and
differential behaviour
PID-T2 Filter time constant for the speed controller output
position controller Regulates the difference between the position
setpoint and the actual position to 0
Output : speed setpoint
potential isolation electrically decoupled
power contactor System protection device with phase monitoring
pulse power of the regen circuit Maximum power which can be dissipated in the
regen circuit
R regen circuit Converts superfluous energy, which is fed back
during braking, into heat in the regen resistor
reset New start of the microprocessor
reversing mode Operation with a periodic change of direction
ROD-interface Incremental position output
S servo amplifier Control device for regulating the speed, torque
and position of a servomotor
setpoint ramps Limits for the rate of change of the speed
setpoint
short-circuit here: electrically conductive connection between
two phases
speed controller Regulates the difference between the speed
setpoint and the actual value to 0
Output : current setpoint
SSI-interface Cyclic-absolute, serial position output
supply filter Device to divert interference on the power supply
cables to PE
T T-tacho, tachometer time constant Filter time constant in the speed feedback of
the control loop
tachometer voltage Voltage proportional to the actual speed
thermostat Temperature-sensitive switch built into the
motor winding
Tn, I-integration time Integral section of a control loop
Z zero pulse Output once per turn from incremental encoders,
used to zero the machine

10.2 Index
! 24V aux. supply, interface . . . . . . . . 47 M Maintenance . . . . . . . . . . . . . . . 13

Master-Slave . . . . . . . . . . . . . . . 56
A Abbreviations . . . . . . . . . . . . . . . 8 Motor, interface . . . . . . . . . . . . . 48
Ambient conditions . . . . . . . . . . . . 20 Mounting . . . . . . . . . . . . . . . . . 34
B BISS interface . . . . . . . . . . . . . . 51 Mounting position . . . . . . . . . . . . 20
Block diagram . . . . . . . . . . . . . . 43 Multi-axis systems
Brake. . . . . . . . . . . . . . . . . . . 21 connection example . . . . . . . . . 87
BTB/RTO. . . . . . . . . . . . . . . . . 66 parameterization . . . . . . . . . . . 86
C CANopen interface . . . . . . . . . . . . 68 N Nameplate . . . . . . . . . . . . . . . . 14
CE conformity . . . . . . . . . . . . . . 12 Noise emission . . . . . . . . . . . . . . 20
Commissioning. . . . . . . . . . . . . . 73 NSTOP, interface . . . . . . . . . . . . 64
Conductor cross-sections . . . . . . . . 20 O Operating systems . . . . . . . . . . . . 75
Connector assignments . . . . . . . . . 44 Options . . . . . . . . . . . . . . . . . . 17
Control signals . . . . . . . . . . . . . . 63 Outputs
D DC Bus link, interface . . . . . . . . . . 48 BTB/RTO . . . . . . . . . . . . . . . 66
Dimensions. . . . . . . . . . . . . . . . 35 DIGI-OUT 1/2 . . . . . . . . . . . . 65
Display, LED . . . . . . . . . . . . . . . 20 encoder emulations . . . . . . . . . 61
Disposal . . . . . . . . . . . . . . . . . 13 P Package supplied . . . . . . . . . . . . 14
E Earthing Packaging . . . . . . . . . . . . . . . . 13
installation . . . . . . . . . . . . . . 38 Part number scheme . . . . . . . . . . . 15
wiring diagram . . . . . . . . . . . . 45 PC connection . . . . . . . . . . . . . . 67
Enclosure protection . . . . . . . . . . . 20 PC interface cable . . . . . . . . . . . . 67
Encoder Pollution level . . . . . . . . . . . . . . 20
interface . . . . . . . . . . . . . . . 52 PROFIBUS interface . . . . . . . . . . . 69
interface Master-Slave . . . . . . . . 56 PSTOP, interface . . . . . . . . . . . . 64
Encoder emulations . . . . . . . . . . . 61 Pulse/direction, interface . . . . . . . . . 59
Error messages . . . . . . . . . . . . . 90 Q Quickstart, drive test . . . . . . . . . . . 76
EtherCat interface . . . . . . . . . . . . 71
R regen circuit . . . . . . . . . . . . . . . 22
F Fan . . . . . . . . . . . . . . . . . . . . 36 Regen circuit . . . . . . . . . . . . . . . 22
Fieldbus interface . . . . . . . . . . . . 68 Regen resistor
Forming . . . . . . . . . . . . . . . . . 73 external interface. . . . . . . . . . . 48
Fusing . . . . . . . . . . . . . . . . . . 19 techn. data . . . . . . . . . . . . . . 22
G Glossary . . . . . . . . . . . . . . . . . 93 Resolver . . . . . . . . . . . . . . . . . 50
Ground symbol . . . . . . . . . . . . . . 39 ROD, interface . . . . . . . . . . . . . . 61
Grounding system . . . . . . . . . . . . 22 RS232/PC, interface . . . . . . . . . . . 67
Guide S Safety instructions . . . . . . . . . . . . . 9
electrical installation . . . . . . . . . 38 SERCOS interface . . . . . . . . . . . . 70
mechanical installation . . . . . . . . 33 Setpoint input . . . . . . . . . . . . . . 63
H Hall, interface . . . . . . . . . . . . . . 54 Setup software . . . . . . . . . . . . . . 74
Hardware requirements . . . . . . . . . 75 Shield connection . . . . . . . . . . . . 40
I Incremental encoder, interface . . . . . . 55 Shielding
Inputs installation . . . . . . . . . . . . . . 38
ANALOG IN . . . . . . . . . . . . . 63 wiring diagram . . . . . . . . . . . . 45
DIGI-IN 1/2 . . . . . . . . . . . . . . 64 Sine-cosine encoder, interface . . . . . . 53
enable . . . . . . . . . . . . . . . . 66 Site altitude. . . . . . . . . . . . . . . . 20
encoder. . . . . . . . . . . . . . . . 52 SSI, interface. . . . . . . . . . . . . . . 62
Encoder for Master Slave . . . . . . 56 Stacking height. . . . . . . . . . . . . . 13
NSTOP . . . . . . . . . . . . . . . . 64 Standards . . . . . . . . . . . . . . . . 11
power supply . . . . . . . . . . . . . 47 Status display . . . . . . . . . . . . . . 88
PSTOP . . . . . . . . . . . . . . . . 64 Storage. . . . . . . . . . . . . . . . . . 13
resolver. . . . . . . . . . . . . . . . 50 Supply connection, interface . . . . . . . 47
Installation Supply voltage . . . . . . . . . . . . . . 20
electrical . . . . . . . . . . . . . . . 37 Switch on/off behavior . . . . . . . . . . 23
mechanical . . . . . . . . . . . . . . 33 Symbols . . . . . . . . . . . . . . . . . . 7
software . . . . . . . . . . . . . . . 75 System components, summary . . . . . 42
K Key operation . . . . . . . . . . . . . . 88
L Leakage current . . . . . . . . . . . . . 31
LED display . . . . . . . . . . . . . . . 88
Limit-switch inputs . . . . . . . . . . . . 64

Appendix 06/2007 BECKHOFF
T Technical data . . . . . . . . . . . . . . 18
ambient conditions . . . . . . . . . . 20
cables . . . . . . . . . . . . . . . . 41
conductor cross sections . . . . . . . 20
connections. . . . . . . . . . . . . . 19
fusing . . . . . . . . . . . . . . . . . 19
rated data . . . . . . . . . . . . . . 18
tightening torques . . . . . . . . . . 19
Technical description. . . . . . . . . . . 16
Tightening torques, connectors . . . . . 19
Transport . . . . . . . . . . . . . . . . . 13
Trouble shooting . . . . . . . . . . . . . 92
U Use as directed
servo amplifier . . . . . . . . . . . . 10
setup software . . . . . . . . . . . . 74
V Ventilation
installation . . . . . . . . . . . . . . 33
techn. data . . . . . . . . . . . . . . 20
Vibrations . . . . . . . . . . . . . . . . 20
W Warning messages. . . . . . . . . . . . 91
Wiring . . . . . . . . . . . . . . . . . . 39
Wiring diagram
axis module. . . . . . . . . . . . . . 46
master . . . . . . . . . . . . . . . . 45


Ax2500 en

Uploaded by

Copyright:

Available Formats

Ax2500 en

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ax2500 en

Uploaded by

Copyright:

Available Formats

Digital Servo Amplifier

Assembly, Installation, Setup

WINDOWS is a registered trademark of Microsoft Corp.

AX2500 Product Manual 3

AX2500 Product Manual 5

This page has been deliberately left blank.

6 AX2500 Product Manual

This manual makes the following demands on qualified personnel :

1.2 Hints for the online edition (PDF format)

1.3 Symbols used

ð p. see page l special emphasis

AX2500 Product Manual 7

1.4 Abbreviations used

8 AX2500 Product Manual

AX2500 Product Manual 9

2.2 Use as directed

Mains voltage Servo amplifier

l If the servo amplifiers are used in residential areas, or in business or commercial

10 AX2500 Product Manual

3.2 American Directives and Standards

3.3 Asian Directives and Standards

AX2500 Product Manual 11

3.4.2 UL and cUL- Conformance

This servo amplifier is listed under UL file number E217428.

12 AX2500 Product Manual

4.4 Maintenance / Cleaning

AX2500 Product Manual 13

Accessories: (must be ordered separately if required)

Servo amplifier type Serial number Comments Enclosure Rating

Eiserstr. 5 Tel.: +49-(0)5246/963-0 C UL

Spannungsversorgung Power Supply Nennstrom Nom. Current Schutzart Encl.Rating

max. ambient Electrical supply Output current

14 AX2500 Product Manual

5.3 Part number scheme

Voltage rating Function

Comparison (without expansion) device name -> UL part number

Device Name UL Part Number

AX2500 Product Manual 15

16 AX2500 Product Manual

Auxiliary voltage 24V DC

Operation and parameter setting

Completely digital control

AX2500 Product Manual 17

6.2 Technical data

max. 230VAC max. 400VAC

18 AX2500 Product Manual

6.2.2 Inputs / Outputs

Analog input, 14-bit resolution V ±10

6.2.3 Recommended tightening torques

Connector Tightening torque

AX2500 Product Manual 19

6.2.5 Ambient conditions, ventilation, mounting position

Storage, transport ð p.13

6.2.6 Conductor cross-sections

Technical requirements to cables ð p.41.

AC connection 1.5 mm², depending on the system fusing

6.3 LED display

20 AX2500 Product Manual

6.4 Control for motor holding brake