Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 70 views

    Triflex ™ 3-Layer Combinations: Technical Data Sheet

    Uploaded by

    Santosh Jayasaval

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Triflex ™ 3-Layer Combinations: Technical Data Sheet

    Uploaded by

    Santosh Jayasaval
    70 views2 pages

    Original Title

    Untitled

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    70 views2 pages

    Triflex ™ 3-Layer Combinations: Technical Data Sheet

    Uploaded by

    Santosh Jayasaval

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 2

    TECHNICAL DATA SHEET

    1001 Page 1 of 2

    1001
    TRIFLEX™ 3-LAYER COMBINATIONS March 2015

    Polycorp 1001 is 55A durometer black chemical cure “Triflex™” Soft-Hard Soft natural rubber lining.
    It provides a combination of excellent abrasion and chemical resistance. Lining is flexible to
    withstand expansion and contraction due to rapid changes in temperature. It is FDA compliant as
    per 21CFR177.2600. For FDA service use activator C-600 activator, for non-FDA service use
    o o
    activator C-700. Operating temperature range is from 50°F (10 C) to 160°F (71 C).

    APPLICATION NOTES: CURING:


     Skive – use closed skive construction Cure time adjustments may be required to
     Repair – same. Refer to section 11 of application compensate for specific conditions. See Section 10
    manual
    of the Application Manual for detailed instructions.
     Cured Durometer – Shore A Durometer of top
    surface: 55 ± 10.
     Special Treatment After Application – After Ambient Cure – The chemical cure lining will
    application, brush the rubber surface with three vulcanize in about 2-3 weeks at 85°F. If service
    (3) separate coats of C-600 or C-700 activator. o o
    temperature is above 150 F (127 C), the lining could
    Allow to dry for 30 minutes between each coat.
    be immediately put in service.
     Spark Test – Refer to section 13 of the
    Application Manual
     Do not use in transport equipment Atmospheric Steam Assist – Introduce steam
    sufficient to ensure contact with all surfaces.
    ADHESIVE NOTES: Approximately 4-6 hours will be required to cure
    See Section 6 of the Polycorp Rubber Lining Application lining. More time may be necessary in a large tank or
    Manual for specific cementing / adhesion notes. if heat losses are large.
    o
    For proper adhesion, temperatures must be over 60 F
    o o o
    (15 C) and must not exceed 120 F (49 C).
    Use adhesives in well ventilated area and always consult
    the material safety data sheet for specific precautions.

    Polycorp Approved
    Coat
    Adhesive Equivalent
    st
    1 Coat on Metal C-90 Primer Chemlok 289
    nd
    2 Coat on Metal C-91 Intermediate Chemlok 290
    rd
    3 Coat on Metal C-202S Tack Chemlok 286
    th
    4 Coat on lining C-202S Tack Chemlok 286

    INNOVATION / QUALITY / SOLUTIONS / TECHNICAL SUPPORT


    +1-519-846-2075 / +1-800-265-2710 / www.poly-corp.com
    TECHNICAL DATA SHEET
    1001 Page 2 of 2

    STORAGE:
    Store in a cool,dry area.
    Shelf Life
    o
    Stored below 50 F (10oC) 180 days
    o
    Stored between 51 and 70 F 90 days
    o
    Stored between 71 and 90 F 45 days
    o
    Do not store above 90 F (32oC)

    Depending on storage conditions it may be possible to use rubber linings beyond the recommended shelf life
    however additional testing must be completed. Please contact Polycorp for recommended test procedures. A
    sample of the rubber lining can also be sent back to Polycorp for verification.

    Storage, handling and application methods must conform to the Polycorp Rubber Lining Application Manual.

    TYPICAL PROPERTIES:
    Property Value ASTM Test Method

    Hardness (Face) (points) 50 A ± 10 D2240

    Tensile Strength (min, psi) N/A D412

    Elongation at Break (min, %) N/A D412

    Specific Gravity 1.357 D297

    Adhesion to Metal (min, lbf/in) 25 D429


    o o
    Operating Temperature Range for Optimum 50°F (10 C) to 160°F (71 C) N/A
    Service Life

    All physical property values developed and measured using a press-cured sample sheet prepared in accordance
    with ASTM D3182.

    INNOVATION / QUALITY / SOLUTIONS / TECHNICAL SUPPORT


    +1-519-846-2075 / +1-800-265-2710 / www.poly-corp.com

    You might also like